Sennheiser SZI 1015 Instruction Manual PDF

1 of 27
1 of 27

Summary of Content for Sennheiser SZI 1015 Instruction Manual PDF

1

SI 1015 SZI 1015

BEDIENUNGSANLEITUNG INSTRUCTIONS FOR USE NOTICE DEMPLOI ISTRUZIONI PER LUSO INSTRUCCIONES PARA EL USO GEBRUIKSAANWIJZING

32

SI 1015 SZI 1015BEDIENUNGSANLEITUNG

BEDIENUNGSANLEITUNG .................................................................................................................................. 3 INSTRUCTIONS FOR USE .................................................................................................................................. 11 NOTICE DEMPLOI .............................................................................................................................................. 19 ISTRUZIONI PER LUSO ..................................................................................................................................... 27 INSTRUCCIONES PARA EL USO ....................................................................................................................... 35 GEBRUIKSAANWIJZING ................................................................................................................................... 43

5

4

Anschlu- und Bedienelemente SI 1015 (Frontseite) Ein- / Aus-Schalter

Netzkontroll-LED

bersteuerungsanzeige Kanal A

Pegelsteller Kanal A

bersteuerungsanzeige Kanal B

Pegelsteller Kanal B

Wahlschalter: Kanal A Kanal B Kanal A/B, 2 x mono Kanal A und B als Stereo-Signal

IR-Sendedioden (zur direkten Kontrolle durch einen IR-Empfnger)

Anschlu- und Bedienelemente SI 1015 (Rckseite) HF-Ausgangsbuchse 1, Anschlu fr Leistungsstrahler

HF-Klemmanschlu 1, Anschlu fr Leistungsstrahler (parallel zu )

Anschlu 1 Stromversorgung Leistungsstrahler (durchgeschleift von )

Anschlu 2 Stromversorgung Leistungsstrahler (durchgeschleift von )

HF-Klemmanschlu 2, Anschlu fr Leistungsstrahler (parallel zu )

HF-Ausgangsbuchse 2, Anschlu fr Leistungsstrahler (gleiches Signal wie )

NF-Eingang B

Zugentlastung

NF-Eingang A

Anschlu Stromversorgung 25 - 35 V DC ber Netzteil (Netzteil NT 1015-EU oder NT 1015-120) oder aus einer anderen Gleichstromquelle.

76

Anschlu- und Bedienelemente SZI 1015 HF-Eingang (BNC-Buchse)

Umschalter Mono- / Multichannelbetrieb

HF-Ausgang (BNC-Buchse)

Gewinde fr Stativbefestigung

HF-Klemmanschlu, Eingang (parallel zu )

Klemmanschlu Stromversorgung aus Sender SI 1015 oder ber Netzteil 25 - 35 V (Netzteil NT 1015-EU oder NT 1015-120)

Klemmanschlu Stromversorgung (durchschleifen zum zweiten Strahler SZI 1015)

HF-Klemmanschlu, Ausgang (parallel zu )

1 Zugentlastung Schlieen Sie das Kabel vom Netzteil an der Buchse des Steuersenders SI 1015 an und fhren Sie es durch die Zugentlastung . Der Stecker kann so nicht mehr aus der Buchse herausrutschen und den Betrieb unterbrechen.

Hinweis Eine Zugentlastung ist besonders dann wichtig, wenn das Gert fest in einem Rack eingebaut ist. Im Inneren eines Racks liegen oft sehr viele Leitungen - eine solche Halterung verhindert, da sich die Leitungen gegenseitig herausdrcken.

2 Anschlu der Infrarot-Leistungsstrahler SZI 1015 An den Buchsen und des Steuersenders SI 1015 knnen Sie zwei Leistungsstrahler SZI 1015 anschlieen. Dazu verwenden Sie fertig konfektionierte Koaxial-Kabel mit BNC- Steckern.

Sie knnen auch Koaxial-Kabel ohne Stecker verwenden, die in der Klemmleiste an den Klemmen und befestigt werden. Entfernen Sie dazu am Kabel etwa 20 mm der Kunststoffummantelung und drehen Sie das Geflecht zusammen. Der Mittelleiter mu ca. 10 mm abisoliert werden. Das Geflecht wird an der Masseklemme eingesteckt, der Innen- leiter auen daneben.

Der letzte Strahler eines Zweiges wird mit einem 50 Abschluwiderstand versehen, Da- mit werden stehende Wellen in der HF-Leitung vermieden.

3 Durchschleifen der Stromversorgung zu den Leistungsstrahlern. Bis zu zwei Leistungsstrahler SZI 1015 oder ein SZI 1029-24 knnen ber den Steuersender SI 1015 aus dem Netzteil NT 1015 mit 25-29 V gespeist werden. Dazu steht die Stromversor- gung an den beiden Klemmenpaaren bzw. zur Verfgung. Verbinden Sie die Leistungs- strahler mit diesen Klemmen ber ein zweiadriges Kabel mit je 1,5 mm2 Querschnitt.

98

Elektrisches Zubehr

Anschlukabel GZL 1019 A1

Fr den Anschlu des Strahlers an die Sender SI 1015, SI 29-5 oder SI 1029. Lnge 1 m.

Anschlukabel GZL 1019 A5

Fr den Anschlu des Strahlers an die Sender SI 1015, SI 29-5 oder SI 1029. Lnge 5 m.

Anschlukabe GZL 1019 A10

Fr den Anschlu des Strahlers an die Sender SI 1015, SI 29-5 oder SI 1029. Lnge 10 m.

BNC-Doppelbuchse GZV 1019

Zum Zusammenschalten von zwei Anschluleitungen GZL 1019 A1, -5, -10.

Fr den NF-Anschlu verwenden Sie bitte handelsbliche XLR-3-Anschlukabel in der gewnsch- ten Lnge.

Hinweis: Sennheiser-DruckschriftInfrarot-Planungsbroschre

ber die verschiedenen Einsatzmglichkeiten der Sennheiser-Infrarot-Systeme informiert Sie die Sennheiser-Druckschrift Infrarot-Planungsbroschre. Neben weiterreichenden Informationen ber die Technik der Infrarot-Tonbertragung finden Sie dort auch Anwendungsbeispiele und Kombi- nationen mit bersichtslisten fr Ihre Planung.

Im Rahmen der Produktpflege kann es vorkommen, da nach Redaktionsschlu dieser Druck- schrift technische nderungen der beschriebenen Produkte vorgenommen werden. Wir bitten um Ihr Verstndnis.

Technische Daten SZI 1015 Leistungsstrahler

Anzahl der Sendedioden 66

Mittlere Strahlungsleistung 2 W

Wellenlnge des abgestrahlten Infrarotlichts ca. 880 nm

Trgerfrequenzbereich 30 kHz bis 6 MHz

HF - Eingang 50 mV 5 V / ca. 5 k Eingang / Ausgang BNC - Buchsen / Klemmleisten

Schaltschwelle fr Einschaltautomatik 50 mV

Betriebsspannung 2535 V DC (z.B. aus Netzteil NT 1015) oder aus Steuersender SI 1015

Stromaufnahme 0,75 A bei 25 V

Standby-Betrieb max. 60 mA

Abmessungen in mm ca. 250 x 100 x 80

Gewicht ca. 1,3 kg

SI 1015 Steuersender

Betriebsspannung 25 - 35 V DC (z.B. aus NT 1015)

Stromaufnahme < 140 mA

Abschlu-Impedanz der HF-Ausgnge 50 Trgerfrequenz 1 2,3 MHz Trgerfrequenz 2 2,8 MHz

Eingnge 2 x Audio XLR-3 symmetrisch,

Eingangsempfindlichkeit 50 mV bis 10 V

HF-Ausgnge 2 x BNC, parallel zur Klemmleiste

NT 1015 Netzteil

Netzspannung geregelt 100 - 240 Volt AC

Ausgangsspannung 29 V DC

Ausgangsstrom 1,7 A, ausreichend fr einen Steuersender SI 1015 und zwei Leistungsstrahler SZI 1015 oder einen Steuersender SI 1015 und einen Hochleistungsstrahler SZI 1029-24

1110

SI 1015 SZI 1015INSTRUCTIONS FOR USE

13

12

Connections and operating elements of the SI 1015 (front panel) ON/OFF switch

LED power indicator

Overmodulation indicator channel A

Level control channel A

Overmodulation indicator channel B

Level control channel B

Channel selector switch: channel A channel B channel A/B, 2 x mono channel A and B, stereo

IR transmitting diodes (for direct monitoring via an IR receiver)

Connections and operating elements of the SI 1015 (back panel) RF output socket 1 for connecting a radiator

Barrier strip RF contacts 1 for connecting a radiator (alternative connection to , wired in parallel)

Barrier strip DC outputs for radiator 1

Barrier strip DC outputs for radiator 2

Barrier strip RF contacts 2 for connecting a radiator (alternative connection to , wired in parallel)

RF output socket 2 for connecting a radiator (same signal as )

AF input B

Cable grip

AF input A

Input socket for plug-in mains unit power supply, 25 - 35 V DC via NT 1015 plug-in mains unit or via a different DC source.

1514

Connections and operating elements of the SZI 1015 RF input (BNC socket)

Mono/multi switch

RF output (BNC socket)

Thread for mounting the radiator

Barrier strip RF contacts, input (wired in parallel with )

Barrier strip DC inputs for powering from the SI 1015 modulator or via the NT 1015 plug-in mains unit

Barrier strip DC outputs (for daisy-chaining a second SZI 1015)

Barrier strip RF contacts, output (wired in parallel with )

1 Cable grip Insert the connector of the plug-in mains unit into socket on the SI 1015 modulator and pass the cable through the cable grip as shown. Because of the cable grip, the connector cannot slip out of the socket and interrupt operation.

Note

A cable grip is particularly important when the device is permanently rack mounted. Inside the rack there are often a large number of cables a cable grip prevents the cables from pulling each other out.

2 Rack mounting The SI 1015 can be rack mounted into 1 U of a 19 rack by using accessories GA 1031-AM or GA 1031-CC. The GA 1031-CC is a blank module to bring the SI 1015 to full 19 width, the GA 1031-AM is identical but has additional BNC sockets to bring outputs and to the front panel. The rack mountings are supplied with the SI 1015.

3 Connecting the SZI 1015 radiators Sockets and on the SI 1015 modulator can be used to connect two SZI 1015 power radiators. For connecting the radiators, use ready made up co-axial cables with BNC connectors.

You can also use a co-axial cable without a connector. The cable has to be inserted into contacts and of the barrier strip. Remove approx. 20 mm of the cables cuter jacket, twist the screen into a little roll, and pull it to one side. Strip the central wire by approx. 10 mm. Insert the screen into the ground terminal and the central wire into the indicated contact on the barrier strip.

4 Daisy-chaining the radiators Two SZI 1015 power radiators or one SZI 1029-24 high power radiator can be 25-29 V DC powered by the NT 1015 plug-in mains unit via the SI 1015 modulator. The supply voltage is output via the two contact pairs +. Connect the radiators to the contacts by using a two-wire cable with a cross section of 1.5 mm2 per wire.

1716

Accessoires

GZL 1019 A1 BNC/BNC co-axial cable

For connecting a radiator to the SI 1015, SI 29-5 or SI 1029 transmitters. Length: 1 m.

GZL 1019 A5 BNC/BNC co-axial cable

For connecting a radiator to the SI 1015, SI 29-5 or SI 1029 transmitters. Length: 5 m.

GZL 1019 A10 BNC/BNC co-axial cable

For connecting a radiator to the SI 1015, SI 29-5 or SI 1029 transmitters. Length: 10 m.

GZV 1019 BNC coupler

for connecting two GZL 1019 A1, -5, -10 co-axial cables.

GA 1031-AM blank module

For 19 rack mounting (with BNC sockets).

GA 1031-CC blank module

For 19 rack mounting.

For the AF connection, use a standard XLR-3 connection cable of the required length.

Note: IR Planning Brochure from Sennheiser

Information on the many possible areas of application of Sennheiser infra-red audio transmission systems can be found in the IR Planning Brochure. This brochure gives detailed information on infra-red transmission technology and contains application examples as well as possible product combinations and overviews for infra-red system planning.

Since we are continually trying to improve our products it may happen that technical alterations are made on the described products after this manual has gone to press. We apologise for any inconvenience.

Technical Data SI 1015 Modulator

Operating voltage 24 - 35 V DC (via NT 1015)

Current consumption < 140 mA

Terminating impedance of the RF outputs 50 Carrier frequency 1 2.3 MHz Carrier frequency 2 2.8 MHz

Inputs 2 x XLR-3, balanced

Input sensitivity 50 mV 5 V

RF outputs 2 x BNC, in parallel with barrier strip

SZI 1015 Power radiator

Number of transmitting diodes 66

Average radiating power 2 W

Wavelength of radiated infra-red light approx. 880 nm

Carrier frequency range 30 kHz 6 MHz

RF input level 50 mV 3 V / approx. 5 k Inputs / outputs BNC sockets / barrier strip

Threshold voltage for automatic on/off function 50 mV

Operating voltage 2535 V DC via NT 1015 plug-in mains unit or via SI 1015 modulator

Current consumption 0.75 A at 25 V

Stand-by max. 60 mA

Dimensions in mm approx. 250 x 100 x 80

Weight approx. 1.3 kg

NT 1015 Plug-in mains unit

Mains voltage 100 240 V AC without switching

Output voltage 29 V DC

Output current 1.7 A, for powering an SI 1015 modulator and two SZI 1015 power radiators or an SI 1015 modulator and one SZI 1029-24 high power radiator

1918

SI 1015 SZI 1015NOTICE DEMPLOI

21

20

Commandes et raccordements du SI 1015 (partie frontale) Interrupteur Marche/Arrt

LED tension secteur

Indication de surmodulation canal A

Rglage du niveau canal A

Indication de surmodulation canal B

Rglage du niveau canal B

Commutateur pour slection de canal: canal A

canal B canal A/B, 2 x mono canal A et B, stro

Diodes dmission infrarouges (pour le contrle direct par un rcepteur infrarouge)

Commandes et raccordements du SI 1015 (partie arrire) Connecteur de sortie HF 1, raccordement pour diffuseur

Bornier de sortie HF 1, raccordement pour diffuseur (en parallle )

Bornier de sortie 1 alimentation DC pour diffuseur (chanage de )

Bornier de sortie 2 alimentation DC pour diffuseur (chanage de )

Bornier de sortie HF 2, raccordement pour diffuseur (en parallle )

Connecteur de sortie HF 2, raccordement pour diffuseur (le mme signal que )

Entre BF B

Bride de retenue

Entre BF A

Raccordement alimentation alimentation 25 - 35 V DC par bloc-secteur NT 1015-EU ou NT 1015-120 ou par une autre source DC.

2322

Commandes et raccordements du SZI 1015 Entre HF (prise BNC)

Commutateur mono/multi

Sortie HF (prise BNC)

Filetage pour fixation sur pied

Bornier dentre HF (en parallle )

Bornier dentre alimentation DC alimentation par modulateur SI 1015 ou par bloc-secteur NT 1015-EU ou NT 1015-120

Bornier de sortie alimentation DC (pour raccorder en chane un deuxime SZI 1015)

Bornier de sortie HF (en parallle )

1 Bride de retenue Insrer le connecteur du bloc-secteur dans la prise du modulateur, puis passer le cble dans la bride de retenue pour viter toute traction sur la prise. Ceci garantit une fixation de scurit dans la prise et vite tout risque dinterruption du fonctionnement.

Nota:

La bride de retenue est particulirement importante lorsque lappareil se trouve intgr un rack de montage parce que, dans ce cas, il y a prsence dune quantit de fils et quil est ainsi vit que les conducteurs, pesant les uns sur les autres, naffectent la connexion de la prise.

2 Raccordement des diffuseurs de puissance SZI 1015 Sur les sorties et du modulateur SI 1015, deux diffuseurs de puissance SZI 1015 peuvent tre raccords. Pour la liaison entre modulateur et diffuseur, utiliser un cble coaxial connecteur BNC. Sennheiser fournit des cbles coaxiaux tous prts, longeur 1 m, 5 m et 10 m.

Il est galement possible dutiliser un cble coaxial sans connecteur, qui doit alors tre insr dans les sorties et du bornier. Pour ce faire, retirer environ 20 mm de lenveloppe en plastique du cble, torsader le blindage et le tirer de ct. Dnuder le fil de masse denviron 10 mm. Insrer le blindage torsad dans la borne de mise la terre, puis insrer le fil de masse dans la sortie du bornier.

3 Raccordement en chane des diffuseurs Deux diffuseurs de puissance SZI 1015 ou un diffuseur haute puissance SZI 1029-24 peuvent tre aliments, par le biais du modulateur SI 1015, depuis le bloc-secteur NT 1015. A cet effet, la tension dalimentation est prsente aux sorties . Pour relier les diffuseurs ces sorties, utiliser un cble deux conducteurs avec une section transversale de 1,5 mm2 par conducteur.

2524

Accessoires

Cble de raccordement GZL 1019 A1

Destin relier le diffuseur aux metteurs SI 1015, SI 29-5 ou SI 1029. Longueur: 1 m.

Cble de raccordement GZL 1019 A5

Destin relier le diffuseur aux metteurs SI 1015, SI 29-5 ou SI 1029. Longueur: 5 m.

Cble de raccordement GZL 1019 A10

Destin relier le diffuseur aux metteurs SI 1015, SI 29-5 ou SI 1029. Longueur: 10 m.

Connecteur double BNC GZV 1019

Destin relier deux cbles de raccordement GZL 1019 A1, -5, -10.

Pour la connection BF, veuillez utilisez un cble de raccordement XLR-3 la longueur desire.

Nota: La brochure Conception de Projets en Transmission Infrarouge de Sennheiser

Pour vous informer plus avant sur les differents domaines dapplications des systmes infrarouges Sennheiser, demandez notre brochure Conception de Projets en Transmission Infrarouge. Outre de plus amples informations sur la technique de transmission infrarouge, vous y trouverez des exemples pratiques et des conseils pour la conception de vos projets.

Dans loptique dune amlioration permanente de ses produits, Sennheiser se rserve le droit de modifier les caractristiques techniques des produits dcrits dans la prsente notice demploi.

Caractristiques techniques SZI 1015 Diffuseur de puissance

Nombre de diodes dmission 66

Puissance moyenne de rayonnement 2 W

Longueur donde de la lumire infrarouge rayonne approx. 880 nm

Plage de frquences porteuses 30 kHz 6 MHz

Entre HF 50 mV 5 V / approx. 5 k Entres / sorties prises BNC / borniers

Tension seuil de mise en circuit automatique 50 mV

Alimentation 25 35 V DC par bloc-secteur NT 1015 ou par modulateur SI 1015

Consommation 0,75 A 25 V

Mode stand-by max. 60 mA

Dimensions en mm approx. 250 x 100 x 80

Poids approx. 1,3 kg

SI 1015 Modulateur

Alimentation 25 - 35 V DC (par NT 1015)

Consommation < 140 mA

Impdance de charge aux sorties HF 50 Frquence porteuse 1 2,3 MHz

Frquence porteuse 2 2,8 MHz

Entres 2 x XLR-3, symtrique

Sensibilit dentre 50 mV 10 V

Sorties HF 2 x BNC, parallle au bornier

NT 1015 Bloc-secteur

Tension secteur 100 - 240 V AC (commutation automatique)

Tension de sortie 29 V DC

Courant de sortie 1,7 A, pour alimenter un modulateur SI 1015 et deux diffuseurs SZI 1015 ou un modulateur SI 1015 et un diffuseur haute puissance SZI 1029-24

2726

SI 1015 SZI 1015ISTRUZIONI PER LUSO

29

28

Collegamento e uso dellSI 1015 (parte anteriore) tasto ON / OFF

LED per il controllo dallacciamento alla rete

Indicazione di sovramodulazione canale A

Indicatore di livello canale A

Indicazione di sovramodulazione canale B

Indicatore di livello canale B

Commutatore: canale A canale B canale A / B due volte mono canale A e B come segnale stereo

Diodi di trasmissione-IR (per il controllo diretto con un ricevitore IR)

Collegamento e uso dellSI 1015 (Parte posteriore) Presa duscita 1 per RF, collegamento del radiatore di potenza

Presa a morsetto 1 per RF, collegamento del radiatore di potenza (collegato in parallelo a )

Presa 1 collegamento dellalimentatore per il radiatore di potenza (collegato in serie con )

Presa 2 collegamento dellalimentatore per il radiatore di potenza (collegato in serie con )

Presa a morsetto 2 per RF, collegamento del radiatore di potenza (collegato in parallelo a )

Presa duscita 2 per RF, collegamento del radiatore di potenza (stesso segnale come )

Entrata BF B

Dispositivo anti trazione

Entrata BF A

Collegamento alla rete attraverso lalimentatore (Alimentatore NT1015, NT 1015-120 o NT 1015-240) o da un altra rete a bassa tensione

3130

Collegamento e uso dellSZI 1015 Entrata RF (presa BNC)

Commutatore Mono- o multicanale

Uscita RF (presa BNC)

Dispositivo con filettatura per il fissaggio dello stativo

Collegamento a morsetto per RF, Entrata (collegato in parallelo a)

Collegamento a morsetto per lalimentatore (dal trasmettitore SI 1015 o attraverso lalimentatore 25-35 V (Alimentatore NT 1015, NT 1015-120 o NT 1015-240)

Collegamento a morsetto per lalimentatore (collegare in serie con il secondo radiatore SZI 1015)

Collegamento a morsetto per RF, Uscita (collegato in parallelo a )

1 Dispositivo anti trazione Collegate il cavo dellalimentatore alla presa del trasmettitore di comando SI1015 e fissatelo nel dispositivo anti-trazione . Si evita cosi che la presa perda il contatto e che il funzionamento venga interrotto.

Nota

Lo scarico di trazione di particolare importanza se lapparecchio montato in maniera fissa allinterno di un rack. In questo infatti sono collegati spesso molti cavi e questo dispositivo fa si che i cavi non si scollegano luno con laltro.

2 Collegamento dei radiatori di potenza a raggi infrarossi SZI 1015 Alle prese e del trasmettitore di comando SI 1015 possono essere collegati due radiatori SZI1015. Per questo usate dei cavi coassiali gi confezionati con presa del tipo BNC.

Potete anche usare dei cavi coassiali senza presa e fissarli direttamente nei morsetti e . Per fare ci eliminate circa 20 mm dellisolamento in plastica e attorcigliate linsieme dei cavi per ottenere una unit compatta. Il conduttore neutro deve essere isolato per circa 10 mm. Linsieme dei cavi viene fissato nella morsetteria, il conduttore neutro allesterno.

3 Collegamento in serie dellalimentatore ai radiatori di potenza Attraverso il trasmettitore di comando SI 1015 possono essere alimentate due radiatori SZI 1015 dallalimentatore NT1015 con 25-29 V. Per questo la tensione di alimentazione deve essere prelevata dalla coppia di morsetti . Collegate i radiatori di potenza con un cavetto doppio con circa 2 x 1,5 mm diametro ai morsetti.

3332

Dati tecnici SZI 1015 Radiatore di potenza

Numeri dei diodi di trasmissione 66

Potenza irradiata media 2 W

Lunghezza donda della luce infrarossa irradiata ca. 880 mm

Gamma frequenze portanti 30 kHz bis 6 Mhz

Entrata RF 50 mV -5 V / circa 5 kW

Entrata / uscita Prese BNC / morsetteria

Soglia per linserimento automatico 50 mV

Tensione di alimentazione 25-35 V tensione continua dallalimentatore NT 1015 o dal trasmettitore di comando SI1015

Corrente assorbita circa 0,75 A in caso di 25 V

in modo stand-by massimo 60 mA

Dimensioni in mm circa 25 x 100 x 80

Peso circa 1,3 kg

SI 1015 trasmettitore di comando

Tensione di alimentazione 25-35 V tensione continua (dal NT 1015)

Corrente assorbita <140 mA

Impedenza delle uscite RF 50 W

Frequenza portante 1 2,3 MHz Frequenza portante 2 2,8 MHz

Entrate 2 x audio XLR-3, simmetrico

Livello di sensibilit 50 mV fino a 10 V

Uscite RF 2 x BNC, collegati in parallelo alla morsetteria

NT1015 Alimentatore

Tensione dalimentazione regolata 100 - 240 Volt AC

Tensione duscita 29 Volt DC

Potenza circa 2 A, sufficiente per un trasmettitore di comando SI 1015 e due radiatori di potenza SZI 1015.

Accessori elettrici

Cavo di collegamento GZL 1019 A1

Per il collegamento del radiatore ai trasmettitori SI 1015, , SI 29-5 o SI 1029, lunghezza 1 m

Cavo di collegamento GZL 1019 A5

Per il collegamento del radiatore ai trasmettitori SI 1015, , SI 29-5 o SI 1029, lunghezza 5 m

Cavo di collegamento GZL 1019 A10

Per il collegamento del radiatore ai trasmettitori SI 1015, , SI 29-5 o SI 1029, lunghezza 10 m

Presa doppia BNC GZV 1019

Per lallacciamento di 2 cavi di collegamento GZL 1019 A1, -5, -10

Per il collegamento BF usate un cavo di collegamento XLR-3 reperibile in commercio nella lunghezza richiesta.

Nota: Brochure informativa Sennheiser dei sistemi a raggi infrarossi

La brochure informativa sistemi a raggi infrarossi della Sennheiser da informazioni sui diversi impieghi dei sistemi ad infrarossi della Sennheiser. Oltre ad informazioni sulla tecnica di trasmissione ad infrarossi trovate anche esempi di impieghi e combinazioni per la progettazione del Vostro impianto.

Nel quadro di miglioramento dei prodotti possono venire apportate modifiche tecniche ai prodotti descritti dopo la chiusura redazionale di questo opuscolo. Vi chiediamo gentilmente di scusarci.

3534

SI 1015 SZI 1015INSTRUCCIONES PARA EL USO

37

36

Elementos de conexin y mando del SI 1015 (cara frontal) Interruptor principal

LED de control de conexin a la red

Indicacin de sobremodulacin del canal A

Regulador de nivel del canal A

Indicacin de sobremodulacin del canal B

Regulador de nivel del canal A

Interruptor selector: Canal A Canal B Canal A y B: dos monofnicos Canal A y B como seal estereofnica

Diodos transmisores IR (para control directo con un receptor de IR)

Elementos de conexin y mando del SI 1015 (cara dorsal) Jack de salida de AF, conexin para radiador de potencia

Conexin a presin AF, conexin para radiador de potencia (paralelo a )

Conexin 1, alimentacin de corriente para radiador de potencia (paso en bucle desde )

Conexin 2, alimentacin de corriente para radiador de potencia (paso en bucle desde )

Conexin a presin AF 2, conexin para radiador de potencia (paralelo a )

Jack de salida de AF, conexin para radiador de potencia (seal idntica a )

Entrada de BF B

Dispositivo de contratraccin

Entrada de BF A

Conexin para alimentacin de corriente de 25-35 V a travs de bloque de alimentacin (bloque de alimentacin NT 1015, NT 1015-120 NT 1015-240), o tomada de otra red de baja tensin.

3938

Elementos de conexin y mando del SZI 1015 Entrada de AF (jack BNC)

Conmutador para funcionamiento monofnico / multicanal

Salida de AF (jack BNC)

Rosca para fijar un trpode

Conexin a presin de AF, entrada (paralela a )

Conexin a presin para alimentacin de corriente (del transmisor SI 1015 o por medio de bloque de alimentacin de 25-35 V (bloque de alimentacin NT 1015, NT 1015-120 NT 1015-240)

Conexin a presin para alimentacin de corriente (paso en bucle al segundo radiador SZI 1015)

Conexin a presin de AF, salida (paralela a )

1 Dispositivo de contratraccin Conecte el cable del bloque de alimentacin al jack del transmisor de mando SI 1015; pase el cable a travs del dispositivo de contratraccin . Esto impide que la clavija pueda salirse del jack, interrumpindose el funcionamiento.

Nota

El dispositivo de contratraccin es especialmente importante cuando el equipo ha de montarse fijamente en un bastidor pues, a menudo, en el interior de ste hay muchos cables. Una pinza de este tipo impide que los cables se desenchufen.

2 Conexin del radiador de potencia por infrarrojos SZI 1015 A los jacks y del transmisor de mando SI 1015 puede conectar Vd. dos radiadores de potencia SZI 1015. Utilice cables coaxiales ya confeccionados, con clavijas BNC.

Tambin puede emplear cables coaxiales sin clavija, que se fijan a la regleta de bornes en los bornes y . Retire del cable unos 20 mm del revestimiento de plstico; tuerza el trenzado para formar un rollito. El conductor central debe quedar sin aislamiento unos 10 mm, aproximadamente. El trenzado se calar en el borne a masa y el conductor interior al lado, afuera.

3 Conexin en bucle de la alimentacin de corriente a los radiadores de potencia A travs del bloque de alimentacin NT 1015 pueden alimentarse con 25-29 V hasta dos radiadores de potencia SZI 1015. A tal fin se retira la tensin de alimentacin de ambos pares de bornes /. Conecte los radiadores de potencia con estos bornes a travs de un conductor dividido de unos 2 x 1,5 mm .

4140

Accesorios elctricos

Cable conector GZL 1019A1

Para conectar el radiador a los transmisores SI 1016, SI 29-5 SI 1029. Largo: 1 m.

Cable conector GZL 1919A5

Para conectar el radiador a los transmisores SI 1015, SI 29-5 SI 1029. Largo: 5 m.

Cable conector GZL 1019 A10

Para conectar el radiador a los transmisores SI 1015, SI 29-5 SI 1029. Largo: 10 m.

Jack doble BNC GZV 1019

Para interconectar dos cables conectores GUL 1019 A1, 1019 A5, 1019 A10.

Para la conexin de BF, emplear un cable conector XLR-3, corriente en el comercio, del largo deseado.

Nota: Impreso Folleto sobre planificacin de sistemas infrarrojos de Sennheiser

El Folleto sobre planificacin de sistemas infrarrojos de Sennheiser informa acerca de las diferentes posibilidades de utilizacin de los sistemas infrarrojos de Sennheiser. Adems de detalladas informaciones acerca de la tcnica de transmisin del sonido por infrarrojos, encontrar Vd. tambin diferentes ejemplos de aplicacin, as como listas de combinaciones e informacin general que facilitan dicha planificacin.

Por su constante perfeccionamiento de los productos, puede suceder que despus de terminada la impresin de este folleto, se efecten modificaciones tcnicas de los productos aqu descritos, por lo cual rogamos su comprensin.

Datos tcnicos SZI 1015 Radiador de potencia

Nmero de diodos transmisores 66

Potencia mnima de radiacin 2 W

Longitud de onda de la luz infrarroja irradiada aprox. 880 mm

Margen de frecuencia portadora 30 kHz hasta 6 MHz

Entrada AF 50 mV - 5 V/aprox. 5 kW

Entrada / Salida Jacks BNC / Regletas de bornes de fijacin

Onda de conexin para mecanismo automtico de conexin 50 mV

Tensin de servicio 25-35 V, corriente continua del bloque de alimentacin NT 1015 del transmisor de mando SI 1015

Consumo de corriente aprox. 0,75 A a 25 VO

Servicio stand-by mx. 60 mA

Dimensiones en mm aprox. 250 x 100 x 80

Peso aprox. 1,3 kg

S-1015 Transmisor de mando

Tensin de servicio 25-35 voltios, corriente continua (del NT 1015)

Consumo de corriente < 140 mA

Impedancia final de las salidas de AF 50W

Frecuencia portadora 1 2,3 MHz Frecuencia portadora 2 2,8 MHz

Entradas 2 x Audio XLR-3, simtricas

Sensibilidad de entrada 50 mV hasta 10 V

Salidas AF 2 x BNC, paralelas en la regleta de bornes

NT 1015 Bloque de alimentacin

Tensin de la red regulada 100 - 240 voltios, CC

Tensin de salida 29 voltios DC

Potencia aprox. 2 A, suficientes para un transmisor de mando SI 1015 y dos radiadores de potencia SZI 1015

4342

SI 1015 SZI 1015GEBRUIKSAANWIJZING

45

44

Aansluit- en bedieningselementen SI 1015 (voorzijde) Aan-/uit-schakelaar

Netspanningscontrole LED

Overmodulatie-aanduiding kanaal A

Niveau-instelling kanaal A

Overmodulatie-aanduiding kanaal B

Niveau-instelling kanaal B

Keuzeschakelaar: kanaal A kanaal B kanaal A en B gemengd mono kanaal A en B als stereosignaal

IR-zenddioden (voor directe controle door een IR-ontvanger)

Aansluit- en bedieningselementen SI 1015 (achterzijde) HF-uitgangsbus 1, aansluiting voor vermogensstraler

HF-klemaansluiting 1, aansluiting voor vermogensstraler (parallel aan ?)

Aansluiting 1 voedingsspanning vermogensstraler (doorgelust van ?)

Aansluiting 2 voedingsspanning vermogensstraler (doorgelust van ?)

HF-klemaansluiting 2, aansluiting voor vermogensstraler (parallel aan ?)

HF-uitgangsbus 2, aansluiting voor vermogensstraler (zelfde signaal als ?)

NF-ingang B

Trekontlasting

NF-ingang A

Aansluiting voedingsspanning 25-35 V via voeding (voeding NT 1015, NT 1015-120 of NT 1015-240) of uit een ander laagspanningsnet.

4746

Aansluit- en bedieningselementen SZI 1015 HF-ingang (BNC-bus)

Schakelaar mono-/multikanaalwerking

HF-uitgang (BNC-bus)

Schroefdraad voor statiefbevestiging

HF-klemaansluiting, ingang (parallel aan )

Klemaansluiting voedingsspanning (uit zender SI 1015 of via voeding 25-35 V (voeding NT 1015, NT 1015-120 of NT 1015-240))

Klemaansluiting voedingsspanning (doorlussen naar tweede straler SZT 1015)

HF-klemaansluiting, uitgang (parallel aan )

1 Trekontlasting Steek de netvoedingskabel in de bus van de stuurzender SI 1015 en leid de kabel door de trekontlasting . De stekker kan zo niet meer uit de bus worden getrokken, zodat de werking niet wordt onderbroken.

Opmerking Een trekontlasting is vooral van belang, wanneer het apparaat vast in een rack is ingebouwd. Binnenin het rack liggen vaak veel kabels - een dergelijke bevestiging voorkomt, dat de kabels elkaar uit de bussen drukken.

2 Aansluiting van de infrarood-vermogensstraler SZI 1015 Op de bussen en van de stuurzender SI 1015 kunt u twee vermogensstralers SZI 1015 aansluiten. Gebruik hiervoor kant-en-klare coax-kabels met BNC-stekkers.

U kunt ook coax-kabels zonder stekker gebruiken, die in de klemlijst aan de klemmen en worden bevestigd. Verwijder daartoe ongeveer 20 mm van de kunststof mantel aan het uiteinde van de kabel en draai het vlechtwerk in elkaar tot een streng. Verwijder ca. 10 mm isolatie van de middenleider. Steek het vlechtwerk in de aardklem, de middenleider aan de buitenkant daarnaast.

3 Doorlussen van de voedingsspanning naar de vermogensstralers Er kunnen max. twee vermogensstralers SZI 1015 via de stuurzender SI 1015 door de voeding NT 1015 met 25-29 V worden gevoed. Daartoe is de voeding van de beide klemmenparen / uitgetrokken. Sluit de vermogensstralers via een dubbele kabel met een diameter van ca. 2 x 1,5 mm op deze klemmen aan.

4948

Technische gegevens

SZI 1015 Vermogensstraler

Aantal zenddioden 66 Gemiddeld uitstralingsvermogen 2 W

Golflengte van het uitgestraalde infraroodlicht ca. 880 nm

Draagfrequentiebereik 30 kHz tot 6 MHz

HF-ingang 50 mV - 5 V/ca. 5 k Ingang/uitgang BNC-bussen/klemlijsten

Schakeldrempel voor inschakelautomaat 50 mV

Voedingsspanning 25-35 V gelijkspanning uit voeding NT 1015 of uit stuurzender SI 1015

Stroomopname ca. 0,75 A bij 24 VO

Stand-by werking max. 60 mA

Afmetingen in mm ca. 250 x 100 x 80

Gewicht ca. 1,3 kg

SI 1015 Stuurzender

Voedingsspanning 25-35 V gelijkstroom (uit NT 1015)

Stroomopname <140 mA

Afsluit-impedantie van de HF-uitgangen 50 W

Draagfrequentie 1 2,3 MHz

Draagfrequentie 2 2,8 MHz

Ingangen 2 x audio XLR-3 symmetrisch

Ingangsgevoeligheid 50 mV tot 10 V

HF-uitgangen 2 x BNC, parallel daaraan aan klemlijst

NT 1015 Voeding

Voedingsspanning geregeld 100 - 240 V AC

Uitgangsspanning 29 V DC

Vermogen ca. 2 A, voldoende voor een stuurzender SI 1015 en twee vermogensstralers SZI 1015

Elektrische accessoires

Aansluitkabel GZL 1019 A1 Voor de aansluiting van de straler op de zenders SI 1015, SI 29-5 of SI 1029. Lengte 1 m.

Aansluitkabel GZL 1019 A5

Voor de aansluiting van de straler op de zenders SI 1015, SI 29-5 of SI 1029. Lengte 5 m.

Aansluitkabel GZL 1019 A10

Voor de aansluiting van de straler op de zenders SI 1015, SI 29-5 of SI 1029. Lengte 10 m.

BNC-dubbele bus GZV 1019 Voor het samenvoegen van twee aansluitkabels GZL 1019 A1, -5, -10.

Gebruik voor de NF-aansluiting een in de handel verkrijgbare XLR-3 aansluitkabel in de gewenste lengte.

Opmerking: Sennheiser-brochure Infrarood-planningsbrochure

De Sennheiser-brochure Infrarood-planningsbrochure geeft informatie over de verschillende toepassingen van de Sennheiser infraroodsystemen. Naast uitgebreide informatie over de techniek van de infrarood-geluidsoverdracht vindt u ook gebruiksvoorbeelden en combinatie- en overzichtslijsten voor uw planning.

In het kader van de productverbetering kan het voorkomen, dat na het sluiten van de redactie van deze brochure technische wijzigingen aan de beschreven producten zijn aangebracht. Wij vragen uw begrip hiervoor.

5150

Aktuelle Informationen zu Sennheiser-Produkten erhalten Sie auch im Internet unter http://www.sennheiser.com.

Up to date information on Sennheiser products can also be found on the Internet at http://www.sennheiser.com.

Vous trouverez galement toutes les informations actuelles relatives aux produits Senn- heiser sur Internet, sous http://www.sennheiser.com.

Informazioni attuali sulla gamma di prodotti Sennheiser sono disponibili anche in Internet al sito http://www.sennheiser.com.

Tambin en Internet, bajo http://www.sennheiser.com obtendr Vd. informaciones actuales sobre los productos Sennheiser.

Actuele informatie met betrekking tot Sennheiser producten vindt u ook op Internet onder http://www.sennheiser.com.

Konformittserklrung

Sennheiser electronic GmbH & Co. KG erklren, da dieses Gert die an-wendbaren CE-Normen und Vorschriften erfllt.

Approval

Sennheiser electronic GmbH & Co. KG declare that this device is in com-pliance with the applicable CE standards and regulations.

Certification

Sennheiser electronic GmbH & Co. dclarons que cet appareil est en con-formit avec les normes CE.

Certificazione

Sennheiser electronic GmbH & Co. KG dichiara che questo apparecchio risponde alle normative e alle prescrizioni CE applicabili.

Autorizacion

Sennheiser electronic GmbH & Co. KG declara que este aparato cumple las normas y directrices de la CE aplicables.

Vergunning

Sennheiser electronic GmbH & Co. KG verklaren, dat di

Manualsnet FAQs

If you want to find out how the SZI 1015 Sennheiser works, you can view and download the Sennheiser SZI 1015 Instruction Manual on the Manualsnet website.

Yes, we have the Instruction Manual for Sennheiser SZI 1015 as well as other Sennheiser manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Instruction Manual should include all the details that are needed to use a Sennheiser SZI 1015. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Sennheiser SZI 1015 Instruction Manual is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Sennheiser SZI 1015 Instruction Manual consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Sennheiser SZI 1015 Instruction Manual free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Sennheiser SZI 1015 Instruction Manual, simply download the document to your computer. Once downloaded, open the PDF file and print the Sennheiser SZI 1015 Instruction Manual as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.