Sealey LED449 Torch Instruction Manual PDF

1 of 2
1 of 2

Summary of Content for Sealey LED449 Torch Instruction Manual PDF

Aluminium Torch 10W crEE XPl lED ADj Focus rEchArgEAblE usb PorT model no: lED449

Thank you for purchasing a sealey product. manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble free performance.

IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.

1. sAFETy 1.1. gEnErAl sAFETy

9 ensure the lamp is fully charged before initial use. 8 Do noT turn the torch on when it is being charged. 8 Do noT shine directly into your, other persons or animals eyes. 8 Do noT allow children to use the torch. 8 Do noT handle or move the torch whilst it is being charged. 8 Do noT use the torch if you suspect that the battery or the torch casing is damaged. 8 Do noT leave battery in a discharged state, recharge battery immediately. Before storage, fully recharge the battery, subsequently

recharge the battery at least once every six months of non-use. 1.2. ElEcTricAl sAFETy

9 Use only the USB charging lead supplied to charge the battery. WArning! It is the users responsibility to read, understand and comply with the following electrical instructions: 9 You must ensure the risk of electric shock is minimised by the installation of appropriate safety devices.

An RCCB (Residual Current Circuit Breaker) should be incorporated in the main distribution board. We also recommend that an RCd (Residual Current device) is used with all electrical products, particularly portable equipment which is plugged into an electrical supply not protected by an RCCB. You must also read and understand the following instructions concerning electrical safety. 1.2.1. The electricity At Work Act 1989 requires all portable electrical appliances, if used on business premises, to be tested by a qualified electrician, using a Portable Appliance Tester (PAT), at least once a year. 1.2.2. The Health & Safety at Work Act 1974 makes owners of electrical appliances responsible for the safe condition of the appliance andthesafetyoftheapplianceoperator.Ifinanydoubtaboutelectricalsafety,contactaqualifiedelectrician. 1.2.3. You must ensure that you:

9 Inspect the cable and connector for wear and damage to ensure items are safe before connecting to the power supply. 8 Do noT use if worn or damaged.

1.3 bATTEry sAFETy WArning!Toreducetheriskofburnsorfire: 8 Do noT Attempt to open, disassemble, modify or service the battery pack. 8 Do noTCrush,puncture,shortexternalcontactsordisposeofinfireorwater. 8 Do noT expose to temperatures above 60C (140). 9 Replace only with the battery pack designated for this product. 9 Recycle or dispose of used battery as stipulated by local regulation. 9 If the electrolyte in the cells gets on your skin, thoroughly wash with soap and water. If it gets in your eyes, rinse thoroughly with cool

water and seek immediate medical attention.

2. inTroDucTion Single 10W CRee XPl led produces extremely bright, white light with an output of 720 lumens and a working range up to 200 metres. Focus type can be changed from spotlight to wide area by a twist action of the head. lightweight aluminium housing. Two power options, full power and 30% energy saving mode. Powered by a rechargeable 3.7V 2Ah li-ion battery. Supplied with micro USB charging lead.

3. sPEciFicATion model no: . . . . . . . . . . . . . . . . . . . . . . . . . . .lED449 Battery: . . . . . . . . . . . . . . . . . . . . . . . 3.7V-2Ah li-ion led: . . . . . . . . . . . . . . . . . . . . . . . . . . 10W T6 CRee lumen output High/low: . . . . . . . . . . . . . 720/210lm operating Time High/low: . . . . . . . . . . . . . . . .2.5/5hr Charging Time: . . . . . . . . . . . . . . . . . . . . . . . . . . .4hr Working Range: . . . . . . . . . . . . . . . . . . . . . . . . .200m nett Weight: . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.34kg

led449 | Issue:5 (1,2) 17/05/2019Original Language Version Jack Sealey limited

Refer to instructions

4. oPErATion 4.1. Beforefirstuse,unscrewthebatterycompartmentscrewcap(fig.1)andremovethewhitediscfrombeneaththecontact. 4.2. UnscrewUSBcovertorevealUSBchargingpoint,wheretheprovidedUSBchargingcablecanbeinserted(fig.2). 4.3. Plug in the cable to an appropriate power source. Charging will take approximately 4hrs. 4.4. WhenchargedremoveUSBcableandscrewclosedtheUSBcover(fig.1). 4.5. Toswitchonpresson/mode/offbutton(baseoftorch),pressagaintochangemode,pressagaintoswitchoff(fig.1). 4.6. Focuscanbeadjustedspotlighttowideanglebytwistingheadoftorch(fig.1).

5. mAinTEnAncE 5.1. Keep the torch clean by wiping with a damp cloth. 5.2. Remove batteries if not being used for a long period of time. 5.3. Store torch and batteries in a dry childproof area.

Original Language Version Jack Sealey limited

sealey group, Kempson Way, suffolk business Park, bury st Edmunds, suffolk. iP32 7Ar 01284 757500 01284 703534 sales@sealey.co.uk www.sealey.co.uk

EnvironmEnT ProTEcTion Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids according to local regulations.

WEEE rEgulATions dispose of this product at the end of its working life in compliance with the eU directive on Waste electrical and electronic equipment (Weee). When the product is no longer required, it must be disposed of in an environmentally protective way. Contact your local solid waste authority for recycling information.

bATTEry rEmovAl Under the Waste Batteries and Accumulators Regulations 2009, Jack Sealey ltd are required to inform potential purchasers of products containing batteries (as defined within these regulations), that they are registered with Valpaks registered compliance scheme. Jack Sealey ltds Batteries Producer Registration number (BPRn) is BPRn00705.

note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice. important: no liability is accepted for incorrect use of this product. Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim.

Parts support is available for this product. Please log on to www.sealey.co.uk, email sales@sealey.co.uk or telephone 01284

Manualsnet FAQs

If you want to find out how the LED449 Sealey works, you can view and download the Sealey LED449 Torch Instruction Manual on the Manualsnet website.

Yes, we have the Instruction Manual for Sealey LED449 as well as other Sealey manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Instruction Manual should include all the details that are needed to use a Sealey LED449. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Sealey LED449 Torch Instruction Manual is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Sealey LED449 Torch Instruction Manual consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Sealey LED449 Torch Instruction Manual free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Sealey LED449 Torch Instruction Manual, simply download the document to your computer. Once downloaded, open the PDF file and print the Sealey LED449 Torch Instruction Manual as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.