Sony ECM-100N Operating Instructions PDF

1 of 2
1 of 2

Summary of Content for Sony ECM-100N Operating Instructions PDF

English Electret Condenser Microphone Before using the microphone, please read this manual thoroughly. This manual should be retained for future reference.

The validity of the CE marking is restricted to only those countries where it is legally enforced, mainly in the countries EEA (European Economic Area) and Switzerland.

Names and Functions of Parts (Fig.) (The numbers refer to the corresponding numbers in the figure.)

Microphone

PAD switch Select the PAD switch to the level of input source.

: Off : On

LOW CUT switch The low cut filter reduces the wind noise effectively.

: Normal setting : The low cut filter is applied.

Output connector (XLR-3-12C type) The sound recorded with the microphone is output. The power is supplied to the microphone from an external equipment through this connector when the microphone is operating on the external power supply.

Wind screen Attach to the microphone to reduce wind or breathing noise.

Microphone holder When using a microphone stand (not supplied), for example, attach the holder to the microphone. When the angle adjustment screw has become loose, tighten it with a coin. A stand adaptor is equipped to the microphone holder. If you do not plan on using the stand adaptor, detach it, and then attach it to a microphone stand (sold separately).

Stand adaptor

Power Supply This microphone is powered only from an external power supply. Connect output connector of the microphone to the microphone connector of a Phantom power supply (external power supply) or an audio mixer. For connection, use a microphone cable.

Note An unbalanced cable cannot be connected to this microphone. Be sure to use a balanced microphone cable.

Notes on Use Microphones are delicate. Do not drop or subject it to excessive shock. Avoid extended usage or storage in high humidity or temperatures above 60 C (140 F).

It may cause noise or failure. If acoustic feedback occurs during use (a howling sound is heard from the speakers),

point the microphone away from the speakers or increase the distance between the microphone and the speakers.

The microphone output signal is a balanced output. Unbalanced output is not supported, so be sure to connect it to the balanced input circuit.

A cable with the connector housing part connected to the ground wire (pin 1) is recommended for the microphone cable. Cables that are not connected to a ground wire may emit noise. If a ground terminal is available, noise can be reduced by connecting to that terminal. Also, if used extending several microphone cables and the connector housing part touches the floor, noise may worsen.

Specifications General Type Electret condenser

Power supply External power supply operation 44 V to 52 V DC (IEC* 61938 P48)

Power consumption Less than 2.5 mA

Output connector XLR-3-12C Type

Dimensions 19 mm dia. 130 mm (0.75 in. dia. 5.12 in.)

Mass Approx. 130 g (4.6 oz)

Supplied accessories Microphone holder (1) Wind screen (1) Stand adaptor (W3/8 - NS5/8) (1) Carrying case (1) Operating instructions (this sheet) (1) Warranty card (1)

Performance Frequency response 20 Hz - 50,000 Hz

Directivity Uni-directional (ECM-100U) Omni-directional (ECM-100N)

Output impedance 100 15%, balanced

Sensitivity -41 dB (ECM-100U) -36 dB (ECM-100N) (deviation3 dB) (0 dB=1 V/Pa, 1 kHz)

Inherent noise Less than 21 dB SPL (0 dB=2 10-5 Pa) (IEC* 61672-1 A-Weighted, 1 kHz, 1 Pa)

Maximum input sound pressure level More than 142 dB SPL (ECM-100U) More than 145 dB SPL (ECM-100N) (output level for 1% waveform distortion at 1 kHz, converted into equivalent input sound pressure level: 0 dB=2 10-5 Pa)

Dynamic range More than 121 dB (ECM-100U) More than 124 dB (ECM-100N)

PAD 0 dB/-10 dB (switchable)

LOW CUT filter Flat/30 Hz (switchable)

* IEC = International Electrotechnical Commission Design and specifications are subject to change without notice.

Note Always verify that the unit is operating properly before use. SONY WILL NOT BE LIABLE FOR DAMAGES OF ANY KIND INCLUDING, BUT NOT LIMITED TO, COMPENSATION OR REIMBURSEMENT ON ACCOUNT OF THE LOSS OF PRESENT OR PROSPECTIVE PROFITS DUE TO FAILURE OF THIS UNIT, EITHER DURING THE WARRANTY PERIOD OR AFTER EXPIRATION OF THE WARRANTY, OR FOR ANY OTHER REASON WHATSOEVER.

Electret Condenser Microphone

Operating Instructions GB

Mode demploi FR

ECM-100U / ECM-100N

4-735-086-13(1)

2018 Sony Corporation Printed in Japan Imprim au Japon http://www.sony.net/

Franais Microphone condensateur lectret Avant dutiliser ce microphone, lisez attentivement ce mode demploi conserver pour toute rfrence ultrieure.

La validit du marquage CE est limite aux pays o il est lgalement appliqu, principalement dans les pays de lEEA (Espace conomique europen) et en Suisse.

Nomenclature (Fig.) (Les numros correspondent ceux des illustrations.)

Microphone

Commutateur PAD Rglez le commutateur PAD au niveau de la source dentre.

 : Dsactiv  : Activ

Commutateur LOW CUT Le filtre passe-haut rduit efficacement le bruit du vent.

 : Rglage normal  : Application du filtre passe-haut.

Connecteur de sortie (type XLR-3-12C) Le son enregistr par le microphone est sorti. Lalimentation est fournie au microphone par un appareil externe via ce connecteur quand le microphone fonctionne sur une alimentation extrieure.

Bonnette anti-vent Mettez-la sur le microphone pour rduire le bruit du vent ou de la respiration.

Support de microphone Quand vous utilisez un pied (non fourni), par exemple, fixez le support au microphone. Quand la vis dajustement de langle est desserre, serrez-la avec une pice de monnaie. Le support de microphone est muni dun adaptateur de pied. Si vous ne prvoyez pas dutiliser ladaptateur de pied, retirez-le, puis fixez-le un pied de microphone (vendu sparment).

Adaptateur de support

Alimentation Ce microphone est aliment uniquement par une alimentation externe. Raccordez le connecteur de sortie du microphone au connecteur pour microphone dune alimentation fantme (alimentation externe) ou dune console audio. Pour effectuer le raccordement, utilisez un cble de microphone.

Remarque Il nest pas possible de connecter un cble asymtrique ce microphone. Assurez-vous dutiliser un cble de microphone symtrique.

Remarques sur lemploi Les microphones sont dlicats. Veillez ne pas les laisser tomber ou les soumettre des

chocs excessifs. vitez toute priode prolonge dutilisation ou de rangement dans les endroits trs

humides ou des tempratures suprieures 60 C (140 F). Cela pourrait causer du bruit ou une dfaillance.

Si une rtroaction acoustique se produit pendant lutilisation (un sifflement mis par les haut-parleurs), dirigez le microphone loppos des haut-parleurs ou augmentez la distance entre le microphone et les haut-parleurs.

Le signal de sortie du microphone est symtrique. Comme les signaux de sortie asymtriques ne sont pas pris en charge, assurez-vous de le connecter un circuit dentre symtrique.

Un cble avec botier de connecteur raccord au fil de masse (broche 1) est recommand comme cble de microphone. Les cbles qui ne sont pas raccords un fil de masse pourraient mettre du bruit. Si une borne de masse est disponible, le bruit peut tre attnu grce au raccordement cette borne. De plus, lors de lutilisation de plusieurs cbles prolongateurs de microphone, le bruit pourrait tre accentu en cas de contact du botier de connecteur au sol.

Spcifications Gnralits Type Condensateur lectret

Alimentation Fonctionnement sur alimentation externe 44 V 52 V CC (CEI* 61938 P48)

Consommation de courant Infrieure 2,5 mA

Connecteur de sortie Type XLR-3-12C

Dimensions 19 mm dia. 130 mm (0,75 po dia. 5,12 po)

Poids Environ 130 g (4,6 oz)

Accessoires fournis Support de microphone (1) Bonnette anti-vent (1) Adaptateur de support (W3/8 - NS5/8) (1) tui de transport (1) Mode demploi (ce feuillet) (1) Carte de garantie (1)

Performances Rponse en frquence 20 Hz - 50 000 Hz

Directivit Unidirectionnelle (ECM-100U) Omnidirectionnelle (ECM-100N)

Impdance de sortie 100  15 %, symtrique

Sensibilit -41 dB (ECM-100U) -36 dB (ECM-100N) (dviation 3 dB) (0 dB=1 V/Pa, 1 kHz)

Bruit inhrent Infrieur 21 dB SPL (0 dB=2 10-5 Pa) (CEI* 61672-1 Mesure pondre A, 1 kHz, 1 Pa)

Niveau de pression acoustique dentre maximale Suprieur 142 dB SPL (ECM-100U) Suprieur 145 dB SPL (ECM-100N) (niveau de sortie pour 1 % de distorsion 1 kHz, converti en niveau de pression acoustique dentre quivalente : 0 dB=2 10-5 Pa)

Plage dynamique Suprieure 121 dB (ECM-100U) Suprieure 124 dB (ECM-100N)

PAD 0 dB/-10 dB (commutable)

Filtre LOW CUT Plat/30 Hz (commutable)

* CEI = Commission lectrotechnique Internationale La conception et les spcifications peuvent tre modifies sans pravis.

Remarque Vrifiez toujours que lappareil fonctionne correctement avant lutilisation. Sony nassumera pas de responsabilit pour les dommages de quelque sorte quils soient, incluant mais ne se limitant pas la compensation ou au remboursement, cause de la perte de profits actuels ou futurs suite la dfaillance de cet appareil, que ce soit pendant la priode de garantie ou aprs son expir

Manualsnet FAQs

If you want to find out how the ECM-100N Sony works, you can view and download the Sony ECM-100N Operating Instructions on the Manualsnet website.

Yes, we have the Operating Instructions for Sony ECM-100N as well as other Sony manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Operating Instructions should include all the details that are needed to use a Sony ECM-100N. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Sony ECM-100N Operating Instructions is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Sony ECM-100N Operating Instructions consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Sony ECM-100N Operating Instructions free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Sony ECM-100N Operating Instructions, simply download the document to your computer. Once downloaded, open the PDF file and print the Sony ECM-100N Operating Instructions as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.