4. CONTENTS
WARNING! No user serviceable parts inside. DO NOT disassemble.
5. OPERATION WARNING! Ensure the hose is disconnected from the air supply. DO NOT position the hose in direct sunlight or in areas of
extreme heat or cold. A clearance of 750mm either side of the pivot position is required for a full 180 sweep of the casing. 5.1. WALL MOUNTING
WARNING! Ensure the wall is capable of holding the weight of unit and operation. 5.1.1. Remove all items from the packaging. 5.1.2. Using the pivot bracket, item 2, as a template, mark the wall or substantial post, where the hose reel is to be mounted and drill four 10mm diameter holes 50mm deep, 40mm centres horizontally and 164mm vertically. (Suggest 800mm approximately from the floor to the under edge of the hose reel casing). 5.1.3. Insert the four plastic plugs, item 4, into the holes and mount the bracket securely, flat face uppermost (fig.1), with the four self tapping screws, item 3. 5.1.4. With assistance, offer the hose reel pivot shaft into the pivot bracket, check for full sweep angle. No further fitting required. 5.1.5. Connect to an air line. DO NOT connect directly to an air tool, connect a leader hose to the tool first and then connect the leader hose to the air hose reel. 5.2. EXTENDING THE HOSE 5.2.1. Pull the hose out slowly to the length required and stop, pause momentarily to enable the ratchet to engage. Operate the air line by opening the tap or valve. 5.3. RETRACTING THE HOSE (SA822, SA823 AND SA824 ONLY) 5.3.1. Close the tap or valve. To release the hose and allow it to automatically rewind, pull the hose out from the locked position and then release the tension on the hose. Carry the air tool with the hose back to the hose reel housing.
WARNING! The reel tension is factory set, if any adjustment is required contact an authorised service agent.
6. MAINTENANCE WARNING! Before attempting maintenance or inspection, vent any pressure remaining in the hose.
To ensure reliable operation, clean the hose and casing regularly. DO NOT spray or wet the product, but clean with a damp cloth and warm water. DO NOT use solvents or detergents, as these may permanently damage the item. The hose reel does not require special maintenance as it is lubricated for life. If the product needs to be opened, consult your nearest authorised service agent.
WARNING: DO NOT attempt to loosen, or remove, any casing screws yourself. Replacement of the supply hose should be carried out by skilled personnel only, consult your nearest authorised service agent. STORAGE: Before storing the air hose, ensure it is clean and dry. Store it in a dark, safe, dry, childproof location, where the temperature will remain reasonably stable.
7. TROUBLESHOOTING Fault Possible Cause Possible remedy Hose will not retract
Hose extended too far and locked
Open the top lid and turn the reel to free the lock. ( g.3)
The spring has lost some torsion
Contact an authorised service agent. DO NOT attempt the repair yourself.
Hose twisted in housing. Draw the hose from the reel to check.
Torsion (main spring) fatigued.
Contact an authorised service agent. DO NOT attempt the repair yourself.
g.3
Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR 01284 757500 01284 703534 sales@sealey.co.uk www.sealey.co.uk
ENVIRONMENT PROTECTION Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids according to local regulations.
SA821.V2,SA822.V2,SA823.V2,SA824.V2 Issue 3 - 08/09/21Original Language Version Jack Sealey Limited
Item Description Qty Remarks
1 Hose Reel c/w Housing 1 Auto rewind
2 Pivot Bracket 1 Composite
3 Cross Head S/T Screw (plated)
4 No 14 x 48mm
4 Plastic Plug 4 9.5mm x 45mm
1 g.2
2
3
4 g.1
Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice. Please note that other versions of this product are available. If you require documentation for alternative versions, please email or call our technical team on technical@sealey.co.uk or 01284 757505. Important: No Liability is accepted for incorrect use of this product. Warranty: Guarantee is 12 months from purchase
en
