Contents

Sony DPF D92 Operating Instruction PDF

1 of 68
1 of 68

Summary of Content for Sony DPF D92 Operating Instruction PDF

4-129-231-13 (1) P/N7525000004E

Digital Photo Frame DPF-D82/D92

2009 Sony Corporation

Before operation

Basic operations

Advanced operations

Using an external device (with Bluetooth)

Using an external device (with a computer)

Error messages

Troubleshooting

Additional informationOperating Instructions Before operating this unit, please read this manual thoroughly and retain it for future reference.

Owners Record The model and serial numbers are located at the rear. Record the serial number in the space provided below. Refer to these numbers whenever you call upon your Sony dealer regarding this product. Model No. DPF-D82/D92 Serial No. ________________________

To reduce fire or shock hazard, do not expose the unit to rain or moisture.

Do not expose the batteries to excessive heat such as sunshine, fire or the like.

CAUTION

Replace the battery with the specified type only. Otherwise, fire or injury may result. Dispose of used batteries according to the instructions.

For the customers in the U.S.A.

CAUTION You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment.

If you have any questions about this product, you may call: Sony Customer Information Services Center 1-800-222-SONY (7669)

The number below is for the FCC related matters only.

Regulatory Information

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and

receiver. Connect the equipment into an outlet on a circuit

different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

WARNING

Declaration of Conformity Trade Name: SONY Model No.: DPF-D92 Responsible Party: Sony Electronics Inc. Address: 16530 Via Esprillo, San Diego,

CA 92127 U.S.A. Telephone No.: 858-942-2230 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Declaration of Conformity Trade Name: SONY Model No.: DPF-D82 Responsible Party: Sony Electronics Inc. Address: 16530 Via Esprillo, San Diego,

CA 92127 U.S.A. Telephone No.: 858-942-2230 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

2 GB

For the State of California, USA only Perchlorate Material - special handling may apply, See www.dtsc.ca.gov/hazardouswaste/perchlorate Perchlorate Material: Lithium battery contains perchlorate.

For the Customer in Europe This product has been tested and found compliant with the limits set out in the EMC Directive for using connection cables shorter than 3 meters (9.8 feet).

Attention The electromagnetic fields at the specific frequencies may influence the picture of this digital photo frame.

Notice If static electricity or electromagnetism causes data transfer to discontinue midway (fail), restart the application or disconnect and connect the communication cable (USB, etc) again.

Disposal of Old Electrical & Electronic Equipment (Applicable in the European Union and other European countries with separate collection systems)

This symbol on the product or on its packaging indicates that this product shall not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for

the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. The recycling of materials will help to conserve natural resources. For more detailed information about recycling of this product, please contact your local Civic Office, your household waste disposal service or the shop where you purchased the product.

Disposal of waste batteries (applicable in the European Union and other European countries with separate collection systems)

This symbol on the battery or on the packaging indicates that the battery provided with this product shall not be treated as household waste. By ensuring these batteries are disposed of correctly, you will help prevent potentially negative consequences for

the environment and human health which could otherwise be caused by inappropriate waste handling of the battery. The recycling of the materials will help to conserve natural resources. In case of products that for safety, performance or data integrity reasons require a permanent connection with an incorporated battery, this battery should be replaced by qualified service staff only. To ensure that the battery will be treated properly, hand over the product at end-of-life to the applicable collection point for the recycling of electrical and electronic equipment. For all other batteries, please view the section on how to remove the battery from the product safely. Hand the battery over to the applicable collection point for the recycling of waste batteries. For more detailed information about recycling of this product or battery, please contact your local Civic Office, your household waste disposal service or the shop where you purchased the product.

Notice for the customers in the countries applying EU Directives The manufacturer of this product is Sony Corporation, 1-7-1 Konan Minato-ku Tokyo, 108- 0075 Japan. The Authorized Representative for EMC and product safety is Sony Deutschland GmbH, Hedelfinger Strasse 61, 70327 Stuttgart, Germany. For any service or guarantee matters please refer to the addresses given in separate service or guarantee documents.

Continued

3 GB

Notes on LCD screen Do not press against the LCD screen. The screen

may be discolored and that may cause a malfunction.

Exposing the LCD screen to direct sunlight for long periods may cause malfunctions.

The LCD screen is manufactured using extremely high-precision technology, so over 99.99% of the pixels are operational for effective use. However, there may be some tiny black points and/or bright points (white, red, blue or green in color) that constantly appear on the LCD screen. These points are normal in the manufacturing process and do not affect the viewing in any way.

Images may trail across on the LCD screen in a cold location. This is not a malfunction.

On trademarks and copyrights , Cyber-shot, , Memory

Stick, , Memory Stick Duo,

, MagicGate Memory Stick, Memory Stick PRO,

, Memory Stick PRO Duo, , Memory Stick PRO-HG

Duo, , Memory Stick Micro, , , Memory Stick-

ROM, , MagicGate, and are trademarks or registered

trademarks of Sony Corporation. Microsoft, Windows, and Windows Vista are

registered trademarks of Microsoft Corporation in the United States and/or other countries.

Macintosh and Mac OS are registered trademarks of Apple Inc. in the United States and/or other countries.

CompactFlash is a trademark of SanDisk Corporation in the U.S.A.

or xD-Picture Card is a trademark of FUJIFILM Corporation.

The Bluetooth word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by Sony Corpration is under licence. Other trademarks and trade names are those of their resective owners.

Contains iTypeTM and fonts from Monotype Imaging Inc. iTypeTM is a trademark of Monotype Imaging Inc.

All other companies and product names mentioned herein may be the trademarks or registered trademarks of their respective companies. Furthermore, and are not mentioned in each case in this manual.

This unit is equipped with face recognition feature. Sony Face Recognition technology developed by Sony is used.

Duplication, edition, or printing of a CD, TV programs, copyrighted materials such as pictures or publications, or any other materials except for your own recording or creation is limited to private or domestic use only. Unless you hold copyright or have permission of copyright holders for the materials to be duplicated, use of those materials beyond this limit may infringe the provisions of the copyright law and be subject to the copyright holders claim for damages. When using photo images with this digital photo frame, pay special attention not to infringe the provisions of the copyright law. Any unauthorized use or modification of theres portrait may also infringe their rights. For some demonstrations, performances, or exhibits, photography may be forbidden.

Backup recommendations To avoid potential risk of data loss caused by accidental operation or malfunction of the digital photo frame, we recommend that you save a backup copy of your data.

Information IN NO EVENT SHALL SELLER BE LIABLE FOR ANY DIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY NATURE, OR LOSSES OR EXPENSES RESULTING FROM ANY DEFECTIVE PRODUCT OR THE USE OF ANY PRODUCT.

Sony shall assume no responsibility for any accidental or consequential damages or loss of the recording contents which may be caused by use or malfunction of the digital photo frame or memory card.

4 GB

Notice for users Program 2009 Sony Corporation Documentation 2009 Sony Corporation

All rights reserved. This manual or the software described herein, in whole or in part, may not be reproduced, translated or reduced to any machine readable form without prior written approval from Sony Corporation.

IN NO EVENT SHALL SONY CORPORATION BE LIABLE FOR ANY INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES, WHETHER BASED ON TORT, CONTACT, OR OTHERWISE, ARISING OUT OF OR IN CONNECTION WITH THIS MANUAL, THE SOFTWARE OR OTHER INFORMATION CONTAINED HEREIN OR THE USE THEREOF.

Sony Corporation reserves the right to make any modification to this manual or the information contained herein at any time without notice. The software described herein may also be governed by the terms of a separate user license agreement.

Any design data such as sample pictures provided in this software cannot be modified or duplicated except for the purpose of personal use. Any unauthorized duplication of this software is prohibited under copyright law. Please note that unauthorized duplication or modification of portraits or copyrighted work could infringe the rights reserved by rights holders.

On the illustrations and screen shots used in this manual The illustrations and screen shots used in this manual are of the DPF-D92 unless noted otherwise. The illustrations and screen shots used in this manual may not be identical to those actually used or displayed.

5 GB

Table of Contents

Before operation Enjoying your photo frame in various ways ...............................................8 Features ..........................................9 Checking included items ...............11 Identifying the parts .....................11

Basic operations Preparing the remote control ........15 Setting the stand ..........................16 To display the photo frame on the wall .........................................17 Connecting to the AC power source ..........................................18 Turning the photo frame on ..........19 Setting the current time ................20 Inserting a memory card ..............21 Changing the display ....................23 Slideshow display .........................24 Clock and calendar display ...........25 Single view mode .........................26 Index image display ......................27

Advanced operations Enjoying a slideshow ....................29

Changing the settings of the slideshow ................................. 29

Refresh mode ...............................32

Adding images to the internal memory ........................................32 Exporting an image .......................34 Deleting an image .........................36 Registering a mark .......................37 Searching for an image (Filtering) ......................................39 Specifying the playback device .....40 Adjusting the image size and

position ...................................40 Enlarging/reducing an image ..........40 Rotating an image ...........................41

Changing the settings of the auto power on/off function ...................42 Using the alarm function ..............43

Setting the alarm ............................43 Setting the time to be alarmed ........44

Changing the settings ...................44 Setting procedure ...........................44 Items to set .....................................46

Displaying images on a USB memory ........................................48

Using an external device (with Bluetooth) Transferring images using Bluetooth.......................................49

Using an external device (with a computer) Connecting to a computer ............51

System requirements ......................51

6 GB

Connecting to a computer to exchange images ...........................................51 Disconnecting your computer ........52

Error messages If an error message appears .........53

Troubleshooting If trouble occurs ...........................55

Additional information Precautions ..................................60

Safety .............................................60 Installation .....................................60 Cleaning .........................................60 Restrictions on duplication .............61 Disposing of the photo frame ..........61

About memory cards ....................61 Memory Stick ..............................61 SD memory card ............................62 xD-Picture Card .............................62 CompactFlash card ........................62 Notes on using a memory card .......63

Specifications ...............................64 Index ............................................66

7 GB

Before operation

Enjoying your photo frame in various ways The Sony DPF-D82/D92 is a digital photo frame for easily displaying images taken with a digital camera or other device, without using a computer.

8 GB

B efore operation

Features xSupport for various memory cards*

Supports various memory cards and other devices, such as a Memory Stick, CompactFlash card, SD memory card, xD- Picture Card, and USB memory. Just insert a memory card removed from a digital camera or other device, and you will be able to view the images immediately. (.page 21, 48)

xVarious display functions You can enjoy various viewing modes, such as the slideshow display, Clock and calendar display, Single view mode, and Index image display. (.page 23)

xVarious modes The displayed image can be switched automatically as though you are turning the pages of an album yourself. You can select from various modes, including just images, a clock, or calendar view. You can also change playback settings such as the playback order. (.page 29)

xAdding images to internal memory The images you add to the album are saved in internal memory. (.page 32)

xExporting images You can export images in the album to your memory card. (.page 34)

Continued

9 GB

xSearch function You can search for images by the date, folder, image direction, and mark. (.page 39)

xAlarm function The photo frame announces the specified time on the image and using sound. (.page 43)

xAutomatic rotation of images The photo frame automatically rotates images to their proper orientation. Images are also automatically rotated when the photo frame is set in either the portrait or landscape position. (.page 16)

xEasy transfer of images taken with a Bluetooth compatible mobile phone or other device* You can transfer images to the photo frame's internal memory from a Bluetooth compatible device via a Bluetooth adaptor (optional). (.page 49)

xDisplaying images on a wall You can hang the photo frame on the wall. (.page 17)

* We do not guarantee proper operations for all types of devices.

10 GB

B efore operation

Checking included items Make sure that the following items are included.

Digital photo frame (1) Stand (1) Remote control (1) AC adaptor (1) Operating Instructions (this manual) (1) Read This First (1) Warranty (1)

(In some regions, the warranty is not supplied.)

Identifying the parts For details, see the pages indicated in the parentheses.

The illustrations are of the DPF-D92. The locations and names of buttons and connectors of the DPF-D82 are identical to those of the DPF-D92, although the LCD screen size and shape is different.

Front

A LCD screen B Remote sensor

When using the supplied remote control, point it at this sensor.

Continued

11 GB

D:\DPF series\V Series\4129231131\4129231131\4129231131DPFD92CED\01GB-DPFD92CED\030C01.fm Master: Left

Rear

tandard/

the same s on the ow Settings], ate/time

ns, u items. Then

58) tings, and the n to their g, thin object, .

rodrive

D-Picture

030C01.fm Page 12 Wednesday, April 8, 2009 8:58 AM

12 GB

A Connector for USB A/Bluetooth adaptor (.page 49) Connect a Bluetooth adaptor (optional: DPPA-BT1) when you want to transfer images wirelessly from a BLUETOOTH compatible mobile phone or digital camera. You can also connect a USB memory compatible with USB mass storage.

B USB B connector (.page 51) Connect a USB cable when you want to use the photo frame with a computer.

C Stand (.page 16) D DC IN 12 V jack (.page 18)

Insert the plug of the supplied AC adaptor to this jack, and connect to the wall outlet.

E Power Switch (.page 19)

F Memory Stick PRO (S Duo) slot (.page 21)

G Access lamp H Standby indicator I 1 (on/standby) button J MENU button

Displays the menu. From the menu, you can operate functions as those of the button remote control, such as [Slidesh [Rotate], [Add to album] and [D settings].

K Direction (B/b/v/V) butto Press B/b/v/V to select the men press to enter the selection.

L BACK button Returns to the previous screen.

M Reset switch (.page The date/time setting, alarm set auto power on/off settings retur factory default setting. Use a lon such as a pin, to push the switch

N CompactFlash card/Mic slot (.page 21)

O SD memory card/MMC/x Card slot (.page 21)

DPF-D82/D92 4-129-231-13 (1)

B efore operation

P Buzzer Q VIEW MODE button (.page 23) R Alarm switch (.page 43) S Holes for hanging unit on the wall

(.page 17) T Space for storing the stand

Continued

13 GB

Remote control A VIEW MODE button (.page 23) B SLIDE-SHOW ( ) button

(.page 23) C INDEX ( ) button (.page 23) D SINGLE ( ) button

(.page 23) E MENU button F BACK button G 1 (on/standby) button H CLOCK ( ) button (.page 23) I Zoom in ( )/Zoom out ( ) buttons

(.page 40) J ALBUM ( ) button (.page 32) K Direction (B/b/v/V) buttons L (enter) button M ROTATE ( ) button

(.page 40)

14 GB

Basic operations

B

asic operations

Preparing the remote control The supplied lithium battery (CR2025) has already been inserted into the remote control. Pull out the protective sheet before use as shown in the figure.

Using the remote control Point the top end of the remote control towards the remote sensor on the photo frame.

Note

The photo frame may fall if you use the buttons on the photo frame when it is hanging on the wall. Operate the photo frame using the remote control.

Replacing the battery of the remote control If the remote control stops working, replace the battery (CR2025 lithium battery) with a new one.

1 Pull out the battery holder. While pressing in the tab of the battery holder, pull out the battery holder.

2 Remove the old battery from the battery holder and then insert a new battery. Insert the battery so that + is facing upwards.

3 Reinsert the battery holder into the remote control.

Notes

When the lithium battery becomes weak, the operating distance of the Remote control may shorten, or the Remote control may not function properly. In this case, replace the battery with a Sony CR2025 lithium battery. Use of another battery may present a risk of fire or explosion.

Protective sheet

Remote sensor

WARNING Battery may explode if mistreated. Do not recharge, disassemble or dispose of in fire.

Continued

15 GB

Using a battery other than the specified one may result in the battery rupturing.

Dispose of used batteries as specified by the local authorities.

Do not leave the remote control in a very hot and humid place.

Take care that no foreign objects get inside the remote control when you, for example, replace the battery.

Incorrect use of the battery may cause leaking and corrosion.

Do not recharge the battery.

When the remote control will not be used for a long period of time, remove the battery from the remote control to prevent leaking and corrosion.

Incorrectly inserting, shorting, dismantling, or heating the battery, or throwing it into a fire may cause the battery to rupture or leak.

About descriptions in this manual The operations described in this manual are based on remote control operation. When an operation is performed differently, for example, with the remote control and the buttons on the photo frame, it will be explained in a tip.

Setting the stand

1 Hold the photo frame tightly and insert the stand straight into the screw hole on the rear panel.

2 Screw the stand into the screw hole firmly until the stand stops turning.

Setting to portrait or landscape orientation You can set the photo frame to portrait or landscape orientation by rotating it without moving the stand.

16 GB

B asic operations

When the photo frame is placed in the portrait orientation, the image is also automatically rotated to its proper orientation.

The directions indicated on the direction button on the rear panel depend on the orientation of the photo frame.

Notes

Check whether the stand is stable. If the stand is not set properly, the photo frame may fall over.

When the photo frame is placed in the portrait orientation, the Sony logo doesn't light up.

The photo frame does not detect and rotate the orientation of images when [Auto display orientation] of [General Settings] on the (Settings) tab is set to [OFF].

A magnet is contained in the storage portion of the stand. Do not keep anything that is easily affected by magnetism, such as a cash card or credit card, near the photo frame. If you place the photo frame near a CRT-based television, the color of the TVs display may be changed.

Tip

It is easier to turn the stand if you wind or wrap a rubber band tightly around the stand when you remove the stand from the photo frame.

To display the photo frame on the wall You can hang the photo frame on the wall using the following procedure.

1 Prepare screws (not supplied) suitable for the screw holes on the rear panel.

2 Screw the screws (not supplied) into the wall. Be sure the screws (not supplied) protrude between 2.5 to 3mm (1/8 inch) from the surface of the wall.

3 Hang the photo frame on the wall by fitting the hole on the rear panel to the screws on the wall.

Notes

Use screws suitable for the quality of the material of the wall. The screws may be damaged, depending on the type of material used in the wall. Set the screws in a pillar or stud in the wall.

4mm (3/16 inch)

More than 25mm (1 inch)

4.2mm (3/16 inch)

8.6mm (11/32 inch)

Holes for hanging the unit on the wall

Between

2.5mm to 3mm (1/8 inch)

Continued

17 GB

When you want to re-insert the memory card, remove the photo frame from the wall, then eject and re-insert the memory card while the photo frame is placed on a stable surface.

Store the stand in the place provided when you hang the photo frame on the wall.

Connect the plug of the supplied AC adaptor to the photo frame and set the power switch to ON. And then connect the AC adaptor to the wall outlet after hanging the photo frame on the wall.

We take no responsibility for any accidents or damage caused by defects of attachment, misuse, or natural disasters, etc.

Connecting to the AC power source

1 Insert the plug of the AC adaptor into the DC IN 12 V jack on the rear of the photo frame.

2 Connect the AC adaptor to the wall outlet.

Notes

The socket outlet should be as close as possible to the unit, and easily accessible.

Do not place the photo frame in an unsteady location such as on an unsteady table or tilted surface.

Connect the AC adaptor to an easily accessible wall outlet close by. If trouble occurs while using the adaptor, immediately shut off the power by disconnecting the plug from the wall outlet.

Do not short the plug of the AC adaptor with a metal object. Doing so may cause a malfunction.

Do not use the AC Adaptor placed in a narrow space, such as between a wall and furniture.

AC adaptor

To wall outlet

To the DC IN 12 V jack

18 GB

B asic operations

Insert the plug of the AC adaptor firmly, if the connection is loose, the photo frame may turn off when it is moved.

After use, remove the AC adaptor from the DC IN 12 V jack of the photo frame, and remove the AC adaptor from the outlet.

Even if your photo frame is turned off, AC power (house current) is still supplied to it while connected to the wall outlet via the AC adaptor.

Do not turn the photo frame off or disconnect the AC adaptor from the photo frame before the standby indicator turns red. Doing so may damage the photo frame.

Turning the photo frame on

When the power switch is set to off When the power switch is set to on, the standby indicator turns green and the Sony logo on the front panel lights up.

When the power switch is set to on Press 1 (on/standby) on the photo frame or remote control to turn on the power. The standby indicator turns to green from red. The Sony logo on the front panel lights up.

Continued

19 GB

Turning off the power Hold 1 (on/standby) on the photo frame or remote control until the power turns off. The standby indicator turns to red from green.

Note

Do not turn the photo frame off or disconnect the AC adaptor from the photo frame before the standby indicator turns red. Doing so may damage the photo frame.

Operations in an initial state When the photo frame is turned on without a memory card connected, the initial display below appears on the screen.

If the photo frame is not operated for 10 seconds, the demo mode is displayed. If any other button than the power button is pressed, the screen returns to the initial display.

First, press MENU during the initial display, and then set the date and time.

Setting the current time The clock of the photo frame needs to be adjusted in order to display an accurate time in the clock and calendar view modes.

1 Press MENU. The menu screen is displayed.

2 Press B/b to select the (Settings) tab. The settings screen is displayed.

Tip

You can use the B/b button only when a memory card is inserted in the photo frame, an external device is connected, or anything other than the clock and calender settings item (page 25) are selected.

3 Press v/V to select [Date/time settings] and then press . The Date/time settings screen is displayed.

4 Adjust the date. 1Press v/V to select [Date] and then

press . 2Press B/b to select month, day, and

year, and then press v/V to select a value, then press .

5 Adjust the time. 1Press v/V to select [Time] and then

press . 2Press B/b to select hour, minute, and

second, and then press v/V to select a value, then press .

20 GB

B asic operations

6 Select the format of the date. 1Press v/V to select [Date Display Order]

and then press . 2Press v/V to select a format and then

press . Y-M-D M-D-Y D-M-Y

7 Set the day to start the week for the calendar. You can set the day that appears on the very left when the calendar is displayed.

1Press v/V to select [First Weekday] and then press .

2Press v/V to select [Sunday] or [Monday] and then press .

8 Select the time display. 1Press v/V to select [12hr/24hr display]

and then press . 2Press v/V to select [12 hours] or

[24 hours] and then press .

9 Press MENU. The menu screen is closed.

Inserting a memory card

Insert the memory card firmly into the corresponding slot with its label side facing toward you (when you are facing the back side of the photo frame).

The access lamp flashes when the memory card is inserted correctly. Reinsert the memory card after checking the label side of the memory card if the access lamp does not flash.

For details on the memory cards you can use with this photo frame, see pages 61 to 63.

Insert the memory card firmly into the corresponding slot with its label side facing toward you. The slot order from the top is Memory Stick (Memory Stick Duo), CompactFlash card, SD memory card and xD- Picture Card.

Access lamp

Continued

21 GB

To remove a memory card Remove the memory card from its slot in the opposite direction from which it was inserted.

Notes

When inserting the memory card, it will only insert part of the way, so do not try to force it as this could damage the memory card and/or photo frame.

This photo frame has a slot that is both a Memory Stick standard and Duo size compatible slot, so you do not need a Memory Stick adaptor.

The SD memory card/xD-Picture Card dual- purpose slot automatically detects the card type.

Before using a memory card, see About memory cards on page 61.

Display priority of images If a memory card is inserted or an external device is connected, the images of the inserted memory card or connected device are displayed automatically.

To manually change the memory card or external device to be displayed, specify it in (Select device) menu (page 40).

The photo frame displays the images of the memory card in the following priorities.

Memory card / The device connected to the USB A/Bluetooth connector t internal memory

If multiple memory cards are inserted when the photo frame is turned on, the images of the first memory card you inserted take priority and are displayed.

If multiple devices are inserted while the photo frame is turned off, and then the photo frame is turned on, the images of the device displayed when the photo frame is turned off take the first priority and are displayed. A device connected to the USB A/Bluetooth connector, however, may not be able to take priority.

If a memory card is replaced while the photo frame is turned off, and then the photo frame is turned on, the images are displayed in the following priorities: Memory Stick b CompactFlash card b SD memory card b xD-Picture Card b the device connected to the USB A/Bluetooth connector b internal memory

If no memory card is inserted and no device is connected, the images saved in the album in the internal memory are displayed.

Notes

Due to one of the characteristics of the internal memory device, images stored for long time or read many times may be subject to data error when read too often.

For the file formats that the photo frame can display, see page 64.

22 GB

B asic operations

Changing the display

1 Press VIEW MODE. The view mode screen is displayed.

2 Select the group you want.

Tip

Select the group you want using B/b after moving the cursor to the group area using B/b/ v/V, when you operate the photo frame using the buttons on the photo frame.

3 Press B/b/v/V or VIEW MODE to select the style you want and then press .

Note

If you have not operated the photo frame for an extended period of time, the style the cursor is on will be selected automatically.

Group Explanation

Slideshow

Displays a slideshow display style.

Clock and calendar

Displays a clock or calendar style.

Displays a single image style.

Index

Displays a thumbnail list style.

23 GB

Slideshow display

Tips

If the power is on, and no memory card is inserted, and no device is connected, the images stored in internal memory are displayed. If no images are saved in internal memory, demonstration mode starts automatically. Demonstration mode ends if a button other than 1 (on/standby) is pressed.

For details on the playback order in a slideshow display, see page 46.

You can set the interval, effect, listing order, or color effect when you select the slideshow display. Refer to Slideshow Settings (page 31).

You can select the single view mode when you press on the photo frame when the image you want appears in the slideshow display.

You can use the VIEW MODE button on the photo frame.

Group Image Style Explanation

Slideshow

A Single view Displays one image after another.

B Multi image view Displays multiple images at the same time.

C Clock view Displays images with the present date and time.

D Calendar view Displays images, one after another, while showing a calendar. The present date and time is displayed.

E Time Machine Displays images with the shooting date and time. The present date and time cannot be displayed.

F Random view Displays images while randomly switching between a number of different slideshow styles and effects.

A B C D

E F

24 GB

B asic operations

Clock and calendar display

Note

You can select only the (Settings) tab when the Clock and calendar display is displayed.

Tip

You can use the VIEW MODE button on the photo frame.

Clock1 Clock2 Clock3 Clock4 Clock5

Clock6 Clock7 Clock8 Clock9 Clock10

Clock11

Calendar1 Calendar2 Calendar3

Lunar Calendar (when you select

[Simplified Chinese] in

[Language setting])

Arabic Calendar (when you select

[Arabic] in [Language setting])

Farsi Calendar (when you select

[Persian] in [Language setting])

25 GB

Single view mode

Tips

If the power is on, and no memory card is inserted, and no device is connected, the images stored in internal memory are displayed. If no images are saved in internal memory, demonstration mode starts automatically. Demonstration mode ends if a button other than 1 (on/standby) is pressed.

You can set the image display mode by pressing VIEW MODE and pressing B/b to select either entire image or fit to screen mode. Not all images are able to use the fit to screen mode.

You can use the VIEW MODE button on the photo frame.

Group Image Style Explanation

A Entire image Displays an entire image in the screen. You can switch the images to be displayed by pressing B/b.

B Fit to screen Displays an image over the whole screen. You can switch the images to be displayed by pressing B/b.

C Entire image (with Exif)

Displays image information, such as the image number, file name, and shooting date while displaying the entire image. You can switch the images to be displayed by pressing B/b. Refer to About the information display (page 28) for details on the image information.

D Fit to screen (with Exif)

Displays image information, such as the image number, file name, and shooting date in fit to screen mode. You can switch the images to be displayed by pressing B/b. Refer to About the information display (page 28) for details on the image information.

A B C D

26 GB

B asic operations

Index image display

Tips

A thumbnail is a small-sized image for index use that is recorded in the pictures taken by a digital camera.

If the power is on, and no memory card is inserted, and no device is connected, the images in internal memory are displayed. If no images are saved in internal memory, demonstration mode starts automatically. Demonstration mode ends if a button other than 1 (on/standby) is pressed.

You can select the single view mode when you press on the photo frame when the image you want appears in the index image display.

You can use the VIEW MODE button on the photo frame.

Group Image Style Explanation

Index

A Index 1 Displays a list of large thumbnails. You can select an image by pressing B/b/v/V.

B Index 2 Displays a list of thumbnails. You can select an image by pressing B/b/v/V.

C Index 3 Displays a list of small thumbnails. You can select an image by pressing B/b/v/V.

A B C

Continued

27 GB

About the information display

The following information is displayed.

1Display type Entire image Fit to screen Entire image (with Exif) Fit to screen (with Exif)

2Ordinal number of the displayed image/Total number of images Input media indication for the displayed image is shown as follows:.

3Image details File format (JPEG(4:4:4), JPEG(4:2:2),

JPEG(4:2:0), RAW) Number of pixels (width height) Manufacturer name of image input device Model name of image input device Shutter speed (e.g.: 1/8) Aperture value (e.g.: F2.8) Exposure value (e.g.: +0.0EV) Rotation information

4Setting information

5Image number (folder-file number) This is displayed if the image is DCF compliant. If the image does not comply with DCF, up to 10 characters of its file name are displayed.

6Shooting date/time

Icons Meaning

Memory Stick input

SD Memory Card input

CompactFlash input

xD-Picture Card input

External Device input

Internal memory input

Icons Meaning

Protect indication

Associated file indication (Displayed when there is an associated file such as a motion file or a miniature e-mail image file.)

Displays when you have registered a mark.

28 GB

Advanced operations

A

dvanced operations

Enjoying a slideshow You can display images stored in the internal memory or on a memory card, one after another, automatically.

When you turn on the photo frame, the slideshow plays continuously from the previous play.

1 Press VIEW MODE. The view mode screen is displayed.

2 Select (slideshow).

Tip

Select (slideshow) using B/b after moving the cursor to the group area using B/b/v/V when you operate the photo frame using the buttons on the photo frame.

3 Press B/b/v/V to select the style you want, then press .

Refer to Slideshow display (page 24) for details on the slideshow styles.

1 Press MENU. The menu is displayed.

2 Press B/b to select the (Settings) tab. The settings screen is displayed.

3 Press v/V to select [Slideshow Settings] and then press . The slideshow settings screen is displayed.

4 Press v/V to select the item and then press . Refer to the tables on the next page for details on the setting items.

Notes

Note the following when you select a slideshow using the image stored on the memory card.

Due to one of the characteristics of the memory card devices, images may be subject to data error when read too often.

Do not run a slideshow for a long time with a small number images. This may cause data error.

We recommend you back up images on the memory card often.

When the photo frame is, for instance, displaying a slideshow, changes to the settings of some items are unavailable. These items are displayed in gray and cannot be selected.

The slideshow starts from the first image if you set the power switch to OFF before entering the standby mode, if you reset the photo frame.

Changing the settings of the slideshow

Continued

29 GB

When the screen is too bright, it may make you feel nauseous. Be careful that you do not make the brightness settings too bright when you use the photo frame.

Tip

You can also use the VIEW MODE button on the photo frame.

30 GB

A dvanced operations

*: Factory default settings

Item Setting Description Slideshow Settings

Interval Set a value from 3 sec., 7 sec.*, 20 sec., 1 min., 5 min., 30 min., 1 hour, 3 hours, 12 hours, 24 hours for the interval between images.

Note An image may not switch at the intervals you set on the menu, depending on the style of the slideshow, color effect, or image size.

Effect Center cross Transitions to the next image as though the previous image is being pushed from the center to the four corners.

Vert. blinds Transitions to the next image as though blinds are being lowered vertically.

Horiz. blinds Transitions to the next image as though blinds are being pulled horizontally.

Fade* Transitions to the next image by fading out the current image and fading in the next image.

Wipe Transitions to the next image as though the current image is being wiped off the screen to reveal the next image.

Random Uses the above five effects randomly.

Shuffle ON Displays images randomly.

OFF* Displays images according to the [Listing Order] setting of [General Settings].

Color effect Color* Displays an image in color.

Sepia Displays an image in a sepia color.

Monochrome Displays an image in monochrome.

Display Mode Select the desired display size from the following:

Note The original image data will not change.

Entire image* Displays an entire image enlarged to proper size. (An image may be displayed with margins on the top, bottom, left and right.)

Fit to screen Zooms in at the center of the image enough to fill the whole screen.

Note An image may not display with the display size you set on the menu, depending on the style of the slideshow.

31 GB

Refresh mode Due to one of the characteristics of the device, images stored for a long time or read many times may be subject to data error when read too often.

This photo frame refreshes the internal memory automatically to prevent these errors, depending on the status of the internal memory.

The confirmation screen used for refreshing the internal memory is displayed automatically when the refresh is needed.

The refresh starts when you select [OK]. The Refresh also starts automatically when no operation is attempted for 30 seconds. If you select [Cancel], the confirmation screen used for refreshing the internal memory is displayed the next time.

Do not turn the photo frame to OFF while the internal memory is being refreshed. It may cause a malfunction.

It may take approximately 5 minutes to refresh the internal memory.

Notes

We recommend that you perform a backup of your data periodically to avoid losing it.

Do not run a slideshow with less than 10 images continuously if you have set the interval time for the slideshow to 3 seconds. You may not be able to protect some images in the internal memory.

Adding images to the internal memory You can use the photo frame as a digital album, saving important images in the internal memory.

Tip

In [Image file size] of the menu, you can preset whether to optimize the size of images or save images as is, without compressing them, when you save them to the internal memory (page 46).

When [Image file size] is set to [Album], up to approx. 2,000 images can be added to the album. When set to [Original], the number of images that can be saved may vary, depending on the original image file size.

1 Press (Album) when an image stored on the memory card or the external device is displayed on the screen.

Tip

Select [Add to album] using v/V after pressing the MENU button and then select (Editing) using B/b.

Single image display

32 GB

A dvanced operations

Slideshow display

Index image display

2 Press v/V to select [Add this image], [Selected images] or [Add all images] and then press . If you select [Add this image], the image currently displayed is added to the album. Go to step 4. (This item cannot be selected on the slideshow display.)

If you select [Selected images], you can select the image you want to add from the image list. Go to step 3.

If you select [Add all images], the image list is displayed. A check mark is attached to the check box of all the images. Go to step 4.

3 Specify the image to add from the image list. About the image list

During a search: Displays all the images applicable to the criteria used for the search.

Other than during a search: Displays all images in the device displayed on the screen.

Refer to Searching for an image (Filtering) (page 39).

1Press B/b/v/V to select the image to add to the album and then press . A check mark will be attached to the check box of each selected image. Repeat this operation to add multiple images at the same time.

To cancel the selection, select images to cancel and then press to delete the check mark in the check box.

2Press MENU. The confirmation screen used for selecting a folder is displayed.

4 Press v/V to select the folder you want and press . The confirmation screen used to decide whether to add an image or not to the internal memory is displayed.

Tip

A new folder is created automatically when you select [New folder].

5 Press v/V to select [Yes] and then press . The image is saved in the specified folder in internal memory.

Continued

33 GB

6 Press when the confirmation screen is displayed.

Notes

Images in the internal memory cannot be added to the album.

Do not turn off the power, remove the memory card, or disconnect the external device while an image is being added. Doing so may damage the photo frame or memory card, or damage the data.

Tips

To perform this operation using the remote control, press the MENU button on the remote control and then press v/V to select [Add to album] from (Editing) and then press .

You can also use the MENU button on the photo frame.

You can change the thumbnail size using [ / ] in the image list.

Due to one of the characteristics of the internal memory device, images stored for long time or read many times may be subject to data error when read too often. We recommend that you perform a backup of your data periodically to avoid losing it.

Exporting an image You can export the images in the internal memory to a memory card or external device.

1 Press MENU when an image stored on the internal device is displayed on the screen. The menu is displayed.

2 Press B/b to select the (Editing) tab. The screen used for editing is displayed.

3 Press v/V to select [Export] and then press . The Export menu is displayed.

Single image display

4 Press v/V to select [Export this image], [Selected images] or [Export all images] and then press . If you select [Export this image], the image currently displayed is exported to the device. Go to step 6. (This item cannot be selected on the slideshow display.)

If you select [Selected images], you can select the image you want to export from the image list. Go to step 5.

If you select [Export all images], the image list is displayed. A check mark is attached to the check box of all the images. Go to step 6.

34 GB

A dvanced operations

5 Specify the image to export from the image list. About the image list

During a search: Displays all the images applicable to the criteria used for the search.

Other than during a search: Displays the image list of the album on the screen.

Refer to Searching for an image (Filtering) (page 39).

1Press B/b/v/V to select the image you want to export and then press . A check mark will be attached to the check box of each selected image. Repeat this operation to export multiple images at the same time. To cancel the selection, select images to cancel and then press to delete the check mark in the check box.

2Press MENU. The screen used for selecting the device to which to export is displayed.

6 Press v/V to select the device to which to export the image and then press .

7 Press v/V to select the folder you want to save to and press . The confirmation screen used to decide whether to export or not is displayed.

Tip

A new folder is created automatically when you select [New folder].

8 Press v/V to select [Yes] and then press . The exporting is finished.

9 Press when the confirmation screen is displayed. The image is copied to the specified device.

Note

Do not turn off the power, remove the memory card, or disconnect the external device during exporting. Doing so may damage the photo frame or memory card, or damage the data.

Tips

You can also use the MENU button on the photo frame.

You can enlarge or reduce the image to export when you select the index image display.

Any device that is not recognized by the photo frame is displayed in gray and you cannot select it.

35 GB

Deleting an image

1 Press MENU when an image is displayed on the screen. The menu is displayed.

2 Press B/b to select the (Editing) tab. The screen used for editing is displayed.

3 Press v/V to select [Delete] and then press .

4 Press v/V to select [Delete this image], [Selected images] or [Delete all images] and then press . If you select [Delete this image], the image currently displayed is deleted. Go to step 6. (This item cannot be selected on the slideshow display.)

If you select [Selected images], you can select the image you want to delete from the image list. Go to step 5.

If you select [Delete all images], the image list is displayed. A check mark is attached to the check box of all the images. Go to step 6.

5 Specify the image to delete from the image list. About the image list

During a search: Displays all the images applicable to the criteria used for the search.

Other than during a search: Displays all images in the device displayed on the screen.

Refer to Searching for an image (Filtering) (page 39).

1Press B/b/v/V to select the image to delete and then press . A check mark will be attached to the check box of each selected image. Repeat this operation to delete multiple images at the same time.

To cancel the selection, select images to cancel and then press to delete the check mark in the check box.

2Press MENU. The delete confirmation screen is displayed.

6 Press v/V to select [Yes] and then press . The image is deleted.

7 Press when the confirmation screen is displayed.

To format the internal memory

1 Press MENU. The menu is displayed.

2 Press B/b to select the (Settings) tab. The settings screen is displayed.

3 Press v/V to select [Initialize] and then press .

4 Press v/V to select [Format internal memory] and then press . The confirmation screen used for initializing the internal memory is displayed.

5 Press v/V to select [Yes], then press .

Notes

When the message [Cannot delete a protected image.] appears on the screen, the image file was set to Read Only on a computer. In this case, connect the photo frame to a computer, and delete this file using the computer.

The total capacity of the internal memory is not equal to the remaining capacity, even immediately after initialization.

If deletion has started, the deleted image cannot be recovered even if you stop deletion. Delete images only after confirming you actually want to delete them.

36 GB

A dvanced operations

Tips

You can also use the MENU button on the photo frame.

You can enlarge or reduce the image when you select the index image display.

Registering a mark You can produce a slideshow only with images which have been selected beforehand and have been marked. You can easily check for images with marks using the index image display or single view mode.

1 Press MENU when an image is displayed on the screen. The menu is displayed.

2 Press B/b to select the (Editing) tab. The screen used for editing is displayed.

3 Press v/V to select [Marking] and then press .

4 Press v/V to select the mark you want and then press .

5 Press v/V to select [Mark this image], [Selected images] or [Mark all images] and then press . If you select [Mark this image], the image currently displayed will be marked and showed in the future. Go to step 7. (This item cannot be selected on the slideshow display.)

If you select [Selected images], you can select the image to which you want to attach a mark from the image list. Go to step 6.

If you select [Mark all images], the image list is displayed. A check mark is attached

Continued

37 GB

to the check box of all the images. Go to step 7.

6 Specify the image to which you want to attach a mark from the image list. About the image list

During a search: Displays all the images applicable to the criteria used for the search.

Other than during a search: Displays all images in the device.

Refer to Searching for an image (Filtering) (page 39).

1Press B/b/v/V to select the image to which to attach and then press . A check mark will be attached to the image. Repeat this operation to attach a mark to multiple images at the same time. To cancel the selection, select an imeges you want to cancel and then press to remove the check mark from the check box.

2A mark will be attached to the image for which a check mark has been placed in the check box. If a check mark is removed from the check box of an image, the mark will be removed from the image.

7 Press v/V to select [Yes] and then press . The mark is attached to the selected image.

To delete the registration of a mark Select [Unmark this image] or [Unmark all images] and then press in step 5. You can also cancel the selection when you remove the check mark from the check box.

[Unmark this image]: Removes a mark from the image currently displayed. (This item cannot be selected on the slideshow display.)

[Unmark all images]

During a search: Removes a marks from all the images applicable to the criteria specified in the search.

Other than during a search: Removes all marks from all images stored on the device displayed.

Note

A mark is saved only when it is registered with an image in the internal memory. A mark registered with an image on a memory card or an external device is removed when the power is turned off, or if you change the device being displayed.

Tips

You can select a mark from among 3 types.

You can also use the MENU button on the photo frame.

You can enlarge or reduce the image when you select the index image display.

38 GB

A dvanced operations

Searching for an image (Filtering)

You can search for an image which is stored in internal memory or on a memory card. You can filter an image using various criteria, such as the date, the folder in which the image is saved, the orientation of the image or mark, etc.

1 Press MENU when an image is displayed on the screen. The menu is displayed.

2 Press B/b to select the (Editing) tab. The screen used for editing is displayed.

Note

You cannot select the (Editing) tab when the clock and calendar are displayed.

3 Press v/V to select [Search] and then press .

4 Press v/V to select the criteria you want and then press .

[Search by date]: Filters by the date. [Search by folder]: Filters by the folder. [Search by vertical/horizontal]: Filters

by the image orientation. [Search by mark]: Filters by the mark.

5 Press v/V to select the item you want and then press .

To cancel the search for an image Press the MENU button when an image is displayed on the screen and then select [Exit search (show all photo)].

To change the criteria for a search Press the BACK button when an image you searched for is displayed on the screen.

Notes

Do not turn off the power, remove the memory card, or disconnect the external device during a searching. Doing so may damage the photo frame or memory card, or damage the data.

The search is cancelled automatically in the following cases.

When you change the playback device

When you search for an image which is stored on a memory card or external device and then remove that memory card or external device

Tip

You can also use the MENU button on the photo frame.

39 GB

Specifying the playback device You can specify the memory card or external device to be displayed.

1 Press MENU. The menu is displayed.

2 Press B/b to select the (Select device) tab. The screen used for selecting a device is displayed.

Tip

Insert the device at this point during the procedure if the device you want to use cannot be selected.

3 Press v/V to select the device you want to display and then press . The images of the selected device are displayed.

Tips

You can also use the MENU button on the photo frame.

The search is cancelled automatically when you change the playback device during a search.

Adjusting the image size and position

You can enlarge or reduce an image in single view mode.

1 To enlarge an image, press (zoom in) on the remote control. To reduce an enlarged image, press (zoom out). Each press of the button enlarges the image further. You can enlarge an image to a maximum of 5 times the original scale. You can move an enlarged image up, down, left, and right.

About crop and save The screen currently displayed is saved as it

was trimmed after you press B/b/v/V to move the enlarged image and then press the MENU button.

You can select [Save as new image] or [Overwrite] by pressing the MENU button when the image is enlarged or reduced. Press v/V to select the method used to save the image.

If you select [Save as new image], the image is saved as a new image.

If you select [Overwrite], the image is overwritten. A confirmation screen is displayed when you select [Overwrite]. Press v/V to select [Yes] and then press to save the image. Press again when the confirmation screen is displayed after saving is finished.

Notes

Enlarging an image may reduce the quality depending on the image size.

It is not possible to enlarge an image using the buttons on the photo frame.

Enlarging/reducing an image

40 GB

A dvanced operations

Press ROTATE ( ) on the remote control. Each press of the button rotates the image 90 degrees counter-clockwise.

Operate from the menu of the photo frame

1 Press MENU in single display mode. The menu is displayed.

2 Press B/b to select the (Editing) tab. The screen used for editing is displayed.

3 Press v/V to select [Rotate] and then press . The Rotate menu is displayed.

4 Press v/V to select the direction to rotate and then press . :

Rotates the image 90 degrees clockwise.

: Rotates the image 90 degrees counter- clockwise.

5 Press v/V to select [OK] and then press .

Note

An enlarged image cannot be rotated.

Tips

For an internal memory image, image rotation data will be retained even after the power is turned off.

You can rotate the image of the index image display.

Rotating an image

41 GB

Changing the settings of the auto power on/off function The timer function to turn the photo frame on/ off automatically can be set. Main power needs to be switched ON for this function.

1 Press MENU. The menu is displayed.

2 Press B/b to select the (Settings) tab. The settings screen is displayed.

3 Press v/V to select [Auto power ON/ OFF] and press . The screen used for setting a value for [Auto power ON/OFF] is displayed.

4 Press v/V to select [Setup method], and press . Then press v/V to select [Simple] or [Advanced], and press . [Simple]: Sets the auto power ON/OFF function finely in one minute increments.

[Advanced]: Sets the auto power ON/OFF function according to a day of the week by one hour units.

5 Set the time setting.

[Simple]

1Press v/V to select [Auto power ON/ OFF] and then press .

2Press v/V to select [Enable] and then press .

3Set the auto on/off timer. Press v/V to set the time you want. AM or PM is displayed on the right of the screen when you select [12 hours] on the time display setting.

4Set the auto ON/OFF day. Press v/V to select the day you want to use this function and then press to check. Press v/V to select [OK] and then press .

[Advanced]

1Press B/b/v/V to select the time you want to use the auto power on/off function. You can set this function according to a day of the week by one hour units. The color of the selected time zone changes to blue after you press . The power supply of the photo frame will be turned on when the blue time zone time occurs. The color of the selected time

42 GB

A dvanced operations

zone changes to gray, after you select the blue time zone and then press . The power supply of the photo frame is turned off while it is in the gray time zone.

Tip

The power is turned off automatically at the time you set for [Auto power OFF] when you are using the photo frame.

The power is turned on automatically at the time you set for [Auto power ON] during the standby mode.

2Press B/b/v/V to select [OK].

Using the alarm function You can use the photo frame as an alarm clock.

Set to the alarm switch on the rear panel to ON. Under condition of main power switch set to On, the alarm sound and alarm mode screen will appear at the scheduled alarm time.

To turn off the alarm Set the alarm switch on the rear panel to OFF.

The alarm is stopped although an alarm screen continues to be displayed.

The normal screen is displayed after you press any button on the photo frame other than 1 (on/standby).

Setting the alarm

Continued

43 GB

1 Press MENU. The menu is displayed.

2 Press B/b to select the (Settings) tab. The settings screen is displayed.

3 Press v/V to select [Alarm Setting] and press .

4 Press v/V to set the time you want.

Tips

To set the clock, refer to Setting the current time (page 20).

Auto power on/off will not function during alarm is set off.

When alarm sets off at scheduled time, power will also turn on regardless of auto off settings. Main power needs to be set at ON for alarm to operate.

Changing the settings You can change the following settings.

Slideshow Settings Alarm Setting Auto power ON/OFF Date/time settings General Settings (Listing Order, Sony logo

ON/OFF etc,.) Language setting Initialize

1 Press MENU. The menu is displayed.

2 Press B/b to select the (Settings) tab. The settings screen is displayed.

Setting the time to be alarmed

Setting procedure

44 GB

A dvanced operations

3 Press v/V to select the item you want to change and then press . The setting screen of the selected item is displayed.

For example, when [Slideshow Settings] is selected.

4 Press v/V to select the item you want to change and then press . This enables you to set each of the items (page 46).

Note

When the photo frame is, for instance, displaying a slideshow, some settings of some items cannot be changed. They are displayed in gray and cannot be selected.

5 Press v/V to select a setting value and then press . Each time you press v/V (v/V from the photo frame), the setting value changes. In the case of a numerical value, press V to increase the value and press v to decrease the value.

If you press , the setting is confirmed.

6 Press MENU. The menu closes.

To reset to factory default settings

1 Press MENU and then select (Settings) - [Initialize] by pressing B/b/v/V.

2 Press v/V to select [Reset] and then press .

All adjusted values, except for the clock settings, are reset to the default settings.

Tip

You can also use the MENU button on the photo frame.

Continued

45 GB

Items to set

*: Factory default settings

Item Setting Description Slideshow Settings

Refer to Enjoying a slideshow (page 29).

Alarm Setting Sets the specific time for an alarm. (.page 43)

Auto power ON/OFF

Sets the timer function which turns the power supply of the photo frame on or off, automatically. You can use this function with the following settings. (.page 42)

Simple Power-ON timer

You can set the timer (time/day) and input time for the power to turn on automatically, when you set this function to enable.

Power-OFF timer

You can set the timer (time/day) and input time for the power to turn off automatically, when you set this function to enable.

Advanced OK Returns to the previous screen after confirming the operation.

Cancel Returns to the previous screen after cancelling the operation.

Reset all Deletes all the selected times.

Setup method Advanced* Sets the auto power ON/OFF function according to a day of the week by one hour units.

Simple Sets the auto power ON/OFF function finely in one minute increments.

Date/time settings

Sets the date, time, first day of a week, etc. (.page 20)

General Settings

Listing Order Sets the display order of images. This setting affects the order in [Slideshow Settings].

Number Order* Displays images in order of file name.

Shoot. Date Displays images in order of shooting date.

Auto display orientation

ON*/OFF: You can set the photo frame to automatically detect and rotate the orientation of images.

LCD backlight Allows you to set the brightness of the backlight of the LCD screen to a level from 1 to 10*.

Beep ON*/OFF: Sets the beep sound on/off.

Image file size Album* Compresses images and saves them in the internal memory, that you can save more images. Be aware that deterioration in image quality compared to the original images is noticeable when the images are displayed on a large monitor via a computer.

Original Saves images to the internal memory without compressing them. There is no deterioration, but you can save fewer images.

Sony logo ON/ OFF

ON*/OFF: You can set whether the photo frame's Sony logo lights or not.

46 GB

A dvanced operations

System Information

Version Displays the version of the firmware of the photo frame.

Internal memory

Memory capacity

Indicates the maximum amount of space available in internal memory in the initial state.

Remaining capacity

Indicates the amount of free space currently available in internal memory.

Bluetooth Address

Displays when the Bluetooth adapter is connected to the photo frame.

Language setting

Sets the display language on the LCD screen. Japanese, English*, French, Spanish, German, Italian, Russian, Korean, Simplified Chinese, Traditional Chinese, Dutch, Portuguese, Arabic, Persian, Hungarian, Polish, Czech, Thai, Greek, Turkish, Malay, Swedish, Norwegian, Danish, Finnish

Note Default language setting may vary in some regions.

Initialize Format internal memory

You can format the internal memory.

Notes All the images added to the internal memory will be deleted. Do not format the internal memory by using a connection to a PC or

other external device.

Reset Returns all settings to their factory defaults except for the current date and time setting of the [Date/time settings].

*: Factory default settings

Item Setting Description

47 GB

Displaying images on a USB memory You can connect a mass-storage-complaint USB memory device to the photo frame and display an image directly from the USB memory.

Notes

We cannot guarantee connection with all types of mass storage devices.

The playback device will be switched to the USB memory if you connect the USB memory to the USB A/Bluetooth jack during playback the internal memory.

1 Connect the photo frame to the AC power source. (.page 18)

2 Turn the photo frame to ON. (.page 19)

3 Connect the USB memory to the USB A/Bluetooth connector.

4 Select the playback device. (.page 40) An image on the USB memory is displayed on the screen.

For details on the slideshow, refer to page 29. For details on adding images to the internal memory, refer to page 32.

Notes

When using a commercially available USB cable, use an A-Type USB cable that is less than 3 meters long.

Do not disconnect the USB memory or turn the photo frame off while the access lamp on the USB memory is flashing. Doing so may damage the data stored on the USB memory. Sony assumes no responsibility for any damage or loss of data.

A USB hub or USB device with a built-in USB hub may not work properly.

The photo frame cannot use data that has been encrypted or compressed using, for instance, fingerprint authentication or a password.

USB memory

48 GB

Using an external device (with Bluetooth)

U

sing an external device (w ith B

luetooth)

Transferring images using Bluetooth You can connect a Bluetooth adaptor (optional) to the USB A/Bluetooth connector of the photo frame and transfer images from a Bluetooth compatible mobile phone or other device. The transferred images are saved in internal memory.

Note

You cannot send a file to other Bluetooth compatible devices from the photo frame.

Compatible profiles for Bluetooth communication The DPF-D82/D92 supports the following profiles:

BIP (Basic Imaging Profile) Image Push Responder

OPP (Object Push Profile) Object Push Server

For the profiles that your Bluetooth device supports, please refer to its manual.

What is a Profile? A profile consists of the standards that enable Bluetooth wireless communication. There are several profiles available, depending on the purposes and product to be used. To make Bluetooth communication possible, the devices used in the communicated should support the same profile.

Compatible image file formats that can be displayed See page 64.

Maximum number of pixels that can be handled See page 64.

1 Connect the photo frame to the AC power source. (.page 18)

2 Turn the photo frame to ON. (.page 19)

3 Connect the Bluetooth adaptor (optional) to the USB A/Bluetooth connector.

is displayed on the upper portion of the screen when the guide is displayed.

Note

If any device, other than the Bluetooth adaptor, such as a memory card, camera, PC, or other USB memory device or a USB cable is connected to any of the memory card slots, or the USB A/Bluetooth connector, disconnect it from the photo frame and then connect the Bluetooth adaptor.

4 Check the Bluetooth address of the photo frame. You can display the address from [System Information]. (page 46)

Tip

The address is displayed only when the Bluetooth adaptor is connected.

5 Transfer an image from the Bluetooth-compliant mobile phone, or other device to the photo frame. The image transferred is saved on the internal memory.

Note

You cannot transfer an image to the memory card of a digital photo frame.

Continued

49 GB

To select the photo frame from a Bluetooth-compliant device, select Sony DPF-D92 ##, Sony DPF-D82 ##. (## stands for the two figures from the right of the address displayed in [System Information].)

When input of Passkey* is required Input 0000. You cannot change the Passkey with the photo frame.

* A Passkey is often referred to as a pass code or PIN code.

Notes

We cannot guarantee that this product works with all devices enabled with Bluetooth wireless technology.

Do not use the DPPA-BT1 outside the area you purchased it. Depending on the area, the use of this product may violate the local radio wave regulations and may be subject to penalty.

The communication distance of the product may vary depending on the obstacles between the product (a human body, metal objects, or a wall) and the mobile phone or other device.

The sensitivity of the Bluetooth communication may be affected under the following conditions:

When there is an obstacle between the product and the mobile phone or other product such as a human body, metal objects, or a wall.

Where a wireless LAN is established or a microwave oven is being used near-by, or other electromagnetic waves are emitted.

We cannot guarantee that this product works with all devices enabled with Bluetooth wireless technology.

Sony cannot assume any responsibility for any information leakage that may be caused by the use of Bluetooth communications.

Sony cannot accept responsibilities for any failure to satisfy the protection requirements resulting from a non-recommended modification or use of the product. For customer support information, please refer to the operating instructions of the photo frame.

P Caution Radio waves from a Bluetooth device may

adversely affect the operation of electrical and medical devices, and could lead to accidents due to malfunctions. Make sure to turn off the product and mobile phone and do not use this product in the following places:

Inside hospitals, trains, airplanes, gas stations or other places where flammable gas may be present.

near automatic doors or fire alarms or other automatically controlled devices.

near medical equipment.

Keep this product at least 22 cm away from cardiac pacemakers. Radio waves from this product may adversely affect the operation of cardiac pacemakers.

Bluetooth compatible mobile phone

50 GB

Using an external device (with a computer)

U

sing an external device (w ith a com

puter)

Connecting to a computer You can connect to a computer to view and copy images from the internal memory of the photo frame to the computer, and copy images from the computer to the photo frame.

To connect a computer to the picture frame, your computer must satisfy the following recommended system requirements.

x Windows Recommended OS: Microsoft Windows Vista SP1/Windows XP SP3/Windows 2000 Professional SP4

Port: USB port

x Macintosh Recommended OS: Mac OS X (10.4 or later)

Port: USB port

Notes

If multiple USB devices are connected to a computer or if a hub is used, a problem may occur. In such a case, simplify the connections.

You cannot operate the photo frame from another USB device being used simultaneously.

Do not disconnect the USB cable during data communication.

Operation with all computers that satisfy the recommended system requirements is not guaranteed.

The photo frame has been demonstrated as operable when connected to PC or Sony digital photo printer. When other devices are connected to the photo frame, these devices may not recognize the internal memory of the photo frame.

Note

This section shows an example for a connection for Windows Vista. Depending on the OS you use, the screen display and procedures may vary.

1 Connect the photo frame to the AC power source. (.page 18)

2 Connect the computer and photo frame with a commercially available USB cable.

Note

Use a B-Type USB cable that is less than 3 meters long.

3 Turn the photo frame to ON. (.page 19)

System requirements

Connecting to a computer to exchange images

To USB B connector

To USB connectorComputer

Continued

51 GB

4 When the [AutoPlay] window appears on the computer display, click [Open folder to view files]. If the [AutoPlay] window does not appear, click [Computer (My Computer)] in the Start menu, and then open the removable disc.

5 Move the cursor in this window and right click, and then click [New] - [Folder]. Name this new folder. In this manual, the folder name sony is used as an example.

6 Double click to open this sony folder.

7 Open the folder that contains the image files you want to copy, and then copy the image files by using drag-and-drop.

Notes

When saving images from a computer in the internal memory, make a folder in the internal memory and save the images in this folder. If you do not make a folder, you can only save up to 512 images. In addition, the number of images may be reduced depending on the file name length or character type.

A paticular image may not be displayed in order of the shooting date on the index image display, etc as the information on the shooting date may have been changed or lost when you edited or saved that image file on a computer.

When images from the computer are saved in the internal memory of the photo frame, the image files are saved without being compressed. As a result,

fewer images may be able to be saved to the internal memory of the photo frame.

Image files made or edited on a computer may not be displayed. Image files set to Read Only on a computer cannot be deleted on the photo frame. Cancel Read Only before saving image files from a computer on the photo frame.

Disconnect the USB cable or turn the photo frame to OFF after disconnecting it from your computer.

1 Double-click on the Task Tray.

2 Click (USB Mass Storage Device) t [Stop].

3 Click [OK] after checking the drive you want to remove.

Disconnecting your computer

52 GB

Error messages

E

rror m essages

If an error message appears If an error occurs, one of the following error messages may be displayed on the LCD screen of the photo frame. Follow the corresponding solution below to solve the problem.

Error message Meaning/Solutions

No Memory Stick. / No CompactFlash card. / No SD Memory Card. / No xD-Picture Card. / No External Device.

A memory card is not inserted in a slot. Or, an external device is not connected to the USB A/Bluetooth connector. Insert a memory card in the corresponding slot. Or, connect an external device. (.pages 21, 48)

An incompatible Memory Stick is inserted. / An incompatible CompactFlash card is inserted. / An incompatible SD Memory Card is inserted. / An incompatible xD- Picture Card is inserted. / An incompatible External Device is inserted.

An unsupported memory card is inserted. Or, an unsupported external device is connected to the USB A/Bluetooth connector. Use a memory card or external device that is supported by the photo frame.

No images on file. There is no image file that can be displayed on the screen of the photo frame on the memory card or the external device. Use a memory card or on external device containing image files that can be displayed with the photo frame.

Cannot delete a protected image. To delete a protected file, cancel the protection on your digital camera or computer.

Media is protected. Remove protection then try again.

The memory card is write-protected. Slide the write- protect switch to the enable position. (.page 62)

The Memory Stick is full. / The CompactFlash card is full. / The SD Memory Card is full. / The xD- Picture Card is full. / The External Device is full.

No more data can be saved because the memory card, the internal memory, or the external device is full. Delete images, or use a memory card or external device with free space available.

Continued

53 GB

Error reading the Memory Stick. / Error reading the CompactFlash card. / Error reading the SD Memory Card. / Error reading the xD-Picture Card. / Error reading the internal memory./ Error reading the External Device.

An error has occurred. If this error message is displayed frequently, check the status of the memory card or external device with a device other than the photo frame.

In the case of an external device: The external device may be write-protected. Cancel the write-protection setting for the device you are using. The internal memory of a digital camera may be write- protected.

For an internal memory: Initialize the internal memory.

Note

When you initialize the internal memory, please note that all the

image files added to the album are deleted.

Write error in the Memory Stick. / Write error in the CompactFlash card. / Write error in the SD Memory Card. / Write error in the xD-Picture Card. / Write error in the internal memory./ Write error in the External Device.

The Memory Stick is read only. A Memory Stick-ROM is inserted. To save the images, use the Memory Stick recommended.

The Memory Stick is protected. A protected Memory Stick is inserted. To edit and save the images, use an external device to remove protection.

Media format not supported. For a memory card, use your digital camera or other device to format the memory card.

For the internal memory, initialize it with the photo frame.

Note When you initialize the media, all the files on the media will be deleted.

Cannot open the image. The photo frame cannot display or open an image file whose format is not supported.

No more USB hubs can be connected.

Connect the device directly to the photo frame, or use a device without a built-in USB hub.

Incompatible USB device. Check devices USB settings.

Connect a device with support for mass storage. If the USB setting of your device is incorrect, set the mass storage mode in the USB setting.

Error message Meaning/Solutions

54 GB

Troubleshooting

T

roubleshooting

If trouble occurs Before submitting the photo frame for repair, try using the following guidance to solve the problem. If the problem persists, consult with your Sony dealer or Sony service facilities.

Power supply

Displaying images If the power is turned on but images are not displayed or the settings of the operation screen cannot be configured, confirm the following check items.

Symptom Check item Cause/Solutions

The power cannot be turned on.

Is the AC power plug inserted correctly?

c Insert the power plug properly.

Symptom Check item Cause/Solutions

No images are displayed on the screen.

Is a memory card inserted or an external device connected properly?

c Insert a memory card or connect an external device properly. (.pages 21, 49)

Does the memory card contain images saved with a digital camera or other device?

Are images stored on the external device?

c Insert a memory card containing images or connect an external device containing images.

c Check the file formats that can be displayed. (.page 64)

Is the file format compatible with DCF?

c A file that is not compatible with DCF may not be able to be displayed with the photo frame, even if it can be displayed with a computer.

Images are not played back in the order of shooting date.

Were these images saved from a computer?

Were these images edited on a computer?

c The information on the shooting date may be changed or lost when you edit or save an image file on a computer.

Continued

55 GB

Some images are not displayed.

Are the images displayed in the index view?

c If the image is displayed in the index view but cannot be displayed as single image, the image file may be damaged even though its thumbnail preview data is fine.

c A file that is not compatible with DCF may not be able to be displayed with the photo frame, even if it can be displayed with a computer.

Does the mark displayed below appear in the index view?

Were the images created with an application on a computer?

c If the mark shown on the left is displayed, the image file may not be supported by the photo frame because, for example, it is a JPEG file that was created with your computer. Also, the image file may be supported, but not contain thumbnail data. Select the mark and press to change the screen to the single image display. If the mark on the left is displayed again, the image cannot be displayed because the image file is not supported by the photo frame.

Does the mark displayed below appear in the index view?

c If the mark shown on the left is displayed, the image file is supported by the photo frame, but the thumbnail data or image itself cannot be opened. Select the mark and press . If the mark shown on the left is displayed again, the image cannot be displayed.

Are there more than 9,999 images in the memory card or external device?

c The photo frame can play, save, delete, or otherwise handle up to 9,999 image files.

Did you rename the file with a computer or other device?

c If you named or renamed the file on your computer and the file name includes characters other than alphanumeric characters, the image may not be able to be displayed on the photo frame.

Is there a folder with more than 8 levels in its hierarchy on the memory card or in the external device?

c The photo frame cannot display images saved in a folder that is more than eight levels deep.

Symptom Check item Cause/Solutions

56 GB

T roubleshooting

Saving and deleting images

The file name is not displayed properly.

Did you rename the file with a computer or other device?

c If you named or renamed the file on your computer and the file name includes characters other than alphanumeric characters, the file name may not be able to be displayed properly on the photo frame. Also, for a file created on a computer or other device, a maximum of ten characters from the beginning of the file name can be displayed.

Note Only alphanumeric characters can be displayed.

Blank areas appear at the top and bottom.

Is the image extremely tall or wide?

c If an image is extremely tall or wide, blank areas may appear because of the ratio between the height and width.

Symptom Check item Cause/Solutions

Cannot save an image.

Is the memory card write- protected?

c Cancel write-protection and try saving again.

Is the write-protect switch of the memory card in the [LOCK] position?

c Slide the write-protect switch to the enable position.

Is the memory card full? c Replace the memory card with one with sufficient free space. Or, delete any unwanted images. (.page 36)

Is the internal memory full? c Delete any unwanted images. (.page 36)

Did you save images from a computer to the internal memory without making a folder in the internal memory?

c If you do not make a folder, you can only save up to 512 images. In addition, the number of images may be reduced depending on the file name length or character type. When you save images in the internal memory from a computer, be sure to make a folder in the internal memory and save the images in this folder.

Symptom Check item Cause/Solutions

Continued

57 GB

Connecting a external device

Photo frame

Cannot delete an image.

Is the memory card write- protected?

c Use the device you are using to cancel write-protection and try deleting again.

Is the write-protect switch of the memory card in the [LOCK] position?

c Slide the write-protect switch to the enable position.

Are you using a Memory Stick-ROM?

c It is not possible to delete an image from or format a Memory Stick-ROM.

Is this image protected? c Check the image information from the single view mode. (.page 28)

c An image with a mark is set to Read Only. You cannot delete it on the photo frame.

An image was deleted accidentally.

c An image cannot be recovered once it is

deleted.

Symptom Check item Cause/Solutions

Nothing happens even if the USB cable is disconnected and then re-connected.

c An over current error may have occurred with the photo frame. To recover from the error, turn the power of the photo frame off and then back on.

Symptom Check item Cause/Solutions

Nothing happens even if you operate the photo frame.

c Push the reset switch on the back of the photo frame using a long, thin object such as a pin, etc. (.page 12)

c Set the power switch to off, and then set it to on again. (.page 12)

Symptom Check item Cause/Solutions

58 GB

T roubleshooting

Remote control

Symptom Check item Cause/Solutions

Nothing happens even if you operate the remote control.

Is the battery inserted in the remote control properly?

c Replace the battery. (.page 15) c Insert a battery. (.page 15) c Insert a battery in the proper orientation.

(.page 15)

c Point the top end of the remote control towards the remote sensor on the photo frame. (.page 15)

c Remove any obstruction between the remote control and the remote sensor.

Is there a protective sheet inserted?

c Remove the protective sheet. (.page 15)

59 GB

Additional information

Precautions

Be careful not to set or drop any heavy objects on the power cord, or to damage the power cord in any way. Never operate this photo frame with a damaged power cord.

Should any solid object or liquid fall into the cabinet, unplug the photo frame and have it checked by qualified personnel before operating it any further.

Never disassemble the photo frame. To disconnect the power cord, pull it out by

the plug. Never pull the power cord itself. When the photo frame is not going to be

used for an extended period of time, disconnect the power cord from the wall outlet.

Do not handle the photo frame roughly. To reduce the risk of electrical shock, always

unplug the photo frame from the electrical outlet before cleaning and servicing the photo frame.

Avoid placing the photo frame in a location subject to: vibration humidity excessive dust direct sunlight extremely high or low temperatures

Do not use electrical equipment near the photo frame. The photo frame will not work properly in electromagnetic fields.

Do not place heavy objects on the photo frame.

On the AC adaptor Even if your photo frame is turned off, AC

power (house current) is still supplied to it

while it is connected to the wall outlet via the AC adaptor.

Be sure to use the AC adaptor supplied with the photo frame. Do not use other AC adaptors, as this may cause a malfunction.

Do not use the supplied AC adaptor for other devices.

Do not use an electrical transformer (travel converter), as this may cause overheating or a malfunction.

In case the cord of the AC adaptor is damaged, do not use it any longer, as this may be dangerous.

On moisture condensation If the photo frame is brought directly from a cold location to a warm location or placed in an extremely warm or humid room, moisture may condense inside the unit. In such cases the photo frame will probably not work properly and may even develop a fault if you persist in using it. If moisture condensation occurs, unplug the AC adaptor of the photo frame and do not use the photo frame for at least one hour.

On transport When you transport the photo frame, remove the memory card, external devices, AC adaptor, and connected cables from the photo frame and put the photo frame and its peripherals in the original box with the protective packaging.

If you no longer have the original box and packing parts, use similar packing material so that the photo frame will not be damaged while being transported.

Clean the photo frame with a soft dry cloth, or a soft cloth lightly moistened with a mild detergent solution. Do not use any type of solvent, such as alcohol or benzine, which may damage the finish.

Safety

Installation

Cleaning

60 GB

A dditional inform

ation

TV programs, films, video tapes, portraits of other people, or other materials may be copyrighted. Unauthorized use of such materials may infringe the provisions of the copyright law.

Even if you perform [Format internal memory], the data in the internal memory may not be erased completely. When you dispose of the photo frame, we recommend that you physically destroy the photo frame.

About memory cards

Types of Memory Stick that the photo frame can use With the photo frame, you can use the following types of Memory Stick*1:

*1 The photo frame supports FAT32. The photo frame has been demonstrated as operable with a Memory Stick with a capacity of 16 GB or less manufactured by Sony Corporation. However, we do not guarantee the operations of all the Memory Stick media.

*2 The photo frame is equipped with a slot compatible with both standard-size and Duo-size media. Without a Memory Stick Duo adaptor, you can use both a standard-size Memory Stick and the compact-size Memory Stick Duo.

*3 When using a Memory Stick Micro with the photo frame, always insert it into an M2 adaptor.

*4 M2 is an abbreviation for Memory Stick Micro. In this section, M2 is used to describe a Memory Stick Micro.

*5 Data reading/recording that requires MagicGate copyright protection cannot be performed. MagicGate is the general name of a copyright

Restrictions on duplication

Disposing of the photo frame

Memory Stick

Type of Memory Stick

Displaying Deleting/ Saving

Memory Stick*2

(Not compatible with MagicGate)

OK OK

Memory Stick*2

(Compatible with MagicGate)

OK*5 OK*5

MagicGate Memory Stick*2 OK*5 OK*5

Memory Stick PRO*2 OK*5 OK*5

Memory Stick PRO-HG*2 OK*5*6 OK*5*6

Memory Stick Micro*3 (M2*4)

OK*5 OK*5

Continued

61 GB

protection technology developed by Sony using authentication and encryption.

*6 The photo frame does not support 8 bit parallel data transfer.

Notes on use For the latest information on the Memory

Stick types that the photo frame supports, see the Memory Stick compatibility information on the Sony web site: http://www.memorystick.com/en/support/ support.html (Select the area where you use your photo frame, and then select Digital Photo Frame from each area page.)

Do not insert more than one Memory Stick at the same time, or this may cause trouble with the photo frame.

If you use a Memory Stick Micro with the photo frame, the Memory Stick Micro needs to be inserted into an M2 adaptor.

If you insert a Memory Stick Micro into the photo frame without an M2 adaptor, you may be unable to remove the Memory Stick Micro.

If you insert a Memory Stick Micro into an M2adaptor, and insert the M2 adaptor into a Memory Stick Duo adaptor, the photo frame may not operate properly.

When you initialize a Memory Stick, use the initialization function of your digital camera. If you initialize it with your computer, images may not be displayed properly.

When you perform initialization, all the protected images are erased. To avoid erasing important data by accident, make sure to check the contents of the Memory Stick before initialization.

You cannot record, edit, or delete data if you slide the write-protect switch to LOCK.

Do not attach any other material than the supplied label on the labelling position. When you attach the supplied label, be sure to attach it to the labelling position. Be careful that the label does not stick out.

The SD memory card slot of the photo frame allows you to use the following:

SD memory card*1

miniSD card, microSD card (An adaptor is necessary.)*2

SDHC memory card*3

MMC standard memory card*4

We do not guarantee proper operations for all types of SD memory cards and MMC standard memory cards. *1 The photo frame has been demonstrated as

operable with an SD memory card with a capacity of 2 GB or smaller.

*2 Some commercially available card adaptors have projected terminals on the back. This type of adaptor may not work properly with the photo frame.

*3 The photo frame has been demonstrated as operable with an SDHC memory card with a capacity of 32 GB or less.

*4 The photo frame has been demonstrated as operable with an MMC standard memory card with a capacity of 2 GB or less.

Notes on use Data reading/recording that requires copyright protection cannot be performed.

With the xD-Picture Card slot of the photo frame, you can use an xD-Picture Card*5. Not all the memory card operations are supported and we do not guarantee proper operations for all types of xD-Picture Card. *5 The photo frame has been demonstrated as

operable with an xD-Picture Card with a capacity of 2 GB or less.

The CompactFlash card slot of the photo frame allows you to use the following:

SD memory card

xD-Picture Card

CompactFlash card

62 GB

A dditional inform

ation

CompactFlash Memory Card (Type I/ Type II) and CF+Card (Type I/Type II)- compatible CompactFlash Card*6

Microdrive You can also use the Smart Media card by using a commercially available CompactFlash card adaptor*7.

However, we do not guarantee proper operations for all types of CompactFlash cards. *6 Use a CompactFlash card with a power

specification of 3.3V or 3.3V/5V. You cannot use a type for 3V or 5V only. Do not insert other types of CompactFlash card into the photo frames insertion slot. The photo frame may be damaged. The photo frame has been demonstrated as operable with a CompactFlash with a capacity of 32 GB or smaller.

*7 When using a commercially available CompactFlash card adaptor, refer to the operating instructions of the adaptor you use for how to install the card and adaptor. When using a CompactFlash card adaptor, a write-protected card may not work properly.

When using a card, make sure to check the correct insertion direction of the card and the correct insertion slot.

When inserting the memory card, it will only insert part of the way, so do not try to force it, as this could damage the memory card and/or photo frame.

Do not remove a card or turn off the photo frame while the photo frame is reading or writing data, or the access indicator is flashing. Otherwise, data may be rendered unreadable or be erased.

We recommend that you save a backup of important data.

Data processed with the computer may not be displayed with the photo frame.

When you carry or store a card, put it in the case supplied with it.

Do not touch the terminal of a card with your hand or a metal object.

Do not strike, bend or drop a card.

Do not disassemble or modify a card. Do not expose a card to water. Do not use or store a card under the

following conditions: Locations beyond the required operational

conditions including locations such as the hot interior of a car parked in the sun and/ or in the summer, the outdoors exposed to direct sunlight, or a place near a heater.

Humid locations or locations with corrosive substances present

Locations subject to static electricity or electrical noise

Notes on using a memory card

63 GB

D:\DPF series\V Series\4129231131\4129231131\4129231131DPFD92CED\01GB-DPFD92CED\100ADD.fm Master: Left

Specifications

x Photo frame

Image file name DCF format, 256 characters within 8th

hierarchy

Maximum number of files that can be

/an external

an be saved.) pacity, 1 GB rtion of agement.

)

mm )

mm

ging on the

mm s)

mm )

ncluding the C adaptor

11.6W

5.5W

s a status ideshow using y with the emory card or

100ADD.fm Page 64 Wednesday, April 8, 2009 9:04 AM

64 GB

LCD screen LCD panel:

DPF-D92: 9.0 inches, TFT active matrix DPF-D82: 8.0 inches, TFT active matrix

Total number of dots: DPF-D92/D82: 1,152,000 (800 3(RGB) 480) dots

Display aspect ratio 15:9

Effective display area DPF-D92: 8.6 inches DPF-D82: 7.6 inches

LCD backlight life DPF-D92/D82: 20,000 hours (before brightness of the backlight is

reduced to half)

Input/Output connectors USB connector (TypeB, Hi-Speed USB) USB A/Bluetooth connector

(TypeA, Hi-Speed USB) Slots

Memory Stick PRO slot SD memory card/MMC/ xD-Picture Card slot CompactFlash card/Microdrive slot

Compatible image file formats JPEG: DCF 2.0 compatible, Exif 2.21

compatible, JFIF*1

RAW (preview only*2): SRF, SR2, ARW (2.0 or lower version)

(Some image file formats are not compatible.)

Maximum number of pixels that can be displayed

8,000 (H) 6,000 (V) pixels

File system FAT12/16/32,

sector size of 2,048 bytes or smaller

handled 9,999 files for a memory card

device

Internal memory capacity*3

DPF-D92/D82: 1 GB (Approx. 2,000 images*4 c When measuring media ca equals 1 billion bytes, a po which is used for data man

Power requirements DC IN jack, DC 12V

Power consumption

Operating temperature 5 C to 35 C (41 F to 95 F

Dimensions

[With the stand spread out] DPF-D92:

Approx. 276 189 144.1 (10 7/8 7 1/2 5 3/4 inches (width/height/depth)

DPF-D82: Approx. 243 162 126.6 (9 5/8 6 1/2 5 inches)

[When the photo frame is han wall]

DPF-D92: Approx. 276 189 39.5 (10 7/8 7 1/2 1 9/16 inche (width/height/depth)

DPF-D82: Approx. 243 162 39.5 (9 5/8 6 1/2 1 9/16 inches

Model in operation mode i A

DPF-D92/ D82

at the maximum load

normal mode*

* The definition of the normal mode i which allows the performance of a sl images stored in the internal memor default settings without inserting a m connecting an external device.

DPF-D82/D92 4-129-231-13 (1)

A dditional inform

ation

Mass DPF-D92: Approx. 810 g (1 lb 12 5/8 oz) DPF-D82: Approx. 720 g (1 lb 9 3/8 oz) (excluding the AC adaptor)

Included accessories See Checking included items on

page 11.

x AC adaptor The following are common specifications of DPF-D92/D82.

Power requirements - 100 V to 240 V, 50/60 Hz 0.48 A

Rated output voltage 12 V 1.2 A

Dimensions Approx. 34 72 69 mm (1 3/8 2 7/8 2 3/4 inches) (width/height/depth) (excluding the protruding parts)

Mass Approx. 110 g (4 oz)

See the label of AC adaptor for more details.

Design and specifications are subject to change without notice.

*1: Baseline JPEG with 4:4:4, 4:2:2, or 4:2:0 format *2: RAW files are displayed as thumbnail preview. *3: The capacity is calculated as 1 GB is equivalent to

1 000 000 000 bytes. The actual capacity is reduced as files for management and applications are included. Approximately 900 MB on DPF- D92/D82 can be used for your actual operation.

*4: Approximate number is shown when the images taken by 2 000 000 pixels equivalent camera are saved. The value may vary depending on the shooting condition.

Customer support home page The latest support information is available at the following home page address:

http://www.sony.net/

65 GB

66 GB

Index

A AC adaptor 18

Accessories 11

Adding to the internal memory 32

Alarm 43, 46

Associated file 28

Auto power ON/OFF 46

Auto power on/off 42

B Bluetooth 49

C Calendar 21

Changing the settings 44

Cleaning 60

Connecting

Computer 51

External device 48

Connecting to the AC power source 18

D Date/time settings 20, 46

DC IN 8.4 V 18

Deleting an image 36

Display priority 22

E Error messages 53

Exporting an image 34

F Features 9

Format internal memory 47

G General Settings 46

I Image file size 46

Index image display 27

Initialize 47

L Language setting 47

M Mass storage compatible devices 48

Memory cards 61

Memory Stick 61

CompactFlash card 62

Notes on use 63

SD memory card 62

xD-Picture Card 62

P Placing in portrait or landscape orientation 16

Playback device 40

Precautions 60

R Remote control 15

Replacing the battery of the remote control 15

Reset 47

Rotating an image 41

S Searching for an image 39

Setting the stand 16

Single view mode 26

Slideshow display 24

Slideshow Settings 31

Color effect 31

Display Mode 31

Effect 31

Interval 31

Shuffle 31

Specifications 64

System Information 47

System requirements

Macintosh 51

Windows 51

T Troubleshooting 55

U USB cable 48

W Write-protect switch 62

Z Zooming an image

Manualsnet FAQs

If you want to find out how the DPF D92 Sony works, you can view and download the Sony DPF D92 Operating Instruction on the Manualsnet website.

Yes, we have the Operating Instruction for Sony DPF D92 as well as other Sony manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Operating Instruction should include all the details that are needed to use a Sony DPF D92. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Sony DPF D92 Operating Instruction is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Sony DPF D92 Operating Instruction consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Sony DPF D92 Operating Instruction free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Sony DPF D92 Operating Instruction, simply download the document to your computer. Once downloaded, open the PDF file and print the Sony DPF D92 Operating Instruction as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.