Sealey PPF30 Hydraulic Press Instruction Manual PDF

1 of 3
1 of 3

Summary of Content for Sealey PPF30 Hydraulic Press Instruction Manual PDF

20 & 30 TONNE PREMIER HYDRAULIC PRESSES - FLOOR TYPE MODEL NO: PPF20 , PPF30

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble free performance.

IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.

1. SAFETY 9 Familiarise yourself with the applications, limitations and hazards

of the press. 9 Maintain thepress in good condition (use an authorised service

agent). 9 Replace or repair damaged parts. Use recommended parts only.

Unauthorised parts may be dangerous and will invalidate the warranty.

9 Keep the press clean for best and safest performance. 9 Locate the press in a suitable work area, on a surface that is

stable, level, dry, not slippery, and capable of sustaining the load. 9 Keep area clean and tidy and free from unrelated materials, and

ensure there is adequate lighting. WARNING! Always wear approved eye or face protection when

operating the press. 9 Remove ill fitting clothing. Remove ties, watches, rings and other

loose jewellery, and contain long hair. 9 Keep hands and body clear of the work table when operating the

press. 9 Maintain correct balance and footing. DO NOT over reach. Ensure

the floor is not slippery and wear non-slip shoes. 9 Keep children and unauthorised persons away from the working

area. 8 DO NOT use the press for a task it is not designed to perform. 8 DO NOT adjust or tamper with the safety valve, or make any modifications to the press. 8 DO NOT exceed the rated capacity of the press. Avoid applying excessive force, use the pressure gauge to determine the applied load. 8 DO NOT apply off-centre loads. Ensure that workpiece is centrally loaded and correctly secured before operating the press. 8 DO NOT allow the workpiece or the arbor plates to fall from the press work bench. 8 DO NOT get the press wet or use in damp or wet locations or areas where there is condensation. 8 DO NOT operate the press when you are tired or under the influence of alcohol, drugs or intoxicating medication. 8 DO NOT climb upon the press. 8 DO NOT use if bent, broken, cracked, leaking or otherwise damaged, or if press has been subjected to a shock load. 8 DO NOT operate the press if any parts are missing as this may cause failure and/or possible personal injury. 8 DO NOT use the press to compress a spring or any other item that could disengage and cause a potential hazard. 8 DO NOT stand directly in front of loaded press and never leave loaded press unattended. 8 DO NOT allow untrained persons to operate the press. DANGER! This model is purpose designed to withstand greater loads than the hydraulic unit can develop. For safety reasons, always

ensure the workpiece and press tools are secured on the table and will not flex or suddenly give way, causing danger to operator or the workpiece.

WARNING! DO NOT use brake fluid, or any fluid other than a good quality jack oil, such as SEALEY HYDRAULIC JACK OIL, as this may cause serious damage to the press and will invalidate the warranty.

9 When not in use, release pressure from the pump and clean the press. Stand or store the arbors in a safe, childproof location.

2. INTRODUCTION Manufactured in Europe, a Professional range of floor and bench mount presses, ranging from 15tonne to 50tonne. Hydraulic elements are mounted in the frame to maximise workspace and protect components. Floor models incorporate a fast approach feature (foot pedal or handle operated depending on model). Model Nos PPF301 and PPF501 are air/hydraulic and fully operated by foot pedal to keep hands free for fine positioning of the workpiece. Storage for press pins included in frame (pins not included on Model Nos PPB15, PPF20 and PPF30). Suitable for workshop use or by the serious motoring enthusiast.

PPF20 , PPF30 Issue 3 (3, F) 08/11/21Original Language Version Jack Sealey Limited

Refer to instructions

Wear eye protection

3. SPECIFICATION Model No: . . . . . . . . . . . . . . . . . . . . . . . . . . . . PPF20 . . . . . . . . . . . . . . . . . . . . . PPF30 Capacity:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20tonne . . . . . . . . . . . . . . . . . . . . 30tonne Ram Stroke: . . . . . . . . . . . . . . . . . . . . . . . . . . 195mm . . . . . . . . . . . . . . . . . . . . . 195mm Ram Diameter: . . . . . . . . . . . . . . . . . . . . . . . . 51mm . . . . . . . . . . . . . . . . . . . . .58mm Maximum Height - Ram to Table:. . . . . . . . . . 858mm . . . . . . . . . . . . . . . . . . . . . 854mm Minimum Height - Ram to Table: . . . . . . . . . . 120mm . . . . . . . . . . . . . . . . . . . . . 120mm Table Aperture: . . . . . . . . . . . . . . . . . . . . . . . . 132mm . . . . . . . . . . . . . . . . . . . . . 132mm Working Table Depth: . . . . . . . . . . . . . . . . . . . 172mm . . . . . . . . . . . . . . . . . . . . . 172mm Working Table Width: . . . . . . . . . . . . . . . . . . . 448mm . . . . . . . . . . . . . . . . . . . . . 448mm Overall Height: . . . . . . . . . . . . . . . . . . . . . . . 1850mm . . . . . . . . . . . . . . . . . . . . 1850mm Gauge Included: . . . . . . . . . . . . . . . . . . . . . . . . . . .Yes . . . . . . . . . . . . . . . . . . . . . . . . Yes Optional Accessories . . . . . . . . . . . . . . . . . . . .YKPP8 . . . . . . . . . . . . . . . . . . . . . YKPP8

WARNING! these presses are heavy, the use of a lifting appliance is recommended. 3.1. FITTING THE FEET 3.1.1. Attach the permanent press feet (figs.1 & 2). 3.1.2. It is recommended that, for safest operation, the press is secured to the floor using

the fixing holes in the feet.

3.2. FITTING THE PUMP HANDLES 3.2.1. The press is supplied with the pump handles disconnected, to save damage in

transit (fig.3). 3.2.2. Cut the plastic ties to release the pump handles (fig.4). 3.2.3. Fix pump handle by means of screw, guide bush and nut (fig.5). 3.2.4. Fit the long pump handle into the socket of high speed pump (fig.6).

4. OPERATION 4.1. BLEEDING THE HYDRAULIC CIRCUIT 4.1.1. Before first use, any air trapped in the hydraulic circuit will need to be bled. 4.1.2. To do this: open the release valve and pump both pumps 10 times. 4.1.3. Close the release valve and pump a further 10 times. The ram should

extend. 4.1.4. Open the release valve again; the ram should retract. 4.1.5. If the hydraulic circuit still appears sluggish, repeat the process. 4.2. USING THE PRESS 4.2.1. Insert the saddle into the ram head and secure with the grub screw (fig.7). 4.2.2. Lift or lower the table to the required height and insert the pins to support it. 4.2.3. Place the arbor plate on the press bed frame, then place workpiece onto the

arbor plate and align beneath the ram as required. NOTE: care must be taken to ensure an arbor does not fall from the press work table. If necessary, fix in position. 4.2.4. Close the release valve by turning it clockwise fully. 4.2.5. Pump with the high speed pump until the saddle is close to the workpiece. 4.2.6. Use the low speed pump to perform the pressing operation, monitoring the

pressure via the pressure gauge. Using this pump allows greater control and feel.

4.2.7. When the operation is finished, release the pressure gradually by opening the release valve slowly.

4.2.8. When the ram has retracted fully, remove the work from the table. 4.2.9. When the press is not in use, ensure that the ram is retracted fully to help

avoid corrosion.

Original Language Version Jack Sealey Limited

fig.1

fig.2

fig.3 fig.4 fig.5

fig.6

fig.7

PPF20 , PPF30 Issue 3 (3, F) 08/11/21

5. MAINTENANCE NOTE: Maintenance and repair must only be carried out by a qualified person. Contact your Sealey stockist for details. 5.1. Lubricate all joints and moving parts periodically. 5.2. Always keep the press clean, dry and protected from harsh conditions. 5.3. To check hydraulic oil level, open the left hand top cover, and unscrew the oil filler screw

(fig.8). If oil needs replacing, use only Sealey hydraulic jack oil. DO NOT use brake fluid. Contact your local Sealey stockist for details). Replace oil filler screw and purge system of air.

5.4. When replacing the hydraulic oil, ensure the piston is fully retracted. 5.5. If press efficiency begins to drop, purge the system to eliminate any air from the

hydraulic system (see 5.1.). 5.6. When not in use, clean the press with a damp, soapy cloth. DO NOT use abrasive or

solvent cleaners. IMPORTANT! Owing to their size and weight, hydraulic products should ideally be repaired by local service agents. We have service / repairagents in most parts of the UK. Before returning your product please call our technical helpline on 01284 757505 for advice and trouble shooting guidance. If the product is under guarantee please contact your Sealey stockist.

Original Language Version Jack Sealey Limited

Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR 01284 757500 01284 703534 sales@sealey.co.uk www.sealey.co.uk

ENVIRONMENT PROTECTION Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids according to local regulations.

Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice. Important: No Liability is accepted for incorrect use o

Manualsnet FAQs

If you want to find out how the PPF30 Sealey works, you can view and download the Sealey PPF30 Hydraulic Press Instruction Manual on the Manualsnet website.

Yes, we have the Instruction Manual for Sealey PPF30 as well as other Sealey manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Instruction Manual should include all the details that are needed to use a Sealey PPF30. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Sealey PPF30 Hydraulic Press Instruction Manual is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Sealey PPF30 Hydraulic Press Instruction Manual consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Sealey PPF30 Hydraulic Press Instruction Manual free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Sealey PPF30 Hydraulic Press Instruction Manual, simply download the document to your computer. Once downloaded, open the PDF file and print the Sealey PPF30 Hydraulic Press Instruction Manual as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.