Sealey RE225.V3 Compressor Instruction Manual PDF

1 of 4
1 of 4

Summary of Content for Sealey RE225.V3 Compressor Instruction Manual PDF

1600KG COIL SPRING COMPRESSOR KIT MODEL NO: RE225.V3

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble free performance.

IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.

1. SAFETY DANGER! Stop compressing the spring before the coil windings touch. WARNING! Ensure Health & Safety, local authority, and general workshop practice regulations are adhered to when using this

equipment. 9 Before each use, check the unit for full functional capability. If the functional capability is not ensured or if damage is detected, the unit

should not be used and you should contact your supplier immediately. WARNING! Wear approved safety eye protection (standard spectacles are not adequate) and protective gloves. WARNING! DO NOT compress the spring to an extent where the jaws touch. 8 DO NOT use the compressor for other purposes than it was designed for and DO NOT OVERLOAD the compressor. 8 DO NOT operate spring compressor if parts are damaged or missing as this may cause failure and/or personal injury. 9 Maintain the spring compressor in good condition. Replacement or repair of damaged parts must be carried out by competent

personnel. Use genuine parts only. Unauthorised parts may be dangerous and will invalidate the warranty. 8 DO NOT force the spring compressor to achieve a task it was not designed to perform. 8 DO NOT allow untrained persons to use the spring compressor. 9 Familiarise yourself with the applications, limitations and potential hazards of the spring compressor. 9 Keep the work area clean, uncluttered and ensure there is adequate lighting. 9 Keep hands and body clear of the spring when operating the spring compressor. 9 Maintaincorrectbalanceandfooting.Ensurethefloorisnotslipperyandwearnon-slipshoes. 9 Removeillfittingclothes.Removeties,watches,rings,otherloosejewellery.Containand/ortiebacklonghair. 9 For indoor use and at room temperature only. 9 When not in use clean and store the spring compressor in a safe, dry, childproof location. 9 The coil spring compressor is exclusively for compressing and expanding McPherson strut springs for maintenance. The compressor

is not for removal of struts from any vehicle. Suitable jaws must be used. Any other or further use is considered not as intended. SEEALSOOPERATIONALSAFETYSECTION4.1

2. INTRODUCTION Highquality,Europeanmade,1600kgcoilspringcompressorkit.Suppliedwithtwopairsofdrop-forgedsafetyyokes,withpolyurethaneinserts for improved grip. Yokes are carefully shaped to prevent coil spring from bowing. Features Safety restraint wire as a precaution, in the unlikely event of a spring slipping. Suitable for use with air impact wrench.

3. SPECIFICATION Model no: ...............................................................RE225.V3 Yokespecification: Size (spring diameter) Small: ........................................................80-120mm(x2) Large: ........................................................80-195mm(x2) Drive: .................................................................... 27mm hex Maximum jaw opening: .............................................. 335mm Capacity: .................................................................... 1600kg

4. OPERATION 4.1. OPERATIONAL SAFETY 4.1.1. Whencompressingthespring,neitherthespringwindingsnorthejawsshouldcomeincontactwitheachother,seefigureB. 4.1.2. The centre line of the spring must always be parallel to the compressing device, especially for conical springs. 4.1.3. Use only suitable jaws for the springs. The spring must rest securely within the outer rib and the safety ridges. Take care that the

spring cannot slide out of the jaws. 4.1.4. Pay attention to compressed spring. Never drop or impact compressed spring, which can cause serious injury. 4.1.5. Use only for coil springs mentioned in this user instruction. 4.1.6. Theboltsofthejawsmustalwaysbefirmlytightenedwith60Nmtorque.

8 DO NOT make any construction changes to the unit, especially to the safety pin. 8 DO NOT leave compressed spring unattended.

RE225.V3Issue:3(3)26/10/2021Original Language Version Jack Sealey Limited

Refer to instruction

manual

Wear a face shield

Wear protective

gloves

WARNING! Crushingof

hands

DO NOT allow coils to touch

Keep in mind that compressed spring has a huge energy. The instruction may not cover all hazards. ALWAYS BE CAREFUL when using the coil spring compressor to prevent injury.

9 Before and during the clamping process, as well as after each operation, the correct position of the spring in the jaws shall be inspected and maintained.

4.2. OPERATION CONTROLS 1Drivenut 2Compressingdevice 3 Retaining bolts 4Jaws 5 Safety pin 6Outerrib 7 Safety ridge 8 Spring

4.3. OPERATION 4.3.1. REMOVE THE MCPHERSON SPRING STRUT 4.3.1.1. Before each operation, the McPherson spring strut must be removed from vehicle (refer to vehicle manufacturer). 4.3.1.2. Make sure to use the RIGHT SIZE of jaws. Select jaws and mount on the spring compressor. Make sure the spring is clean where the

jaws are mounted on the windings. Wipe away grease and dirt. 4.3.1.3. Fittheretainingboltsandtightenfirmly.

IMPORTANT IT IS VERY IMPORTANT FOR OPERATORS SAFETY THAT THE BOLTS OF THE JAWS ARE FIRMLY TIGHTENED. CHECK BOLT TORQUE (60NM PERIODICALLY). 4.3.2. Rotate the drive nut to drive the jaws apart to match the length of the spring and to compress as many windings as possible. 4.3.2.1. Mountthecompressoronavicebyclampingthefrontheadofthecompressorasbelow,seefig.E.Makesurethattheseatingofthe

spring windings in the jaws is correct. Make sure that the spring compressorisinthecentreofthespringwindings,seefig.Babove.

fig.B

D

8 7

3

7 6 4

3 4

3 4

2

1

A B

5

fig. C fig.D

fig. E

Original Language Version Jack Sealey Limited RE225.V3Issue:3(3)26/10/2021

fig.A fig.B

4.3.3. SAFETY WIRE 4.3.3.1. Always make sure that the safety wire is securely installed around the spring, and that the quick link is locked before starting the

compressing or decompressing process. Make sure that the wire does not get pinchedduringtheprocess,seefig.sF,G&H.

4.3.3.2. If needed, the wire can be slid out of the retaining slots in order to allow more space for the compressing process. Always remember to snap the wire back in place upon completion of your work.

4.3.4. Rotate the drive nut to drive the jaws apart to match the length of the spring and to compress as many windings as possible. See Figure I below.

4.3.5. Make sure the spring is clean where the jaws are mounted on the windings. 4.3.6. Preloadthecompressorbyturningthehandwheeluntilthejawshaveafirmgriponthespring,seefig.J. 4.3.7.. Compressthespringbyrotatingthedrivenutusingasocketwrench.(Limittorqueto120Nm,inordernottooverloadthesafetypin).

8 DO NOT continue to drive when the upper or lower travel ends of spring compressor are reached. 4.3.8. When the spring has been safely compressed, remove the top bearing of the strut. 4.3.9. Before removing thebearingrecheckthatthespringisstillfirmlyseatedinthejaws.SeefigureK.

4.3.10. Remove the damper and carefully release the tension on the spring. 4.3.11. Replace worn parts and repeat above procedure in reverse order for safe assembly. 4.3.12. Store the compressor in a safe and proper place after use.

IMPORTANT Take care throughout the whole operation and avoid standing in hazardous places in case the spring releases unintentionally.

5. MAINTENANCE 5.1. Maintenancepersonnelshouldbequalifiedandtrainedinthecompressorfunctionsandfailuremodes,theirrectification,operationand

maintenance of the product. 5.2. Regularcheckperiod:1month.Ifyoufindanydamageordeformation,pleasestopuseimmediatelyandaskyoursupplyingstockist

for help. Never try to repair the product yourself, except for changing the safety pin. 5.3. Always keep the unit clean. Make sure the coil spring compressor is dry. Always pack the jaws away with the compressor as delivered. 5.4. Store the unit in a dry place to prevent corrosion. Always pack away the jaws with the coil spring compressor as supplied. 5.5. Grease the guide spindle (using graphite grease) if necessary, or at least every six months. Always clean the spindle before applying

grease. Unauthorised parts are forbidden.

fig. Jfig. I

fig. K fig. L

Original Language Version Jack Sealey Limited RE225.V3Issue:3(3)26/10/2021

fig. F fig. G fig. H

Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR 01284 757500 01284 703534 sales@sealey.co.uk www.sealey.co.uk

Original Language Version Jack Sealey Limited

ENVIRONMENT PROTECTION Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids according to local regulations.

Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice. Please note that other versions of this product are available. If you require documentation for alternative versions, please email or call ourtechnicalteamontechnical@sealey.co.ukor01284757505. Important: No Liability is accepted for incorrect use of this product. Warranty:Guaranteeis12monthsfrompurchasedate,proofofwhichisrequiredforanyclaim.

RE225.V3Issue:3(3

Manualsnet FAQs

If you want to find out how the RE225.V3 Sealey works, you can view and download the Sealey RE225.V3 Compressor Instruction Manual on the Manualsnet website.

Yes, we have the Instruction Manual for Sealey RE225.V3 as well as other Sealey manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Instruction Manual should include all the details that are needed to use a Sealey RE225.V3. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Sealey RE225.V3 Compressor Instruction Manual is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Sealey RE225.V3 Compressor Instruction Manual consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Sealey RE225.V3 Compressor Instruction Manual free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Sealey RE225.V3 Compressor Instruction Manual, simply download the document to your computer. Once downloaded, open the PDF file and print the Sealey RE225.V3 Compressor Instruction Manual as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.