- Manuals
- Brands
- Sealey
- Bottle Jack
- AM30.V3
- Instruction Manual
Sealey AM30.V3 Bottle Jack Instruction Manual PDF
Summary of Content for Sealey AM30.V3 Bottle Jack Instruction Manual PDF
instructions for
bottle jacks 20/30tonne air/hydraulic model no: aM20.V3 & aM30.V3
thank you for purchasing a sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. saFety WarninG! alWays use load rated stands to suPPort liFted loads. danGer! use the jack for lifting and lowering only. danGer! do not place any part of the body under the lifted load unless the load is fully supported by rated stands, see
symbol 3. danGer! do not place any part of the body beneath the load during lifting and lowering.
8 do not modify the jack in any way. 8 the load to be lifted should never exceed the rated capacity of the jack. 8 the maximum stroke of the jack indicated on the label should never be exceeded. 9 the jack should be supported on a solid, level and horizontal surface which is well illuminated and free of obstructions. never stand
the jack on a surface which may sink. 9 the air supply hose should not be worn and connections should be in good condition. Keep the hose clean and away from heat, dirty
areas or sharp edges and do not bend it. 9 ensure that there are no persons inside the vehicle to be lifted. 9 switch off the engine and apply vehicle handbrake (put automatics in Park). 9 ensure the vehicle or element to be lifted against any type of sliding. use chocks. 9 do not enter the vehicle or start the engine whilst it is supported on the jack or appropriate stands. 9 Position the jack under the manufacturers recommended lifting point for the vehicle and ensure that it is not corroded, dirty or greasy.
this point should remain centred over the jack saddle. All off-centred loads can slip and accidents may result. 9 Duringraisingandloweringoftheload,allprecautionsshouldbetakentoavoidmovementofthevehicleload.Trafficmaycausethe
raised vehicle to rock during roadside use of the jack. 9 it is necessary for the operator to be able to observe the lifting device and the load during all movements. in the presence of
dangerous conditions, such as movement of the vehicle, etc, the lifting process must be interrupted. 9 ensure that there are no persons or obstructions underneath the vehicle prior to lowering. 9 Asanadditionalsafetymeasureagainstoverload,thejackisfittedwithanoverloadvalvesetatthefactorywhichshouldnotbe
adjusted under any circumstances. 9 ensure that the jack is undamaged and in good working order. 9 Keep the jack clean, particularly the load face of the saddle. 9 take immediate action to repair or replace any damaged parts. 9 use only approved parts/accessories obtained from a sealey supplier. The use of non-approved items could be dangerous and will
invalidate the warranty. 9 ensure that the jack is maintained by a qualified person and that the recommended hydraulic oil is used.
2. introduction Air hydraulic bottle jacks capable of both air assisted or manual operation. fitted with safety overload valve and manufactured in the eu. All steel, one piece base, reservoir and air cylinder design gives added strength. fully serviceable ram piston with extension screw. Both models supplied with 90 rotating pump and telescopic pump handle and have moulded carry handles incorporating storage for the pump handle. service kits readily available.
3. sPeciFication model no: ......................................................................Am20 capacity: ......................................................................20tonne minimum height: ............................................................234mm maximum height: ...........................................................447mm Piston stroke: .................................................................138mm Weight: ...........................................................................15.5kg
Am20.V3, Am30.V3| issue 1 20/09/16Original Language Version Jack sealey limited
refer to instructions
Wear safety footwear
chock wheels Pump to raise undo valve to
lower
use axle stands to lower after use
lubricate here
model no: ......................................................................Am30 capacity: ......................................................................30tonne minimum height: ............................................................242mm maximum height: ...........................................................455mm Piston stroke: .................................................................138mm 1 Weight: ...........................................................................23.5kg
4. PreParation 4.1. connect air supply 4.1.1. Anin-linefilterisrecommended,draindaily.Draincompressortankdaily. 4.1.2. Before connecting air supply hose ensure trigger is not pressed down. 4.1.3. Ensureconstantairpressureismaintainedduringoperation:7-10kg/cmandaminimumairflowof28ltr/min. 4.2. bleed system 4.2.1. Prior to using the jack, eliminate any air that may have accumulated in the system. 4.2.2. Position the lever in the release valve and turn once in an anti-clockwise direction. 4.2.3. Place the lever into the lever support and pump the jack several times to ensure internal lubrication and the elimination of accumulated air.Alternatively,presstriggerAofthevalvebriefly. 4.2.4. Place the lever in release valve again and close it in a clockwise direction. 4.2.5. Jack is now ready for operation.
5. oPeration iMPortant! Prior to lifting the load ensure that all of the above safety instructions are followed. 5.1. the feed screw of the jack, compliments its stroke, do not fully extend it. 5.2. liFtinG 5.2.1. close the release valve fully and press trigger of the air hose. lifting may also be performed by fully moving the lever downwards to
obtain greater speed by using the full stroke range of the piston. 5.3. loWerinG 5.3.1. slowly turn the release valve in an anticlockwise direction using the lever. ensure that there are no persons or obstacles under the
vehicle to be lowered. 5.3.2. the lowering speed is controlled by the amount of the valve is opened. 5.3.3. during lowering air is eliminated through a small hole in connector c, this is normal. 5.4. Shouldthejackbeoverloaded,itisfittedwithanoverloadvalvewhichwillpreventthe vehicle from being lifted. 5.5. never move the jack with the lever in the release valve as this will cause damage. 5.6. do not attempt to move the jack by pulling on the plastic air supply tube.
6. Maintenance iMPortant! Both the maintenance and repair of the jack may only be performed by qualifiedpersons,whohavesufficientknowledgeofthehydraulicsystemsusedinthese devices as a result of their training and experience. 6.1. Keep the jack clean and lubricate all moving parts at regular intervals, which must be clean and protected from aggressive conditions at all times. 6.2. only original spare parts should be used. 6.3. Prior to each use, check for bent, broken, cracked or loose parts and solve the problem. if it is suspected that the jack has been
subjectedtoabnormalloadsorhassufferedanyknocks,withdrawitfromserviceuntiltheproblemhasbeenrectified. 6.4. Iftheoillevelneedstobecheckedorrefilled,withthepistonfullyretracted,removethefillerpluganddrainitscontentsintoa
container. 6.5. Refillwithoil.UseagoodqualityoilsuchasSealeyhydraulicjackoil.do notusebrakefluid.Bleedsystemasinsection
4.2.Replaceoilfillerplug.Ensurenodirtentersthehydraulicsystemwhendraining,fillingremovingorreplacingcomponents. Annual oil replacement is recommended for jacks in daily use.
iMPortant too much oil may render the jack inoperative. 6.6. When the jack is not in use, the screw, main piston and the pump piston should be retracted to avoid corrosion. 6.7. remove the handle from its position. iMPortant: no resPonsibility is accePted For incorrect use oF this Product. Hydraulic products are only repaired by local service agents. We have service/repair agents in all parts of the UK. DO NOT reTurN prODucT TO us. Please telephone us on 01284 757500 to obtain the address and phone number of your local agent. If product is under guarantee please contact your dealer.
de-commissioning Product should the product become completely unserviceable and require disposal, draw off the oil into an approved container and dispose of the product and the oil according to local regulations. 6.8. Preventative maintenance 6.8.1. When the jack is not in use, keep piston and rod fully retracted. store the jack on its base in an upright position, in a well protected area,
where it will not be exposed to corrosion, abrasive dust, or other harmful elements. 6.8.2. Visually inspect jack before each use. take corrective action if any of the following are found: a. cracked or damaged housing b. excessive wear, bending or other damage c. leaking hydraulic fluid d. scored or damaged piston or rod e. incorrectly functioning swivel head or adjustment screw f. loose hardware g. modified or altered equipment
Am20.V3, Am30.V3| issue 1 20/09/16Original Language Version Jack sealey limited
NOTe: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice. iMPortant: no liability is accepted for incorrect use of this product. Warranty: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
sole uK distributor, sealey Group.
Kempson Way, suffolk Business Park,
Bury st. edmunds, suffolk.
iP32 7Ar
www.sealey.co.uk
sales@sealey.co.uk
01284 757500
01284 703534
Web
Problem cause solution erratic action Air in system
Viscosity of oil too high ram sticking or binding
With jack sitting on its base and ram retracted, bleed air from unit, see section 4.2 change to lower viscosity oil look for dirt or gummy deposits, leaks, misalignment, worn parts or defective packing.
ram does not advance release valve is open low/no oil in reservoir Air locked in system load is above capacity of system
close release valve fill with oil and bleed system Bleed the system use correct equipment
ram extends only partially low oil level in reservoir Piston rod is binding.
fill with oil to oil line and bleed system. look for dirt, gummy deposits, leaks, misalignment, worn parts or defective packing.
ram advances slowly Pump not working correctly
leaking seals
take jack to authorised service centre for pump repair. repair with seal kit
ram advances but does not hold pressure
Pump check valve not working
ram seals are leaking
take jack to authorised service centre for seal replacement repair with seal kit
Jack leaks oil Worn or damaged seals repair with seal kit
ram will not retract or retracts slowly release valve is closed reservoir is too full ram damaged internally
open release valve drain oil to correct level take jack to authorised service centre for repair
environmental Protection recycle unwanted materials instead of disposing of them as waste. all tools, accessories and packaging should be
sorted, taken to a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely unserviceable and requires disposal, drain off any fluids (if applicable)
into approved containers and dispose of the product and the fluids according to local regulations.
Am20.V3, Am30.V3| issue 1 20/0
Related manuals for Sealey AM30.V3 Bottle Jack Instruction Manual
Manualsnet FAQs
If you want to find out how the AM30.V3 Sealey works, you can view and download the Sealey AM30.V3 Bottle Jack Instruction Manual on the Manualsnet website.
Yes, we have the Instruction Manual for Sealey AM30.V3 as well as other Sealey manuals. All you need to do is to use our search bar and find the user manual that you are looking for.
The Instruction Manual should include all the details that are needed to use a Sealey AM30.V3. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.
The best way to navigate the Sealey AM30.V3 Bottle Jack Instruction Manual is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.
This Sealey AM30.V3 Bottle Jack Instruction Manual consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.
You can download Sealey AM30.V3 Bottle Jack Instruction Manual free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.
To be able to print Sealey AM30.V3 Bottle Jack Instruction Manual, simply download the document to your computer. Once downloaded, open the PDF file and print the Sealey AM30.V3 Bottle Jack Instruction Manual as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.