Sealey SG16.V4 Coating Gun Instruction Manual PDF

1 of 2
1 of 2

Summary of Content for Sealey SG16.V4 Coating Gun Instruction Manual PDF

INSTRUCTIONS FOR

UNDERBODY COATING SPRAY GUN AIR OPERATED DELUXE MODEL MODEL NO: SG16.V4

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble free performance.

IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.

1. SAFETY WARNING! Disconnect the gun from the air supply before changing accessories, servicing or performing any maintenance. 9 Maintain the gun in good condition. Replace or repair damaged parts. Use recommended parts only. Non-authorised parts may be

dangerous and will invalidate the warranty. 9 Keep the gun clean and rinse out the nozzle/injection probe and pipes with thinners after use. WARNING! If the gun components become blocked there is a danger of excessive pressure building up in the unit, causing the

canister to burst. 9 Wear the appropriate approved personal protective equipment when using the gun. A full range of personal protective equipment is

available from your Sealey dealer. 9 Locate the gun in a suitable, well ventilated area, keep area clean, tidy and free from unrelated materials and ensure there is

adequate lighting. 9 Ensure that a vehicle that has been jacked up is adequately supported with axle stands. 9 Removeillfittingclothing.Removeties,watches,ringsandotherloosejewelleryandcontainlonghair. 9 Keep children and unauthorised persons away from the working area. 9 Avoid unintentional operation. 9 Ensure the coating/wax manufacturers instructions are carefully adhered too. 8 DO NOT hold the gun or attachments close to your face (especially eyes, ears, etc.) and DO NOT point the gun or air hose at other

persons or animals. 8 DO NOT carry by the air hose, or pull the hose or the gun from the air supply. 8 DO NOTusethegunforanypurposeotherthanforwhichitisdesignedanddonotfillwithanyotherfluid. 8 DO NOT operate the gun if damaged. 9 When not in use, disconnect from the air supply and store in a safe, dry, childproof area. WARNING! The warnings, cautions and instructions in this manual cannot cover all possible conditions and situations that

may occur. It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be applied by the operator.

2. INTRODUCTION Features air control valve, making it suitable for various applications. Supplied with canister and wax injection probe.

3. SPECIFICATION Model no: ................................................................SG16.V4 Air pressure: ............................................................60-115psi Air consumption: ..................................................... 10-13cfm Air inlet size:..............................................................1/4BSP

4. CONTENTS

Item No Description Qty

1 Gun 1

2 Canister 1

3 Nozzle 1

4 Canister Cap 1

5 Injection Probe 1

6 Hose Fitting 1

7 Air control valve 1

SG16.V4| Issue 1 15/09/16Original Language Version Jack Sealey Limited

Refer to the instruction

manual

Wear eye protection

Wear a mask

5. OPERATION 5.1. Coupling 5.1.1. . Ensure the air valve is in the off position before connecting to the air supply. 5.1.2. An air pressure of no more than 8bar (115psi) and an air volume of 10cfm will be required.

WARNING! Ensure the air supply does not exceed 8bar (115psi). Too high a pressure will shorten the product life and may be dangerous, causing damage and/or personal injury.

5.1.3. Drain the air supply tank daily. Water in the air line will damage the gun. 5.1.4. Clean the air inlet filter screen weekly. 5.1.5. For recommended hook-up, see fig.1. 5.1.6. Line pressure should be increased to compensate for unusually long air hoses (over 8 meters). The minimum hose diameter should

be 1/4 internal diameter and fittings must have compatible dimensions. 5.1.7. Keep hoses away from heat, oil and sharp edges. Check hoses for wear, and make certain that all connections are secure.

WARNING! Ensure you read, understand and apply the safety instructions in Section 1 and follow the manufacturers instructions on the underseal/wax container. 5.2. Preparing the gun for use. 5.2.1. Pour the underseal/wax into the SG16.V4 canister, screwthecanisterontothegun,(fig.2.A). 5.2.2. Attachnozzle(fig.2.C)tothegun.Ensurethatthe nozzleisnotscrewedtoofarintothegunasthiswillaffecttheefficiencyofthedelivery.Tightenthenozzlelocknut. 5.2.3. Ensure the air supply is regulated to no more than 8bar (115psi) and then attach the air hose to the gun. 5.2.4. Adjusttheaircontrolvalvetoachievethedesiredflowofmaterialbeingapplied. 5.2.5. Aim the nozzle of the gun into a safe area and depress the gun trigger to check for correct operation. It may be necessary to adjust

the position of the nozzle in the gun to achieve the most effective delivery. 5.3. Using the injection probe 5.3.1. TheSG16.V4issuppliedwithaninjectionprobe(fig.2.D)for use with wax.Theflexibleinjectionprobeenableswaxtobesprayed

into cavities, between panels and inside doors etc. 5.3.2. Theinjectionprobe(fig.2.D)isinterchangeablewiththenozzle(fig.2.C)onthegun.Removethelocknutfromthenozzleandattach

ittotheinjectionprobe.Ensurethattheinjectionprobeisnotscrewedtoofarintothegunasthiswillaffecttheefficiencyofthe delivery.Tightenthelocknuttoholdtheinjectionprobeinpositionandattachthecanister(fig.2.A)tothegun.

5.3.3. Ensure the air supply is regulated to no more than 8bar (115psi) and then attach the air hose to the gun. 5.3.4. Adjusttheaircontrolvalvetoachievethedesiredflowofmaterialbeingapplied. 5.3.5. Aim the injection probe into a safe area and depress the gun trigger to check for correct operation. It may be necessary to adjust the

position of the injection probe in the gun to achieve the most effective delivery.

6. MAINTENANCE WARNING! Ensure the gun is disconnected from the air supply before attempting any maintenance. It is very important to keep the

gun and components clean to ensure free passage for the underseal/wax. 6.1. After use clean all items thoroughly, especially the probe, with a suitable cleaning agent and allow to dry before storage.

NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice. IMPORTANT: No liability is accepted for incorrect use of this product. WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.

Sole UK Distributor, Sealey Group.

Kempson Way, Suffolk Business Park,

Bury St. Edmunds, Suffolk.

IP32 7AR

www.sealey.co.uk

sales@sealey.co.uk

01284 757500

01284 703534

Web

fig.1 fig.2

Environmental Protection Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted,

taken to a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely unserviceable and requires disposal, drain off any fluids (if applicable)

<

Manualsnet FAQs

If you want to find out how the SG16.V4 Sealey works, you can view and download the Sealey SG16.V4 Coating Gun Instruction Manual on the Manualsnet website.

Yes, we have the Instruction Manual for Sealey SG16.V4 as well as other Sealey manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Instruction Manual should include all the details that are needed to use a Sealey SG16.V4. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Sealey SG16.V4 Coating Gun Instruction Manual is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Sealey SG16.V4 Coating Gun Instruction Manual consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Sealey SG16.V4 Coating Gun Instruction Manual free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Sealey SG16.V4 Coating Gun Instruction Manual, simply download the document to your computer. Once downloaded, open the PDF file and print the Sealey SG16.V4 Coating Gun Instruction Manual as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.