Sealey SECS06 Safe Instruction Manual PDF

1 of 3
1 of 3

Summary of Content for Sealey SECS06 Safe Instruction Manual PDF

instructions for

electronic combination security safes

thank you for purchasing a sealey product. manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble free performance.

IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.

1. safety WarninG! these safes are heavy and care should be exercised in transit and handling to ensure that no one is injured. WarninG! the installation of the safe should be carried out by 2 people. 9 for maximum security, these safes must be securely fixed to a floor or wall. 9 Ensure that any safe secured to a wall, is on a firm level surface. 8 Do not install in areas where damp and condensation are present. WarninG! the warnings, cautions and instructions referred to in this instruction manual cannot cover all possible conditions and

situations that may occur. it must be understood that common sense and caution are factors which cannot be built into this product, but must be applied by the operator.

2. i introDuction Heavy-duty construction with twin locking bolts. simple to operate electronic keypad accepts numbers of between three and eight digits, giving millions of combinations. Model sEcs01Ds also features safety deposit slot. three LEDs show security, power and operating status. Also supplied with two keys for manual override should batteries fail. includes screws and wall plugs.

WarninG! if you or an intruder uses an incorrect group of numbers, the cabinet will not open and a yellow light will illuminate. Entering an incorrect Pin 3 times will freeze the system for 20 seconds.

Keep the cabinet key and any record of the code separate from the cabinet and unidentified.

3. ispecification

4. installation 4.1. consideration should be given to the placing of the safe to ensure that it is placed in a discreet location and will not be easily found by

intruders. 4.2. Each safe is supplied with anchor bolts suitable for fixing to brick and concrete. 4.3. fixing to hollow partition walls is not recommended. if fixed to wood it must be to a solid wooden structure. 4.4. open the door of the safe (see 5.1 for opening instructions) and with the help of a second person, position it where required and mark

the mounting positions through the pre-drilled holes in the back or base of the safe. 4.5. When mounting to a wall, ensure that the safe is sitting on a firm level surface. 4.6. Drill 10mm holes to a depth of 38mm (fig.1.1) and insert the anchor bolts with nuts and washers removed (fig.1.2). 4.7. Position the safe over the four protruding mounting studs and support it there whilst placing a washer, split washer and nut onto each stud

(fig.1.3). 4.8. continue to support the safe whilst tightening the fixings using a 10mm spanner. (fig.1.4)

Original Language Version Jack sealey Limited

refer to instruction

manual

Model nos: secs00 secs01 secs01Ds secs02 secs03 secs04 secs05 secs06

Wear Protective footwear

Model number External size (W x D x H)

internal size (W x D x H)

Wall / Door thickness

shelves slot size (W x H)

sEcs00 310 x 200 x 200mm 305 x 180 x 195mm 2 / 4 n/a n/a

sEcs01 350 x 250 x 250mm 345 x 230 x 245mm 2 / 4 n/a n/a

sEcs01Ds 350 x 250 x 250mm 345 x 230 x 245mm 2 / 4 n/a 145 x 10mm

sEcs02 380 x 300 x 300mm 375 x 280 x 295mm 2 / 4 1 n/a

sEcs03 450 x 365 x 250mm 445 x 350 x 245mm 2 / 4 n/a n/a

sEcs04 350 x 330 x 500mm 346 x 312 x 496mm 2 / 4 2 n/a

sEcs05 380 x 360 x 575mm 376 x 330 x 572mm 2 / 4 2 n/a

sEcs06 515 x 480 x 890mm 510 x 470 x 880mm 2 / 4 2 n/a

sEcs00,sEcs01,sEcs01Ds,sEcs02 sEcs03, sEcs04, sEcs05, sEcs06 | issue: 5 (H, 3, f) 10/11/17

5. operation 5.1. initial opening. 5.1.1. to open the door of the safe for the first time remove the logo panel in the centre of the main control panel. Prise out the panel using a

small screwdriver. insert key and turn anti-clockwise and the safe will be unlocked. 5.2. entering a new combination. 5.2.1. the combination must consist of between 3 and 8 numbers and should be safely recorded before being entered into the safe

electronics. 5.2.2. firstly remove the battery cover from the rear of the safe door and insert 4 x AA batteries. replace battery cover. 5.2.3. Press the red button on the inside of the door near the hinges. 5.2.4. now enter your personal combination (3-8 numbers), and then press the # key to confirm your combination. A beep will sound for each

key pressed. Be sure to write down this combination immediately, so you do not forget. note! after entering the correct combination, if you do not open the door within 5 seconds it will re-lock. note! if the incorrect combination is used 3 times the system will freeze for 20 seconds. if again the incorrect combination is used 3 times the system will freeze for 5 minutes. 5.3. Key operation. 5.3.1. if you forget your combination, you can use the manual override key: Do not keep override key in safe. the override lock is situated

under the logo panel in the centre of the main control panel. Prise out the panel using a small screwdriver. insert key and turn anti- clockwise and the safe will be unlocked. snap panel back into place afterwards.

5.3.2. Please make a note of the key number which can be found on the key or on the barrel in the safe. 5.4. low battery warning and replacement. 5.4.1. if red light shows in the top middle of the control panel this indicates low batteries. change batteries by opening the safe and removing

them from the back of the door. then replace all batteries with new ones. 5.4.2. if the keypad does not work because the batteries in the safe are exhausted, use the override key to open the safe, and then replace

all batteries. 5.5. audible beep shut off. 5.5.1. the Audible Beep heard when pressing any button on the keypad can be turned on and off using the codes below. 5.5.2. Enter *633 to turn the sound off. 5.5.3. Enter *66 to turn the sound on. 5.6. lost keys. 5.6.1. should you lose your keys, we can supply replacements. to order these please contact our sales office on 01284 757500 and quote the

unique number on the safe lock. We will also require a copy of your purchase invoice for the safe to confirm that you are the owner. 5.6.2. Please note that replacement keys are special order only (we do not carry these in stock for security reasons) and as such they can take 14 28 days to arrive.

Original Language Version Jack sealey Limited sEcs00,sEcs01,sEcs01Ds,sEcs02 sEcs03, sEcs04, sEcs05, sEcs06 | issue: 5 (H, 3, f) 10/11/17

sealey Group, Kempson Way, suffolk business park, bury st edmunds, suffolk. ip32 7ar 01284 757500 01284 703534 sales@sealey.co.uk www.sealey.co.uk

note: it is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice. important: no Liability is accepted for incorrect use of this product. Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim.

battery removal see 5.4 under the Waste Batteries and Accumulators regulations 2009, Jack sealey Ltd are required to inform potential purchasers of products containing batteries (as defined within these regulations), that they are registered with Valpaks registered compliance scheme. Jack sealey Ltd Batteries Producer registration number (BPrn) is BPrn00705.

environment protection recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids according to local regulations.

fig.1

sEcs00,sEcs01,sEcs01Ds,sEcs02 sEcs03, sEcs04, sEcs05, sEcs06 | issue: 5 (H,

Manualsnet FAQs

If you want to find out how the SECS06 Sealey works, you can view and download the Sealey SECS06 Safe Instruction Manual on the Manualsnet website.

Yes, we have the Instruction Manual for Sealey SECS06 as well as other Sealey manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Instruction Manual should include all the details that are needed to use a Sealey SECS06. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Sealey SECS06 Safe Instruction Manual is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Sealey SECS06 Safe Instruction Manual consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Sealey SECS06 Safe Instruction Manual free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Sealey SECS06 Safe Instruction Manual, simply download the document to your computer. Once downloaded, open the PDF file and print the Sealey SECS06 Safe Instruction Manual as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.