Sealey SA200T.V2 Tank Instruction Manual PDF

1 of 2
1 of 2

Summary of Content for Sealey SA200T.V2 Tank Instruction Manual PDF

INSTRUCTIONS FOR: COMPRESSER TANK VERTICAL 200ltr MODEL No: SA200T.V2

Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions and properly maintained, give you years of trouble free performance.

1. SAFETY INSTRUCTIONS

IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.

3. CONTENT & ASSEMbLY

2. INTRODUCTION & SPECIFICATION Compressed air receiver tank manufactured to meet 87/404/EEC Pressure Vessel Directive and supplied with test certificate. Includes fitting kit, safety valve, gauge and drain valve (hose not included). Can be used in conjunction with Sealey compressors. Specification: Height: . . . . . . . . . . . . . . . . . . 1554mm Capacity: . . . . . . . . . . . . . . . . . . 200 litre Diameter: . . . . . . . . . . . . . . . . . . 446mm Max. Pressure: . . . . . . . . . . . . . . . 11 bar NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications, and component parts without prior notice.

3.1. Check contents with the list below. If any item is damaged or missing contact your supplier immediately. Receivertank FittingKit,comprising:

3.2. Assembly 3.2.1. Once positioned, the compressor tank should be fixed to the floor utilising the holes provided in the supports. 3.2.2. Using 3/8M -1/4F fitting, fit pressure gauge to port A (if tank is designed with two ports, close the other port with a 3/8M x 1/4F fitting and a1/4M blanking plug). 3.2.3. Fit the 1/4 valve to the lower 1 port b using 1M x 3/4F and 3/4M x 1/4F fittings.This port is the inlet. 3.2.4. Fit a 1/2 valve to the 1 port C, using 1M x 3/4F and 3/4M x 1/2F fittings.This port is the outlet. 3.2.5. Fit a 1/2 valve to the lower 2 port D using 2M-1/2F fitting, to allow drainage of condensation. 3.2.6. Fit the safety valve to port E using 2M x 1/2F and 1/2M x 3/8F fittings. 3.2.7. Connect an air supply hose to inlet port (b) valve and to outlet of supply compressor. If compressor has regulated and unregulated outlets, connect to the unregulated outlet. NOTE: To reduce the risk of leaks, seal all joints with PTFE tape and then bubble test.

1.1. GENERAL SAFETY INSTRUCTIONS 3 Ensure the compressor tank is in a good condition before use. If in any doubt do not use the tank and contact a service agent. 3 Locate the compressor tank in a well ventilated area, away from heat sources, corrosives and inflammable materials. 3 Ensure the compressor tank is placed on a firm, level surface. p WARNING! DO NOT tamper with, or attempt to adjust, the safety valve. 3 Before moving, or working on, the compressor tank,ensure that all tank pressure has been vented. 3 Use only authorised attachments and parts. Unauthorised items may be dangerous and will invalidate the warranty. 3 Ensure the air supply valve is turned off before disconnecting the air supply hose. 3 Ensure air hoses are not tangled, twisted or pinched. 3 Keepchildrenandunauthorisedpersonsawayfromtheworkingarea. 3 Read the instructions relating to any accessory to be used with this compressor tank. Ensure the safe working pressure of any air appliance used exceeds the compressor tanks output pressure. If using a spray gun, check that the area selected for spraying is provided with an air change system/ventilation. 7 DO NOT install the compressor tank outdoors, or in a damp, or wet location. 7 DO NOT use the compressor tank to perform a task for which it is not designed to do. 7 DO NOT deface, or remove, the certification plate attached to the compressor tank. s DANGER! DO NOT direct the compressed air output towards people or animals. p WARNING! The compressor tank is a pressure vessel and the following safety measures apply: 7 DO NOT use the compressor tank without the safety valve fitted. 7 DO NOT tamper with the safety valve, DO NOT modify or alter the compressor tank in any way and DO NOT strap anything to it. 7 DO NOT subject the compressor tank to impact, vibration or heat and DO NOT allow contact with abrasives or corrosives. 3 DO drain condensation from compressor tank daily, and have a detailed inspection carried out annually. The compressor tank shell must not fall below the certified thickness at any point. 3 Keeptoolsandotheritemsawayfromthecompressortankwhenitisinuse,andkeepareacleanandclearofunnecessaryitems. 3 When not in use for a prolonged period, and if possible, store the compressor carefully in a safe, dry, childproof location. p WARNING! The warnings, cautions and instructions referred to in this manual cannot cover all possible conditions and situations that may occur. It must be understood that common sense and caution are factors which cannot be built into this product, but must be applied by the operator.

PressureGauge SafetyValve,11bar Valve,1/2(x2) Valve,1/4

2M-1/2FFitting(x2) 3/8M-1/4FFitting 1M-3/4FFitting(x2)

3/4M-1/2FFitting 3/4M-1/4FFitting 1/2M-3/8FFitting

NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice. IMPORTANT: No liability is accepted for incorrect use of this product. WARRANTY: Guaranteeis12monthsfrompurchasedate,proofofwhichwillberequiredforanyclaim. INFORMATION: For a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode.

01284 757500

Manualsnet FAQs

If you want to find out how the SA200T.V2 Sealey works, you can view and download the Sealey SA200T.V2 Tank Instruction Manual on the Manualsnet website.

Yes, we have the Instruction Manual for Sealey SA200T.V2 as well as other Sealey manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Instruction Manual should include all the details that are needed to use a Sealey SA200T.V2. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Sealey SA200T.V2 Tank Instruction Manual is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Sealey SA200T.V2 Tank Instruction Manual consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Sealey SA200T.V2 Tank Instruction Manual free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Sealey SA200T.V2 Tank Instruction Manual, simply download the document to your computer. Once downloaded, open the PDF file and print the Sealey SA200T.V2 Tank Instruction Manual as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.