Sealey AM20.V3 Bottle Jack Instruction Manual PDF

1 of 3
1 of 3

Summary of Content for Sealey AM20.V3 Bottle Jack Instruction Manual PDF

instructions for

bottle jacks 20/30tonne air/hydraulic model no: aM20.V3 & aM30.V3

thank you for purchasing a sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble free performance.

IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.

1. saFety WarninG! alWays use load rated stands to suPPort liFted loads. danGer! use the jack for lifting and lowering only. danGer! do not place any part of the body under the lifted load unless the load is fully supported by rated stands, see

symbol 3. danGer! do not place any part of the body beneath the load during lifting and lowering.

8 do not modify the jack in any way. 8 the load to be lifted should never exceed the rated capacity of the jack. 8 the maximum stroke of the jack indicated on the label should never be exceeded. 9 the jack should be supported on a solid, level and horizontal surface which is well illuminated and free of obstructions. never stand

the jack on a surface which may sink. 9 the air supply hose should not be worn and connections should be in good condition. Keep the hose clean and away from heat, dirty

areas or sharp edges and do not bend it. 9 ensure that there are no persons inside the vehicle to be lifted. 9 switch off the engine and apply vehicle handbrake (put automatics in Park). 9 ensure the vehicle or element to be lifted against any type of sliding. use chocks. 9 do not enter the vehicle or start the engine whilst it is supported on the jack or appropriate stands. 9 Position the jack under the manufacturers recommended lifting point for the vehicle and ensure that it is not corroded, dirty or greasy.

this point should remain centred over the jack saddle. All off-centred loads can slip and accidents may result. 9 Duringraisingandloweringoftheload,allprecautionsshouldbetakentoavoidmovementofthevehicleload.Trafficmaycausethe

raised vehicle to rock during roadside use of the jack. 9 it is necessary for the operator to be able to observe the lifting device and the load during all movements. in the presence of

dangerous conditions, such as movement of the vehicle, etc, the lifting process must be interrupted. 9 ensure that there are no persons or obstructions underneath the vehicle prior to lowering. 9 Asanadditionalsafetymeasureagainstoverload,thejackisfittedwithanoverloadvalvesetatthefactorywhichshouldnotbe

adjusted under any circumstances. 9 ensure that the jack is undamaged and in good working order. 9 Keep the jack clean, particularly the load face of the saddle. 9 take immediate action to repair or replace any damaged parts. 9 use only approved parts/accessories obtained from a sealey supplier. The use of non-approved items could be dangerous and will

invalidate the warranty. 9 ensure that the jack is maintained by a qualified person and that the recommended hydraulic oil is used.

2. introduction Air hydraulic bottle jacks capable of both air assisted or manual operation. fitted with safety overload valve and manufactured in the eu. All steel, one piece base, reservoir and air cylinder design gives added strength. fully serviceable ram piston with extension screw. Both models supplied with 90 rotating pump and telescopic pump handle and have moulded carry handles incorporating storage for the pump handle. service kits readily available.

3. sPeciFication model no: ......................................................................Am20 capacity: ......................................................................20tonne minimum height: ............................................................234mm maximum height: ...........................................................447mm Piston stroke: .................................................................138mm Weight: ...........................................................................15.5kg

Am20.V3, Am30.V3| issue 1 20/09/16Original Language Version Jack sealey limited

refer to instructions

Wear safety footwear

chock wheels Pump to raise undo valve to

lower

use axle stands to lower after use

lubricate here

model no: ......................................................................Am30 capacity: ......................................................................30tonne minimum height: ............................................................242mm maximum height: ...........................................................455mm Piston stroke: .................................................................138mm 1 Weight: ...........................................................................23.5kg

4. PreParation 4.1. connect air supply 4.1.1. Anin-linefilterisrecommended,draindaily.Draincompressortankdaily. 4.1.2. Before connecting air supply hose ensure trigger is not pressed down. 4.1.3. Ensureconstantairpressureismaintainedduringoperation:7-10kg/cmandaminimumairflowof28ltr/min. 4.2. bleed system 4.2.1. Prior to using the jack, eliminate any air that may have accumulated in the system. 4.2.2. Position the lever in the release valve and turn once in an anti-clockwise direction. 4.2.3. Place the lever into the lever support and pump the jack several times to ensure internal lubrication and the elimination of accumulated air.Alternatively,presstriggerAofthevalvebriefly. 4.2.4. Place the lever in release valve again and close it in a clockwise direction. 4.2.5. Jack is now ready for operation.

5. oPeration iMPortant! Prior to lifting the load ensure that all of the above safety instructions are followed. 5.1. the feed screw of the jack, compliments its stroke, do not fully extend it. 5.2. liFtinG 5.2.1. close the release valve fully and press trigger of the air hose. lifting may also be performed by fully moving the lever downwards to

obtain greater speed by using the full stroke range of the piston. 5.3. loWerinG 5.3.1. slowly turn the release valve in an anticlockwise direction using the lever. ensure that there are no persons or obstacles under the

vehicle to be lowered. 5.3.2. the lowering speed is controlled by the amount of the valve is opened. 5.3.3. during lowering air is eliminated through a small hole in connector c, this is normal. 5.4. Shouldthejackbeoverloaded,itisfittedwithanoverloadvalvewhichwillpreventthe vehicle from being lifted. 5.5. never move the jack with the lever in the release valve as this will cause damage. 5.6. do not attempt to move the jack by pulling on the plastic air supply tube.

6. Maintenance iMPortant! Both the maintenance and repair of the jack may only be performed by qualifiedpersons,whohavesufficientknowledgeofthehydraulicsystemsusedinthese devices as a result of their training and experience. 6.1. Keep the jack clean and lubricate all moving parts at regular intervals, which must be clean and protected from aggressive conditions at all times. 6.2. only original spare parts should be used. 6.3. Prior to each use, check for bent, broken, cracked or loose parts and solve the problem. if it is suspected that the jack has been

subjectedtoabnormalloadsorhassufferedanyknocks,withdrawitfromserviceuntiltheproblemhasbeenrectified. 6.4. Iftheoillevelneedstobecheckedorrefilled,withthepistonfullyretracted,removethefillerpluganddrainitscontentsintoa

container. 6.5. Refillwithoil.UseagoodqualityoilsuchasSealeyhydraulicjackoil.do notusebrakefluid.Bleedsystemasinsection

4.2.Replaceoilfillerplug.Ensurenodirtentersthehydraulicsystemwhendraining,fillingremovingorreplacingcomponents. Annual oil replacement is recommended for jacks in daily use.

iMPortant too much oil may render the jack inoperative. 6.6. When the jack is not in use, the screw, main piston and the pump piston should be retracted to avoid corrosion. 6.7. remove the handle from its position. iMPortant: no resPonsibility is accePted For incorrect use oF this Product. Hydraulic products are only repaired by local service agents. We have service/repair agents in all parts of the UK. DO NOT reTurN prODucT TO us. Please telephone us on 01284 757500 to obtain the address and phone number of your local agent. If product is under guarantee please contact your dealer.

de-commissioning Product should the product become completely unserviceable and require disposal, draw off the oil into an approved container and dispose of the product and the oil according to local regulations. 6.8. Preventative maintenance 6.8.1. When the jack is not in use, keep piston and rod fully retracted. store the jack on its base in an upright position, in a well protected area,

where it will not be exposed to corrosion, abrasive dust, or other harmful elements. 6.8.2. Visually inspect jack before each use. take corrective action if any of the following are found: a. cracked or damaged housing b. excessive wear, bending or other damage c. leaking hydraulic fluid d. scored or damaged piston or rod e. incorrectly functioning swivel head or adjustment screw f. loose hardware g. modified or altered equipment

Am20.V3, Am30.V3| issue 1 20/09/16Original Language Version Jack sealey limited

NOTe: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice. iMPortant: no liability is accepted for incorrect use of this product. Warranty: Guarantee is 12 months from purchase date, proof of which will be required for any claim.

sole uK distributor, sealey Group.

Kempson Way, suffolk Business Park,

Bury st. edmunds, suffolk.

iP32 7Ar

www.sealey.co.uk

sales@sealey.co.uk

01284 757500

01284 703534

Web

Problem cause solution erratic action Air in system

Viscosity of oil too high ram sticking or binding

With jack sitting on its base and ram retracted, bleed air from unit, see section 4.2 change to lower viscosity oil look for dirt or gummy deposits, leaks, misalignment, worn parts or defective packing.

ram does not advance release valve is open low/no oil in reservoir Air locked in system load is above capacity of system

close release valve fill with oil and bleed system Bleed the system use correct equipment

ram extends only partially low oil level in reservoir Piston rod is binding.

fill with oil to oil line and bleed system. look for dirt, gummy deposits, leaks, misalignment, worn parts or defective packing.

ram advances slowly Pump not working correctly

leaking seals

take jack to authorised service centre for pump repair. repair with seal kit

ram advances but does not hold pressure

Pump check valve not working

ram seals are leaking

take jack to authorised service centre for seal replacement repair with seal kit

Jack leaks oil Worn or damaged seals repair with seal kit

ram will not retract or retracts slowly release valve is closed reservoir is too full ram damaged internally

open release valve drain oil to correct level take jack to authorised service centre for repair

environmental Protection recycle unwanted materials instead of disposing of them as waste. all tools, accessories and packaging should be

sorted, taken to a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely unserviceable and requires disposal, drain off any fluids (if applicable)

into approved containers and dispose of the product and the fluids according to local regulations.

Am20.V3, Am30.V3| issue 1 20/0

Manualsnet FAQs

If you want to find out how the AM20.V3 Sealey works, you can view and download the Sealey AM20.V3 Bottle Jack Instruction Manual on the Manualsnet website.

Yes, we have the Instruction Manual for Sealey AM20.V3 as well as other Sealey manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Instruction Manual should include all the details that are needed to use a Sealey AM20.V3. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Sealey AM20.V3 Bottle Jack Instruction Manual is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Sealey AM20.V3 Bottle Jack Instruction Manual consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Sealey AM20.V3 Bottle Jack Instruction Manual free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Sealey AM20.V3 Bottle Jack Instruction Manual, simply download the document to your computer. Once downloaded, open the PDF file and print the Sealey AM20.V3 Bottle Jack Instruction Manual as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.