Sealey BT2012.V2 Tester Instruction Manual PDF

1 of 3
1 of 3

Summary of Content for Sealey BT2012.V2 Tester Instruction Manual PDF

Digital Battery & alternator tester with Printer 12V Model no: Bt2012.V2

thank you for purchasing a sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble free performance.

IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.

1. safety 1.1. Personal PreCaUtions

9 ensure that there is another person within hearing range and close enough to come to your aid, should a problem arise when working near a lead-acid battery.

9 Wear safety eye protection and protective clothing. Avoid touching eyes while working near battery. 9 Have fresh water nearby in case battery acid contacts skin, clothing, or eyes. 9 Rinse immediately with water if battery acid contacts skin or clothing. If acid enters eye, flush eye immediately with cool, clean

running water for at least 15 minutes and seek immediate medical attention. 9 Remove personal metallic items such as rings, bracelets, necklaces and watches. A lead-acid battery can produce a short-circuit current

which is high enough to weld such items to the vehicle and cause severe burns. 9 ensure that hands, clothing (especially belts) are clear of fan blades and other moving or hot parts of engine. Remove ties and contain

long hair. 8 Do not smoke or allow a spark or flame in the vicinity of the battery or engine.

1.2. general safety instrUCtions 9 Familiarise yourself with the application, limitations and potential hazards of the tester. Also refer to the vehicle manufacturers hand

book. IF In AnY doUBT ConSUlT A QUAlIFIed eleCTRICIAn.

9 ensure that the tester is in good condition before use. If in any doubt Do not use the unit and contact a qualified electrician. 9 only use recommended attachments and parts. To use unapproved items may be dangerous and will invalidate your warranty. 9 Keep tools and other items away from the engine and ensure that you can see the battery and working parts of the engine clearly. 9 determine the system voltage before using the tester. 9 If the tester receives a sharp knock or blow the unit must be checked by a qualified service agent before using. 9 If the battery terminals are corroded or dirty: clean them before using the tester. 9 Keep children and unauthorised persons away from the work area. 8 Do not dismantle the tester for any reason. The tester must only be checked by qualified service personnel. warning! To prevent the risk of sparking, short circuit and possible explosion Do not drop metal tools in the battery area, or allow

them to touch the battery terminals. 8 Do not cross-connect tester to battery. ensure positive (Red) clamp is to positive terminal and negative (BlACK) clamp is to negative

terminal. If battery symbols cannot be distinguished: the negative terminal is the one directly connected to the vehicle bodywork. 8 Do not use the tester outdoors, or in damp, or wet locations and Do not use in the vicinity of flammable liquids or gases. 8 ensure there is effective ventilation to prevent a build-up of explosive gases. 8 Do not use the tester for a task for which it is not designed. 9 When not in use, store the tester carefully in a safe, dry, childproof location.

2. introDUCtion Fast and accurate diagnosis of battery and alternator faults with facility to print the results. large lCd display shows charging and starting system status and returns decision making information in seconds. Results need no interpretation and the tester will work on batteries with as little as 1.5V of residual charge.

3. sPeCifiCation Model no: ............................................................................ Bt2012.V2 Rated Battery Voltage: .....................................................................12V Rating Systems: ....................................................... dIn, en, IeC, SAe Test Range: ..............................................50-1400 Cold Cranking Amps ................................................................................... 50-800 CCA* dIn .................................................................................. 50-1400 CCA* en ................................................................................... 50-800 CCA* IeC ................................................................................ 50-1400 CCA* SAe ................................................................................By Battery Type JIS note: ..........................................................*CCA - Cold Cranking Amps Voltage Range: ..........................................................................1.5-17V Charging System Capability: ............................................................12V

BT2012.V2 Issue 5 (4) 28/02/19Original Language Version Jack Sealey limited

Refer to instructions

Wear eye protection

Warning corrosive substance

Wear protective clothing

Wear protective gloves

Warning

Minimum Power Requirement: ........................................................1.5V nett Weight: ................................................................................1.00Kg Consumable Parts: .............................................................................. Printing Roll for BT2012.V2 Pack of 2 ............................. BT2012.V2-01 Battery: ................................................................. 1 x 9V (not supplied)

4. oPeration warning! ensure that you read, understand and apply the safety and operational instructions before applying the tester clamps to

the battery. only when you are sure that you understand the procedures is it safe to proceed with the testing process. 4.1. PreParation

warning! ensure that the vehicle, or battery, is in a well ventilated area before starting to test. 4.1.1. Check battery casing for cracks or leakage. If damage is found Do not test and replace battery. 4.1.2. Clean battery terminals. 4.1.3. If possible, check electrolyte levels and top-up with distilled water as necessary. 4.1.4. When testing on the vehicle, unless otherwise specified, tests are carried out with all electrical items switched off. leaving any items

on (boot light, interior light, etc.) can result in expensive mis-diagnosis. If the vehicle was running prior to testing, turn on the headlights for 30 seconds to remove surface charge. Switch off the lights, let the battery recover for 60 seconds before testing.

4.1.5. Confirm that the 4 x 1.5V battery (not supplied) is fitted correctly in the compartment in the rear of the tester (fig.1). The batteries power the printer and enables storage of test data after test and disconnection. Do not operate the printer without the print paper loaded and ready for printing.

4.2. ConneCting to Battery 4.2.1. Connect the positive (red) clip to the positive (+) terminal of the battery. ensure a good connection to the terminal. 4.2.2. Connect the negative (black) clip to the negative (-) battery terminal, again ensuring a good connection. 4.3. DisPlay 4.3.1. The initial screen display shows: (fig.3) 4.3.2. Which includes the battery voltage.

4.4. Battery test 4.4.1. Pressing enTeR shows: (fig.4) with TeST BATTeRY flashing. 4.4.2. Press enTeR to select the battery test function. 4.4.3. The display will show input selection view: (fig.5) enter the input standard by means of the doWn or UP key (fig.2) and pressing enter on the appropriate standard. The input standard should be shown on the battery specification label, after the amperage. 4.4.4. When the input standard is selected the amperage screen is displayed: (fig.6) 4.4.5. The required amperage (from the battery label) should be entered using UP or doWn key, pressing the enTeR key to set. 4.4.6. The battery state will be displayed showing: Battery Condition Voltage Resistance Cold Cranking Amps Percentage of Cold Cranking Amps 4.4.7. Press the BACK key (fig.2) to return to the main menu when the test is complete. 4.5. starting systeM test 4.5.1. From the screen shown at 4.4.1., select TeST STARTeR. 4.5.2. Start the vehicle. 4.5.3. The starter test results appear automatically on the display. 4.5.4. Press the BACK key (fig.2) to return to the main menu when the test is complete. 4.6. Charging systeM test 4.6.1. From the screen shown at 4.4.1., select TeST AlTeRnAToR. 4.6.2. The display will show: (fig.7) 4.6.3. Pressing the enTeR key (fig.2) will display the test result. 4.7. other fUnCtions 4.7.1. Scrolling down from 4.4.1. will show: (fig.8)

fig.1 fig.2

fig.4

fig.3

fig.5

fig.6

BT2012.V2 Issue 5 (4) 28/02/19Original Language Version Jack Sealey limited

4.8. View test resUlt 4.8.1. Press VIeW TeST ReSUlT to review the test. Press enTeR to scroll from battery test to starting system to charging system.

4.9. set Date & tiMe 4.9.1. Press SeT dATA & TIMe key. 4.9.2. Press UP or doWn key to add or subtract from the setting. 4.9.3. Press enTeR to scroll right; entering yy-mm-dd. 4.9.4. When complete, press enTeR for 2 seconds to store the set values.

note: There may be a small block of pixels appear on the screen when you are setting the date and time. This is normal for this device and can be corrected by scrolling down through the time or date settings until the mark disappears. This mark does not affect the functionality of the device in any way.

4.10. Printer 8 Do not operate the printer without first loading the paper strip under the print head (fig.9)

4.10.1. To thread the print roll: connect the tester to a vehicle battery, thread the cleanly cut beginning of the roll under the print head until resistance is felt and press the PRInT key (fig.2) to feed through. 4.10.2. At the end of a test procedure, pressing PRInT will print the last set of results. 4.10.3. Alternatively, selecting VIeW TeST ReSUlT (section 4.8.) and then pressing PRInT will print the entire test cycle.

5. troUBleshooting 5.1. In the event of a poor connection, or a battery voltage in excess of 18V, the display will revert to the main menu. 5.2. The printer will not function if the vehicle battery has a charge of less than 10V. 5.3. If the display shows CHeCK PRInT PAPeR, replace printer paper or check the feed. 5.4. If the printer exceeds temperature 75, TeMP oVeR will display. Allow the unit to cool down before continuing.

fig.7

fig.8

fig.9

sealey group, Kempson way, suffolk Business Park, Bury st edmunds, suffolk. iP32 7ar 01284 757500 01284 703534 sales@sealey.co.uk www.sealey.co.uk

enVironMent ProteCtion Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids according to local regulations.

weee regUlations dispose of this product at the end of its working life in compliance with the eU directive on Waste electrical and electronic equipment (Weee). When the product is no longer required, it must be disposed of in an environmentally protective way. Contact your local solid waste authority for recycling information.

Battery reMoVal see seCtion 4.1.5 Under the Waste Batteries and Accumulators Regulations 2009, Jack Sealey ltd are required to inform potential purchasers of products containing batteries (as defined within these regulations), that they are registered with Valpaks registered compliance scheme. Jack Sealey ltd Batteries Producer Registration number (BPRn) is BPRn00705.

note: It is our policy to continually improve products and as such we reserve the right

Manualsnet FAQs

If you want to find out how the BT2012.V2 Sealey works, you can view and download the Sealey BT2012.V2 Tester Instruction Manual on the Manualsnet website.

Yes, we have the Instruction Manual for Sealey BT2012.V2 as well as other Sealey manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Instruction Manual should include all the details that are needed to use a Sealey BT2012.V2. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Sealey BT2012.V2 Tester Instruction Manual is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Sealey BT2012.V2 Tester Instruction Manual consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Sealey BT2012.V2 Tester Instruction Manual free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Sealey BT2012.V2 Tester Instruction Manual, simply download the document to your computer. Once downloaded, open the PDF file and print the Sealey BT2012.V2 Tester Instruction Manual as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.