Sony CAV-CVS12ES Installation Manual PDF

1 of 16
1 of 16

Summary of Content for Sony CAV-CVS12ES Installation Manual PDF

SONY CAV-CVS12ES (US) 3-198-136-11(1)

3-198-136-11(1)

Component Video Switcher

2007 Sony Corporation

CAV-CVS12ES

Installation Manual

Owners Record The model and serial numbers are located on the rear panel. Record the model and serial numbers in the spaces provided below. Refer to them whenever you call upon your Sony dealer regarding this product.

Model No. Serial No.

2US

SONY CAV-CVS12ES (US) 3-198-136-11(1)

WARNING

To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.

To reduce the risk of fire or electric shock, do not place objects filled with liquids, such as vases, on the apparatus.

This symbol is intended to alert the user to the presence of uninsulated dangerous voltage within the products enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

WARNING This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the

equipment and receiver. Connect the equipment into an outlet on a

circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/ TV technician for help.

CAUTION You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment.

Important Safety Instruction 1 Read these instructions. 2 Keep these instructions. 3 Heed all warnings. 4 Follow all instructions. 5 Do not use this apparatus near water. 6 Clean only with dry cloth. 7 Do not block any ventilation openings.

Install in accordance with the manufacturers instructions.

8 Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

9 Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10 Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11 Only use attachments/accessories specified by the manufacturer.

12 Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/ apparatus combination to avoid injury from tip-over.

13 Unplug this apparatus during lightning storms or when unused for long periods of time.

14 Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

Welcome! Thank you for purchasing the Component Video Switcher. Before operating the unit, please read this manual thoroughly and retain it for future reference.

SONY CAV-CVS12ES (US) 3-198-136-11(1)

3US

Table of ConTenTs Chapter 1 Getting Started Features 4 Unpacking 5 Parts and Controls 6

Chapter 2 Setting up the Component Video Switcher Installing the Component Video Switcher 8 Hooking up the Component Video Switcher 10

Chapter 3 Other Information Precautions 12 Troubleshooting 13 Specifications 14

US

SONY CAV-CVS12ES (US) 3-198-136-11(1)

Chapter 1 Getting Started This chapter provides information on the features, parts, and controls of the Component Video Switcher.

Features

You can control up to twelve video sources in up to twelve zones (e.g., rooms or areas) with this CAV-CVS12ES Component Video Switcher. The Component Video Switcher allows you to: Distribute HD video signals in up to twelve zones. Up-convert up to four composite video signals to component

video signals for higher quality. Control the source component in synchronization with the

CAV-M1000ES via RS-232C commands. Control the source component via IR control signal. Transmit video signals throughout the house using a CAT5

(Category 5e) cable.

SONY CAV-CVS12ES (US) 3-198-136-11(1)

US

G etting Started

Unpacking

The CAV-CVS12ES Component Video Switcher includes the following: CAV-CVS12ES Component Video Switcher AC power cord Installation Manual (this manual) Rack-mount brackets (2)

G etting Started

6US

SONY CAV-CVS12ES (US) 3-198-136-11(1)

ZONE

1 2 3 4 5 6 7 8 9 10 11 12

1 2 3 4 5 6 7 8 9 10 11 12

POWER

SOURCE

POWER switch Press to turn the power on or off.

ZONE indicator The selected zone number lights up.

ZONE selector Turn to select the zone. Each time you turn the ZONE selector, the zone changes cyclically as shown below.

1 2 3 10 11 12

SOURCE indicator The source number selected for the zone lights up. When the zone does not select any source component, no SOURCE indicator lights up.

Note When you assign two or more source components to the same source number, the assigned source numbers of the SOURCE indicator blink as an error indication.

Front panel of the Component Video Switcher

Parts and Controls

SOURCE selector Turn to select the source component. Each time you turn the SOURCE selector, the source component changes cyclically as shown below.

1 2 3 10 11 12 OFF

When the OFF is selected, no SOURCE indicator lights up.

SONY CAV-CVS12ES (US) 3-198-136-11(1)

7US

G etting Started

Rear panel of the Component Video Switcher

~ AC IN

SOURCE 12

OUTIN

S12

ASSIGNABLE

SOURCE 11

OUTIN

S11

ASSIGNABLE

SOURCE 10

OUTIN

S10

ASSIGNABLE

SOURCE 9

OUTIN

S9

ASSIGNABLE

SOURCE 8 OUTIN

SOURCE 7 OUTIN

SOURCE 6 OUTIN

SOURCE 5 OUTIN

SOURCE 2 OUTIN

SOURCE 1 OUTIN

Y

PB

PR

SOURCE 4 OUTIN

SOURCE 3 OUTIN

ZONE 3 VIDEO OUT

ZONE 2 VIDEO OUT

ZONE 1 VIDEO OUT

ZONE 4 VIDEO OUT

ZONE 5 VIDEO OUT

ZONE 6 VIDEO OUT

ZONE 7 VIDEO OUT

ZONE 8 VIDEO OUT

ZONE 9 VIDEO OUT

ZONE 10 VIDEO OUT

ZONE 11 VIDEO OUT

ZONE 12 VIDEO OUT

IR REMOTE

IN

RS-232C

CAVAUX

SOURCE 1 ~ 8 connection jacks

a) VIDEO IN An RCA jack for component video input from a source component.

b) VIDEO OUT An RCA jack for connecting a video source to another local component.

Note The video loop-through output is not active when the Main Unit is turned off.

SOURCE 9 ~ 12 connection jacks

a) VIDEO IN An RCA jack for composite video input from a source component.

b) VIDEO OUT An RCA jack for connecting a video source to another local component. The composite video signal is up-converted to the component video signal automatically.

Note The video loop-through output is not active when the Main Unit is turned off.

ASSIGNABLE switch for SOURCE 9 ~ 12 Assign the source component connected to source 9 ~ 12 to source 1 ~ 8. For example, when the SOURCE 9 ASSIGNABLE switch is set to 1, the source 9 video signal is distributed to the zone selected for source 1.

Notes Set the ASSIGNABLE switch to 0 when you do not use the

assign function. When you assign two or more source components to the same

source number, the assigned source numbers of SOURCE indicator blink as an error indication.

AC IN Connects the supplied AC power cord to AC IN.

ZONE VIDEO OUT A CAT5 RJ45 connector that sends a source video signal to the component video input of a zone. Use a CAT5 cable for the connection.

IR REMOTE IN A 3.5 mm monaural mini jack for receiving the SIRCS code from the connected IR-controlled component. The Main Unit can be equally controlled by the RS-232C commands.

Note The remote control is not supplied.

RS-232C

a) AUX Connects to other RS-232C components, allowing the Main Unit to be controlled by other RS-232C components. Use an RS-232C cross cable for the connection.

b) CAV Connects to the CAV-M1000ES, allowing the Main Unit to be controlled by the CAV-M1000ES. Use an RS-232C cross cable for the connection.

8US

SONY CAV-CVS12ES (US) 3-198-136-11(1)

Chapter 2 Setting up the Component Video Switcher This chapter provides information on the Component Video Switcher regarding installation, hookups and settings.

Installing the Component Video Switcher When installing the Component Video Switcher, note the following: Place the Component Video Switcher on a flat and level

surface. When installing the Component Video Switcher in a cabinet,

make sure the back of the cabinet is open to allow adequate ventilation, prevent heat buildup, and prolong the life of the unit.

Place a board under the Component Video Switcher if it is located on a carpet to allow adequate ventilation on the bottom.

Make sure the weight is equally distributed on each of its four feet.

Do not place anything on the top of the Component Video Switcher that might block the ventilation holes and cause malfunction.

Do not place anything on the front or rear panel that might damage the Component Video Switchers control buttons and connectors.

Use caution when placing the unit on surfaces that have been specially treated (with wax, oil, polish, etc.) as staining or discoloration of the surface may result.

SONY CAV-CVS12ES (US) 3-198-136-11(1)

9US

Setting up the Com ponent V

ideo Sw itcher

Using rack-mount brackets

You can also mount the Component Video Switcher into a rack. Make sure that you measure the space needed before mounting.

1 DetachthefourfeetoftheComponentVideoSwitcher.

2 DetachthesixscrewsattachedtotheComponentVideo Switcherasshownbelow.

Screws

Screws

3 Installtherack-mountbracketsontotheComponent VideoSwitcherwiththesixscrewsdetachedinstep2as shownbelow. Make sure that the rack-mount brackets are installed securely.

Rack-mountbracket (supplied) Screws

Screws

Rack-mountbracket (supplied)

4 MounttheComponentVideoSwitcherintotherackas shownbelow. Make sure that the Component Video Switcher is installed securely.

Rack

POWER

1 2 3 4 5 6 7 8 9 10 11 12

1 2 3 4 5 6 7 8 9 10 11 12

ZONE

SOURCE

Screws(notsupplied)Screws(notsupplied)

Rack

Notes Use the M4 11/32 inch (8mm) screws (attached to the Component

Video Switcher) for installing the rack-mount brackets onto the Component Video Switcher. In case the screws are missing, use M4 screws with a maximum diameter of 1/2 inch (12mm).

Use screws with a minimum diameter of 3/16 inch (4mm) when you mount the Component Video Switcher into the rack.

Make sure you check the rack manufacturers specifications before you mount the Component Video Switcher into the rack. This is to ensure mechanical stability.

This Component Video Switcher requires 2U height when you mount the Component Video Switcher on a standard rack.

10US

SONY CAV-CVS12ES (US) 3-198-136-11(1)

Setting up the Com ponent V

ideo Sw itcher

Hooking up the Component Video Switcher

Before hooking up the Component Video Switcher, be sure the AC power cord is unplugged. Refer to the illustration below for the connection.

Speaker

The CAT5 cable can extend up to 300 feet.

Audio/Video Source1~8

ComponentVideo

AudioL/R

CAV-M1000ES

CAV-M1000ES

CAV-CVS12ES

RS-232Ccable

RS-232Ccable

CAT5cable

ComponentVideoBalun CAV-CVB1

Keypad

Zone1~12Display

Speaker

ComponentVideo cable

Audio/Video Source9~12 (VHS,etc.)

AudioL/R

Composite Video

SONY CAV-CVS12ES (US) 3-198-136-11(1)

11US

Setting up the Com ponent V

ideo Sw itcher

CAT5 RJ45 Video Pinout

The CAT5 RJ45 pinouts use the T568B standard. Refer to the illustration below.

Pinout Wire color

Pin 1 BLUE/Pb (R) White/Orange

Pin 2 BLUE/Pb (T) Orange

Pin 3 GREEN/Y (R) White/Green

Pin 4 GND Blue

Pin 5 +11V White/Blue

Pin 6 GREEN/Y (T) Green

Pin 7 RED/Pr (R) White/Brown

Pin 8 RED/Pr (T) Brown

CAT5 cable

Before installation, be sure to verify the CAT5 wiring connection is correct. Use Category 5e or Category 6 cable.

White/Orange

Wire color

Orange

White/Green

Blue

White/Blue

Green

White/Brown

Brown

1

Pin No.

2

3

4

5

6

7

8

White/Orange

Wire color

Orange

White/Green

Blue

White/Blue

Green

White/Brown

Brown

1

Pin No.

2

3

4

5

6

7

8

CAT5 cable

RJ45 connector

RJ45 connector

12US

SONY CAV-CVS12ES (US) 3-198-136-11(1)

Chapter 3 Other Information This chapter provides additional information that will help you understand and maintain your system.

Precautions

On safety Should any solid object or liquid fall into the cabinet, unplug the

Component Video Switcher and have it checked by a qualified service technician before operating it any further.

On power sources Before operating the unit, check that the operating voltage of the unit

is identical to that of your local power supply. The operating voltage is indicated on the nameplate on the back of the unit.

If you are not going to use the unit for a long time, be sure to disconnect it from the AC power source. To disconnect the lead, grasp the plug itself; never pull the cord.

Install this system so that the power cord can be unplugged from the wall socket immediately in the event of trouble.

On placement Place the unit in a location with adequate ventilation to prevent heat

build-up in the Component Video Switcher. Do not place the unit on a soft surface such as a rug that might block

the ventilation holes on the bottom. Do not place the unit in a location near heat sources, or in a place

subject to direct sunlight, excessive dust, or mechanical shock.

On cleaning Clean the cabinet, panel, and controls with a soft cloth slightly

moistened with a mild detergent solution. Do not use any type of abrasive pad, scouring powder, or solvent, such as alcohol or benzine.

On operation If the system is brought directly from a cold to a warm location,

moisture may condense on the surface of the unit or inside the unit. Should this occur, the system may not operate properly. In this case, turn off and leave the system until the moisture evaporates. Do not use the system until the moisture evaporates, otherwise it may cause a malfunction.

If you have any questions or problems concerning the Component Video Switcher, please consult your nearest Sony dealer.

SONY CAV-CVS12ES (US) 3-198-136-11(1)

O ther Inform

ation

13US

Troubleshooting

If you experience any of the following difficulties while using the Component Video Switcher, use this troubleshooting guide to help you to remedy the problem. Should any problem persist, consult your nearest Sony dealer.

There is no picture, or an unclear picture appears on the TV screen or monitor.

Select the appropriate input on the Main Unit. Set your TV to the appropriate input mode. Move your TV away from the audio components.

The picture does not appear properly. Check that the Component Video Switcher is connected

correctly. For details on how to make the connection, refer to Hooking up the Component Video Switcher on page 10.

The multiple SOURCE indicators blink. Two or more source components are assigned to the

same source number. Set the ASSIGNABLE switch to the appropriate source number.

The source does not change even after turning the SOURCE selector.

Check that you are watching video in the zone indicated by the lit ZONE indicator.

RS-232C does not function. Check that the RS-232C cross cable is used for the

connection. Check that the baud rate setting on the CAV-M1000ES is

set to 9600 bps. Check that the RS-232C commands are correct.

1US

SONY CAV-CVS12ES (US) 3-198-136-11(1)

O ther Inform

ation

Specifications

Video input

Y: 1.0Vp-p/75 ohm

Pb: 0.7Vp-p/75 ohm

Pr: 0.7Vp-p/75 ohm

Video output

CAT5 RJ45 output

General

IR input: accept 40 kHz IR modulation frequency

Power requirements: 120 V AC, 60 Hz

Power consumption: 33 W

Operating temperature: 0C to 40C (32F to 104F)

Dimensions: 435 100 290 mm (17 1/4 4 11 1/2 inches) (w/h/d) (including projecting parts)

Mass: 4.5 kg (9 lbs 15 oz) (excluding AC power cord)

Des

Manualsnet FAQs

If you want to find out how the CAV-CVS12ES Sony works, you can view and download the Sony CAV-CVS12ES Installation Manual on the Manualsnet website.

Yes, we have the Installation Manual for Sony CAV-CVS12ES as well as other Sony manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Installation Manual should include all the details that are needed to use a Sony CAV-CVS12ES. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Sony CAV-CVS12ES Installation Manual is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Sony CAV-CVS12ES Installation Manual consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Sony CAV-CVS12ES Installation Manual free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Sony CAV-CVS12ES Installation Manual, simply download the document to your computer. Once downloaded, open the PDF file and print the Sony CAV-CVS12ES Installation Manual as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.