Sealey SMC3 Press Instruction Manual PDF

1 of 2
1 of 2

Summary of Content for Sealey SMC3 Press Instruction Manual PDF

MOTORCYCLE STEERING BEARING PRESS

MODEL NO: SMC3

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble free performance.

IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.

1. SAFETY WARNING! Ensure Health & Safety, local authority, and general workshop practice regulations are adhered to when using this

equipment. WARNING! Always wear approved eye protection when using the press. Failure to do so may result in serious injury. Normal spectacles

are not adequate protection. 9 Familiarise yourself with the specific applications and limitations of the press, as well as any potential hazards. 9 If unsure of the applications or limitations of the press, contact your supplier. 9 Ensure that the press is the correct tool for the task. DO NOT use the press for any purpose other than that for which it is designed. 9 Replace or repair damaged parts. Use genuine parts only. Unauthorised parts may be dangerous and will invalidate the warranty. 9 Ensure that the workpiece is stable and that there is adequate lighting. 9 Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes. 9 Ensure that the front of the motorcycle frame is adequately supported when the front wheel and forks are removed. 8 DO NOT use press if any parts are damaged or missing as this may cause failure and/or personal injury. 8 DO NOT use the press when you are tired or under the influence of alcohol, drugs or intoxicating medication. 9 Keep children and unauthorised persons away from the working area. 9 When not in use, return parts to the case, and store in a safe, dry, childproof location.

2. INTRODUCTION Aluminium kit suitable for straight installation of bearing race without damage to the bearings or headstock. Includes seven dies for bearing sizes ranging from 32 to 46mm. Bearing setting bar features seven increments for a wide range of headstock sizes. Comfort grip T-handle rotates separately from the press plate for smooth bearing installation. Once the bearing has been set, use thebearingseatingtooltofinishinstallation.

3. SPECIFICATION Model no. ..................................................................... SMC3 Die sizes ..........................32, 36, 38, 42 (x3), 46mm Setting bar length ....................................................... 420mm Setting bar increments ..........................6 x 30mm, 1 x 42mm

4. OPERATION 4.1. TOP BEARING RACE INSERTION 4.1.1. Position top bearing race in headstock and select appropriate size die, one which is slightly smaller than the diameter of the bearing

race. 4.1.2. Slide the pressure plate onto the bearing setting bar allowing it to click into one of its positions. Then push the assembly up through the

headstock, bearing race and die. Wind the winding handle onto the bar and re-adjust the pressure plate to the correct setting (fig.3.2). 4.1.3. Wind the winding handle so that the bearing race is pushed into the headstock. When in place release the pressure plate (fig3.3).

SMC3 Issue 1 18/10/19Original Language Version Jack Sealey Limited

Refer to instructions

Wear eye protection

Wear protective gloves

Wear safety footwear

Wear protective clothing

Top Bearing Race

Bottom Bearing Race

fig.2fig.1

4.2. BOTTOM BEARING RACE INSERTION 4.2.1. Position bottom bearing race in headstock and select appropriate size die, one which is slightly smaller than the diameter of the

bearing race. 4.2.2. Slide the pressure plate onto the bearing setting bar, allowing it to click into one of its positions (fig.3.4). Continue to wind the winding

handle onto the bar so that the bearing race is pushed into the headstock (fig.3.5). When in place release the pressure plate and remove the assembly from the headstock.

4.2.3. To ensure that both bearing races are fully driven home, place the die onto the die handle, position it over the bearing race and using a soft faced hammer, drive the bearing race home. Return all parts to the case, and store in a safe, dry, childproof location.

5. PARTS

Original Language Version Jack Sealey Limited

Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR 01284 757500 01284 703534 sales@sealey.co.uk www.sealey.co.uk

ENVIRONMENT PROTECTION Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids according to local regulations.

Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice. Important: No Liability is accepted for incorrect use of this product. Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim.

Parts support is available for these products. Please

Manualsnet FAQs

If you want to find out how the SMC3 Sealey works, you can view and download the Sealey SMC3 Press Instruction Manual on the Manualsnet website.

Yes, we have the Instruction Manual for Sealey SMC3 as well as other Sealey manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Instruction Manual should include all the details that are needed to use a Sealey SMC3. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Sealey SMC3 Press Instruction Manual is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Sealey SMC3 Press Instruction Manual consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Sealey SMC3 Press Instruction Manual free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Sealey SMC3 Press Instruction Manual, simply download the document to your computer. Once downloaded, open the PDF file and print the Sealey SMC3 Press Instruction Manual as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.