Contents

Sony AIR SA20PK Operating Instruction PDF

1 of 44
1 of 44

Summary of Content for Sony AIR SA20PK Operating Instruction PDF

2008 Sony Corporation

AIR-SA20PK

Wireless Audio System

AIR-SA20PK.GB.4-117-793-12(1)

Operating Instructions

4-117-793-12(1)

AIR-SA20PK.GB.4-117-793-11(1)

GB

WARNING To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. To reduce the risk of fire, do not cover the ventilation opening of the apparatus with newspapers, tablecloths, curtains, etc. Do not place the naked flame sources such as lighted candles on the apparatus. To reduce the risk of fire or electric shock, do not expose this apparatus to dripping or splashing, and do not place objects filled with liquids, such as vases, on the apparatus. As the main plug is used to disconnect the unit from the mains, connect the unit to an easily accessible AC outlet. Should you notice an abnormality in the unit, disconnect the main plug from the AC outlet immediately. The unit is not disconnected from the mains as long as it is connected to the AC outlet, even if the unit itself has been turned off. Do not install the appliance in a confined space, such as a bookcase or built-in cabinet. Do not expose batteries or apparatus with battery-installed to excessive heat such as sunshine, fire or the like. The nameplate is located on the bottom exterior.

Notice for the customers in the U.S.A.

This symbol is intended to alert the user to the presence of uninsulated dangerous voltage within the products enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

AIR-SA15Ti: The following indications are located on the AC power supply unit.

AIR-SA15R: The following indications are located on the bottom exterior.

AIR-SA20PK.GB.4-117-793-11(1)

GB

Owners Record The model and serial numbers are located on the bottom of the unit. Record these numbers in the space provided below. Refer to them whenever you call upon your Sony dealer regarding this product. Model No. Serial No.

Important Safety Instructions 1) Read these instructions. 2) Keep these instructions. 3) Heed all warnings. 4) Follow all instructions. 5) Do not use this apparatus near water. 6) Clean only with dry cloth. 7) Do not block any ventilation openings.

Install in accordance with the manufacturers instructions.

8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

9) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10) Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11) Only use attachments/accessories specified by the manufacturer.

12) Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

13) Unplug this apparatus during lightning storms or when unused for long periods of time.

14) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

Continued

AIR-SA20PK.GB.4-117-793-12(1)

GB

The following FCC statement applies only to the version of this model manufactured for sale in the U.S.A. Other versions may not comply with FCC technical regulations.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving

antenna. Increase the separation between the

equipment and receiver. Connect the equipment into an outlet

on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

CAUTION You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment.

For the wireless transceiver (EZW-RT10/ EZW-RT10A) This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment must not be co-located or operated in conjunction with any other antenna or transmitter. This equipment complies with FCC radiation exposure limits set forth for uncontrolled equipment and meets the FCC radio frequency (RF) Exposure Guidelines in Supplement C to OET65. This equipment should be installed and operated with at least 20cm and more between the radiator and persons body (excluding extremities: hands, wrists, feet and ankles).

AIR-SA20PK.GB.4-117-793-12(1)

GB

Notice for the customers in Canada For the wireless transceiver (EZW-RT10/ EZW-RT10A) This device complies with RSS-Gen of IC Rules. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. This equipment complies with IC radiation exposure limits set forth for uncontrolled equipment and meets the RSS-102 of the IC radio frequency (RF) Exposure rules. This equipment should be installed and operated with at least 20cm and more between the radiator and persons body (excluding extremities: hands, wrists, feet and ankles).

S-AIR and its logo are trademarks of Sony Corporation.

iPod is a trademark of Apple Inc., registered in the U.S. and other countries.

The Bluetooth word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by Sony Corporation is under license. Other trademarks and trade names are those of their respective owners.

All other trademarks and registered trademarks are of their respective holders. In this manual, and marks are not specified.

AIR-SA20PK.GB.4-117-793-11(1)

GB

AIR-SA20PK.GB.4-117-793-11(1)

GB

Table of Contents

Others

Troubleshooting.................................34 Messages...............................................38 Precautions...........................................38 Specifications.......................................40 Compatible.iPod.models.................42 Index.......................................................43

Features.................................................... 8 Unpacking............................................... 9 Guide.to.parts.and.controls............10

Getting Started

Hooking.up.the.system....................18 Establishing.the.S-AIR.. connection............................................20 Setting.the.clock.of.the.sub.. units.........................................................23

Operations

Selecting.the.S-AIR.mode................24 Listening.to.iPod.music.using.the. S-AIR.connection................................25 Listening.to.the.radio.using.the.. S-AIR.connection................................27 Presetting.radio.stations..................28 Using.an.optional.AV.system..........29 Changing.the.display........................30 Using.the.Timers.................................31 Turning.off.the.remote.control. function.of.the.sub.units..................33 Changing.the.illumination. brightness.of.the.main.unit............33

AIR-SA20PK.GB.4-117-793-12(1)

GB

Features The AIR-SA20PK is an S-AIR compatible packaged product that consists of one S-AIR main unit AIR-SA15Ti and two S-AIR sub units AIR-SA15R. Connecting the S-AIR main unit (hereafter called Main unit) with the S-AIR sub units (hereafter called Sub units) using S-AIR technology, you can use each unit in a remote location. For example, you can install the sub units, one in the study room and the other in the bedroom, and then install the main unit in the living room. You can then listen to the music from the main unit located in the living room by controlling the sub units. You can also connect the main unit to an optional AV system (such as a TV), and on this optional AV system you can enjoy audio, video and photo contents of an iPod which is connected to the main unit.

Main unit and iPod

Bedroom

Sub unit

Study room

Sub unit

Living room

AV system

S-AIR (Sony Audio Interactive Radio frequency) Recent times have seen the rapid spread of DVD media, Digital Broadcasting, and other high-quality media. To ensure that the subtle nuances of these high-quality media are transmitted with no deterioration, Sony has developed a technology called S-AIR for the radio transmission of digital audio signals with no compression, and has incorporated this technology into the EZW-RT10/EZW-RT10A. This technology transfers digital audio signals with no compression using the 2.4 GHz band range of ISM band (Industrial, Scientific, and Medical band), such as wireless LANs and Bluetooth applications.

AIR-SA20PK.GB.4-117-793-12(1)

GB

Unpacking Check that you have all the following items.

Main unit Main unit (AIR-SA15Ti) (1)

Wireless transceiver (EZW-RT10 or EZW-RT10A) (1)*

Remote (RM-ANU045) (1)

R03 (size AAA) batteries (2)*

FM lead antenna (1) One of the following two antennas is supplied.

or

AM loop antenna (1)

iPod Dock Adapters (1 set)

Sub unit Sub unit (AIR-SA15R) (2)

Wireless transceiver (EZW-RT10 or EZW-RT10A) (2)*

Remote (RM-ANU046) (2)

R03 (size AAA) batteries (4)*

Others Operating Instructions (this manual) (provided in each language)

Warranty (1 for customers in the USA, 1 for customers in Canada) For customers in the USA Use LIMITED WARRANTY card warranted by Sony Electronics Inc. For customers in Canada Use Consumer 1 Year Warranty card warranted by Sony of Canada Ltd.

* The same type of wireless transceivers and batteries are used for the main unit and the sub units.

AIR-SA20PK.GB.4-117-793-11(1)

10GB

Guide to parts and controls Main unit (AIR-SA15Ti/Wireless Audio Transmitter)

Front panel

Rear panel

AIR-SA20PK.GB.4-117-793-11(1)

11GB

G uide.to.parts.and.controls

Remote for the main unit (RM-ANU045)

ILLUMINATION.(33) Press to change the illumination brightness.

BAND.(27) Press to select FM or AM reception mode.

SYSTEM.MENU.(22,.25,.28,.37) Press to enter the system menu.

POWER.indicator.(20) Lights up when the main unit is turned on.

iPod.connector.(19,.25,.29) Place an iPod on the connector to listen to audio contents stored in the iPod. You need to connect the supplied iPod Dock Adapter first to use an iPod. For details on the supplied iPod Dock Adapters, refer to the instructions supplied with the iPod Dock Adapters.

S-AIR.indicator Lights up when the main unit is turned on with the supplied wireless transceiver inserted.

Unit:.TUNING/SELECT.+/.(22,. 25,.27,.28,.37) Press to tune in the desired station. Press to select a menu item. Remote:.TUNING.+/.(27,.28) Press to tune in the desired station.

ENTER.(22,.25,.28,.37) Press to enter the settings.

Illumination.(33) You can change the brightness using ILLUMINATION .

Continued

AIR-SA20PK.GB.4-117-793-11(1)

1GB

Display.(13)

Remote.sensor

ANTENNA.jacks.(18,.19) Connect the supplied FM lead antenna and AM loop antenna.

POWER.switch.(20,.34) Switch for turning the main unit on or off.

iPod.AUDIO.OUT.L/R.jacks.(29) iPod.VIDEO.OUT.jack.(29) Connect an optional AV system, such as a TV, etc.

S-AIR.ID.selector.(19,.20) Select the S-AIR ID to connect with the sub units.

PAIRING.button.(22) Press to perform pairing.

EZW-RT10.slot.(19) Insert the supplied wireless transceiver.

Buttons.for.controlling.an.iPod .(play/pause).(26) Press to start or pause playback.

/.(26) Press to skip to the previous/next track. Hold down to find a point in a track.

MENU.(26) Press to return to the previous menu. Works much like the Menu button on the iPod.

/.(26) Press to select a menu item or track for playback.

ENTER.(26) Press to execute the selected item or play the selected track.

PARTY.CH.(25,.27,.29) Press to select the sound source when the S-AIR mode is set to PARTY.

S-AIR.MODE.(25) Press to select the S-AIR mode.

Battery.compartment.lid.(20)

AIR-SA20PK.GB.4-117-793-11(1)

1GB

G uide.to.parts.and.controls

PRESET.+/.(29) Press to select a preset station.

DISPLAY.(25,.30) Press to view the information on the display.

Display

S-AIR.mode.indicator.(25)

PAIRING.indicator.(21)

Text.information

Tuner.reception.mode.(27) Tuner.reception.(27)

Continued

AIR-SA20PK.GB.4-117-793-11(1)

1GB

Sub unit (AIR-SA15R/Wireless Speaker System)

Front panel

Rear Panel

AIR-SA20PK.GB.4-117-793-11(1)

15GB

G uide.to.parts.and.controls

Remote for the sub unit (RM-ANU046)

.(power).(20,.32,.37) Press to turn on or off the sub unit.

STANDBY.indicator.(34) Lights up when the sub unit is turned off .

S-AIR.CH.(26,.28,.29) Press to select the S-AIR channel of the connected main unit.

.(play).(26,.32) Press to start or pause playback of an iPod connected to the main unit.

.(pause).(26) Press to pause or start playback of an iPod connected to the main unit.

/CANCEL.(stop/cancel).(26,.37) Press to pause playback of an iPod connected to the main unit.

/.(23,.26,.31) Press to skip to the previous/next track of an iPod connected to the main unit. Hold down to find a point in a track of an iPod connected to the main unit.

PRESET.+/.(29) Press to select a preset station.

DISPLAY.(30,.33,.37) Press to display the information of the connected main unit or clock in the display.

SLEEP.(31) Press to set the Sleep Timer.

Continued

AIR-SA20PK.GB.4-117-793-11(1)

1GB

CLOCK.TIMER/MENU.(23,.31) CLOCK.TIMER/ENTER.(23,.31,.33) Press to set the clock and the Daily Timer.

VOLUME.+/.(26,.31,.33) Press to adjust the volume.

S-AIR.indicator.(21) Lights up while the sub unit is connected to the main unit. Flashes when the sub unit is not connected to the main unit.

Remote.sensor

Display.(17)

.(headphones).jack Connect optional headphones.

S-AIR.ID.selector.(19,.20) Select the same S-AIR ID as the main unit.

PAIRING.button.(22) Press to perform pairing.

EZW-RT10.slot.(19) Insert the supplied wireless transceiver.

Battery.compartment.lid.(20)

AIR-SA20PK.GB.4-117-793-11(1)

1GB

G uide.to.parts.and.controls

Display

Timer.indicator.(31)

Text.information

Wireless.strength Indicates the S-AIR signal strength.

Play/Pause

PAIRING.indicator.(21)

AIR-SA20PK.GB.4-117-793-11(1)

1GB

Getting Started

Hooking up the system Main unit

Sub unit

AM loop antenna FM lead antenna (Extend it horizontally.) White side for North American model Brown side for other models Wireless transceiver

Wall socket

Wall socket

or

AIR-SA20PK.GB.4-117-793-12(1)

19GB

G etting Started

Continued

Wireless transceiver Insert the supplied wireless transceiver (EZW-RT10 or EZW-RT10A) securely into the EZW-RT10 slot on the rear panel of each unit. Check the orientation of the mark when inserting the supplied wireless transceivers (EZW-RT10 or EZW- RT10A). Failure to do so may result in damage to the unit.

Notes Make sure to turn off the main unit and the

sub units when inserting or removing the supplied wireless transceivers (EZW-RT10 or EZW-RT10A). Failure to do so may result in damage to the unit.

Do not touch the terminals of the supplied wireless transceivers (EZW-RT10 or EZW- RT10A).

Do not insert any device other than the supplied wireless transceivers (EZW-RT10 or EZW-RT10A) into the EZW-RT10 slot.

S-AIR ID selector Set the same S-AIR ID for the main unit and the sub units. For details on setting the S-AIR ID, see Establishing the S-AIR connection (page 20).

FM/AM antennas Find a location and an orientation that provide good reception, and then set up the antenna. Keep the antennas away from the power supply cord to avoid picking up noise.

Power Connect the power supply cord and the power cord to a wall socket.

To use the iPod Insert an iPod Dock Adapter into the iPod connector on the main unit before use. For details on the supplied iPod Dock Adapters, refer to the instructions supplied with the Dock Adapters.

To remove the iPod Dock Adapter, pull it up with your fingernail or a flat object using the slot inside the adapter.

Slot

AIR-SA20PK.GB.4-117-793-11(1)

0GB

To use the remote Slide and remove the battery compartment lid, and insert the two supplied R03 (size AAA) batteries, side first, matching the polarities shown below.

Remote for the main unit (RM-ANU05)

Remote for the sub unit (RM-ANU0)

Notes on using the remote With normal use, the batteries should last for

about six months. Do not mix an old battery with a new one or

mix different types of batteries. If you do not use the remote for a long period

of time, remove the batteries to avoid damage from battery leakage and corrosion.

Establishing the S-AIR connection You can easily establish the connection by setting the same S-AIR ID for the main unit and the sub units.

1 Check.that.the.wireless. transceivers.are.inserted. securely.to.the.main.unit.and. the.sub.units.(page.19).

2 Turn.on.the.main.unit.and.the. sub.units.

Main.unit Set the POWER switch on the rear panel to ON. The POWER indicator on the unit lights up.

Sub.units Press .

3 Set.the.same.S-AIR.ID.for.the. main.unit.and.the.sub.units.

Main.unit Set the S-AIR ID selector on the rear panel to the desired S-AIR ID.

Sub.units Set the S-AIR ID selector on the rear panel to the same S-AIR ID as the main unit.

Tip The S-AIR ID is set at the factory to A.

AIR-SA20PK.GB.4-117-793-11(1)

1GB

G etting.Started

Continued

4 Confirm.the.connection.status. Once the connection between the main unit and the sub units is established, the S-AIR indicators on the sub units light up and LINKED appears in the displays of the sub units for about 2 seconds.

Tip Up to 10 sub units (sold separately) can be connected with the main unit.

Identifying the main unit with a specific sub unit (Pairing operation)

It is easy to set the same S-AIR ID for the main unit and the sub units to establish the connection. However, if a neighbor has an S-AIR main unit with the same S-AIR ID as your S-AIR main unit, you may be able to hear the audio transmitted from your neighbors S-AIR main unit on your system. To prevent this, you can identify the main unit with a specific sub unit by performing the pairing operation.

Before pairing The connection is established by the S- AIR ID (example).

Your system Neighboring system

ID A

Main unit

ID A

Sub unit

ID A

Sub unit

After pairing The connection is established between the paired main unit and sub unit.

Your system Neighboring system

Pairing

ID A

Main unit

ID A

Sub unit

ID A

Sub unit

AIR-SA20PK.GB.4-117-793-11(1)

GB

1 Place.the.sub.unit.to.be.paired. near.the.main.unit. Pair the main unit with the sub units one at a time.

2 Check.that.the.power.of.the. main.unit.and.the.sub.unit.are. turned.on.

3 Check.that.the.S-AIR.ID.of.the. main.unit.is.the.same.as.the.S- AIR.ID.of.the.sub.unit.

4 Press.the.PAIRING.buttons.on. the.rear.panel.of.the.main.unit. and.the.sub.unit.using.a.pointed. object. When pairing is performed, the displays on both the main unit and the sub unit change as follows: PAIRING COMPLETE

To cancel pairing Change the S-AIR IDs of the main unit and the sub unit to different S-AIR IDs.

To stop the pairing operation midway Press the PAIRING button again.

To pair the main unit with multiple sub units Repeat steps 1 through 4.

If the S-AIR connection is unstable

Since the S-AIR product uses radio waves that share the same frequency (2.4 GHz) as other wireless systems, such as wireless LAN or Bluetooth devices, interference or poor transmission may result if you use other wireless systems near the main unit and/or the sub units. In this case, the connection may be improved by changing the RF CHANGE (Radio Frequency Change) setting on the main unit.

1 Press.SYSTEM.MENU.on.the.unit.

2 Press.TUNING/SELECT.+/.on. the.unit.repeatedly.until.RF. CHG.appears,.then.press.ENTER. on.the.unit.

3 Press.TUNING/SELECT.+/.on. the.unit.repeatedly.to.select.the. desired.setting. The default setting is underlined.

AUTO: Normally select this setting. The main unit changes the RF CHANGE setting to ON or OFF automatically.

ON: The main unit transmits sound by searching for the best channel for transmission.

OFF: The main unit transmits sound using a fixed channel for transmission. When you select this setting, select the S-AIR ID that provides the best connection.

AIR-SA20PK.GB.4-117-793-11(1)

GB

G etting.Started

4 Press.ENTER.on.the.unit.to.exit. the.system.menu. Setting the clock of the

sub units Use buttons on the unit to set the clock.

1 Press./.to.turn.on.the.unit.

2 Select.the.clock.set.mode. Press CLOCK/TIMER MENU. If the current mode appears on the display, press / repeatedly to select CLOCK, and then press CLOCK/ TIMER ENTER.

3 Set.the.time. Press / repeatedly to set the hour, and then press CLOCK/TIMER ENTER. Use the same procedure to set the minute.

Note The clock settings are canceled when you disconnect the power cord or if a power failure occurs.

AIR-SA20PK.GB.4-117-793-11(1)

GB

Operations

Selecting the S-AIR mode When connecting to multiple sub units, you can listen to different sound sources on each sub unit (MULTI SOURCE mode) or to the same sound source on both sub units (PARTY mode) by selecting the S-AIR mode accordingly. Use the main unit to set the S-AIR mode.

MULTI SOURCE mode

Main unit and iPod

Bedroom

Sub unit

Study room

Sub unit

Living room

iPod Tuner

PARTY mode

Main unit and iPod

Bedroom

Sub unit

Study room

Sub unit

Living room

iPod iPod

AIR-SA20PK.GB.4-117-793-11(1)

5GB

O perations

Press.S-AIR.MODE.on.the.remote. repeatedly.until.the.desired.S-AIR. mode.indicator.lights.up.in.the. display. The default setting is underlined.

MULTI SOURCE: Select this setting to listen to different sound sources on each sub unit.

PARTY: Select this setting to listen to the same sound source on multiple sub units.

To select the S-AIR mode from the system menu

1 Press.SYSTEM.MENU.on.the.unit.

2 Press.TUNING/SELECT.+/.on.the. unit.repeatedly.until.MODE.appears,. then.press.ENTER.on.the.unit.

3 Press.TUNING/SELECT.+/.on.the. unit.repeatedly.to.select.MULTI.or. PARTY,.then.press.ENTER.on.the. unit. The selected S-AIR mode appears on the display.

To check the S-AIR mode when the display of the main unit is turned off Press DISPLAY on the remote.

Notes When you change the S-AIR mode, the iPod

channel is automatically selected for the connected sub units.

When connecting the main unit to an S-AIR sub unit (such as the AIR-SA10) which is not compatible with the MULTI SOURCE mode, set the main unit to the PARTY mode. You can then select the S-AIR channel from the S-AIR sub unit.

Listening to iPod music using the S-AIR connection Use the sub units to listen to the music of an iPod connected to the main unit. You can control the connected iPod from either the main unit or the sub units.

To use an iPod, refer to the users guide of your iPod.

Using the main unit

1 Place.an.iPod.on.the.iPod. connector.as.shown.below.

Now, you are ready to listen to the connected iPod using the sub units.

2 Select.the.iPod.channel.

When the S-AIR mode is set to PARTY: Press PARTY CH on the remote repeatedly until iPod appears in the display.

When the S-AIR mode is set to MULTI SOURCE: The iPod channel is internally activated. Go to step 3.

Continued

AIR-SA20PK.GB.4-117-793-11(1)

GB

3 Start.playback. Operate the iPod to start playing the music. You can also operate the iPod using the remote (see To control the iPod using the main unit).

Using the sub units

1 Place.an.iPod.on.the.iPod. connector.on.the.main.unit.

2 Select.the.iPod.channel. Press S-AIR CH repeatedly until iPod appears in the display.

3 Start.playback. Operate the iPod to start playing the music. You can also operate the iPod using the remote (see To control the iPod using the sub units).

To control the iPod using the main unit You can control your iPod with the following buttons on the remote.

To Press Start playback

.

Pause playback

. To resume playback, press again.

Select a menu or track for playback

/. You can scroll up or down the iPod menus.

Skip a track /. Find a point in a track

Hold down / during playback, and release the button at the desired point.

To Press Choose the selected item

ENTER. You can choose the selected item much like the center button on the iPod.

Return to the previous menu

MENU. You can return to the previous menu much like the Menu button on the iPod.

To control the iPod using the sub units You can control your iPod with the following buttons on the remote or unit.

To Press Start playback

.

Pause playback

, or /CANCEL. To resume playback, press or .

Skip a track /. Find a point in a track

Hold down / during playback, and release the button at the desired point.

Adjust the volume

VOLUME +/.

AIR-SA20PK.GB.4-117-793-11(1)

GB

O perations

To use the main unit as a battery charger You can use the main unit as a battery charger for the iPod when the main unit is on. The charging begins when the iPod is placed on the iPod connector. The charging status appears in the iPod display. For details, refer to the users guide of your iPod. To stop charging the iPod, remove the iPod or turn off the main unit.

Notes When placing or removing the iPod, handle

the iPod in the same angle as that of the iPod connector on the main unit and do not twist or sway the iPod to prevent connector damage.

Do not carry the main unit with an iPod set on the connector. Doing so may cause a malfunction.

When placing or removing the iPod, brace the main unit with one hand and take care not to press the controls of the iPod by mistake.

Before disconnecting the iPod, pause playback.

You cannot adjust the volume using the main unit.

The volume level does not change even if adjusted on the iPod.

The main unit is designed for iPod only. You cannot connect any other portable audio players.

Depending on the iPod model you are using and its status, operations using the main unit and the sub units may not be accepted or the wrong operations may be performed.

Sony cannot accept responsibility in the event that data recorded to iPod is lost or damaged when using an iPod with this S-AIR product.

Listening to the radio using the S-AIR connection

Using the main unit

1 Select.the.tuner.channel.

When the S-AIR mode is set to PARTY: Press PARTY CH on the remote repeatedly until FM or AM appears in the display.

When the S-AIR mode is set to MULTI SOURCE: The tuner channel is internally activated. Go to step 2.

2 Select.FM.or.AM. Press BAND repeatedly.

3 Perform.automatic.tuning. Press and hold TUNING +/ on the remote (or TUNING/SELECT +/ on the unit) until the frequency indication changes and then release. AUTO lights up in the display. Scanning stops automatically when a station is tuned in, and then TUNED and ST (for FM stereo programs only) appear.

Continued

AIR-SA20PK.GB.4-117-793-11(1)

GB

Using the sub units When a radio station is tuned on the main unit, you can listen to that station by following the steps below. To tune in a radio station using the sub units, that station needs to be preset beforehand (see To call up a preset radio station using the sub units (page 29)).

1 Select.the.tuner.channel. Press S-AIR CH repeatedly until TUNER appears in the display.

2 Select.FM.or.AM. Press and hold S-AIR CH until FM changes to AM or vice versa.

To tune in a station with a weak signal using the main unit If TUNED does not appear and the scanning does not stop, press TUNING +/ on the remote (or TUNING/ SELECT +/ on the unit) repeatedly to tune in the desired station.

To reduce static noise on a weak FM stereo station using the main unit

1 Press.SYSTEM.MENU.on.the.unit.

2 Press.TUNING/SELECT.+/.on.the. unit.repeatedly.until.FM.MODE. appears,.then.press.ENTER.on.the. unit.

3 Press.TUNING/SELECT.+/.on. the.unit.repeatedly.until.MONO. appears,.then.press.ENTER.on.the. unit. There will be no stereo effect, but the reception will improve.

Presetting radio stations You can preset your favorite radio stations and tune them in instantly by selecting the corresponding preset number. Use the main unit to preset the radio stations.

1 Tune.in.the.desired.station. See Listening to the radio using the S-AIR connection (page 27).

2 Press.SYSTEM.MENU.on.the.unit.

3 Press.TUNING/SELECT.+/. on.the.unit.repeatedly.until. MEMORY.appears,.then.press. ENTER.on.the.unit.

Preset number

4 Press.TUNING/SELECT.+/.on. the.unit.repeatedly.to.select. your.desired.preset.number. If another station is already assigned to the selected preset number, the station is replaced by the new stations.

AIR-SA20PK.GB.4-117-793-11(1)

GB

O perations

5 Press.ENTER.on.the.unit.

6 Repeat.steps.1.through.5.to. store.other.stations. You can preset up to 20 FM and 10 AM stations. The preset stations are retained for about half a day even if you disconnect the power supply cord or if a power failure occurs.

To call up a preset radio station using the main unit Press PRESET +/ repeatedly.

To call up a preset radio station using the sub units

1 Preset.radio.stations.on.the.main.unit. (see.Presetting.radio.stations.(page. 28)).

2 Select.the.tuner.channel. Press S-AIR CH repeatedly until TUNER appears in the display.

3 Select.FM.or.AM. Press and hold S-AIR CH until FM changes to AM or vice versa.

4 Press.PRESET.+/.repeatedly.to. select.a.preset.station.

Using an optional AV system You can enjoy audio and video of the connected iPod with an optional AV system.

1 Connect.an.optional.AV.system. (such.as.a.TV,.etc.).to.the.iPod. AUDIO.OUT.L/R.jacks.and/or. the.iPod.VIDEO.OUT.jack.of.the. main.unit.using.an.optional. audio.cord.and/or.video.cable.

2 Place.an.iPod.on.the.iPod. connector.on.the.main.unit.

3 Start.playback.of.the.iPod. See Listening to iPod music using the S-AIR connection (page 25).

Note The tuners sound cannot be output through

the iPod AUDIO OUT L/R jacks. Before enjoying video, adjust the video

settings on the iPod to the appropriate settings according to your situation.

Tip Even if you change the S-AIR mode or the S-AIR channel using PARTY CH, audio and/or video from the connected iPod will continue to be output from the iPod AUDIO L/R jacks and/or the iPod VIDEO OUT jack.

AIR-SA20PK.GB.4-117-793-11(1)

0GB

Changing the display

Using the main unit

To view the information on the display Press DISPLAY on the remote.

Using the sub units

To change the information on the display while the sub unit is on Press DISPLAY on the unit. Each time you press the button, the display changes as follows:

When the sub unit is connected to the main unit: Information of the connected main unit1) Model name of the connected main unit2) Clock2) ...

When the sub unit is not connected to the main unit: S-AIR UNLINKED2) Clock2) ...

1) Depending on the iPod model you are using, up to 16 characters of the following information can be viewed, for example, while playing the iPod. Track name Artist name Album name Elapsed playing time of the track

Characters that cannot be displayed appear as _.

When listening to the radio, the frequency is displayed.

2) Displayed for about 8 seconds.

To turn off the display of the sub unit When the sub unit is turned off, the clock is displayed. You can turn off the clock display to minimize the amount of power consumed (Power Saving Mode). Press DISPLAY on the unit when the clock is displayed. Press the button again to display the clock.

Note Regardless of the selected S-AIR mode, when the same S-AIR channel is selected on multiple sub units and you change the display of any one of them, the display on all sub units will change (only when the information of the connected main unit is displayed).

AIR-SA20PK.GB.4-117-793-11(1)

1GB

O perations

Using the Timers The sub units offer two timer functions. If you use the Daily Timer with the Sleep Timer, the Sleep Timer has priority. Use buttons on the unit to set the timers.

Sleep Timer: You can fall asleep to music. This function works even if the clock is not set. Press SLEEP repeatedly.

Note Even if you set the timer, no sound is output from the sub units if playback on the connected main unit ends within the set time period or if communication with the main unit is cut off.

Daily Timer: You can wake up to the sound of the connected main unit at a preset time. Make sure you have set the clock.

1 Press.VOLUME.+/.repeatedly. to.adjust.the.volume.level. while.viewing.the.volume.level. indication.on.the.display.

2 Press.CLOCK/TIMER.MENU.

3 Press./.repeatedly. to.select.TIMER,.then.press. CLOCK/TIMER.ENTER. ON TIME appears, and the hour indication flashes.

4 Set.the.time.to.start.playing. Press / repeatedly to set the hour, and then press CLOCK/TIMER ENTER. The minute indication flashes. Use the procedure above to set the minute.

5 Use.the.same.procedure.as.in. step.4.to.set.the.time.to.stop. playing.

6 Press./.repeatedly.to. select.the.desired.option. The default setting is underlined.

ALARM: An alarm is output.

AUTO: Sound from the connected main unit is output. However, an alarm sounds in the following cases. When communication with the

main unit is cut off. When no sound is output from the

main unit or the audio signal level is too low.

When the main unit is not ready for playback at the set start time. Note that the alarm continues to sound even if the main unit becomes ready after the start time has passed.

7 Press.CLOCK/TIMER.ENTER. The display shows the timer settings.

Continued

AIR-SA20PK.GB.4-117-793-11(1)

GB

8 If.you.selected.ALARM.in.step. 6,.go.to.step.9.. If.you.selected.AUTO.in.step. 6,.prepare.the.sound.source.on. the.main.unit.

iPod: Select the track to be played back by the timer, and set the iPod to the pause mode.

Tuner: Tune in the desired station (see Listening to the radio using the S-AIR connection (page 27) and Presetting radio stations (page 28)).

9 Press..to.turn.off.the.unit. The sub unit turns on about 45 seconds before the preset time. If the sub unit is on at the preset time, the Daily Timer will not play.

To stop the alarm Press any button.

To activate or check the timer again

1 Press.CLOCK/TIMER.MENU. SELECT flashes in the display.

2 Press.CLOCK/TIMER.ENTER.

3 Press./.repeatedly.to.select. TIMER.

4 Press.CLOCK/TIMER.ENTER.

To cancel the timer

1 Press.CLOCK/TIMER.MENU. SELECT flashes in the display.

2 Press.CLOCK/TIMER.ENTER.

3 Press./.repeatedly.to.select. OFF.

4 Press.CLOCK/TIMER.ENTER.

To change the setting Start over from step 1.

Note Even when AUTO is selected in step 6 and the iPod is to be played using the timer, timer playback may not start and the iPod may be set to the pause mode if the iPod was being played by another sub unit when the timer started operating. In this case, press on the sub unit.

Tip The Daily Timer setting remains as long as the setting is not canceled manually.

AIR-SA20PK.GB.4-117-793-11(1)

GB

O perations

Turning off the remote control function of the sub units When using the multiple sub units near each other, all the sub units may receive the same signal from the remote and the main unit may not function properly. To prevent this, you can turn off the remote control function of the sub units. Use buttons on the sub unit whose remote control function you want to turn off.

1 Press..to.turn.off.the.unit.

2 Press.DISPLAY.repeatedly.until. the.clock.is.displayed.

3 Press..while.holding.down. CLOCK/TIMER.ENTER. RMT OFF appears in the display and the sub unit is turned on. If you try controlling the sub unit using the remote, RMT OFF appears in the display and the sub unit will not accept the signal from the remote.

To turn on the remote control function Perform steps 1 and 3 above and check that RMT ON appears in the display.

Note Even when the remote control function is turned off, and VOLUME +/ on the remote will continue to function.

Changing the illumination brightness of the main unit Press.ILLUMINATION.repeatedly. Each time you press the button, the illumination brightness changes as follows:

Bright Darkened Off

AIR-SA20PK.GB.4-117-793-11(1)

GB

Others

Troubleshooting 1 Make.sure.the.power.supply.

cord.and.the.power.cord.are. correctly.and.firmly.connected.

2 Find.your.problem.in.the. checklist.below,.and.take.the. indicated.corrective.action.

If the issue persists, contact your nearest Sony dealer. When bringing the product in for repairs, be sure to bring in the entire system (the main unit, the sub units and wireless transceivers). This product is a system product, and the entire system is needed to determine the location requiring repair.

If PROTECT appears on the display of the main unit Set the POWER switch on the rear panel to OFF to turn off the unit, and then unplug the power supply cord. After checking that there is no indication on the display, reconnect the power supply cord and set the POWER switch to ON to turn on the unit. If the issue persists, contact your nearest Sony dealer.

If the STANDBY indicator on the sub unit flashes Immediately unplug the power cord, and check if anything is blocking the ventilation holes on the rear panel of the unit. After the STANDBY indicator stops flashing, reconnect the power cord, and turn on the unit. If the issue persists, contact your nearest Sony dealer.

General

The remote does not function. Remove any obstacles between the

remote and the remote sensor, and position the main unit and the sub units away from fluorescent lights.

Point the remote at the remote sensor. Move the remote closer to the main

unit or the sub units. The remote control function of the sub

unit is off. Turn on the remote control function (page 33).

Check whether you are using the remote for the main unit to operate the main unit and the remote for the sub unit to operate the sub unit.

The S-AIR indicators on the main unit and the sub units are turned off. Check that the power supply cord and

the power cord are connected securely and the main unit and the sub units are turned on.

Check that the supplied wireless transceivers are inserted securely to the main unit and the sub units (page 19).

Connecting the main unit and the sub units is not possible. (The S-AIR indicator on the main unit is turned off and/or the S-AIR indicator on the sub unit flashes.) Check that the supplied wireless

transceivers are inserted securely to the main unit and the sub units (page 19).

If you use another S-AIR main unit, place it more than 8 m away from the main unit.

Confirm the S-AIR IDs of the main unit and the sub units.

The main unit is paired with another S-AIR sub unit. Pair the main unit with the sub unit you are using.

AIR-SA20PK.GB.4-117-793-11(1)

5GB

O thers

The main unit is paired with another S-AIR sub unit. Cancel pairing.

Place so that the main unit and the sub units are separated from other wireless devices.

Stop using any other wireless devices. The main unit or the sub unit is turned

off. Make sure the power supply cord and the power cord are connected and turn on the main unit and the sub units.

The S-AIR channel fails to change. Check that the main unit and the sub

units are connected properly. If you are using an optional S-AIR sub

unit (such as the AIR-SA10) which is not compatible with the MULTI SOURCE mode, set the main unit to the PARTY mode.

There is no sound. If you use another S-AIR main unit,

place it more than 8 m away from the main unit.

Confirm the S-AIR IDs of the main unit and the sub units.

Check the pairing setting. Place so that the main unit and the sub

units are closer. Stop using any equipment that

generates electromagnetic energy such as a microwave oven.

Place so that the main unit and the sub units are separated from other wireless devices.

Stop using any other wireless devices. Change the S-AIR ID settings of the

main unit and the sub units. Turn off the main unit and the sub

units and then turn them on again.

Check that the power supply cord and the power cord are connected securely and the main unit and the sub units are turned on.

Increase the volume of the sub units. Check that headphones are not

connected to the (headphones) jack on the rear panel of the sub units.

Change the RF CHANGE setting on the main unit (page 22).

There is noise or the sound skips. If you use another S-AIR main unit,

place it more than 8 m away from the main unit.

Place so that the main unit and the sub units are closer.

Stop using any equipment that generates electromagnetic energy such as a microwave oven.

Place so that the main unit and the sub units are separated from other wireless devices.

Stop using any other wireless devices. Change the S-AIR ID settings of the

main unit and the sub units. Do not place a mobile phone near the

main unit and the sub units, as this may result in noise.

Change the RF CHANGE setting on the main unit (page 22).

Continued

AIR-SA20PK.GB.4-117-793-11(1)

GB

iPod

There is no sound. Make sure the iPod is connected

securely. Make sure the iPod is playing music. Adjust the volume of the sub units. Update your iPod to use the latest

software.

The iPod cannot be operated by the main unit or the sub units. Check that the iPod and the main

unit are connected properly and that the main unit and the sub units are connected properly.

Depending on the iPod model you are using and its status, it may not be possible to operate the iPod using the main unit or the sub units.

Update your iPod to use the latest software.

The sound is distorted. Turn down the volume of the sub units. Set the EQ setting of the iPod to

Off or Flat.

The iPod cannot be charged. Make sure the iPod is connected

securely. Check that the power supply cord is

connected securely and the main unit is turned on.

The iPod track information cannot be obtained. Depending on the iPod model

you are using and its status, it may not be possible to obtain the track information properly during playback.

Up to 16 characters can be displayed on the displays of the sub units.

Check that the track information has been entered into the iPod.

Video/Photo image from the connected iPod does not appear on the TV screen. Make the connection according to your

AV system. Switch the TV input to the video input

connected to the main unit. Check that the TV output setting on

the iPod is on (Refer to the users guide of your iPod).

Check that the iPod is compatible with video output (Refer to the users guide of your iPod).

Tuner

Severe hum or noise, or stations cannot be received. (TUNED or ST flashes on the display of the main unit.) Connect the antennas properly. Find a location and an orientation that

provide good reception, and then set up the antennas again.

Keep the antennas away from the power supply cord to avoid picking up noise.

Connect a commercially available external antenna.

Consult your nearest Sony dealer if the supplied AM antenna has come off the plastic stand.

Turn off nearby electrical equipment.

AIR-SA20PK.GB.4-117-793-11(1)

GB

O thers

To change the AM tuning interval The AM tuning interval is factory-preset to 10 kHz. Use the main unit to change the AM tuning interval.

1 Tune.in.any.AM.station.

2 Press.SYSTEM.MENU.on.the.unit.

3 Press.TUNING/SELECT.+/.on.the. unit.repeatedly.until.AM.STEP. appears,.then.press.ENTER.on.the. unit.

4 Press.TUNING/SELECT.+/.on.the. unit.repeatedly.to.select.9K.or.10K,. then.press.ENTER.on.the.unit. OK appears.

5 Press.ENTER.on.the.unit.again.to. confirm.the.setting. When you change the interval, all the AM preset stations are erased. To reset the interval to the factory preset, repeat the procedure.

To reset the main unit to factory settings If the main unit still does not operate properly, reset the main unit to factory settings.

1 Disconnect.and.reconnect.the.power. supply.cord,.and.then.turn.on.the. unit.

2 Press.SYSTEM.MENU.on.the.unit.

3 Press.TUNING/SELECT.+/.on.the. unit.repeatedly.until.RESET.appears,. then.press.ENTER.on.the.unit. RESET OK appears.

4 Press.ENTER.on.the.unit.again.to. confirm.the.setting. All user-configured settings are deleted, such as preset radio stations.

To reset the sub unit to factory settings If the sub unit still does not operate properly, reset the sub unit to factory settings.

1 Disconnect.and.reconnect.the.power. cord,.and.then.turn.on.the.unit.

2 Press./CANCEL,.DISPLAY.and.. on.the.unit.at.the.same.time. All user-configured settings, such as timer, clock, etc. are deleted.

AIR-SA20PK.GB.4-117-793-11(1)

GB

Messages CANCEL : Time out without pairing. COMPLETE : Pairing is completed. ID A : Sets the S-AIR ID to A. ID B : Sets the S-AIR ID to B. ID C : Sets the S-AIR ID to C. LINKED* : The sub unit is connected to

the main unit. PAIRING : Pairing is in progress. RMT OFF* : The sub units are not

accepting signals from the remote because the remote control function is set to RMT OFF.

S-AIR* : Displayed from the point power of the sub unit is turned on until connection with the main unit is established.

TIME NG* : The Daily Timer start and end times are set to the same time.

UNLINKED* : The connection with the main unit is cut off.

* Displayed on the sub units only.

Precautions Notes on use of the S-AIR product As the S-AIR product transmits sound

by radio waves, sound may skip when radio waves are obstructed. This is a characteristic of radio waves and is not a malfunction.

As the S-AIR product transmits sound by radio waves, equipment that generates electromagnetic energy, such as a microwave oven, may interfere with sound transmission.

As the S-AIR product uses the radio waves that share the same frequency as other wireless systems, such as wireless LAN or Bluetooth devices, interference or poor transmission may result. In this case, take the following steps: Do not install the S-AIR product

near other wireless systems. Do not use the S-AIR product and

the other wireless systems at the same time.

The transmission distance differs depending on the usage environment. Find a location where transmission between the main unit and the sub units is most effective, and install the main unit and the sub units there.

AIR-SA20PK.GB.4-117-793-11(1)

GB

O thers

On safety Completely disconnect the power

supply cord and the power cord from the wall socket (mains) if the main unit and the sub units are not going to be used for an extended period of time. When unplugging the units, always grip the plug. Never pull the cord itself.

Should any solid object or liquid get into the main unit and the sub units, unplug the units, and have them checked by qualified personnel before operating them again.

The power supply cord and the power cord can be changed only by a qualified service facility.

On placement Do not place the main unit and the

sub units in an inclined position or in locations that are extremely hot, cold, dusty, dirty, or humid or lacking adequate ventilation, or subject to vibration, direct sunlight or a bright light.

Be careful when placing the main unit and the sub units on surfaces that have been specially treated (for example, with wax, oil, polish) as staining or discoloration of the surface may result.

On heat buildup Heat buildup on the main unit and the

sub units during operation is normal and is not cause for alarm.

Do not touch the cabinet if it has been used continuously at a high volume because the cabinet may have become hot.*

Do not obstruct the ventilation holes.*

* The sub units only.

On the speaker system* This speaker system is not magnetically shielded, and the picture on nearby TV sets may become magnetically distorted. In this situation, turn off the TV, wait about 15 to 30 minutes, and turn it back on. If there is no improvement, move the unit far away from the TV.

* The sub units only.

Cleaning the cabinet Clean the cabinet with a soft dry cloth. Do not use any type of abrasive pad, scouring powder, or solvent, such as thinner, benzine, or alcohol.

AIR-SA20PK.GB.4-117-793-12(1)

40GB

Specifications Main unit (AIR-SA15Ti)

Output AUDIO OUT:

voltage 775 mV, impedance 47 kilohms

VIDEO OUT: Max. output level 1 Vp-p, unbalanced, Sync. negative, load impedance 75 ohms (Composite Video Out)

Wireless transceiver (EZW-RT10/EZW- RT10A) Communication System:

S-AIR Specification version 1.0 Frequency band:

2.4000 GHz 2.4835 GHz Modulation method:

DSSS Power requirements:

DC 3.3 V, 350 mA Dimensions (w/h/d):

50 13 60 mm Mass:

24 g

Tuner section FM stereo, FM/AM superheterodyne tuner FM tuner section: Tuning range:

87.5 108.0 MHz (100 kHz step) Antenna:

FM lead antenna Antenna terminals:

75 ohms unbalanced Intermediate frequency:

10.7 MHz AM tuner section: Tuning range:

530 1,710 kHz (with 10 kHz tuning interval) 531 1,710 kHz (with 9 kHz tuning interval)

Antenna: AM loop antenna, external antenna terminal

Intermediate frequency: 450 kHz

General Power requirements:

120 V AC, 60 Hz Power consumption:

15 watts Dimensions (w/h/d) (excluding the AC power supply unit):

Approx. 295 43 110 mm Mass (including the AC power supply unit):

Approx. 1.1 kg

AIR-SA20PK.GB.4-117-793-12(1)

41GB

O thers

Sub unit (AIR-SA15R)

Amplifier section U.S.A. model: AUDIO POWER SPECIFICATIONS POWER OUTPUT AND TOTAL HARMONIC DISTORTION: With 3 ohms loads, both channels driven, from 300 20,000Hz; rated 4 watts per channel minimum RMS power, with no more than 10% total harmonic distortion from 250 milliwatts to rated output.

Other models: Continuous RMS power output (reference):

4 + 4 watts (3 ohms at 1 kHz, 10% THD)

Output (stereo mini jack):

Accepts headphones with an impedance of 8 ohms or more

Speaker section Speaker system:

Full range, bass-reflex type Speaker units:

65 mm, cone type (2) Nominal impedance:

3 ohms

Wireless transceiver (EZW-RT10/EZW- RT10A) Communication System:

S-AIR Specification version 1.0 Frequency band:

2.4000 GHz 2.4835 GHz Modulation method:

DSSS Power requirements:

DC 3.3 V, 350 mA Dimensions (w/h/d):

50 13 60 mm Mass:

24 g

General Power requirements:

120 V AC, 60 Hz Power consumption:

15 watts Dimensions (w/h/d):

Approx. 300 136 115 mm Mass:

Approx. 2.2 kg

Design and specifications are subject to change without notice.

Halogenated flame retardants are not used in the certain printed wiring boards.

AIR-SA20PK.GB.4-117-793-11(1)

GB

Compatible iPod models You can use the following iPod models on the main unit. Update your iPod with the latest software before using it.

iPod touch iPod nano 3rd generation (video)

iPod classic iPod nano 2nd generation

(aluminum)

iPod 5th generation (video)

iPod nano 1st generation

iPod 4th generation (color display)

iPod 4th generation

iPod mini

AIR-SA20PK.GB.4-117-793-11(1)

O thers

GB

Index A Alarm 31 AM tuning interval 37 Antennas 19 Automatic tuning 27

B Batteries 20

C Clock 23 Compatible iPod 42

I Illumination 33 Installation 8 iPod

Charging 27 Controlling 26 Listening 25

iPod AUDIO OUT L/R 29 iPod Dock Adapters 19 iPod VIDEO OUT 29

M Main unit 10 MULTI SOURCE mode 24

O Other component hookup 29

P Pairing 21 PARTY mode 24 Power Saving Mode 30 Presetting radio stations 28

R Radio 27 Remote 11, 15, 33 Reset 37 RF CHANGE 22

S S-AIR 8 S-AIR connection 20 S-AIR ID 19, 20 S-AIR mode 24 Sub unit 14

T Timer

Daily Timer 31 Sleep Timer 31

Troubleshooting 34

W Wireless transceiver 19

Manualsnet FAQs

If you want to find out how the AIR SA20PK Sony works, you can view and download the Sony AIR SA20PK Operating Instruction on the Manualsnet website.

Yes, we have the Operating Instruction for Sony AIR SA20PK as well as other Sony manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Operating Instruction should include all the details that are needed to use a Sony AIR SA20PK. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Sony AIR SA20PK Operating Instruction is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Sony AIR SA20PK Operating Instruction consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Sony AIR SA20PK Operating Instruction free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Sony AIR SA20PK Operating Instruction, simply download the document to your computer. Once downloaded, open the PDF file and print the Sony AIR SA20PK Operating Instruction as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.