48W SOLDERING STATION MODEL NO: SD008
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY 1.1. ELECTRICAL SAFETY
WARNING! It is the responsibility of the owner and the operator to read, understand and comply with the following: You must check all electrical products, before use, to ensure that they are safe. You must inspect power cables, plugs, sockets and any other connectors for wear or damage. You must ensure that the risk of electric shock is minimised by the installation of appropriate safety devices. A Residual Current Circuit Breaker (RCCB) should be incorporated in the main distribution board. You must also read and understand the following instructions concerning electrical safety.
9 Ensure that cables are always protected against short circuit and overload. 9 Regularly inspect power supply cables and plugs for wear or damage and check all connections
to ensure that none are loose. 9 Ensure that the voltage marked on the appliance matches the power supply to be
usedandthattheplugisfittedwiththecorrectfuse-seefuseratingatright. 8 DO NOT use worn or damaged cables, plugs or connectors. Have any faulty item repaired or
replaced immediately by a competent electrician. 9 It is recommended that this device is wired directly to a fused isolator switch. If, however, a plug
isfitted,thefollowingapplies: 9 Fit a new plug according to the following instructions (UK only).
a) Connect the GREEN/YELLOW earth wire to the earth terminal E. b) Connect the BROWN live wire to the live terminal L. c) Connect the BLUE neutral wire to the neutral terminal N. d) After wiring, check that there are no bare wires, that all wires have been correctly connected, that the cable restraint is tight. 1.2. GENERAL SAFETY
WARNING! Ensure Health & Safety, local authority, and general workshop practice regulations are adhered to when using this equipment.
9 Familiarise yourself with the application, limitations and potential hazards of the soldering station. 9 Replace or repair damaged parts. Use genuine parts only. Unauthorised parts may be dangerous and will invalidate the warranty. 9 Locate soldering station in a suitable working area, keep area clean and tidy and free from unrelated materials. 9 Keep the work area clean, uncluttered and ensure there is adequate lighting. 9 Keep the soldering iron clean for best and safest performance. 9 Ensuretherearenoflammableorcombustiblematerialsneartheworkarea. 9 Wear approved safety eye protection (standard spectacles are not adequate). 9 Wear appropriate protective clothing. 9 Ensure the workpiece is adequately held before operating the soldering iron. 9 Always replace the soldering iron in its holder when not in use. 9 Remove excess solder from the soldering iron by wiping the tip on a damp, natural sponge; not by abrupt force. 8 DO NOT attempt to remove excess solder from the soldering iron by shaking it. Hot solder may become airborne and land on skin
causing burns and blisters. 8 DO NOT allow children or pets into the area where the soldering is taking place. 8 DO NOT attempt to cool the soldering iron with water.
NOTE: This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.
2. INTRODUCTION 48WSolderingstationwithrapidheatup.Variabletemperaturecontrol.Maintainstemperaturesbetween160-480C.Suppliedwithametal soldering iron stand, tip sponge, replaceable tip.
Recommended fuse rating 3 Amp
SD008 Issue 1 28/01/2021Original Language Version Jack Sealey Limited
Refer to instructions
Indoor use only Hot surfaces