Sealey LED112.V2 Floodlight Instruction Manual PDF

SMD LED EXTRA SLIM FLOODLIGHT WITH WALL BRACKET MODEL NOS: LED112.V2, LED113.V2, LED115.V2

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble free performance.

IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.

1. SAFETY 1.1. ELECTRICAL WARNING! It is the users responsibility to read, understand and comply with the following: WARNING! THIS PRODUCT MUST BE INSTALLED BY A QUALIFIED ELECTRICIAN. You must check all electrical equipment and appliances to ensure they are safe before using. You must inspect power supply leads

and all electrical connections for wear and damage. You must ensure the risk of electric shock is minimised by the installation of appropriate safety devices. You must also read and understand the following instructions concerning electrical safety. Ensure the light is connected to an appropriate electrical on/o switch. Ensure the insulation on all cables and the product itself is safe before connecting to the mains power supply. Ensure that cables are always protected against short circuit and overload. Regularly inspect power supply, leads and all electrical connections for wear and damage, especially power connections, to ensure

that none are loose. Ensure the voltage marked on the product is the same as the electrical power supply to be used. DO NOT pull power cable once installed. DO NOT use worn or damaged leads, or connections. Immediately replace or have repaired by a quali ed Electrician. Ensure the unit is correctly earthed and wired according to the following. (Installation should be undertaken by a quali ed electrician)

a) Connect the green/yellow earth wire to the earth terminal E. b) Connect the brown live wire to live terminal L. c) Connect the blue neutral wire to the neutral terminal N. After wiring, check there are no bare wires, that all wires have been correctly connected.

1.2. GENERAL SAFETY WARNING! Turn o the mains power supply before servicing or performing any maintenance. Maintain the light in good condition (Repairs must only be undertaken by a quali ed electrician). Replace or repair damaged parts. Use genuine parts only, non authorised parts may be dangerous and will invalidate the warranty. Ensure the light is installed correctly in accordance with these instructions. Only install the light on a vertical surface. DO NOT x the light on any horizontal surface i.e. ceiling, or overhang. Ideally the Installation should be away from ammable or combustible materials such as wood, cloth, paper etc. DANGER! DO NOT direct the light into a persons eyes. This unit has a very intensive light output, which if incorrectly used could

cause eye damage. DO NOT install the light where it is likely to be knocked or hit. DO NOT install in bathrooms, shower rooms, sauna or such locations. DO NOT install near an exhaust outlet. i.e. boiler ue, dryer outlet, etc. DO NOT use the light without the front glass shield tted.

2. INTRODUCTION Mounted in die-cast powder coated aluminium extra slim housing with wall bracket. SMD LED technology allows ultra-bright illumination whilst still keeping costs lower than traditional halogen tubes. Even spread of light across a 110 angle. Supplied with power cable at 75cm only and suitable for outdoor mounting.

3. SPECIFICATION Model No: .......................................... LED112.V2 ........................... LED113.V2 ............................ LED115.V2 Colour Temperature: .................................. 6500K ...................................6500K ....................................6500K Dimensions (W x D x H): ........ 157 x 56 x 101mm ................195 x 57 x 152mm .................235 x 57 x 191mm IP Rating: ..................................................... IP65 ......................................IP65 .......................................IP65 LED Type: ................................................... SMD ..................................... SMD ...................................... SMD Lumen Output:..........................................1900lm ................................. 5200lm ............................... 10,000lm PIR Motion Sensor: .........................................No ........................................ No ......................................... No Power: .......................................................... 20W ......................................50W .....................................100W Supply: ........................................................ 230V .....................................230V ......................................230V

LED112.V2, LED113.V2, LED115.V2 Issue 1 23/12/21Original Language Version Jack Sealey Limited

Refer to instructions

4. ASSEMBLY WARNING! DO NOT connect unit to the mains power supply before installation.

4.1. INSTALLATION 4.1.1. Give careful consideration to the position of unit to ensure you obtain maximum bene t from the lighting range, and that an

appropriate electrical power source can be provided. 4.1.2. An approximate appropriate mounting height from the ground is 2.5m. See g.1. 4.1.3. This LED oodlight develops minimal heat and is not subject to the same mounting restrictions that apply to halogen lamps that

become too hot to touch. We do however recommend that the oodlight should not be placed in cramped or restrictive positions and should be xed at the following minimum distances between the light and any surface/object. See g.2.

500mm minimum between the top of the light and any overhead surface, or objects, i.e. ceilings, overhangs. 200mm between sides of light and wall/surfaces. 2 metres minimum between the front of the light and any object to be illuminated. Fix the light to a vertical surface with appropriate xings. Ensure the lamp is connected to the mains by a quali ed electrician.

5. MAINTENANCE 5.1. Clean the casing externally (not the glass) with a moist cloth.

DO NOT use solvents or abrasives to clean the light. 5.2. Avoid touching the glass shield as handling may reduce its serviceable life and cause the glass to crack. If necessary clean the

glass shield with alcohol and a soft cloth. Undo the single screw without removing it to clean internally. DO NOT use the light without the glass shield. DO NOT use the light without the weather seals intact.

g.1

g.2

Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR 01284 757500 01284 703534 sales@sealey.co.uk www.sealey.co.uk

ENVIRONMENT PROTECTION Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids according to local regulations.

WEEE REGULATIONS Dispose of this product at the end of its working life in compliance with the EU Directive on Waste Electrical and Electronic Equipment (WEEE). When the product is no longer required, it must be disposed of in an environmentally protective way. Contact your local solid waste authority for recycling information.

Original Language Version Jack Sealey Limited LED112.V2, LED113.V2, LED115.V2 Issue 1 23/12/21

Note: It is our policy to continually improve products and