Contents

Titan EP2300 0294036 Pump Owner's Manual PDF

1 of 33
1 of 33

Summary of Content for Titan EP2300 0294036 Pump Owner's Manual PDF

Diaphragm Pumps 1150

Piston Pumps EP2105 EP2205 EP2300 EP2300se EP2400 EP2510 GP2605 GP2905

HVLP CS5100 CS8100 CS9100 Maxum II Gun

i

i t

II

1

EP2300 Piston Pump

1297 1997 Wagner Spray Tech. All rights reserved. Form No. 0294724E

Model Numbers: 0294006 Cart Mount 0294036 Low Boy

SprayTECH 1770 Fernbrook Lane Minneapolis, MN 55447

Owner's Manual

2

GROUNDING INSTRUCTIONS This product must be grounded. In the event of an electrical short circuit, grounding reduces the risk of electric shock by providing an escape wire for the electric current. This product is equipped with a cord having a grounding wire with an appropriate grounding plug. The plug must be plugged into an outlet that is properly installed and grounded in accordance with all local codes and ordinances.

If repair or replacement of the cord or plug is necessary, do not connect the green grounding wire to either flat blade terminal. The wire with insulation having an outer surface that is green with or without yellow stripes is the grounding wire and must be connected to grounding pin.

Check with a qualified electrician or serviceman if the grounding instructions are not completely understood, or if in doubt as to whether the product is properly grounded. Do not modify the plug provided; if it will not fit the outlet, have the proper outlet installed by a qualified electrician.

This product is for use on a nominal 120 volt circuit, and has a grounding plug that looks like plug illustrated in sketch A. A temporary adapter which looks like the adapter illustrated in sketch B and C, may be used to connect this plug to a 2 pole receptacle as shown in sketch B if a properly grounded outlet is not available. The temporary adapter should be used only until a properly grounded outlet (sketch A) can be installed by a qualified electrician. The green colored rigid ear lug, or the like extending from the adapter must be connected to a permanent ground such as a properly grounded outlet box cover. Whenever the adapter is used, it must be held in place by a metal, screw.

(A)

(B)

(C)

WARNING Improper installation of the grounding plug can result in a risk of electrical shock.

IMPORTANT EXTENSION CORD SELECTION

If an extension cord is used, make sure it is of the three-conductor type with NEMA connectors so a continuous grounding circuit is provided from tool to power circuit receptacle. Also, be sure that the conductor size is large enough to prevent excessive voltage drop which will cause loss of power. A table of recommended extension cord sizes will be found below.

For nameplate ampere ratings which are between those given, use the extension cord recommended for the NEXT higher ampere rating.

If an extension cord is to be used outdoors it must be marked with the suffixi W-A following the cord type designation. For example SJTW-A to indicate it is acceptable for outdoor use.

RECOMMENDED EXTENSION CORD SIZES FROM SERVICE ENTRANCE TO PUMP MOTOR.

NAMEPLATE AMPERE RATING Cord Lgth. 0 to 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 25Ft. 18 18 18 18 18 18 16 16 16 14 14 14 14 14 12 12 50Ft. 18 18 18 18 18 18 16 16 16 14 14 14 14 14 12 12I 25Ft. 18 18 18 18 18 18 16 16 16 14 14 14 14 14 12 12

100Ft. 18 18 18 16 16 16 16 16 14 14 14 14 14 14 12 12 125Ft. 18 18 16 16 16 14 14 14 14 14 14 12 12 12 12 12 150Ft. 18 16 16 16 14 14 14 14 14 12 12 12 12 12 12 12

3

CONTENTS Safety Warnings......................................................... 4-6 Specifications.................................................................7 Initial Set-up................................................................... 7 Purging & Priming.......................................................... 8 Operation....................................................................... 9 Setting the Pressure...................................................... 9 Using the Spray Gun....................................................10 Pressure Relief Procedure...........................................10 Prime the Sprayer with Paint....................................... 10 Spraying Technique..................................................... 11

SAFETY PRECAUTIONS This manual contains information which must be read and understood before using the equipment. When you come to an area which has one of the following symbols, pay particular attention and make certain to heed the safeguard.

WARNING Important safety information indicates a hazard which may cause serious injury or loss of life.

CAUTION Important information that tells how to prevent damage to equipment or how to avoid causes of minor injuries.

Note: Gives important information which should be given special attention.

Clean-up.......................................................................12 Maintenance.................................................................13

Daily Maintenance......................................................13 Repacking the Fluid Section.......................................14 Motor Brush Replacement..........................................16

Trouble Shooting...........................................................17 Parts List...............................................................19 - 29 Accessories..................................................................30 Warranty........................................................Back Cover

4

Maximum operating range of the gun - 3000 PSI fluid pressure.

NEVER aim the gun at any part of the body.

NEVER allow any part of the body to come in contact with the fluid stream. DO NOT come in contact with a fluid stream created by a leak in the fluid hose.

NEVER put hand in front of the gun. Gloves will not provide protection against an injection injury.

ALWAYS lock the gun trigger,shut fluid pump off and release all pressure before servicing, cleaning tip guard, changing tips, or leaving unattended. Simply turning off the motor will not release pressure in the system. The Prime Spray Valve must be turned to the position to relieve the pressure. See Pressure Relief Procedure, Page 10.

ALWAYS have the tip guard in place while spraying. The tip guard provides some protection against injection injuries but is mainly a warning device.

ALWAYS remove spray tip before flushing or cleaning the system.

WARNING PREVENTIONHAZARD

NEVER use a spray gun which does not have a trigger lock or trigger guard in place and in working order.

All accessories must be rated at or above 3000 PSI (Includes spray tips, guns, extensions, and hose).

Injection Injury - A high pressure stream of paint pro- duced by this equipment can pierce the skin and underlying tissues, leading to serious injury and pos- sible amputation.

DO NOT TREAT AS A SIMPLE CUT! Injection- can lead to amputation. See a physician im- mediately.

NOTE TO PHYSICIAN: Injection into the skin is a traumatic injury. It is important to treat the injury surgically as soon as possible. DO NOT delay treatment to research toxicity. Toxicity is a concern with some coatings injected directly into the blood stream. Con- sultation with a plastic surgeon or recon- structive hand surgeon may be advisable.

Paint hose can develop leaks from wear, kinking, abuse etc. A leak is capable of injecting material into the skin. The paint hose should be inspected before each use.

In case of skin injection, see physician immediately.

5

WARNING HAZARD

Explosion or fire - Solvent and paint fumes can explode or ignite causing property damage and or severe injury.

Exhaust and fresh air introduction must be provided to keep the air within the spray area free from accumulation of flammable vapors.

Avoid all ignition sources such as static electricity sparks, open flames such as pilot lights, hot objects such as cigarettes, and sparks from connecting and disconnect- ing power cords and working light switches.

Fire extinguishing equipment must be present and in working order.

Keep the pump away from spray area to avoid solvent and paint fumes.

High velocity flow of material through equipment may develop static electricity. The equipment being used, and objects in and around the spray area must be properly grounded to prevent static discharge and sparks.

Use only conductive or grounded high pressure fluid hoses for airless applications. Be sure that gun is grounded through hose connections.

Follow the material and solvent manufacturer's safety precautions and warnings.

WHEN FLUSHING EQUIPMENT use lowest possible pressure.

PREVENTION

6

Halogenated hydrocarbon solvents such as methylene chloride and 1,1,1 - Trichlorethane are not compatible with aluminum and may cause an explosion. If unsure of a materials compatibility with aluminum, contact your coating's supplier.

Some spray guns and accessories cannot be used with halogenated hydrocarbon solvents. Be certain of com- patibility before use with halogenated hydrocarbon sol- vents.

The SprayTech EP2300 pump is NOT compatible for use with halogenated hydrocarbon solvents. The SprayTech G-05, G-09, and G-10 guns must not be used with halogenated hydrocarbon solvents.

WARNING PREVENTIONHAZARD

Explosion hazard incompatible materials - May cause property damage or severe injury.

General - May cause property damage or severe injury.

Hazardous vapors - Paints, solvents, insecticides, and other materials may be harmful if inhaled causing se- vere nausea, fainting, or poisoning.

Read all instructions and safety precautions before oper- ating.

Comply with all appropriate local, state and national codes governing ventilation, fire preventive, and opera- tion.

The United States Government Safety Standards have been adopted under Occupational Safety and Health Act. These standards, particularly the General Stan- dards, Part 1910 and construction Standard, Part 1926, should be consulted.

This high- pressure airless pump is designed to be used with authorized SprayTech parts only. When using this pump with parts that do not comply with the minimum specifications and safety devices of the pump manufac- turer, the user assumes all risks and liabilities.

Before each use, check all hoses for cuts, leaks, abra- sion or bulging of cover or damage or movement of couplings. If any of these conditions exist, replace the hose immediately. Never repair a paint hose. Replace it with another grounded hose.

All hoses, swivels, guns, and accessories used with this unit must be pressure rated at or above 3000 PSI.

Use a respirator or mask whenever there is a chance that vapors may be inhaled. Read all instructions with the mask to assure that it will provide the necessary protec- tion against the inhalation of harmful vapors.

7

SPECIFICATIONS MODEL EP2300

1. GPM----------------------------------------------------------2/3 2. Maximum pressure------------------------------- 3000 PSI 3. Motor - electric ------------------------------------------1 HP 4. Amperage-------------------------------------------8.5 Amps 5. Cycle------------------------------------124 cycles per min. 6. Maximum Tip Size @2000 psi---------------------- .023"

(Latex paint)

1. Attach handle to cart using bolts and knobs provided. Insert bolt through square hole in handle and then through hole in cart leg. Secure with knob. Repeat other side.

2. Remove protector cap on outlet fitting and install air- less hose. DO NOT INSTALL SPRAY TIP(S) IN GUN(S) AT THIS POINT.

INITIAL SET-UP The SprayTech EP2300 Piston Pump unit is fully assembled upon delivery. Follow these simple steps for set-up:

CART MOUNT/LOW BOYLOWBOY

1. Remove the plug from the inlet elbow on the fluid section.

2. Attach the suction set fitting into the inlet elbow on the fluid section.

3. Attach the return line to the tube fitting at the dump valve.

4. Remove protector cap on outlet fitting and install air- less hose. DO NOT INSTALL SPRAY TIP(S) IN GUN(S) AT THIS POINT.

SprayTech EP2300 Low Boy Piston Pump

Figure 1. SprayTech EP2300 Cart Mounted Piston Pump

7. Max. Hose Length @ 2000 PSI-----------------100 feet 8. Weight:

LowBoy--------------------------------------------------63 lbs. Cart Mount--------------------------------------------- 64 lbs.

9. Dimensions: Cart Mount -------------------------------30"Lx39''Hx21''W LowBoy------------------------------------28L x 21H x 21W

(38H with Handle)

Figure 2. Install Siphon Tube

8

4. Set Prime/Spray Ball Valve to the Prime position.

Figure 5. Set Prime/Spray Ball Valve to Prime

5. Turn the ON-OFF switch to the ON position.

6. Gradually increase pressure by turning Pressure Con- trol Knob clockwise.

7. Watch for fluid to start coming through return tube. Use minimum pressure necessary to keep fluid flowing.

8. When test fluid is purged, soapy water will flow through the return. Turn pressure down to minimum and replace soapy water bucket with clear water.

9. Increase pressure again and let unit run until water running through the return line is clear.

10. Decrease pressure. Replace clean water container with bucket of latex paint.

11. Increase pressure slowly until paint comes through the return tube. Place return hose back into operating position above paint bucket. Keep recirculating until the paint coming through the return tube is free of air bubbles.

12. Decrease pressure to minimum setting (counter-clock- wise). The unit is now ready to use. (See Operating the Sprayer, page 9.)

PURGING AND PRIMING

This unit is shipped with test fluid in the fluid section to prevent corrosion during shipment and storage.

For spraying with solvent-based paint, thorough flushing of this material is not necessary.

If you are going to spray with LATEX paint, this fluid must be thoroughly cleaned out of the system.

KEEP SPRAY GUN LOCKED AND IN THE OFF POSI- TON DURING ALL THESE STEPS.

Purging System for Latex Paint

1. Place a bucket of soapy water under the paint suction tube. Also, have a waste container handy to catch the purged fluid.

2. Place paint return hose into the waste container.

Figure 4. Turn Pressure Control Knob Counter-Clockwise to Reduce Pressure

Figure 3. Place return hose so purged fluid goes into waste container.

WARNING If a metal container is used, ground the gun by holding it against the

edge of the container while flushing (As shown below). Failure to do so may lead to static electric discharge, which may cause a fire.

9

For a new unit, follow purging and priming steps above. For units already in service, also purge water or solvent from the system as described above, depending on the type of paint being used.

After pump is primed and ready to spray, it may also be necessary to purge the hoses of water or solvent.

1. Set Pressure Control Knob to minimum setting (counter- clockwise).

2. Set Prime/Spray Ball Valve to Spray .

3. Be sure spray gun still has no tip installed.

4. Unlock spray gun.

5. Increase pressure by turning Pressure Control Knob clockwise.

6. Trigger gun into waste container until solvent or water is purged from the hose.

7. Decrease pressure by turning Pressure Control Knob counter-clockwise.

8. Set Prime/Spray Ball Valve to Prime, and trigger gun to be sure no pressure is left in the hose.

9. Lock gun off.

10. Install spray tip appropriate for the material being sprayed. (The thicker the paint, the larger the spray tip required.)

11. Re-set Prime/Spray Ball valve to Spray.

12. Increase pressure to maximum setting (turn Pressure Control Knob clockwise).

13. Release gun lock.

14. Trigger gun to test spray pattern. Spray against a scrap piece of pasteboard or other test surface.

15. See Setting the Pressure, below.

Setting the Pressure The best pressure setting will vary with the type of paint and the size and type of nozzle. The thicker the paint, the higher the pressure needed.

To find the optimum pressure setting, start with the Pres- sure Control Knob turned fully clockwise (maximum pres- sure). Gradually decrease the pressure by turning the knob counter-clockwise to the minimum level necessary to main- tain the desired spray pattern and atomization.

Until you are satisfied with the spray pattern, spray on a test surface rather than on the surface to be painted.

Purging System for Solvent-Based Paint If you are going to spray solvent-based paint, all you need to do is purge the fluid. Thorough cleaning is not necessary as it is with latex paint.

NOTE: KEEP SPRAY GUN LOCKED OFF DURING ALL THESE STEPS.

1. Put full paint bucket into position.

2. Place return hose over waste container. (See Figure 3.) Attach paint hose without tip and put into waste container.

3. Set Pressure Control Knob full counter-clockwise (mini- mum pressure). (See Figure 4.)

4. Set Prime/Spray Ball Valve on Prime . (See Figure 5.)

5. Turn the ON-OFF switch to the ON position.

6. Turn Pressure Control Knob clockwise to increase pressure until fluid starts to come through return tube into waste container.

7. When paint starts to flow through return tube, decrease pressure to minimum setting and place return tube over paint bucket.

8. Continue recirculating until paint flowing through return tube is free of bubbles.

9. Install spray tip.

10. You are now ready to spray.

OPERATION

Before starting spraying every day, squirt upper packing lubricant (Part No. 9992504) into slots in packing nut cover. Do not apply so much that it overflows and drips into the paint. This lubricant keeps the piston seals pliant, minimiz- ing paint by-pass and piston wear. If unit is operated several hours a day, repeat lubrication after about 4 hours.

Figure 6. Oil Upper Pump Packings

10

1. Engage the gun safety latch.

2. Shut off the motor and turn the pressure control knob counterclockwise as far as possible.

3. Turn the prime/spray ball valve to prime, having a pail ready to catch the drainage or return to the paint container via the return hose.

4. Disengage the gun safety latch.

5. Hold metal part of the gun firmly to the side of a metal pail to avoid a build up of static electricity, and trigger the gun into the metal container to relieve the pressure.

6. Engage the gun safety latch.

7. Leave the prime/spray ball valve on prime, until you are ready to operate the sprayer again.

WARNING the unit down for any purpose, including servicing or adjusting any part of the spray system, changing or cleaning spray tips, or preparing for clean-up.

Be sure to follow the Pressure Relief Procedure when shutting

Using the Spray Gun

NOTE: FOLLOW THE INSTRUCTIONS THAT CAME WITH YOUR GUN.

PRESSURE RELIEF PROCEDURE

Prime the Sprayer with Paint 1. Turn the prime/spray ball valve to prime.

2. Put the suction tube into the paint container.

3. Turn the pressure control knob counterclockwise as far as possible to the lowest pressure setting.

4. Start motor. Slowly increase pressure by turning the pressure control knob clockwise until pump begins to function. When paint begins to flow through return tube decrease pressure by turning the pressure control knob counterclockwise and then turn the prime/spray ball valve to the spray position.

5. Disengage the gun safety latch.

6. Hold a metal part of the gun firmly against and aimed into a metal waste container. Trigger the gun and hold it open while slowly increasing the pressure setting by turning the pressure control knob clockwise until the sprayer starts. Keep the gun triggered until all the air is forced out of the system and paint is flowing freely. Release the trigger and engage the safety latch.

7. Check all fluid connections for leaks. If any are found, follow the pressure relief procedure before tightening the connection.

11

Spraying Technique

You can learn to spray paint as easily as you can learn to paint with a brush or roller. You can get a professional looking job in a safe manner by following the spray painting tips below.

1. Heed all WARNINGS and CAUTIONS that are listed on pages 3 thru 6 at the front of this manual. Take time out now to reread them.

2. Avoid sharp bending and kinking of the paint hose. All paint hoses should be kept clear of traffic and sharp cutting edges or objects.

3. Use the lowest pressure possible when spraying. Too much pressure shortens equipment life. It also causes faster than normal wear on the spray tip.

4. Determine the best spraying distance (distance from spray tip on the spray gun to the work). If the spray gun is held too close to the work, you will have paint buildup that will cause sags and runs. If the spray gun is held too far from the work, "fogging" will result.

The correct distance should be about 10 to 12 inches. Keep this distance for the entire length of the stroke. Of course, the shape of some work surfaces will not permit this. However, the same spraying distance should be kept whenever possible.

5. Do not move the spray gun by flexing your wrist. The result of this is shown in Figure 7. Rather, move the spray gun with a smooth stroke of the entire arm and shoulder. Maintain the same arm speed all the way through the stroke. The result of this is shown in Figure 8.

Work

Heavy Coat

Wrong Way to Spray

Light Coat

Light Coat

Figure 7. - Result of flexing wrist while spraying.

Approximatley 10 to 12 Inches

Even Coat on Work Throughout

Right Way To Spray

Steady Arm

Figure 8. - Result of smooth arm stroke and steady, even speed while spraying.

6. Keep the spray gun perpendicular to the work as shown in Figure 9.

Figure 9. - Right and wrong ways to hold spray gun toward work.

Wrong Way

Right Way

Approximately 10 to 12 inches

NOTE: WHEN SPRAYING BLOCK FILLER, MASTICS OR HIGH SOLID COATING LEAVE OUT GUN FILTER

AND HIGH PRESSURE FILTER SCREENS.

12

7. The spray gun should be triggered (turned off and on) on each stroke. This will save paint and avoid paint buildup at the end of the stroke. However, do not trigger during the middle of a stroke. This will result in an uneven spray and splotchy work. See Figure 10 for proper triggering on a left-to-right stroke. Reverse for a right-to-left stroke.

8. Move the spray gun at a rate of speed that is comfort- able for you. If you have to move your arm too fast in order to prevent excessive paint buildup, either (1) lower the pressure by turning the pressure control knob counterclockwise, or (2) use a spray tip with a smaller hole. If you have to move your arm too slow in order to get a good coating, either (1) raise the pressure by turning the pressure control knob clockwise, or (2) use a spray tip with a larger orfice. You should always keep the spray gun moving when making a stroke. Slowing down in one place will cause sags or runs.

CLEAN-UP

1. Turn power switch to OFF.

2. Bleed off any pressure remaining in the pump by opening the dump valve.

3. Remove gun tip and clean with solution compatible with material applied.

4. Remove paint container from its position directly below siphon hose and paint strainer. Replace with a con- tainer of solvent compatible with material being ap- plied.

5. Turn the pressure control knob counter-clockwise to the lowest pressure setting.

6. Turn power switch to ON.

7. Trigger spray gun(s) into container to flush pump, hose and gun(s) clean.

8. Turn power switch to OFF.

9. Bleed off solvent.

10. Unplug unit and store in a clean dry area.

For long-term storage, be sure to flush unit with appropriate oil before storing.

The pump, hose and gun should be cleaned thoroughly after daily use.CAUTION

Failure to do so permits material to cake, seriously affecting the performance of the unit.

Figure 10. - Proper way to trigger spray gun.

9. Overlap each stroke by about 40% to 50%. The overlap will assure a paint coating that is uniform across the work. One way to get good overlap is to point the spray gun at the edge of the last stroke.

Start Stroke

Pull Trigger

End Stroke

Release Trigger

Even Steady Stroke

Approximatley 10 to 12 Inches

Work

WARNING When cleaning the pump, hose and gun with mineral spirits or any

other solvent, ALWAYS spray at minimum pressure with the gun nozzle tip removed. Static electricity build-up may result in a fire or explosion in the presence of flammable vapors.

After daily use, paint should be flushed from the unit with solvent compatible with the material applied, and then re- flushed with mineral spirits.

13

MAINTENANCE Routine operator maintenance on this unit is minimal. Only three daily procedures are required: (1) lubricating the upper packings, (2) cleaning the high pressure filter screen, and (3) cleaning the intake screen.

Daily Maintenance

1. Squirt upper packing lubricant into slots in upper pump housing. Do not over-lubricate, as this will result in oil dripping into the paint. Oil approximately every four hours of operation.

Figure 13. Clean paint intake screen daily, or more often if needed.

Figure 11. Squirt upper packing lubricant into upper cylinder housing every four hours.

2. Clean high pressure filter, as needed. Remove filter housing. (Filter canister is threaded into base with right-hand threads.) Take out filter element and wash thoroughly. Scrub gently with a fiber-bristle brush if necessary (DO NOT use a wire brush). If spraying block fillers, mastics, etc. leave filter element out.

Figure 12. Remove and clean High-Pressure Filter at least daily, more often if needed.

3. Inspect paint intake screen (at bottom of paint suction tube) and wash if necessary. (Screen is threaded onto suction tube. Remove by turning counter-clockwise.)

Siphon tube

Screen

PTFE tape

Filter Housing

Filter Support

O-Ring Filter Element

14

Refer to Figure 14 (left).

1. Loosen and remove siphon tube assembly by turning counterclockwise.

2. Remove front cover.

3. Remove packing nut cover.

4. Run the unit in short intervals until the connecting pin is in front of the recessed area of the housing.

5. Disconnect the power cord from the electrical supply.

6. Remove the retainer clip on the yoke.

7. Remove the connecting pin by pushing it through the yoke and piston rod.

8. Loosen and remove fluid hose.

9. Loosen large locknut (7) on upper end of fluid section.

10. Unscrew entire fluid section assembly by turning coun- terclockwise.

11. Using wrench flats on inlet valve holder (28), position fluid section vertically into vise. Tighten vise.

12. Locate wrench flats on cylinder (8). Turn cylinder counterclockwise with large adjustable wrench until it is removed from the inlet valve holder (28).

13. Remove and inspect upper O-Ring (22) in inlet valve holder. If damaged, replace when re-installing.

14. Remove inlet valve holder (28) from vise. Tap out ball stop disc (23), ball cage (25) and ball (24).

If any parts are difficult to disassemble, soak in lacquer thinner until paint softens.

15. Remove lower ball seat (26). Inspect the ball and ball seat for damage. If seat is worn or damaged it can be flipped to the unused side. Ball must be replaced if damaged or if the seat is flipped.

Figure 14 - Fluid Section

WARNING ALWAYS follow the Pressure Relief Procedure (page 10)

before starting any troubleshooting, servicing, or cleaning.

Repacking the Fluid Section

A small amount of paint by-passing the piston and coming out of the slots in the upper piston housing is normal, but if it becomes excessive, or if paint pressure drops, the piston packings need to be replaced.

CAUTION Do not run motor with fluid section removed.

Inlet and Outlet Valve carbide seats are reversible. If one side becomes worn or damaged, flip the seat to the un-used side.

NOTE:

Continued on next page.

*2

*4

7

8

*14

#26

#18 *#17

* Included in Packing Kit P/N 0294905.

# Included in Valve Kit P/N 0294689.

*#27

*#24

*#22

16 15

*12*13

*11

10

*9

*6 *5

*3

1

20 21

23

25

28

*#19

1994, rev. 1995 Wagner Spray Tech Corporation. All rights reserved.

15

Repacking Fluid Section

Continued from Page 14

(Refer to Figure 14, Page 14) 16. Remove lower O-Ring (27) from inlet valve holder. 17. Place cylinder (8) in vise (on wrench flats) and

tighten.

18. Remove packing nut (1). 19. Gently hammer piston assembly down with rubber

mallet. Piston assembly will come out.

20. Remove lower packings (12, 13) and lower female adapter (14) if they have not already fallen out.

21. Remove lower male adapter (11) and wave spring (9). 22. Remove upper packings (3, 4 ) and adapter (2, 5) and

wave spring (6). 23. Insert connecting pin through hole in piston rod (10).

Lock connecting pin in vise jaws so piston rod is vertical. DO NOT put piston rod itself in vise. The vise jaws will damage piston rod.

24. Remove jam nut (21). 25. Remove piston seat retainer (20) with 5/16'' allen

wrench. 26. Remove piston rod assembly from vise. 27. Remove washer (19), ball seat (18), ball (17), ball

cage(16) and ball stop disc (15) from lower end of piston rod assembly.

28. Inspect ball, and ball seat for damage. If the seat is worn or damaged it can be flipped to the un-used side. Ball must be replaced if damaged or the seat is flipped. Washer must be replaced.

29. Hold piston assembly in vice using same procedure as step 23.

30. Insert upper ball stop disc (15), ball cage (16), ball (17), ball seat (18), and washer (19) into piston assembly.

31. Put removable loctite on piston seat retainer (20). Insert into piston assembly and tighten. Torque to 250 in./lbs.

32. Put removable loctite on jam nut (21). Tighten onto piston seat retainer. Torque to 200 in./lbs. Remove piston assembly from vice.

33. Place cylinder in vice using wrench flats and tighten.

34. Soak new leather packings in linseed oil for 5 minutes. Do not oversoak.

35. Insert wave spring (9) and lower male adapter (11) into cylinder. Remove leather packings from oil. Install leather packings (13) alternatively with UHMWPE packings (12). Insert lower female adapter (14).

36. Insert piston assembly into bottom of cylinder (8). A slight force may be required to push piston rod through packings.

37. Place O-Ring (27), lower ball seat (26), ball cage (25), ball (24) and lower ball stop disc (23) into inlet valve holder (28).

38. Put anti-seize compound on lower threads of cylinder (8). Put O-Ring (22) on cylinder. Loosen vise and tilt cylinder assembly at about a 45 degree angle. Tighten vise again.

39. Tighten foot valve holder assembly onto cylinder with an appropriate adjustable wrench until cylinder bottoms out in foot valve holder. Make sure to use wrench flats on foot valve holder to tighten completely. Torque to 40 ft./lbs.

40. Soak remaining new leather packings in linseed oil for 5 minutes. Do not oversoak.

41. Insert wave spring (6), upper male adapter (5). Remove leather packings from oil. Install leather packings (4) alternatively with UHMWPE packings (3). A tool, Wagner part #06009, may be required to compress packings down. Insert female adapter (2).

42. Install packing nut (1) and tighten until the nut bottoms out in cylinder. Torque to 25 ft./lbs. Do not over- tighten.

43. Install large locknut (7) onto upper cylinder (8) and turn until nut bottoms out on threaded section of cylinder.

44. Put anti-seize compound on upper cylinder threads. 45. Remove fluid section from vice and install into main

pump housing. Piston rod (10) will align itself inside yoke.

46. Rotate fluid section slightly to align hole in yoke and hole in piston assembly. Insert connecting pin. Replace spring retainer.

47. Thread fluid section into pump housing completely, then unscrew up to 3/4 turn to align outlet elbow with fluid hose.

48. Rotate large locknut (7) clockwise until tight against drive housing.

CAUTION Do not over tighten or damage to cylinder may occur.

CAUTION Hold hand under piston rod (10). Damage can occur if piston rod

falls to the floor. Lower packings may also fall out.

16

NEVER OPERATE PUMP WITHOUT FRONT COVER IN PLACE.

WARNING

Brushes should be inspected periodically to insure uninter- rupted service. Their life depends on speed as well as load.

If one of the brushes measures less than 1/4'' or is worn roughly or chipped, replace both motor brushes. It is also recommended that brushes be checked when packings are replaced.

1. Disconnect power cord from electrical supply. 2. Remove the four (4) motor shroud mounting screws

and remove the motor shroud. 3. Unscrew and remove brush caps holding brushes in

place.

4. Remove brushes. 5. Replace with new brushes.

Brush Cap

Motor Brush

6. Replace brush caps. 7. Replace motor shroud and screws.

Figure 15. Remove Brush Cap and Motor Brush

Motor Brush Replacement

17

PROBLEM CAUSE REMEDY Unit will not run Blown panel fuse or tripped Check and replace/reset

breaker Unit not plugged in Plug in Pressure control knob set too low Turn knob to higher pressure Faulty or loose wiring Inspect/Take to SprayTech Authorized Service

Center Worn motor brushes Check and replace brushes Clogged Tip or Filters Clean tip and filters. Faulty On/Off switch fuse Take to SprayTech Authorized Service Center

Unit will not prime Dried out piston packings Remove siphon tube and feel lower ball check to be sure it is free to move off its seat. Place full cup of paint thinner over end of fluid section and turn on pump.

Pump inlet screen plugged Remove and clean. Air in pump or hose Hold gun trigger in open position and run unit

about 10 seconds until air is purged Check for siphon tube leak

Packings worn Replace packings. (See page 14) Fluid is too viscous Prime pump with compatible solvent. Bring pump

up to pressure. Carefully remove pump from solvent container and immerse inlet tube in heavy material to be sprayed. With nozzle tip removed, trigger gun until heavy material appears at gun. Replace nozzle tip.

Siphon tube clogged Remove and clean Siphon tube air leak Check connection and seal Clogged tip Relieve pressure, remove tip and clean.

Unit will not build or Pressure adjusting knob not Adjust to increase pressure maintain pressure properly set

Pump inlet strainer dirty Clean Valve balls or seals worn or dirty Replace or clean Air in pump or hose Hold gun trigger in open position and run about 10

seconds until air is purged Packings worn Replace (See Page 14) Worn spray tip Replace (Follow direction supplied with gun) Internal leakage With gun trigger closed, allow unit to pump up to

pressure and shut off if pump momentarily starts. Internal leak is indicated and fluid section rebuild is necessary. (See Page14)

Fluid leak Check for external leaks including hydraulic fittings attached to pressure control housing

Fluid too viscous Consult manufacturers recommendations on paint container label

Spray tip too large Change tip

Fluid leakage at upper Upper packing worn Relieve pressure and tighten packing take up nut end of fluid section or replace packings. (See Page 14)

Piston rod worn Replace. (See Page 14)

TROUBLESHOOTING

18

TROUBLESHOOTING CONTINUED

PROBLEM CAUSE REMEDY

Poor spray pattern Tip too large Change to smaller tip Pressure adjustment wrong Adjust pressure control knob Insufficient fluid delivery Clean all strainers and filters Fluid too viscous Add solvent according to manufacturer's

recommendations

Unit lacks power Pressure adjustment low Increase pressure Improper voltage supply Reconnect input voltage for 115 AC

Blow Fuses at Pump Excessive pressure Take to SprayTech Authorized Service Circuit Breaker Center Overtightened packings Repair/replace malfunctioning parts gear box, linkage or motor failures

19

11

19 20

1

2

3 4

5 6

6 7 89

10

10 9

2

12 13

1514

16

17

18

21

22

23

24

25

20

26

Figure 16- EP2300 Final Assembly

ITEM PART NO. DESCRIPTION QTY

1 0294611 Hose, Fluid,1/4 NPT 1 2 05045 Nipple 2 3 - - - - - - - - Cart Assembly 1

(See Figure 18) 4 0294220 Filter/Dump Valve Assembly 1

(See Figure 26) 0294229 Optional Filter Assembly

(Includes Items 2, 4, 5, 6 & 7) 5 02518 Nipple 1 6 51055 Plug, Pipe 2 7 9885563 Fitting, Tube 1 8 0294416 Tube, Return 1 9 51357 Washer, Lock 4

10 52183 Bolt, Hex. Head 4 11 13549 Hose, Fluid 1 12 12440 Elbow, 90 1 13 0294415 Manifold 1

ITEM PART NO. DESCRIPTION QTY

EP2300 FINAL ASSEMBLY - FIGURE 16

14 9885547 Elbow 45 1 15 02208 Transducer Assembly 1

(See Figure 22) 16 02975 Strainer 1 17 0279473 Siphon Tube Assembly 1 18 0294584 Return Tube Clamp 1 19 0294393 Cover, Packing Nut 1 20 9802515 Screw 6 21 0294425 Cover, Front 1 22 9802511 Screw 5 23 0294133 Fluid Section Assembly 1

(See Figure 21) 24 ------------ Drive Assembly, 23 Series 1

(See Figure 25) 25 0294344 Baffle 1 26 0294405 Shroud, Motor 1

20

Figure 17- Low Boy Final Assembly

EP2300 LOW BOY FINAL ASSEMBLY - FIGURE 17 ITEM PART NO. DESCRIPTION QTY.ITEM PART NO. DESCRIPTION QTY.

1 - - - - - - - - LowBoy Cart Assembly 1 (See Figure 19)

2 51357 Washer, Lock 4 3 52183 Bolt, Hex. Hex. 4 4 13549 Hose, Fluid 2 5 05045 Nipple 2 6 51055 Plug, Pipe 2 7 02518 Nipple 1 8 0294220 Filter/Dump Valve Assembly 1

(See Figure 26) 0294228 Optional Filter Assembly

( Includes Items 5, 6, 7, 8, & 9) 9 9885559 Elbow, 90, Return Line 1

10 0294424 Tube, Return 1 11 9885547 Elbow, 45 1 12 02208 Transducer Assembly 1

(See Figure 22)

13 12440 Elbow, 90 1 14 0294415 Manifold 1 15 0090447 Elbow, 90 1 16 0294133 Fluid Section Assembly 1

(See Figure 21) 17 0294393 Cover, Packing Nut 1 18 9802515 Screw 6 19 0294425 Cover, Front 1 20 0294185 Suction Set 1

(See Figure 23) 21 9802511 Screw 5 22 - - - - - - - Drive Assembly 23 Series 1

(See Figure 25) 23 0294344 Baffle 1 24 0294405 Shroud, Motor 1

1

2 3

2 3

4

4

6 7

65 89

10

13 14

15

17 1819

20

21

22

23

18

24

5

11

12

16

21

Figure 18 - Cart Assembly

CART ASSEMBLY - FIGURE 18 ITEM PART NO. DESCRIPTION QTY. ITEM PART NO. DESCRIPTION QTY.

6 9890104 Cap, Axle 2 7 54458 Screw 2 8 13538 Bumper 2

0294534 Spacer, Wheel (NOT SHOWN) 4

7

8

6

5

4

3

2

1

1 0279324 Handle 1 2 9802518 Bolt 2 3 0288661 Knob 2 4 0294558 Frame, Cart 1 5 0270318 Wheel

22

LOWBOY CART ASSEMBLY - FIGURE 19 ITEM PART NO. DESCRIPTION QTY. ITEM PART NO. DESCRIPTION QTY.

Figure 19- LowBoy Cart Assembly

1

1 0294445 Handle, Cart 1 2 9802518 Bolt, Carriage 2 3 0288661 Knob, Handle 2 4 0294534 Spacer, Wheel 4

5 0270318 Wheel 2 6 9890104 Cap, Hub 2 7 0294579 Cart 1 8 0270343 Foot, Rubber 2

2

3

4 5 4

6

7

8

23

PRESSURE CONTROL ASSEMBLY - FIGURE 20 Item Part No. Description Qty.Item Part No. Description Qty.

Figure 20 - Pressure Control Assembly

1

2

8

5

12

11 13

10

20

19

16

17

18

21

14

15

7

1 0294837 Pressure Increase Label 1 2 0295426 Knob 1 3 02585 Toggle Boot 1 4 0089986 On/Off plate 1 5 0294349 Housing 1 6 0275703 Strain relief 1

9850630 Strain relief (CSA) 7 52671 Ring terminal 1 8 0294428 Cord set 1

02491 Cord Set (CSA) 1 9 9850629 Strain relief 1

10 02712 Spring 1 11 0294359 Plunger 1

3

6

4

9

12 02208 Transducer assy. 1 (See Figure 23)

13 9822522 Retainer ring 1 14 03662 Switch spacer 1 15 0294132 Pressure Switch Assembly 1 16 9800604 Screw 2 17 9851311 Lead wire 1 18 53280 On/Off switch 1 19 53732 Fuse (10 amp) 1 20 18066 Relay (25 amp) 1 21 50520 Screw 3

24

Figure 21 - Fluid Section

NOTE: #20 Torque 250 IN. LBS.

NOTE: #28 Torque 40 FT. LBS.

REPAIR KITS KIT NO. DESCRIPTION

0294905 Packing Kit (* Items Included)

0294689 Valve Kit (# Items Included)

*2

*4

*14

ITEM PART NO DESCRIPTION QTY.

1 0294319 Packing nut 1 2 0294377 Adapter 1 3 08180 Packings, UHMWPE 3 4 00078 Packings, leather 2 5 0294376 Upper male adapter 1 6 0294379 Wave spring 1 7 00302 Locknut 1 8 0294318 Cylinder 1 9 13364 Wave spring 1

10 0294316 Piston rod 1 11 0294326 Lower male adapter 1 12 08070 Lower packings, UHMWPE 3 13 09091 Lower packings, leather 2 14 0294375 Lower female adapter 1 15 13458 Upper ball stop disc 1 16 13357 Upper ball cage 1 17 50164 Upper ball 1 18 13359 Upper ball seat 1 19 09446 Washer 1 20 13481 Piston seat retainer 1 21 13482 Jam nut 1 22 13381 O-ring 1 23 13380 Lower ball stop disc 1 24 51519 Lower ball 1 25 00311 Lower ball cage 1 26 00310 Lower ball seat 1 27 00203 O-ring 1 28 13403 Inlet valve holder 1

0294133 FLUID SECTION ASSEMBLY FIGURE 21

NOTE: #1 Torque 25 FT. LBS.

NOTE: #21 Torque 200 IN./LBS.

1

*3

28

*#27

25

*#24

23 *#22

21

20

#18 *#17

16 15

*13 *12

*11

10

*9

8

7

*6 *5

*#19

# 26

25

Figure 22 - Transducer Assembly

TRANSDUCER ASSEMBLY - FIGURE 22

3

2

1

4

5

6

7

8

0294185 SUCTION SET ASSEMBLY - FIGURE 23

ITEM PART NO. DESCRIPTION QTY

1 0090447 Elbow 1 2 13455 Fitting, Hose 1 3 53635 Clamp, Hose 1 4 0294426 Hose, Siphon 1 5 02975 Strainer 1 6 13463 Tube, Siphon 1 7 0294424 Hose, Return 1

Figure 23 - Suction Set Assembly

7

6

5 4 3

2

1

ITEM PART NO. DESCRIPTION QTY

1 50431 Retainer ring 1 2 50504 O-ring 1 3 02216 Transducer body 1 4 02232 Piston 1 5 50512 Back-up ring 1 6 50482 O-ring - Standard material 1

02305* O-Ring - Lacquer based material 1

7 50423 Retainer ring 1

8 02283 Transducer Packing Kit Includes Items 1, 2, and 4 through 7.

* Optional - for lacquer based material

NOTE: When paint begins to leak through the weep hole on the transducer assembly, repack the transducer assembly.

26

EP2300 MOTOR ASSEMBLY - FIGURE 24

ITEM PART NO. DESCRIPTION QTY.

1 01678 Brush Holder 2 2 01694 Motor Brush 2 3 01686 Brush Cap 2 4 01783 Stud 2 5 19498 Stator Assy. 1 6 50148 #10 Lockwasher 4 7 50865 10-32 Nut 4 8 01791 Belleville Washer 4 9 50962 Bearing-Commutator End 2

10 *01961 Armature w/Bearings 1

* Includes #50962 Bearing

7

6

10

9

9

4

5

6

7

8

6

7

1

2 3

EP2300 Motor Assembly - Figure 24

NOTE: Washers must be stacked as shown.

8

27

EP2300 Drive Assembly - Figure 25

3

1 2

4 5

7 8 9

6 7

10

6

11

12

1314 15

16

17 18

19 20

21 22

23

24

25

26 27

28

29

30 31

32 33

34

35 36

37 38

39 40

ITEM PART NO. DESCRIPTION QTY.ITEM PART NO. DESCRIPTION QTY.

1 0294349 Housing 1 2 05304 Key 1 3 11177 Crankshaft 1 4 51837 Bearing 1 5 51845 Ring, Retainer 1 6 11843 Washer 2 7 53074 Screw 2 8 05282 Gear 1 9 50547 Bearing 1

10 0294154 Motor with Pinion 1 11 50318 Screw 13

50113 Washer 13 12 05208 Gear Set 1 13 05207 Pinion 1 14 50717 Spring Pin 1 15 19015 Gear Case 1 16 17183 Gasket 1 17 50989 Bearing 1 18 05223 High Speed Cluster 1 19 50997 Bearing 1 20 50008 Ball, Stainless 1

21 50962 Bearing 1 22 05274 Low Speed Cluster 1 23 50954 Bearing 1 24 53074 Screw 6

Washer, Lock 6 25 0294402 Plate, Adapter 1 26 0294365 Pin, Yoke 1 27 0294394 Gasket 1 28 0294301 Retainer. Spring 1 29 0294302 Pin, Connecting 1 30 51187 Ring, Retainer 2 31 0294606 Yoke 1 32 0294366 Bearing 1 33 0294367 Bearing 2 34 0294364 Bushing 1 35 50555 Bearing 1 36 0294604 Rod, Connecting 1 37 0294410 Bolt, Shoulder 1 38 0294368 Bearing 1 39 0294602 Drag Line 1 40 0294446 Washer 1

EP2300 DRIVE ASSEMBLY - FIGURE 25

28

1

2

3

4 5

6 7 8

9

0294220 DUMP VALVE ASSEMBLY - FIGURE 26 ITEM PART NO. DESCRIPTION QTY. ITEM PART NO. DESCRIPTION QTY.

1 0294194 Filter Body Assembly 1 2 14069 Filter Sieve (50 Mesh) 1

14068 Filter Sieve (100 Mesh) (OPTIONAL)

3 9894245 Support, Filter 1 4 14072 O-Ring 1

Figure 26 - Dump Valve Assembly

5 0294555 Head, Filter/Dump Valve 1 6 0294499 Seal, Dump Valve 1 7 0294516 Seat, Valve 1 8 9841502 Ball, 10mm 1 9 0294214 Dump Valve Cartridge 1

NOTES:

1

Torque to 35 Ft./Lbs. CAUTION: Be sure the handle is turned all the way counterclockwise2

Apply antisieze (P/N 0093930) to threads when reassembled.

1 2

when reassembled. Valve seat (item 6) will be damaged if it is not.

29

Item Part No. Description Qty.

DUMP VALVE ASSEMBLY - FIGURE 27

Figure 27 - Dump Valve Assembly

Item Part No. Description Qty.

1

2 3

4 5

1 0294502 Housing, Dump Valve 1 2 0294966 Repair Kit 1 3 0294499 Seal, Dump Valve 1

4 0294516 Seat, Valve 1 5 9841502 Ball, 10mm 1 6 0294214 Dump Valve Cartridge 1

6

1 2See Note Page 28{

Figure 28 - Dump Valve Cartridle

Item Part No. Description Qty. Item Part No. Description Qty.

DUMP VALVE CARTRIDGE - FIGURE 28

5 0294501 Washer, Dump Valve 1 6 9822516 Ring, Retainer 1 7 0294788 Washer, Kit, Bellville 4 8 0291512 Handle, Dump Valve 1

1 9871046 O-Ring 1 2 0294498 Body, Dump Valve 1 3 9871045 O-Ring 1 4 0294500 Stem, Dump Valve 1

1

2

3 4

5 6

7

8

Convex

Concave Convex

30

ACCESSORIES

GUN FILTERS

Part Number Description

0153 Tungsten Carbide Flat Tips 0153003 Tip Guard, Flat Tip 0291004 Hose, Whip End, 3' x 3/16" 0291003 Hose, Whip End, 5 x 3/16 0291002 Hose, Wireless, 25 x 1/4" 0291000 Hose, Wireless, 50 x 1/4" 0093896 Hose Connector, 1/4 x 1/4M 0088154 Pressure Gauge 0153043 Tip Extension, 6 (fits 11/16 diffuser) 0153042 Tip Extension, 12 (fits 11/16 diffuser) 0152001 Power Roller Gun Attachment 0152308 9" Roller Cover, 3/8 Nap 0152307 9" Roller Cover, 1/2 Nap 0152309 9" Roller Cover, 3/4 Nap 0152310 9" Roller Cover, 1-1/4 Nap 0152235 12" Roller Cover, 1/2" Nap 0152236 12" Roller Cover, 3/8" Nap 0152237 12" Roller Cover, 3/4" Nap 0152238 12" Roller Cover, 1-1/4" Nap 0152700 Adapter, Power Roller Extension 0149017 G-10 Four Finger Airless Spray Gun (no tip) 0093930 Anti-Seize Compound 0152909 R-10 Telescoping Roller, 9", 3/8" Nap 0152900 R-10 Telescoping 12" Roller, 3/8" Nap 0502007 G-10 Four Finger Airless Spray Gun with 517

Reversible Tip 0502008 G-10 Two Finger Airlesss Spray Gun (no tip) 0502009 G-10 Two Finger Airless Spray Gun with 517

Reversible TIp 0270214 G-10 Four Finger Spray Pack with 50 x 1/4

airless hose 0502012 G-10 Two Finger Spray Pack with 50 x 1/4

Airless Hose

Mesh Number

0.084 mm

0.140 mm

0.315 mm

0.560 mm

Part No.

0089960

0089959

0089958

0089957

Application

Synthetic resin enamels, clean varnishes, stains azures

Base coat enamels primer enamels fillers, marking paints, textujred enamesls

Emulsions Latex-paints acrylic-paints

Filler paints, large area surfaces

Filter Type

Extrafine

Fine

Medium

Coarse

Color of Fiilter Body

Red

Yellow

Green

White

32

Two Year Warranty Spray Tech, a division of Wagner Spray Tech Corporation ("Spray Tech"), warrants this product against defects in material and workmanship for a period of two years following the date of purchase by the original purchaser. During that period, Spray Tech will repair or replace any defective or worn-out component or, at Spray Techs option, refund to the original purchaser the full purchase price for the product in exchange for the return of that product. However, Spray Tech will not replace or repair any fluid pump component on account of wear more than twice during the two year warranty period. This warranty does not cover consumable products such as filters and tips.

Lifetime Warranty on Gear Trains, Electric Motors, and Gas Engines Spray Tech warrants any gear train, electric motor (excluding brushes) and gas engine (excluding the clutch) in this product against defects in material and workmanship for the lifetime of the original purchaser. If Spray Tech determines that the foregoing warranty has been breached, Spray Tech will repair or replace the defective components without charge or, at Spray Techs option, refund to the original purchaser the full purchase price for the product in exchange for the return of that product.

Warranty Claims Any request for repair or replacement pursuant to the warranties above must be accompanied by the return of the applicable parts, with transportation charges prepaid, to a service center authorized by Spray Tech or to Wagner Spray Tech Corporation, 1770 Fernbrook Lane, Minneapolis, MN 55447.

Limitation of Remedies THE REMEDIES SET FORTH ABOVE ARE THE EXCLUSIVE REMEDIES AVAILABLE FOR BREACH OF EXPRESS AND IMPLIED WARRANTIES. These remedies shall not be deemed to have failed of their essential purpose so long as Spray Tech is willing to repair or replace parts, or to refund the purchase price, as set forth above.

What Is Not Covered By This Warranty This warranty does not cover defects or damages caused by:

the use or installation of repair or replacement parts or accessories not manufactured by Spray Tech; repair performed by anyone other than a Spray Tech Authorized Service Center; or abuse, misuse, negligence, accident, faulty installation or tampering in a manner which impairs normal operation.

This warranty also does not cover equipment and accessories supplied to Spray Tech from an original equipment manufacturer, including but not limited to hoses, tips, and accessories. Spray Tech will provide the purchaser with copies of the original equipment manufacturers express warranties provided to Spray Tech along with the name and address of the appropriate manufacturer.

Limitation of Remedies IN NO CASE SHALL SPRAY TECH BE LIABLE FOR ANY INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES OR LOSS, INCLUDING TRANSPORTATION COSTS, WHETHER SUCH DAMAGES ARE BASED UPON A BREACH OF EXPRESS OR IMPLIED WARRANTIES, BREACH OF CONTRACT, NEGLIGENCE, STRICT TORT, OR ANY OTHER LEGAL THEORY.

Disclaimer Of Implied Warranties THE FOREGOING WARRANTIES ARE IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.

No Ability To Transfer This warranty is extended to the original purchaser only and is not transferable.

Patents These products are covered by one or more of the following patents:

5,228,842 5,192,425 D344,832 5,318,314 5,282,722 5,099,183 5,346,037 5,494,199 5,472,318 5,435,697 4,992,633

Limited Warranty Commercial Airless Spray Equipment

Printed in U.S.A.

1770 Fernbrook Lane Minneapolis, Minnesota 55447 Telephone 1-800-292-4637

Manualsnet FAQs

If you want to find out how the EP2300 Titan works, you can view and download the Titan EP2300 0294036 Pump Owner's Manual on the Manualsnet website.

Yes, we have the Owner's Manual for Titan EP2300 as well as other Titan manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Owner's Manual should include all the details that are needed to use a Titan EP2300. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Titan EP2300 0294036 Pump Owner's Manual is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Titan EP2300 0294036 Pump Owner's Manual consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Titan EP2300 0294036 Pump Owner's Manual free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Titan EP2300 0294036 Pump Owner's Manual, simply download the document to your computer. Once downloaded, open the PDF file and print the Titan EP2300 0294036 Pump Owner's Manual as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.