Sealey HVLP736 Spray Gun Instruction Manual PDF

1 of 3
1 of 3

Summary of Content for Sealey HVLP736 Spray Gun Instruction Manual PDF

HVLP GRAVITY FEED TOUCH UP SPRAY GUN 0.8mm SET UP MODEL NO: HVLP736

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble free performance.

IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.

1. SAFETY

9 Familiarise yourself with the application, limitations and potential hazards peculiar to the spray gun. WARNING! Disconnect the spray gun from the air supply before changing accessories, servicing or performing any maintenance. 9 Maintain thespray gun in good condition (use an authorised service agent). 9 Replace or repair damaged parts. Use recommended parts only. Unauthorised parts may be dangerous and will invalidate the warranty. 9 Keep the spray gun clean for best and safest performance. 9 Ensure that the compressed air system can supply the spray gun air consumption (9cfm). 9 Wear approved safety respiratory protection and safety eye goggles. 9 If spraying isocynate based finisher, wear approved respirator/clean air breathing apparatus and cover exposed skin with latex gloves and

an impervious hooded coverall. 9 Remove ill-fitting clothing. Remove ties, watches, rings and other loose jewellery and tie back long hair. 9 Locate the spray gun in a suitable work area. Keep area clean and tidy and free from unrelated materials and ensure that there is adequate

ventilation and lighting. 9 Keep children and unauthorised persons away from the work area. 9 When not in use, ensure that the air supply is turned off. 9 Avoid unintentional operation of spray gun. 8 DO NOT point spray gun at yourself, other persons or animals. 8 DO NOT direct air from the air hose at yourself, other persons or animals. 8 DO NOT carry the spray gun by the hose, or yank the hose from the air supply. 8 DO NOT exceed the maximum air pressure of 29psi. 8 DO NOT use the spray gun for any purpose other than that for which it is designed. 8 DO NOT allow untrained persons to operate the spray gun. 8 DO NOT get the spray gun wet or use in damp or wet locations or in areas where there is condensation. 8 DO NOT operate the spray gun if any parts are missing or damaged as this may cause failure and/or personal injury. 9 When not in use, disconnect the spray gun from the air supply, clean thoroughly and store safely.

2. INTRODUCTION Professional gravity feed touch-up spray gun with 0.8mm set-up, ideal for small panels. Brass air cap with stainless steel needle and nozzle suitable for water based paints. Features air and paint flow controls for fine adjustment of spray pattern. Fully polished body resists corrosion and makes for easy cleaning. Alternative set-up available separately.

3. SPECIFICATION Model No: .......................................... HLVP736 Gravity Feed Standard set-up: .............................................................0.8mm Available set-ups: ...........................................................1.0mm Air pressure: .....................................................................29psi Air consumption: ................................................................9cfm Pot Capacity: ...................................................................125ml

4. AIR SUPPLY CONNECTION 4.1. Air Supply

WARNING! Ensure the air supply is clean and does not exceed 29psi while operating the spray gun. Too high an air pressure and/or unclean air will shorten the product life due to excessive wear, and may be dangerous causing damage and/or personal injury.

4.1.1. Ensure spray gun air valve (or trigger) is in the off position before connecting to the air supply. 4.1.2. You will require an air pressure of 29psi, and an air flow according to specification. 4.1.3. Drain the air tank daily. Water in the air line will ruin the paint finish and damage the spray gun. 4.1.4. Clean air inlet filter weekly. 4.1.5. Line pressure should be increased to compensate for unusually long air hoses (over 8 metres). The minimum hose diameter should be

1/4 internal diameter and fittings must have compatible dimensions. 4.1.6. Keep hose away from heat, oil and sharp edges. Check hose for wear, and make certain that all connections are secure. 4.2. Couplings 4.3. Vibration may cause failure if a quick change coupling is connected directly to the spray gun. To overcome this, connect a leader hose

to the spray gun (Sealey ref: AH2R or AH2R/38). A quick change coupling may then be used to connect the leader hose to the air line recoil hose. See fig.1 & fig.2.

HVLP736 Issue 2 (3,H,F) 01/10/21Original Language Version Jack Sealey Limited

Refer to instructions

Wear eye protection

Wear respiratory protection

Wear protective clothing

5. OPERATION 5.1. For best results, the gun should be held perpendicular to the surface being sprayed and moved parallel to it. Start the stroke before

squeezing the trigger and release the trigger before finishing the stroke. This will enable you to accurately control the gun and material (fig.3). 5.2. Spray from a distance of about 150mm to 250mm depending on the material and the atomizing pressure. The material deposited should

always be even and wet. Each stroke must overlap the preceding stroke to obtain a uniform finish. To reduce over-spray and obtain maximum efficiency, spray with the lowest possible atomising air pressure.

5.3. Controlling the fan spray and the fluid. a) Use the needle (paint) adjustment knob (fig.4.2) to increase or decrease the amount of paint flow. b) The atomizing air flow is controlled by knob (4.1). The volume of air input is controlled by knob (4.3). c) As width of spray is increased more material must pass through the gun to obtain the same coverage on the increased area. d) Turn the air nozzle (4.4) to achieve a horizontal or vertical fan spray. Lock the nozzle with retaining ring (4.5).

The spray pattern of the gun is variable from round to flat with all patterns in between. In normal operation, the wings on the nozzle are horizontal. See fig.5. This provides a vertical fan-shaped pattern which gives maximum uniform and even coverage when moving the gun back and forth, parallel to the work surface.

HVLP736 Issue 2 (3,H,F) 01/10/21Original Language Version Jack Sealey Limited

6. CLEANING & MAINTENANCE FOR OPTIMUM PERFORMANCE IT IS VERY IMPORTANT TO ENSURE THE GUN IS CORRECTLY CLEANED AFTER EACH USE Disconnect from the air supply before attempting any cleaning or maintenance.

6.1. Cleaning the gun 6.1.1. Immerse the front end of the gun only in solvent. The solvent should just cover the

fluid connection. (fig.6). 6.1.2. Use the bristle brush (fig.7) and solvent to wash off accumulated paint. 6.1.3. Do not immerse the entire gun in solvent as this will cause lubricants on the

rubber seals to dissolve. Dirty solvent may also clog narrow passages in the gun. 6.1.4. Flush the gun through with clean solvent. 6.1.5. Wipe the outside of the gun with a dampened solvent rag.

fig.1 fig.2

fig.3

fig.4

fig.5

fig.6

Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR 01284 757500 01284 703534 sales@sealey.co.uk www.sealey.co.uk

ENVIRONMENT PROTECTION Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids according to local regulations.

Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice. Important: No Liability is accepted for incorrect use of this product. Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim.

HVLP736 Issue 2 (3,H,F) 01/10/21Original Language Version Jack Sealey Limited

VIEW OF PROBLEM POSSIBLE REASON FOR PROBLEM SOLUTION

Dried material in a dirty side port restricts passage of air. Greater flow of air from the cleaner side port forces a fan pattern in the direction of the clogged side.

Dissolve material in the side ports with solvent, then blow the gun clean. Do not poke into the opening with metal instruments.

Dried material around the outside of the fluid nozzle tip restricts the passage of atomising air at one point through the centre opening of the air nozzle and results in the pattern shown. This pattern can also be caused by a loose air nozzle.

Remove the air nozzle and wipe off fluid tip using a rag dampened with solvent. Tighten the air nozzle.

Material too thin or atomization air pressure too high. Regulate material viscosity or reduce air pressure.

Dirt between the fluid nozzle seat and body or loosely installed fluid nozzle will cause the gun to spit.

Remove the fluid nozzle, clean the back of the nozzle and the nozzle seat in the gun body using a rag dampened with thinner. Replace the nozzle and secure it tightly against the body.

Atomised air flowing through the paint channel to pot. The paint nozzle is not tight enough. Air nozzle is not completely screwed in.

Tighten, clean or replace parts accordingly. Material bubbles or 'boils' in paint cup.

6.2. Air nozzle, fluid nozzle and needle assembly 6.2.1. To clean the nozzles, soak them in solvent to

dissolve any dried material then blow them clean with air. Handle all nozzles carefully and do not make any alterations in the gun.

6.2.2. If you need to probe the holes in the nozzles, be sure to use a tool that is softer than brass; do not use metal instruments.

6.2.3. Adjust the fluid needle valve so that when the gun is triggered, air flow occurs before fluid flow.

6.3. Maintenance 6.3.1. Disassemble using the supplied spanner. (fig.7) 6.3.2. Take care when re-assembling. Firstly screw

parts hand tight to avoid cross-threading then tighten with spanner. If a part cannot easily be turned by hand, check that you have the correct part, or unscrew, realign and try again. DO NOT use excessive force when re-assembling.

6.3.3. Lubricate the gun daily with a light machine oil. 6.3.4. If you change the nozzle size, ensure the

complete nozzle set is exchanged. Insert paint nozzle before putting the paint needle in.

7. TROUBLE SHOOTING.

A faulty spray is usually caused by improper cleaning or dried material around the fluid nozzle tip or in the air nozzle. Soak these parts in a solvent that will soften the dried material and remove with a brush or a cloth. Never use metal instruments to clean the air or fluid nozzles. These parts are carefully machined and any damage will cause a faulty spray. If either the air nozzle or fluid nozzle is damaged, these parts must be replaced before a perfect spray can

Manualsnet FAQs

If you want to find out how the HVLP736 Sealey works, you can view and download the Sealey HVLP736 Spray Gun Instruction Manual on the Manualsnet website.

Yes, we have the Instruction Manual for Sealey HVLP736 as well as other Sealey manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Instruction Manual should include all the details that are needed to use a Sealey HVLP736. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Sealey HVLP736 Spray Gun Instruction Manual is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Sealey HVLP736 Spray Gun Instruction Manual consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Sealey HVLP736 Spray Gun Instruction Manual free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Sealey HVLP736 Spray Gun Instruction Manual, simply download the document to your computer. Once downloaded, open the PDF file and print the Sealey HVLP736 Spray Gun Instruction Manual as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.