SMC EX9-ZSW-IPC1 Tool Operation Manual PDF

No.EX-OMV1026-B

PRODUCT NAME

IP Address Setting Tool

(Interactive Type)

MODEL / Series / Product Number

EX9ZSWIPC1

-1-

No.EX-OMV1026-B

Table of Contents

1. License Agreement 2

2. Product Outline 3

3. Network Configuration Example 4

4. Setting the EtherNet/IPTM Device 5

5. Setting the Computers IP Address 6

6. IP address setting of the IP Address Setting Tool 8

7. Option Setting 11

8. Log monitor function 11

9. Export Function 12

10. Troubleshooting 13

11. Definitions and Terminology (Supplementary Explanation) 15

-2-

No.EX-OMV1026-B

1. License Agreement

SMC Corporation (hereinafter referred to as "SMC") hereby grants the user (regardless of whether the user is a corporation or an individual) a license to use this software "IP Address Setting Tool" (hereinafter referred to as "Software") according to this License agreement (hereinafter referred to as "Agreement") under the articles listed below.

Please check the content of this License Agreement, and only use it if you agree to all the terms and conditions herein. You cannot use this software, unless you agree with all the terms and conditions of this Licence Agreement.

Article 1 (Grant of license) 1. This Software is intended for use with the respective SMC EtherNet/IP Target product

(henceforth referred to as Target product) and it can only be used with Target products, in accordance with this licence agreement.

2. This software can only be installed on a PC for the sole purpose specified in the preceding paragraph.

Article 2 (Restrictions) 1. This software is not to be copied, except as specified in Article 1-2. 2. This software license is not to be transferred or loaned wholly or in part to a third party, either free

of charge or for payment. 3. Modification, translation, adaptation or reverse engineering of this software is not permitted. 4. The user cannot use this software other than with the Target product. 5. This software cannot be used other than with the firmware which SMC provides.

Article 3 (Other notices) 1. Read the "Safety Instructions", "Precautions", "Specific Product Precautions" and "Specifications"

described in the manual for the equipment when using any Target product supported by this Software.

2. This Software and the Target product are subject to change without prior notice.

Article 4 (Exemption of liability) SMC cannot take any responsibility for any loss or damage incurred by the use of this Software or for any loss or damage that may occur as a consequence of the use of this software.

Article 5 (Termination) 1. SMC has the full authority to terminate this agreement without notice and without any

compensation in the event that any terms and conditions have been breached. 2. This Software and any copies thereof must be destroyed when this Agreement is terminated.

Article 6 (Rights of this Software) The copyright and any other rights of this Software are owned by SMC, and protected by Japanese copyright laws and international treaty provisions.

Article 7 (Governing law and jurisdiction) 1. This Agreement shall be governed by Japanese law. 2. Any dispute arising from this Agreement shall be submitted in the first instance to the exclusive

jurisdiction of the Tokyo District Court or the Tokyo Summary Court primarily.

-3-

No.EX-OMV1026-B

2. Product Outline

To connect an EtherNet/IP product to the EtherNet/IP network (hereafter referred to as "the network), it is necessary to set the IP address. The IP Address Setting Tool is a tool for setting the IP address during DHCP mode and Remote control mode.

Operating systems for IP Address Setting Tool are as follows. WindowsXP (32/64bit) Windows7 (32/64bit) Windows8 (32/64bit) Windows10 (32/64bit)

1) Install Microsoft .NET Framework 4 or later before use.

2) This tool might not operate correctly depending on the security setting of the PC. In that case, disable the security setting temporarily and try to use it again.

Applicable products are as follows.

EX260-SEN1/2/3/4 EX500-GEN2 EX600-SEN1/2/3/4 EX600-WEN1/2 JXC91/JXC92/JXC93

: When the DHCP mode and the remote control mode are set

Make sure that all downloaded files are in the same folder as the EX9-ZSW-IPC1.exe file before use. DhcpServerDll.dll

PacketDotNet.dll 3)

SharpPcap.dll (3) Etc.

3) This is the open source software. For details, please refer to "open_source_License" which is located in the folder in which all of the downloaded files are saved.

-4-

No.EX-OMV1026-B

3. Network Configuration Example

Set the IP address while disconnected from the EtherNet/IPTM module (master). It is not possible to maintain the IP address while communicating with the EtherNet/IPTM module (based

unit).

IP address setting (example):

Device IP address Subnet mask

PC 192.168.0.253

255.255.255.0 EX260-SEN1 192.168.0.10

EX600-SEN3 192.168.0.11

Fig. Network Configuration Example

LAN cable

EX600-SEN3

PC (Commercially available

product) Switching hub

(Unmanaged switch)

-5-

No.EX-OMV1026-B

4. Setting the EtherNet/IPTM Device

No. Display Instructions

(1) < Rotary switch (EX260-SEN#, etc.) >

: Example above: EX260-SEN#

< DIP switch (EX600-SEN#, etc.) >

IP address setting switches

Settings2 IP address

1 2 3 4 5 6 7 8

ON OFF OFF OFF OFF OFF OFF OFF 192.168.0.1

OFF ON OFF OFF OFF OFF OFF OFF 192.168.0.2

: : : : : : : : :

ON OFF ON ON ON ON ON ON 192.168.0.253

OFF ON ON ON ON ON ON ON 192.168.0.254

ON OFF OFF OFF OFF OFF OFF OFF 192.168.1.1

OFF ON OFF OFF OFF OFF OFF OFF 192.168.1.2

: : : : : : : : :

ON OFF ON ON ON ON ON ON 192.168.1.253

OFF ON ON ON ON ON ON ON 192.168.1.254

ON ON ON ON ON ON ON ON DHCP mode

OFF OFF OFF OFF OFF OFF OFF OFF Remote Control mode

: Example above: EX600-SEN#

< others (EX600-WEN#, etc.) >

Refer to each operation manual.

Set the EtherNet/IPTM device to Remote

control mode. Rotary switch: Set the IP

address setting switches to 000.

DIP switch: Set all switches to OFF.

Refer to the operation manual of each

EtherNet/IPTM device for further details.

: When the NS LED on the

EtherNet/IPTM device is ON or

flashes, turn on the power with the IP

address switch setting set to "255" or

all ON (DHCP mode) and initialize the

IP address stored in the EtherNet/IPTM

device. Then change the IP address

switch setting to 000 or turn them all

off (Remote control mode) and reset.

: Initialize the IP address with the

software closed.

-6-

No.EX-OMV1026-B

5. Setting the Computers IP Address

Set the IP address for the Setting the Computers IP Address following the procedure (2) to (7) below.

The setting procedure is based on Windows10.

No. Display Instructions

(2)

Click Control Panel and Network and

Internet.

(3)

Click Network and Sharing Centre and

View networks status and tasks.

(4)

Click View your active networks and

Connections: Ethernet.

: This field is blank when the device is

not connected.

-7-

No.EX-OMV1026-B

(5)

Click "Properties.

(6)

Select the Internet Protocol Version 4

(TCP/IPv4) and click "Properties.

(7)

[When a DHCP server is not installed

on the network]

To specify the IP address directly

without a DHCP server, select "Use the

following IP address" on the "Internet

Protocol Version 4 (TCP/IPv4)

Properties" screen, enter values in "IP

address" and "Subnet mask," and then

click OK.

Values that are entered in "IP address"

and "Subnet mask" must be set

according to the network used.

: As an example in the left figure,

IP address =192.168.0.253

Subnet mask =255.255.255.0

are entered.

In this case, the network address is

"192.168.0".

-8-

No.EX-OMV1026-B

6. IP address setting of the IP Address Setting Tool

Set the IP address for the IP Address Setting Tool following the procedure (8) to (18) below.

No. Display Instructions

(8)

When the computer IP address has

been set and the IP Address Setting

Tool starts, the License agreement

screen will appear.

If the terms of the agreement are

acceptable, select I accept the terms in

the license agreement and click OK.

(9)

The Network Setting screen starts.

Select the network interface. If the

screen does not need to appear the next

time, tick the box for Do not show this

dialog box at startup

After selecting, click the [OK] button.

(10)

On the first boot, Windows Security

Alert concerning a Firewall may be

displayed. In this case, click Allow

access.

: Make sure that the box for the

"Private networks or Public networks

is checked.

(11)

When the main screen appears, click

Scan to check the connected unit.

(12)

If the IP address is not set yet, only the

MAC address will appear.

: When setting the IP address manually

or it is not a compatible product, the

MAC address will be grayed out.

-9-

No.EX-OMV1026-B

(13)

Select the item icon that shows the

same MAC address number on the IP

address setting tool as the MAC

address on a label attached to the

housing of the unit for which the IP

address is to be set.

(14)

When the setting screen appears, set

the IP address, Subnet mask, and other

items.

After setting, click the [OK] button.

When the IP address is not to be

retained in Remote control mode, tick

the box for No storage Mode.

(15)

When setting is completed, the set

values such as the IP address will

appear.

Also, "Parameters setting success" will

appear in the bottom left.

: It is not possible to maintain the IP

address (Storage Mode, Disable DHCP)

while communicating with the

EtherNet/IPTM module (master).

Set the IP address while disconnected

from the EtherNet/IPTM module (master).

-10-

No.EX-OMV1026-B

Caution)

When Cancel is clicked for the Windows Security Alert in step No. (10), the access permission needs to be set

following the procedure below.

(16)

Select Control panel and System and

Security.

(17)

Select Allow an app through Windows

Firewall.

(18)

(1) Click Change settings and select

Allowed apps and features, then click

smc ip address setting tool.exe. (2)

Check the box for the smc ip address

setting tool.exe and click OK (3).

: Make sure that the box for the

"Private networks or Public networks

is checked.

-11-

No.EX-OMV1026-B

7. Option Setting

Set the optional function in accordance with steps 19 to 20 below.

(19)

Click Option to display the Option

Setting screen.

(20)

The Option Setting screen is

displayed.

Items that are checked will function.

Uncheck unnecessary items.

The setting can be reset by clicking the

Default button.

8. Log monitor function

It is possible to monitor the scanned status using this tool.

(21)

Display the option screen and check the

LogMonitor.

(22)

The Log Monitor window is displayed on

the main screen.

-12-

No.EX-OMV1026-B

(23)

When scanning or IP

address setting is

performed, the

processed information

is displayed as a log.

(24)

Enter a keyword to

Filter the log, and click

the Filter button. The line in which the entered keyword is shown is displayed.

(25)

To clear the Log

Monitor information,

click the Clear button.

The display will be

cleared.

9. Export Function

This tool stores the scanned device list as a csv file.

(26)

Click File > Export, and then save the

csv file in the folder of your choice.

The stored csv file can be used for the

IP Setting Tool (presetting type).

-13-

No.EX-OMV1026-B

10. Troubleshooting

Troubleshooting flow chart

Perform the following troubleshooting procedure when the IP address setting is not successful.

The MS LED on the EtherNet/IPTM device and the L/A (LINK ACT) LED should be green when the wiring for

the power supply and communication connector are normal. Refer to the operation manual of each

EtherNet/IPTM device for details.

Note: EX600-SEN1/2 does not have L/A (LINK ACT) installed.

Green ON, Green flashes, Red ON, or Red flashes.

LED check Refer to fault

No. 1

Refer to fault

No. 2

Refer to fault

No. 3

Scan is not

available

IP address is not

held

EtherNet/IPTM device NS

LED is ON or flashes ()

Yes No

EtherNet/IPTM device NS

LED is OFF

-14-

No.EX-OMV1026-B

Troubleshooting list

Fault No.1

Problem Possible cause Investigation method Countermeasures

EtherNet/IPTM device NS

LED is ON or flashes

(Green ON, Green

flashes, Red ON, or Red

flashes)

EtherNet/IPTM device IP

address is set

Check the EtherNet/IPTM

device IP address switch

setting.

Set the IP address switch setting

for the EtherNet/IPTM device to

000 or turn off all switches

(Remote control mode).

IP address stored in the

EtherNet/IPTM device is

initialized.

When the switch setting of the

EtherNet/IPTM device is 255 or

all switches are ON (DHCP

mode), turn on the power and

initialize the IP address stored in

the EtherNet/IPTM device. Then

change the IP address switch

setting to 000 or turn them all

off (Remote control mode) to

reset.

: Initialize the IP address with

the software closed.

Fault No.2

Problem Possible cause Investigation method Countermeasures

Scan is not available

(EtherNet/IPTM device NS

LED is OFF)

Security setting

Check the security setting

including the Windows

firewall.

Disable the security setting

temporarily or select Allow

remote access while referring to

procedure No. (16) to No. (18) in

page 10.

Fault No.3

Problem Possible cause Investigation method Countermeasures

IP address is not held

IP Address setting for

computer (PC)

Check the IP Address

and the Subnet mask

setting for the PC.

Set appropriate IP address of the

PC and Subnet mask for the

network.

Procedure No. (7) on page 7.

Network Configuration Check the EtherNet/IPTM

module connection.

Disconnect the communication

cable for the EtherNet/IPTM

module or turn off the device

power.

IP address switch setting

Check the EtherNet/IPTM

device IP address switch

setting.

Set the IP address switch setting

for the EtherNet/IPTM device to

000 or turn off all switches

(Remote control mode).

Setting of the IP Address Check the IP Address

Setting.

Uncheck the box for No Storage

Mode in the IP Address

Setting.

Procedure No. (14) on page 9.

-15-

No.EX-OMV1026-B

11. Definitions and Terminology (Supplementary Explanation)

Please refer to the table below for glossary.

Terminology Definition

D

DHCP A protocol that automatically allocates information, necessary to be registered to use the network, such as an IP address, to individual devices connected to the TCP/IP network.

DHCP mode Mode to obtain an IP address from the DHCP Server. The IP address will be lost when the power supply is disconnected. Refer to the operation manual for setting the product.

DHCP server

DHCP is an abbreviation of Dynamic Host Configuration Protocol. It is a server that automatically allocates information, necessary to be registered to use the network, such as an IP address, to individual devices on the network.

I IP address

A 32 bit digit sequence which is assigned to identify devices which are connected to the network.

M MAC address

A unique number assigned to all devices connected to an EtherNet/IPTM network.

R Remote control mode

An IP address obtained via the DHCP server can be held. Refer to the operation manual for the products for setting.

S Subnet mask

Numerical values that define the range of the numerical string within the IP address used on the network.

Switching hub Device that works as a relay in the network.

No.EX-OMV1026-B

Revision history

A: Contents are added. [August 2018]

B: Contents are added. [December 2020]

4-14-1, Sotokanda, Chiyoda-ku, Tokyo 101-0021 JAPAN Tel: + 81 3 5207 8249 Fax: +81 3 5298 5362 URL https://www.smcworld.com NOTE: Specifications are subject to change without prior notice and any obligation