Sealey MS0630 Dolly Instruction Manual PDF

1 of 2
1 of 2

Summary of Content for Sealey MS0630 Dolly Instruction Manual PDF

MOTORCYCLE DOLLY REAR WHEEL - SIDE STAND TYPE MODEL NO: MS0630

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble free performance.

IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.

1. SAFETY 9 Maintain thedolly in good condition (use an authorised service agent). 9 Replace or repair damaged parts. Use genuine parts only. Unauthorised parts may be dangerous and will invalidate the warranty. 9 Locate the dolly in a suitable work area. Keep area clean and tidy and free from unrelated materials, and ensure that there is adequate

lighting. 9 Ensure that the floor is level and strong enough (preferably concrete) to take the weight of the dolly and the motorcycle. 8 DO NOT use the dolly on tarmacadam, as the surface may be unstable. 9 Keep the dolly clean for best and safest performance. 9 The maximum motorcycle weight is 500kg. DO NOT exceed this rated capacity. 9 Use appropriate straps to secure the motorcycle to the dolly when manoeuvring. 9 Pull rather than push the motorcycle when manoeuvring on the dolly to reduce the risk of pushing the motorcycle off its side stand. 9 Maintain correct balance and footing, DO NOT over reach. Ensure the floor is not slippery and wear non-slip shoes. Keep children and

unauthorised persons away from the work area. 8 DO NOT use the dolly for a task it is not designed to perform. 8 DO NOT use the dolly if it is damaged. 8 DO NOT use the dolly when you are tired or under the influence of alcohol, drugs or intoxicating medication. 8 DO NOT allow untrained persons to use the dolly. 8 DO NOT make any modifications to the dolly. 9 Before storing in safe area, ensure that all parts are clean and free of grease and oil.

WARNING!: The warnings, cautions and instructions in this manual cannot cover all possible conditions and situations that may occur. It must be understood that common sense and caution are factors which cannot be built into this product, but must be applied by the operator.

2. INTRODUCTION Motorcycle dolly holds a single motorcycle with a side stand, weighing up to 500kg. Easy to manoeuvre around the workshop or garage. Front wheel stays in contact with the ground allowing the motorcycle to be steered into the desired position. Pivoting feature allows flexibility in side stand designs. Side stand holder can be adjusted to cater to the majority of motorbikes.

3. SPECIFICATION Model No. .................................................................MS0630 Max. Capacity ..............................................................500Kg Overall Dimensions (LxW) ..............................1300 x 650mm Loading Track Dimensions(L x W x H) ..............550 x 250mm

MS0630 Issue 1 24/02/21Original Language Version Jack Sealey Limited

Refer to Instruction

Manual

4. ASSEMBLY

Part No. Description QTY.

1. Platform For Arm 1.

2. Hx Hd Set Screw M10 x 15mm Zinc

2.

3. Arm 1.

4. Skt Cap Bolt M10 x 30mm 5.

5. Nylon Locknut M10 Zinc 5.

6. Swivel Castor 3.

7. Platform 1.

8. Swivel Castor (c/w Brake) 2.

9. M10 Plain Washer 10.

4.1. Remove with care all contents from outer packaging and check parts against parts list. 4.2. Place frame (1) on ground attach 2 castors with brakes (8) using flat washers (9), and nylon locknuts (5). 4.3. Attach castors (6) using flat washers (9), and nylon locknuts (5). 4.4. Place supporting arm (8) on ground attach wheel (10) using flat washer (5), spring washer (4) and nut with cap (3). 4.5. Using M10 set screw (2), bolt main part (7) and support arm (3) together. The support arm can move in relationship to main part

and can be adjusted to position/design of side stand before bolt being tightened fully.

5. OPERATION WARNING! Ensure that you read, understand and apply the safety instructions before use. WARNING! DO NOT attempt to overload the dolly.

5.1. LOADING 5.1.1. Position the dolly in a suitable area, checking that the surface on which the dolly will be used is solid and flat. 5.1.2. Apply the brakes to the two wheels 5.1.3. Push the motorcycle onto the dolly, positioning the rear wheel centrally on the main part and support with the side stand on the

support arm. Adjust as required and fix in position by tightening set screw. Front wheel remains on ground. 5.1.4. Secure the motorcycle using suitable straps. 5.1.5. Release the brakes to allow the dolly to be manoeuvred. 5.2. UNLOADING 5.2.1. Apply the brakes to the two wheels. 5.2.2. Holding handle bars lift side stand and remove the motorcycle from the dolly. 5.2.3. Store the dolly in a safe, dry, childproof location with the brakes on.

6. MAINTENANCE 6.1. Before use, check the frame assembly and platform for cracks and damage. 6.2. Regularly check that all fasteners are tight. 6.3. Periodically lubricate the castors.

Original Language Version Jack Sealey Limited

Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR 01284 757500 01284 703534 sales@sealey.co.uk www.sealey.co.uk

Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice. Important: No Liability is accepted for incorrect use of this product. Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim.

ENVIRONMENT PROTECTION Recycle unwanted materials instead of disposing of them as waste. All tools, accessories a

Manualsnet FAQs

If you want to find out how the MS0630 Sealey works, you can view and download the Sealey MS0630 Dolly Instruction Manual on the Manualsnet website.

Yes, we have the Instruction Manual for Sealey MS0630 as well as other Sealey manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Instruction Manual should include all the details that are needed to use a Sealey MS0630. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Sealey MS0630 Dolly Instruction Manual is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Sealey MS0630 Dolly Instruction Manual consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Sealey MS0630 Dolly Instruction Manual free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Sealey MS0630 Dolly Instruction Manual, simply download the document to your computer. Once downloaded, open the PDF file and print the Sealey MS0630 Dolly Instruction Manual as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.