Sealey DS01 Drill Stand Instruction Manual PDF

1 of 3
1 of 3

Summary of Content for Sealey DS01 Drill Stand Instruction Manual PDF

instructions for

Drill stanD with cast iron base 500mm & 65mm vice model no: Ds01

thank you for purchasing a sealey product. manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble free performance.

IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.

1. safety 9 only use on firm, level, unobstructed surfaces which are capable of

supporting the stand and drill. 9 ensure stand is fixed to surface capable of supporting stand, drill

and work piece. 9 replace or repair damaged parts. use only recommended parts.

unauthorised parts may be dangerous and will invalidate the warranty. warninG! failure to comply with these instructions may result in damage

to the stand or other property and/or personal injury. warninG! the warnings, cautions and instructions discussed in this

instruction manual cannot cover all possible conditions and situations that may occur. it must be understood that common sense and caution are factors which cannot be built into this product, but must be applied by the operator.

2. introDuction drill stand with cast iron base for vertical drilling using a hand drill. supplied with drill vice which mounts onto the base to secure the workpiece. features a preset depth control and stop for drilling depths of up to 60mm, ideal for accurate and repetitive drilling. for use with hand drills with a collar diameter of 38mm if used with the adaptor bush or 43mm if used without. drill vice features a quick jaw release feature to allow fast and easy adjustment to suit the workpiece.

3. specification model no ....................................................................... ds01 collar centre to column ............................................. 150mm maximum distance collar to base .............................. 345mm column diameter ......................................................... 25mm Base size ............................................................155x220mm collar diameter .................. 43mm (38mm with adapter bush) overall Height ............................................................ 500mm Vice Jaw Width ............................................................. 65mm Vice Jaw depth ............................................................ 25mm Vice Jaw opening ........................................................ 70mm

4. assembly 4.1. slide the column into the base, making sure that it is level with the bottom of the base. clamp in place with bolt. 4.2. slide the lower collar onto column and position half way. UseHexkeytolockinplace.(fig.2.)

ds01 | issue 1 22/01/18Original Language Version Jack sealey limited

refer to instructions

fig.1

fig.2

Wear eye protection

Wear protective gloves

4.3. slide the head assembly onto the column. 4.4. Apply a small amount of light lubricant to the column to ease movement. 4.5. Attach the operating lever to the head assembly andtheconnectingarm.(fig.3.) 4.6. Keep the Hex key in magnetic clips on side of head assembly.

4.7. Usethetwoboltssuppliedtosecurethevicetothebase.(fig.4.) 4.8. Bolt the base to a work bench (bolts not supplied). 4.9. the vice has a quick release/adjustment button. Press to release the thread then slide in and out to quickly adjust jaw opening, release button to engage screw thread.

4.10. Position an electric drill with standard 43mm diameter neck into the head assembly. tighten the locking collar using the hex key. 4.11. the head assembly has a reducing sleeve provided to use with 38mm drill necks.

4.12. setting the depth Gauge 4.12.1. determine the depth of hole required. 4.12.2. release the locking bolt. 4.12.3. lower the drill using the drill stand handle to the required reading on the depth gauge, lock the depth adjusting rod with the locking bolt.

ds01 | issue 1 22/01/18Original Language Version Jack sealey limited

fig.3

fig.4

fig.5

fig.6

ds01 | issue 1 22/01/18Original Language Version Jack sealey limited

sealey Group, Kempson way, suffolk business park, bury st edmunds, suffolk. ip32 7ar 01284 757500 01284 703534 sales@sealey.co.uk www.sealey.co.uk

environment protection recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids according to local regulations.

note: it is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice. important: no liability is accepted for incorrect use of this product. warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim.

4.13. Drilling a hole. 4.13.1. lower the head assembly until the drill bit touches the work piece. 4.13.2. lock the head assemble in place.

Manualsnet FAQs

If you want to find out how the DS01 Sealey works, you can view and download the Sealey DS01 Drill Stand Instruction Manual on the Manualsnet website.

Yes, we have the Instruction Manual for Sealey DS01 as well as other Sealey manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Instruction Manual should include all the details that are needed to use a Sealey DS01. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Sealey DS01 Drill Stand Instruction Manual is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Sealey DS01 Drill Stand Instruction Manual consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Sealey DS01 Drill Stand Instruction Manual free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Sealey DS01 Drill Stand Instruction Manual, simply download the document to your computer. Once downloaded, open the PDF file and print the Sealey DS01 Drill Stand Instruction Manual as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.