Sealey TPS72 Storage Instruction Manual PDF

1 of 4
1 of 4

Summary of Content for Sealey TPS72 Storage Instruction Manual PDF

IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions and maintained properly, give you years of trouble free performance.

Refer to Instruction Manual

1. SAFETY

TPS22,TPS36,TPS72 Issue: 3(SP) - 18/03/17Original Language Version Jack Sealey Limited

INSTRUCTIONS FOR:

MOBILE BIN STORAGE SYSTEMS

MODEL NO'S: TPS22, TPS36, TPS72

WARNING! Ensure Health & Safety, and local authority regulations are adhered to when assembling and using this storage system. Locate storage system in a suitable area where it will not be an obstruction. Keep the general area clean, uncluttered and ensure there is adequate lighting. WARNING! Erect storage system on a level and solid surface such as concrete. Keep children and unauthorised persons away from the storage area. DO NOT use the storage system for any purpose other than that for which it is designed. DO NOT site the storage system out of doors. DO NOT get the storage system wet or use in damp or wet locations or areas where there is condensation. DO NOT clean the shelf supports with any solvents which may damage the coated surface. Ensure that the storage system is properly assembled before loading with heavy items. Load for each shelf must be evenly distributed. Place heavier items on the lower shelves of the storage system. Always push the storage system from the sides, pushing from the front or back creates a tipping hazard.

2. INTRODUCTION Powder coated steel racks with robust composite storage bins evenly spread across multiple shelves. Mounted on heavy-duty castors (two or four lockable, depending on model) for mobility. Unit can hold up to a maximum weight of 60kg - 150kg (Model dependant) evenly spread across the bins. Optional fixing kit available allowing multiple units to be joined together - order Model No. TPSJK.

3. SPECIFICATION Model No: . . . . . . . . . . . . . . . . . . . . . . TPS22. . . . . . . . . . . . . . . . . . . . . . . . . . . TPS36 .........................................................................TPS72 Dimensions (W x D x H): Overall Size: . . . . . . . . . . . . . . . . . . . . . 850 x 385 x 840mm . . . . . . . . . . . . . . . . 855 x 385 X 1710mm ........................1710 x 385 x 1710mm Small Bin: . . . . . . . . . . . . . . . . . . . . . . . 140 x 380 x 90mm (x15) . . . . . . . . . . . . 140 x 380 x 90mm (x15) .................140 x 380 x 90mm (x30) Large Bin: . . . . . . . . . . . . . . . . . . . . . . . 170 x 380 x 180mm (x4) . . . . . . . . . . . . 170 x 380 x 180mm (x12) .............170 x 380 x 180mm (x24) Extra-Large Bin: . . . . . . . . . . . . . . . . . . 245 x 380 x 180mm (x3) . . . . . . . . . . . . 245 x 380 x 180mm (x9) ...............245 x 380 x 180mm (x18) Weight: . . . . . . . . . . . . . . . . . . . . . . . . . 29kg . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39kg ............................................................................... 77kg

4. ASSEMBLY TPS22 & TPS36 4.1. Take the four uprights and insert the four castors into the bottom of each. See fig.1.Ensure the castors are fully seated.

fig.1

4.2 Assembling the front and back frames. 4.2.1. Take two of the uprights with locking castors and insert long beam between the two uprights at the top and bottom (fig.1). Ensure the beams are the correct way up (fig.2A/B) and seated correctly, use a soft faced mallet to tap the beams home. 4.2.2. Repeat process for the other two uprights using the non-locking castors.

fig.2

fig.3

4.3. Attach the front and rear frame together using the smaller side braces with the double tabs, insert at the top and bottom of the frames (fig.3A). Ensure again they are the correct way up and that the locking castors are at the front. 4.4. Between the two uprights Install the centre braces (single tab) half way up the frames. See fig.3B. 4.5. TPS36 ONLY - As well as the side braces attach front and rear beam (single tab) exactly half way up the frame, front and back (fig.3B).

fig.4

4.6. Insert the remaining cross beams in the frame using fig.4 and fig.5 to space them correctly. Ensure the beams are the correct way around to hold the wire shelves (fig.4, fig.5). As before use a soft faced mallet to tap the beams into place.

TPS22,TPS36,TPS72 Issue: 3(SP) - 18/03/17Original Language Version Jack Sealey Limited

4.7. Starting at the bottom place the wire shelves into the frame ensuring the shelves for the larger bins are at the bottom and the shelves for the smaller bins are at the top. Place the flat wire shelf on the top. The storage system is now ready to use.

fig.5

fig.7

fig.8

fig.6 4.8. TPS72 4.8.1. Take four uprights and link using top and bottom couplings (fig.8.B). 4.8.2. Insert the double pin castors into the uprights, ensuring that they seat correctly (fig.8.A). 4.8.3. Fit the remaining castors to the remaining four uprights (fig.1) 4.8.4. Complete assembly as in sections 4.2 to 4.7.

TPS22,TPS36,TPS72 Issue: 3(SP) - 18/03/17Original Language Version Jack Sealey Limited

TPS22 TPS36

TPS72

01284 757500

01284 703534 sales@sealey.co.uk

Sole UK Distributor, Sealey Group, Kempson Way, Suffolk Business Park, Bury St. Edmunds, Suffolk, IP32 7AR

www.sealey.co.uk

NOTE: It is our policy to improve products continually and as such we reserve the right to alter data, specifications and component parts without prior notice. IMPORTANT: No liability is accepted for incorrect use of this product. WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.

Environmental Protection

Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be s

Manualsnet FAQs

If you want to find out how the TPS72 Sealey works, you can view and download the Sealey TPS72 Storage Instruction Manual on the Manualsnet website.

Yes, we have the Instruction Manual for Sealey TPS72 as well as other Sealey manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Instruction Manual should include all the details that are needed to use a Sealey TPS72. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Sealey TPS72 Storage Instruction Manual is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Sealey TPS72 Storage Instruction Manual consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Sealey TPS72 Storage Instruction Manual free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Sealey TPS72 Storage Instruction Manual, simply download the document to your computer. Once downloaded, open the PDF file and print the Sealey TPS72 Storage Instruction Manual as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.