Sealey DDE01.V2 Extractor Instruction Manual PDF

1 of 2
1 of 2

Summary of Content for Sealey DDE01.V2 Extractor Instruction Manual PDF

3.7V VACUUM DRILL DUST EXTRACTOR MODEL NO: DDE01.V2

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble free performance.

IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.

1. SAFETY 1.1. GENERAL SAFETY

8 DO NOT use this device in direct sunlight. 8 DO NOT allow the dust extractor to get wet. 8 DO NOT allow unqualified persons or children to operate this device.

1.2. LASER SAFETY The DDE01 utilises a Class II laser that emits a low level of visible radiation (i.e. a wavelength of 650 nanometres) which is safe for the skin but not inherently safe for the eyes. The Class II emission limit is set at the maximum level for which eye protection is normally afforded by natural aversion responses to bright light. Accidental eye exposure is therefore normally safe, although the natural aversion response can be overridden by deliberately staring into the beam, and can also be influenced by the use of alcohol or drugs.

8 DO NOT direct the laser beam at any persons (or animals) eyes as eye damage could result. 8 DO NOT operate the laser level when you are tired or under the influence of alcohol, drugs or

intoxicating medication. Be aware that reflections of the laser beam from mirrors or other shiny surfaces can be as hazardous as direct eye exposure.

2. INTRODUCTION 3.7V Vacuum holds unit to the wall for easy drilling. Suitable for drill bits up to 12mm. Features a horizontal and vertical spirit level for accurate positioning. Laser light on the bottom for accurate positioning of holes, for example in a sequence or a square. Removable dust collection pod for easy emptying. Rechargeable Lithium-ion powered.

3. SPECIFICATION Model No:............................................................. DDE01.V2 Maximum Drilling Diameter: ......................................... 12mm

4. OPERATION NOTE: The vacuum seal on this product is only suitable for smooth conforming surfaces. 4.1. DRILLING A HOLE 4.1.1. Mark position of hole that you want to drill. If drilling more than one

hole in succession the laser guides can be used to line up with your markings (fig.1).

4.1.2. There is a small gap in the bristles on-top of the device that allow you to see your prepared markings. Line up your mark with this hole. You can also use the lasers and spirit levels to help with this.

4.1.3. When happy with your placement turn on the suction (fig.2). The device will now be stuck to the wall. The vacuum can be released using the button on the side of the body (fig.2).

4.2. EMPTYING THE COLLECTOR 4.2.1. The device can be slid apart leaving you with two pieces. The dust

collection pod and the suction device (fig.3). 4.2.2. The dust collection pod comes apart by gently pressing the tabs on

the sides. Once apart the dust should be safely disposed of. NOTE: The dust is collected via gravity and not suction. 4.3. CHARGING THE UNIT 4.3.1. Seperate the dust pod to expose the charging port on the end face

of the unit (fig.4). 4.3.2. Connect the USB charge cable to the charge socket on the body.

fig.1

Compressor On/Off

Laser On/Off

Vacuum Release

Spirit Levels

Dust Collection Pod

fig.2

fig.3

Original Language Version Jack Sealey Limited

Refer to instructions

Warning Laser Wear eye protection

Wear a mask

DDE01.V2 Issue 1 29/03/21

4.3.3. Whilst charging, the LED to the side of the port will show red. Once fully charged this will show green.

5. MAINTENANCE 5.1. Dispose of waste according to local regulations. 5.2. Wipe unit clean with a damp cloth.

Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR 01284 757500 01284 703534 sales@sealey.co.uk www.sealey.co.uk

ENVIRONMENT PROTECTION Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids according to local regulations.

WEEE REGULATIONS Dispose of this product at the end of its working life in compliance with the EU Directive on Waste Electrical and Electronic Equipment (WEEE). When the product is no longer required, it must be disposed of in an environmentally protective way. Contact your local solid waste authority for recycling information.

BATTERY REMOVAL: SEE SECTION 4.3 Under the Waste Batteries and Accumulators Regulations 2009, Jack Sealey Ltd are required to inform potential purchasers of products containing batteries (as defined within these regulations), that they are registered with Valpaks registered compliance scheme. Jack Sealey Ltd Batteries Producer Registration Number (BPRN) is BPRN00705.

DDE01.V2 Issue 1 29/03/21Original Language Version Jack Sealey Limited

BATTERY REMOVAL Under the Waste Batteries and Accumulators Regulations 2009, Jack Sealey Ltd are required to inform potential purchasers of products containing batteries (as defined within these regulations), that they are registered with Valpaks registered compliance scheme. Jack Sealey Ltds Batteries Producer Registration Number (BPRN) is BPRN00705.

Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice. Please note that other versions of this product are available. If

Manualsnet FAQs

If you want to find out how the DDE01.V2 Sealey works, you can view and download the Sealey DDE01.V2 Extractor Instruction Manual on the Manualsnet website.

Yes, we have the Instruction Manual for Sealey DDE01.V2 as well as other Sealey manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Instruction Manual should include all the details that are needed to use a Sealey DDE01.V2. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Sealey DDE01.V2 Extractor Instruction Manual is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Sealey DDE01.V2 Extractor Instruction Manual consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Sealey DDE01.V2 Extractor Instruction Manual free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Sealey DDE01.V2 Extractor Instruction Manual, simply download the document to your computer. Once downloaded, open the PDF file and print the Sealey DDE01.V2 Extractor Instruction Manual as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.