Sealey PPFSG3 Safety Guard Instruction Manual PDF

1 of 2
1 of 2

Summary of Content for Sealey PPFSG3 Safety Guard Instruction Manual PDF

SAFETY GUARD FOR PPF501S, PPF100S PRESSES MODEL NO: PPFSG3, PPFSG4

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble free performance.

IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.

1. SAFETY Familiarise yourself with the applications, limitations and hazards peculiar to the safety guard. Maintain the safety guard in good condition. Replace or repair damaged parts. Use recommended parts only. Unauthorised parts may be dangerous and will invalidate the

warranty. Keep the safety guard clean for best and safest performance. Ensure the safety guard is correctly attached before operating the press. Ensure that all fittings are tight before each use. Remove ill fitting clothing. Remove ties, watches, rings, loose jewellery and contain long hair. Keep hands and body clear of the safety guard when operating the press. Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip footware. Keep children and unauthorised persons away from the working area. DO NOT use the guard for purposes other than those it was designed for. WARNING! Always, refer to the safety instructions provided in your presses instruction manual. WARNING! The warnings, cautions and instructions in this manual cannot cover all possible conditions and situations that may

occur. It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be applied by the operator.

2. INTRODUCTION Lightweight steel frame with tough 4.8mm Polycarbonate screen. Adjustable guard protects the user and/or passer by from being injured if workpiece is accidentally dislodged under load. Bolts onto either side of the table and features six height increments, allowing the workpiece to be placed onto table with no obstruction. One-way spring loaded locking clips then allow the guard to be pulled up quickly and snap straight into position for full protection.

3. SPECIFICATION Model No: .....................................................................................PPFSG3 ................................................................ PPFSG4 Application(s): ................................................................................PPF501 ............................................................... PPF100S

4. ASSEMBLY Unpack the product and check contents. Should there be any damaged or missing parts contact your supplier immediately.

Refer to attached parts list. 4.1. ATTACH HANDLE GRIP 4.1.1. Remove protective lm from PC board (#1). 4.1.2. Position handle grip (#5) onto PC board (#1) and secure with at washer M5 (#3) and machine screw pan head M5 x 10 (#2). 4.2. ATTACH LOCKING KNOB 4.2.1. Screw locking knob (#18) into threaded insert located at the top, left hand side of the frame (#8).

5. OPERATION 5.1. ATTACH THE SAFETY GUARD 5.1.1. Lift up the safety guard by taking hold of the side grips (#10). NOTE: Handle grip (#5) to be facing outwards and at its lowest position (fig 2). 5.1.2. Insert the T-shape screws (#9) into the key holes located on the front of the press working table ( gs 1 & 3). WARNING! Ensure that both the T-shape screws are fully located into the key slots. Failure to do so may result in the safety guard

becoming detached from the press causing possible personal injury and damage to the safety guard. 5.2. INSERTING THE WORKPIECE 5.2.1. Holding the handle grip (#5) turn the locking knob (#18) counter clockwise ( g 2) and raise the safety guard PC board (#1) fully to

the top ( g 2). 5.2.2. Lock the PC board (#1) into place by turning the locking knob (#18) clockwise ( g 2). DO NOT over tighten. 5.2.3. Insert the workpiece onto the press working table.

PPFSG3, PPFSG4 Issue 1 23/03/22Original Language Version Jack Sealey Limited

Refer to instructions

5.2.4. Holding the handle grip (#5) unlock the locking knob (#18) by turning counter clockwise ( g 2) and lower the PC board (#1) fully down.

5.2.5. Lock the PC board (#1) into place by turning the locking knob (#18) clockwise ( g 2). DO NOT over tighten. 5.2.6. When the press operation is complete raise the PC board (#1). See section 5.2.1. 5.2.7. Remove the workpiece. 5.2.8. Lower the PC board (#1). See section 5.2.4. 5.2.9. Lock the PC board (#1) See section 5.2.5. 5.3. REMOVING THE SAFETY GUARD 5.4. NOTE: Ensure that the PC board (#1) is locked in place and is at its lowest position. 5.4.1. Remove the safety guard by taking hold of the side grips (#10) and raise slightly. 5.4.2. Align the T shaped screws (#9) with the larger hole of the key slot and pull the safety guard away and place in a secure location.

6. MAINTENANCE 6.1. Clean with a damp cloth.

DO NOT use solvents.

PPFSG3, PPFSG4 Issue 1 23/03/22Original Language Version Jack Sealey Limited

g.1 g.2 g.3

Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR 01284 757500 01284 703534 sales@sealey.co.uk www.sealey.co.uk

Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice. Important: No Liability is accepted for incorrect use of this product. Warranty: Guarantee is 24 months from purchase date, proof of which is required for any claim.

ENVIRONMENT PROTECTION Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should

Manualsnet FAQs

If you want to find out how the PPFSG3 Sealey works, you can view and download the Sealey PPFSG3 Safety Guard Instruction Manual on the Manualsnet website.

Yes, we have the Instruction Manual for Sealey PPFSG3 as well as other Sealey manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Instruction Manual should include all the details that are needed to use a Sealey PPFSG3. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Sealey PPFSG3 Safety Guard Instruction Manual is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Sealey PPFSG3 Safety Guard Instruction Manual consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Sealey PPFSG3 Safety Guard Instruction Manual free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Sealey PPFSG3 Safety Guard Instruction Manual, simply download the document to your computer. Once downloaded, open the PDF file and print the Sealey PPFSG3 Safety Guard Instruction Manual as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.