Sealey HVD24P Fan Instruction Manual PDF

1 of 2
1 of 2

Summary of Content for Sealey HVD24P Fan Instruction Manual PDF

24,30,36 INDUSTRIAL HIGH VELOCITY DRUM FAN 230V - PREMIER MODEL NO: HVD24P, HVD30P, HVD36P

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble free performance.

IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.

1. SAFETY 1.1. ELECTRICAL SAFETY WARNING! It is the responsibility of the owner and the operator to read, understand and comply with the following:

You must check all electrical products, before use, to ensure that they are safe. You must inspect power cables, plugs, sockets and any other connectors for wear or damage. You must ensure that the risk of electric shock is minimised by the installation of appropriate safety devices. A Residual Current Circuit Breaker (RCCB) should be incorporated in the main distribution board. You must also read and understand the following instructions concerning electrical safety. Ensure that cables are always protected against short circuit and overload. Regularly inspect power supply cables and plugs for wear or damage and check all connections

to ensure that none are loose. Ensure that the voltage marked on the appliance matches the power supply to be

used and that the plug is tted with the correct fuse - see fuse rating at right. DO NOT use worn or damaged cables, plugs or connectors. Have any faulty item repaired or

replaced immediately by a competent electrician. It is recommended that this device is wired directly to a fused isolator switch. If, however, a plug

is tted, the following applies: Fit a new plug according to the following instructions (UK only).

a) Connect the GREEN/YELLOW earth wire to the earth terminal E. b) Connect the BROWN live wire to the live terminal L. c) Connect the BLUE neutral wire to the neutral terminal N. d) After wiring, check that there are no bare wires, that all wires have been correctly connected, that the cable restraint is tight. 1.2. GENERAL SAFETY Disconnect the fan from the mains power when not in use and before servicing or performing any maintenance. Use the fan in dry

areas only. DO NOT use in wet or areas with high condensation such as showers, pools etc. WARNING! If a fan falls into water or other liquid, immediately switch off and disconnect from the mains power supply. DO NOT

touch the fan until the mains power supply has been disconnected. Always disconnect the fan from the power supply when moving it from one location to another and ensure fan is stood on a level

surface. The fan air flow is powerful. Before use ensure that there is nothing nearby that will be damaged or displaced by the stream of air.

Keep the fan clean and maintained in good condition. For motor service contact an authorised service agent. Use recommended parts only. Unapproved parts may be dangerous, and will invalidate your warranty. DO NOT operate the fan where there are explosive or flammable gases, fumes or other hazardous substances. DO NOT insert any objects through the fan guard. DO NOT cover the fan when in use. DO NOT immerse the fan in water or any other liquid. DO NOT allow children to operate the fan.

NOTE: This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities or lack of experience and knowledge, unless they have been given supervision or instruction concerning the use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance.

2. INTRODUCTION High e ciency industrial fans with improved motor and blade design resulting in higher velocity with up to 30% more area coverage and reach. Robust unit with heavy-duty gauge steel casing, guard and frame. Handle, wheels and tilt function cradle stand, allow the control of air ow where it is needed. Carefully balanced and fully guarded blades provide safe operation. Suitable for industrial, commercial, agricultural, automotive and showroom applications. Fitted with 3-pin plug.

Recommended fuse rating HVD24P, HVD30P = 5 A

HVD36P = 13 A

HVD24P,HVD30P,HVD36P Issue 2 (3) 27/10/21Original Language Version Jack Sealey Limited

Refer to instructions

Indoor use only

3. SPECIFICATION Model No.: .......................................HVD24P..................................... HVD30P ........................................................... HVD36P Fan diameter: ...................................610mm (24) ........................... 760mm (30) ........................................915mm (36) Speeds: ............................................2................................................. 2 ................................................................................... 2 Speed range: ....................................1300 - 1420rpm ......................... 880 - 960rpm ........................................... 860 - 950rpm Maximum airflow: .............................266m/min (9420cfm) ................ 288m/min (10175cfm) ..............363m/min (12855cfm) Power: ..............................................330W ......................................... 315W ....................................................................410W Supply:..............................................230V .......................................... 230V ......................................................................230V Current:.............................................1.43A ......................................... 1.37A .....................................................................1.78A Overall efficiency: .............................31.4% ........................................ 32.1% ...................................................................31.7% Efficiency category: ..........................Static.......................................... Static ..................................................................... Static Efficiency grade: ...............................40.3N ......................................... 41.22N ............................................................... 40.21N Measurement category: ....................A ................................................ A ...................................................................................A VSD: .................................................No .............................................. No ............................................................................. No Optimum energy efficiency point: .....1399rpm .................................... 954rpm ...............................................................940rpm Rated pressure: ................................110Pa ........................................ 70Pa ......................................................................65Pa Rated flow rate:: ...............................1.116m/s ................................... 1.690m/s ....................................................... 2.242m/s

4. OPERATION WARNING! Ensure that you read, understand and apply safety instructions in Section 1 before using fan.

4.1. Check that the speed control is set to 0 (OFF) and then plug into the mains power supply and switch the power on. 4.2. The fans feature 2 speeds which are selectable using the switch located at the back of the fan, above the motor on the HVD24P or

on the fan housing (near the handle) on the HVD30P and HVD36P. 4.3. Adjust the direction of the air ow by moving from side to side and tilting the fan up or down as required. 4.4. When you have nished using the fan ensure you turn the speed control switch to 0 (OFF) and disconnect the fan from the mains

power.

5. CARE OF FAN WARNING! Ensure that the fan is disconnected from the mains power supply before attempting any of the following:

5.1. Use a soft, damp cloth to clean the fan. DO NOT immerse the fan in water and never allow water to drip onto the motor housing. DO NOT use solvents, petroleum, paint thinner or other chemicals to clean the fan.

5.2. To clean the fan blade, undo the cross headed screws around the circumference, remove the grille and clean the blade with a slightly damp cloth. Replace the grille as required and re t the cross headed screws.

5.3. Should the motor, switch or the power lead require service or maintenance contact your local service agent. 5.4. When not in use place the fan in its original box or otherwise cover to protect from dust, and store in a safe childproof location.

HVD24P,HVD30P,HVD36P Issue 2 (3) 27/10/21Original Language Version Jack Sealey Limited

Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR 01284 757500 01284 703534 sales@sealey.co.uk www.sealey.co.uk

ENVIRONMENT PROTECTION Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids according to local regulations.

WEEE REGULATIONS Dispose of this product at the end of its working life in compliance with the EU Directive on Waste Electrical and Electronic Equipment (WEEE). When the product is no longer required, it must be disposed of in an environmentally protective way.

Manualsnet FAQs

If you want to find out how the HVD24P Sealey works, you can view and download the Sealey HVD24P Fan Instruction Manual on the Manualsnet website.

Yes, we have the Instruction Manual for Sealey HVD24P as well as other Sealey manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Instruction Manual should include all the details that are needed to use a Sealey HVD24P. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Sealey HVD24P Fan Instruction Manual is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Sealey HVD24P Fan Instruction Manual consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Sealey HVD24P Fan Instruction Manual free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Sealey HVD24P Fan Instruction Manual, simply download the document to your computer. Once downloaded, open the PDF file and print the Sealey HVD24P Fan Instruction Manual as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.