Sencor ONE BLATNIK Mudguard User Manual PDF

1 of 2
1 of 2

Summary of Content for Sencor ONE BLATNIK Mudguard User Manual PDF

EN Scooter One Replacement Mudguard with Light

Package contents: A 1x rear mudguard with tail light B 1x mudguard bracket C 2x side plastic cover D 2x reflective sticker E 2x M5 screw for attaching the mudguard bracket to the

scooter frame F 2x M5 screw washer G 1x self-tapping screw for mounting the bracket I 1x tail light extension wire (in case of replacement) J 2x shrink tube for the tail light wire connector

Removing the existing mudguard from Scooter One 1) Remove the side plastic caps . First peel off the

stickers from the plastic caps and loosen the caps Allen screws. Tip: to peel off, gently heat the stickers with a hair dryer to loosen the adhesive and peel them off.

2) Remove the rear wheel. Loosen the rear wheel attached with Allen screws on both sides . After removing the Allen screws, pull the wheel in the opposite direction of travel to remove the entire wheel from the scooter body OUT.

3) Turn Scooter One upside down to remove the existing rear mudguard. Loosen the 3 screws holding the mudguard to the scooter body . Carefully disconnect the tail light power lead at the connector .

Fitting a new mudguard on Scooter One 1) Fasten mudguard B with 3x disassembled screws.

Do not tighten the screws firmly yet! Connect the tail light power lead . Before connecting the connector, put one shrink tube J on the wire. Connect the connectors and pull through the shrink tube. Check that the tail light is working by switching on the scooter. Turn off the scooter to continue mounting the fender. Use a heat source to achieve shrinkage. Warning: Take care when working with the heat source! The radiated heat must not come close to any part of the scooter except the shrink tube covering the connector. Handle the heat in such a way as to avoid personal injury and damage to property.

2) Attach the mudguard bracket B to the mudguard using screw G. Use your Phillips screwdriver to attach. After centring the mudguard bracket B on the holes to the scooter body, tighten the screw G firmly. It will not be possible to tighten the G screw later.

3) Insert the previously dismantled wheel into the Scooter One body. Use the screws E to attach the bracket B to the rear wheel hub. Screw E|washer F|bracket B|scooter body|hub. Tighten firmly!!!

4) Tighten the mudguard screws . 5) Attach the caps C and re-stick them with the reflective

sticker D. Make sure that the tail light and brake light are working and that the screws are tightened so that they are not loosened by driving. Keep checking that all screws are tight. Check that the rear wheel is not touching the mudguard or the tail light lead.

CZ Nhradn blatnk pro Scooter One

Obsah balen: A 1x zadn blatnk se zadnm svtlem B 1x drk blatnku C 2x bon plastov krytka D 2x reflexn samolepka E 2x M5 roub uchycen drku blatnku k rmu kolobky F 2x podloka roubu M5 G 1x samoezn roub uchycen drku k blatnku I 1x prodluovac vodi zadnho svtla (pro ppad nutn

vmny) J 2x smrovac burka propojovacho konektoru vodie

zadnho svtla

Odejmut stvajcho blatnku z kolobky Scooter One 1) Demontujte bon plastov krytky . Nejprve

sloupnte z plastovch krytek samolepky a povolte imbusov rouby krytek. Tip: pro sloupnut jemn nahejte samolepky fnem, aby povolilo lepidlo a sloupnte je.

2) Demontujte zadn kolo. Povolte zadn kolo uchycen imbusovmi rouby na obou stranch . Po vyjmut imbusovch roub tahem kola v protismru jzdy vyjmte cel kolo z tla kolobky OUT.

3) Otote Scooter One koly vzhru pro demont stvajcho zadnho blatnku. Povolte 3x rouby drc blatnk k tlu kolobky . Opatrn odpojte napjec vodi zadnho svtla v mst konektoru .

Mont novho blatnku na kolobku Scooter One 1) Upevnte blatnk B pomoc 3x roub demontovan.

Zatm nedotahujte rouby napevno! Pipojte napjec vodi zadnho svtla . Ped spojenm konektoru navlknte na vodi jednu smrovac burku J. Spojte konektory a pethnte smrovac burkou. Zapnutm kolobky ovte funknost zadnho svtla. Vypnte kolobku pro pokraovn monte blatnku. Pro doclen smrtn burky pouijte zdroj tepla.Upozornn: Pi prci se zdrojem tepla, dbejte opatrnosti! Vyzaovan teplo se nesm piblit k dn sti kolobky krom smrujc burky pekrvajc konektor. S teplem zachzejte tak aby nedolo k jm na zdrav osob a pokozen majetku.

2) K blatnku pipevnte roubem G drk blatnku B. K pipevnn pouijte v kov roubovk. Po vycentrovn drku blatnku B na otvory k tlu kolobky dothnte roub G napevno. Pozdji nebude mon G roub dothnout.

3) Vlote ji dve demontovan kolo do tla Scooter One. rouby E pipevnte chyt B k nboji zadnho kola. roub E|podloka F|drk B|tlo kolobky|nboj. Pevn dothnte!!!

4) Dothnte rouby blatnku . 5) Pipevnte krytky C a pelepte je reflexn samolepkou

D.

Ujistte se, e je funkn zadn svtlo, brzdov svtlo a jsou dotaen rouby tak aby nedolo k jejich povolen vlivem jzdy. Prbn kontrolujte dotaen vech roub. Zkontrolujte, e zadn kolo se nedotk blatnku ani vodie zadnho svtla.

SK Nhradn blatnk pre Scooter One

Obsah balenia: A 1 zadn blatnk so zadnm svetlom B 1 driak blatnka C 2 bon plastov krytka D 2 reflexn samolepka E 2 M5 skrutka uchytenia driaka blatnka k rmu

kolobeky F 2 podloka skrutky M5 G 1 samorezn skrutka uchytenia driaka k blatnku I 1 predlovac vodi zadnho svetla (pre prpad nutnej

vmeny) J 2 zmrovacia burka prepojovacieho konektora vodia

zadnho svetla

Odobratie existujceho blatnka z kolobeky Scooter One 1) Demontujte bon plastov krytky . Najprv zlpnite

z plastovch krytiek samolepky a povote imbusov skrutky krytiek. Tip: na zlpnutie jemne nahrejte samolepky fnom, aby povolilo lepidlo a zlpnite ich.

2) Demontujte zadn koleso. Povote zadn koleso uchyten imbusovmi skrutkami na oboch stranch . Po vybrat imbusovch skrutiek ahom kolesa v protismere jazdy vyberte cel koleso z tela kolobeky OUT.

3) Otote Scooter One kolesami nahor na demont existujceho zadnho blatnka. Povote 3 skrutky driace blatnk k telu kolobeky . Opatrne odpojte napjac vodi zadnho svetla v mieste konektora .

Mont novho blatnka na kolobeku Scooter One 1) Upevnite blatnk B pomocou 3 skrutiek demontovan.

Zatia nedoahujte skrutky napevno! Pripojte napjac vodi zadnho svetla . Pred spojenm konektora navlete na vodi jednu zmrovaciu burku J. Spojte konektory a pretiahnite zmrovacou burkou. Zapnutm kolobeky overte funknos zadnho svetla. Vypnite kolobeku na pokraovanie monte blatnka. Na docielenie zmrtenia burky pouite zdroj tepla. Upozornenie: Pri prci so zdrojom tepla dbajte na opatrnos! Vyarovan teplo sa nesmie pribli k iadnej asti kolobeky okrem zmrujcej burky prekrvajcej konektor. S teplom zaobchdzajte tak, aby nedolo k ujme na zdrav osb a pokodeniu majetku.

2) K blatnku pripevnite skrutkou G driak blatnka B. Na pripevnenie pouite v krov skrutkova. Po vycentrovan driaka blatnka B na otvory k telu kolobeky dotiahnite skrutku G napevno. Neskr nebude mon G skrutku dotiahnu.

3) Vlote u predtm demontovan koleso do tela kolobeky Scooter One. Skrutkami E pripevnite chyt B k nboju zadnho kolesa. Skrutka E|podloka F|driak B|telo kolobeky|nboj. Pevne dotiahnite!!!

4) Dotiahnite skrutky blatnka . 5) Pripevnite krytky C a prelepte ich

Manualsnet FAQs

If you want to find out how the ONE BLATNIK Sencor works, you can view and download the Sencor ONE BLATNIK Mudguard User Manual on the Manualsnet website.

Yes, we have the User Manual for Sencor ONE BLATNIK as well as other Sencor manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The User Manual should include all the details that are needed to use a Sencor ONE BLATNIK. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Sencor ONE BLATNIK Mudguard User Manual is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Sencor ONE BLATNIK Mudguard User Manual consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Sencor ONE BLATNIK Mudguard User Manual free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Sencor ONE BLATNIK Mudguard User Manual, simply download the document to your computer. Once downloaded, open the PDF file and print the Sencor ONE BLATNIK Mudguard User Manual as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.