Stihl HL-KM v2 Instruction Manual PDF

1 of 48
1 of 48

Summary of Content for Stihl HL-KM v2 Instruction Manual PDF

STIHL HL-KM

WARNING Read Instruction Manual thoroughly before use and follow all safety precautions improper use can cause serious or fatal injury.

ADVERTENCIA Antes de usar la mquina lea y siga todas las precauciones de seguridad dadas en el manual de instrucciones el uso incorrecto puede causar lesiones graves o mortales.

Instruction Manual Manual de instrucciones

Instruction Manual 1 - 21 Manual de instrucciones 22 - 44

O rig

in al

In st

ru ct

io n

M an

ua l

Pr in

te d

on c

hl or

in e-

fre e

pa pe

r Pr

in tin

g in

ks c

on ta

in v

eg et

ab le

o ils

, p ap

er c

an b

e re

cy cl

ed .

A

N D

R EA

S ST

IH L

AG &

C o.

K G

, 2 02

0 04

58 -4

75 -8

62 1-

E. V

A0 .J

20 .

English

Contents

00

74 90

_0 13

_G B

Allow only persons who fully understand the manuals of the KombiEngine and hedge trimmer KombiTool to operate this power tool combination.

To receive maximum performance and satisfaction from your STIHL KombiTool, it is important that you read, understand and follow the safety precautions and the operating and maintenance instructions in chapter "Safety Precautions and Working Techniques" before using your KombiTool. For further information you can go to www.stihlusa.com.

Contact your STIHL dealer or the STIHL distributor for your area if you do not understand any of the instructions in the two manuals.

WARNING

Because a KombiEngine equipped with a hedge trimmer KombiTool has a high- speed cutting attachment some special safety precautions must be observed to reduce the risk of personal injury. Careless or improper use may cause serious or even fatal injury.

KombiSystem 2 Guide to Using this Manual 2 Safety Precautions and Working Techniques 3 Using the Unit 9 Approved KombiEngines 11 Mounting the KombiTool 11 Assembling the Unit 12 Adjusting the Cutter Bar 13 Fitting the Harness 14 Starting / Stopping the Engine 15 Lubricating the Gearbox 16 Storing the Machine 17 Maintenance and Care 17 Sharpening Instructions 17 Main Parts 18 Specifications 19 Maintenance and Repairs 19 Disposal 20 Trademarks 20

00 00

HL-KM 1

This instruction manual is protected by copyright. All rights reserved, especially the rights to reproduce, translate and process with electronic systems.

English

In the STIHL KombiSystem a number of different KombiEngines and KombiTools can be combined to produce a power tool. In this instruction manual the functional unit formed by the KombiEngine and KombiTool is referred to as the power tool.

Therefore, the separate instruction manuals for the KombiEngine and KombiTool should be used together for the power tool.

Always read and make sure you understand both instruction manuals before using your power tool for the first time and keep them in a safe place for future reference.

Pictograms

All the pictograms attached to or embossed on the machine are shown and explained in this manual.

Symbols in Text

Many operating and safety instructions are supported by illustrations.

The individual steps or procedures described in the manual may be marked in different ways:

N A bullet marks a step or procedure.

A description of a step or procedure that refers directly to an illustration may contain item numbers that appear in the illustration. Example:

N Loosen the screw (1).

N Lever (2) ...

In addition to the operating instructions, this manual may contain paragraphs that require your special attention. Such paragraphs are marked with the following symbols and signal words:

DANGER

Indicates a hazardous situation that, if not avoided, will result in death or serious injury.

WARNING

Indicates a hazardous situation that, if not avoided, could result in death or serious injury.

NOTICE Indicates a risk of property damage, including damage to the machine or its individual components.

Engineering Improvements

STIHLs philosophy is to continually improve all of its products. As a result, engineering changes and improvements are made from time to time. Therefore, some changes, modifications and improvements may not be covered in this manual. If the operating characteristics or the appearance of your machine differs from those described in this manual, please contact your STIHL dealer or the STIHL distributor for your area for assistance.

KombiSystem Guide to Using this Manual

HL-KM2

English

Have your STIHL dealer show you how to operate your power tool. Observe all applicable local safety regulations, standards and ordinances.

WARNING

Do not lend or rent your power tool without the instruction manuals of your KombiEngine and KombiTool. Be sure that anyone using it understands the information contained in these manuals.

WARNING

The use of this machine may be hazardous. If the cutting tool comes in contact with your body, it will cut you.

Use your KombiEngine equipped with the hedge trimmer KombiTool only for cutting hedges, shrubs, scrub, bushes and similar material.

WARNING

Do not use it for other purposes, since misuse may result in personal injury or property damage, including damage to the machine.

WARNING

Minors should never be allowed to use this power tool. Bystanders, especially children, and animals should not be allowed in the area where it is in use.

WARNING

To reduce the risk of injury to bystanders and damage to property, never let your power tool run unattended. When it is not in use (e. g. during a work break), shut it off and make sure that unauthorized persons do not use it.

Most of these safety precautions and warnings apply to the use of all STIHL hedge trimmers. Different models may have different parts and controls. See the appropriate section of your KombiEngine and KombiTool instruction manuals for a description of the controls and the function of the parts of your model.

Safe use of a power tool involves

1. the operator

2. the power tool

3. the use of the power tool.

THE OPERATOR

Physical Condition

You must be in good physical condition and mental health and not under the influence of any substance (drugs, alcohol, etc.) which might impair vision, dexterity or judgment. Do not operate this machine when you are fatigued.

WARNING

Be alert if you get tired, take a break. Tiredness may result in loss of control. Working with any power tool can be strenuous. If you have any condition that might be aggravated by strenuous work, check with your doctor before operating this machine.

Proper Clothing

WARNING

To reduce the risk of injury, the operator should wear proper protective apparel.

Safety Precautions and Working Techniques

Because a KombiEngine equipped with a hedge trimmer KombiTool is a high-speed, fast-cutting power tool with sharp cut- ting blades, special safety precautions must be observed to reduce the risk of personal injury.

It is important that you read, fully understand and observe the following safety precautions and warnings. Read the instruction manuals and the safety precautions of your KombiEngine and KombiTool periodically. Careless or improper use may cause serious or fatal injury.

HL-KM 3

English

WARNING

Be particularly alert and cautious when wearing hearing protection because your ability to hear warnings (shouts, alarms, etc.) is restricted.

Avoid loose-fitting jackets, scarfs, neckties, jewelry, flared or cuffed pants, unconfined long hair or anything that could become caught on branches, brush or the moving parts of the unit. Secure hair so it is above shoulder level.

For further instructions on proper clothing see the safety precautions in the instruction manual of the KombiEngine you are using.

THE POWER TOOL (KOMBIENGINE EQUIPPED WITH HEDGE TRIMMER KOMBITOOL)

For illustrations and definitions of the power tool parts see the chapter on "Main Parts."

WARNING

Never modify this power tool in any way. Only attachments supplied by STIHL or expressly approved by STIHL for use with the specific STIHL KombiEngine are authorized. Although certain unauthorized attachments are useable with STIHL power tools, their use may, in fact, be extremely dangerous.

If this tool is subjected to unusually high loads for which it was not designed (e.g. heavy impact or a fall), always check that it is in good condition before continuing work. Check in particular that the controls and safety devices are working properly. Do not continue operating this machine if it is damaged. In case of doubt, have it checked by your STIHL servicing dealer.

THE USE OF THE POWER TOOL (KOMBIENGINE EQUIPPED WITH HEDGE TRIMMER KOMBITOOL)

Transporting the Power Tool

WARNING

To reduce the risk of injury from blade contact, never carry or transport your power tool with the cutting blades moving.

To reduce the risk of injury to your eyes never operate your power tool unless wearing goggles or properly fitted protec- tive glasses with adequate top and side protection complying with ANSI Z87 "+" (or your applicable national stand- ard). To reduce the risk of injury to your face STIHL recommends that you also wear a face shield or face screen over your goggles or protective glasses.

Wear an approved safety hard hat to reduce the risk of injury to your head when there is a danger of head injuries.

Power tool noise may damage your hearing. Wear sound barriers (ear plugs or ear mufflers) to protect your hearing. Continual and regular users should have their hearing checked regularly.

Always wear heavy duty work gloves (e.g. made of leather or other wear resistant material) when handling the machine and the cutting tool. Heavy-duty, nonslip gloves improve your grip and help to protect your hands.

Clothing must be sturdy and snug-fitting, but allow complete freedom of movement. Wear long pants made of heavy material to help protect your legs. Do not wear shorts, sandals or go barefoot.

Good footing is very important. Wear sturdy boots with nonslip soles. Steel-toed safety boots are recommended.

HL-KM4

English

WARNING

Always switch off the engine and fit the scabbard over the cutting blades before transporting the power tool over long distances.

It may be carried only in a horizontal position. Grip the shaft in a manner that the machine is balanced horizontally. Keep the hot muffler away from your body and the cutting attachment behind you.

WARNING

To reduce the risk of burn injury, do not touch hot parts of the machine and the gear housing when they are hot.

WARNING

When transporting it in a vehicle, properly secure it to prevent turnover, fuel spillage and damage to the unit.

On machines with an adjustable cutter bar: Make sure the cutter bar is secured in position. See chapter in this instruction manual entitled "Adjusting the Cutter Bar." On machines with a transport position: Move cutter bar to transport position and secure.

Before Starting

WARNING

Always check your power tool for proper condition and operation before starting. Never attempt to modify the controls or safety devices.

WARNING

Never operate your power tool if it is damaged, improperly adjusted or maintained, or not completely or securely assembled.

WARNING

The cutting attachment must be properly tightened and in safe operating condition. Inspect for loose parts (nuts, screws, etc.) and for cracked, bent, warped or damaged blades. Regularly check the condition of the cutting blades with the engine stopped! Replace damaged cutting blades before using the power tool. Always keep blades sharp.

Keep the handles clean and dry at all times; it is particularly important to keep them free of moisture, pitch, oil, fuel mix, grease or resin in order for you to maintain a firm grip and properly control your power tool.

STIHL recommends that you always spray the cutting blades with STIHL resin solvent before starting work with the engine stopped! You can obtain this protective spray from your dealer. Apply generously.

Adjust harness and hand grip to suit your size before starting work. To be better prepared in case of an emergency, practice releasing the unit from the harness as quickly as possible.

Starting

On machines with an adjustable cutter bar: Secure the cutter bar in the starting position as described in the chapter "Starting / Stopping the Engine." If this starting position is not the desired cutting position, you will then need to carefully adjust the machine to the desired position once the engine has returned to idle and the blades are no longer moving.

On machines with a defined transport position (cutter bar folded against the drive tube): Never start the machine in the transport position, since the blades are not engaged in that position and you therefore cannot visually check to see that they will be stopped at idle when you start to adjust the cutter bar to the desired cutting position (where the blades are engaged).

Start the engine at least 10 feet (3 m) from the fueling spot, outdoors only.

For specific starting instructions, see the appropriate section of your KombiEngine and KombiTool manuals.

Place the power tool on firm ground or other solid surface in an open area. Maintain good balance and secure footing.

WARNING

To reduce the risk of injury from loss of control, do not attempt to "drop start" your power tool.

00 2B

A2 54

K N

HL-KM 5

English

WARNING

To reduce the risk of injury from loss of control, be absolutely sure that the cutting tool is clear of you and all other obstructions and objects, including the ground, because when the engine starts at starting-throttle, engine speed will be fast enough for the clutch to engage and move the blades on the cutting tool.

Once the engine has started, immediately blip the throttle trigger, which should release the starting throttle and allow the engine to slow down to idle.

With the engine running only at idle, attach the power tool to the spring hook of your harness (see appropriate chapter of this manual).

WARNING

Your power tool is a one-person machine. Do not allow other persons in the general work area, even when starting.

See also the Safety Precautions on Starting in the instruction manual of the KombiEngine.

During Operation

Holding and Controlling the Power Tool

Always hold the unit firmly with both hands on the handles while you are working. Wrap your fingers and thumbs around the handles.

Models with loop handle

Right hand on control handle, left hand on loop handle on drive tube, even if you are left-handed. Wrap your fingers and thumbs around the handles.

Models with handle hose

Right hand on control handle, left hand on handle hose on drive tube, even if you are left-handed. Wrap your fingers and thumbs around the handles.

WARNING

WARNING

Do not overreach. Keep proper footing and balance at all times. Special care must be taken in slippery conditions (wet ground, snow) and in difficult, overgrown terrain. Watch for hidden obstacles such as tree stumps, roots and ditches to avoid stumbling. For better footing, clear away fallen branches, scrub and cuttings. Be extremely cautious when working on slopes or uneven ground.

WARNING

To reduce the risk of injury from loss of control, never work on a ladder, in a tree or any other insecure support. Never hold the machine above shoulder height.

Working Conditions

Operate and start your power tool only outdoors in a well-ventilated area. Operate it under good visibility and daylight conditions only. Work carefully.

00 00 -G X X -1 67 7- A 0

00 00 -G X X -1 67 8- A 0

Never attempt to operate your power tool with one hand. Loss of control of the power tool resulting in serious or fatal injury may result. To reduce the risk of cut injuries, keep hands and feet away from the cutting tool. Never touch a moving cutting tool with your hand or any other part of your body.

HL-KM6

English

WARNING

If the vegetation being cut or the surrounding ground is coated with a chemical substance (such as an active pesticide or herbicide), read and follow the instructions and warnings that accompanied the substance at issue.

WARNING

Substantial or repeated inhalation of dust and other airborne contaminants, in particular those with a smaller particle size, may cause respiratory or other illnesses. Control dust at the source where possible. Use good work practices, such as operating the unit so that the wind or operating process directs any dust raised by the power tool away from the operator. Follow the recommendations of EPA / OSHA / NIOSH and occupational and trade associations with respect to dust ("particulate matter"). When the inhalation of dust cannot be substantially controlled, i.e., kept at or near the ambient (background) level, the operator and any bystanders should wear a respirator approved by NIOSH / MSHA for the type of dust encountered.

Operating Instructions

WARNING

Do not operate your power tool using the starting throttle lock, as you do not have control of the engine speed.

In the event of an emergency, switch off the engine immediately move the slide control / stop switch / momentary stop switch to 0 or STOP.

See section of your KombiEngine instruction manual on the proper use of the slide control / stop switch / momentary stop switch.

WARNING

The cutting blades continue to move for a short period after the throttle trigger is released.

Accelerating the engine while the blades are blocked increases the load and will cause the clutch to slip continuously. This may result in overheating and damage to important components (e.g. clutch, polymer housing components) which can then increase the risk of injury from the blades moving while the engine is idling.

WARNING

On units with an adjustable cutter bar: Carefully adjust the cutter bar to the desired cutting position.To reduce the risk of injury, never touch the cutting blades while making adjustments. Only adjust the cutter bar when the blades are no longer moving.

The power tool has a large range. In order to reduce the risk of personal or even fatal injury to bystanders from falling objects or inadvertent contact with the moving cutting blades of your power tool always keep bystanders at least 17 feet (5 m) away when the power tool is running.

DANGER

Electricity can jump from one point to another by means of arcing. Higher voltage increases the distance electricity can arc. Electricity can also move through branches, especially if they are wet. Maintain a clearance of at least 50 feet (15 m) between the pole pruner (including any branches it is contacting) and any electrical line carrying live

Inhalation of certain dusts, especially organic dusts such as mold or pollen, can cause sus- ceptible persons to have an allergic or asthmatic reaction.

Your power tool is not insulated against electric shock. To reduce the risk of electrocution, never operate this power tool in the vicinity of any wires or cables (power, etc.) which may be carrying electric current.

17ft (5m)

50ft (15m )

HL-KM 7

English

current. Before working with less clearance, contact your electric utility and make sure the current is turned off.

Stop the engine immediately if you are approached.

WARNING

Before you start work, examine the hedge area for stones, glass, fence wire, metal, trash or other solid objects which could damage the cutting blades.

Take particular care when cutting hedges next to or against wire fences. Do not touch the wire with the cutting blades. When working close to the ground, make sure that no sand, grit or stones get between the cutting blades.

Striking solid foreign objects such as stones, fence wire or metal could damage the cutting attachment and may cause blades to crack, chip or break. STIHL does not recommend the use of your power tool when cutting in areas where the blades could contact such objects.

WARNING

Observe the cutting blades at all times do not cut any areas of the hedge that you cannot see. When cutting the top of a taller hedge, check the other side of the hedge frequently for bystanders, animals and obstructions.

WARNING

If the cutting tool becomes clogged or stuck, always shut off the engine and make sure the cutting tool has stopped

before cleaning. Grass, weeds, etc. should be cleaned off the cutting tool at regular intervals.

Check the cutting blades at regular short intervals during operation, or immediately if there is a noticeable change in cutting behavior:

Shut off the engine.

Wait until the cutting blades have come to a complete standstill.

Check condition and tightness, look for cracks.

Check sharpness.

Replace damaged or dull cutting tools immediately, even if they have only superficial cracks.

WARNING

MAINTENANCE, REPAIR AND STORING

WARNING

Always stop the engine and make sure that the cutting attachment is stopped before doing any maintenance or repair work or cleaning the power tool. Do not attempt any maintenance or repair work not described in your KombiEngine and KombiTool instruction manuals. Have such work performed at your STIHL servicing dealer only.

Always clean dust and dirt off the machine do not use any grease solvents for this purpose.

Spray the blades with STIHL resin solvent. Start and run the engine briefly so that the solvent is evenly distributed.

WARNING

Use only identical STIHL replacement parts for maintenance and repair. Use of non-STIHL parts may cause serious or fatal injury.

Wear gloves when handling or performing maintenance on blades.

WARNING

Never repair damaged cutting attachments by welding, straightening or modifying the shape. This may cause parts of the cutting attachment to come off and result in serious or fatal injuries.

Keep blades sharp. Tighten all nuts, bolts and screws, except the carburetor adjustment screws, after each use.

Do not clean your machine with a pressure washer. The solid jet of water may damage parts of the machine.

Store the power tool in a dry and high or locked location out of reach of children.

The gearbox becomes hot during operation. To reduce the risk of burn injury, do not touch the gear housing when it is hot.

HL-KM8

English

Cutting Season

Observe country-specific or municipal rules and regulations for cutting hedges.

Do not use your hedge trimmer during rest periods customary in the neighborhood.

Cutting Sequence

If a radical cut is necessary, cut a little at a time in several stages.

Use lopping shears to cut out thick branches first.

Cut the sides of the hedge first, then the top.

Disposal

Do not throw cuttings into the garbage can they can be composted.

Preparations

N Adjustable gearbox: Set cutter bar to required angle.

N Remove the blade scabbard.

N Start the engine.

N If you use a harness: Put on the harness and attach it to the machine.

Working Techniques

Horizontal Cut (with cutter bar at an angle)

Cutting close to the ground from a standing position, e.g. low shrubs.

Swing the cutter bar up and down as you move along the hedge use both sides of the cutting blades, do not rest the cutter bar on the ground.

Vertical Cut (with cutter bar at an angle)

Cutting without standing directly next to the hedge, e.g. flowerbed between operator and hedge.

Swing the cutter bar up and down in an arc as you move along the hedge use both sides of the cutting blades.

Using the Unit

38 8B

A0 29

K N

38 8B

A0 30

K N

HL-KM 9

English

Vertical Cut (with straight cutter bar)

Extra long reach without the need for other aids.

Swing the cutter bar up and down in an arc as you move along the hedge use both sides of the cutting blades.

Overhead Cut (with cutter bar at an angle)

Hold the hedge trimmer vertically and swing it in an arc to make maximum use of its reach.

WARNING

Any working position above head height is tiring. To minimize the risk of accidents, work in such positions for short periods only. Set angle of adjustable cutter bar to maximum so that the unit can be held in a lower, less tiring position (with shoulder strap) while still providing adequate reach.

Horizontal Cut (with straight cutter bar)

Hold the cutter bar at an angle of 0 to 10 as you swing the hedge trimmer horizontally.

38 9B

A 05

0 K

N

38 8B

A0 31

K N

38 8B

A0 32

K N

HL-KM10

English

Swing the cutter bar in an arc towards the outside of the hedge so that the cuttings are swept to the ground.

Recommendation: Only cut hedges that are no more than chest height.

KombiEngines

Only use KombiEngines supplied or explicitly approved by STIHL for use with the attachment.

This KombiTool may be operated only in combination with the following KombiEngines:

STIHL KM 56 R, KM 85 R, KM 91 R, KM 94 R, KM 111 R, KM 131 R, KMA 130 R, KMA 135 R

N Push the lug (1) on the drive tube into the slot (2) in the coupling sleeve as far as stop.

When correctly installed, the red line (3) (arrow point) must be flush with the end of the coupling sleeve.

N Tighten down the star knob (4) firmly.

Removing the KombiTool

N Reverse the above sequence to remove the drive tube.

38 8B

A0 33

K N

Approved KombiEngines Mounting the KombiTool

1

00 2B

A3 26

K N

2

3

00 2B

A3 27

K N

4

HL-KM 11

English

Removing the Potective Cap

If a cap is fitted on the end of the KombiTool's or basic power tools drive tube:

N Pull the protective cap off the end of the drive tube and keep it in a safe place.

If the plug comes out of the drive tube when you pull off the cap:

N Push the plug into the drive tube as far as stop.

Mounting the Gearbox

N Loosen the clamp screws (10).

N Push the gearbox (11) onto the drive tube (5), turn the gearbox (11) back and forth as necessary.

Once the end of the drive tube is inserted beyond the slot in the clamp (12):

N Push the gearbox (11) fully home as far as stop.

N Tighten down the clamp screws moderately.

N Line up the gearbox (11) with the powerhead.

N Tighten down the clamp screws firmly.

Assembling the Unit

41 3B

A 01

4 K

N 00

2B A2

48 K

N

11 1010

5

00 00 -G X X -1 68 1- A 0

11

12

00 00 -G X X -1 68 2- A 0

HL-KM12

English

Angle Adjuster - 145

The angle of th cutter bar can be adjusted upwards in 4 stages from 0 (straight) to 55, and downwards in 7 stages from 0 to 90 (right angle facing down). There are therefore 12 possible working positions.

WARNING

To reduce the risk of injury, carry out the adjustment only when the cutting blades are at a standstill engine at idle speed.

WARNING

The gearbox gets hot during operation. To reduce the risk of burn injury, do not touch the gearbox.

WARNING

To reduce the risk of injury, never touch the blades while making adjustments.

N Pull back the sliding sleeve (1) and use the lever (2) to adjust the joint by one or several holes.

N Release the sliding sleeve (1) and make sure the lock pin engages the quadrant (3).

Transport Position

The cutter bar can be folded flat against the drive tube and locked in position to save space during transportation.

WARNING

To reduce the risk of injury, always shut off the engine depress stop switch and fit the blade scabbard before

moving the cutter bar to the transport position or from the transport position to the normal working position.

WARNING

The gearbox gets hot during operation. To reduce the risk of burn injury, do not touch the gearbox.

Adjusting the Cutter Bar

00 00 -G X X -1 68 3- A 0

145

00 00 -G X X -1 68 4- A 0

3

2

1

00 00 -G X X -1 68 5- A 0

HL-KM 13

English

N Shut off the engine.

N Fit the blade scabbard.

N Pull back the sliding sleeve (1) and use the lever (2) to swing the joint upwards in direction of drive tube until the cutter bar is flat against the drive tube.

N Release the sliding sleeve (1) and make sure the lock pin engages the quadrant (3).

The type and style of the harness and carabiner (spring hook) depend on the market.

Shoulder Strap

N Put on the shoulder strap (1).

N Adjust the length of the strap so that the carabiner (2) is about a hands width below your right hip.

Full Harness

N Put on the full harness (1).

N Adjust the length of the strap so that the carabiner (2) is about a hands width below your right hip.

N Close the locking plate (3).

Attaching Machine to Harness

N Attach the carabiner (1) to the carrying ring (2) on the drive tube hold the carrying ring steady.

00 00 -G X X -1 68 6- A 0

1

2

3 Fitting the Harness

1

00 2B

A3 74

K N

2

1

00 2B

A3 07

K N

2

3

1

00 2B

A3 08

K N2

1 2

HL-KM14

English

Disconnecting Machine from Harness

N Press down the bar on the carabiner (1) and pull the carrying ring (2) out of the carabiner.

Throwing Off the Machine

WARNING

The machine must be quickly thrown off in the event of imminent danger. Practice removing and putting down the machine as you would in an emergency. To avoid damage, do not throw the machine to the ground when practicing.

Practice quickly detaching the power tool from the carabiner as described under "Disconnecting Machine from Harness".

If you are using a shoulder strap: Practice slipping the strap off your shoulder.

If you are using a full harness: Practice quickly opening the locking plate and slipping the harness straps off your shoulders.

Starting the Engine

Always follow the operating instructions for the KombiEngine and basic power tool.

N Place the machine on the ground so that it rests securely on the engine support and the gearbox.

N On models with an adjustable cutter bar: Set the cutter bar to the straight (0) position.

N Remove the blade scabbard.

To reduce the risk of accidents, check that the cutting blades are not touching the ground of any other obstacles.

N If necessary, rest the gearbox on a raised support (e.g. mound, brick or something similar).

N Make sure you have a firm footing, either standing, stooping or kneeling.

N Hold the machine with you left hand and press it down firmly do not touch the controls on the control handle see KombiEngine or basic power tool instruction manual.

NOTICE Do not stand or kneel on the drive tube.

WARNING

The cutting attachment may begin to move as soon as the engine starts. For this reason, blip the throttle after starting the engine returns to idling speed.

The starting procedure is now as described in the instruction manual of the KombiEngine or basic power tool you are using.

Stopping the Engine

N See KombiEngine or basic power tool instruction manual.

1

00 2B

A3 10

K N2

1 2

Starting / Stopping the Engine

00 2B

A 03

8 K

N 00

2B A

07 2

K N

HL-KM 15

English

Blade Drive Gear

Lubricate the blade drive gear with STIHL gear lubricant for hedge trimmers see "Special Accessories".

HL 0 version

Adjustable HL 145 version

N Check the lubricant level at regular intervals of about every 25 hours of operation. Unscrew the filler

plug (1) if no grease can be seen on the inside of the filler plug, screw the tube of grease into the filler hole.

N Squeeze up to 10 g (2/5 oz) grease into the gearbox.

NOTICE Do not completely fill the gearbox with grease.

N Unscrew the tube of grease from the filler hole.

N Refit the filler plug and tighten it down firmly.

Angle Drive Gear

Lubricate the angle drive gear with STIHL gear lubricant for hedge trimmers (special accessory).

Adjustable HL 145 version

N Check the lubricant level at regular intervals of about every 25 hours of operation. Unscrew the filler plug (2) if no grease can be seen on the inside of the filler plug, screw the tube of grease into the filler hole.

N Squeeze up to 5 g (1/5 oz) grease into the gearbox.

NOTICE Do not completely fill the gearbox with grease.

N Unscrew the tube of grease from the filler hole.

N Refit the filler plug and tighten it down firmly.

Lubricating the Gearbox

1

00 00 -G X X -1 68 7- A 0

1

00 00 -G X X -1 68 8- A 0

00 00 -G X X -1 68 9- A 0

2

HL-KM16

English

For periods of about 3 months or longer

N Clean the cutting blades, check condition and spray them with STIHL resin solvent.

N Fit the blade scabbard.

N If the KombiTool is removed from the KombiEngine and stored separately: Fit the protective cap on the drive tube to protect it from dust and dirt.

N Store the machine in a dry and secure location Keep out of the reach of children and other unauthorized persons.

The following intervals apply to normal operating conditions only. If your daily working time is longer or operating conditions are difficult (very dusty work area, etc.), shorten the specified intervals accordingly.

All accessible screws and nuts

N Check and retighten if necessary (not screws and nuts on cutting blades)

Cutting blades

N Visual inspection before starting work

N Resharpen as necessary

N Replace if damaged

Gearbox lubrication

N Check before starting work

N Replenish as necessary

Safety labels

N Replace illegible safety labels

When cutting performance and behavior begin to deteriorate, i.e. blades frequently snag on branches: Resharpen the cutting blades.

It is best to have the cutting blades resharpened by a dealer on a workshop sharpener. STIHL recommends a STIHL servicing dealer.

NOTICE Do not operate your machine with dull or damaged cutting blades. This may cause overload and will give unsatisfactory cutting results.

Storing the Machine Maintenance and Care Sharpening Instructions

HL-KM 17

English

1 Cutting Blades 2 Blade Drive Gear 3 Drive Tube 4 Angle Drive 5 Sliding Sleeve 6 Quadrant 7 Adjusting Lever 8 Blade Scabbard 9 Sleeve

Main Parts

2 8

4

1

5

7

4 3

2

47 5B

A0 08

K N

6

3

HL-KM18

English

Definitions

1 Cutting Blades Steel blades for cutting hedges and shrubs.

2 Blade Drive Gear Converts rotary movement of angle drive into reciprocating movement of cutting blades.

3 Drive Tube Encloses and protects the drive shaft between the coupling sleeve and gearbox.

4 Angle Drive Transmits rotary motion of drive shaft to the blade drive gear.

5 Sliding Sleeve Locks and unlocks the cutter bar adjusting mechanism.

6 Quadrant Locks the cutter bar in the required position.

7 Adjusting Lever Used to set cutter bar to the required angle.

8 Blade Scabbard Covers cutting blades when hedge trimmer is not in use.

9 Sleeve Locates drive tube in coupling sleeve.

Cutting blades

Weight

Users of this unit should carry out only the maintenance operations described in this manual. STIHL recommends that other repair work be performed only by authorized STIHL servicing dealers using genuine STIHL replacement parts.

Genuine STIHL parts can be identified by the STIHL part number, the { logo and, in some cases, by the STIHL parts symbol K. The symbol may appear alone on small parts.

For repairs of any component of this units air emissions control system, please refer to the air emissions systems warranty in this manual.

Specifications

Blade type: Double-sided Blade length: 500 mm

(19.685 in), 600 mm (23.622 in)

Tooth spacing: 34 mm (1.339 in)

Tooth height: 22 mm (0.866 in)

Sharpening angle: 45 to blade level

HL-KM 0 500 mm: 1.7 kg (3.7 lbs.) HL-KM 0 600 mm: 1.8 kg (4.0 lbs.) HL-KM 145 500 mm: 2.4 kg (5.3 lbs.) HL-KM 145 600 mm: 2.6 kg (5.7 lbs.)

Maintenance and Repairs

HL-KM 19

English

Observe all country-specific waste disposal rules and regulations.

STIHL products must not be thrown in the garbage can. Take the product, accessories and packaging to an approved disposal site for environment- friendly recycling.

Contact your STIHL servicing dealer for the latest information on waste disposal.

STIHL Registered Trademarks

STIHL

{

K

The color combination orange-grey (U.S. Registrations #2,821,860; #3,010,057, #3,010,058, #3,400,477; and #3,400,476)

AutoCut

FARM BOSS

iCademy

MAGNUM

MasterWrench Service

MotoMix

OILOMATIC

ROCK BOSS

STIHL Cutquik

STIHL DUROMATIC

STIHL Quickstop

STIHL ROLLOMATIC

STIHL WOOD BOSS

TIMBERSPORTS

WOOD BOSS

YARD BOSS

Some of STIHLs Common Law Trademarks

4-MIX

BioPlus

Easy2Start

EasySpool

ElastoStart

Ematic

FixCut

IntelliCarb

Master Control Lever

Micro

Pro Mark

Quiet Line

STIHL M-Tronic

Disposal

00 0B

A0 73

K N

Trademarks

TM

STIHL Injection

HL-KM20

English

STIHL OUTFITTERS

STIHL PICCO

STIHL PolyCut

STIHL PowerSweep

STIHL Precision Series

STIHL RAPID

STIHL SuperCut

TapAction

TrimCut

This listing of trademarks is subject to change.

Any unauthorized use of these trademarks without the express written consent of ANDREAS STIHL AG & Co. KG, Waiblingen is strictly prohibited.

HL-KM 21

espaol / EE.UU

Contenido

M anual de instrucciones original

Im preso en papel libre de cloro.

Las tintas contienen aceites vegetales, el papel es reciclable.

AN D

R EAS STIH

L AG & C

o. KG , 2020

0458-475-8621-E. VA0.J20.

0000007490_013_EA

Permita que solamente las personas que comprenden completamente la materia tratada en los manuales del motor KombiEngine y del cortasetos KombiTool manejen esta herramienta motorizada combinada.

Para obtener el rendimiento y satisfaccin mximos de la herramienta KombiTool de STIHL, es importante que lea, obedezca y comprenda las precauciones de seguridad y las instrucciones de uso y mantenimiento dadas en el captulo "Precauciones de seguridad y tcnicas de uso", antes de usar la KombiTool. Para informacin adicional, puede acudir a www.stihlusa.com.

Comunquese con el concesionario o distribuidor de STIHL si no se entiende alguna de las instrucciones dadas en los dos manuales.

ADVERTENCIA

Dado que este motor KombiEngine equipado con el cortasetos KombiTool tiene un accesorio de corte de gran velocidad, es necesario tomar medidas especiales de seguridad para reducir el riesgo de lesiones. El uso descuidado o inadecuado puede causar lesiones graves e incluso mortales.

Sistema KombiSystem 23 Acerca de este manual de instrucciones 23 Medidas de seguridad y tcnicas de manejo 24 Uso 31 Motores KombiEngine aprobados 33 Instalacin del KombiTool 33 Armado de la mquina 34 Ajuste de la barra de corte 35 Uso de la correa para hombro 36 Arranque / parada del motor 37 Lubricacin de la caja de engranajes 38 Almacenamiento de la mquina 39 Informacin para mantenimiento 39 Instrucciones de afilado 40 Componentes importantes 41 Especificaciones 42 Informacin de reparacin 42 Desecho 43 Marcas comerciales 43

HL-KM22

Este manual de instrucciones est protegido por derechos de propiedad intelectual. Todos los derechos reservados, especial- mente los derechos de reproduccin, traduccin y procesamiento con sistemas electrnicos.

espaol / EE.UU

Con el sistema KombiSystem de STIHL, varios motores KombiEngine y accesorios KombiTool pueden combinarse para formar una herramienta motorizada. En este manual de instrucciones la unidad formada por el motor KombiEngine y la herramienta KombiTool se identifica como la herramienta motorizada.

Por lo tanto, para esta herramienta motorizada es necesario usar juntos los manuales de instrucciones para el motor KombiEngine y la herramienta KombiTool.

Siempre lea y entienda los dos manuales de instrucciones antes de usar la herramienta motorizada por primera vez y guarde los mismos en un lugar seguro para referencia futura.

Pictogramas

Todos los pictogramas que se encuentran fijados o grabados en la mquina se muestran y explican en este manual.

Smbolos en el texto

Muchas de las instrucciones de uso y seguridad vienen acompaadas de ilustraciones.

Los pasos individuales o procedimientos descritos en el manual pueden estar sealados en diferentes maneras:

N Se usa un punto para denotar un paso o procedimiento.

Una descripcin de un paso o procedimiento que se refiere directamente a una ilustracin puede contener nmeros de referencia que aparecen en la ilustracin. Ejemplo:

N Suelte el tornillo (1).

N Palanca (2)...

Adems de las instrucciones de uso, en este manual pueden encontrarse prrafos a los que usted debe prestar atencin especial. Tales prrafos estn marcados con los smbolos y las palabras identificadoras:

PELIGRO

Identifica una situacin de peligro que, de no evitarse, causar lesiones graves o mortales.

ADVERTENCIA

Identifica una situacin de peligro que, de no evitarse, podra causar lesiones graves o mortales.

INDICACIN Indica el riesgo de daos a la propiedad, incluidos la mquina o sus componentes.

Mejoramientos tcnicos

La filosofa de STIHL es mejorar continuamente todos sus productos. Como resultado de ello, peridicamente se introducen cambios de diseo y mejoras. Por lo tanto, es posible que algunos cambios, modificaciones y mejoras no se describan en este manual. Si las caractersticas de funcionamiento o la apariencia de su mquina difieren de las descritas en este manual, comunquese con el concesionario STIHL para obtener la ayuda que requiera.

Sistema KombiSystem Acerca de este manual de instrucciones

HL-KM 23

espaol / EE.UU

Pida a su concesionario STIHL que le ensee el manejo de la herramienta motorizada. Respete todas las disposiciones, reglamentos y normas de seguridad locales del caso.

ADVERTENCIA

No preste ni alquile nunca su herramienta motorizada sin entregar los manuales de instrucciones de su motor KombiEngine y el accesorio KombiTool.

Asegrese que todas las personas que utilicen la mquina lean y comprendan la informacin contenida en estos manuales.

ADVERTENCIA

El uso de esta mquina puede ser peligroso. Si la herramienta de corte llega a tener contacto con parte alguna de su cuerpo, le causar cortaduras.

Utilice su motor KombiEngine equipado con el cortasetos KombiTool solamente para cortar setos, matorrales, arbustos y materiales similares.

ADVERTENCIA

No debe usarse para ningn otro propsito ya que el uso indebido puede resultar en lesiones personales o daos a la propiedad, incluso daos de la mquina.

ADVERTENCIA

Nunca se debe permitir a los nios que usen esta herramienta motorizada. No se debe permitir la proximidad de otras personas, especialmente de nios, ni de animales en los lugares donde se est utilizando la mquina.

ADVERTENCIA

Para reducir el riesgo de ocasionar lesiones a las personas en la cercana y daos a la propiedad, nunca deje la herramienta motorizada en marcha desatendida. Cuando no est en uso (por ejemplo durante un descanso), apguela y asegrese que las personas no autorizadas no puedan usarla.

Las medidas de seguridad y avisos contenidos en este manual se refieren al uso de todos los cortasetos STIHL. Los distintos modelos pueden contar con piezas y controles diferentes. Vea la seccin correspondiente de sus manuales de instrucciones del motor KombiEngine y accesorio KombiTool para tener una descripcin de los controles y la funcin de los componentes de su modelo.

El uso seguro de una herramienta motorizada atae a

1. el operador

2. la herramienta motorizada

3. el uso de la herramienta motorizada.

EL OPERADOR

Condicin fsica

Usted debe estar en buenas condiciones fsicas y psquicas y no encontrarse bajo la influencia de ninguna sustancia (drogas, alcohol, etc.) que le pueda restar visibilidad, destreza o juicio. No maneje esta mquina cuando est fatigado.

ADVERTENCIA

Est alerta. Si se cansa, tmese un descanso. El cansancio puede provocar una prdida del control. El uso de cualquier herramienta motorizada es fatigoso. Si usted padece de alguna dolencia que pueda ser agravada por la fatiga, consulte a su mdico antes de utilizar esta mquina.

Medidas de seguridad y tcnicas de manejo

Dado que el motor KombiEngine equipado con un accesorio corta- setos KombiTool es una herramienta de corte motorizada, con cuchi- llas afiladas, que funciona a gran veloci- dad, es necesario tomar medidas especiales de seguridad para reducir el riesgo de lesiones personales.

Es importante que usted lea, comprenda bien y respete las siguientes advertencias y medidas de seguridad. Lea peri- dicamente los manuales de instrucciones y las ins- trucciones de seguridad de su motor KombiEngine y acceso- rio KombiTool. El uso descuidado o inadecuado puede causar lesiones graves o incluso la muerte.

HL-KM24

espaol / EE.UU

Vestimenta adecuada

ADVERTENCIA

Para reducir el riesgo de lesiones el operador debe usar el equipo protector adecuado.

ADVERTENCIA Est especialmente alerta y tenga cuidado cuando se usa protectores de odos, ya que los mismos reducen la posibilidad de or seales de advertencia (gritos, alarmas, etc.).

Evite el uso de chaquetas sueltas, bufandas, corbatas, joyas, pantalones acampanados o con botamangas, pelo largo suelto o cualquier cosa que pueda engancharse en las ramas, matorrales o piezas en movimiento de la mquina. Sujtese el pelo de modo que quede sobre los hombros.

Para reducir el riesgo de lesionarse los ojos, nunca maneje la herra- mienta motorizada si no tiene puestas gafas o anteojos de seguridad bien ajustados con una proteccin adecuada en las partes superior y late- ral que satisfagan la norma ANSI Z87 "+" (o la norma nacional corres- pondiente). Para reducir el riesgo de lesionarse la cara, STIHL recomienda usar tambin una careta o protector facial ade- cuado sobre las gafas o anteojos de seguridad.

Utilice un casco de segu- ridad aprobado para reducir el riesgo de lesio- narse la cabeza en caso de existir tal tipo de peligro.

El ruido de la herramienta motorizada puede daar los odos. Siempre use amortiguadores del ruido (tapones u orejeras) para protegerse los odos. Los usuarios constantes y regulares deben some- terse con frecuencia a un examen o control auditivo.

Siempre use guantes gruesos (por ejemplo, fabricados de cuero u otro material resistente al desgaste) cuando mani- pule la mquina y la herramienta de corte. Los guantes gruesos y anti- deslizantes mejoran el manejo y ayudan a prote- ger las manos.

La ropa debe ser de con- feccin fuerte y ajustada, pero no tanto que impida la completa libertad de movimiento. Use pantalo- nes largos hechos de un material grueso para pro- tegerse las piernas. No use pantalones cortos, sandalias o pies descalzos.

HL-KM 25

espaol / EE.UU

Para instrucciones adicionales acerca de la ropa adecuada, vea las precauciones de seguridad, en el manual de instrucciones del motor KombiEngine que est usando.

LA HERRAMIENTA MOTORIZADA (MOTOR KOMBIENGINE PROVISTO CON CORTASETOS KOMBITOOL)

Para las ilustraciones y definiciones de los componentes de la herramienta motorizada, vea el captulo sobre Piezas principales.

ADVERTENCIA

Nunca modifique, de ninguna manera, esta herramienta motorizada. Utilice nicamente los accesorios y repuestos suministrados por STIHL o expresamente autorizados por STIHL para usarse con el motor KombiEngine especfico de STIHL. Si bien es posible conectar a la herramienta motorizada de STIHL ciertos accesorios no autorizados, su uso puede ser, en la prctica, extremadamente peligroso.

Si la mquina experimenta cargas excesivas para las cuales no fue diseada (por ejemplo, impactos severos o una cada), siempre asegrese que est en buenas condiciones antes de seguir con el

trabajo. Compruebe especficamente que los controles y dispositivos de seguridad funcionen correctamente. No siga manejando esta mquina si est daada. En caso de dudas, pida que el concesionario de servicio de STIHL la revise.

EL USO DE LA HERRAMIENTA MOTORIZADA (MOTOR KOMBIENGINE EQUIPADO CON CORTASETOS KOMBITOOL)

Transporte de la herramienta motorizada

ADVERTENCIA

Para reducir el riesgo lesiones debido al contacto con las cuchillas, nunca transporte la herramienta motorizada con las cuchillas en marcha.

ADVERTENCIA

Siempre apague el motor y coloque la funda sobre las cuchillas de corte antes de transportar la herramienta motorizada por una distancia considerable.

Puede acarrearse solamente en posicin horizontal. Agarre el eje de una manera que mantenga la mquina

equilibrada horizontalmente. Mantenga el silenciador caliente lejos de su cuerpo y el accesorio de corte detrs de usted.

ADVERTENCIA

Para reducir el riesgo de lesiones por quemaduras, no toque las piezas de la mquina ni la caja de engranajes cuando estn calientes.

ADVERTENCIA

Cuando transporte la mquina en un vehculo, sujtela firmemente para impedir su vuelco, el derrame de combustible y el dao a la mquina.

En mquinas con barra de corte ajustable: Asegrese que la barra de corte est fijada en su lugar. Vea el captulo "Ajuste del ngulo de la barra de corte" en este manual de instrucciones. En mquinas con posicin de transporte: Mueva la barra de corte a la posicin de transporte y asegrela en esa posicin.

Antes de arrancar

ADVERTENCIA

Siempre revise que la herramienta motorizada est en buenas condiciones y funcione correctamente antes de arrancarla. Nunca intente modificar los controles o los dispositivos de seguridad.

ADVERTENCIA

No maneje nunca una herramienta motorizada que est daada, mal ajustada o mantenida o que no fue armada completa y debidamente.

Es muy importante tener una buena superficie de apoyo para los pies. Pn- gase botas gruesas con suela antideslizante. Recomendamos las botas de seguridad con puntera de acero.

00 2B

A2 54

K N

HL-KM26

espaol / EE.UU

ADVERTENCIA

El accesorio de corte debe estar correctamente apretado y en buenas condiciones de trabajo. Busque piezas sueltas (tuercas, tornillos, etc.) y cuchillas agrietadas, dobladas, deformadas o daadas. Revise peridicamente la condicin de las cuchillas - con el motor apagado! Sustituya las cuchillas daadas antes de usar la herramienta motorizada. Mantenga las cuchillas siempre afiladas.

Mantenga los mangos limpios y secos en todo momento; es particularmente importante mantenerlos libres de humedad, aceite, combustible, grasa o resinas para garantizar que la mquina pueda empuarse firmemente para mantenerla bajo control seguro.

STIHL recomienda que siempre roce las cuchillas con el disolvente de resina STIHL antes de empezar a trabajar con el motor apagado! Este producto protector puede obtenerse a travs del concesionario. Aplique cantidades abundantes.

Ajuste el arns y la empuadura de modo correspondiente a su estatura antes de empezar a trabajar. Para prepararse para emergencias, practique la liberacin rpida de la unidad del arns.

Arranque

En mquinas con barra de corte ajustable: Fije la barra de corte en la posicin de arranque, de la manera descrita en el captulo "Arranque / parada del motor". Si la posicin de arranque no es la posicin de corte

deseada, ser necesario ajustar cuidadosamente la mquina para llegar a la posicin deseada cuando el motor est a marcha en vaco y las cuchillas estn paradas.

En las mquinas con una posicin de transporte especificada (barra de corte plegada contra el tubo de mando): Nunca arranque la mquina en la posicin de transporte. En esta posicin las cuchillas no estn engranadas y, por lo tanto, es imposible verificar visualmente que las mismas se pararn cuando el motor est a marcha en vaco cuando se empieza el ajuste de la barra de corte para llegar a la posicin de corte deseada (con las cuchillas engranadas).

Arranque el motor solamente al aire libre, por lo menos 3 m (10 pies) del lugar en que lo haya llenado.

Para las instrucciones especficas de arranque, vea la seccin correspondiente de los manuales del motor KombiEngine y accesorio KombiTool.

Coloque la herramienta motorizada sobre suelo firme u otra superficie slida en un lugar abierto. Mantenga el equilibrio y elija un buen punto de apoyo para los pies.

ADVERTENCIA

Para reducir el riesgo de sufrir lesiones causadas por la prdida de control, no intente arrancar el motor de la herramienta "por lanzamiento".

ADVERTENCIA

Para reducir el riesgo de lesiones debido al contacto con las cuchillas, est absolutamente seguro que la herramienta de corte se encuentra lejos de su cuerpo y de todas las obstrucciones y objetos, incluido el suelo, porque al arrancar el motor acelerado, su velocidad ser lo suficientemente rpida para que el embrague se engrane y mueva la herramienta de corte.

Tan pronto arranque, accione inmediatamente por un breve momento el gatillo de aceleracin para desconectarlo de la posicin de arranque y permitir que el motor se desacelere a la marcha en vaco.

Con el motor funcionando a marcha en vaco solamente, enganche la herramienta motorizada al gancho de resorte de su arns (vea el captulo correspondiente en este manual).

ADVERTENCIA

Su herramienta motorizada es una mquina que debe ser manejada por solamente una persona. No deje que otras personas estn en el lugar de trabajo, aun durante el arranque.

Vea tambin las precauciones de seguridad de arranque en el manual de instrucciones del motor KombiEngine.

HL-KM 27

espaol / EE.UU

Durante el funcionamiento

Sujecin y control de la herramienta motorizada

Al trabajar, siempre sujete la mquina firmemente con ambas manos en los mangos. Cierre firmemente los dedos y pulgares sobre los mangos.

Modelos con mango trico

Coloque su mano derecha en el mango de control, la izquierda en el mango trico del tubo de mando, aun si usted es zurdo. Cierre firmemente los dedos y pulgares sobre los mangos.

Mquinas con manguera de mango

Coloque su mano derecha en el mango de control, la izquierda en la manguera del tubo de mando, aun si usted es zurdo. Cierre firmemente los dedos y pulgares sobre los mangos.

ADVERTENCIA

ADVERTENCIA

No trate de llegar ms lejos de lo debido. Mantenga los pies bien apoyados y equilibrados en todo momento. Se debe tener cuidado especial cuando las condiciones del suelo son resbaladizas (suelo hmedo, nieve) y en terreno difcil y con mucha vegetacin. Para evitar tropezarse, est atento a los obstculos ocultos tales como tocones, races y zanjas. Para obtener un punto de apoyo seguro, quite las ramas cadas, los matorrales y el material cortado. Sea sumamente precavido cuando trabaje en declives o terreno irregular.

ADVERTENCIA

Para reducir el riesgo de lesiones causadas por la prdida del control, nunca trabaje sobre una escalera, un rbol o cualquier otra superficie de

soporte poco seguro. Nunca mantenga la mquina a una altura ms arriba de los hombros.

Condiciones de trabajo

Arranque y use la herramienta motorizada nicamente a la intemperie, en una zona bien ventilada. Manjela solamente en condiciones de buena visibilidad y a la luz del da. Trabaje con mucho cuidado.

ADVERTENCIA

Si la vegetacin que se est cortando o la tierra en el lugar est recubierta de una sustancia qumica (tal como un pesticida o herbicida activo), lea y siga las instrucciones suministradas con la sustancia en cuestin.

ADVERTENCIA

La inhalacin repetida o de grandes cantidades de polvo u otros contaminantes del aire, especialmente los de partculas pequeas puede causar enfermedades respiratorias o de otro tipo. Controle el polvo en su fuente, siempre que sea posible. Utilice buenas prcticas de trabajo, tal como trabajar de manera que el viento o el proceso de corte dirija el polvo producido por la herramienta motorizada en sentido opuesto del operador. Observe las

00 00 -G X X -1 67 7- A 0

00 00 -G X X -1 67 8- A 0

Nunca intente manejar la herramienta motorizada con una sola mano. La prdida de control de la herramienta motorizada puede ocasionar lesiones graves o mortales. Para reducir el riesgo de lesio- narse, mantenga las manos y los pies alejados de la herramienta de corte. No toque nunca con las manos ni con cualquier parte del cuerpo una herramienta de corte en movimiento.

La inhalacin de ciertos polvos, especialmente los polvos orgnicos, tales como el moho o polen, puede provocar reacciones alrgicas o asmticas en las perso- nas sensibles.

HL-KM28

espaol / EE.UU

recomendaciones emitidas por EPA/OSHA/NIOSH y las asociaciones de trabajo y los sindicatos con respecto al polvo ("materia particulada"). Si no es posible controlar la inhalacin de polvo de manera significativa, es decir, mantenerla al nivel de ambiente (fondo) o cerca del mismo, el operador y los dems debern usar una mascarilla de respiracin aprobada por NIOSH / MSHA para el tipo de polvo existente.

Instrucciones de manejo

ADVERTENCIA

No maneje la herramienta motorizada usando el bloqueo de acelerador para arranque, pues no tendr control de la velocidad del motor.

En caso de emergencia, apague el motor inmediatamente mueva el control deslizante / interruptor momentneo de parada a 0 o STOP

Consulte la seccin del manual de instrucciones del motor KombiEngine que describe el uso del control deslizante / interruptor de parada / interruptor momentneo de parada.

ADVERTENCIA

Las cuchillas siguen girando por un rato despus que se suelta el gatillo de aceleracin.

Al aumentar la velocidad del motor con las cuchillas bloqueadas se aumenta la carga y se provoca el patinaje continuo del embrague. Esto puede causar sobrecalentamiento y dao de los componentes importantes (por ejemplo, el embrague y las piezas de plstico polimrico de la caja) esto a su vez

aumenta el riesgo de lesiones causadas por el movimiento de las cuchillas cuando el motor est a marcha en vaco.

ADVERTENCIA

En mquinas con barra de corte ajustable: Ajuste la barra de corte cuidadosamente para colocarla en la posicin de corte deseada. Para evitar el riesgo de lesionarse, nunca toque las cuchillas al hacer ajustes. Ajuste la barra de corte solamente cuando las cuchillas estn paradas.

La herramienta motorizada tiene alcance largo. Para reducir el riesgo de que otras personas sufran lesiones graves o mortales causadas por la cada de objetos, o el contacto inesperado con las cuchillas en movimiento de la herramienta motorizada, siempre mantenga a las dems personas a una distancia no menor de 5 m (17 pies) de la herramienta motorizada cuando se encuentre en marcha.

PELIGRO

La electricidad puede saltar de un punto a otro al formar arcos en el aire. Los niveles altos de voltaje aumentan la distancia sobre la cual la electricidad puede formar arcos. La electricidad tambin puede conducirse por las ramas de un rbol, especialmente si stas estn hmedas. Guarde una distancia no menor de 15 m (50 pies) entre el podador de varilla (incluyendo las ramas con las cuales tenga contacto) y todas las lneas que conduzcan corriente elctrica. Antes de trabajar a una distancia menor, comunquese con la empresa de servicio elctrico y comprobar que se haya interrumpido el suministro elctrico.

Apague el motor inmediatamente si se le aproxima alguna persona.

ADVERTENCIA

Antes de empezar a trabajar, examine la zona alrededor del seto en busca de piedras, vidrio, alambres, piezas metlicas, basura u otros objetos macizos que pudieran daar las cuchillas.

17ft (5m)

50ft (15m )

Su herramienta motori- zada no est aislada contra las sacudidas elctricas. Para reducir el riesgo de electrocucin, nunca utilice esta herra- mienta motorizada cerca de alambres o cables (de alimentacin, etc.) que puedan tener corriente elctrica.

HL-KM 29

espaol / EE.UU

Tenga cuidado especial al cortar setos cerca de vallas de alambre. No toque el alambre con las cuchillas. Cuando se trabaje cerca del suelo, compruebe que no entre arena, grava o piedras entre las cuchillas de corte.

El choque con objetos extraos tales como piedras, alambres o piezas metlicas puede daar el accesorio de corte y puede hacer que las cuchillas se agrieten, se piquen o se rompan. STIHL no recomienda usar la herramienta motorizada en zonas en las cuales las cuchillas pudieran entrar en contacto con tales objetos.

ADVERTENCIA

Observe las cuchillas en todo momento no corte las zonas del seto que no pueda ver. Cuando pode la parte superior de un seto ms alto, inspeccione frecuentemente el otro lado del seto para cerciorarse que no haya personas, animales ni obstrucciones.

ADVERTENCIA

Si la herramienta de corte se atasca o queda pegada, siempre apague el motor y asegrese que la herramienta de corte est detenida antes de limpiarla. Limpie el pasto, las malezas, etc. de la herramienta de corte en intervalos regulares.

Revise las cuchillas frecuente y peridicamente durante el trabajo, o inmediatamente si hay cambios importantes de las caractersticas de corte:

Apague el motor.

Espere hasta que se detengan completamente las cuchillas.

Revise la condicin y el apriete, busque grietas.

Revise el afilado.

Sustituya las herramientas de corte daadas o desafiladas inmediatamente, incluso si tienen slo alguna grieta superficial.

ADVERTENCIA

MANTENIMIENTO, REPARACIN Y ALMACENAMIENTO

ADVERTENCIA

Siempre apague el motor y verifique que el accesorio de corte est parado antes de llevar a cabo cualquier trabajo de mantenimiento, reparacin o limpieza de la herramienta motorizada. No intente hacer ningn trabajo de mantenimiento o reparacin que no est descrito en su manual de instrucciones del motor KombiEngine o del accesorio KombiTool. Este tipo de trabajo debe realizarse nicamente en el taller de servicio de STIHL.

Siempre limpie el polvo y la tierra de la mquina no utilice disolventes de grasa para este propsito.

Roce las cuchillas con disolvente de resina STIHL. Despus ponga en marcha el motor para que el disolvente se distribuya uniformemente.

ADVERTENCIA

Utilice solamente las piezas de repuesto idnticas de STIHL para el mantenimiento y la reparacin. El uso de piezas no fabricadas por STIHL puede causar lesiones graves o mortales.

Use guantes para manipular o reparar las cuchillas.

ADVERTENCIA

Nunca repare los accesorios de corte daados aplicndoles soldadura, enderezndolos o modificndoles su forma. Esto puede causar el desprendimiento de alguna pieza del accesorio de corte y producir lesiones graves o mortales.

Mantenga las cuchillas afiladas. Apriete todas las tuercas, pernos y tornillos, excepto los tornillos de ajuste del carburador, despus de cada uso.

No limpie la mquina con una lavadora a presin. El chorro fuerte de agua puede daar las piezas de la mquina.

Guarde la herramienta motorizada en un lugar seco y elevado o con llave lejos del alcance de los nios.

La caja de engranajes est caliente durante el funcionamiento de la mquina. Para reducir el riesgo de lesiones por quemaduras, no toque la caja de engranajes cuando est caliente.

HL-KM30

espaol / EE.UU

Temporada de corte

Respete las leyes y los reglamentos nacionales o municipales en cuanto al corte de setos.

No utilice el cortasetos durante los perodos acostumbrados de descanso en el vecindario.

Secuencia de corte

Si es necesario hacer un corte radical, corte poco a poco haciendo varias pasadas.

Utilice tijeras para cortar las ramas gruesas primero.

Corte los lados del seto primero, y despus la parte superior.

Desecho

No tire los recortes al basurero pueden usarse para abono.

Preparaciones

N Caja de engranajes ajustable: Ajuste la barra de corte al ngulo deseado.

N Saque la funda de la cuchilla.

N Arranque el motor.

N Si utiliza un arns: Pngase el arns y engnchelo a la mquina.

Tcnicas de trabajo

Corte horizontal (con barra de corte orientada angularmente)

Corte cerca del suelo, estando de pie, por ejemplo, matorrales de poca altura.

Gire la barra de corte hacia arriba y abajo al cortar el seto utilice ambos lados de las cuchillas de corte, no apoye la barra de corte sobre el suelo.

Corte vertical (con barra de corte orientada angularmente)

Corte sin pararse directamente junto al seto, por ejemplo, si hay flores entre el operador y el seto.

Gire la barra de corte hacia arriba y hacia abajo describiendo un arco al cortar el seto utilice ambos lados de la cuchilla de corte.

Uso

38 8B

A0 29

K N

38 8B

A0 30

K N

HL-KM 31

espaol / EE.UU

Corte vertical (con barra de corte recta)

Alcance mximo sin la necesidad de otros accesorios

Gire la barra de corte hacia arriba y hacia abajo describiendo un arco al cortar el seto utilice ambos lados de la cuchilla de corte.

Corte elevado (con barra de corte orientada angularmente)

Sostenga el cortasetos en posicin vertical y muvalo describiendo un arco para obtener el aprovechamiento mximo de su alcance.

ADVERTENCIA

Toda posicin de trabajo elevada sobre el nivel de la cabeza produce cansancio. Para reducir el riesgo de accidentes, trabaje en estas posiciones slo por perodos breves. Ajuste el ngulo de la barra de corte ajustable al mximo, de modo que se pueda sostener la mquina en una posicin ms baja para producir menos cansancio (con la correa para el hombro), pero que provea un alcance adecuado.

Corte horizontal (con barra de corte recta)

Sujete la barra de corte a un ngulo de 0 a 10 al desplazar el cortasetos en sentido horizontal.

38 9B

A 05

0 K

N

38 8B

A0 31

K N

38 8B

A0 32

K N

HL-KM32

espaol / EE.UU

Desplace la barra de corte describiendo un arco hacia el exterior del seto, de modo que los trozos cortados caigan al suelo.

Recomendacin: Solamente corte los setos que no son ms altas que la altura del pecho.

Motores KombiEngine

Utilice nicamente los motores KombiMotor suministrados o explcitamente aprobados por STIHL para uso con el accesorio.

Este accesorio KombiTool puede usarse nicamente con los motores KombiMotor siguientes:

STIHL KM 56 R, KM 85 R, KM 91 R, KM 94 R, KM 111 R, KM 131 R, KMA 130 R, KMA 135 R

N Empuje la orejeta (1) del tubo de mando en la ranura (2) en el manguito de acoplamiento hasta que haga tope.

Cuando la instalacin es correcta, la raya roja (3) (punta de la flecha) debe estar a ras con el extremo del manguito de acoplamiento.

N Apriete la perilla (4) firmemente.

Retiro del accesorio KombiTool

N Invierta la secuencia anterior para retirar el tubo de mando.

38 8B

A0 33

K N

Motores KombiEngine aprobados

Instalacin del KombiTool

1

00 2B

A3 26

K N

2

3

00 2B

A3 27

K N

4

HL-KM 33

espaol / EE.UU

Retiro de la tapa protectora

Si tiene montado una tapa en el extremo del tubo de mando de la KombiTool o de la herramienta motorizada de base:

N Quite la tapa protectora del extremo del tubo de mando y djela en un lugar seguro.

Si el tapn se sale del tubo de mando cuando se quita la tapa:

N Empuje el tapn en el tubo de mando hasta llegar al tope.

Montaje de la caja de engranajes

N Suelte los tornillos de fijacin (10).

N Empuje la caja de engranajes (11) en el tubo de mando (5) y gire la caja de engranajes (11) hacia adelante y atrs segn sea necesario.

Cuando el extremo del tubo de mando pase ms all de la ranura en la abrazadera (12):

N Empuje el tubo de mando (11) en su posicin hasta llegar al tope.

N Apriete los tornillos de fijacin de la abrazadera moderadamente.

N Alinee la caja de engranajes (11) con el motor.

N Apriete los tornillos de fijacin firmemente.

Armado de la mquina

41 3B

A 01

4 K

N 00

2B A2

48 K

N

11 1010

5

00 00 -G X X -1 68 1- A 0

11

12

00 00 -G X X -1 68 2- A 0

HL-KM34

espaol / EE.UU

Ajustador de ngulo - 145

El ngulo de la barra de corte puede ajustarse hacia arriba en 4 posiciones entre 0 (recta) y 55, y hacia abajo en 7 posiciones entre 0 y 90 (hacia abajo en ngulo recto). Por lo tanto, se puede elegir entre 12 posiciones de trabajo posibles.

ADVERTENCIA

Para reducir el riesgo de lesiones, realice el ajuste siempre con las cuchillas paradas y el motor en marcha en vaco.

ADVERTENCIA

La caja de engranajes se calienta durante el funcionamiento de la mquina. Para reducir el riesgo de sufrir quemaduras, no toque la caja de engranajes.

ADVERTENCIA

Para reducir el riesgo de lesionarse, nunca toque las cuchillas cuando haga ajustes.

N Tire hacia atrs del manguito deslizante (1) y use la palanca (2) para ajustar la unin uno o varios orificios.

N Suelte el manguito deslizante (1) y asegrese de que el pasador se engancha en el cuadrante (3).

Posicin de transporte

La barra de corte puede plegarse contra el tubo de mando y fijarse en esta posicin para reducir el espacio necesario para transportar el equipo.

ADVERTENCIA

Para reducir el riesgo de sufrir lesiones, apague siempre el motor (apriete el interruptor de parada), y cubra las cuchillas con su funda antes de colocar la barra de corte en la posicin de transporte, o de bajarla de nuevo a la posicin de trabajo normal.

ADVERTENCIA

La caja de engranajes se calienta durante el funcionamiento de la mquina. Para reducir el riesgo de sufrir quemaduras, no toque la caja de engranajes.

Ajuste de la barra de corte

00 00 -G X X -1 68 3- A 0

145

00 00 -G X X -1 68 4- A 0

3

2

1

00 00 -G X X -1 68 5- A 0

HL-KM 35

espaol / EE.UU

N Apague el motor.

N Cubra las cuchillas con su funda.

N Tire hacia atrs del manguito deslizante (1) y use la palanca (2) para girar la unin hacia arriba, en direccin al tubo de mando, hasta que la barra de corte quede al ras contra el tubo de mando.

N Suelte el manguito deslizante (1) y asegrese de que el pasador se engancha en el cuadrante (3).

El tipo y el estilo del arns y mosquetn (gancho con resorte) dependen del lugar de venta.

Correa para hombro

N Colquese la correa (1) sobre el hombro.

N Ajuste el largo de la correa de modo que el mosquetn (2) quede aproximadamente el ancho de la mano por debajo de su cadera derecha.

Arns completo

N Pngase el arns completo (1).

N Ajuste el largo de la correa de modo que el mosquetn (2) quede aproximadamente el ancho de la mano por debajo de su cadera derecha.

N Cierre la placa de bloqueo (3).

00 00 -G X X -1 68 6- A 0

1

2

3 Uso de la correa para hombro

1

00 2B

A3 74

K N

2

1

00 2B

A3 07

K N

2

3

HL-KM36

espaol / EE.UU

Conexin de la mquina al arns

N Enganche el mosquetn (1) en la argolla para transporte (2) ubicada en el tubo de mando mantenga fija la argolla para transporte.

Desconexin de la mquina del arns

N Empuje la barra en el mosquetn (1) y extraiga la argolla de transporte (2) del mosquetn.

Eliminacin de la mquina

ADVERTENCIA

Es necesario quitarse la mquina rpidamente en caso de un peligro inminente. Practique quitarse la mquina y colocarla en el suelo de la manera en la cual lo hara en caso de

emergencia. Para evitar daar la mquina, no la lance al suelo cuando est practicando.

Practique la desconexin de la herramienta motorizada del mosquetn de la manera descrita en "Desconexin de la mquina del arns".

Si utiliza una correa para el hombro: Practique el deslizamiento de la correa fuera de su hombro.

Si utiliza un arns completo: Practique el desbloqueo rpido de la placa de bloqueo y el deslizamiento de las correas del arns de sus hombros.

Arranque del motor

Siga siempre las instrucciones de funcionamiento del motor KombiEngine y la herramienta motorizada bsica.

N Coloque la mquina sobre el suelo de modo que quede apoyada seguramente en el soporte del motor y en la caja de engranajes.

N En los modelos con barra de corte ajustable: Fija la barra de corte en la posicin recta (0).

N Saque la funda de la cuchilla.

Para reducir el riesgo de sufrir accidentes, verifique que las cuchillas no toquen el suelo ni ningn otro obstculo.

1

00 2B

A3 08

K N2

1 2

1

00 2B

A3 10

K N2

1 2

Arranque / parada del motor

00 2B

A 03

8 K

N 00

2B A

07 2

K N

HL-KM 37

espaol / EE.UU

N De ser necesario, apoye la caja de engranajes sobre un soporte elevado (por ejemplo, un montculo, ladrillo u objeto similar).

N Asegrese de tener los pies bien apoyados ya sea de estar a pie, agacharse o arrodillarse.

N Sujete la mquina con la mano izquierda y presionarla contra el suelo firmemente no toque los mandos del mango de control al presionarla consulte el manual de instrucciones del motor KombiEngine o de la herramienta motorizada bsica.

INDICACIN No se pare ni se arrodille sobre el tubo de mando.

ADVERTENCIA

El accesorio de corte puede empezar a girar tan pronto arranque el motor. Por esta razn, accione momentneamente el gatillo de aceleracin el motor reduce su aceleracin al rgimen de marcha en vaco.

El procedimiento de arranque siguiente corresponde al descrito en el manual de instrucciones del motor KombiEngine o la herramienta motorizada bsica que se est usando.

Parada del motor

N Consulte el manual de instrucciones del motor KombiEngine o de la herramienta motorizada bsica.

Engranaje impulsor de cuchillas

Lubrique el engranaje impulsor de cuchillas con lubricante para engranajes STIHL para cortasetos vea "Accesorios especiales".

Versin HL 0

Versin ajustable HL 145

N Revise el nivel de lubricante despus de aproximadamente cada 25 horas de funcionamiento. Destornille el tapn de llenado (1)

Si no se ve grasa en el interior del tapn, atornille el tubo de grasa en el agujero de llenado.

N Inyecte hasta 10 g (2/5 oz) de grasa en la caja de engranajes.

INDICACIN No llene completamente con grasa la caja de engranajes.

N Destornille el tubo de grasa del agujero de llenado.

N Vuelva a colocar el tapn de llenado y apritelo firmemente.

Transmisin angular

Lubrique la transmisin angular con lubricante para engranajes STIHL para cortasetos (accesorio especial).

Versin ajustable HL 145

N Revise el nivel de lubricante despus de aproximadamente cada 25 horas de funcionamiento. Destornille el tapn de llenado (2) Si no se ve grasa en el interior del tapn, atornille el tubo de grasa en el agujero de llenado.

N Inyecte hasta 5 g (1/5 oz) de grasa en la caja de engranajes.

Lubricacin de la caja de engranajes

1

00 00 -G X X -1 68 7- A 0

1 00 00 -G X X -1 68 8- A 0

00 00 -G X X -1 68 9- A 0

2

HL-KM38

espaol / EE.UU

INDICACIN No llene completamente con grasa la caja de engranajes.

N Destornille el tubo de grasa del agujero de llenado.

N Vuelva a colocar el tapn de llenado y apritelo firmemente.

Para intervalos de 3 meses o ms

N Limpie las cuchillas, revise su estado y rocelas con disolvente de resina STIHL.

N Coloque la funda de la cuchilla.

N Si el accesorio KombiTool se retira del motor KombiEngine y se guarda aparte: Coloque la tapa protectora en el tubo de mando para protegerla del polvo y la suciedad.

N Guarde la mquina en un lugar seco y bajo llave, fuera del alcance de los nios y de otras personas no autorizadas.

Los intervalos dados a continuacin corresponden nicamente a condiciones normales de trabajo. Si el tiempo de trabajo por jornada es ms largo que lo normal, o si las condiciones son extremas (zonas polvorientas, etc.), acorte los intervalos indicados de modo correspondiente.

Todos los tornillos y tuercas accesibles

N Revselos y apritelos de ser necesario (no los tornillos ni las tuercas de las cuchillas de corte)

Cuchillas de corte

N Inspeccin visual antes de iniciar los trabajos

N Afile de ser necesario

N Sustituya si est daado.

Lubricacin de caja de engranajes

N Revise antes de iniciar los trabajos

N Vuelva a llenar segn sea necesario.

Etiquetas de seguridad

N Cambie las etiquetas de seguridad ilegibles

Almacenamiento de la mquina

Informacin para mantenimiento

HL-KM 39

espaol / EE.UU

Si el rendimiento del corte y la respuesta de la mquina comienzan a deteriorar (por ejemplo, si las cuchillas se enganchan frecuentemente en las ramas): Vuelva a afilar las cuchillas.

Es mejor que las cuchillas las afile el concesionario usando un afilador de taller. STIHL recomienda acudir a un concesionario STIHL para servicio.

INDICACIN No utilice la mquina con cuchillas romas o daadas. Esto puede causar sobrecargas y produce cortes insatisfactorios.

Instrucciones de afilado

HL-KM40

espaol / EE.UU

1 Cuchillas de corte 2 Engranaje impulsor de cuchillas 3 Tubo de mando 4 Transmisin angular 5 Manguito deslizante 6 Cuadrante 7 Palanca de ajuste 8 Funda para cuchilla 9 Manguito

Componentes importantes

2 8

4

1

5

7

4 3

2

47 5B

A0 08

K N

6

3

HL-KM 41

espaol / EE.UU

Definiciones

1 Cuchillas de corte Cuchillas de acero para cortar setos y arbustos.

2 Engranaje impulsor de cuchillas Convierte el movimiento giratorio de la transmisin angular en movimiento de vaivn de las cuchillas.

3 Tubo de mando Encierra y protege el eje impulsor entre el manguito de acoplamiento y la caja de engranajes.

4 Transmisin angular Transmite el movimiento giratorio del eje impulsor al engranaje impulsor de cuchillas.

5 Manguito deslizante Bloquea y desbloquea el mecanismo de ajuste de la barra de corte.

6 Cuadrante Fija la barra de corte en la posicin requerida.

7 Palanca de ajuste Se usa para fijar la barra de corte al ngulo deseado.

8 Funda para cuchilla Cubre las cuchillas cuando el cortasetos no est en uso.

9 Manguito Sita el tubo de mando en el manguito de acoplamiento.

Cuchillas de corte

Peso

Los usuarios de esta mquina deben efectuar nicamente los trabajos de mantenimiento descritos en este manual. STIHL recomienda que un concesionario de servicio STIHL efecte los dems trabajos de reparacin utilizando piezas de repuesto genuinas de STIHL.

Es posible identificar las piezas originales de STIHL por el nmero de pieza STIHL, el logotipo de { y, en ciertos casos, el smbolo K de piezas STIHL. En las piezas pequeas el smbolo puede aparecer solo.

Para reparar algn componente del sistema de control de emisiones de aire, consulte la garanta de sistemas de emisiones dada en este manual.

Especificaciones

Tipo de cuchilla: De doble filo Largo de cuchilla: 500 mm

(19,685 in), 600 mm (23,622 in)

Espacio entre dientes: 34 mm (1,339 pulg)

Altura de dientes: 22 mm (0,866 pulg)

ngulo de afilado: 45 con res- pecto al nivel de la cuchilla

HL-KM 0 500 mm: 1,7 kg (3,7 lb) HL-KM 0 600 mm: 1,8 kg (4,0 lb) HL-KM 145 500 mm: 2,4 kg (5,3 lb) HL-KM 145 600 mm: 2,6 kg (5,7 lb)

Informacin de reparacin

HL-KM42

espaol / EE.UU

Respete todas las leyes y los reglamentos sobre eliminacin de desechos que correspondan a su pas.

No se debe botar los aparatos STIHL en el basurero. Lleve el producto, los accesorios y el embalaje a un vertedero autorizado para reciclarlos y contribuir al cuidado del medio ambiente.

Comunquese con un concesionario de servicio de STIHL para obtener la informacin ms actualizada sobre la eliminacin de desechos.

Marcas registradas de STIHL

STIHL

{

K

La combinacin de colores anaranjado- gris (Nmeros de registro EE.UU. 2,821,860; 3,010,057, 3,010,058, 3,400,477; y 3,400,476)

AutoCut

FARM BOSS

iCademy

MAGNUM

MasterWrench Service

MotoMix

OILOMATIC

ROCK BOSS

STIHL Cutquik

STIHL DUROMATIC

STIHL Quickstop

STIHL ROLLOMATIC

STIHL WOOD BOSS

TIMBERSPORTS

WOOD BOSS

YARD BOSS

Algunos de las marcas comerciales de STIHL por ley comn

4-MIX

BioPlus

Easy2Start

EasySpool

ElastoStart

Ematic

FixCut

IntelliCarb

Master Control Lever

Micro

Pro Mark

Quiet Line

STIHL M-Tronic

Desecho

00 0B

A0 73

K N

Marcas comerciales

TM

STIHL Injection

HL-KM 43

espaol / EE.UU

STIHL OUTFITTERS

STIHL PICCO

STIHL PolyCut

STIHL PowerSweep

STIHL Precision Series

STIHL RAPID

STIHL SuperCut

TapAction

TrimCut

Esta lista de marcas comerciales est sujeta a cambios.

Queda terminantemente prohibido todo uso de estas marcas comerciales sin el consentimiento expreso por escrito de ANDREAS STIHL AG & Co. KG, Waiblingen.

HL-KM44

www.stihl.com

0458-475-8621-E

englisch / spanisch USA U

lisc / s isc

WARNING

This product contains chemicals known to the State of California to cause

cancer, birth defects or other reproductive harm.

ADVERTENCIA

Este producto contiene sustancias qumicas consideradas por el Estado de California como causantes de cncer, defectos de nacimiento u

otra

Manualsnet FAQs

If you want to find out how the HL-KM Stihl works, you can view and download the Stihl HL-KM v2 Instruction Manual on the Manualsnet website.

Yes, we have the Instruction Manual for Stihl HL-KM as well as other Stihl manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Instruction Manual should include all the details that are needed to use a Stihl HL-KM. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Stihl HL-KM v2 Instruction Manual is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Stihl HL-KM v2 Instruction Manual consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Stihl HL-KM v2 Instruction Manual free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Stihl HL-KM v2 Instruction Manual, simply download the document to your computer. Once downloaded, open the PDF file and print the Stihl HL-KM v2 Instruction Manual as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.