Sealey APMS16HFP Storage Instruction Manual PDF

1 of 9
1 of 9

Summary of Content for Sealey APMS16HFP Storage Instruction Manual PDF

10pc garage storage system model no: apmsHFp serIes

thank you for purchasing a sealey product. manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble free performance.

IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.

1. saFety WarNINg! ensure Health & Safety, local authority, and general workshop practice regulations are adhered to when using this storage

system. 9 locate in a suitable work area. 9 Keep the work area clean, uncluttered and ensure there is adequate lighting. WarNINg! Use storage on level and solid ground, preferably concrete. 9 Keep the storage system clean and tidy in accordance with good workshop practice. 9 Keep children and unauthorised persons away from the work area. 8 Do Not use the storage system for any purpose other than that for which it is designed. 8 Do Not use the storage system outdoors. 8 Do Not place the storage system in a damp or wet location or an area where there is condensation. 8 Do Not clean the storage system with any solvents which may damage the surfaces or the protective coating. 88 8 Do Not move the storage system when there are items placed inside. 88 8 Do Not step on the shelves. 88 8 Do Not8overload the storage system.

2. INtroDuctIoN Can be free standing or fixed to the wall. All ten units supplied on a single pallet. Hinged flat pack design makes this storage system easy and quick to assemble. Base units fitted with stylish black MDF worktops and adjustable feet. Fitted with ball bearing drawer runners and magnetic door latches. Pegboard design backing panels for additional storage. Extra units available to extend the storage system if required. Some simple assembly required.

3. specIFIcatIoN model no: .........................................................apms10HFp Garage storage system 10pc overall size: ........................................3100 x 460 x 2080mm Inner drawer dimensions: ........................670 x 398 x 122mm model no: ...........................................................apms2HFp modular wall and base cabinet model no: ........................................................ apms2HFpD modular wall and base cabinet with drawer model no: ........................................................ apms2HFps modular stacking cabinet

APMSHFP series | Issue 1 21/10/19Original Language Version Jack Sealey limited

Refer to instruction

manual

Wear protective

gloves

4. assembly

Original Language Version Jack Sealey limited

1 Door Wall cabINet step 1: Carefully separate the front and back panels, allowing the side panels to unfold completely.

step 2: attach the top panel using 8x M6x16mm screws. step 3: Turn the cabinet over. Attach the bottom panel using 11x M6x16mm screws.

step 4: Insert 4 shelf supports inside the cabinet at the desired height. Place the shelf on the shelf supports.

APMSHFP series | Issue 1 21/10/19

top panel

shelf support x4

shelf

Original Language Version Jack Sealey limited

step 2: Attach the bottom panel using 11x M6x16mm screws.

step 3: Screw the 4 adjustable feet into the cabinet bottom.

step 4: Attach the worktop to the cabinet using 4x M6x16mm screws.

step 5: Insert four shelf supports inside the cabinet at the desired height. Place the shelf on the shelf supports. Note: The cabinet will only lock when the shelf is placed in the centre position.

APMSHFP series | Issue 1 21/10/19

2 Door base cabINet WItH Work top step 1: Carefully separate the front and back panels, allowing the side panels to unfold completely.

m6x16mm screws x4

shelf support x4

Original Language Version Jack Sealey limited

step 2 top cabINet: Attach the top panel using 8x M6x16mm hex socket head screws.

step 4 top cabINet: Turn the cabinet over. Attach the bottom panel using 7x M6x16mm screws.

2 Door stackINg cabINet step 1: Carefully separate the front and back panels, allowing the side panels to unfold completely.

step 3 bottom cabINet: Place the top panel on the bottom cabinet. do not attach yet.

APMSHFP series | Issue 1 21/10/19

m6x16mm screws x8

m6x16mm screws x7

top panel

top cabinet

top cabinet

top cabinet

bottom cabinet

top panel

step 5 bottom cabINet: Turn the cabinet over. Attach the bottom panel using 11x M6x16mm screws.

step 6 bottom cabINet: Fit adjustable feet.

step 7: Place top cabinet onto bottom cabinet.

step 9: Insert 4x shelf supports inside the cabinet at the desired height. Place shelf on shelf supports. Note: the cabinet will only lock when the shelf is placed in the centre position.

step 8: Connect top and bottom cabinets using M6x35mm hex flange bolts.

repeat for the other stackable combination.

m6x35 flange bolt x4

Original Language Version Jack Sealey limited APMSHFP series | Issue 1 21/10/19

bottom cabinet

bottom cabinet

bottom cabinet

top cabinet

m6x16mm screws

shelf

shelf support

1 DraWer/2 Door cabINet WItH Work top: raIl types:

step 1: Fit feet.

step 2: Attach 2x cabinet rails to the back of the base cabinet using 3x M6x16mm screws per rail.

step 3: Slide 2x peg board rails fully onto the cabinet posts. Place one pegboard on the front, making sure the grommet hole is on the bottom. Attach using 2x M6x16mm screws per rail.

to remoVe DraWers Pull drawer out so its almost fully extended. Push up right hand black release lever, while pulling down left hand black release lever, pull the drawer out until it is released from the slides.

to replace DraWers extend the drawer slides. Insert the brackets on each side of the drawer into the slots in the cabinet slides, being careful to ensure that they are properly positioned. once properly inserted, completely close The drawer to set the slides in their proper positions.

APMSHFP series | Issue 1 21/10/19Original Language Version Jack Sealey limited

cabinet rail x8

adjustable feet

pegboard x1

pegboard rail x2

m6x16mm screw x4

pegboard rail x4

pegboard x4

step 4: Slide 2 cabinet rails onto the pegboard rails. Ensure there is enough room at the top for the wall cabinet. Attach 2 cabinet rails using 2x M6x16mm screws per rail. Attach second pegboard, ensure grommet hole is at the top.

2 Door cabINet WItH Worktop:

step 7: Slide 2 pegboard rails fully onto the cabinet rails. Place one pegboard on the front, making sure the grommet hole is on the bottom. Attach using 2x M6x16 screws per rail.

step 5: Screw two M6x16mm screws, into the back of the top cabinet, leaving a 0.8cm gap. do not tighten bolts fully. Hang the wall cabinet on the top of the posts, then fully tighten the screws. Attach the bottom of the wall cabinet to the posts using another 2x M6x16mm screws.

step 8: Slide 2 cabinet rails onto the pegboard rails. make sure to leave enough room at the top for the wall cabinet. Place one pegboard on the front, making sure the grommet hole is on the top. Attach using 2x M6x16mm screws per rail.

step 9: Screw 2x M6 x 16mm into the back of the top cabinet, leaving a 0.8cm. Do not tighten bolts fully. Hang the wall cabinet on the top of the rails, then fully tighten the screws. Attach the bottom of the wall cabinet to the rails using another two M6x 16mm screws.

APMSHFP series | Issue 1 21/10/19Original Language Version Jack Sealey limited

pegboard

cabinet rail

m6x16mm screw x4

m6x16mm screw x6 m6x16mm

screw x4

m6x16mm screw x4

m6x16mm screw x2

pegboard rail x2

cabinet rail x2

pegboard x1

m6x16mm screw x2

step 6: Attach 2x cabinet rails to the back of the base cabinet using 3x M6x16mm screws per rail.

step 10: Push the two base cabinet/top cabinet combinations together. Insert a M6x16mm screw through the two interior end cover holes and fasten with a M6 flange nut.

step 11: Push a stackable cabinet combination towards either side of the base cabinet/top cabinet combination. Insert a M6x16mm screw through the two interior end cover holes and secure with a M6 flange nut.

APMSHFP series | Issue 1 21/10/19Original Language Version Jack Sealey limited

m6x16mm screw x2

m6x16mm screw x2

m6 flange nut

step 12: Attach the modular storage kit to the wall using twelve M6x65mm tapping screws and washers insert through wall studs. Insert the 6 end cups on the side panels of the cabinets.

sealey group, kempson Way, suffolk business park, bury st edmunds, suffolk. Ip32 7ar 01284 757500 01284 703534 sales@sealey.co.uk www.sealey.co.uk

Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice. Important: no liability is accepted for incorrect use of this product. Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim.

eNVIroNmeNt protectIoN Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids according to local regulations.

APMSHFP series | Issue 1 21/10/19Original Language Version Jack Sealey limited

washer x12

m6x65mm self tapping screw

end cap

wall

Manualsnet FAQs

If you want to find out how the APMS16HFP Sealey works, you can view and download the Sealey APMS16HFP Storage Instruction Manual on the Manualsnet website.

Yes, we have the Instruction Manual for Sealey APMS16HFP as well as other Sealey manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Instruction Manual should include all the details that are needed to use a Sealey APMS16HFP. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Sealey APMS16HFP Storage Instruction Manual is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Sealey APMS16HFP Storage Instruction Manual consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Sealey APMS16HFP Storage Instruction Manual free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Sealey APMS16HFP Storage Instruction Manual, simply download the document to your computer. Once downloaded, open the PDF file and print the Sealey APMS16HFP Storage Instruction Manual as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.