Contents

Sony BDP-S301 Operating Instructions PDF

1 of 72
1 of 72

Summary of Content for Sony BDP-S301 Operating Instructions PDF

Actual total number: PANTONE 2925C Sony BDP-S300/301(US) 3-196-787-13 (1)

3-196-787-13(1)

2007 Sony Corporation

3-196-787-13 (1)

B l u - r a y D i s c P l a y e r B D P - S 3 0 0 B D P - S 3 0 1

Printed in Japan

O p e r a t i n g I n s t r u c t i o n s

TM

Printed on 70% or more recycled paper using VOC (Volatile Organic Compound)- free vegetable oil based ink.

2

WARNING

To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only. The AC power cord must be changed only at a qualified service shop. Batteries or batteries installed apparatus shall not be exposed to excessive heat such as sunshine, fire or the like.

CAUTION The use of optical instruments with this product will increase eye hazard. As the laser beam used in this Blu-ray Disc player is harmful to eyes, do not attempt to disassemble the cabinet. Refer servicing to qualified personnel only.

This label is located on the laser protective housing inside the enclosure.

This symbol is intended to alert the user to the presence of uninsulated dangerous voltage within the products enclosure that may be of sufficient magnitude to constitute a risk

of electric shock to persons.

This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

CAUTION You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment.

Note This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and

receiver. Connect the equipment into an outlet on a circuit

different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

For customers in the U.S.A If this product is not working properly, please call 1- 800-222-7669. Owners Record The model and serial numbers are located at the rear of the unit. Record the serial number in the space provided below. Refer to them whenever you call upon your Sony dealer regarding this product.

Model No. BDP-S300 BDP-S301

Serial No.______________

For Customers in Canada If this product is not working properly, please call 1- 877-602-2008 for Peace of Mind Warranty Replacement service. For other product related questions please contact our Customer Information Service Center at 1-877-899-7669 or write to us at: Customer Information Service 115 Gordon Baker Road, Toronto, Ontario, M2H 3R6

Notes About the Discs

To keep the disc clean, handle the disc by its edge. Do not touch the surface. Dust, fingerprints, or scratches on the disc may cause it to malfunction.

Do not expose the disc to direct sunlight or heat sources such as hot air ducts, or leave it in a car parked in direct sunlight as the temperature may rise considerably inside the car.

After playing, store the disc in its case. Clean the disc with a cleaning cloth.

Wipe the disc from the center out.

Do not use solvents such as benzine, thinner, commercially available disc/ lens cleaners, or anti-static spray intended for vinyl LPs.

If you have printed the discs label, dry the label before playing.

Important Safety Instructions

1) Read these instructions. 2) Keep these instructions. 3) Heed all warnings. 4) Follow all instructions. 5) Do not use this apparatus near water. 6) Clean only with dry cloth. 7) Do not block any ventilation

openings. Install in accordance with the manufacturers instructions.

8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

9) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10) Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11) Only use attachments/accessories specified by the manufacturer.

12) Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/ apparatus combination to avoid injury from tip-over.

13) Unplug this apparatus during lightning storms or when unused for long periods of time.

14) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

Precautions

On safety To prevent fire or shock hazard, do not

place objects filled with liquids, such as vases, on the apparatus.

Should any solid object or liquid fall into the cabinet, unplug the player and have it checked by qualified personnel before operating it any further.

On power sources The player is not disconnected from the

AC power source (mains) as long as it is connected to the wall outlet, even if the player itself has been turned off.

If you are not going to use the player for a long time, be sure to disconnect the player from the wall outlet. To disconnect the AC power cord, grasp the plug itself; never pull the cord.

On placement Place the player in a location with

adequate ventilation to prevent heat build-up in the player.

Do not place the player on a soft surface such as a rug that might block the ventilation holes.

Do not place the player in a location near heat sources, or in a place subject to direct sunlight, excessive dust, or mechanical shock.

Do not install the player in an inclined position. It is designed to be operated in a horizontal position only.

Keep the player and the discs away from equipment with strong magnets, such as microwave ovens, or large loudspeakers.

Do not place heavy objects on the player.

Do not install this player in a confined space, such as a bookshelf or similar unit.

Install this player so that the power cord can be unplugged from the wall socket immediately in the event of trouble.

On operation If the player is brought directly from a

cold to a warm location, or is placed in a very damp room, moisture may condense on the lenses inside the player. Should this occur, the player may not operate properly. In this case, remove the disc and leave the player turned on for about half an hour until the moisture evaporates.

When you move the player, take out any discs. If you dont, the disc may be damaged.

On adjusting volume Do not turn up the volume while listening to a section with very low level inputs or no audio signals. If you do, the speakers may be damaged when a peak level section is played.

On cleaning Clean the cabinet, panel, and controls with a soft cloth slightly moistened with a mild detergent solution. Moreover, wipe the glass part on the front panel with a soft, dry cloth. Do not use any type of abrasive pad, scouring powder or solvent such as alcohol or benzine.

On cleaning discs, disc/lens cleaners Do not use cleaning discs or disc/lens cleaners (including wet or spray types). These may cause the apparatus to malfunction.

On replacement of parts In the events that this player is repaired, repaired parts may be collected for reuse or recycling purposes.

IMPORTANT NOTICE Caution: This player is capable of holding a still video image or on-screen display image on your television screen indefinitely. If you leave the still video image or on-screen display image displayed on your TV for an extended period of time you risk permanent damage to your television screen. Plasma display panel televisions and projection televisions are susceptible to this.

3

4

Table of Contents

WARNING ...............................................................2 Notes About the Discs ........................................2 Important Safety Instructions ...........................3 Precautions ...........................................................3 Table of Contents .................................................4

About this manual ................................................5 This Player Can Play the Following

Discs and Files ................................................5 Examples of discs that the player cannot play .....6 About playback of discs recorded in AVCHD

format .............................................................6 BD/DVD region code ...........................................7 Note on playback operations of BDs/DVDs .........7 Copyrights ............................................................7

Main Features .......................................................7

Getting Started Step 1: Unpacking ...............................................9 Step 2: Connecting the Video Cords/HDMI

Cord .................................................................10 A Connecting to a video input jack ...................10 B Connecting to an S VIDEO input jack ...........10 C Connecting to component video input jacks

(Y, PB, PR) ....................................................10 D Connecting to an HDMI input jack ................11 About the BRAVIA Theatre Sync features

(for HDMI connections only) .........................11 Step 3: Connecting the Audio Cords ............12

Connecting to your TV ..............................13 Connecting to a stereo amplifier (receiver)

and 2 speakers .............................................13 Connecting to an AV amplifier (receiver)

having a Dolby Surround (Pro Logic) decoder and 3 to 6 speakers ........................14

Connecting to an AV amplifier (receiver) with 5.1ch input jacks and 6 speakers .........14

Connecting to an AV amplifier (receiver) with a digital input jack and 6 speakers ........15

Connecting to an AV amplifier (receiver) with an HDMI input jack and 8 speakers ......15

Step 4: Connecting the Power Cord .............16 Step 5: Preparing the Remote ........................16

If you want to control your TV with the supplied remote ..........................................................17

Step 6: Easy Setup ............................................18 Step 7: Additional Adjustments .....................19

Basic Operations Playing a Disc .....................................................20 Guide to Displays ...............................................22

Entering characters ............................................23 Guide to the Remote .........................................24

Playing in various play mode .............................25 Searching using the remote ...............................26

Checking the Disc Information .......................26 Clarifying Low Volume Sounds

(Audio DRC) ...................................................27

Adjusting the Pictures ......................................28 Fine-tuning the picture to your preference .........28

Locking a Disc ....................................................29 Setting/changing the password ..........................29 Setting the Parental Control for DVD VIDEOs ...30 Setting the Parental Control for BD-ROMs ........30

Watching Movie Files Viewing All Titles ...............................................32

Playing a title .....................................................33 Browsing by Genre, Quicklist, or Folder .....34 Searching for a Title ..........................................34 Programming Playback (Quicklist) ...............35

Listening to Music Files Viewing All Artists .............................................36

Playing a track ...................................................37 Browsing by Artist, Album, Genre,

Quicklist, or Folder ......................................38 Searching for a Track .......................................38 Programming Playback (Quicklist) ...............39

Viewing Photo Files Viewing All Folders ...........................................40

Playing a slideshow ...........................................41 Browsing by Date, Quicklist, or Folder ........42 Searching for a Photo .......................................42 Programming a Slideshow Playback

(Quicklist) .......................................................43

Changing the Initial Settings Using the Setup Displays ................................44 Video Setup .........................................................45 Audio Setup .........................................................47 Language .............................................................49 Parental Control .................................................50 Speakers ...............................................................51 Options .................................................................52 Resetting the Player ..........................................53

Additional Information Troubleshooting .................................................54 Self-Diagnosis Function ...................................57 Index to Parts and Controls ............................58

Front panel .........................................................58 Front panel display ............................................59 Rear panel .........................................................59

GNU License Information ................................60 Glossary ...............................................................66 Specifications .....................................................67 Language Code List ..........................................68 Parental Control Country/Area Code List ...69 Index ......................................................................70

A

B

C

D-1

D-2

D-3

ntinued

About this manual Instructions in this manual describe the controls on the remote. You can also use the controls on the player if they have the same or similar names as those on the remote. The meanings of the icons used in this manual are described below:

*1 BD-REs/BD-Rs in BDMV mode only. *2 MP3 (MPEG-1 Audio Layer III) is a standard format defined by ISO

(International Organization for Standardization)/IEC (International Electrotechnical Commission) MPEG which compresses audio data.

Note The on-screen display illustrations used in this manual may not match the graphics displayed on your TV screen.

This Player Can Play the Following Discs and Files

Blu-ray Disc is a trademark. Blu-ray Disc, DVD+RW, DVD-RW, DVD+R, DVD- R, DVD VIDEO, and CD logos are trademarks.

Supported file formats (DATA DVD only) DVD+RWs/DVD-RWs/DVD+Rs/DVD-Rs are called DATA DVD in this manual when the discs contain playable files. The following file formats are supported: MPEG-2 PS movie files. MP3 music files. JPEG* image files. * JPEG format conforming to UDF (Universal Disk Format).

Notes about BD-ROM compatibility This player supports BD-ROM Profile 1 only. Playback of later versions and BDs other than BD-ROM is not guaranteed. Since the Blu-ray Disc specifications are new and evolving, some discs may not play depending on the disc type and the version. The audio output differs depending on the source, connected output jack, and selected audio settings. For details, see page 48.

Icon Meaning

Functions available for BD-ROMs and BD-REs/BD-Rs*1, including DL discs.

Functions available for DVD VIDEOs and DVD+RWs/DVD+Rs in +VR mode or DVD-RWs/DVD-Rs in video mode, including 8 cm discs.

Functions available for DATA DVDs (DVD+RWs/DVD+Rs/DVD-RWs/DVD- Rs containing MPEG-2 PS movie files, MP3*2 audio tracks, and JPEG image files).

Functions available for music CDs or CD- Rs/CD-RWs in music CD Format.

BD

DVD

DATA DVD

CD

Disc Format

Blu-ray Disc

DVD VIDEO

DVD-RW/-R

DVD+RW/+R

CD

,co

5

6

Examples of discs that the player cannot play

The player cannot play the following discs: BDs with cartridge. DVD-RWs/DVD-Rs of VR mode. DVD-RAMs. HD DVDs. DVD Audio discs. DATA CDs (CD-Rs/CD-RWs other than music CD format). CD-ROMs recorded in PHOTO CD format. Data part of CD-Extras. VCDs/Super VCDs. HD layer on Super Audio CDs.

Also, the player cannot play the following discs: A BD-ROM/DVD VIDEO with a different region code. A disc recorded in a color system other than NTSC, such as

PAL (this player conforms to the NTSC color system). A disc that has a non-standard shape (e.g., card, heart). A disc with paper or stickers on it. A disc that has the adhesive of cellophane tape or a sticker still

left on it.

Notes Notes about BD-REs/BD-Rs, DVD+RWs/DVD+Rs, DVD-RWs/

DVD-Rs, or CD-Rs/CD-RWs Some BD-REs/BD-Rs, DVD+RWs/DVD+Rs, DVD-RWs/ DVD-Rs, or CD-Rs/CD-RWs cannot be played on this player due to the recording quality or physical condition of the disc, or the characteristics of the recording device and authoring software. The DVD disc will not play if it has not been correctly finalized. For more information, refer to the operating instructions for the recording device. Note that some playback functions may not work with some DVD+RWs/DVD+Rs, even if they have been correctly finalized. In this case, view the disc by normal playback.

Music discs encoded with copyright protection technologies This product is designed to playback discs that conform to the Compact Disc (CD) standard. Recently, various music discs encoded with copyright protection technologies are being marketed by some record companies. Please be aware that among those discs, there are some that do not conform to the CD standard and may not be playable by this product.

Note on DualDiscs A DualDisc is a two sided disc product which mates DVD recorded material on one side with digital audio material on the other side. However, since the audio material side does not conform to the Compact Disc (CD) standard, playback on this product is not guaranteed.

Note about double-layer DVDs The playback pictures and sound may be momentarily interrupted when the layers switch.

Note about 8 cm BD-REs/8 cm BD-Rs Some 8 cm BD-REs/8 cm BD-Rs cannot be played on this player.

About playback of discs recorded in AVCHD format

This player can play AVCHD format discs.

What is the AVCHD format? The AVCHD format is a high definition digital video camera format used to record SD (standard definition) or HD (high definition) signals of either the 1080i specification*1 or the 720p specification*2 on DVDs, using efficient data compression coding technology. The MPEG-4 AVC/H.264 format is adopted to compress video data, and the Dolby Digital or Linear PCM system is used to compress audio data. The MPEG-4 AVC/ H.264 format is capable of compressing images at higher efficiency than that of the conventional image compressing format. The MPEG-4 AVC/H.264 format enables a high definition (HD) video signal shot on a digital video camera recorder to be recorded on DVD discs, in the same way as it would be for a standard definition (SD) television signal.

AVCHD and the AVCHD logo are trademarks of Matsushita Electric Industrial Co., Ltd. and Sony Corporation.

*1 A high definition specification which utilizes 1080 effective scanning lines and the interlace system.

*2 A high definition specification which utilizes 720 effective scanning lines and the progressive system.

Notes Some AVCHD format discs may not play, depending on the recording

condition. The AVCHD format disc will not play if it has not been correctly

finalized.

TM

ntinued

BD/DVD region code Your player has a region code printed on the back of the unit and only will play BD-ROM/DVD VIDEOs (playback only) labeled with identical region codes. This system is used to protect copyrights.

DVD VIDEOs labeled will also play on this player.

Depending on the BD-ROM/DVD VIDEO, there may be no region code indication, even though playing the BD-ROM/DVD VIDEO is prohibited by area restrictions.

Note on playback operations of BDs/ DVDs

Some playback operations of BDs/DVDs may be intentionally set by software producers. Since this player plays BDs/DVDs according to the disc contents the software producers designed, some playback features may not be available. Also, refer to the instructions supplied with the BDs/DVDs.

Copyrights This product incorporates copyright protection technology that is protected by U.S. patents and other intellectual property rights. Use of this copyright protection technology must be authorized by Macrovision, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision. Reverse engineering or disassembly is prohibited.

Main Features

Experience the high definition (HD) quality audio/video output and the library function of this Blu-ray Disc Player.

BD-ROM playback BD-ROM is a next generation optical disc format in the HD era. Featuring massive storage capacity of 25 to 50 GB (five times larger than a DVD) and a high-speed transfer rate of up to 54 Mbps, the format offers not only uncompromised HD quality video*1*2, but also enables rich bonus content on a single disc and HD quality audio up to 8ch, and interactive operability. *1 A compatible HD display device is necessary to enjoy the same

quality. *2 Some discs allow viewing only with an HDMI connection.

24p True Cinema Movies shot with a film camera consist of 24 frames per second. Since conventional televisions (both CRT and flat panels) display frames either at 1/60 or 1/50 second intervals, the 24 frames do not appear at an even pace. When connected to a TV with 24p capabilities, the player displays each frame at 1/24 second intervals the same interval originally shot with the film camera, thus faithfully reproducing the original cinema image.

HDMI Control (BRAVIA Theatre Sync) BRAVIA Theatre Sync Function makes operations simple by connecting Sony components that are compatible with the HDMI Control function with an HDMI cord.

BD-J application The BD-ROM format supports Java for interactive functions. BD-J offers content providers almost unlimited functionality when creating interactive BD-ROM titles*.

Java and all Java-based trademarks and logos are trademarks or registered trademarks of Sun Microsystems, Inc. in the U.S. and other countries. Esmertec and Jbed are trademarks or registered trademarks of Esmertec AG. 2000-2007 Esmertec AG

* This player does not support downloadable BD-J content.

Support of uncompressed multi-channel Linear PCM In combination with a compatible AV amplifier, the player can output up to 8ch Linear PCM surround sound*. With a non- compatible amplifier, the player can output 5.1ch analog signals from its 5.1CH OUTPUT jack for high quality audio enjoyment. * Note that the DIGITAL OUT (COAXIAL or OPTICAL) jack does not

output 8ch signals. You will need an HDMI cord and an HDMI- compatible device that support 8ch signals.

AVCHD format disc playback The player supports AVCHD format fileshigh definition recordings made on AVCHD-compatible camcorders. Your high definition personal archive is readily playable in HD quality.

ALL

AC IN

VIDEO OUT

COMPONENT VIDEO OUT

DIGITAL OUT PCM/DTS/DOLBY DIGITAL

5.1CH OUTPUT

VIDEO

Y

L

R

AUDIO OUT

L

R

WOOFER

COAXIAL OPTICAL

FRONT REAR CENTER

PB

PR

S VIDEO

HDMI OUT

1

1

,co

7

8

HDMI (High-Definition Multimedia Interface) digital interface When connected to an HDMI-equipped display device using a single HDMI cord, the player can output both SD to HD video and multi-channel audio signals, in digital form without degradation. The HDMI specification supports HDCP (High-bandwidth Digital Content Protection), a copy protection technology that incorporates coding technology for digital video signals.

Library function for recorded files (For JPEG image, MP3 audio, MPEG-2 PS movie files only) With DATA DVDs created on other DVD devices, three separate movie/music/photo Title List-browsers allow for easy sorting, searching and playback including a slideshow.

x.v.Color compatibility This player supports playback of video contents on discs recorded with x.v.Color technology. To watch this video content with the x.v.Color space, a TV or other display device supporting both video image reproduction using x.v.Color standard and capability of manual switching of its color space setting is required. Please consult your owners manual of your display device for further information.

About x.v.Color x.v.Color is a more familiar term for the xvYCC standard

proposed by Sony, and is a trademark of Sony Corporation. xvYCC is an international standard for color space in video.

This standard can express a wider color range than the currently used broadcast standard.

Getting Started

Getting Started Follow steps 1 to 7 to hook up and adjust the settings of the player. For jack and button names, see Index to Parts and Controls (page 58).

Notes Plug cords securely to prevent unwanted noise. Refer to the instructions supplied with the components to

be connected. You cannot connect this player to a TV that does not have

a video input jack. Be sure to disconnect the power cord of each component

before connecting. Do not apply too much pressure on the connecting cords.

Pushing against the cabinet wall, etc., may damage the cord.

Step 1: Unpacking

Check that you have the following items: Video cord (phono plug 1) (1) Stereo audio cord (phono plug 2) (1) HDMI cord (1)

(supplied with BDP-S301 only) Power cord (1) Remote commander (remote) (1) Size AA (R6) batteries (2)

Step 1: Unpacking . . . . . . . . . . . . . . . . . . . . . . .9

Step 2: Connecting the Video Cords/ HDMI Cord . . . . . . . . . . . . . . . . . . . . . . . . .10

Step 3: Connecting the Audio Cords . . . . . . . .12

Step 4: Connecting the Power Cord . . . . . . . . .16

Step 5: Preparing the Remote . . . . . . . . . . . . .16

Step 6: Easy Setup . . . . . . . . . . . . . . . . . . . . . .18

Step 7: Additional Adjustments . . . . . . . . . . . .19

9

10

Step 2: Connecting the Video Cords/HDMI Cord

Connect this player to your TV monitor, projector or AV amplifier (receiver) using a video cord. Select one of the patterns A through D, according to the input jack on your TV monitor, projector or AV amplifier (receiver). In order to view 1080p progressive signals with a compatible TV, projector, or monitor with an HDMI input jack, you must select pattern D. You can use pattern C to view 480p/720p progressive signals or 1080i interlace signals on a compatible device with component video input jacks.

A Connecting to a video input jack Connect the supplied video cord (yellow) to the yellow (video) jack. You will enjoy standard quality images.

When connecting to a standard 4:3 screen TV Depending on the disc, the image may not fit your TV screen. To change the aspect ratio, see page 45.

Note Do not connect a VCR, etc., between your TV and the player. If you pass the player signals via the VCR, you may not receive a clear image on the TV screen. If your TV has only one audio/video input jack, connect the player to this jack.

B Connecting to an S VIDEO input jack Connect using an S VIDEO cord (not supplied). You will enjoy high quality images.

C Connecting to component video input jacks (Y, PB, PR)

Connect the component via the COMPONENT VIDEO OUT jacks using a component video cord (not supplied) or three video cords (not supplied) of the same kind and length. You will enjoy accurate color reproduction and high quality images. You can also enjoy higher quality pictures from 480p/720p progressive signals or 1080i interlace signals, if your TV, projector or AV amplifier (receiver) is compatible.

AC IN

VIDEO OUT

COMPONENT VIDEO OUT

DIGITAL OUT PCM/DTS/DOLBY DIGITAL

5.1CH OUTPUT

VIDEO

Y

L

R

AUDIO OUT

L

R

WOOFER

COAXIAL OPTICAL

FRONT REAR CENTER

PB

PR

S VIDEO

HDMI OUT

AUDIO

INPUT

L

R

VIDEO

VIDEO OUT VIDEO

S VIDEO

Blu-ray Disc player

to VIDEO OUT

Video cord (supplied)

TV, projector, or AV amplifier (receiver): Signal flow

(yellow) (yellow)

VCR

Blu-ray Disc player TV Connect directly

AC IN

VIDEO OUT

COMPONENT VIDEO OUT

DIGITAL OUT PCM/DTS/DOLBY DIGITAL

5.1CH OUTPUT

VIDEO

Y

L

R

AUDIO OUT

L

R

WOOFER

COAXIAL OPTICAL

FRONT REAR CENTER

PB

PR

S VIDEO

HDMI OUT

INPUT

S VIDEO

VIDEO OUT VIDEO

S VIDEO

to S VIDEO

S VIDEO cord (not supplied)

TV, projector, or AV amplifier (receiver): Signal flow

Blu-ray Disc player

AC IN

VIDEO OUT

COMPONENT VIDEO OUT

DIGITAL OUT PCM/DTS/DOLBY DIGITAL

5.1CH OUTPUT

VIDEO

Y

L

R

AUDIO OUT

L

R

WOOFER

COAXIAL OPTICAL

FRONT REAR CENTER

PB

PR

S VIDEO

HDMI OUT

PR

PB

Y

COMPONENT VIDEO INCOMPONENT

VIDEO OUT

Y

PB

PR

to COMPONENT VIDEO OUT

(green)

(blue)

(red)

(green)

(blue)

(red)

Component video cord (not supplied)

TV, projector, or AV amplifier (receiver)

: Signal flow

Blu-ray Disc player

Getting Started

D Connecting to an HDMI input jack

Use an HDMI cord to enjoy high quality digital pictures and sound through the HDMI OUT jack. You will enjoy higher quality pictures from 480p/1080i, or 1080p (highest among the player output), if your TV, projector or AV amplifier (receiver) is compatible.

This Blu-ray Disc player incorporates High-Definition Multimedia Interface (HDMI) technology. HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC.

Notes on connecting to the HDMI OUT jack Observe the following as improper handling may damage the HDMI OUT jack and the connector. Carefully align the HDMI OUT jack on the back of the player

and the HDMI connector by checking their shapes. Make sure the connector is not upside down or tilted.

Be sure to disconnect the HDMI cord when moving the player.

If you place the player on the cabinet with the HDMI cord connected, do not apply too much pressure to the cabinet wall. It may damage the HDMI OUT jack or the HDMI cord.

When connecting or disconnecting, do not screw in or rotate the HDMI connector.

About indicators for HDMI connection After the player is turned on, the HD indicator on the front panel lights up when outputting 720p/1080i/1080p video signals. The HDMI indicator lights up when an HDMI device is connected.

Notes Consumers should note that not all high definition television sets are

fully compatible with this product and may cause artifacts to be displayed in the picture. In the case of 480/720/1080 progressive scan picture problems, it is recommended that the user switch the connection to the standard definition output. If there are questions regarding our TV set compatibility with this model 480p/720p/1080p Blu-ray Disc player, please contact our customer service center.

If the picture is not clear, natural, or to your satisfaction, change the video output resolution by pressing VIDEO FORMAT (page 46).

Be sure to use only an HDMI cord that bears the HDMI logo.

About the BRAVIA Theatre Sync features (for HDMI connections only)

By connecting Sony components that are compatible with the HDMI Control function with an HDMI cord, operation is simplified as below: One-Touch Play (page 21)

You can turn on the player and TV/AV receiver, set the TV/AV receivers input to the player, and start playback with one touch of the H button.

System Power-Off When you turn the TV off by using the POWER button on the TVs remote, the HDMI compatible components turn off automatically.

To prepare for the BRAVIA Theatre Sync features Set HDMI Control of Options setup to On (page 52).

Note Depending on the connected component, the HDMI Control function may not work. Refer to the operating instructions supplied with the component.

AC IN

VIDEO OUT

COMPONENT VIDEO OUT

DIGITAL OUT PCM/DTS/DOLBY DIGITAL

5.1CH OUTPUT

VIDEO

Y

L

R

AUDIO OUT

L

R

WOOFER

COAXIAL OPTICAL

FRONT REAR CENTER

PB

PR

S VIDEO

HDMI OUT

HDMI IN

HDMI OUT

HDMI cord (supplied with BDP-S301 only)

Blu-ray Disc player

to HDMI OUT

TV, projector, or AV amplifier (receiver)

HDMI

OUT

HDMI

OUT

11

12

Step 3: Connecting the Audio Cords

Select the connection that best suits your system. Be sure to read the instructions for the components you wish to connect.

*1 Manufactured under license from Dolby laboratories. Dolby, Pro Logic, and the double-D symbol are trademarks of Dolby Laboratories.

*2 DTS and DTS Digital Surround are registered trademarks of DTS, Inc.

Notes about the HDMI OUT jack When you connect the player to an AV amplifier (receiver)

using an HDMI cord, you will need to do one of the following: Connect the AV amplifier (receiver) to a TV with the HDMI

cord. Connect the player to the TV with a video cord other than an

HDMI cord (component video cord, S VIDEO cord, or video cord).

When connecting to the HDMI OUT jack, carefully align the HDMI connector with the jack. Do not bend or apply pressure to the HDMI cord.

If you change the component connected to the HDMI OUT jack, change Audio (HDMI) in Audio Setup to match the new component (page 47). The player stores the HDMI related settings for up to five components.

The HDMI connection is compatible with 2ch Linear PCM signals (48 to 192 kHz, 16/20/24 bit), and 6 to 8ch Linear PCM signals (48 to 96 kHz, 16/20/24 bit), in addition to Dolby Digital and DTS bit stream (5.1ch signals up to 96 kHz, 16/20/ 24bit).

Note If you connect a component that does not conform to the selected audio signal, a loud noise (or no sound) will come out from the speakers, which could damage your ears or speakers.

Connection Your setup

TV

Stereo amplifier (receiver) and two speakers

AV amplifier (receiver) having a Dolby*1 Surround (Pro Logic) decoder and 3 to 6 speakers Surround effects: Dolby Surround

(Pro Logic)

AV amplifier (receiver) with 5.1ch input jacks and 6 speakers Surround effects: Dolby Digital

(5.1ch), DTS (5.1ch)

AV amplifier (receiver) with a digital input jack having a Dolby Digital or DTS*2 decoder and 6 speakers Surround effects: Dolby Digital

(5.1ch), DTS (5.1ch)

AV amplifier (receiver) with an HDMI input jack and 8 speakers Surround effects: 8ch Linear

PCM

A

B

C

D-1

D-2

D-3

Getting Started

ntinued

Connecting to your TV This connection will use your TVs speakers for sound.

Connecting to a stereo amplifier (receiver) and 2 speakers

If your stereo amplifier (receiver) only has audio input jacks L and R, use . If your amplifier (receiver) has a digital input jack, use .

AC IN

VIDEO OUT

COMPONENT VIDEO OUT

DIGITAL OUT PCM/DTS/DOLBY DIGITAL

5.1CH OUTPUT

VIDEO

Y

L

R

AUDIO OUT

L

R

WOOFER

COAXIAL OPTICAL

FRONT REAR CENTER

PB

PR

S VIDEO

HDMI OUT

AUDIO

INPUT

L

R

VIDEO

AUDIO OUT

L

R

to AUDIO OUT L/R

TV

(white)

(red)

(white)

(red)

Stereo audio cord (supplied)

: Signal flow

Blu-ray Disc player

A

AC IN

VIDEO OUT

COMPONENT VIDEO OUT

DIGITAL OUT PCM/DTS/DOLBY DIGITAL

5.1CH OUTPUT

VIDEO

Y

L

R

AUDIO OUT

L

R

WOOFER

COAXIAL OPTICAL

FRONT REAR CENTER

PB

PR

S VIDEO

HDMI OUT

B-2 B-1 DIGITAL OUT

PCM/DTS/DOLBY DIGITAL COAXIAL OPTICAL

AUDIO OUT

L

R

Optical digital cord (not supplied)

to DIGITAL OUT (COAXIAL or OPTICAL)

or

(red)(white)

Stereo audio cord (supplied)

to audio input

Stereo amplifier (receiver)[Speakers]

Front (L)

Front (R)

to coaxial or optical digital input

Coaxial digital cord (not supplied)

: Signal flow

Blu-ray Disc player

to AUDIO OUT L/R

(white) (red)

B

B-1

B-2

,co

13

14

Connecting to an AV amplifier (receiver) having a Dolby Surround (Pro Logic) decoder and 3 to 6 speakers

If your AV amplifier (receiver) only has L and R audio input jacks, use . If your amplifier (receiver) has a digital input jack, use . You can enjoy surround effects only when playing Dolby Surround audio or multi-channel audio (Dolby Digital or DTS) discs.

Connecting to an AV amplifier (receiver) with 5.1ch input jacks and 6 speakers

If your AV amplifier (receiver) has 5.1 channel inputs, use .

AC IN

VIDEO OUT

COMPONENT VIDEO OUT

DIGITAL OUT PCM/DTS/DOLBY DIGITAL

5.1CH OUTPUT

VIDEO

Y

L

R

AUDIO OUT

L

R

WOOFER

COAXIAL OPTICAL

FRONT REAR CENTER

PB

PR

S VIDEO

HDMI OUT

DIGITAL OUT PCM/DTS/DOLBY DIGITAL COAXIAL OPTICAL

C-2 C-1 AUDIO OUT

L

R

Coaxial digital cord (not supplied)

to DIGITAL OUT (COAXIAL or OPTICAL)

or

to AUDIO OUT L/R

(red)(white)

Stereo audio cord (supplied)

(red)(white)

to audio input to coaxial or optical digital input

Optical digital cord (not supplied)

[Speakers] [Speakers]

Rear (L) Rear (R)

Subwoofer

Center

Rear (mono)

Front (L)

Front (R)

AV Amplifier (receiver) with a decoder

: Signal flow

Blu-ray Disc player

z Hint For correct speaker location, see the operating instructions of the connected components.

Note When connecting 6 speakers, you do not need the Rear (mono) speaker above.

C

C-1

C-2

AC IN

VIDEO OUT

COMPONENT VIDEO OUT

DIGITAL OUT PCM/DTS/DOLBY DIGITAL

5.1CH OUTPUT

VIDEO

Y

L

R

AUDIO OUT

L

R

WOOFER

COAXIAL OPTICAL

FRONT REAR CENTER

PB

PR

S VIDEO

HDMI OUT

5.1CH OUTPUT

L

R

WOOFER

FRONT REAR CENTER

D-1

[Speakers] [Speakers]

Rear (L)

Rear (R)

Subwoofer Front (L)

Front (R)

Center

AV amplifier (receiver) with 5.1ch inputs

: Signal flow

to 5.1CH OUTPUT

Blu-ray Disc player

to audio input

Stereo audio cord (one is supplied)

Monaural audio cord (not supplied)

z Hint For correct speaker location, see the operating instructions of the connected components.

D-1

D-1

Getting Started

Connecting to an AV amplifier

(receiver) with a digital input jack and 6 speakers

If you want to use the Dolby Digital, or DTS decoder function on your AV amplifier (receiver), connect to its digital jack using

. You can enjoy a more realistic audio presence.

Connecting to an AV amplifier (receiver) with an HDMI input jack and 8 speakers

If your AV amplifier (receiver) accepts 8ch Linear PCM input with an HDMI connection, you can enjoy the surround sound using .

AC IN

VIDEO OUT

COMPONENT VIDEO OUT

DIGITAL OUT PCM/DTS/DOLBY DIGITAL

5.1CH OUTPUT

VIDEO

Y

L

R

AUDIO OUT

L

R

WOOFER

COAXIAL OPTICAL

FRONT REAR CENTER

PB

PR

S VIDEO

HDMI OUT

D-2 DIGITAL OUT

PCM/DTS/DOLBY DIGITAL COAXIAL OPTICAL

HDMI OUT

to DIGITAL OUT (COAXIAL or OPTICAL)

Coaxial digital cord (not supplied)

Optical digital cord (not supplied)

to coaxial or optical digital input

[Speakers] [Speakers]

Rear (L)

Rear (R)

Subwoofer Front (L)

Front (R)

Center

AV amplifier (receiver) having a decoder

: Signal flow

to HDMI OUT

HDMI cord (supplied with BDP-S301 only)

or

to HDMI input

Blu-ray Disc player

or

z Hint For correct speaker location, see the operating instructions of the connected components.

D-2

D-2

AC IN

VIDEO OUT

COMPONENT VIDEO OUT

DIGITAL OUT PCM/DTS/DOLBY DIGITAL

5.1CH OUTPUT

VIDEO

Y

L

R

AUDIO OUT

L

R

WOOFER

COAXIAL OPTICAL

FRONT REAR CENTER

PB

PR

S VIDEO

HDMI OUT

D-3

HDMI OUT

[Speakers] [Speakers]

Rear1 (L)

Rear1 (R)

Rear2 (L) Front (L)

Front (R)

Center

AV amplifier (receiver) with 8ch outputs

to HDMI OUT

HDMI cord (supplied with BDP-S301 only)

to HDMI input

Blu-ray Disc player

z Hint For correct speaker location, see the operating instructions of the connected components.

Note Not all HDMI-compatible AV amplifiers (receivers) accept 8ch Linear PCM signals. See also the operating instructions supplied with the connected AV amplifier (receiver).

Rear2 (R)

Subwoofer

D-3

D-3

15

16

Step 4: Connecting the Power Cord

After all of the other connections are complete, connect the supplied power cord to the AC IN terminal of the player. Then plug the player and TV power cords into the AC outlet.

Step 5: Preparing the Remote

You can control the player using the supplied remote. Insert two Size AA (R6) batteries by matching the 3 and # ends on the batteries to the markings inside the battery compartment. When using the remote, point it at the remote sensor on the player (page 58).

AC IN

to AC outlet

to AC IN

Notes Do not leave the remote in an extremely hot or humid place. Do not drop any foreign object into the remote casing, particularly

when replacing the batteries. Do not expose the remote sensor to direct sunlight or a lighting

apparatus. Doing so may cause a malfunction. If you do not use the remote for an extended period of time, remove the

batteries to avoid possible damage from battery leakage and corrosion.

Getting Started

If you want to control your TV with the supplied remote

You can control the volume, input source, and power switch of your Sony TV with the supplied remote.

To control other TVs with the remote You can control the volume, input source, and power switch of non- Sony TVs as well. If your TV is listed in the table below, set the appropriate manufacturers code.

1 While holding down TV [/1, press the number buttons to select your TV manufacturers code (see the table below).

2 Release TV [/1.

Code numbers of controllable TVs If more than one code number is listed, try entering them one at a time until you find the one that works with your TV.

To return the remote to its default settings

1 Remove the batteries from the remote.

2 Re-insert the batteries while pressing down 1, 2, and 3 of the number buttons.

3 Wait for a few seconds.

Note Depending on the connected unit, you may not be able to control your TV using all or some of the buttons on the supplied remote.

By pressing You can

TV [/1 Turn the TV on or off.

VOL +/ Adjust the volume of the TV.

TV/VIDEO Switch the TVs input source between the TV and other input sources.

CH +/ Select the channel up and down.

MUTING Mute the sound (for Sony TV only).

DISPLAY

OPEN/ CLOSE

DIMMER

CLEAR

1 2 3

4 5 6

7 8

0

9

TV/VIDEO

AUDIO SUBTITLE ANGLE

SCAN

MUTING

PLAY MODE

PLAY SCAN

PREV SLOW/STEP NEXT

PAUSE

VOL CH

STOP

VIDEO FORMAT

RED GREEN BLUE YELLOW

TOP MENU

SYSTEM MENU

POP UP/ MENURETURN

TV

Number buttons

MUTING

TV \/1 TV/VIDEO

CH +/

VOL +/

Manufacturer Code number

Sony 01 (default)

Daewoo 22, 04

Emerson 14

GE 06

Hitachi 02, 04

JVC 09

LG/Gold star 03, 17, 04

MGA/Mitsubishi 13, 04

NEC 04, 12

Panasonic 19

Philips 08, 21

Pioneer 16

RCA 10, 04

R.Shack 05

Samsung 04, 12, 20

Sanyo 11

Sharp 05, 18

Toshiba 07, 18

Zenith 15

17

18

Step 6: Easy Setup

Follow the steps below to make the minimum number of basic adjustments for using the player. If you do not complete Easy Setup, it will appear each time you turn on your player. Make the settings below in the following order.

a Turn on the TV.

b Press [/1 to turn on the player. The player turns on after a moment.

c Switch the input selector on your TV so that the signal from the player appears on your TV screen. If the display for OSD language selection does not appear, select Start of Easy Setup in Options Setup (page 52).

d Select the OSD language you want to display, and press ENTER.

This will determine the Audio, Subtitle and BD/ DVD menu languages as well.

e Select Start, and press ENTER to start Easy Setup.

If the above display does not appear Go to step 6. This display appears only when the player is turned on for the first time.

f Select the video output format for the connected TV, and press ENTER. For details about the video output, see page 46.

When using the HDMI OUT jack

Select from Auto, 480i, 480p, 720p, 1080i, 1080p, or Source Direct, then go to step 8. TV Type in step 7 will be set to 16:9 (wide screen).

When using the jacks other than the HDMI OUT jack

Select from S-Video/Video only, 480i, 480p, 720p, 1080i or Dont Know. If you select 720p or 1080i, go to step 8. TV Type in step 7 will be set to 16:9 (wide screen).

When turned on for the first time Wait about 90 seconds before the player turns on and starts Easy Setup. The start-up time will be much shorter once Easy Setup is completed.

OPEN/ CLOSE

DIMMER

CLEAR

1 2 3

4 5 6

7 8

0

9

DISPLAY TV/VIDEO

AUDIO SUBTITLE ANGLE

PREV SLOW/STEP NEXT

VIDEO FORMAT

RED GREEN BLUE YELLOW

TOP MENU

SYSTEM MENU

POP UP/ MENURETURN

TV

"/1

Confirm ExitSYSTEM MENU

Select the on-screen display language. Audio, subtitle and BD/DVD menu language options will be set to the same language as this.

Language

Easy Setup

English

Franais

Confirm ExitSYSTEM MENU

Use to select then press ENTER.

Before using, make some simple settings for the BD player.

Please use the Initial Setup if you want to make more detailed settings.

Easy Setup

Start

Cancel

Confirm ExitSYSTEM MENU

Select [Auto] to automatically match the video output format with the HDMI-connected TV.

Output Video Format

Easy Setup

Auto

480i

480p

720p

1080i

1080p

Source Direct

Confirm ExitSYSTEM MENU

Select [Auto] to automatically match the video output format with the HDMI-connected TV.

Output Video Format

Easy Setup

S-Video/Video only

480i

480p

720p

1080i

Don't Know

Getting Started

g Select the aspect ratio that matches your TV, and press ENTER.

If you have a wide screen TV or a 4:3 standard TV with a wide screen mode Select 16:9 (page 45).

If you have a 4:3 standard TV Select 4:3 (page 45).

h Select Finish Setup, and press ENTER.

z Hints If you want to reset these settings to their factory defaults, see

Resetting the Player (page 53). You can re-run Easy Setup from Options Setup (page 52).

Step 7: Additional Adjustments

The following settings and adjustments are necessary when your connection applies.

For video connection When using the COMPONENT VIDEO OUT jacks

(Pattern C page 10) Select the video output resolution for your TV by pressing

VIDEO FORMAT (page 46).

When using the HDMI OUT jack (Pattern D page 11)

Select the video output resolution for your TV by pressing VIDEO FORMAT (page 46).

Select the type of video output from the HDMI OUT jack in YCbCr/RGBPC (HDMI) of Video Setup (page 45).

For audio connection When using the DIGITAL OUT (OPTICAL or COAXIAL) jack

(Connection , , page 13 to 15) Set Dolby Digital and DTS in Audio Setup (page 47)

according to your AV amplifiers (receivers) decoder.

When using the HDMI OUT jack (HDMI connection of , page 15)

Set Dolby Digital and DTS in Audio Setup (page 47) according to your AV amplifiers (receivers) decoder.

Select the audio output method from the HDMI OUT jack in Audio (HDMI) of Audio Setup (page 47).

When using the AUDIO OUT (L/R) jacks (Connection page 14)

Set DTS Downmix to Lt/Rt in Audio Setup (page 47).

When using the 5.1CH OUTPUT jacks (Connection page 14)

Set Audio Output Mode to 5.1 Channel in Speakers Setup (page 51), and adjust the Speaker Setup setting for your system.

Notes If you connect a component that does not conform to the selected audio

signal, a loud noise (or no sound) will come out from the speakers, which could damage your ears or speakers.

If you connect using the HDMI OUT jack or COMPONENT VIDEO OUT jacks and the picture does not appear clearly, the connected display device may not be compatible with the progressive signals. In this case, connect the display device to the S VIDEO jack or the VIDEO jack (pattern A or B see page 10), re-run the Easy Setup from the Options Setup (page 52), and select S-Video/Video only in step 6 (page 18). Also, check the above items again to see if any additional adjustment is required.

Confirm ExitSYSTEM MENU

Select the screen aspect ratio to match your TV.

TV Type

Easy Setup

16:9

4:3

Confirm ExitSYSTEM MENU

Use to select then press ENTER.

Setup is complete! Enjoy using your BD player!

Easy Setup

Finish Setup

Go Back

B-2 C-2 D-2

D-2 D-3

C-1

D-1

19

20

Basic Operations

Most of the BD playback operations are common to DVD. This section covers BD/ DVD/CD playback in general, together with the basic operation of the player. For browsing recorded files on DATA DVDs*, a separate library function is available. See also page 32 for movie, 36 for music, 40 for photo files. For operations using the remote, a complete list is located on page 24.

* DVD+RWs/DVD+Rs/DVD-RWs/DVD-Rs containing MPEG-2 PS movie, MP3 audio, or JPEG image files.

Playing a Disc

a Press \/1. The player turns on after a moment.

b Switch the input selector on your TV so that the signal from the player appears on your TV screen.

c Press Z to open the disc tray.

d Place a disc on the disc tray with the playback side facing down.

BD DVD CD

OPEN/ CLOSE

DIMMER

CLEAR

DISPLAY TV/VIDEO

AUDIO SUBTITLE ANGLE

SCAN

MUTING

PLAY MODE

PLAY SCAN

PREV SLOW/STEP NEXT

PAUSE

VOL CH

STOP

VIDEO FORMAT

RED GREEN BLUE YELLOW

TOP MENU

SYSTEM MENU

POP UP/ MENURETURN

TV

1 2 3

4 5 6

7 8

0

9

xX

TOP MENU

POP UP/MENU

Number buttons

Color buttons

Z \/1

SYSTEM MENU

RETURN

H

Playback side facing down

Playing a Disc. . . . . . . . . . . . . . . . . . . . . . . . . 20

Guide to Displays . . . . . . . . . . . . . . . . . . . . . . 22

Guide to the Remote. . . . . . . . . . . . . . . . . . . . 24

Checking the Disc Information . . . . . . . . . . . . 26

Clarifying Low Volume Sounds (Audio DRC) . 27

Adjusting the Pictures . . . . . . . . . . . . . . . . . . 28

Locking a Disc . . . . . . . . . . . . . . . . . . . . . . . . 29

Basic Operations

e Press Z to close the disc tray. Wait a short while until the disc type appears on the front panel display.

f Press H to start playback. For more information about the remotes operations, see page 24.

g When you finish playing, press Z to open the disc tray.

h Remove the disc, and press Z again to close the disc tray.

i Press \/1 to turn off the player.

To use the BDs or DVDs menu When you play a BD-ROM, DVD VIDEO, or a finalized DVD+RW, DVD-RW (Video mode), DVD+R, or DVD-R (Video mode), you can display the discs menu by pressing TOP MENU or POP UP/MENU. Some BDs/DVDs display the menu automatically. Either cases, navigate through the menu using

To play restricted BDs If CANT PLAY appears on the front panel display for a BD- ROM, change the BD Parental Control setting (page 30).

To play restricted DVDs For a restricted DVD, the display asks for the password. For DVD Parental Control setting, see page 30.

1 Enter your four-digit password using the number buttons.

2 Press ENTER to confirm. To register or change the password, see page 29.

Notes about Resume Play Playback starts from the beginning if the title has not been

played or the previous stop point is canceled. The stop point is canceled when:

you change the settings on the player. you turn off the player (BD-ROM and DATA DVD only). you press x twice. you open the disc tray. you finish a search.

The player remembers the stop point for one title/track/file only. On a music CD, playback resumes from the beginning of the track.

Depending on the disc, the Resume function may not work.

About the screen saver function To prevent damage to your display device (ghosting), a screen saver image appears when the player is left unattended, has no disc inserted, or no title/slideshow is displayed for 15 minutes. To cancel, press any button on the remote or the player.

About One-Touch Play (for HDMI connections only) With one touch of the H button, the player and your TV/AV receiver automatically turn on and the TV/AV receivers input is switched to the player. Playback starts automatically. To use this function, set HDMI Control of Options setup to On (page 52). The TV/AV receivers input will also switch to the player automatically, in the following cases: You press H, SYSTEM MENU, TOP MENU, or POP UP/

MENU buttons on the remote. A disc with auto playback function is loaded.

Buttons Details

X Pauses playback, or restarts playback from the same point.

x Stops playback, or cancels the resume point when pressed twice.

H Starts or restarts playback from the previous stop point.

21

22

Guide to Displays

When Select an item, and press ENTER appears in this manual, press the

a Press SYSTEM MENU to turn on the above System Menu. The players start menu appears, with entries to all of the functions.

b Select an item, and press ENTER. Each item leads to the following function displays. See the pages in parentheses for operations. When you want to return to the previous display, press RETURN.

Title List For DATA DVDs, this display leads further to the Title Lists of content type. The three Title Lists appear similar and are operable in a similar way.

Select the Title List you want to view; from Movies, Photos, or Music, and press ENTER.

Movies Displays movies/video titles only (page 32).

Photos Displays image files only (page 40).

Music Displays music files only (page 36).

A/V Control (page 27) Adjusts the audio/video settings. Select either Video Control, or Audio Control, and press ENTER.

Setup (page 44) Enters the Setup displays for changing the players settings. Select the related Setup display, and press ENTER.

BD DVD DATA DVD CD

Select ExitSYSTEM MENU

Search for the part you want to play from a list of the disc's content.

System Menu

Title List

A/V Control

Setup

Select ExitSYSTEM MENU

Access the BD-R/RE titles.

Title List

Movies

Photos

Music

Select ExitSYSTEM MENU

Set the playback picture quality.

A/V Control

Video Control

Audio Control

Use to select an item, then press [RR] or ENTER.

Confirm ExitSYSTEM MENU

Setup

Video Setup

Audio Setup

Language

Parental Control

Speakers

Options

TV Type

4:3 Video Output

DVD Aspect Ratio

YCbCr/RGBPC(HDMI)

24p Output

16:9

Normal

Letter Box

Y, Cb, Cr

Off

Basic Operations

Entering characters

When an on-screen keyboard appears (e.g., when searching for a title), enter the characters as follows.

a Select the character you want to enter, and press ENTER. The character appears in the entry field. If necessary, select the following items, and press ENTER.

b Repeat step 1 to complete the entry.

c Select DONE, and press ENTER to close the on-screen keyboard.

Note You cannot use the extended character set.

Items Details

SHFT Switches between upper and lower case characters. Select this before entering the character.

SPC Inserts a space.

DEL Deletes the last character input.

CLR Clears all input characters.

DATA DVD

A B

SHFT

DONE CANCEL SPC DEL CLR

C D E F G H I J K L M N O P Q R S T U V W X Y Z , . : ; 1 2 3 4 5 6 7 8 9 0 _ ( )

s_

23

24

Guide to the Remote

The following covers all of the remotes functions. Refer to the list when necessary.

Number 5, AUDIO, CH+, and H buttons have a tactile dot. Use the tactile dot as a reference when operating the player.

OPEN/ CLOSE

DIMMER

CLEAR

1 2 3

4 5 6

7 8

0

9

DISPLAY TV/VIDEO

AUDIO SUBTITLE ANGLE

SCAN

MUTING

PLAY MODE

PLAY SCAN

PREV SLOW/STEP NEXT

PAUSE

VOL CH

STOP

VIDEO FORMAT

RED GREEN BLUE YELLOW

TOP MENU

SYSTEM MENU

POP UP/ MENURETURN

TV

A Z OPEN/CLOSE (page 20) Opens/closes the disc tray.

TV &/1 (page 17) Turns the TV on or to standby mode.

&/1 (page 18) Turns on, or sets the player to standby mode.

B DIMMER (page 59) Changes the brightness of the front panel display

on the player (when completely darkened, indicators on the front panel are also turned off and the FL OFF indicator lights up).

DISPLAY (page 26) Displays the disc information on the screen.

TV/VIDEO (page 17) Switches between TV and other input sources.

C Number buttons (page 26) Enters the title/chapter numbers, etc.

CLEAR Clears the entry field.

D VIDEO FORMAT (page 45) Changes the video output resolution from the

HDMI OUT jack and the COMPONENT VIDEO OUT jacks. Press this button repeatedly if no picture appears.

E AUDIO*1 (page 49) Selects the sound track or the language track on a

BD/DVD. *1 When playing MPEG-2 movie files or MP3 music files on a

DATA DVD, or a music CD, you cannot select the left or right channel only.

SUBTITLE (page 49) Selects the subtitle language on a BD/DVD.

ANGLE Switches to other viewing angles when available.

F Color buttons (RED/GREEN/BLUE/YELLOW) Short cut keys for selecting items on some BDs

menus (can also be used for BDs Java interactive operations).

Basic Operations

ntinued

Playing in various play mode

a During playback, press PLAY MODE repeatedly. Available items differ depending on the current title/ track/file or the disc type. To cancel the Play Mode, press PLAY MODE again. For Time Search, see Searching using the remote (page 26).

When playing a video or movie title

When playing a music track

When playing a photo image

G SYSTEM MENU (page 22) Enters/exits the players start menu (System

Menu).

TOP MENU (page 20) Opens/closes the BDs or DVDs top menu.

POP UP/MENU (page 20) Opens/closes the BDs pop up menu, or the

DVDs disc menu.

RETURN (page 20, 22) Returns to the previous display.

</M/m/, (page 20, 22) Moves the highlight to select a displayed item.

Center button (ENTER) (page 20, 22) Enters the selected item.

H ./> PREV/NEXT Skips to the previous/next chapter, track, or file.

c/ C SLOW/STEP*2

Plays in slow motion or stop motion. To return to normal play, press H.

To play in slow motion Press C during playback. When slow motion play starts, press C repeatedly to change the speed : 1/16 t 1/8 t 1/4 t 1/2 of normal playback speed.

To play in stop motion (step by step) Press X during playback, then press c or C repeatedly.

m/M SCAN*2

Scans backwards or forward. The speed changes when pressed repeatedly.

*2 Depending on the disc or file type, the function may not work or the scan speeds may differ.

H PLAY Starts or re-starts playback.

PLAY MODE Switches to other play modes (Repeat Play, etc.)

when pressed during playback. Searches for a specific point (page 26).

X PAUSE Pauses/re-starts playback.

x STOP Stops playback. Clears the resume point when pressed twice. The

resume point for a title is the last point you played, the last track for an audio file, or the last photo for a photo file.

I For TVs operable with the following buttons, see page 17.

MUTING (page 17) Mutes the TV sound.

VOL (volume) +/ (page 17) Adjusts the TV volume.

CH (channel) +/ (page 17) Selects the TV channels up and down.

Items Details

Repeat Chapter (BD-ROM/DVD VIDEO only)

Repeats the current chapter.

Repeat Title Repeats the current title.

Items Details

Repeat Track Repeats the current track.

Repeat All Repeats all the tracks on the disc or the Music Title List.

Random Plays all the tracks on the disc or the Music Title List in a random order.

Items Details

Repeat All Repeats all the files on the disc or Photos Title List.

Random Plays all the files on the disc or Photos Title List in a random order.

BD DVD DATA DVD CD

,co

25

26

Searching using the remote

You can search by entering the title/chapter number or the time code (elapsed time from the beginning of the disc).

To search for a title or chapter (BD-ROM, DVD VIDEO only) 1 Enter the title number using the number buttons

while the player is in stop mode. To search for a chapter, enter the chapter number during playback. If you make a mistake, press CLEAR once and re-enter.

2 Press ENTER to start playback.

To search for a specific point 1 During playback, press PLAY MODE repeatedly

until Time Search appears.

2 Enter the time code using the number buttons. Enter the time in minutes and seconds (e.g., 12030 for 1 hour, 20 minutes and 30 seconds). If you make a mistake, press CLEAR once and re-enter.

3 Press ENTER to start playback.

Note Depending on the DVD VIDEO/BD-ROM/DATA DVD, these search functions may not work.

Checking the Disc Information

You can check the title/chapter/track information including video transmission rate etc., by pressing DISPLAY. The information differs depending on the disc type and the player status.

a Press DISPLAY.

Example: When playing a DVD VIDEO.

The following information appears:

1 Playback status

2Disc type

3 Title information Currently playing title number/currently playing

chapter number. Total number of chapters within the title. Total playback time of the title.

4 Elapsed time of the current title

5 Play mode

b Press DISPLAY again.

The display switches to show the following information:

1Chapter information Elapsed time of the current chapter. Total playback time of the current chapter.

2Video transmission rate and the stream information

BD DVD DATA DVD

DISPLAY

OPEN/ CLOSE

DIMMER

CLEAR

1 2 3

4 5 6

7 8

0

9

TV/VIDEO

AUDIO SUBTITLE ANGLE

SCAN

MUTING

PLAY MODE

PLAY SCAN

PREV SLOW/STEP NEXT

PAUSE

VOL CH

STOP

VIDEO FORMAT

RED GREEN BLUE YELLOW

TOP MENU

SYSTEM MENU

POP UP/ MENURETURN

TV

Number buttons

ENTER

PLAY MODE

BD DVD DATA DVD CD

1-1 2.01.23 Chapters 12 Title Total 2h15m34s

Play DVD-VIDEO

Repeat Title

1-1 2.01.23 Chapter Time 01.11.56 Chapter Total 2h15m34s 10.03 Mbps

Play DVD-VIDEO

Repeat Title

Basic Operations

z Hints You can check disc information also on the front panel display

(page 59) or the Title List display (page 22). You can check the audio information by pressing AUDIO.

Clarifying Low Volume Sounds (Audio DRC)

Even at low volume, you can make low sounds such as dialogs more audible.

a Press SYSTEM MENU during playback.

b Select A/V Control, and press ENTER.

c Select Audio Control, and press ENTER to turn on the above display.

d While Audio DRC is highlighted, select from Max to Off by pressing </,.

e Press ENTER.

Note Audio DRC is effective only when the disc is a Dolby Digital Blu-ray Disc or DVD, and: Dolby Digital in Audio Setup is set to Downmix PCM (page 47)

and the audio signals are output from the DIGITAL OUT (OPTICAL or COAXIAL) jack or the HDMI OUT jack.

Audio (HDMI) in Audio Setup is set to PCM (page 47) and the audio signals are output from the HDMI OUT jack.

the audio signals are output from the AUDIO OUT (L/R) jacks or the 5.1CH OUTPUT jacks.

BD DVD DATA DVD

Adjusting sound accentual width (dynamic range). This is effective when playback sound is Dolby Digital.

Audio Control Off MaxAudio DRC

Convenient when you cannot turn up the volume (e.g., at night)

27

28

Adjusting the Pictures

The cinema tuned picture preset setting will allow you to maximize the visual impact of the BD or DVD you are watching by optimizing the picture settings for different lighting environments. Memory allows you to make your own detailed adjustments.

a Press SYSTEM MENU during playback.

b Select A/V Control, and press ENTER.

c Select Video Control, and press ENTER to turn on the above display.

d Press </, to select a setting.

e Press ENTER.

z Hint The above description applies when the picture setting of your TV (if any) is set to Standard.

Fine-tuning the picture to your preference

a Select from Memory 1 to Memory 3 in step 4 of Adjusting the Pictures (page 28).

b Select Detailed Settings, and press ENTER to turn on the above display. To switch to another Memory, press RETURN.

c Select each of the picture elements, and adjust using </,. To adjust while previewing the effect

Select a setting and press ENTER to switch the display for the setting. Press

Underlined are the default settings for Memory.

d Press RETURN.

Items Details

Brighter Room For a room brighter than normal.

Theater Room For a dark room such as a home theater.

Standard (default) Normally, select this.

Memory (1-3) Select a setting when you want to use the detailed picture adjustments you previously made, or when you want to make a new set. The player remembers up to three sets (see page 28).

BD DVD DATA DVD

Standard

Detailed Settings

Items Details

White Adjust (Min~(mid)~Max)

Adjusts the brightness of white colors.

Black Adjust (Min~(mid)~Max)

Adjusts the richness of dark colors.

Hue (Green~(mid)~Red)

Balances the green and the red colors.

Color Level (Min~(mid)~Max)

Adjusts the color saturation.

Use [LL][RR] to set the behavior of film source input. Press ENTER to preview.

Min Max

Memory1

Green Red

Min Max

White Adjust

Black Adjust

Hue

Color Level

Min Max

Basic Operations

ntinued

Locking a Disc

By setting the password and your limit in Parental Control Setup, you can control playback of inappropriate discs.

Notes You cannot limit playback if the DVD VIDEO/BD-ROM does not

have the Parental Control function. If you forget the password, you will have to return all of the player

settings to their factory defaults (page 53). The above display does not appear for BD-ROM. If you cannot play a

BD-ROM because of Parental Control, reset Change Age Restriction of BD Parental Control (page 50).

Setting/changing the password

a Press SYSTEM MENU.

b Select Setup, and press ENTER.

c Select Parental Control, and press ENTER to turn on the above Parental Control Setup.

d Select Change Password (Set Password), and press ENTER.

e Select Next Screen, and press ENTER to turn on the password display. When you have not yet registered a password

Enter a four-digit password using the number buttons, and press m. Re-enter it for confirmation, and press ENTER.

When you have already registered a password Enter the four-digit password using the number buttons, and press ENTER. Enter a new password and press m, then re-enter it for confirmation, and press ENTER.

z Hint To continue to set DVD Parental Control, go to step 4 of Setting the Parental Control for DVD VIDEOs (page 30).

BD DVD

Parental Control BD PLAYER

Current Level Disc Level

3 5

Use the number keys to enter the password to turn off the parental lock.

The password is required when the DVD exceeds the level you set.

BD DVD

Use to select an item, then press [RR] or ENTER.

Confirm ExitSYSTEM MENU

Setup

Video Setup

Audio Setup

Language

Parental Control

Speakers

Options

Change Password

DVD Parental Control

BD Parental Control

Next Screen

Next Screen

Next Screen

,co

29

30

Setting the Parental Control for DVD VIDEOs

a Press SYSTEM MENU.

b Select Setup, and press ENTER.

c Select Parental Control, and press ENTER to turn on the Parental Control Setup.

d Select DVD Parental Control, and press ENTER.

e Select Change Level, and press ENTER to turn on the above display. This will set the playback limitation level.

f Enter the password using the number buttons, and press ENTER.

g Press </, to select the limitation level from Off to Level 8, and press ENTER. Note that the lower the value, the stricter the limitation.

h When the display returns to the Parental Control Setup, select DVD Parental Control, and press ENTER.

i Select DVD Country Code, and press ENTER. This ensures that you see the scenes intended for your residential area.

j On the DVD Country Code display, enter the password using the number buttons, and press ENTER.

k Press </, to select your country code (see page 69), or press m and enter the code for your area using the number buttons.

l Press ENTER.

z Hint To continue to set BD Parental Control, go to step 4 of Setting the Parental Control for BD-ROMs (page 30).

Setting the Parental Control for BD- ROMs

a Press SYSTEM MENU.

b Select Setup, and press ENTER.

c Select Parental Control, and press ENTER to turn on the Parental Control Setup.

d Select BD Parental Control, and press ENTER.

e Select Change Age Restriction, and press ENTER to turn on the above display. For BD-ROMs, the restriction is set by age, not by level.

f Enter the password using the number buttons, and press ENTER.

g Press </, to select the age from 0 to 255, and press ENTER.

h When the display returns to the Parental Control Setup, select BD Parental Control, and press ENTER.

i Select BD Country Code, and press ENTER. This ensures that you see the scenes intended for your residential area.

j On the BD Country Code display, enter the password using the number buttons, and press ENTER.

k Press </, to select your country code (see page 69), or press m and enter the code for your area using the number buttons.

l Press ENTER.

DVD

Use the number keys to enter the password, and press ENTER.

Confirm ExitSYSTEM MENU

Change Level

Password

Level

Setup

Video Setup

Audio Setup

Language

Parental Control

Speakers

Options Off

BD

Use the number keys to enter the password, and press ENTER.

Confirm ExitSYSTEM MENU

Password

Age Restriction

Video Setup

Audio Setup

Language

Parental Control

Speakers

Options

Change Age Restriction

Setup

255

Basic Operations

31

32

Watching Movie Files

Use the Movies Title List to browse through and sort MPEG-2 PS movie files on DATA DVDs.

Viewing All Titles

The Movies Title List first displays all titles on the disc.

a Press SYSTEM MENU.

b Select Title List, and press ENTER.

c Select Movies, and press ENTER. The above All Movies display appears, showing all titles (scrollable by pressing m). From All Movies you can apply items to all titles using the Browse menu (see below).

To use the Browse menu Press < after step 3 to display the items for the Movies Title List. For operations, see the pages in parentheses. Available items differ depending on the display.

Example: To apply Sort to all titles

A Select Sort, and press ENTER.

B Select the setting you want to sort by; Recent first, Oldest first, By title (AtZ), By title (ZtA), and press ENTER.

Items Details

All Movies Lists all titles (as above).

Browse Displays a list of genres, Quicklist, or folders (page 34).

Search Searches for a title using the on-screen keyboard (page 34).

Sort Reorders the titles by date or alphabet (see below).

DATA DVD

List ExitSYSTEM MENUSelect

1:31

1:02

1:31

1:25

1:33

1:26

1:57

1:36

1:18

1:18

1214 itemsAll Movies

Spider

Smoother

Sideway

Home

Alpinist

Electricity

Lemon Grove

Bridget

Finding Never-Ever Land

Meet My Mom

All Movies

Browse

Search

Sort

The Browse menu appears when you press <

Viewing All Titles . . . . . . . . . . . . . . . . . . . . . . 32

Browsing by Genre, Quicklist, or Folder . . . . . 34

Searching for a Title . . . . . . . . . . . . . . . . . . . . 34

Programming Playback (Quicklist) . . . . . . . . . 35

W atching M

ovie Files

Playing a title

a After step 3 of Viewing All Titles above, select the title you want to play, and press ENTER. The title starts playing. You can apply other playback settings to the selected title using the Options menu (see below).

To use the Options menu Press , instead of ENTER in the above step to display the Options menu settings applicable to the title in the given situation. In the above example, the following items are available.

Example: To apply Play from Beginning to the selected title

A Select Play from Beginning, and press ENTER.

To play in other play mode During playback, press PLAY MODE repeatedly. The selected item changes with each press: Time Search (page 26) Repeat Title Repeat Off See page 25 for details.

z Hint See page 24 for the remotes operations.

About the Movies (All Movies) Title List display

1Detailed information Displays details about the selected title. Date: Displays the recording year. Genre: Displays the genre name. Format: Displays the coding format.

2 List area Displays the title names of all content.

Items Details

Play from Beginning Starts playing the title you selected from the beginning.

Add to Quicklist Adds the selected title to the Quicklist.

List ExitSYSTEM MENUSelect

1214 items

1:31

1:02

1:31

1:25

1:33

1:26

1:57

1:36

1:18

1:18

All Movies

Spider

Smoother

Sideway

Home

Alpinist

Electricity

Lemon Grove

Bridget

Finding Never-Ever Land

Meet My Mom

Date : 2006 Genre : Adventure Format : MPEG

Play from Beginning

Add to Quicklist

Options

The Options menu appears when you select a title and press ,

List ExitSYSTEM MENUSelect

1:31

1:02

1:31

1:25

1:33

1:26

1:57

1:36

1:18

1:18

1214 itemsAll Movies

Spider

Smoother

Sideway

Home

Alpinist

Electricity

Lemon Grove

Bridget

Finding Never-Ever Land

Meet My Mom

Date : 2006 Genre : Adventure Format : MPEG

33

34

Browsing by Genre, Quicklist, or Folder

Narrow down the list of titles by selecting the category type (e.g., Folders), then the category.

a Press SYSTEM MENU.

b Select Title List, and press ENTER.

c Select Movies, and press ENTER.

d Press < to turn on the Browse menu.

e Select Browse, and press ENTER.

f Select the list you want to view from Genres, Quicklist, or Folders, and press ENTER. The list of genres/Quicklist/folders appears as above. For details about the Quicklist, see Programming Playback (Quicklist) (page 35).

g Select the genre/Quicklist/folder you want to view, and press ENTER.

z Hint You can select a title and start playback by pressing ENTER, or using the Options menu (press ,).

Searching for a Title

You can find the exact title, or titles with a similar name.

a Press SYSTEM MENU.

b Select Title List, and press ENTER.

c Select Movies, and press ENTER.

d Press < to turn on the Browse menu.

e Select Search, and press ENTER to turn on the above display.

f Enter the title name using the on-screen keyboard (see page 23).

z Hint You can select a title and start playback by pressing ENTER, or using the Options menu (press ,).

DATA DVD

ExitConfirm SYSTEM MENU

Folders

Winter games 2006

Interviews

2 items

DATA DVD

ExitSYSTEM MENUSelect

1:31

1:02

1:31

1:25

1:33

5 items

Say No

Sea

Sideway

Spider

Stay Alive

Search Results

A B

SHFT

DONE CANCEL SPC DEL CLR

C D E F G H I J K L M N O P Q R S T U V W X Y Z , . : ; 1 2 3 4 5 6 7 8 9 0 _ ( )

s_

Search results are narrowed down as more characters are entered

W atching M

ovie Files

Programming Playback (Quicklist)

Play your favorite titles in the order you like by making your own Quicklist.

a Press SYSTEM MENU.

b Select Title List, and press ENTER.

c Select Movies, and press ENTER.

d When the All Movies Title List appears, select the title you want to add to the top of the Quicklist, and press ,.

e Select Add to Quicklist from the Options menu, and press ENTER.

f Repeat step 4 and 5 to select all the desired titles. Select in the order you want to play. You can add the same title multiple times. The Quicklist can contain up to 25 titles.

g Press < to turn on the Browse menu.

h Select Browse, and press ENTER.

i Select Quicklist, and press ENTER to turn on the above display. The Quicklist Title List appears with the programmed content.

j Select the title you want to start playback, and press ENTER.

To remove the title from the Quicklist 1 Select the title you want to remove from the

displayed Quicklist, and press ,.

2 Select Remove, and press ENTER.

z Hint You can play the Quicklist content in other play modes by pressing PLAY MODE (page 25).

Note The Quicklist may be cleared after some operations (e.g., opening the disc tray, or turning off the player etc.).

DATA DVD

The Quicklist does not affect the original recording on the disc

List ExitSYSTEM MENUSelect

1:31

1:02

1:31

1:25

1:33

1:26

1:57

1:36

1:18

1:18

14 itemsQuicklist

Date : 2006 Genre : Adventure Format : MPEG

Spider

Smoother

Sideway

Home

Alpinist

Electricity

Lemon Grove

Bridget

Finding Never-Ever Land

Meet My Mom

35

36

Listening to Music Files

Use the Music Title List to browse through and play the MP3 track files on DATA DVDs. You can make a Quicklist of your favorites and play in various play modes.

Viewing All Artists

The Music Title List first displays a list of the artist names on the disc.

a Press SYSTEM MENU.

b Select Title List, and press ENTER.

c Select Music, and press ENTER. The above Artists display appears, showing all artist names (scrollable by pressing m). From Artists you can apply items to all tracks using the Browse menu (see below).

To use the Browse menu Press < after step 3 to display the items for the Music Title List. For operations, see the pages in parentheses. Available items differ depending on the display.

Example: To apply Sort to all tracks

A To display the list of tracks, select All Songs from the Browse menu and press ENTER.

B Press < to turn on the Browse menu.

C Select Sort, and press ENTER.

D Select the setting you want to sort by; Recent first, Oldest first, By title (AtZ), By title (ZtA), By artist (AtZ), By artist (ZtA), and press ENTER.

Items Details

All Songs Lists all tracks (page 37).

Browse Displays a list of artists, albums, genres, Quicklist, or folders (page 38).

Search Searches for a track using the on-screen keyboard (page 38).

Sort Reorders the tracks by alphabet, or year, etc. (see below).

Now Playing Displays the track information and the playback information during playback.

DATA DVD

PlayOptionsMain Menu ExitSYSTEM MENU

7 items

All Artists

Angela Simpson

Blue Glass

Bohemian Beat

Cela

Classic Remix

Commotion

Count Dra"Q"la

Albums

Albums

Albums

Albums

Albums

Albums

Albums

6

5

6

4

5

2

2

Artists

The Browse menu appears when you press <

Viewing All Artists . . . . . . . . . . . . . . . . . . . . . 36

Browsing by Artist, Album, Genre, Quicklist, or Folder . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Searching for a Track . . . . . . . . . . . . . . . . . . . 38

Programming Playback (Quicklist) . . . . . . . . . 39

Listening to M usic Files

Playing a track

a After step 3 of Viewing All Artists above, narrow down the list of tracks by selecting the artist, then the album. To list all tracks, press < and select All Songs from the Browse menu.

b Select the track you want to play, and press ENTER. The title starts playing. You can apply other playback settings to the selected track using the Options menu (see below).

To use the Options menu Press , instead of ENTER in the above step to display the Options menu settings applicable to the track in the given situation. In the above example, the following items are available.

Example: To apply Play Song to the selected track

A Select Play Song, and press ENTER.

To play in other play mode During playback, press PLAY MODE repeatedly. The selected item changes with each press: Repeat Track Repeat All Random Repeat Off See page 25 for details.

z Hints See page 24 for the remotes operations. Even after stopping playback, the player resumes playback from the

last track you played. Depending on the writing software used, the displayed track or album

names may be different from the characters you input.

Notes Playback time of MP3 audio tracks may not be displayed correctly. If you put an extension .MP3 to a non-MP3 file, the file may

accidentally play on the player. Note that such output may cause the connected device to malfunction.

Playback may not start immediately after skipping to another album. When using the Resume function on MP3 tracks, playback starts from

the beginning of the track.

About the Music (All Songs) Title List display

1Detailed information Displays details about the selected track. Artist: Displays the artist name. Album: Displays the album name. Genre: Displays the genre name. Format: Displays the coding format.

2 List area Displays overall content. Main area: Displays the track names. Sub area: Displays the total playback time of each

track.

About unplayable audio track files The player does not play the file if: The DATA DVD is not recorded in an MP3 format that

conforms to UDF (Universal Disk Format). The audio track file does not have the extension .MP3. The data is not formatted properly even though it has the

extension .MP3. The data is not MPEG-1 Audio Layer III data. The data is recorded in mp3PRO format. The file name contains characters other than numbers and

English alphabet.

Items Details

Play Song Starts playing the track you selected from the beginning.

Add to Quicklist Adds the selected track to the Quicklist.

PlayOptionsMain Menu ExitSYSTEM MENU

1214 items

9:31

8:00

7:31

3:55

6:33

5:26

4:57

9:36

6:18

6:18

All Songs

Never Let Me Down (Split Mix)

Policies of Truth

Shout in Rio

Home

Strangled

Rash (Spiritual Mix)

I Feel You (Remix)

Route 57 (Beatmasters Mix)

Free (DJ Remix)

Personal Note

Artist : Deep Green Album : Splash! Genre : Alternative Format : MP3

Play Song

Add to Quicklist

Options

The Options menu appears when you select a track and press ,

PlayOptionsMain Menu ExitSYSTEM MENU

Artist:Deep Green Album:Remixes 81-04 Genre:Alternative Format:MP3

1214 items

9:31

8:00

7:31

3:55

6:33

5:26

4:57

9:36

6:18

6:18

All Songs

Never Let Me Down (Split Mix)

Policies of Truth

Shout in Rio

Home

Strangled

Rash (Spiritual Mix)

I Feel You (Remix)

Route 57 (Beatmasters Mix)

Free (DJ Remix)

Personal Note

: Deep Green : Splash! : Alternative : MP3

37

38

Browsing by Artist, Album, Genre, Quicklist, or Folder

Narrow down the list of tracks by selecting the category type (e.g., Genres), then the category.

a Press SYSTEM MENU.

b Select Title List, and press ENTER.

c Select Music, and press ENTER.

d Press < to turn on the Browse menu.

e Select Browse, and press ENTER.

f Select the list you want to view from Artists, Albums, Genres, Quicklist or Folders, and press ENTER. The list of artists/albums/genres/Quicklist/folders appears as above. For details about the Quicklist, see Programming Playback (Quicklist) (page 39).

g Select the artist/album/genre/Quicklist/ folder you want to view, and press ENTER.

z Hint You can select a track from the list of tracks, and start playback by pressing ENTER, or using the Options menu (press ,).

Searching for a Track

You can find the exact track, or tracks with a similar name.

a Press SYSTEM MENU.

b Select Title List, and press ENTER.

c Select Music, and press ENTER.

d Press < to turn on the Browse menu.

e Select All Songs, and press ENTER.

f Press < to turn on the Browse menu.

g Select Search, and press ENTER to turn on the above display.

h Enter the track name using the on-screen keyboard (see page 23).

z Hints You can select a track from the search result, and start playback by

pressing ENTER, or using the Options menu (press ,). You can search for a genre, artist, album, or folder name from each

Title List (e.g., Genres).

DATA DVD

PlayOptionsMain Menu ExitSYSTEM MENU

20 items

All Genres

Alternative

Blues

Books And Spoken

Celtic

Classical

Comedy

Country

Dance

Dark

Songs

Songs

Songs

Songs

Songs

Songs

Songs

Songs

Songs

2876

195

16

304

841

32

2

460

60

Genres

Genres without content do not appear in the list

DATA DVD

ExitSYSTEM MENUSelect

7 items

Raga

Raging Plants

Ragamufin

Ree

Rise

Rose Bed

Rule the World

9:31

8:00

7:31

7:32

6:33

6:34

6:35

Search Results

A B

SHFT

DONE CANCEL SPC DEL CLR

C D E F G H I J K L M N O P Q R S T U V W X Y Z , . : ; 1 2 3 4 5 6 7 8 9 0 _ ( )

R

Search results are narrowed down as more characters are entered

Listening to M usic Files

Programming Playback (Quicklist)

Play your favorite tracks in the order you like by making your own Quicklist.

a Press SYSTEM MENU.

b Select Title List, and press ENTER.

c Select Music, and press ENTER.

d Press < to turn on the Browse menu.

e Select All Songs, and press ENTER.

f When the All Songs Title List appears, select the track you want to add to the top of the Quicklist, and press ,.

g Select Add to Quicklist from the Options menu, and press ENTER.

h Repeat step 6 and 7 to select all the desired tracks. Select in the order you want to play. You can add the same track multiple times. The Quicklist can contain up to 25 tracks.

i Press < to turn on the Browse menu.

j Select Browse, and press ENTER.

k Select Quicklist, and press ENTER to turn on the above display. The Quicklist Title List appears with the programmed content.

l Select the track you want to start playback, and press ENTER.

To remove the title from the Quicklist 1 Select the track you want to remove from the

displayed Quicklist, and press ,.

2 Select Remove, and press ENTER.

z Hint You can play the Quicklist content in other play modes by pressing PLAY MODE (page 25).

Note The Quicklist may be cleared after some operations (e.g., opening the disc tray, or turning off the player etc.).

DATA DVD

The Quicklist does not affect the original recording on the disc

PlayOptionsMain Menu ExitSYSTEM MENU

3 itemsQuicklist

9:31

8:00

7:31

Never Let Me Down (Split Mix)

Policies of Truth

Shout in Rio

Artist : Deep Green Album : Splash! Genre : Alternative Format : MP3

39

40

Viewing Photo Files

Use the Photos Title List to view the JPEG images on DATA DVDs. You can reorder the files and start playing a slideshow.

Viewing All Folders

The Photos Title List first displays all the folders on the disc.

a Press SYSTEM MENU.

b Select Title List, and press ENTER.

c Select Photos, and press ENTER. The above Folders display appears, showing all folders (scrollable by pressing m). From Folders you can apply items to all files using the Browse menu (see below).

To use the Browse menu Press < after step 3 to display the items for Photos Title List. For operations, see the pages in parentheses. Available items differ depending on the display.

Example: To apply Sort to all files

A To display the list of all files, select All Photos from the Browse menu and press ENTER.

B Move the highlight to the left most row, and press < to turn on the Browse menu.

C Select Sort, and press ENTER.

D Select the setting you want to sort by; Recent first, Oldest first, By title (AtZ), By title (ZtA), and press ENTER.

Items Details

All Photos Displays all files in alphabetical order (page 41).

Browse Displays a list of dates, Quicklist, or folders (page 42).

Search Searches for a file using the on-screen keyboard (page 42).

Sort Reorders the files by date or alphabet (see below).

DATA DVD

ExitConfirm SYSTEM MENU

Folders

Kurobe-dam 2005

Jungfraujoch 2006

2 items

The Browse menu appears when you press < while on the leftmost row

Viewing All Folders . . . . . . . . . . . . . . . . . . . . . 40

Browsing by Date, Quicklist, or Folder . . . . . . 42

Searching for a Photo. . . . . . . . . . . . . . . . . . . 42

Programming a Slideshow Playback (Quicklist) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

View ing Photo Files

Playing a slideshow

a After step 3 of Viewing All Folders above, press < and select All Photos from the Browse menu.

b Select the file you want to start from, and press ENTER to turn on the Options menu.

c Select Slideshow, and press ENTER. Slideshow starts. You can apply other playback settings to the selected file using the Options menu (see below).

To use the Options menu Available Options menu settings differ depending on the situation. In the above example of the use of the Options menu, the following items are available.

To play in other play mode During playback, press PLAY MODE repeatedly. The selected item changes with each press: Repeat All Random Repeat Off See page 25 for details. Note that in Random mode, only files in the list area (20 files maximum) are randomly played.

z Hints See page 24 for the remotes operations. Even after stopping playback, the player resumes playback from the

last file you played.

Note The photos may appear slowly depending on the size and the number of files.

About the Photos (All Photos) Title List display

1Detailed information Displays details about the selected file. File: Displays the file name. Date: Displays the shooting date. Resolution: Displays the picture resolution in width

height. Format: Displays the recording format.

2 List area Displays overall photo content in thumbnail.

About unplayable photo files The player does not play the file if: The DATA DVD is not recorded in a JPEG format that

conforms to UDF (Universal Disk Format). The photo file is not recorded in a format that conforms to the

DCF*. The file has an extension other than .JPEG. The image is larger than 4,096 (width) 4,096 (height) in

normal mode, or progressive JPEG. The image does not fit the screen (the image is reduced). The file name contains characters other than numbers and

English alphabet. Even when the above are not applicable, some files may not

play depending on the recording condition or the method (e.g., writer software).

Files may not play on this player if edited on a PC. * Design rule for Camera File system: Image standards for digital

cameras regulated by JEITA (Japan Electronics and Information Technology Industries Association).

Items Details

Slideshow Starts playing a slideshow as above.

Add to Quicklist Adds the selected file to the Quicklist for later slideshow playback.

ExitConfirm SYSTEM MENU

1214 itemsAll Photos

File : DSC00434.jpg Date : 7/23/2006 Resolution: 293 x 196 Format: JPEG

Slideshow

Add to Quicklist

Options

The Options menu appears when you select a file and press ENTER

ExitConfirm SYSTEM MENU

File:Summer of '06.jpg Date:July/23/2006 Resolution:196x298 pixels Format:JPEG

1214 itemsAll Photos

: DSC00434.jpg : 7/23/2 06

293 x 196 JPEG

41

42

Browsing by Date, Quicklist, or Folder

Narrow down the list of files by selecting the category type (e.g., Date), then the category.

a Press SYSTEM MENU.

b Select Title List, and press ENTER.

c Select Photos, and press ENTER.

d Press < to turn on the Browse menu.

e Select Browse, and press ENTER.

f Select the list you want to view from Date, Quicklist, or Folders and press ENTER. The list of date/Quicklist/folders appears as above. For details about the Quicklist, see Programming a Slideshow Playback (Quicklist) (page 43).

g Select the date/Quicklist/folder you want to view, and press ENTER.

z Hint You can select a file and start slideshow by using Options menu (press ,).

Searching for a Photo

You can find the exact file, or files with a similar name.

a Press SYSTEM MENU.

b Select Title List, and press ENTER.

c Select Photos, and press ENTER.

d Press < to turn on the Browse menu.

e Select All Photos, and press ENTER.

f Move the highlight to the leftmost row, and press < to turn on the Browse menu.

g Select Search, and press ENTER to turn on the above display.

h Enter the file name using the on-screen keyboard (see page 23).

z Hint You can select a file and start slideshow by using Options menu (press ,).

DATA DVD

ExitConfirm SYSTEM MENU

File:Summer of '06.jpg Date:July/23/2006 Resolution:196x298 pixels Format:JPEG

10 itemsYear

2007

2006

2005

2004

2003

2002

2001

2000

1999

1998

DATA DVD

ExitSYSTEM MENUSelect

7 itemsSearch Results

A B

SHFT

DONE CANCEL SPC DEL CLR

C D E F G H I J K L M N O P Q R S T U V W X Y Z , . : ; 1 2 3 4 5 6 7 8 9 0 _ ( )

R_

Search results are narrowed down as more characters are entered

View ing Photo Files

Programming a Slideshow Playback (Quicklist)

Play a slideshow in the order you like by making your own Quicklist.

a Press SYSTEM MENU.

b Select Title List, and press ENTER.

c Select Photos, and press ENTER.

d Press < to turn on the Browse menu.

e Select All Photos, and press ENTER.

f When the All Photos Title List appears, select the file you want to add to the top of the Quicklist, and press ENTER.

g Select Add to Quicklist from the Options menu, and press ENTER.

h Repeat step 6 and 7 to select all the desired files. Select in the order you want to play. You can add the same file multiple times. The Quicklist can contain up to 25 files.

i Move the highlight to the leftmost row, and press < to turn on the Browse menu.

j Select Browse, and press ENTER.

k Select Quicklist, and press ENTER to turn on the above display. The Quicklist Title List appears with the programmed content.

l Select the file you want to start playback, and press ENTER.

m Select Slideshow from the Options menu, and press ENTER.

To remove from the Quicklist 1 Select the file you want to remove from the

displayed Quicklist, and press ENTER.

2 Select Remove, and press ENTER.

z Hint You can play the Quicklist content in other play modes by pressing PLAY MODE (page 25).

Note The Quicklist may be cleared after some operations (e.g., opening the disc tray, or turning off the player etc.).

DATA DVD

The Quicklist does not affect the original recording on the disc

ExitConfirm SYSTEM MENU

22 itemsQuicklist

File : DSC00434.jpg Date : 7/23/2006 Resolution: 293 x 196 Format: JPEG

43

44

Changing the Initial Settings

Select Setup from the System Menu when you need to change the settings of the player (e.g., when changing the connected device or the audio/video output, etc.). The last part of this section explains how to return all of these settings to their factory defaults.

Note Playback settings described in this section may not work when there is any preset playback setting in the disc. The discs playback settings take priority over the players playback settings.

Using the Setup Displays

From the System Menu, enter the Setup displays to change the settings of the player.

a Press SYSTEM MENU while the player is stopped.

b Select Setup, and press ENTER.

c Select the Setup display you want to use, from Video Setup, Audio Setup, Language, Parental Control, Speakers, or Options, and press ENTER. The Setup display appears with the related items. Note that the display switches to the screen saver if you do not operate for 15 minutes.

d Select the item you want to change, and press ENTER. Refer to the explanations in the following sections.

To return to the previous display Press RETURN.

BD DVD DATA DVD CD

Use to select an item, then press [RR] or ENTER.

Confirm ExitSYSTEM MENU

Setup

Video Setup

Audio Setup

Language

Parental Control

Speakers

Options

TV Type

4:3 Video Out

DVD Aspect Ratio

YCbCr/RGBPC(HDMI)

24p Output

16:9

Normal

Letter Box

Y, Cb, Cr

Off

Using the Setup Displays . . . . . . . . . . . . . . . . 44

Video Setup . . . . . . . . . . . . . . . . . . . . . . . . . . 45

Audio Setup . . . . . . . . . . . . . . . . . . . . . . . . . . 47

Language . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

Parental Control . . . . . . . . . . . . . . . . . . . . . . . 50

Speakers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

Options. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

Resetting the Player . . . . . . . . . . . . . . . . . . . . 53

Changing the Initial Settings

ntinued

Video Setup

Underlined items are the default settings.

Note TV Type and DVD Aspect Ratio can be set when video output resolution is 480i/480p.

TV Type 4:3 4:3 screen TV.

16:9 Wide-screen TV, or a TV with a wide mode function.

Select your TV type.

4:3 Video Out Full Displays a 4:3 screen picture in 16:9 aspect ratio.

Normal Displays a 4:3 screen picture in 4:3 aspect ratio with black bands on the sides. Select

this if your TV does not have a 4:3 screen mode.

Select the display configuration for a 4:3 screen picture on a 16:9 wide screen TV.

DVD Aspect Ratio Letter Box Displays a wide picture with black bands on the top and

bottom.

Pan & Scan Displays a full-height picture on the entire screen, with

trimmed sides.

Select the display configuration for a 16:9 DVD picture on a 4:3 screen TV (selectable when TV Type is set to 4:3). Note that the aspect ratio is fixed on some discs. For example, a 4:3 letterbox picture may appear even when Pan & Scan is selected.

YCbCr / RGBPC (HDMI) Y, Cb, Cr Select this when connecting to an HDMI device.

RGB (16-235) Select this when connecting to a device with an HDCP-compliant DVI jack.

RGB (0-255) Select this when connecting to an RGB (0-255) device.

Select the type of output from the HDMI OUT jack.

24p Output On Sends 1920 1080p/24 Hz video signals when playing Film-based materials on BD-

ROMs (720p/24 Hz or 1080p/24 Hz). Select this when the connection applies.

Off Select this for any other connection.

For connection to a 1080/24p-compatible TV using the HDMI OUT jack.

,co

45

46

To set the video output resolution Press VIDEO FORMAT repeatedly to select the desired resolution. Note that the resolution differs depending on the display device, connecting jack and the source material as below.

*1 Outputs in the same resolution and frequency as recorded on the disc. *2 1080/24p video signals are not output from the COMPONENT VIDEO OUT jacks. *3 Outputs in the resolution of the original setting (720p or 1080i) when the DVD is not copy guarded.

Notes If the picture is not clear, natural or to your satisfaction, try another resolution that suits the disc and your TV/projector, etc. For the details, refer also

to the instruction manual supplied with the TV/projector, etc. 480i or 480p video signals may be output when you connect to the COMPONENT VIDEO OUT jacks and play some copy-guarded BDs/DVDs. To

enjoy the HD quality resolution in this case, connect the display device to the HDMI OUT jack using an HDMI cord. Even when you select a setting other than Auto, the player automatically adjusts the video signals if the TV cannot accept the set resolution.

To output the 1080/24p video signals A 1080/24p-compatible TV is required for this setting.

1 Set 24p Output in Video Setup to On (page 45).

2 Press VIDEO FORMAT repeatedly to select Auto or Source Direct.

Note If there is no picture, press VIDEO FORMAT repeatedly until the picture appears correctly.

HDMI OUT COMPONENT VIDEO OUT VIDEO/S VIDEO

Auto Automatically selects the recommended resolution acceptable for your TV.

480i 480i

480i 480i 480i 480i

480p 480p 480p 480i

720p 720p BD:720p, DVD:480p*3 480i

1080i 1080i BD:1080i, DVD:480p*3 480i

1080p 1080p 480i 480i

Source Direct Output differs depending on source material*1

Output differs depending on source material*2

480i

Connecting jackSettings

Changing the Initial Settings

ntinued

Audio Setup

Underlined items are the default settings. Since many factors affect the type of audio output, see also About the audio output signals on page 48.

Dolby Digital Dolby Digital Select this when connecting to a device with a built-in Dolby Digital decoder.

Downmix PCM Converts to output Linear PCM signals. Select this when connecting to a device

without a built-in Dolby Digital decoder.

Select the audio signals output when playing Dolby Digital discs. This setting affects the output from the DIGITAL OUT (COAXIAL or OPTICAL) jack.

DTS DTS Select this when connecting to a device with a built-in DTS decoder.

Downmix PCM Converts to output Linear PCM signals. Select this when connecting to a device

without a built-in DTS decoder.

Select the audio signals output when playing DTS discs. This setting affects the output from the DIGITAL OUT (COAXIAL or OPTICAL) jack.

DTS Downmix Stereo Downmixes multi-channel audio signals for two channel stereo.

Lt/Rt Allows you to hear surround sound when the connected device has a built-in Dolby

Pro Logic decoder.

Select the type of 2-channel signals when down-mixed from multi-channel DTS sources (effective for audio connections when DTS is set to Downmix PCM).

Audio (HDMI) Auto Normally, select this. Outputs audio signals according to the status of the connected

HDMI device.

PCM Converts all audio signals to Linear PCM.

Select the output method from the HDMI OUT jack.

,co

47

48

About the audio output signals The audio output differs as follows, depending on the source, output jack, and the selected settings.

*1 2 Channel and 5.1 Channel are selectable under Audio Output Mode in Speakers Setup (page 51). *2 PCM : when Dolby Digital or DTS in Audio Setup is set to Downmix PCM (page 47).

Bitstream : when Dolby Digital or DTS in Audio Setup is set to Dolby Digital or DTS (page 47). *3 Selectable under Audio (HDMI) in Audio Setup (page 47). *4 Selectable under Audio (HDMI) in Audio Setup (page 47). Resulting output may differ depending on the connected HDMI device. *5 When the sampling frequency is 192 kHz, the player downmixes to 2ch signals even if the disc or source is 5.1ch. *6 Outputs 7.1ch LPCM signals decoded from Dolby Digital Plus audio stream.

AUDIO OUT L/R jacks*1 DIGITAL OUT (OPTICAL/ COAXIAL) jacks*2 HDMI OUT jack*3

2ch 5.1ch PCM Bitstream PCM*4 Auto*4

BD- ROM

Linear PCM 2ch 2ch 2ch 2ch LPCM 2ch LPCM 2ch LPCM 2ch LPCM

5.1ch*5 2ch Downmix 5.1ch 2ch Downmix LPCM

2ch Downmix LPCM

5.1ch LPCM 5.1ch LPCM

7.1ch 2ch Downmix 5.1ch Downmix

2ch Downmix LPCM

2ch Downmix LPCM

7.1ch LPCM 7.1ch LPCM

Dolby Digital 2ch Downmix 5.1ch 2ch Downmix LPCM

Dolby Digital 5.1ch LPCM Dolby Digital

Dolby Digital Plus 2ch Downmix 5.1ch 2ch Downmix LPCM

Dolby Digital 7.1ch LPCM*6 Dolby Digital

Dolby TrueHD 2ch Downmix 5.1ch 2ch Downmix LPCM

Dolby Digital 5.1ch LPCM Dolby Digital

DTS 2ch Downmix 5.1ch 2ch Downmix LPCM

DTS 5.1ch LPCM DTS

DTS-HD 2ch Downmix 5.1ch 2ch Downmix LPCM

DTS 5.1ch LPCM DTS

DVD Linear PCM 2ch 2ch 2ch LPCM 2ch LPCM 2ch LPCM 2ch LPCM

Dolby Digital 2ch Downmix 5.1ch 2ch Downmix LPCM

Dolby Digital 5.1ch LPCM Dolby Digital

DTS 2ch Downmix 5.1ch 2ch Downmix LPCM

DTS 5.1ch LPCM DTS

MPEG 2ch 2ch 2ch LPCM 2ch LPCM 2ch LPCM

CD Linear PCM 2ch 2ch 2ch 2ch LPCM 2ch LPCM 2ch LPCM 2ch LPCM

DTS 2ch Downmix 5.1ch 2ch Downmix LPCM

DTS 5.1ch LPCM DTS

Jacks/ settings

Disc/source

Changing the Initial Settings

Language

Underlined items are the default settings.

Notes When you select a language in Audio, Subtitles, BD/DVD Menu

that is not recorded on the disc, one of the recorded languages is automatically selected.

Playback settings stored in the disc take priority over these settings.

OSD English Displays the menus and messages in English.

Franais Displays the menus and messages in French.

Select your language for the player on-screen displays.

Audio English Plays the soundtrack in English.

French Plays the soundtrack in French.

Other See Language Code List on page 68 and enter the code for your language.

Select the default soundtrack language for BD-ROMs/DVD VIDEOs.

Subtitles English Displays the subtitles in English.

French Displays the subtitles in French.

Other See Language Code List on page 68 and enter the code for your language.

Select the default subtitle language for BD- ROMs/DVD VIDEOs.

BD/DVD Menu w/Subtitle Displays BDs/DVDs menus in the same language as the subtitle language.

English Displays BDs/DVDs menus in English.

French Displays BDs/DVDs menus in French.

Other See Language Code List on page 68 and enter the code for your language.

Select the default menu language for BD- ROMs/DVD VIDEOs.

Subtitle Display On Turns on the subtitles.

Off Turns off the subtitles.

49

50

Parental Control

This function limits playback of DVD VIDEOs and BD-ROMs. To activate, see Locking a Disc (page 29). The default settings are underlined.

Notes You cannot limit playback if the disc does not have the Parental Control

function. If you forget the password for Parental Control, you will need to reset

the player (page 53). Note that all the settings you made also return to their defaults.

Change Password (Set Password) Next Screen Set or change the password for the Parental Control function. You will be asked for

the password when playing restricted discs or when changing the control level.

DVD Parental Control Change Level Set the control level. The display asks for the password if the discs pre-determined

level exceeds the limit you set. The default setting is Off.

DVD Country Code This ensures that you see the scenes intended for your residential area. The default

setting is us (2119).

BD Parental Control Change Age Restriction Set the control level. The display asks for the password if the discs pre-determined

age restriction is higher than the age you set. The default setting is 255.

BD Country Code This ensures that you see the scenes intended for your residential area when playing

BD-ROMs. The default setting is us (2119).

Changing the Initial Settings

Speakers

The following items are necessary when using the 5.1CH OUTPUT jacks. The default settings are underlined.

Audio Output Mode 2 Channel Select this when connecting to an AV amplifier (receiver) using the AUDIO OUT (L/

R) jacks.

5.1 Channel Select this when connecting to an AV amplifier (receiver) using the 5.1CH OUTPUT

jacks.

For analog connection.

Speaker Setup Next Screen 1 Select the speaker setting that needs adjusting by pressing M/m.

C (center speaker): Yes or No Ls/Rs (left surround speaker/right surround speaker): Yes or No L/R (left front speaker/right front speaker): Large or Small

2 Adjust the setting by pressing

to No. 3 Press ENTER to save the adjustments.

This setting affects the output from the 5.1CH OUTPUT jacks.

51

52

Options

Underlined items are the default settings.

On Screen Display On Displays playback status.

Off Playback status is not displayed.

Select whether to display the playback status on the screen (Stop, Play, etc.).

Auto Power Off On Turns off the player when the player is left in stop or pause mode without operation

for 30 minutes. Off The player remains turned on with or without operation.

Select whether to activate the Auto Power Off function of the player.

Easy Setup Start Press ENTER and see page 18. Re-runs the Easy Setup to make the basic

settings.

HDMI Control On Activates the function. Off Turns off the function.

Select whether to activate the HDMI Control function of the player (page 11).

Hybrid Disc Playback Layer BD Plays BD layer. DVD Plays DVD layer. CD Plays CD layer.

Select the layer priority when playing a Hybrid Disc. Remove the disc when you change the setting.

Changing the Initial Settings

Resetting the Player

You can return all of the player settings to their factory defaults.

a When the power is on, hold down x on the front panel, and press @/1. The player turns off, and all of the settings return to their factory defaults.

x@/1

HDMI HD FL OFF

53

54

Additional Information

Troubleshooting

If you experience any of the following difficulties while using the player, use this troubleshooting guide to help remedy the problem before requesting repairs. Should any problem persist, consult your nearest Sony dealer (For customers in the USA only).

Power

The power does not turn on. , Check that the power cord is connected securely. , It takes a short while before the player turns on.

Picture

There is no picture/picture noise appears. , Re-connect the connecting cord securely. , The connecting cords are damaged. , Check the connection to your TV (page 10) and switch the

input selector on your TV so that the signal from the player appears on the TV screen.

, The disc is dirty or flawed. , If the picture output from your player goes through your

VCR to get to your TV or if you are connected to a combination TV/VIDEO player, the copy-protection signal applied to some BD/DVD programs could affect picture quality. If you still experience problems even when you connect your player directly to your TV, try connecting your player to your TVs S VIDEO input (page 10).

, The player is connected to an input device that is not HDCP- compliant (the HDMI indicator on the front panel does not light up). See page 11.

, If the HDMI OUT jack or the COMPONENT VIDEO OUT jacks are used for video output, changing the output resolution may solve the problem (page 46). Press VIDEO FORMAT repeatedly until the picture appears correctly.

, Depending on the disc, the picture quality may be poor when the VIDEO FORMAT setting is set to other than 480i, even when the player is connected to a progressive or HD TV using a component cord or an HDMI cord. If this happens, press VIDEO FORMAT repeatedly to switch to 480i.

, When playing a double-layer DVD, the video and audio may be momentarily interrupted at the point where the layers switch.

There is no picture or picture noise appears when connected to the HDMI OUT jack. , Try the following: 1Turn the player off and on again. 2Turn the connected equipment off and on again. 3Disconnect and then connect the HDMI cord again.

, If the HDMI OUT jack is used for video output, changing the video output resolution may solve the problem (page 46). Press VIDEO FORMAT repeatedly until the picture appears correctly.

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . 54

Self-Diagnosis Function . . . . . . . . . . . . . . . . . 57

Index to Parts and Controls . . . . . . . . . . . . . . 58

GNU License Information . . . . . . . . . . . . . . . . 60

Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . 67

Language Code List . . . . . . . . . . . . . . . . . . . . 68

Parental Control Country/Area Code List . . . . 69

Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70

Additional Inform ation

ntinued

The picture does not fill the screen, even though the aspect ratio is set in TV Type under Video Setup. , The aspect ratio of the disc is fixed on your BD/DVD. See

page 45.

The dark area of the picture is too dark/the bright area is too bright or unnatural. , Set Video Control in A/V Control to Standard

(default) (page 28). , Adjust each picture setting for Memory in Video

Control to midpoint (default) (page 28).

Sound

There is no sound. , The disc is dirty or flawed. , Re-connect the connecting cord securely. , The connecting cord is damaged. , The player is connected to the wrong input jack on the

amplifier (receiver) (page 12). , The amplifier (receiver) input is not correctly set. , The player is in pause mode or in Slow-motion Play mode. , The player is in scan mode. , If the audio signal does not come through the DIGITAL

OUT (OPTICAL or COAXIAL)/HDMI OUT jack, check the audio settings (page 47).

, The equipment connected to the HDMI OUT jack does not conform to the audio signal format, in this case set Audio (HDMI) in Audio Setup to PCM (page 47).

The sound is not output correctly. , Check the Audio Output Mode in Speakers Setup

(page 51) if the AUDIO OUT (L/R) jacks or the 5.1CH OUTPUT jacks are used for audio connection.

No sound is output from the HDMI OUT jack , Try the following: 1Turn the player off and on again. 2Turn the connected equipment off and on again. 3Disconnect and then reconnect the HDMI cord.

, The HDMI OUT jack is connected to a DVI device (DVI jacks do not accept audio signals).

The sound volume is low. , The sound volume is low on some BDs/DVDs. The sound

volume may improve if you adjust the Audio Control setting in A/V Control (page 27).

Operation

The remote does not function. , The batteries in the remote are weak (page 16). , There are obstacles between the remote and the player. , The distance between the remote and the player is too far. , The remote is not pointed at the remote sensor on the player.

The disc does not play. , The disc is turned over. Insert the disc with the playback side

facing down.

, The disc is skewed. , The player cannot play certain discs (page 6). , The region code on the BD/DVD does not match the player. , Moisture has condensed inside the player (page 3). , The player cannot play a recorded disc that is not correctly

finalized (page 6). , The movie file size exceeds 2 GB. , The file on the DATA DVD contains characters other than

numbers and English alphabet.

The MP3 audio track file cannot be played

, The DATA DVD is not recorded in the MP3 format that conforms to UDF (Universal Disk Format).

, The audio track file does not have the extension .MP3. , The data is not formatted properly even though it has the

extension .MP3. , The data is not MPEG-1 Audio Layer III data. , The player cannot play audio tracks in mp3PRO format. , Characters other than numbers and English alphabet are

contained in the file name.

The photo file cannot be played , The disc is dirty or flawed. , The DATA DVD is not recorded in a JPEG format that

conforms to UDF (Universal Disk Format). , The file has an extension other than .JPEG or .JPG. , The image is larger than 4,096 (width) 4,096 (height) in

normal mode. (Some progressive JPEG files cannot be displayed even if the file size is within this specified capacity.)

, The image does not fit the screen (the image is reduced). , The photo file format does not conform to DCF* (page 41). , Characters other than numbers and English alphabet are

contained in the file name. * Design rule for Camera File system: Image standards for digital

cameras regulated by JEITA (Japan Electronics and Information Technology Industries Association).

The file name is not correctly displayed. , The player can only display numbers and alphabet. Other

characters may be displayed differently. , Depending on the writing software used, the input characters

may be displayed differently.

The disc does not start playing from the beginning. , Random Play or Repeat Play is selected (page 25). , Resume play mode is on (page 20).

The player starts playing the disc automatically. , The disc features an auto playback function.

Playback stops automatically. , While playing discs with an auto pause signal, the player

stops playback at the auto pause signal.

(page 36).

(page 40).

,co

55

56

Some functions such as Stop, Search, Slow- motion Play, Repeat Play, or Random Play cannot be performed. , Depending on the disc, you may not be able to do some of

the operations above. Refer to the operating manual that comes with the disc.

The language for the soundtrack cannot be changed. , Try using the BDs or DVDs menu instead of the direct

selection button on the remote (page 21). , Multi-lingual tracks are not recorded on the BD/DVD being

played. , The BD/DVD prohibits the changing of the language for the

sound track.

The subtitle language cannot be changed or turned off. , Try using the BDs or DVDs menu instead of the direct

selection button on the remote (page 21). , Multi-lingual subtitles are not recorded on the BD/DVD

being played. , The BD/DVD prohibits the changing of subtitles.

The angles cannot be changed. , Try using the BDs or DVDs menu instead of the direct

selection button on the remote (page 21). , Multi-angles are not recorded on the BD/DVD being played. , The BD/DVD prohibits changing of the angles.

The HDMI Control function does not work. , If the HDMI indicator on the front panel does not light up,

check the HDMI connection (page 11, 15). , Set HDMI Control to On (page 52). , Make sure that the connected component is compatible with

the HDMI Control function. Refer to the operating instructions of the component for details.

, Check that the power cord of the connected component is connected securely.

, Check the connected components setting for the HDMI Control function. Refer to the operating instructions of the component.

, If you change the HDMI connection, connect and disconnect the power cord, or if power failure occurs, set HDMI Control to Off, then set HDMI Control to On (page 52).

, For details on the HDMI Control function, see About the BRAVIA Theatre Sync features (for HDMI connections only) (page 11).

The display language on the screen switches automatically. , When HDMI Control is set to On (page 52), the display

language on the screen automatically switches according to the language setting of the connected TV (if you change the setting on your TV, etc).

The player does not operate properly. , When static electricity, etc., causes the player to operate

abnormally, unplug the player.

The disc tray does not open and LOCK appears on the front panel display. , Contact your Sony dealer or local authorized Sony service

facility.

The disc tray does not open and you cannot remove the disc even after you press Z. , Turn on the player.

As soon as POWER ON appears on the front panel display, press x on the player (not the remote) repeatedly until the tray opens. Repeat the above procedure several times if the tray does not open on the first try.

UNPLAYABLE appears when playing a DATA DVD. , See also The photo file cannot be played or The MP3

audio track file cannot be played (page 55). , The MP3 audio track/JPEG image file you want to play/view

is damaged. , The data is not MPEG-1 Audio Layer III data. , The JPEG image file format does not conform to DCF*

(page 41). , The JPEG image file has the extension .JPG or .JPEG,

but is not in JPEG format. * Design rule for Camera File system: Image standards for digital

cameras regulated by JEITA (Japan Electronics and Information Technology Industries Association).

The player does not accept any button. , Hold down \/1 on the player for more than five seconds

until the indicators on the front panel display turn off.

Additional Inform ation

Self-Diagnosis Function

When the self-diagnosis function is activated to prevent the player from malfunctioning, the ERR error code appears on the front panel display indicating the cause.

Error code Cause and/or corrective action

AACS ERR AACS read failure. tRemove the protected disc.

LSI1 ERR LSI2 ERR LSI3 ERR MEM ERR FLASH ERR ROM ERR

tContact your nearest Sony dealer or local authorized Sony service facility and give the error code.

57

58

Index to Parts and Controls

Buttons on the remote and the player have the same function if they have the same or similar name. For details, see the pages in parentheses.

Front panel

HDMI HD FL OFF

A @/1 (20) Turns on the player, or sets to standby mode.

B Disc tray (20)

C H, X, x (20) Starts, pauses, or stops playback.

D ./> (24) Skips to the previous/next chapter or track. Scans forward or backwards when held down.

E A (20) Opens or closes the disc tray.

F HDMI indicator (11) Lights up when an HDMI device is connected. HD indicator (11) Lights up when outputting 720p/1080i/1080p

video signals. FL OFF indicator (24) Lights up when the front panel display and other

indicators on the front panel are turned off.

G Remote sensor (16)

H Blu-ray Disc indicator Lights up when a BD is recognized. Lights up for a few seconds when the player is

turned on.

I Front panel display (59)

Additional Inform ation

Front panel display

z Hint You can change the brightness of the front panel display by pressing DIMMER (page 24).

The playback information is displayed as follows.

Example: When playing a DVD VIDEO or a BD-ROM

A Current title number

B Current chapter number Note that the chapter number is not displayed if the titles elapsed time exceeds 10 hours.

C Elapsed time of the title

Rear panel For connections, see page 10 to 16.

A H

Lights up during playback.

B Playback information

AC IN

VIDEO OUT

COMPONENT VIDEO OUT

DIGITAL OUT PCM/DTS/DOLBY DIGITAL

5.1CH OUTPUT

VIDEO

Y

L

R

AUDIO OUT

L

R

WOOFER

COAXIAL OPTICAL

FRONT REAR CENTER

PB

PR

S VIDEO

HDMI OUT

A AC IN terminal (16)

B HDMI OUT jack (11, 12, 15)

C VIDEO OUT (VIDEO/S VIDEO) jacks (10)

D COMPONENT VIDEO OUT (Y/PB/PR) jacks (10)

E DIGITAL OUT (COAXIAL/OPTICAL) jacks (13, 14)

F AUDIO OUT (L/R) jacks (13, 14)

G 5.1CH OUTPUT (FRONT L/R, REAR L/R, CENTER, WOOFER) jacks (14)

59

60

GNU License Information

Regarding the GNU General Public License The software programs used on this component include the GNU/Linux system. The GNU/Linux system contains software licensed for use based on the terms of a GNU General Public License. If necessary, the user may request the source code for this licensed software. The source code is available on our website. Access the following URL to download: http://www.sony.net/Products/Linux Please refrain from making inquiries about the source code content. Details of the GNU General Public License can be found at the GNU website (http://www.gnu.org).

GNU General Public License Version 2, June 1991 Copyright (C) 1989, 1991 Free Software Foundation, Inc. 59 Temple Place - Suite 330, Boston, MA 02111- 1307, USA Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed.

Preamble The licenses for most software are designed to take away your freedom to share and change it. By contrast, the GNU General Public License is intended to guarantee your freedom to share and change free software-to make sure the software is free for all its users. This General Public License applies to most of the Free Software Foundations software and to any other program whose authors commit to using it. (Some other Free Software Foundation software is covered by the GNU Lesser General Public License instead.) You can apply it to your programs, too. When we speak of free software, we are referring to freedom, not price. Our General Public Licenses are designed to make sure that you have the freedom to distribute copies of free software (and charge for this service if you wish), that you receive source code or can get it if you want it, that you can change the software or use pieces of it in new free programs; and that you know you can do these things. To protect your rights, we need to make restrictions that forbid anyone to deny you these rights or to ask you to surrender the rights. These restrictions translate to certain responsibilities for you if you distribute copies of the software, or if you modify it. For example, if you distribute copies of such a program, whether gratis or for a fee, you must give the recipients all the rights that you have. You must make sure that they, too, receive or can get the source code. And you must show them these terms so they know their rights. We protect your rights with two steps: (1) copyright the software, and (2) offer you this license which gives you legal permission to copy, distribute and/or modify the software. Also, for each authors protection and ours, we want to make certain that everyone understands that there is no warranty for this free software. If the software is modified by someone else and passed on, we want its recipients to know that what they have is not the original, so that any problems introduced by others will not reflect on the original authors reputations. Finally, any free program is threatened constantly by software patents. We wish to avoid the danger that redistributors of a free program will individually obtain patent licenses, in effect making the program proprietary. To prevent this,

we have made it clear that any patent must be licensed for everyones free use or not licensed at all. The precise terms and conditions for copying, distribution and modification follow.

TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND MODIFICATION 0. This License applies to any program or

other work which contains a notice placed by the copyright holder saying it may be distributed under the terms of this General Public License. The Program, below, refers to any such program or work, and a work based on the Program means either the Program or any derivative work under copyright law: that is to say, a work containing the Program or a portion of it, either verbatim or with modifications and/or translated into another language. (Hereinafter, translation is included without limitation in the term modification.) Each licensee is addressed as you. Activities other than copying, distribution and modification are not covered by this License; they are outside its scope. The act of running the Program is not restricted, and the output from the Program is covered only if its contents constitute a work based on the Program (independent of having been made by running the Program). Whether that is true depends on what the Program does.

1. You may copy and distribute verbatim copies of the Programs source code as you receive it, in any medium, provided that you conspicuously and appropriately publish on each copy an appropriate copyright notice and disclaimer of warranty; keep intact all the notices that refer to this License and to the absence of any warranty; and give any other recipients of the Program a copy of this License along with the Program. You may charge a fee for the physical act of transferring a copy, and you may at your option offer warranty protection in exchange for a fee.

2. You may modify your copy or copies of the Program or any portion of it, thus forming a work based on the Program, and copy and distribute such modifications or work under the terms of Section 1 above, provided that you also meet all of these conditions: a) You must cause the modified files to

carry prominent notices stating that you changed the files and the date of any change.

b) You must cause any work that you distribute or publish, that in whole or in part contains or is derived from the Program or any part thereof, to be licensed as a whole at no charge to all third parties under the terms of this License.

c) If the modified program normally reads commands interactively when run, you must cause it, when started running for such interactive use in the most ordinary way, to print or display an announcement including an appropriate copyright notice and a notice that there is no warranty (or else, saying that you provide a warranty) and that users may redistribute the program under these conditions, and telling the user how to view a copy of this License.

(Exception: if the Program itself is interactive but does not normally print such an announcement, your work based on the Program is not required to print an announcement.) These requirements apply to the modified work as a whole. If identifiable sections of that work are not derived from the Program, and can be reasonably considered independent and separate works in themselves, then this License, and its terms, do not apply to those sections when you distribute them as separate works. But when you distribute the same sections as part of a whole which is a work based on the

Program, the distribution of the whole must be on the terms of this License, whose permissions for other licensees extend to the entire whole, and thus to each and every part regardless of who wrote it. Thus, it is not the intent of this section to claim rights or contest your rights to work written entirely by you; rather, the intent is to exercise the right to control the distribution of derivative or collective works based on the Program. In addition, mere aggregation of another work not based on the Program with the Program (or with a work based on the Program) on a volume of a storage or distribution medium does not bring the other work under the scope of this License.

3. You may copy and distribute the Program (or a work based on it, under Section 2) in object code or executable form under the terms of Sections 1 and 2 above provided that you also do one of the following: a) Accompany it with the complete

corresponding machine-readable source code, which must be distributed under the terms of Sections 1 and 2 above on a medium customarily used for software interchange; or,

b) Accompany it with a written offer, valid for at least three years, to give any third party, for a charge no more than your cost of physically performing source distribution, a complete machine-readable copy of the corresponding source code, to be distributed under the terms of Sections 1 and 2 above on a medium customarily used for software interchange; or,

c) Accompany it with the information you received as to the offer to distribute corresponding source code. (This alternative is allowed only for noncommercial distribution and only if you received the program in object code or executable form with such an offer, in accord with Subsection b above.)

The source code for a work means the preferred form of the work for making modifications to it. For an executable work, complete source code means all the source code for all modules it contains, plus any associated interface definition files, plus the scripts used to control compilation and installation of the executable. However, as a special exception, the source code distributed need not include anything that is normally distributed (in either source or binary form) with the major components (compiler, kernel, and so on) of the operating system on which the executable runs, unless that component itself accompanies the executable. If distribution of executable or object code is made by offering access to copy from a designated place, then offering equivalent access to copy the source code from the same place counts as distribution of the source code, even though third parties are not compelled to copy the source along with the object code.

4. You may not copy, modify, sublicense, or distribute the Program except as expressly provided under this License. Any attempt otherwise to copy, modify, sublicense or distribute the Program is void, and will automatically terminate your rights under this License. However, parties who have received copies, or rights, from you under this License will not have their licenses terminated so long as such parties remain in full compliance.

5. You are not required to accept this License, since you have not signed it. However, nothing else grants you permission to modify or distribute the Program or its derivative works. These actions are prohibited by law if you do not accept this License. Therefore, by modifying or distributing the Program (or any work based

Additional Inform ation

ntinued

on the Program), you indicate your acceptance of this License to do so, and all its terms and conditions for copying, distributing or modifying the Program or works based on it.

6. Each time you redistribute the Program (or any work based on the Program), the recipient automatically receives a license from the original licensor to copy, distribute or modify the Program subject to these terms and conditions. You may not impose any further restrictions on the recipients exercise of the rights granted herein. You are not responsible for enforcing compliance by third parties to this License.

7. If, as a consequence of a court judgment or allegation of patent infringement or for any other reason (not limited to patent issues), conditions are imposed on you (whether by court order, agreement or otherwise) that contradict the conditions of this License, they do not excuse you from the conditions of this License. If you cannot distribute so as to satisfy simultaneously your obligations under this License and any other pertinent obligations, then as a consequence you may not distribute the Program at all. For example, if a patent license would not permit royalty-free redistribution of the Program by all those who receive copies directly or indirectly through you, then the only way you could satisfy both it and this License would be to refrain entirely from distribution of the Program. If any portion of this section is held invalid or unenforceable under any particular circumstance, the balance of the section is intended to apply and the section as a whole is intended to apply in other circumstances. It is not the purpose of this section to induce you to infringe any patents or other property right claims or to contest validity of any such claims; this section has the sole purpose of protecting the integrity of the free software distribution system, which is implemented by public license practices. Many people have made generous contributions to the wide range of software distributed through that system in reliance on consistent application of that system; it is up to the author/donor to decide if he or she is willing to distribute software through any other system and a licensee cannot impose that choice. This section is intended to make thoroughly clear what is believed to be a consequence of the rest of this License.

8. If the distribution and/or use of the Program is restricted in certain countries either by patents or by copyrighted interfaces, the original copyright holder who places the Program under this License may add an explicit geographical distribution limitation excluding those countries, so that distribution is permitted only in or among countries not thus excluded. In such case, this License incorporates the limitation as if written in the body of this License.

9. The Free Software Foundation may publish revised and/or new versions of the General Public License from time to time. Such new versions will be similar in spirit to the present version, but may differ in detail to address new problems or concerns. Each version is given a distinguishing version number. If the Program specifies a version number of this License which applies to it and any later version, you have the option of following the terms and conditions either of that version or of any later version published by the Free Software Foundation. If the Program does not specify a version number of this License, you may choose any version ever published by the Free Software Foundation.

10. If you wish to incorporate parts of the Program into other free programs whose distribution conditions are different, write to the author to ask for permission. For software which is copyrighted by the Free

Software Foundation, write to the Free Software Foundation; we sometimes make exceptions for this. Our decision will be guided by the two goals of preserving the free status of all derivatives of our free software and of promoting the sharing and reuse of software generally.

NO WARRANTY 11. BECAUSE THE PROGRAM IS

LICENSED FREE OF CHARGE, THERE IS NO WARRANTY FOR THE PROGRAM, TO THE EXTENT PERMITTED BYAPPLICABLE LAW. EXCEPT WHEN OTHERWISE STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR OTHER PARTIES PROVIDE THEPROGRAM AS IS WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE PROGRAM IS WITH YOU. SHOULD THE PROGRAM PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY SERVICING, REPAIROR CORRECTION.

12. IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER, OR ANY OTHER PARTY WHOMAY MODIFY AND/OR REDISTRIBUTE THE PROGRAM AS PERMITTED ABOVE, BE LIABLE TO YOU FOR DAMAGES, INCLUDING ANY GENERAL,SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE PROGRAM (INCLUDING BUT NOT LIMITED TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OF THE PROGRAM TO OPERATE WITH ANY OTHER PROGRAMS), EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

END OF TERMS AND CONDITIONS How to Apply These Terms to Your New Programs If you develop a new program, and you want it to be of the greatest possible use to the public, the best way to achieve this is to make it free software which everyone can redistribute and change under these terms. To do so, attach the following notices to the program. It is safest to attach them to the start of each source file to most effectively convey the exclusion of warranty; and each file should have at least the copyright line and a pointer to where the full notice is found.

Copyright (C) yyyy name of author

This program is free software; you can redistribute it and/or modify it under the terms of the GNU General Public License as published by the Free Software Foundation; either version 2 of the License, or (at your option) any later version. This program is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for more details. You should have received a copy of the GNU General Public License along with this program; if not, write to the Free Software Foundation, Inc., 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA. Also add information on how to contact you by electronic and paper mail.

If the program is interactive, make it output a short notice like this when it starts in an interactive mode:

Gnomovision version 69, Copyright (C) year name of author Gnomovision comes with ABSOLUTELY NO WARRANTY; for details type show w. This is free software, and you are welcome to redistribute it under certain conditions; type show c for details.

The hypothetical commands show w and show c should show the appropriate parts of the General Public License. Of course, the commands you use may be called something other than show w and show c; they could even be mouse-clicks or menu items-whatever suits your program. You should also get your employer (if you work as a programmer) or your school, if any, to sign a copyright disclaimer for the program, if necessary. Here is a sample; alter the names: Yoyodyne, Inc., hereby disclaims all copyright interest in the program Gnomovision (which makes passes at compilers) written by James Hacker.

signature of Ty Coon, 1 April 1989 Ty Coon, President of Vice

This General Public License does not permit incorporating your program into proprietary programs. If your program is a subroutine library, you may consider it more useful to permit linking proprietary applications with the library. If this is what you want to do, use the GNU Lesser General Public License instead of this License.

GNU Lesser General Public License Version 2.1, February 1999 Copyright (C) 1991, 1999 Free Software Foundation, Inc. 59 Temple Place, Suite 330, Boston, MA 02111- 1307, USA Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed. [This is the first released version of the Lesser GPL. It also counts as the successor of the GNU Library Public License, version 2, hence the version number2.1.]

Preamble The licenses for most software are designed to take away your freedom to share and change it. By contrast, the GNU General Public Licenses are intended to guarantee your freedom to share and change free software-to make sure the software is free for all its users. This license, the Lesser General Public License, applies to some specially designated software packages-typically libraries-of the Free Software Foundation and other authors who decide to use it. You can use it too, but we suggest you first think carefully about whether this license or the ordinary General Public License is the better strategy to use in any particular case, based on the explanations below. When we speak of free software, we are referring to freedom of use, not price. Our General Public Licenses are designed to make sure that you have the freedom to distribute copies of free software (and charge for this service if you wish); that you receive source code or can get it if you want it; that you can change the software and use pieces of it in new free programs; and that you are informed that you can do these things. To protect your rights, we need to make restrictions that forbid distributors to deny you these rights or to ask you to surrender these rights. These restrictions translate to certain responsibilities for you if you distribute copies of the library or if you modify it. For example, if you distribute copies of the library, whether gratis or for a fee, you must give the recipients all the rights that we gave you. You must make sure that they, too, receive or can get the source code. If you link other code with the library, you must provide complete object files to the recipients, so that they can relink them with the library after making changes to the library

,co

61

62

and recompiling it. And you must show them these terms so they know their rights. We protect your rights with a two-step method: (1) we copyright the library, and (2) we offer you this license, which gives you legal permission to copy, distribute and/or modify the library. To protect each distributor, we want to make it very clear that there is no warranty for the free library. Also, if the library is modified by someone else and passed on, the recipients should know that what they have is not the original version, so that the original authors reputation will not be affected by problems that might be introduced by others. Finally, software patents pose a constant threat to the existence of any free program. We wish to make sure that a company cannot effectively restrict the users of a free program by obtaining a restrictive license from a patent holder. Therefore, we insist that any patent license obtained for a version of the library must be consistent with the full freedom of use specified in this license. Most GNU software, including some libraries, is covered by the ordinary GNU General Public License. This license, the GNU Lesser General Public License, applies to certain designated libraries, and is quite different from the ordinary General Public License. We use this license for certain libraries in order to permit linking those libraries into non-free programs. When a program is linked with a library, whether statically or using a shared library, the combination of the two is legally speaking a combined work, a derivative of the original library. The ordinary General Public License therefore permits such linking only if the entire combination fits its criteria of freedom. The Lesser General Public License permits more lax criteria for linking other code with the library. We call this license the Lesser General Public License because it does Less to protect the users freedom than the ordinary General Public License. It also provides other free software developers Less of an advantage over competing non-free programs. These disadvantages are the reason we use the ordinary General Public License for many libraries. However, the Lesser license provides advantages in certain special circumstances. For example, on rare occasions, there may be a special need to encourage the widest possible use of a certain library, so that it becomes a de facto standard. To achieve this, non-free programs must be allowed to use the library. A more frequent case is that a free library does the same job as widely used non-free libraries. In this case, there is little to gain by limiting the free library to free software only, so we use the Lesser General Public License. In other cases, permission to use a particular library in non-free programs enables a greater number of people to use a large body of free software. For example, permission to use the GNU C Library in non-free programs enables many more people to use the whole GNU operating system, as well as its variant, the GNU/ Linux operating system. Although the Lesser General Public License is Less protective of the users freedom, it does ensure that the user of a program that is linked with the Library has the freedom and the wherewithal to run that program using a modified version of the Library. The precise terms and conditions for copying, distribution and modification follow. Pay close attention to the difference between a work based on the library and a work that uses the library. The former contains code derived from the library, whereas the latter must be combined with the library in order to run.

TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND MODIFICATION 0. This License Agreement applies to any

software library or other program which contains a notice placed by the copyright holder or other authorized party saying it may be distributed under the terms of this Lesser General Public License (also called

this License). Each licensee is addressed as you. A library means a collection of software functions and/or data prepared so as to be conveniently linked with application programs (which use some of those functions and data) to form executables. The Library, below, refers to any such software library or work which has been distributed under these terms. A work based on the Library means either the Library or any derivative work under copyright law: that is to say, a work containing the Library or a portion of it, either verbatim or with modifications and/or translated straightforwardly into another language. (Hereinafter, translation is included without limitation in the term modification.) Source code for a work means the preferred form of the work for making modifications to it. For a library, complete source code means all the source code for all modules it contains, plus any associated interface definition files, plus the scripts used to control compilation and installation of the library. Activities other than copying, distribution and modification are not covered by this License; they are outside its scope. The act of running a program using the Library is not restricted, and output from such a program is covered only if its contents constitute a work based on the Library (independent of the use of the Library in a tool for writing it). Whether that is true depends on what the Library does and what the program that uses the Library does.

1. You may copy and distribute verbatim copies of the Librarys complete source code as you receive it, in any medium, provided that you conspicuously and appropriately publish on each copy an appropriate copyright notice and disclaimer of warranty; keep intact all the notices that refer to this License and to the absence of any warranty; and distribute a copy of this License along with the Library. You may charge a fee for the physical act of transferring a copy, and you may at your option offer warranty protection in exchange for a fee.

2. You may modify your copy or copies of the Library or any portion of it, thus forming a work based on the Library, and copy and distribute such modifications or work under the terms of Section 1 above, provided that you also meet all of these conditions: a) The modified work must itself be a

software library. b) You must cause the files modified to

carry prominent notices stating that you changed the files and the date of any change.

c) You must cause the whole of the work to be licensed at no charge to all third parties under the terms of this License.

d) If a facility in the modified Library refers to a function or a table of data to be supplied by an application program that uses the facility, other than as an argument passed when the facility is invoked, then you must make a good faith effort to ensure that, in the event an application does not supply such function or table, the facility still operates, and performs whatever part of its purpose remains meaningful.

(For example, a function in a library to compute square roots has a purpose that is entirely well-defined independent of the application. Therefore, Subsection 2d requires that any application-supplied function or table used by this function must be optional: if the application does not supply it, the square root function must still compute square roots.) These requirements apply to the modified work as a whole. If identifiable sections of that work are not derived from the Library, and can be

reasonably considered independent and separate works in themselves, then this License, and its terms, do not apply to those sections when you distribute them as separate works. But when you distribute the same sections as part of a whole which is a work based on the Library, the distribution of the whole must be on the terms of this license, whose permissions for other licensees extend to the entire whole, and thus to each and every part regardless of who wrote it. Thus, it is not the intent of this section to claim rights or contest your rights to work written entirely by you; rather, the intent is to exercise the right to control the distribution of derivative or collective works based on the Library. In addition, mere aggregation of another work not based on the Library with the Library (or with a work based on the Library) on a volume of a storage or distribution medium does not bring the other work under the scope of this License.

3. You may opt to apply the terms of the ordinary GNU General Public License instead of this License to a given copy of the Library. To do this, you must alter all the notices that refer to this License, so that they refer to the ordinary GNU General Public License, version 2, instead of to this License. (If a newer version than version 2 of the ordinary GNU General Public License has appeared, then you can specify that version instead if you wish.) Do not make any other change in these notices. Once this change is made in a given copy, it is irreversible for that copy, so the ordinary GNU General Public License applies to all subsequent copies and derivative works made from that copy. This option is useful when you wish to copy part of the code of the Library into a program that is not a library.

4. You may copy and distribute the Library (or a portion or derivative of it, under Section 2) in object code or executable form under the terms of Sections1 and 2 above provided that you accompany it with the complete corresponding machine-readable source code, which must be distributed under the terms of Sections 1 and 2 above on a medium customarily used for software interchange. If distribution of object code is made by offering access to copy from a designated place, then offering equivalent access to copy the source code from the same place satisfies the requirement to distribute the source code, even though third parties are not compelled to copy the source along with the object code.

5. A program that contains no derivative of any portion of the Library, but is designed to work with the Library by being compiled or linked with it, is called a work that uses the Library. Such a work, in isolation, is not a derivative work of the Library, and therefore falls outside the scope of this License. However, linking a work that uses the Library with the Library creates an executable that is a derivative of the Library (because it contains portions of the Library), rather than a work that uses the library. The executable is therefore covered by this License. Section 6 states terms for distribution of such executables. When a work that uses the Library uses material from a header file that is part of the Library, the object code for the work may be a derivative work of the Library even though the source code is not. Whether this is true is especially significant if the work can be linked without the Library, or if the work is itself a library. The threshold for this to be true is not precisely defined by law. If such an object file uses only numerical parameters, data structure layouts and accessors, and small macros and small inline functions (ten lines or less in length),

Additional Inform ation

ntinued

then the use of the object file is unrestricted, regardless of whether it is legally a derivative work. (Executables containing this object code plus portions of the Library will still fall under Section 6.) Otherwise, if the work is a derivative of the Library, you may distribute the object code for the work under the terms of Section 6. Any executables containing that work also fall under Section 6, whether or not they are linked directly with the Library itself.

6. As an exception to the Sections above, you may also combine or link a work that uses the Library with the Library to produce a work containing portions of the Library, and distribute that work under terms of your choice, provided that the terms permit modification of the work for the customers own use and reverse engineering for debugging such modifications. You must give prominent notice with each copy of the work that the Library is used in it and that the Library and its use are covered by this License. You must supply a copy of this License. If the work during execution displays copyright notices, you must include the copyright notice for the Library among them, as well as a reference directing the user to the copy of this License. Also, you must do one of these things: a) Accompany the work with the

complete corresponding machine- readable source code for the Library including whatever changes were used in the work (which must be distributed under Sections 1 and 2 above); and, if the work is an executable linked with the Library, with the complete machine-readable work that uses the Library, as object code and/or source code, so that the user can modify the Library and then relink to produce a modified executable containing the modified Library. (It is understood that the user who changes the contents of definitions files in the Library will not necessarily be able to recompile the application to use the modified definitions.)

b) Use a suitable shared library mechanism for linking with the Library. A suitable mechanism is one that (1) uses at run time a copy of the library already present on the users computer system, rather than copying library functions into the executable, and (2) will operate properly with a modified version of the library, if the user installs one, as long as the modified version is interface- compatible with the version that the work was made with.

c) Accompany the work with a written offer, valid for at least three years, to give the same user the materials specified in Subsection 6a, above, for a charge no more than the cost of performing this distribution.

d) If distribution of the work is made by offering access to copy from a designated place, offer equivalent access to copy the above specified materials from the same place.

e) Verify that the user has already received a copy of these materials or that you have already sent this user a copy. For an executable, the required form of the work that uses the Library must include any data and utility programs needed for reproducing the executable from it. However, as a special exception, the materials to be distributed need not include anything that is normally distributed (in either source or binary form) with the major components (compiler, kernel, and so on) of the operating system on which the executable runs, unless that

component itself accompanies the executable. It may happen that this requirement contradicts the license restrictions of other proprietary libraries that do not normally accompany the operating system. Such a contradiction means you cannot use both them and the Library together in an executable that you distribute.

7. You may place library facilities that are a work based on the Library side-by-side in a single library together with other library facilities not covered by this License, and distribute such a combined library, provided that the separate distribution of the work based on the Library and of the other library facilities is otherwise permitted, and provided that you do these two things: a) Accompany the combined library with

a copy of the same work based on the Library, uncombined with any other library facilities. This must be distributed under the terms of the Sections above.

b) Give prominent notice with the combined library of the fact that part of it is a work based on the Library, and explaining where to find the accompanying uncombined form of the same work.

8. You may not copy, modify, sublicense, link with, or distribute the Library except as expressly provided under this License. Any attempt otherwise to copy, modify, sublicense, link with, or distribute the Library is void, and will automatically terminate your rights under this License. However, parties who have received copies, or rights, from you under this License will not have their licenses terminated so long as such parties remain in full compliance.

9. You are not required to accept this License, since you have not signed it. However, nothing else grants you permission to modify or distribute the Library or its derivative works. These actions are prohibited by law if you do not accept this License. Therefore, by modifying or distributing the Library(or any work based on the Library), you indicate your acceptance of this License to do so, and all its terms and conditions for copying, distributing or modifying the Library or works based on it.

10. Each time you redistribute the Library (or any work based on the Library), the recipient automatically receives a license from the original licensor to copy, distribute, link with or modify the Library subject to these terms and conditions. You may not impose any further restrictions on the recipients exercise of the rights granted herein. You are not responsible for enforcing compliance by third parties with this License.

11. If, as a consequence of a court judgment or allegation of patent infringement or for any other reason (not limited to patent issues), conditions are imposed on you (whether by court order, agreement or otherwise) that contradict the conditions of this License, they do not excuse you from the conditions of this License. If you cannot distribute so as to satisfy simultaneously your obligations under this License and any other pertinent obligations, then as a consequence you may not distribute the Library at all. For example, if a patent license would not permit royalty-free redistribution of the Library by all those who receive copies directly or indirectly through you, then the only way you could satisfy both it and this License would be to refrain entirely from distribution of the Library. If any portion of this section is held invalid or unenforceable under any particular circumstance, the balance of the section is intended to apply, and the section as a whole is intended to apply in other circumstances.

It is not the purpose of this section to induce you to infringe any patents or other property right claims or to contest validity of any such claims; this section has the sole purpose of protecting the integrity of the free software distribution system which is implemented by public license practices. Many people have made generous contributions to the wide range of software distributed through that system in reliance on consistent application of that system; it is up to the author/donor to decide if he or she is willing to distribute software through any other system and a licensee cannot impose that choice. This section is intended to make thoroughly clear what is believed to be a consequence of the rest of this License.

12. If the distribution and/or use of the Library is restricted in certain countries either by patents or by copyrighted interfaces, the original copyright holder who places the Library under this License may add an explicit geographical distribution limitation excluding those countries, so that distribution is permitted only in or among countries not thus excluded. In such case, this License incorporates the limitation as if written in the body of this License.

13. The Free Software Foundation may publish revised and/or new versions of the Lesser General Public License from time to time. Such new versions will be similar in spirit to the present version, but may differ in detail to address new problems or concerns. Each version is given a distinguishing version number. If the Library specifies a version number of this License which applies to it and any later version, you have the option of following the terms and conditions either of that version or of any later version published by the Free Software Foundation. If the Library does not specify a license version number, you may choose any version ever published by the Free Software Foundation.

14. If you wish to incorporate parts of the Library into other free programs whose distribution conditions are incompatible with these, write to the author to ask for permission. For software which is copyrighted by the Free Software Foundation, write to the Free Software Foundation; we sometimes make exceptions for this. Our decision will be guided by the two goals of preserving the free status of all derivatives of our free software and of promoting the sharing and reuse of software generally.

NO WARRANTY 15. BECAUSE THE LIBRARY IS LICENSED

FREE OF CHARGE, THERE IS NO WARRANTY FOR THE LIBRARY, TO THE EXTENT PERMITTED BY APPLICABLE LAW. EXCEPT WHEN OTHERWISE STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR OTHER PARTIES PROVIDE THE LIBRARY AS IS WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIESOF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THELIBRARY IS WITH YOU. SHOULD THE LIBRARY PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY SERVICING, REPAIR OR CORRECTION.

16. IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER, OR ANY OTHER PARTY WHOMAY MODIFY AND/OR REDISTRIBUTE THE LIBRARY AS PERMITTED ABOVE, BE LIABLE TO YOU FOR DAMAGES, INCLUDING

,co

63

64

ANY GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE LIBRARY (INCLUDING BUT NOTLIMITED TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OFTHE LIBRARY TO OPERATE WITH ANY OTHER SOFTWARE), EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

END OF TERMS AND CONDITIONS

How to Apply These Terms to Your New Libraries If you develop a new library, and you want it to be of the greatest possible use to the public, we recommend making it free software that everyone can redistribute and change. You can do so by permitting redistribution under these terms (or, alternatively, under the terms of the ordinary General Public License). To apply these terms, attach the following notices to the library. It is safest to attach them to the start of each source file to most effectively convey the exclusion of warranty; and each file should have at least the copyright line and a pointer to where the full notice is found.

Copyright (C) year name of author

This library is free software; you can redistribute it and/or modify it under the terms of the GNU Lesser General Public License as published by the Free Software Foundation; either version 2.1 of the License, or (at your option) any later version. This library is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU Lesser General Public License for more details. You should have received a copy of the GNU Lesser General Public License along with this library; if not, write to the Free Software Foundation, Inc., 59Temple Place, Suite 330, Boston, MA 02111-1307, USA Also add information on how to contact you by electronic and paper mail. You should also get your employer (if you work as a programmer) or your school, if any, to sign a copyright disclaimer for the library, if necessary. Here is a sample; alter the names: Yoyodyne, Inc., hereby disclaims all copyright interest in the library Frob (a library for tweaking knobs) written by James Random Hacker. signature of Ty Coon, 1 April 1990 Ty Coon, President of Vice Thats all there is to it!

OpenSSL License OpenSSL Copyright (c) 1998-2004 The OpenSSL Project. All rights reserved.

Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: 1. Redistributions of source code must retain

the above copyright notice, this list of conditions and the following disclaimer.

2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.

3. All advertising materials mentioning features or use of this software must display the following acknowledgment: This product includes software developed by the OpenSSL Project for use in the OpenSSL Toolkit. (http://www.openssl.org/)

4. The names OpenSSL Toolkit and OpenSSL Project must not be used to endorse or promote products derived from this software without prior written permission. For written permission, please contact opensslcore@openssl.org.

5. Products derived from this software may not be called OpenSSL nor may OpenSSL appear in their names without prior written permission of the OpenSSL Project.

6. Redistributions of any form whatsoever must retain the following acknowledgment: This product includes software developed by the OpenSSL Project for use in the OpenSSL Toolkit (http://www.openssl.org/)

THIS SOFTWARE IS PROVIDED BY THE OpenSSL PROJECT AS IS AND ANY EXPRESSED OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE OpenSSL PROJECT OR ITS CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.

This product includes cryptographic software written by Eric Young (eay@cryptsoft.com). This product includes software written by Tim Hudson (tjh@cryptsoft.com).

Original SSLeay License Original SSLeay Copyright (C) 1995-1998 Eric Young (eay@cryptsoft.com) All rights reserved.

This package is an SSL implementation written by Eric Young (eay@cryptsoft.com). The implementation was written so as to conform with Netscapes SSL.

This library is free for commercial and non- commercial use as long as the following conditions are aheared to. The following conditions apply to all code found in this distribution, be it the RC4, RSA, lhash, DES, etc., code; not just the SSL code. The SSL documentation included with this distribution is covered by the same copyright terms except that the holder is Tim Hudson (tjh@cryptsoft.com).

Copyright remains Eric Young's, and as such any Copyright notices in the code are not to be removed. If this package is used in a product, Eric Young should be given attribution as the author of the parts of the library used. This can be in the form of a textual message at program startup or in documentation (online or textual) provided with the package.

Redistribution and use in source and binary forms, with or without modification, are

permitted provided that the following conditions are met: 1. Redistributions of source code must retain

the copyright notice, this list of conditions and the following disclaimer.

2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.

3. All advertising materials mentioning features or use of this software must display the following acknowledgement: This product includes cryptographic software written by Eric Young (eay@cryptsoft.com) The word 'cryptographic' can be left out if the rouines from the library being used are not cryptographic related :-).

4. If you include any Windows specific code (or a derivative thereof) from the apps directory (application code) you must include an acknowledgement: This product includes software written by Tim Hudson (tjh@cryptsoft.com)

THIS SOFTWARE IS PROVIDED BY ERIC YOUNG ``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.

The licence and distribution terms for any publically available version or derivative of this code cannot be changed. i.e. this code cannot simply be copied and put under another distribution licence [including the GNU Public Licence.]

FreeType The FreeType Project is copyright (C) 1996- 2000 by David Turner, Robert Wilhelm, and Werner Lemberg. All rights reserved except as specified below.

THE FREETYPE PROJECT IS PROVIDED AS IS WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT WILL ANY OF THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY DAMAGES CAUSED BY THE USE OR THE INABILITY TO USE, OF THE FREETYPE PROJECT.

Howl Copyright (c) 2003, 2004 Porchdog Software All rights reserved.

THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS AS IS AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE

Additional Inform ation

DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.

jpeg-6b If only executable code is distributed, then the accompanying documentation must state that this software is based in part on the work of the Independent JPEG Group.

libpng COPYRIGHT NOTICE, DISCLAIMER, and LICENSE:

If you modify libpng you may insert additional notices immediately following this sentence.

libpng version 1.2.6, December 3, 2004, is Copyright (c) 2004 Glenn Randers-Pehrson, and is distributed according to the same disclaimer and license as libpng-1.2.5 with the following individual added to the list of Contributing Authors

Cosmin Truta

libpng versions 1.0.7, July 1, 2000, through 1.2.5 - October 3, 2002, are Copyright (c) 2000-2002 Glenn Randers-Pehrson, and are distributed according to the same disclaimer and license as libpng-1.0.6 with the following individuals added to the list of Contributing Authors

Simon-Pierre Cadieux Eric S. Raymond Gilles Vollant

and with the following additions to the disclaimer:

There is no warranty against interference with your enjoyment of the library or against infringement. There is no warranty that our efforts or the library will fulfill any of your particular purposes or needs. This library is provided with all faults, and the entire risk of satisfactory quality, performance, accuracy, and effort is with the user.

libpng versions 0.97, January 1998, through 1.0.6, March 20, 2000, are Copyright (c) 1998, 1999 Glenn Randers-Pehrson, and are distributed according to the same disclaimer and license as libpng-0.96, with the following individuals added to the list of Contributing Authors:

Tom Lane Glenn Randers-Pehrson Willem van Schaik

libpng versions 0.89, June 1996, through 0.96, May 1997, are Copyright (c) 1996, 1997 Andreas Dilger Distributed according to the same disclaimer and license as libpng-0.88, with the following individuals added to the list of Contributing Authors:

John Bowler Kevin Bracey Sam Bushell Magnus Holmgren Greg Roelofs Tom Tanner

libpng versions 0.5, May 1995, through 0.88, January 1996, are Copyright (c) 1995, 1996 Guy Eric Schalnat, Group 42, Inc.

For the purposes of this copyright and license, Contributing Authors is defined as the following set of individuals:

Andreas Dilger Dave Martindale Guy Eric Schalnat Paul Schmidt Tim Wegner

The PNG Reference Library is supplied AS IS. The Contributing Authors and Group 42, Inc. disclaim all warranties, expressed or implied, including, without limitation, the warranties of merchantability and of fitness for any purpose. The Contributing Authors and Group 42, Inc. assume no liability for direct, indirect, incidental, special, exemplary, or consequential damages, which may result from the use of the PNG Reference Library, even if advised of the possibility of such damage.

Permission is hereby granted to use, copy, modify, and distribute this source code, or portions hereof, for any purpose, without fee, subject to the following restrictions:

1. The origin of this source code must not be misrepresented.

2. Altered versions must be plainly marked as such and must not be misrepresented as being the original source.

3. This Copyright notice may not be removed or altered from any source or altered source distribution.

The Contributing Authors and Group 42, Inc. specifically permit, without fee, and encourage the use of this source code as a component to supporting the PNG file format in commercial products. If you use this source code in a product, acknowledgment is not required but would be appreciated.

A png_get_copyright function is available, for convenient use in about boxes and the like:

printf(%s,png_get_copyright(NULL));

Also, the PNG logo (in PNG format, of course) is supplied in the files pngbar.png and pngbar.jpg (88x31) and pngnow.png (98x31).

Libpng is OSI Certified Open Source Software. OSI Certified Open Source is a certification mark of the Open Source Initiative.

Glenn Randers-Pehrson glennrp at users.sourceforge.net December 3, 2004

Libungif The GIFLIB distribution is Copyright (c) 1997 Eric S. Raymond

THE SOFTWARE IS PROVIDED AS IS, WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.

Luxi font Bigelow & Holmes Inc and URW++ GmbH Luxi font license

Luxi fonts copyright (c) 2001 by Bigelow & Holmes Inc. Luxi font instruction code copyright (c) 2001 by URW++ GmbH. All Rights Reserved. Luxi is a registered trademark of Bigelow & Holmes Inc.

THE FONT SOFTWARE IS PROVIDED AS IS, WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OF COPYRIGHT, PATENT, TRADEMARK, OR OTHER RIGHT. IN NO EVENT SHALL BIGELOW & HOLMES INC. OR URW++ GMBH. BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, INCLUDING ANY GENERAL, SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF THE USE OR INABILITY TO USE THE FONT SOFTWARE OR FROM OTHER DEALINGS IN THE FONT SOFTWARE.

TIFF Copyright (c) 1988-1997 Sam Leffler Copyright (c) 1991-1997 Silicon Graphics, Inc.

THE SOFTWARE IS PROVIDED AS-IS AND WITHOUT WARRANTY OF ANY KIND, EXPRESS, IMPLIED OR OTHERWISE, INCLUDING WITHOUT LIMITATION, ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.

IN NO EVENT SHALL SAM LEFFLER OR SILICON GRAPHICS BE LIABLE FOR ANY SPECIAL, INCIDENTAL, INDIRECT OR CONSEQUENTIAL DAMAGES OF ANY KIND, OR ANY DAMAGES WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER OR NOT ADVISED OF THE POSSIBILITY OF DAMAGE, AND ON ANY THEORY OF LIABILITY, ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.

This software is based in part on zlib see http:// www.zlib.net for information.

This software is based in part on Mozilla Public License 1.1 see http://www.mozilla.org/MPL/ for information.

This software is based in part on Apple Public Source License or the reciient's rights thereunder see http://developer.apple.com/ for information.

This software is based in part on Intel License see http://www.intel.com/ for information.

TinyLogin This software is copyright 1988 - 1994, Julianne Frances Haugh. All rights reserved.

The shadow utilities license This software is copyright 1988 - 1994, Julianne Frances Haugh. All rights reserved.

Vera.ttf/VeraMono.ttf Copyright 2003 by Bitstream, Inc. All Rights Reserved. Bitstream Vera SansBitstreamVeraSans-RomanRelease 1.10 Copyright 2003 by Bitstream, Inc. All Rights Reserved. Bitstream Vera is a trademark of Bitstream, Inc.

65

66

Glossary

AACS Advanced Access Content System is a specification for managing digital entertainment contents stored on the next generation of prerecorded and recorded optical media. The specification enables consumers to enjoy digital entertainment content, including high-definition content.

AVCHD (page 6) The AVCHD format is a high definition digital video camera format used to record SD (standard definition) or HD (high definition) signals of either the 1080i specification*1 or the 720p specification*2 on DVDs, using efficient data compression coding technology. The MPEG-4 AVC/H.264 format is adopted to compress video data, and the Dolby Digital or Linear PCM is used to compress audio data. The MPEG-4 AVC/H.264 format is capable of compressing images at higher efficiency than that of the conventional image compression format. The MPEG-4 AVC/ H.264 format enables a high definition (HD) video signal shot on a digital video camera recorder to be recorded on DVDs in the same way as for a standard definition (SD) television signal. *1 A high definition specification that

utilizes1080 effective scanning lines and the interlace format.

*2 A high definition specification that utilizes 720 effective scanning lines and the progressive format.

BD-J application The BD-ROM format supports Java for interactive functions. BD-J offers content providers almost unlimited functionality when creating interactive BD-ROM titles.

BD-R (page 5) BD-R (Blu-ray Disc Recordable) is a recordable, write-once Blu-ray Disc, available in the same capacities as the BD below. Since contents can be recorded and cannot be overwritten, a BD-R can be used to archive valuable data or storing and distributing video material.

BD-RE (page 5) BD-RE (Blu-ray Disc Rewritable) is a recordable and rewritable Blu-ray Disc, available in the same capacities as the BD below. The re-recordable feature makes extensive editing and time- shifting applications possible.

BD-ROM (page 5) BD-ROMs (Blu-ray Disc Read-Only Memory) are commercially produced discs and are available in the same capacities as the BD below. Other than conventional movie and video contents, these discs have enhanced features such as interactive content, menu operations using pop-up menus (see below), selection of subtitle display, and slideshow. Although a BD-ROM may contain any form of data, most BD ROM discs will contain movies in High Definition format, for playback on Blu- ray Disc players.

Blu-ray Disc (BD) (page 5) A disc format developed for recording/ playing high-definition (HD) video (for HDTV, etc.), and for storing large amounts of data. A single layer Blu-ray Disc holds up to 25 GB, and a dual-layer Blu-ray Disc holds up to 50 GB of data.

Chapter (page 25) Sections of a picture or a music feature that are smaller than titles. A title is composed of several chapters. Depending on the disc, no chapters may be recorded.

Dolby Digital (page 47) Digital audio compression technology developed by Dolby Laboratories. This technology conforms to multi-channel surround sound. The rear channel is stereo and there is a discrete subwoofer channel in this format. Dolby Digital provides the same discrete channels of high quality digital audio found in Dolby Digital theater surround sound systems. Good channel separation is realized because all of the channel data is recorded discretely and little deterioration occurs because all channel data processing is digital.

Dolby Digital Plus (page 48) Developed as an extension to Dolby Digital, the audio coding technology supports 7.1 multi-channel surround sound.

Dolby Surround (Pro Logic) (page 47) Audio signal processing technology that Dolby Laboratories developed for surround sound. When the input signal contains a surround component, the Pro Logic process outputs the front, center and rear signals. The rear channel is monaural.

Dolby TrueHD (page 48) Dolby TrueHD is a lossless coding technology that supports up to 8 channels of multi-channel surround sound for the next generation optical discs. The reproduced sound is true to the original source bit-for-bit.

DTS (page 47) Digital audio compression technology that DTS, Inc. developed. This technology conforms to multi-channel surround sound. The rear channel is stereo and there is a discrete subwoofer channel in this format. DTS provides the same discrete channels of high quality digital audio. Good channel separation is realized because all of the channel data is recorded discretely and little deterioration occurs because all channel data processing is digital.

DTS-HD (page 48) DTS-HD is an extended format of the Coherent Acoustics audio coding system, which also encompasses DTS Digital Surround, DTS-ES, and DTS 96/ 24. DTS-HD is highly flexible in supporting the number of discrete surround sound channels. While 7.1ch surround sound is planned for Blu-ray Discs, the audio signals can be downmixed to 5.1 or 2 channels for backward compatibility, and the reproduced audio quality can either be at the bit rate of DTS Digital Surround or the lossless mode.

DVD VIDEO (page 5) A disc format that contains up to eight hours of moving pictures on a disc the same diameter as a CD. A single-layer single sided DVD holds up to 4.7 GB; a double layer single-sided DVD, 8.5 GB; a single layer double-sided DVD, 9.4 GB; double-layer double-sided DVD, 17 GB. The MPEG 2 format is adopted for the efficient video data compression. The variable rate coding technology that changes the data to be allocated according to the status of the picture is adopted for reproducing high-quality pictures. Audio information is recorded in a multi-channel format, such as Dolby Digital, allowing for a realistic audio presence.

Additional Inform ation

DVD-R (page 5) A DVD-R is a recordable disc that is the same size as a DVD VIDEO. Contents can be recorded only once to a DVD-R, and will have the same format as a DVD VIDEO. The DVD-R has two different modes: VR mode and Video mode. DVDs created in Video mode have the same format as a DVD VIDEO, while discs created in VR (Video Recording) mode allow the contents to be programmed or edited.

DVD-RW (page 5) A DVD-RW is a recordable and rewritable disc that is the same size as a DVD VIDEO. The DVD-RW has two different modes: VR mode and Video mode. DVDs created in Video mode have the same format as a DVD VIDEO, while discs created in VR (Video Recording) mode allow the contents to be programmed or edited.

DVD+R (page 5) A DVD+R (read plus R) is a recordable disc that is the same size as a DVD VIDEO. Contents can be recorded only once to a DVD+R, and will have the same format as a DVD VIDEO.

DVD+RW (page 5) A DVD+RW (read plus RW) is a recordable and rewritable disc. DVD+RWs use a recording format that is comparable to the DVD VIDEO format.

Film-based software, Video-based software DVDs can be classified as Film-based or Video-based software. Film-based DVDs contain the same images (24 frames per second) that are shown at movie theaters. Video-based DVDs, such as television dramas or sitcoms, display images at 30 frames (or 60 fields) per second.

HDMI (High-Definition Multimedia Interface) HDMI is an interface that supports both video and audio on a single digital connection. The HDMI connection carries standard to high definition video signals and multi-channel audio signals to AV components such as HDMI equipped TVs, in digital form without degradation. The HDMI specification supports HDCP (High-bandwidth Digital Contents Protection), a copy protection technology for digital entertainment contents for HDMI.

Interlace format Interlace format shows every other line of an image as a single field and is the standard method for displaying images on television. The even number field shows the even numbered lines of an image, and the odd numbered field shows the odd numbered lines of an image.

MPEG-2 One of the video data compression schemes established by the Moving Picture Experts Group (MPEG), which is adopted for DVD VIDEOs and digital broadcasts worldwide. The scheme specifies MPEG-2 PS (Program Stream) for recordable media such as a DVD VIDEO, and MPEG-2 TS (Transport Stream) for digital broadcasts and other communications.

Pop-up menu An enhanced menu operation available on BD-ROMs. The pop-up menu appears when MENU is pressed during playback, and can be operated while playback is in progress.

Progressive format Compared to the Interlace format that alternately shows every other line of an image (field) to create one frame, the Progressive format shows the entire image at once as a single frame. This means that while the Interlace format can show 30 frames/60 fields in one second, the Progressive format can show 60 frames in one second. The overall picture quality increases and still images, text, and horizontal lines appear sharper.

Title (page 26) The longest section of a picture or music feature on a DVD, movie, etc., in video software, or the entire album in audio software.

x.v.Color (page 8) x.v.Color is a more familiar term for the xvYCC standard proposed by Sony, and is a trademark of Sony. xvYCC is an international standard for color space in video. This standard can express a wider color range than the currently used broadcast standard.

Specifications

System Laser: Semiconductor laser

Outputs (Jack name: Jack type/Output level/ Load impedance) AUDIO OUT L/R:

Phono jack/2 Vrms/10 kilohms DIGITAL OUT (OPTICAL):

Optical output jack/18 dBm (wave length 660 nm)

DIGITAL OUT (COAXIAL): Phono jack/0.5 Vp-p/75 ohms

5.1CH OUTPUT: Phono jack/2 Vrms/10 kilohms

HDMI OUT: HDMI 19-pin standard connector

COMPONENT VIDEO OUT(Y, PB, PR):

Phono jack/Y: 1.0 Vp-p/PB, PR: progressive or interlace = 0.7 Vp-p/75 ohms

VIDEO: Phono jack/1.0 Vp-p/75 ohms S VIDEO: 4-pin mini DIN/Y:

1.0 Vp-p, C: 0.286 Vp-p/75 ohms

General Power requirements:

120 V AC, 60 Hz Power consumption: 33 W Dimensions (approx.):

430 79 375 mm (17 3 1/8 14 7/8 in.) (width/height/depth) incl. projecting parts

Mass (approx.): 4.5 kg (10 lb) Operating temperature:

5 C to 35 C (41F to 95F) Operating humidity:

25 % to 80 %

Supplied accessories See page 9.

Specifications and design are subject to change without notice.

67

68

Language Code List

For details, see page 49.

Language (abbr.) Code

Japanese (ja) 1001

English (en) 0514

French (fr) 0618

German (de) 0405

Italian (it) 0920

Spanish (es) 0519

Dutch (nl) 1412

Russian (ru) 1821

Chinese (zh) 2608

Korean (ko) 1115

Greek (el) 0512

Afar (aa) 0101

Abkhazian (ab) 0102

Afrikaans (af) 0106

Amharic (am) 0113

Arabic (ar) 0118

Assamese (as) 0119

Aymara (ay) 0125

Azerbaijani (az) 0126

Bashkir (ba) 0201

Byelorussian (be) 0205

Bulgarian (bg) 0207

Bihari (bh) 0208

Bislama (bi) 0209

Bengali (bn) 0214

Tibetan (bo) 0215

Breton (br) 0218

Catalan (ca) 0301

Corsican (co) 0315

Czech (cs) 0319

Welsh (cy) 0325

Danish (da) 0401

Bhutani (dz) 0426

Esperanto (eo) 0515

Estonian (et) 0520

Basque (eu) 0521

Persian (fa) 0601

Finnish (fi) 0609

Fiji (fj) 0610

Faroese (fo) 0615

Frisian (fy) 0625

Irish (ga) 0701

Scots-Gaelic (gd) 0704

Galician (gl) 0712

Guarani (gn) 0714

Gujarati (gu) 0721

Hausa (ha) 0801

Hindi (hi) 0809

Croatian (hr) 0818

Hungarian (hu) 0821

Armenian (hy) 0825

Interlingua (ia) 0901

Interlingue (ie) 0905

Inupiak (ik) 0911

Indonesian (in) 0914

Icelandic (is) 0919

Hebrew (iw) 0923

Yiddish (ji) 1009

Javanese (jw) 1023

Georgian (ka) 1101

Kazakh (kk) 1111

Greenlandic (kl) 1112

Cambodian (km) 1113

Kannada (kn) 1114

Kashmiri (ks) 1119

Kurdish (ku) 1121

Kirghiz (ky) 1125

Latin (la) 1201

Lingala (ln) 1214

Laothian (lo) 1215

Lithuanian (lt) 1220

Latvian (lv) 1222

Malagasy (mg) 1307

Maori (mi) 1309

Macedonian (mk) 1311

Malayalam (ml) 1312

Mongolian (mn) 1314

Moldavian (mo) 1315

Marathi (mr) 1318

Malay (ms) 1319

Maltese (mt) 1320

Burmese (my) 1325

Nauru (na) 1401

Nepali (ne) 1405

Norwegian (no) 1415

Occitan (oc) 1503

Oromo (om) 1513

Oriya (or) 1518

Panjabi (pa) 1601

Polish (pl) 1612

Pashto, Pushto (ps) 1619

Portuguese (pt) 1620

Quechua (qu) 1721

Rhaeto-Romance (rm) 1813

Kirundi (rn) 1814

Romanian (ro) 1815

Kinyarwanda (rw) 1823

Sanskrit (sa) 1901

Sindhi (sd) 1904

Sangho (sg) 1907

Serbo-Croatian (sh) 1908

Language (abbr.) Code

Sinhalese (si) 1909

Slovak (sk) 1911

Slovenian (sl) 1912

Samoan (sm) 1913

Shona (sn) 1914

Somali (so) 1915

Albanian (sq) 1917

Serbian (sr) 1918

Siswati (ss) 1919

Sesotho (st) 1920

Sundanese (su) 1921

Swedish (sv) 1922

Swahili (sw) 1923

Tamil (ta) 2001

Telugu (te) 2005

Tajik (tg) 2007

Thai (th) 2008

Tigrinya (ti) 2009

Turkmen (tk) 2011

Tagalog (tl) 2012

Setswana (tn) 2014

Tonga (to) 2015

Turkish (tr) 2018

Tsonga (ts) 2019

Tatar (tt) 2020

Twi (tw) 2023

Ukrainian (uk) 2111

Urdu (ur) 2118

Uzbek (uz) 2126

Vietnamese (vi) 2209

Volapk (vo) 2215

Wolof (wo) 2315

Xhosa (xh) 2408

Yoruba (yo) 2515

Zulu (zu) 2621

Language (abbr.) Code

Additional Inform ation

Parental Control Country/Area Code List

For details, see page 50.

Area (abbr.) Code

Argentina (ar) 0118

Australia (au) 0121

Austria (at) 0120

Belgium (be) 0205

Brazil (br) 0218

Canada (ca) 0301

Chile (cl) 0312

China (cn) 0314

Denmark (dk) 0411

Finland (fi) 0609

France (fr) 0618

Germany (de) 0405

Hong Kong (hk) 0811

India (in) 0914

Indonesia (id) 0904

Italy (it) 0920

Japan (jp) 1016

Korea, Republic of (kr) 1118

Malaysia (my) 1325

Mexico (mx) 1324

Netherlands (nl) 1412

New Zealand (nz) 1426

Norway (no) 1415

Pakistan (pk) 1611

Philippines (ph) 1608

Portugal (pt) 1620

Russian Federation (ru) 1821

Singapore (sg) 1907

Spain (es) 0519

Switzerland (ch) 0308

Sweden (se) 1905

Taiwan (tw) 2023

Thailand (th) 2008

United Kingdom (gb) 0702

United States of America (us)

2119

69

70

Index

Words in quotations appear in the on- screen displays.

Numerics 5.1CH OUTPUT 14, 51

A A/V Control 22 AACS 66 ANGLE 24 AUDIO 24 Audio Control 27 Audio Output Mode 51 Audio Setup 47 AVCHD 6, 66

B Batteries 16 BD-R 5, 66 BD-RE 5, 66 Blu-ray Disc 5, 66 BRAVIA Theatre Sync 11

C CD 5 Chapter 66 Color buttons 24 Connecting

the audio cords 12 the video cords 10

D DIMMER 24 Disc Information 26 DISPLAY 24 Display

front panel display 59 Dolby Digital 14, 47, 66 Dolby Digital Plus 48, 66 Dolby TrueHD 48, 66 DTS 47, 66 DTS Downmix 47 DTS-HD 48, 66 DVD VIDEO 66 DVD+R 67 DVD+RW 67 DVD-R 67 DVD-RW 67

E Easy Setup 18

F Film based software 67 Front panel display 59

H HDMI 11, 12, 18, 45, 47, 67 HDMI Control 11, 21, 52

I Interlace format 67

L Language 49

M Memory 28 Movies 32 MPEG 32 Music 36

O Options 52

P Parental Control 50 Photos 40 POP UP/MENU 25 Pro Logic 14, 47, 66 Progressive format 67

R Region code 7 Remote 16, 17, 24 Resetting the Player 53

S Searching 26, 34, 38, 42 Setup 22 Setup Displays 44 Slideshow 41 Speaker Setup 51 Speakers 12, 51 SUBTITLE 24

T Title 67 Title List 22 TOP MENU 25 Troubleshooting 54 TV Type 45

U Usable discs 5

V Video based software 67 Video Control 28 Video Setup 45

X x.v.Color 8, 67

Actual total number: PANTONE 2925C Sony BDP-S300/301(US) 3-196-787-13 (1)

3-196-787-13(1)

2007 Sony Corporation

Manualsnet FAQs

If you want to find out how the BDP-S301 Sony works, you can view and download the Sony BDP-S301 Operating Instructions on the Manualsnet website.

Yes, we have the Operating Instructions for Sony BDP-S301 as well as other Sony manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Operating Instructions should include all the details that are needed to use a Sony BDP-S301. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Sony BDP-S301 Operating Instructions is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Sony BDP-S301 Operating Instructions consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Sony BDP-S301 Operating Instructions free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Sony BDP-S301 Operating Instructions, simply download the document to your computer. Once downloaded, open the PDF file and print the Sony BDP-S301 Operating Instructions as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.