Sealey PI1000.V4 Inverter Instruction Manual PDF

1 of 3
1 of 3

Summary of Content for Sealey PI1000.V4 Inverter Instruction Manual PDF

POWER INVERTER 1000W 12V DC - 230V 50HZ MODEL NO: PI1000.V4

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble free performance.

IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.

1. SAFETY DANGER! - Beware, lead-acid batteries generate explosive gases during normal battery operation. 9 Wash immediately with soap and water if battery acid contacts skin or clothing. If acid enters eye, flush immediately with cool

clean running water for at least 15 minutes and seek immediate medical attention. 8 DO NOT smoke or allow a spark or flame in the vicinity of the battery or engine. 9 If the battery terminals are corroded or dirty, clean them before attaching the clips. WARNING! To prevent the risk of sparking, short circuit and possible explosion DO NOT drop metal tools in the battery area,

or allow them to touch the battery terminals. 9 Before attaching to battery, remove personal metallic items such as rings, bracelets, necklaces and watches. A lead acid

battery can produce a short-circuit current which is high enough to weld such items to the vehicle and cause severe burns. 9 Keep children and unauthorised persons away from the working area. WARNING! DO NOT use on any vehicles other than those with 12V DC systems. WARNING! For delicate items such as laptops, an anti-surge device is recommended. 8 DO NOT install in compartment containing batteries or flammable liquids. 8 DO NOT connect to any AC power source. 8 DO NOT get inverter wet or use in damp or wet locations or areas where there is condensation. 8 DO NOT use the inverter for any purpose other than for which it is designed. 8 DO NOT pull the cables or clips from the battery terminals. 8 DO NOT operate the inverter if damaged. 8 DO NOT connect to a positive earthed system. Ensure you have the polarity correct before connecting, red clip to positive (+)

battery terminal and black clip to negative (-) battery terminal. 8 DO NOT obstruct ventilation or cover 9 Before connecting ensure nothing is plugged into the inverter, and the inverter is switched OFF. WARNING! Inverters become hot during use. 9 When not in use store inverter in a safe, dry, childproof location.

Modernvehiclescontainextensiveelectronicsystems.YouarerequiredtocheckwiththevehicleManufacturer,foranyspecific instructions regarding the use of this type of equipment on each vehicle.

2. INTRODUCTION Supplies continuous smooth 230V power from 12V DC power supply found in cars, caravans, boats and commercials. Suitable for powering small TVs, laptops, power tools and various other electrical equipment within the wattage rating of the inverter. Features USB port (5V/2.1A) for use on various domestic electronic equipment such as digital cameras and mobile phones. Aluminium case provides durability and maximum heat dissipation. Safety features include automatic overload shut-down, short circuit protection, low voltage alarm, low voltage shutdown and overheat shutdown. Supplied with battery leads.

3. SPECIFICATION Model No. .............................................................. PI1000.V4 Input Voltage ..............................................................12V DC Output Voltage ......................................................... 230V AC Continuous Output ......................................................1000W Maximum Output .........................................................2000W Output Frequency ..........................................................50Hz Dimensions (WxDxH) ....................................240x160x65mm Supply Connection ........................................... Battery Leads USB Output ................................................................5V 2.1A

PI1000.V4 Issue 2 (5) 04/12/20Original Language Version Jack Sealey Limited

Refer to instructions

Electrical shock hazard

Wear eye protection

Wear protective gloves

Keep in dry area protect from rain

4. SETUP & OPERATION 4.1. POWER SOURCE REQUIREMENTS 4.1.1. The inverter must be connected to a 12V DC negative earth system. DO NOT use with a positive earth system. 4.1.2. The power source must be capable of providing between 10.0V and 15.5V and able to supply the necessary current

to operate the load.

4.2. CONNECTING BATTERY LEADS TO INVERTER 4.2.1. To attach the Battery Leads loosen the terminal screws. (Fig.1). 4.2.2. Place the Black lead into the end of the Negative (-) terminal and tighten the terminal screw. 4.2.3. Place the Red lead into the end of the Positive (+) terminal and tighten the terminal screw.

4.3. EARTH CONNECTION 4.3.1. The chassis earth lug (See Fig.1) must be connected to an earthing point. In a vehicle connect the

chassis earth lug to the vehicles chassis. In a boat connect to the earthing system of the vessel. In a fixed location connect to the ground.

4.4. CONNECTING TO BATTERY TERMINALS 4.4.1. Ensure battery terminals are clean, if necessary clean away any corrosion. 4.4.2. Check to make sure the inverter is turned OFF and no flammable fumes are present. 4.4.3. Undo the securing bolt for the red (+) battery terminal and secure the red battery lead to the red (+) terminal post on the battery. 4.4.4. Undo the securing bolt for the black (-) battery terminal and secure the black battery lead to the black (-) terminal post on the battery. 4.4.5. Check all connections are secure. 4.5. CONNECTION TO LOAD 4.5.1. NOTE! Most electrical appliances, tools etc, have a rating plate indicating the power consumption in Amps or Watts. Use these ratings

to ensure you remain under the inverters maximum capacity. If the rating is shown in amps, multiply the value by the voltage (230V) to determine the wattage.

4.5.2. Ensure that the inverter is switched OFF. Plug the equipment you wish to use into one of the inverters two 3 pin sockets or into the USB port as required.

4.5.3. Make sure the load does not exceed the wattage rating of the inverter. 4.5.4. Switch the inverter on, check that everything is working and the green LED is lit.

WARNING! DO NOT connect the inverter to any AC distribution wiring or any AC load circuit in which the neutral conductor is connected to ground (earth) or to the negative of the DC (battery) source.

4.5.5. NOTE! Some rechargeable devices do not operate well with a moderated sine wave inverter. They only operate from a standard household outlet which provides a pure sine wave. It is recommended that these devices be operated from a standard household outlet only. This problem does not occur with most battery operated equipment. Most of these devices use a separate charger or transformer that is plugged into a separate AC socket.

4.6. PLACEMENT OF INVERTER 4.6.1. For best and safest operation the inverter should be placed on a flat and stable surface. 4.6.2. Use only in a dry location, do not allow inverter to get wet. 4.6.3. Use in cool ambient temperature of between 5C and 35C. Do not place on or near a heating vent. 4.6.4. Allow sufficient space around the inverter for cooling. If the inverter overheats it will shut down and will not restart until it has cooled

down. 8 DO NOT use near flammable materials or anywhere that flammable gasses could accumulate.

4.6.5. The inverter may become uncomfortably hot during extended periods of full power use. WARNING! DO NOT place on or near materials that may be affected by heat.

4.7. WATTAGE LOADING 4.7.1. Inductive loads, such as TVs and stereos, require more current to operate than do resistive loads of the same wattage rating.

Induction motors, as well as some televisions, may require 2 to 6 times their wattage rating to start up. The most demanding in thiscategoryarethosethatstartunderload,suchascompressorsandpumps.Testingistheonlydefinitivewaytodetermine whetheraspecificloadcanbestartedandhowlongitcanrun.Theunitwillsimplyshutdownifitisoverloaded.Torestarttheunit after a shut down due to overloading, remove the overload. NOTE! The inverter will not operate high wattage appliances, such as hair dryers, microwave ovens and toasters.

Original Language Version Jack Sealey Limited

fig.1

fig.2

PI1000.V4 Issue 2 (5) 04/12/20

Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR 01284 757500 01284 703534 sales@sealey.co.uk www.sealey.co.uk

ENVIRONMENT PROTECTION Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids according to local regulations.

WEEE REGULATIONS Dispose of this product at the end of its working life in compliance with the EU Directive on Waste Electrical and Electronic Equipment (WEEE). When the product is no longer required, it must be disposed of in an environmentally protective way. Contact your local solid waste authority for recycling information.

Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice. Please note that other versions of this product are available. If you require documentation for alternative versions, please email or call our technical team on technical@sealey.co.uk or 01284 757505. Important: No Liability is accepted for incorrect use of this product. Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim.

Original Language Version Jack Sealey Limited

4.8. BATTERY OPERATING TIME 4.8.1. With a typical vehicle battery, a minimum operating time of 1 to 2 hours can be expected depending on the load draw. It is

recommended that the operator starts the engine every hour to recharge the battery. This will prevent any unexpected shut down of the equipment and will ensure that there is always sufficient battery capacity to start the vehicle. The inverter may be used either with the engine running or turned off. However, the inverter must be switched OFF when starting the vehicle.

4.8.2. The inverter draws less than 0.45 Amperes from the battery when it is not supplying power to a load. In most cases, the inverter may be left connected to the battery when it is not in use. If the vehicle will not be used for several days, disconnect the unit from the battery.

5. PROTECTIVE FEATURE

FUNCTION State Description Restart work method

LED light Alarm AC Output

Input low voltage alarm Green on Red off

Alarm AC has output When the voltage of battery returns to required level, alarm stops automatically

Input low voltage shut down

Green on Red on

Alarm No AC output When the voltage of the battery returns to required level, the inverter will start working,

Input high voltage shut down

Green on Red on

No Alarm No AC output When the voltage of the battery returns to required level, the inverter will restart, green light on, red light off.

Overload protection Green on Red on

No Alarm No AC output Reduce the lo

Manualsnet FAQs

If you want to find out how the PI1000.V4 Sealey works, you can view and download the Sealey PI1000.V4 Inverter Instruction Manual on the Manualsnet website.

Yes, we have the Instruction Manual for Sealey PI1000.V4 as well as other Sealey manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Instruction Manual should include all the details that are needed to use a Sealey PI1000.V4. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Sealey PI1000.V4 Inverter Instruction Manual is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Sealey PI1000.V4 Inverter Instruction Manual consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Sealey PI1000.V4 Inverter Instruction Manual free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Sealey PI1000.V4 Inverter Instruction Manual, simply download the document to your computer. Once downloaded, open the PDF file and print the Sealey PI1000.V4 Inverter Instruction Manual as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.