Contents

Synology DVA3219 v14 Administrator's Guide PDF

1 of 16
1 of 16

Summary of Content for Synology DVA3219 v14 Administrator's Guide PDF

1

Based on

Synology Surveillance Station 8.2.8

Face Recognition Administrator's Guide for

Table of Contents

Introduction 01

Camera Quick Installation 02

Improve Detection Accuracy 04

Configure Software Settings 05

Search and Manage Recognition Results 10

01

Introduction

With its powerful AI Image Analysis, Synology Deep Video Analytics (DVA) can instantly

calculate large amounts of object attributes, filter out environmental interferences, and

deliver accurate detection results.

Among the supported algorithms, Face Recognition is designed to identify customers,

employees, or suspicious persons to deliver better services and enhance security.

For you to achieve optimal precision, this guide aims to introduce the key factors of setting

up Face Recognition tasks. For best results, please follow the listed points as closely as

possible.

System Requirements

Surveillance Station version 8.2.8 or later.

Synologys Face Recognition App (installed by default).

Note: No additional licenses required for Face Recognition App.

Introduction

02

Camera Quick Installation

Camera Quick Installation

Select Appropriate Camera Stream Quality 1920x1080@20 FPS or above

Optical Zoom Lens (Optional) Used to capture clearer facial images when pedestrians are far away

Dos and Donts

Reflective surfacesSufficient lighting Backlight Panoramic camera

Step 1

Check Installation Environment Minimum Illumination 300 lux

Installation Location/Direction Directly face the flow of pedestrians through the indoor entrance/exit to capture front-facing images

Indoor ExitIndoor Entrance

Step 2

03

Camera Quick Installation

Mounting Height and Angle Installation Height 1.5 ~ 3 meters

Camera Tilt Angle Less than 15 degrees

Face Resolution At least 75 75 pixels (ideally 125 125 pixels)

*The values provided are for reference only; please adjust the installation height/angle using actual camera configurations that can provide a clear face resolution.

Camera Tilt Angle

Pedestrians Distance

Installation Height

FOV Width

Face Resolution

Pedestrians Height

Dos and Donts

Tilted faces Partially covered faceClear facial features Overlarge tilt angle

Step 3

04

Improve Detection Accuracy

It is still possible that faces will not be detected or will be wrongly recognized even with

thorough planning of the camera placement and environment. The following situations can

affect detection and recognition by the AI:

Light shining directly into the camera's lens may leave streaks in the images or cause

overexposure, affecting the picture quality.

The camera installed in areas where drastic changes in lighting can happen can lead to

inconsistent picture quality.

Overexposed or underexposed facial images can impede recognition by the AI.

Backgrounds with yellowing lighting can impede recognition by the AI; white lighting is

recommended.

Pedestrians moving too fast might cause captured facial images to blur.

Changes in the cameras field of view might affect the video analytic results (e.g., changes in

focus or zoom level).

Weather sometimes affects the clarity of outdoor cameras. Rain and snow, changes of

shadows, or differences between day and night can have an impact on detection and

recognition.

An unstable network connection might lead to incomplete or corrupt images. Wired

connections are highly recommended.

Dust, insects, or other stains can block the lens. Keep the lenses clean so that a clear image

can be taken.

Improve Detection Accuracy

05

Configure Software Settings

Once your cameras are mounted successfully, you can configure software settings for the

Face Recognition App to suit your requirements. This chapter covers the essential settings for

the Face Recognition algorithm.

It is recommended to create a face database first before setting up a face recognition task.

However, if no previous database information is available, you can also set up a task and

create a face database organically from the ground up.

Create Face Database To identify and classify people into different types of events (Allowed, Blocked, VIP or

Registered), you need to create user profiles and user groups in Face Database before

adding a Face Recognition task. You can create user profiles one by one or import user data

and photos by batches.

Go to: Surveillance Station > Face Recognition App > Face Database

The most efficient way to build a face database is to import user profiles in batches. When

importing profiles in batches, the following options are available:

Import using a customized profile list

Import local DSM, domain, or LDAP users

Configure Software Settings

06

Improve Detection Accuracy

The following specifications are required for the import file (for either of the above import

options):

Account - Each account must be unique, between 1 - 128 characters, and include only

Unicode letters, numbers, or the following symbols: . - _ @ \

Photo File Name - Used to match the uploaded photo to the account.

Do not modify any cell contents before Row 3. Only the original XLSX format is accepted.

Note: You can also directly import groups or only import new users from DSM, domain, or LDAP.

Define Groups Users in the Face Database can be assigned to one or more groups. Groups can be created

either manually in the Face Database or by importing local DSM, domain, or LDAP users.

Once defined, groups can then be assigned to one of three events in a Face Recognition Task: allowed, blocked, VIP. This allows you to quickly filter out the identification outcomes

you are looking for among face recognition results and when viewing videos in Live View.

Face frame colors can be used to assigned to identify priority.

For example, if you want to check how many VIPs have appeared within a set period of time,

you can filter the event VIP in the Recognition Results. Or if you are watching a video in Live View, VIPs will be framed a specific color for quick recognition.

Note: Each group can only be assigned to one event. If user profiles or groups have been

assigned to multiple event lists, they will be marked in the order of Blocked > VIP > Allowed.

07

Improve Detection Accuracy

Improve Detection Accuracy For best recognition results, a good profile photo should have the following:

Make sure both the eyes and nose are visible and facing directly at the camera, not tilted

up, down, or sideways.

Use a photo taken within three months before creating the profile and update it regularly.

Photo resolution should be at least 300 300 pixels. The width of the face should be at

least 75 pixels.

Facial features should be clearly visible and not overexposed or underexposed.

Include the persons shoulders and some space above the top of the head.

Only PNG, JPG and BMP files formats are allowed.

Create Face Recognition Task A face recognition task can be created after a face database has been set up (this is

recommended but not a prerequisite). Only once a face recognition task has been created

can Live View recognize and categorize people from a stream.

Note: One DVA face recognition task can at most simultaneously detect and compare up to 25 faces in real-time.

Select a Stream Profile

For optimal detection accuracy, select a resolution of at least 1920x1080@20FPS

Registered and Unknown Events

For easy identification, a face frame color and groups can be assigned to pre-determined

events such as Allowed, Blocked, and VIP (for more information, please see Define Groups).

If no group is assigned, and a person is identified from the face database, the system will

categorize them as Registered. A frame color can similarly be assigned to Registered users

so that you can quickly filter out the identification outcomes you are looking for among face

recognition results and when viewing videos in Live View. Similarly, if faces are unrecognized,

unclear, or taken at a bad angle of view, a frame color can also be assigned for easy filtering.

08

Improve Detection Accuracy

Ignore Unclear Faces and Undersized Faces

For the sake of efficiency, you can fine-tune the minimum on-screen face size to filter

out false positives from unclear or undersized faces. In the Events tab, you can choose

to enable Ignore alerts that are triggered by unclear faces; when detected faces are

unclear or taken from a bad angle, an event alert will not be sent. Click the Edit button in the

Parameters tab to adjust the blue object frame to define the minimum on-screen face size.

(The percentage refers to the size of the face in relation to the camera image size.) Faces that

are smaller than the defined object size will be filtered out.

09

Improve Detection Accuracy

In the Recognition Results, you can also enable the Ignore Unclear Faces option. Faces

that are unclear or taken from a bad angle will be excluded from the results.

Face Recognition Mechanism

Face recognition works by comparing detected faces with the faces in the face database. A

detected face will be positively identified from the face database if the similarity between the

profile photo and the detected face exceeds the value specified in the Similarity parameter.

By default, the Similarity parameter is set to 80%.

Define the Detection Zone

Face Recognition App allows usage of two types of zones: Inclusive and Exclusive. An Inclusive

zone means that detection will occur within the defined zone. An Exclusive zone means

that detection will occur outside the defined zone. Both are highly compatible with various

scenarios, allowing you to cover the areas that truly matter.

Simply drag the nodes to adjust the position of the detection zone. You can left-click on the

zone border to add nodes or right-click on the nodes to delete them. The detection zone

should not be too thin or small; it should at least be two times the size of the face you want

to identify. Up to three zones on one screen can be configured.

10

Search and Manage Recognition Results

Search and Manage Recognition Results

Besides detailed configuration options, Face Recognition also offers two ways to view

and manage recognition results, one through Live View, and the other through the Apps

Recognition Results.

Monitor Recognition Results in Live View To be able to see recognition results in live view, a face recognition task must be set up, one

or more face recognition events configured as alert triggers, and the task added to the layout

as a source. (For more information on how to do this, please see Monitor Live Views.) Face

recognition results can be viewed in the Alert Panel. The filter can be further used to focus

on specific events, such as VIPs detected.

For example, you can choose to filter VIPs in the alert panel to see all instances where VIP

accounts appear.

Right-clicking on a face that has been labeled by a face recognition task will display more

options for that result (either identified or not). If the face is unidentified, the person can be

registered to the database using that snapshot, and you can also choose to identify similar

faces in unknown results as that person. If the face is identified (either as part of a group or

simply as registered), you can view personal information for that person available in the face

database, search by user profile or snapshot, correct the identification with another profile

from the face database, or mark the identification as unknown.

11

Search and Manage Recognition Results

Search Historical Recognition Results Go to: Surveillance Station > Face Recognition App > Recognition results

Face Recognition App allows you to filter recognition results by tasks, events, dates, or you

can search for a specific person among the results.

When searching for a specific person by profile information, you can search using the

name, account, or description, or you can search using an uploaded face image. Results,

if found, will show all the different times that a certain person has been detected by face

recognition. Specific results can be locked (so that it will not be deleted automatically through

archive retention policies) or downloaded for backup purposes. You can also correct the

misidentified results by marking the result as unknown or correcting the identification to

another user profile.

12

Search and Manage Recognition Results

If a person is not registered in the face database, you can also do an image search by

uploading a face image and searching for similar results using that image. Another option is

to directly search in Recognition results using the Search by snapshot option. The level of

similarity can be adjusted to broaden or narrow the search.

There might be situations where a face was not identified by the system, but there is still a

possibility of error by the system. If you search by name, account name, or description among

recognition results, you can compare the database photo of that person with recognition

results using a different similarity level from the original task. Clicking on Compare Faces will

bring you to Image Search where you can adjust the similarity level.

Covered Face Detection Face Recognition can detect whether a face mask is in use or not. Results can be filtered to

show all covered or uncovered faces, and an alert can be configured in Live View to notify

you when a person with a covered or uncovered face is detected.

For example, if a person with a face mask enters a bank, an alert can be configured so that

security personnel is notified to be vigilant.

13

Search and Manage Recognition Results

Improve Recognition Results Recognition results can be improved by using captured face images to do the following:

Create a new profile (if no previous face database exists, a new database can be built this

way).

Update face database by manually correcting the recognition result and replacing the

database photo of a recognized person with a captured face image.

Correct recognition results by resetting the target as a stranger (mark as unknown) if face

recognition has wrongly identified the target.

14

Search and Manage Recognition Results

synology.com

Synology may make changes to specifications and product descriptions at any time, without notice. Copyright 2020 Synology Inc. All rights reserved. Synology and other names of Synology Products are proprietary marks or registered trademarks of Synology Inc. Other products and company names mentioned herein are trademarks of their respective holders.

SYNOLOGY INC.

9F, No. 1, Yuan Dong Rd. Banqiao, New Taipei 22063

Taiwan Tel: +886 2 2955 1814

SYNOLOGY AMERICA CORP.

3535 Factoria Blvd SE, Suite #200, Bellevue, WA 98006

USA Tel: +1 425 818 1587

SYNOLOGY FRANCE

102 Terrasse Boieldieu (TOUR W) 92800 Puteaux

France Tel: +33 147 176288

SYNOLOGY GMBH

Grafenberger Allee 125 40237 Dsseldorf

Deutschland Tel: +49 211 9666 9666

SYNOLOGY SHANGHAI

200070, Room 201, No. 511 Tianmu W. Rd., Jingan Dist., Shanghai,

China

SYNOLOGY UK LTD.

Unit 5 Danbury Court, Linford Wood, Milton Keynes, MK14 6PL,

United Kingdom Tel.: +44 (0)1908048029

SYNOLOGY JAPAN

Manualsnet FAQs

If you want to find out how the DVA3219 Synology works, you can view and download the Synology DVA3219 v14 Administrator's Guide on the Manualsnet website.

Yes, we have the Administrator's Guide for Synology DVA3219 as well as other Synology manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Administrator's Guide should include all the details that are needed to use a Synology DVA3219. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Synology DVA3219 v14 Administrator's Guide is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Synology DVA3219 v14 Administrator's Guide consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Synology DVA3219 v14 Administrator's Guide free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Synology DVA3219 v14 Administrator's Guide, simply download the document to your computer. Once downloaded, open the PDF file and print the Synology DVA3219 v14 Administrator's Guide as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.