Sony RM-V401 Operating Instructions PDF
Summary of Content for Sony RM-V401 Operating Instructions PDF
Notes If you are using more than one receiver (or amplifier) and have set
it on the CBL/SAT, CD, AUX or DVD button, when selecting these buttons you cannot control the volume of the receiver (or amplifier) of the RCVR button.
If you change the setting of the RCVR button to a component other than a receiver or amplifier, the volume control setting of video components will return to TV even if you have changed the factory preset volume control. In this case, you will not be able to control the volume from audio components other than a receiver or amplifier.
To reset to factory preset volume control In step 3 above, press VOL instead.
Operating a Component 1 Press the button of the desired
component on the Commander.
2 Point the Commander directly at the component.
3 Press the button for the function you want to use.
See Remote Button Descriptions for complete descriptions of the buttons on the Commander.
Notes on Using the Remote Commander Basically, use this Commander in the same way as the Commanders supplied with your components. Using this Commander will not increase the functions of your
components. The functions of the Commander are limited to the functions of the components themselves. For example, if your TV does not have a MUTING function, the MUTING button on this Commander will not function with your TV.
Some functions of the component may not work with this Commander.
If your cable box can control volume, be sure to set its volume switch to a medium position. If the volume on the cable box is turned down completely, you will not be able to adjust your TVs volume with the Commander.
Setting a channel with a single button (Channel macro function) You can program the Channel Macro function on any of the buttons listed below (macro keys). For example, instead of pressing , , and then ENT button to change the TV channel, you can perform these operations by pressing only the N button.
The macro keys are: N, m, M, x, X, and zREC. (During TV, cable box, or digital satellite receiver operations only.)
The series of operations that can be programmed must be consisted of two to four sequential pressings of to buttons or ENT button.
Note The Channel Macro function may not work correctly for some components.
To program a series of operations
1 Press the desired component select button. (You can select TV, cable box, or digital satellite receiver only.)
2 While pressing the desired macro key, press the buttons required for the operations in sequence. For example, to program t t ENT on the N button, hold down N first, press , , and ENT in sequence, and then release N.
For the customers in the U.S.A. WARNING This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment.
Setting Up the Remote Commander About Presetting the Commander The Commander is preset at the factory to operate Sony brand components. If youre using the Commander with a Sony component, you wont need to preset the Commander before you start using it. To set up the Commander to use with other (non-Sony) manufacturers components, or to use with a component that is not preset at the factory, youll need to follow the instructions in this manual to preset the Commander with the correct code number for your components. (See the supplied Component Code Numbers also.)
Notes The Commander can be set up to operate only one component per
button unless their code numbers happen to be the same. For example, you cannot set up the Commander to operate a Sony TV and a Panasonic TV simultaneously (because they use different code numbers).
You may not be able to operate even a Sony brand component with the factory presetting. In such a case, follow the procedure in Setting the Code.
Remote Button Descriptions
Installing the Batteries Slide open the battery compartment and insert two size AA (R6) batteries (not supplied). Be sure to line up the + and on the batteries with the + and on the battery compartment.
1 2
When to replace the batteries Under normal conditions, batteries will last up to six months. If the Commander does not operate properly, the batteries might be worn out. Replace the batteries with new ones.
Notes Replace both batteries with new ones. Do not take more than 20 minutes to replace the batteries;
otherwise, your setting of the code numbers will be erased.
Notes on Batteries Do not mix old batteries with new ones or mix different types of
batteries together. If the electrolyte inside the battery should leak, wipe the
contaminated area of the battery compartment with a cloth and replace the old batteries with new ones. To prevent the electrolyte from leaking, remove the batteries when you plan not to use the Commander for a long period of time.
Setting the Code Follow the steps 1 and 2 below for each component you plan to use with the Commander.
Step 1: Entering the Code Number
1 See the supplied Component Code numbers, and find the three- digit code number for the desired component. If more than one code number is listed, use the number thats listed first to complete the steps below. For example, if youre setting up a Philips VCR, you would use the code number 035. If your component isnt listed, see Searching for the Correct Code.
2 Press the SET button with a ball-point pen tip etc., and release it.
3 Press the button of the component that you want to set up.
Note On the CBL/SAT, RCVR, CD, AUX, and DVD buttons, cable box, receiver, CD player, tape deck, and DVD player are assigned respectively at the factory. But you can also assign other components on these buttons. For details, see Changing the Component Type on the CBL/SAT, RCVR, CD, AUX, and DVD buttons.
4 Enter the components code number. For example, if youre entering the code for a Philips VCR, you would press
.
5 Press and release the ENT button to store the code number in the Commanders memory.
6 Go to Step 2: Checking if the Code Number Works to finish setting up.
Step 2: Checking if the Code Number Works
1 Power on the component you want to set up.
2 Aim the Remote Commander at the component and press a button to check if that button works. For example, press the POWER button to see if it works on your component .
3 Check that the other buttons of the Commander is operating the corresponding functions of the component.
If the Commander Doesnt Seem to Be Working... First, try repeating these setup procedures using the other codes
listed for your component (see the supplied Component Code Numbers).
If after trying all the codes listed for your component you still cannot get the Commander to work properly, try the search method described in Searching for the Correct Code.
Tip You can write down the code number on the label inside the battery compartment lid.
Searching for the Correct Code If youve tried all the code numbers listed for your component and you still cannot get the Commander to work (or if your component is not listed in the Component Code Numbers tables), try these steps.
1 Power on the component you want to set up. Insert a tape or disc if necessary.
2 Press the SET button with a ball-point pen tip etc., and release it.
3 Press the button of the component on the Commander that you want to set up.
4 Press and release the CH+ button. Then press and release the POWER button.
5 Repeat step 4 until the correct code number is found. Each time you press the CH+ button and then the POWER button, a new code number will be transmitted. Keep trying until your component operates by receiving the transmitted signal from the Commander (e.g., the power turns off, the CH+ function works, playback starts, etc.) Be patient as you do this; it may take about 100 tries until the correct code number is located.
6 When the correct code is found, press the ENT button to store the code number in the Commanders memory.
7 Check that the Commander is operating the other functions of your component by pressing the corresponding buttons on the Commander. If they seem to be working properly, youre done setting up the Commander.
If the component does not operate properly, repeat steps 1 to 6 and search for another code.
If you still cannot get the Commander to work properly, see Troubleshooting.
Changing the Component Type on the CBL/ SAT, RCVR, CD, AUX and DVD buttons At the factory, cable box is assigned on the CBL/SAT button, receiver on the RCVR button, CD player on the CD button, tape deck on the AUX button and DVD player on the DVD button. By completing the following procedure, you can change this setting so that you can set up any component on these buttons.
1 Press the SET button with a ball-point pen tip etc., and release it.
2 Press the CBL/SAT, RCVR, CD, AUX, or DVD button.
3 Press and release the x (stop) button.
4 Press and release one of the following buttons; to assign a VCR to assign a digital satellite receiver to assign a receiver to assign a CD player to assign a tape deck to assign an MD deck or a DAT deck to assign a TV to assign a cable box to assign a DVD player
5 Press and release the ENT button.
6 Enter the components code number by following steps 2 to 6 of Entering the Code Number, or steps 1to 7 of Searching for the Correct Code.
Controlling the Volume of Video Components Connected to an Audio System The Commander is factory preset based on the assumption that you hear the sound of your video components from your TVs speakers, and that you hear the sound of your audio components from the loudspeakers connected to your receiver (or amplifier).
Factory Setting:
* If you assign an audio component on the CBL/SAT, CD, AUX or DVD button, you can control the volume of the receiver (or amplifier) on the RCVR button. If you assign video components on these buttons, you can control the volume of the TV.
Thus you can control the volume of your TV or receiver (or amplifier) while operating a video or audio component without first having to press the TV or RCVR button. For example, to control the volume for your VCR channels, you dont need to press the TV button first. However, if your video components are connected to an audio system, you probably hear your TVs or VCRs sound from the loudspeakers connected to your receiver (or amplifier), not from your TV speakers. In this case, you need to change the factory setting so that you can control the volume of your video components without first having to switch to the receiver (or amplifier). To change the factory setting for the volume control, follow the procedures below.
Note This feature is effective only when a receiver or amplifier is set up on the RCVR button. You cannot control the volume of a receiver (or amplifier) set up on CBL/SAT, CD, AUX or DVD button while operating a component of another button.
Changing the Factory Setting for the Volume Control 1 Press the SET button with a ball-point pen tip, etc. and release it.
2 Press the RCVR button.
3 Press the VOL+ button.
4 Press the ENT button.
The volume control setting is changed to receiver/amplifier. You can control the volume of the receiver (or amplifier) of the RCVR button while selecting any component.
Button
TV
VCR, CBL/SAT*, DVD*
RCVR
CD*, AUX*
Controls the volume of
TV
TV
Receiver (or amplifier)
Receiver (or amplifier) on the RCVR button
Component that can be preset
TV
VCR
Cable box/Digital satellite receiver/ Receiver/CD player/Tape deck/ MD deck/DAT deck/DVD player/ TV/VCR
Button
TV
VCR
CBL/SAT
RCVR
CD
AUX
DVD
Factory setting
Sony TV
Sony VHS VCR
Sony receiver
Sony CD player
Sony tape deck
Sony DVD player
English
3-220-548-11(1)
Remote Commander RM-V401 Operating Instructions Manual de instrucciones (parte posterior) 2000 Sony Corporation Printed in Malaysia
Your Code Number
PIP operations Press To zREC Turn on/off the window picture.* PIP and ENT Turn off the window picture. m or M Change the TV channel in the window picture. PIP and TV/VIDEO Change the input mode of the window picture. x Move the location of the window picture. N Swap the main picture and the window picture. X Freeze the window picture.
Operating a DVD player
3 To select numbers 10 and above. For example, to select track 15, press PIP and then press 5.
4 N: To play. m: To rewind. M: To fast-forward. x: To stop. X: To pause.
5 To display the title menu. 6 To move the cursor upward,
downward, to the left, or to the right.
7 To display the DVD menu. 8 To clear the selected characters
from the screen.
3, 4, and 5 TV: To operate the Picture-in- Picture function. Press each button or combination of buttons as described in the table below. VCR: N: To play. x: To stop. m: To rewind. M: To fast-forward. zREC: To record, press N while pressing z.
6 TV/VCR: To move the cursor upward, downward, to the left, or to the right.
7 TV/VCR: To call up the MENU display.
Specifications Operable distance Approx. 7 m (23 ft) (varies depending of the
component of each manufacturer) Power requirements Two size AA (R6) batteries (not supplied) Battery life Approx. 6 months (varies depending on frequency of
use) Dimensions Approx. 62 207 41 mm (w/h/d)
(2 1/2 8 1/4 1 5/8 in.) Mass Approx. 100 g (3.5 oz.) (not including batteries)
Design and specifications are subject to change without notice.
Operating a TV, VCR, or cable box
General 1 To turn on and off the power of
the selected component. 2 Component select buttons. To
switch to the operations of each component, press the button on which that component is assigned.
9 *Volume up: + Volume down:
q; *To mute the volume on TV or receiver (amplifier).
qs To set up the Commander.
* These buttons control the volume of either TV or receiver (amplifier). See Controlling the Volume of Video Components Connected to an Audio System for details.
qa TV: To display the current channel on TV. VCR: To expose the on-screen display.
qd and qf To change the channel. For example, to change to channel 5, press 0 and 5 (or press 5 and ENT).
qg TV/VCR: To enter the selection. qh TV: To operate SLEEP function
on the TV. (Works only for a TV with the SLEEP function.)
qj Channel up: + Channel down:
qk TV/cable box: To operate JUMP, FLASHBACK or CHANNEL RETURN function on the TV depending on the setting of the TV's manufacturer. VCR: To cancel.
Notes There may be cases you may turn on/off the cable box by pressing the CH+ or
CH buttons on the Commander. If your cable box can control volume, be sure to set its volume control to a
medium position. If the volume on the cable box is turned down completely, you will not be able to adjust your TVs volume with the Commander.
Notes Even if you try to program more than four operations and press the
corresponding buttons in step 2 above, only the first four buttons that were pressed will be programmed.
If you try to program only one operation on a macro key, the setting operation will be rejected.
You can program the Channel Macro function for up to three components only. To program for the fourth component, first clear all macro keys for a component.
To change or clear the program When you want to change the setting or if you are no longer using that programmed operation, follow the procedure below to overwrite or clear the program.
1 Hold down the macro key that you want to change or clear.
2 After waiting for about three seconds, press the new sequence of buttons, or, to clear the program, press and release , and then press and release ENT.
3 Release the macro key.
Note Be sure to wait for about three seconds in step 2 above. While you are holding down the macro key and waiting, the programmed signals are transmitted; therefore, if you are aiming the Commander at your component, the programmed operations may be performed before you go on with the procedure.
Troubleshooting If you have problems setting up or using the Commander: When setting up the Commander, carefully go through the procedures
described in Setting the Code. If the code thats listed first for your component doesnt work, try all the codes for your component - in the order in which theyre listed. If all the codes fail to work (or if your component is not listed in this manual), try using the procedures in Searching for the Correct Code.
Check that youre aiming the Commander directly at the component, and that there are no obstructions between the Commander and the component.
Make sure the batteries youre using are not worn out, and that theyre inserted correctly.
Check that the button of the TV, VCR, CBL/SAT, RCVR, CD, AUX or DVD is pressed to choose your desired component.
Check that the component has infrared remote capability. For example, if your component didnt come with a remote commander, it probably isnt capable of being controlled by a remote commander.
If your video components are connected to an audio system, make sure youve set up the Commander as described in Controlling the Volume of Video Components Connected to an Audio System.
Should any problem persist, reset the Commander to the factory setting by pressing the POWER, TV/VIDEO and VOL buttons simultaneously.
For the customers in the U.S.A. Customer Support Information If after youve read through this manual you still cannot get the Remote Commander to work properly, call the Sony Customer Support Helpline at 1-800-822-2217.
qa To show the current play status on the screen.
qd Number buttons : To set items selected from the screen.
qf To enter the setting. To set items selected from the screen.
qg To execute items selected from the screen.
qh To switch the subtitle. qj To proceed to next/previous
location or song. qk To return to the last previous
screen. ql To change the sound.
* If the window picture does not turn off this way, try pressing ENT while pressing PIP.
Note If you have programmed the Channel Macro function for TV operation, the button used as a macro key cannot be used for PIP operation.
Operating a digital satellite receiver
Operating a tape deck
3, 4, and 5 Tape operation buttons. For dual cassette decks, operation buttons for Deck A (for Sony-brand dual cassette deck, buttons for Deck B). PIP: To reverse. N: To play. m: To rewind. M: To fast-forward. zREC: To record, press N
while pressing zREC. First release N, then release zREC.
x: To stop. X: To pause
6, 7, qf, and qg Operation buttons for Deck B (for Sony-brand dual cassette deck, buttons for Deck A).
3 To use the FAVORITE function.
6 To scroll through the Master Guide.
7 To call up the MENU display. 8 To bring up the Master Guide. qd and qf
To change the channel. For example, to change to channel 5, press 0 and 5 (or press 5 and ENT).
qg To select the channel that's highlighted. To bring up the Station Index when a program guide is not displayed.
qh To bring up the Station Index. qj Channel up: +
Channel down: To page through the guide when a program guide is displayed.
qk To tune to the last tuned station.
ql To switch the output of the digital satellite receiver to the TV. (When you connect a TV cable or antenna to the receiver, the output switches between a TV and SAT program.)
Operating a receiver/amplifier
4 Work as N, M, m, x, X buttons of the CD player. (When a CD player is set up on the CD button.)
qd To select the input source: 1 selects VIDEO 1 2 selects VIDEO 2 3 selects AUX 4 selects TUNER 5 selects CD 6 selects TAPE 7 selects MD 8 selects TV 9 selects PHONO 0 selects DVD
qj Presetting frequency up: +, down: Tuning frequency up: +, down:
qk To shift band (FM/AM). ql To switch input source by each
pressing.
Operating a CD player, an MD deck, or a DAT deck
3 To select numbers 10 and above. For example, to select track 15, press PIP and then press 5.
4 N: To play. m: To select previous track. M: To select next track. x: To stop. X: To pause.
5 MD deck/DAT deck: To record, press N while pressing z/ First release N, then release z.
qd To select the track number. 0 selects track 10. To select track numbers above 10, see the descriptions on the PIP button above.
qk CD player/MD deck: To select next disc.
ENT: To reverse. : To play.
: To rewind. : To fast-forward. : To stop.
MENU: To record, press while pressing MENU. First release , and then release MENU.
OK: To pause. qk To select Deck A or Deck B
(dual cassette deck only).
If your tape decks commander has one set of tape operating buttons, and has an A/B button for the deck selection, use the RECALL button to select Deck A or Deck B.
Control de un componente 1 Presione la tecla correspondiente al
componente deseado del telemando.
2 Apunte con el telemando directamente hacia el componente.
3 Presione la tecla correspondiente a la funcin que desee utilizar.
Con respecto a la descripcin completa de las teclas del telemando, consulte Descripcin de las teclas del telemando.
Notas sobre la utilizacin del telemando Bsicamente, utilice este telemando de la misma forma que el suministrado con sus componentes. La utilizacin de este telemando no aumentar las funciones de sus
componentes. Las funciones del telemando estarn limitadas a las de los propios componentes. Por ejemplo, si su televisor no posee funcin de silenciamiento (MUTING), la tecla MUTING de este telemando no trabajar con su televisor.
Algunas funciones del componente pueden no trabajar con este telemando.
Si su adaptador para cablevisin puede controlar el volumen, cercirese de ajustar su selector de volumen a una posicin intermedia. Si redujese completamente el volumen del adaptador para cablevisin, no podra ajustar el volumen de su televisor con el telemando.
Programacin de un canal en una sola tecla (Funcin de macro de canal) Usted podr programar la funcin de macro de canal en una de las teclas indicadas a continuacin (teclas de macro). Por ejemplo, en vez de presionar las teclas u y despus presionar la tecla ENT para cambiar el canal de televisin, podr realizar estas funciones presionando solamente la tecla N .
Las teclas de macro son: N, m, M, x, X, y zREC. (Durante las operaciones del televisor, el adaptador para cablevisin, o el sintonizador de recepcin va satlite solamente.)
La serie de operaciones que podr programarse deber componerse de dos a cuatro presiones secuenciales de teclas a , o de la tecla ENT.
Nota La funcin de macro de canal puede no trabajar correctamente con algunos componentes.
Para programar una serie de operaciones
1 Presione la tecla selectora correspondiente al componente deseado. (Usted solamente podr seleccionar televisor, adaptador para cablevisin, o sintonizador de recepcin va satlite.)
2 Manteniendo pulsada la tecla de macro deseada, presione secuencialmente las teclas requeridas para la operacin. Por ejemplo, para programar t t ENT en la tecla N, mantenga pulsada N, despus presione secuencialmente , , y ENT, y por ltimo suelte N.
Notas Aunque intente programar ms de cuatro operaciones y presionar
las teclas correspondientes en el paso 2 anterior, solamente se programarn las cuatro teclas presionadas en primer lugar.
Si trata de programar una sola operacin en una tecla de macro, la programaciones rechazar.
Usted podr programar la funcin de macro de canal para tres componentes como mximo. Para programar el cuarto componente, borre en primer lugar todas las teclas para un componente.
Para cambiar o borrar el programa Cuando desee cambiar un ajuste, o si ya no desea utilizar una operacin programada, realice el procedimiento siguiente para rescribir o borrar el programa.
Para los clientes de EE. UU. ADVERTENCIA Este equipo ha sido probado y se ha encontrado que cumple con los lmites para dispositivos digitales de Clase B, de acuerdo con la Parte 15 de las normas de la FCC. Estos lmites han sido diseados para proporcionar una proteccin razonable contra interferencias perjudiciales en una instalacin residencial. Este equipo genera, utiliza, y puede radiar energa de radiofrecuencia y, si no se instala y utiliza de acuerdo con las instrucciones, puede causar interferencias perjudiciales en las radiocomunicaciones. Sin embargo, no existe ninguna garanta de que tales interferencias no se produzcan en una instalacin particular. Si este equipo causa interferencias perjudiciales, lo que podr determinarse desconectando y volviendo a conectar su alimentacin, se ruega que el usuario corrija las interferencias tomando una o ms de las medidas siguientes: Reorientacin o reubicacin de la antena receptora. Aumento de la separacin entre el equipo y el receptor. Conexin del equipo a un tomacorriente diferente del utilizado por
el receptor. Solicitud de ayuda al proveedor o a un tcnico de radio/televisin
experimentado. Tenga en cuenta que cualquier cambio o modificacin no expresamente aprobado en este manual puede anular su autoridad para utilizar este equipo.
Preparacin del telemando Sobre el preajuste del telemando El telemando ha sido preajustado en fbrica para gobernar componentes de marca Sony. Si va a utilizar el telemando con componentes Sony, no necesitar preajustarlo antes de comenzar a utilizarlo. Para ajustar el telemando a fin de utilizarlo con componentes de otros fabricantes (no Sony), o para usarlo con un componente que no haya sido preajustado en fbrica, tendr que seguir las instrucciones de este manual para preajustar el telemando con los nmeros de cdigo correctos para sus componentes. (Consulte tambin los Nmeros de cdigo de componentes suministrados.)
Notas El telemando solamente podr programarse para controlar a la vez
un componente por tecla, a menos que sus nmeros de cdigo sean iguales. Por ejemplo, usted no podr programar el telemando para controlar un televisor Sony y otro Panasonic simultneamente mismo tiempo (porque sus nmeros de cdigo son diferentes).
Quizs no pueda gobernar un componente Sony con el preajuste de fbrica. En tal caso,. realice el procedimiento de Programacin del cdigo.
Colocacin de las pilas Deslice y abra el compartimiento de las pilas, e inserte dos pilas de tamao AA (R6) (no suministradas). Cercirese de alinear + y de las pilas con + y del compartimiento de las mismas.
1 2
Cundo reemplazar las pilas En condiciones normales, las pilas durarn hasta seis meses. Si el telemando no funciona adecuadamente, es posible que las pilas estn agotadas. Reemplace las pilas por otras nuevas.
Notas Reemplace ambas pilas por otras nuevas. No tarde ms de 20 minutos en reemplazar las pilas, porque de lo
contrario su ajuste de nmeros de cdigo se borrar.
Notas sobre las pilas No mezcle una pila nueva con otra vieja, ni dos de tipos diferentes. Si se fuga el electrlito de las pilas, limpie la parte contaminada del
compartimiento de las pilas con un pao y reemplace las pilas viejas por otras nuevas. Para evitar la fuga del electrlito, extraiga las pilas cuando no vaya a utilizar el telemando durante mucho tiempo.
Programacin del cdigo Realice los pasos 1 y 2 siguientes para cada componente que planee utilizar con el telemando.
Paso 1: Introduccin del nmero de cdigo
1 Consulte los Nmeros de cdigo de componentes suministrados, y busque el nmero de cdigo de tres cifras para el componente deseado. Si hay ms de un nmero de cdigo en la lista, utilice el primero de ellos para completar los pasos siguientes. Por ejemplo, para una videograbadora Philips, utilice el nmero de cdigo 035. Si su componente no est en la lista, consulte Bsqueda del cdigo correcto.
2 Presione el botn SET con un bolgrafo, etc., y sultelo.
3 Presione la tecla del componente que desee ajustar.
Nota En las teclas CBL/SAT, RCVR, CD, AUX, y DVD se han asignado respectivamente en la fbrica adaptador para cablevisin, receptor, reproductor de discos compactos, deck de cassettes, y reproductor de discos DVD. Pero usted tambin podr asignar otros componentes a estas teclas. Con respecto a los detalles, consulte Cambio del tipo de componentes de las teclas CBL/SAT, RCVR, CD, AUX, y DVD.
4 Introduzca el nmero de cdigo del componente. Por ejemplo, para introducir el cdigo para una videograbadora Philips, presione
.
5 Presione la tecla ENT para almacenar el nmero de cdigo en la memoria del telemando.
6 Para finalizar la programacin, vaya al Paso 2: Comprobacin del funcionamiento de un nmero de cdigo.
Paso 2: Comprobacin del funcionamiento de un nmero de cdigo
1 Conecte la alimentacin del componente que desee ajustar.
2 Apunte con el telemando hacia el componente y presione una tecla para comprobar si trabaja. Por ejemplo, presione la tecla POWER para ver si trabaja en su componrente.
3 Compruebe si las otras teclas del telemando controlan las funciones correspondientes del componente.
Si el telemando parece que no trabaja... En primer lugar, repita estos procedimientos de programacin
utilizando los otros cdigos de la lista para su componente (consulte las tablas de Nmeros de cdigo de componentes).
Si, despus de haber probado todos los cdigos de la lista para su componente, el telemando sigue sin trabajar adecuadamente, consulte Bsqueda del cdigo correcto.
Sugerencia Usted podr escribir el nmero de cdigo en la etiqueta del interior de la tapa del compartimiento de la batera.
Bsqueda del cdigo correcto Si ha intentado todos lo nmeros de cdigo de la lista para su componente y el telemando sigue sin trabajar (o si sus componentes no estn indicados en las tablas de Nmeros de cdigo de componentes), pruebe estos puntos.
1 Conecte la alimentacin del componente que desee ajustar. Si es necesario, inserte un cassette o un disco.
2 Presione el botn SET con un bolgrafo, etc., y sultelo.
3 Presione la tecla del componente que desee ajustar.
4 Presione y suelte la tecla CH+. Despus presione y suelte la tecla POWER.
5 Repita el paso 4 hasta que encuentre el nmero de cdigo correcto. Cada vez que presione la tecla CH+ y despus la tecla POWER, se transmitir un nuevo nmero de cdigo. Contine intentndolo hasta que su componente funcione al recibir la seal transmitida desde el telemando (p. ej., se desconecta la alimentacin, la funcin de CH+ trabaja, se inicia la reproduccin, etc.). Tenga paciencia cuando realice esto, porque es posible que tenga que realizar 100 intentos hasta encontrar el nmero de cdigo correcto.
6 Cuando encuentre el cdigo correcto, presione la tecla ENT para almacenar el nmero de cdigo en la memoria del telemando.
7 Compruebe si el telemando controla las otras funciones de su componente presionando las teclas correspondientes de dicho telemando. Si parece trabajar correctamente, habr finalizado el preajuste del telemando.
Si el componente no funciona correctamente, repita los pasos 1 a 6 y busque otro cdigo.
Si el telemando sigue sin trabajar adecuadamente, consulte Solucin de problemas.
Cambio del tipo de componente de las teclas CBL/SAT, RCVR, CD, AUX, y DVD En la fbrica adaptador para cablevisin se ha asignado a la tecla CBL/SAT, receptor a la tecla RCVR, reproductor de discos compactos a la tecla CD, deck de cassettes a la tecla AUX , y el reproductor de discos DVD en la tecla DVD.
1 Presione el botn SET con un bolgrafo, etc., y sultelo.
2 Presione la tecla CBL/SAT, RCVR, CD, AUX, o DVD.
3 Presione y suelte la tecla x (parada).
4 Presione y suelte una de las teclas siguientes; para asignar una videograbadora para asignar un sintonizador de recepcin va satlite digital para asignar un receptor para asignar un reproductor de discos compactos para asignar un deck de cassettes para asignar un deck de minidiscos o un deck de cinta audiodigital
para asignar un televisor para asignar un adaptador para cablevisin Para asignar un reproductor de discos DVD
5 Presione u suelte la tecla ENT.
6 Introduzca el nmero de cdigo del componente siguiendo los pasos 2 a 6 de Introduccin del nmero de cdigo, o los pasos 1 a 7 de Bsqueda del cdigo correcto.
Control del volumen de los componentes de vdeo conectados a un sistema de audio El mando a distancia ha sido programado en fbrica suponiendo que usted va a escuchar el sonido de sus componentes de vdeo a travs de los altavoces de su televisor, y el sonido de sus componentes de audio a travs de los altavoces conectados a su receptor (o amplificador).
Ajuste de fbrica:
* Si ha asignado componentes de audio a la tecla CBL/SAT, CD, AUX,o DVD, podr controlar el volumen del receptor (o del amplificador) con la tecla RCVR. Si ha asignado componentes de vdeo a estas teclas, podr controlar el volumen del televisor.
De esta forma, usted podr controlar el volumen de su televisor o receptor (o amplificador) mientras utilice un componente de vdeo o de audio sin tener que presionar primero la tecla TV o RCVR. Por ejemplo, para controlar el volumen de los canales de su videograbadora, no necesitar presionar en primer lugar la tecla TV. Sin embargo, si sus componentes de vdeo estn conectados a un sistema de audio, probablemente escuchar el sonido de su televisor o de su videograbadora a travs de los altavoces conectados a su receptor (o amplificador), no a travs de los altavoces de su televisor. En este caso, tendr que cambiar el ajuste de fbrica a fin de poder controlar el volumen de sus componentes de vdeo sin tener que cambiar primero al receptor (o amplificador). Para cambiar el ajuste de fbrica para controlar el volumen, realice los procedimientos siguientes.
Nota Esta funcin solamente trabajar cuando haya programado un receptor o amplificador en la tecla RCVR. Usted no podr controlar el volumen de un receptor (o amplificador) programado en la tecla CBL/SAT, CD, AUX,ni DVD mientras utilice otro componente en otra tecla distinta.
Cambio del ajuste de fbrica para el control de volumen 1 Presione el botn SET con un bolgrafo, etc., y sultelo.
2 Presione el botn RCVR.
3 Presione la tecla VOL+.
4 Presione la tecla ENT.
El ajuste del control de volumen cambiar a receptor/ amplificador. Usted podr controlar el volumen del receptor (o amplificador) de la tecla RCVR aunque haya seleccionado cualquier otro componente.
Notas Si est utilizando ms de un receptor (o amplificador) y lo ha
programado en la tecla CBL/SAT, CD, AUX, o DVD, cuando seleccione estas teclas, no podr controlar el volumen del receptor (o amplificador) de la tecla RCVR.
Si cambia el ajuste de la tecla RCVR a un componente que no sea un receptor o amplificador, el ajuste del control de volumen de los componentes de vdeo volver a TV incluso aunque haya cambiado el control de volumen ajustado en fbrica. En este caso, no podr controlar el volumen desde componentes de audio que no sean un receptor o un amplificador.
Para reponer el control de volumen al ajuste de fbrica En el paso 3 anterior, presione en su lugar VOL.
Tecla
TV
VCR, CBL/SAT*, DVD*
RCVR
CD*, AUX*
Controla el volumen del
Televisor
Televisor
Receptor (o amplificador)
Receptor (o amplificador) en la tecla RCVR
Componente a programar
Televisor
Videograbadora
Adaptador para cablevisin/ Sintonizador de recepcin va satlite digital/Receptor/ Reproductor de discos compactos/Deck de cassettes/ Deck de minidiscos/Deck de cinta audiodigital/Reproductor de discos DVD/Televisor/ Videograbadora
Tecla
TV
VCR
CBL/SAT
RCVR
CD
AUX
DVD
Ajuste de fbrica
Televisor Sony
Videograbadora VHS Sony
Receptor Sony
Reproductor de discos compactos Sony
Deck de cassettes Sony
Reprosuctor de discos DVD SONY
Espaol 1 Mantenga presionada la tecla de macro cuyos datos desee cambiar o borrar.
2 Despus de esperar unos tres segundos presione la nueva secuencia de teclas o, si desea borrar el programa, presione y suelte , y despus presione y suelte ENT.
3 Suelte la tecla de macro.
Nota Cercirese de esperar unos tres segundos en el paso 2 anterior. Mientras mantenga presionada la tecla de macro, se transmitirn las seales programadas, motivo por el que si est apuntando con el telemando hacia su componente, las operaciones programadas pueden realizarse antes de entrar en el procediiento.
Solucin de problemas Si tiene problemas al programar o utilizar el telemando: Cuando programe el telemando, siga cuidadosamente los procedimientos
descritos en Programacin del cdigo. Si el primer cdigo de la lista para su componente no trabaja, pruebe los dems de la lista para dicho componente, en el orden de la lista. Si no trabaja ninguno de los cdigos (o si su componente no est en la lista de este manual), pruebe los procedimientos de Bsqueda del cdigo correcto.
Compruebe si est apuntando directamente hacia el componente, y que no haya obstculos entre el telemando y el componente.
Cercirese de que las pilas que est utilizando no estn agotadas y de que estn insertadas correctamente.
Compruebe si ha presionado la tecla TV, VCR, CBL/SAT, RCVR, CD, AUX, o DVD del telemando correspondiente al componente deseado.
Compruebe que el componente pueda controlarse con rayos infrarrojos. Por ejemplo, si su componente no vino con telemando, probablemente no podr controlarse con un telemando.
Si sus componentes de vdeo estn conectados a un sistema de audio, cercirese de que ha programado el telemando como se describe en Control del volumen de componentes de vdeo conectados a un sistema de audio.
Si el problema persiste, reponga el telemando a los ajustes de fbrica presionando simultneamente las teclas POWER, TV/VIDEO y VOL.
Para los clientes de EE.UU. Informacin para ayuda a los clientes Si despus de haber ledo este manual, el telemando sigue sin funcionar adecuadamente, llame a Customer Support Helpline, 1-800-822-2217.
Su nmero de cdigo
Descripcin de las teclas del telemando
Operaciones de PIP Presione Para zREC activar/desactivar la imagen de la ventanilla.* PIP y ENT desactivar la imagen de la ventanilla. m o M cambiar el canal de televisin de la imagen de la
ventanilla. PIP y TV/VIDEO cambiar el modo de entrada de la imagen de la
ventanilla. x cambiar la ubicacin de la imagen de la ventanilla. N intercambiar la imagen principal por la de la
ventanilla. X congelar la imagen de la ventanilla.
Control de un reproductor de discos DVD 3 Para seleccionar 10 y nmeros
superiores. Por ejemplo, para seleccionar la cancin 15, presione PIP y despus 5.
4 N: Para reproducir. m: Para rebobinar la cinta. M: Para hacer que la cinta
avance rpidamente. x: Para parar. X: Para realizar una pausa.
5 Para hacer que se visualice el men de ttulos.
6 Para mover el cursor hacia arriba, hacia abajo, hacia la izquierda, o hacia la derecha.
7 Para hacer que se visualice el men de un disco DVD.
3, 4, y 5 TV (Televisor): Para utilizar la funcn de imagen en imagen. Presione cada tecla, o combinacin de teclas, como se describe en la tabla siguiente. VCR (Videograbadora): N: Para reproducir. x: Para parar. m: Para rebobinar la cinta. M: Para hacer que la cinta
avance rpidamente. zREC: Para grabar, presione N
manteniendo pulsadag z. 6 TV/VCR: Para mover el cursor
hacia arriba, hacia abajo, hacia la izquierda, o hacia la derecha.
7 TV/VCR: Para invocar la visualizacon de MENU.
qa TV: Para hacer que se visualice el canal actual en el televisor. VCR: Para hacer que se visualicen las indicaciones en pantalla.
Control de un televisor (TV), videograbadora (VCR) o adaptador para cablevisin
General 1 Para conectar y desconectar la
alimentacin del componente seleccionado.
2 Teclas selectoras de componentes. Para cambiar a las operaciones de cada componente, presione la tecla a la que haya asignado el componente.
9 *Para aumentar el volumen: + Para reducir el volumen:
q; *Para silenciar el volumen del televisor o del receptor (amplificador).
qs Para programar el telemando.
* Controlan el volumen del televisor o del receptor (amplificador). Con respecto a los detalles, consulte Control del volumen de los componentes de vdeo conectados a un sistema de audio.
qd y qf Para cambiar el canal. Por ejemplo, para cambiar al canal 5, presione 0 y 5 (o presione 5 y ENT).
qg TV/VCR: Para introducir la seleccin.
qh TV: Para controlar la funcin de cronodesconexin (SLEEP) del televisor. (Solamente trabajar si el televisor posee tal funcin.)
qj Para pasar a canales superiores: + Para pasar a canales inferiores:
qk TV/adaptador para cablevison: Para controlar la funcin de cambio entre dos canales (JUMP, FLASHBACK o CHANNEL RETURN) del televisor, dependiendo del ajuste del fabricante de dicho televisor. VCR: Para cancelar
Notas Puede darse el caso de que resulte imposible conectar/desconectar la
alimentacin del adaptador para cablevisin presionando la tecla CH+ o CH del telemando.
Si su adaptador para cablevisin puede controlar el volumen, cercirese de ajustar su selector de volumen a una posicin intermedia. Si redujese completamente el volumen del adaptador para cablevisin, no podra ajustar el volumen de su televisor con el telemando.
8 Para borrar los caracteres seleccionados de la pantalla.
qa Para hacer que en la pantalla aparezca el estado de reproduccin actual.
qd Teclas numricas: Para establecer los elementos seleccionados de la pantalla.
qf Para introducir un ajuste o para establecer los elementos seleccionados de la pantalla.
qg Para ejecutar los elementos seleccionados de la pantalla.
qh Para cambiar el subttulo. qj Para localizar a cancin anterior/
siguiente qk Para volver a la pantalla anterior. ql Para cambiar el sonido.
* Si la imagen de la ventanilla no se desactiva de esta forma, pruebe presionando ENT manteniendo pulsada PIP.
Nota Si ha programado la funcin de macro de canal para la operacin de un televisor en una tecla utilizada como tecla de macro, no podr usar la funcin de PIP.
Control de un sintonizador de recepcin va satlite digital
Control de un deck de cassettes 3, 4, y 5
Teclas de operacin del deck de cassettes. Para decks de doble cassette, teclas de operacin para el deck A (para decks de cassettes Sony, teclas para el deck B). PIP: Para cambiar de cara N: Para reproducir. m: Para rebobinar la cinta. M: Para hacer que la cinta
avance rpidamente. zREC: Para grabar, presione N
manteniendo pulsada zREC. Suelte primero N, y despus zREC.
x: Para parar. X: Para realizar una pausa.
6, 7, qf, y qg Teclas de operacin para el deck B (para decks de cassettes Sony, teclas para el deck A)
3 Para utilizar la funcin FAVORITE.
6 Para desplazarse por la Gua principal.
7 Para invocar la visualizacin de MENU.
8 Para hacer que aparezca la Gua principal.
qd y qf Para cambiar el canal. Por ejemplo, para cambiar al canal 5, presione 0 y 5 (o presiones 5 y ENT).
qg Para seleccionar el canal resaltado. Para hacer que se visualice el ndice de emisoras cuando no se visualice una gua de programas.
qh Para hacer que se visualice el ndice de emisoras.
qj Para pasar a canales superiores: + Para pasar a canales inferiores: Para desplazarse por las pginas de la gua cuando se est visualizando una gua de programas.
qk Para sintonizar la ltima emisora recibida.
ql Para cambiar la salida del sintonizador de recepcin va satlite digital al televisor. (Cuando haya conectado un sistema de cablevisin o una antena de televisin al receptor de radiodifusin digital, la salida cambiar entre los programas del televisor y los del sistema de SAT digital).
Control de un receptor/amplificador
Control de un reproductor de discos compactos (CD), de un deck de minidiscos, o de un deck de cinta audiodigital. 3 Para seleccionar 10 y nmeros
superiores. Por ejemplo, para seleccionar la cancin 15, presione PIP y despus 5.
4 N: Para reproducir. m: Para seleccionar la cancin
anterior. M: Para seleccionar la cancin
siguiente. x: Para parar. X: Para realizar una pausa.
5 Deck de minidiscos/deck de cinta audiodigital: Para grabar, presione N manteniendo pulsada z/Suelte primero N, y despus z.
qd Para seleccionar el nmero de cancin. 0 selecciona la cancin 10. Para seleccionar nmeros de canciones superiores a 10, consulte las descripciones de la tecla PIP ofrecidas anteriormente.
qk Reproductor de discos compactos/deck de minidiscos: Para seleccionar el disco siguiente.
ENT: Para cambiar de cara : Para reproducir.
: Para rebobinar la cinta. : Para hacer que la cinta avance
rpidamente. : Para parar.
MENU: Para grabar, presione manteniendo pulsada MENU. Suelte primero
, y despus MENU. OK: Para realizar una pausa.
qk Para seleccionar Deck A o Deck B (deck de cassette doble solamente).
Si el telemando de su deck posee un juego de teclas de operacin de la cinta, y tiene tecla A/B para la seleccin del deck, utilice la tecla RECALL para seleccionar el deck A o el B.
4 Trabajan como las teclas N, M, m, x, y X del reproductor de discos compactos. (Cuando el reproductor de discos compactos est ajustado en la tecla CD.)
qd Para seleccionar la fuente de entradae: 1 selecciona el equipo de vdeo 1
(VIDEO 1) 2 selecciona el equipo de vdeo 2
(VIDEO 2) 3 para seleccionar el deck de
cassettes y el sentido de movimiento de la cinta (AUX)
4 selecciona el sintonizador (TUNER)
5 Selecciona CD 6 selecciona TAPE 7 selecciona MD 8 selecciona el televisor (TV) 9 selecciona PHONO 0 selecciona DVD
qj Para memorizar frecuencias superiores: +, inferiores: Para sintonizar frecuencias superiores: +,inferiores:
qk Para cambiar de banda (FM/AM). ql Para cambiar la fuente de entrada
con cada presin.
Especificaciones Alcance de control Aprox. 7 m (puede variar dependiendo del
componente de cada fabricante) Alimentacin Dos de tamao AA (R6) (no suministradas) Duracin d
Related manuals for Sony RM-V401 Operating Instructions
Manualsnet FAQs
If you want to find out how the RM-V401 Sony works, you can view and download the Sony RM-V401 Operating Instructions on the Manualsnet website.
Yes, we have the Operating Instructions for Sony RM-V401 as well as other Sony manuals. All you need to do is to use our search bar and find the user manual that you are looking for.
The Operating Instructions should include all the details that are needed to use a Sony RM-V401. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.
The best way to navigate the Sony RM-V401 Operating Instructions is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.
This Sony RM-V401 Operating Instructions consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.
You can download Sony RM-V401 Operating Instructions free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.
To be able to print Sony RM-V401 Operating Instructions, simply download the document to your computer. Once downloaded, open the PDF file and print the Sony RM-V401 Operating Instructions as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.