Sealey RE101.V3 Dent Puller Instruction Manual PDF

1 of 2
1 of 2

Summary of Content for Sealey RE101.V3 Dent Puller Instruction Manual PDF

Air Suction Dent Puller Model no: re101.V3

thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble free performance.

IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.

1. SAfety WArninG! ensure Health & Safety, local authority and general workshop practice regulations are adhered to when using this

equipment. WArninG! disconnect from the air supply before changing the suction cups, servicing or performing any maintenance. 9 Maintain the puller in good condition (use an authorised service agent). Before each use check condition of tool. If any component is

worn or damaged, replace immediately. Use genuine parts only. Unauthorised parts may be dangerous and will invalidate the warranty. 8 Do not operate the puller if any parts are damaged or missing as this may cause failure and/or personal injury. 9 Use in a suitable work area. Keep area free from unrelated materials and ensure that there is adequate lighting. WArninG! Always wear approved eye (or face) and hand protection when operating the puller. 9 Remove ill fitting clothing, ties, watches, rings, other loose jewellery and contain and/or tie back long hair. 9 Keep air hose away from heat, oil and sharp edges. Check air hose for wear before each use and ensure that all connections are

secure. WArninG! ensure correct air pressure is maintained and not exceeded. Working pressure is 90psi. 8 Do not attempt to attach the suction cup to a person as severe bruising and/or damage to internal organs can occur. 8 Do not place air line attachments close to your face and Do not point at other people or animals. 8 Do not direct air from the air line at yourself or others. 8 Do not carry the puller by the hose, or yank the hose from the air supply. 9 Maintain correct balance and footing. Do not over reach, ensure the floor is not slippery, wear non-slip footwear. 9 Keep children and unauthorised persons away from the working area. 9 ensure workpiece is secure before operating the puller. 8 Do not operate the puller when you are tired or under the influence of alcohol, drugs or intoxicating medication. 8 Do not clean the suction cups with solvents or other harsh chemicals. 8 Do not use the puller for any purpose other than that for which it is designed. 9 When not in use disconnect from air supply, return parts to the case, and store it in a safe, dry, childproof location.

2. introDuction Air activated suction pad keeps firm hold of panel while slide hammer is used to ease out dents and depressions without damage to the paint surface. Ideal for initial panel reshaping. Supplied with 75, 100 and 125mm suction pads and hook.

3. SPecificAtion Model no: ................................................................... Re101 Hook length:................................................................ 90mm nett Weight: ................................................................ 4.29kg overall length:........................................................... 590mm Recommended Air Pressure: ...............................72.5-116psi Suction Pads: .............................................75, 100, 125mm Working Pressure:......................................................... 90psi

4. oPerAtion 4.1. ensure that the panel to be worked on is dry, clean and free of

grease. 4.2. Select the appropriate size suction cup and screw it onto the slide

hammer and remove the protective cover from the cup. 4.3. ensure the valve is in the off position (90 to handle). Connect

the slide hammer to an air line with a suitable rated supply pressure - between 72psi and 116psi (working pressure is 90psi).

4.4. Position the suction cup over the dent and press it gently onto the body panel.

4.5. open the air valve, the suction cup will form a vacuum, firmly attaching it to the body panel.

4.6. Using the slide hammer, pull the dent out. Do not apply excessive force to the slide hammer. 4.7. When finished, turn the air valve off and remove the puller from the body panel.

fig.1

Re101.V3 Issue 1 24/10/18Original Language Version Jack Sealey limited

Refer to instructions

Wear eye protection

Wear protective gloves

Wear safety footwear

Wear protective clothing

4.8. disconnect from the air supply, remove the suction cup from the puller and refit the protective cover. Place all parts back in the case and store it in a safe, dry, childproof location.

4.9. Alternatively, weld a wavy wire strip to the panel, then use the hook in conjunction with the sliding hammer to pull out a dent.

5. MAintenAnce 5.1. Check condition of the suction cups regularly, if damaged, replace them using genuine parts only. 5.2. Always keep the suction cups clean and free of oil and grease. Clean them regularly with a non-aggressive cleaner. 5.3. In order to preserve elasticity, Do not expose suction cups to sunlight over an extended period of time. 5.4. Keep the tool in a clean, serviceable condition, using a slightly dampened cloth to clean it.

fig.2

Sealey Group, Kempson Way, Suffolk Business Park, Bury St edmunds, Suffolk. iP32 7Ar 01284 757500 01284 703534 sales@sealey.co.uk www.sealey.co.uk

enVironMent Protection Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids according to local regulations.

note:

Manualsnet FAQs

If you want to find out how the RE101.V3 Sealey works, you can view and download the Sealey RE101.V3 Dent Puller Instruction Manual on the Manualsnet website.

Yes, we have the Instruction Manual for Sealey RE101.V3 as well as other Sealey manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Instruction Manual should include all the details that are needed to use a Sealey RE101.V3. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Sealey RE101.V3 Dent Puller Instruction Manual is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Sealey RE101.V3 Dent Puller Instruction Manual consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Sealey RE101.V3 Dent Puller Instruction Manual free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Sealey RE101.V3 Dent Puller Instruction Manual, simply download the document to your computer. Once downloaded, open the PDF file and print the Sealey RE101.V3 Dent Puller Instruction Manual as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.