Sealey VS2048.V3 Injector Instruction Manual PDF

1 of 3
1 of 3

Summary of Content for Sealey VS2048.V3 Injector Instruction Manual PDF

DIESEL INJECTION LEak baCk kITS Model no: VS2046.V2, VS2048.V3

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble free performance.

IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.

1. SafETy WaRNING! Ensure all Health and Safety, local authority, and general workshop practice regulations are strictly adhered to

when using this kit. 9 Maintaintools in a good clean condition for the best and safest performance. 8 DO NOT use test kit if parts are damaged. 9 Wear approved eye protection. A full range of personal safety equipment is available from your Sealey Stockist. 9 Wear suitable clothing to avoid snagging. DO NOT wear jewellery and tie back long hair. WaRNING! In a vehicle fitted with automatic transmission, select neutral or park. 9 Use proper ventilation and avoid breathing in exhaust fumes. 9 Keep a fire extinguisher to hand. 9 Protect hands from burns, as the engine will be hot after the test. 9 Account for all tools and parts being used, and DO NOT leave them in, or on the engine after use. 9 ensure that any collected diesel is disposed of correctly, in accordance with local authority guidelines. 8 DO NOT leave vehicles engine running unattended whilst the testing kit is fitted. IMPORTaNT: Always refer to the vehicle manufacturers service instructions, or a proprietary manual to establish the current procedure

and data. 9 These instructions for use are provided as a guide only.

2. INTRODuCTION Updated kit designed to measure return fuel flow on diesel vehicles up to 6 cylinders, fitted with common rail injection system. Identifies worn, blocked or inoperative injectors quickly and easily. Contains measurement tubes for short term tests and measurement bottles for long term, more accurate evaluation. Master kit includes range of adaptors to suit Bosch, delphi, new delphi and denso injectors for comprehensive coverage of common rail diesel vehicles. Supplied in carry-case.

3. OPERaTION 3.1. Most modern diesel vehicles are fitted with a sound deadening cowling over the top of the engine. If fitted, remove this cowling to

gain access to the engine. 3.2. Direct Connection Tubes (Bosch connectors only - see fig.1.5). These tubes are ideal for a vehicle which will not start, and

provide a very quick assessment. 3.2.1. The return pipes are retained by wire clips, remove the clips and store in a safe place. Gently ease out each of the return pipes

from the injectors (fig.2). Take care not to break the connectors as they can be brittle. 3.2.2. Plug the ends of the return pipes to avoid any spillage.

VS2048.V3 VS2046.V2

VS2048.V3 VS2046.V2 Issue 3 (HF) 18/10/18Original Language Version Jack Sealey limited

Refer to instructions

Wear a face shield

Wear protective gloves

Wear protective clothing

Warning! High Pressure

Fuel

3.2.3. Connect the tubes to each injector (fig.3), the wire clips are not required as the return system is low pressure. 3.2.4. Crank over the engine until the tubes are at least 50% full. Take care, that should the engine start, the tubes will fill up very

quickly. 3.2.5. Check the levels for each injector. The overall variation in the levels should be less than 10%. Any injector which has a back

leakage problem will have more diesel in the tube. 3.2.6. Remove the tubes from the injectors, taking care not to spill any diesel, place a finger over the end of the tube to hold the liquid in

the tube and then empty into a suitable container. 3.2.7. Refit the return pipes to the injectors and secure them with the wire clips as per the vehicle manufacturers workshop manual. 3.3. Flexible Tube, Adaptors and Bottles (fig.1.1, 2, 3, 4 and 6).These will provide a more accurate reading as the engine can

be left running for longer. 3.3.1. Remove the return pipes from the injectors. Refer to the appropriate vehicle manufacturers workshop manual. 3.3.2. Connect the appropriate, Bosch, Delphi or Denso adaptors to the flexible tubes. 3.3.3. Connect the flexible tubes to each injector and hang the bottle rack in a suitable position. 3.3.4. Start the engine (or crank over if it will not run), run until the one of the bottles is approximately 75% full, and stop the engine. 3.3.5. Check the levels for each injector. The overall variation in the levels should be less than 10%. Any injector which has a back

leakage problem will have more diesel in the tube. 3.3.6. Remove the tubes from the injectors, taking care not to spill any diesel, if possible lower the bottle rack to a level below that of the

injectors or raise the flexible tube, so that the fluid in the tubes drains into the bottles. 3.3.7. Refit the return pipes to the injectors as per the vehicle manufacturers workshop manual. NOTE: This system is designed to give a quick assessment of the return flow of the injectors, it is unable to determine all of the factors which may affect the operation of the vehicle.

4. PaRTS Part Part No. Description 1 VS2048.V2-01 Adaptor Set (Set of 6) (supplied as single pieces) (parts 1 to 4 are included in VS2047.V2 kit) 2 VS2048.V2-02 Adaptor Set (Set of 6) (supplied as single pieces) 3 VS2048.V2-03 Adaptor Set (Set of 6) (supplied as single pieces) 4 VS2048.V2-04 Adaptor Set (Set of 6) (supplied as single pieces) 5 VS2048.V2-05 Fluid Measure (Set of 6) (supplied as single pieces) (parts 5 and 6 are included in VS2046.V2 kit) 6 VS2048.V2-06 Bottle / Tube / Adaptor Assembly 7 VS2048.V3-08 Adaptor Set (Set of 6) (supplied as single pieces) New Delphi Ford Transit 2.4 engine code PHFA

Return Pipe

Measurement Tube or Flexible

Pipe

6

5

7

VS2048.V3 VS2046.V2 Issue 3 (HF) 18/10/18Original Language Version Jack Sealey limited

fig.1

fig.2

fig.3

Sealey Group, kempson Way, Suffolk business Park, bury St Edmunds, Suffolk. IP32 7aR 01284 757500 01284 703534 sales@sealey.co.uk www.sealey.co.uk

ENVIRONMENT PROTECTION Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids according to local regulations.

Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice. Importa

Manualsnet FAQs

If you want to find out how the VS2048.V3 Sealey works, you can view and download the Sealey VS2048.V3 Injector Instruction Manual on the Manualsnet website.

Yes, we have the Instruction Manual for Sealey VS2048.V3 as well as other Sealey manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Instruction Manual should include all the details that are needed to use a Sealey VS2048.V3. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Sealey VS2048.V3 Injector Instruction Manual is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Sealey VS2048.V3 Injector Instruction Manual consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Sealey VS2048.V3 Injector Instruction Manual free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Sealey VS2048.V3 Injector Instruction Manual, simply download the document to your computer. Once downloaded, open the PDF file and print the Sealey VS2048.V3 Injector Instruction Manual as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.