Sealey VS7029 Bearing Instruction Manual PDF

1 of 3
1 of 3

Summary of Content for Sealey VS7029 Bearing Instruction Manual PDF

Thank you for purchasing a Sealey Product. Manufactured to a high standard this product will, if used according to these instructions and properly maintained, give you years of trouble free performance.

IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS AND CAUTIONS. USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.

INSTRUCTIONS FOR:

Front Wheel Bearing GEN2 Removal/Installation Kits Model No's: VS7027, VS7028, VS7029, VS7030

VS7027, VS7028, VS7029, VS7030 Issue No.1 - 02/08/12Original Language Version

1. CONTENTS

fig.1

Part Numbers

Item Description Qty VS7027 VS7028 VS7029 VS7030 1 Force Screw 1 VS7027.01 VS7028.01 VS7029.01 VS7030.01 2 Thrust Plate 1 VS7027.02 VS7028.02 VS7029.02 VS7030.02 3 Bearing Plate (Silver) 1 VS7027.03 VS7028.03 VS7029.03 VS7030.03 4 Bearing Plate (Black) 1 VS7027.04 VS7028.04 VS7029.04 VS7030.04

5 Sleeved Nut 1 VS7027.05 VS7028.05 VS7029.05 VS7030.05 6 Hub Guide Pins 5 VS7027.06 VS7028.06 VS7029.06 VS7030.06 7 Hub Clamp Screws 2 VS7027.07 VS7028.07 VS7029.07 VS7030.07 8 Hub Clamp (Black) 1pr VS7027.08 (62mm) VS7028.08 (66mm) VS7029.08 (72mm) VS7030.08 (78mm) 9 Hub Clamp (Silver) 1pr VS7027.09 (62mm) VS7028.09 (66mm) VS7029.09 (72mm) VS7030.09 (78mm)

2. APPLICATIONS

VS7027 VS7028 VS7029 VS7030 Audi Skoda Audi Ford

A2 1.2TDi PD (01-05) Fabia (00-12) A1 (2010 - on) C-Max (07-11) A2 (00-05) Focus ll (04-11)

VW VW Focus C-Max (03-07) Lupo 3L 1.2TDi PD (01-06) Fox (05-10) Seat

Polo (02-09) Cordoba (03-09) Mazda Ibiza (02-12) 3 (03-05)

Skoda Volvo Fabia (00-12) C30 (06-10)

Roomster (06-12) C70 (05-10) S40 (04-12)

VW V50 (04-10) Fox (05-10) Polo (02-12)

Jack Sealey Limited 2012

Original Language Version VS7027, VS7028, VS7029, VS7030 Issue No.1 - 02/08/12

3. SAFETY INSTRUCTIONS 3.1 General Safety WARNING! Ensure Health & Safety, local authority, and general workshop practice regulations are adhered to when using this tool. WARNING! Familiarise yourself with the specific applications and limitations of the kit, as well as any potential hazards. Ensure that the kit is correct for the task. Wear the appropriate personal protective equipment for the task. A full range is available from your Sealey dealer. DO NOT use a workshop press to fit GEN2 wheel bearings. DO NOT fit a wheel bearing with a damaged retaining ring. DO NOT use the kit for any purpose other than that for which it is designed. DO NOT use air tools with this kit to remove/install bearings. Always keep force screw well lubricated. Ensure that the vehicle is properly supported with axle stands before working under the vehicle. Ensure there is adequate lighting prior to using the kit. A range of inspection lamps are available from your Sealey dealer. Keep children and unauthorised persons away from the working area. DO NOT use the kit if any parts are damaged or missing, as this may cause failure and/or personal injury. DO NOT use the kit when you are tired, or under the influence of alcohol, drugs or intoxicating medication. After use, store in a safe, dry childproof area. s IMPORTANT: Always refer to the vehicle manufacturers service instructions, or a proprietary manual, to establish the current procedure and data. WARNING: The warnings, cautions and instructions in this manual cannot cover all possible conditions and situations that may occur. It must be understood that common sense and caution are factors which cannot be built into this product, but must be applied by the operator.

4. INTRODUCTION A selection of kits designed for the second generation of wheel bearing found on modern vehicles. These bearings are lightweight with an integral mounting flange. They are also pre-loaded with a retaining ring that secures the bearing into the housing. Each kit is individually designed to suit the relevant vehicle manufacturer. These kits can be used in-situ when replacing the front wheel bearing. Knowledge of the outer bearing diameter is required before selecting the appropriate kit, as some vehicles are fitted with more than one size of bearing.

fig.2

5. OPERATION 5.1 BearingRemoval(fig.2&fig.3) 5.1.1 Prepare the vehicle for the wheel bearing to be removed. Note: When GEN2 wheel bearings are removed, the retaining ring will sustain damage. DO NOT re-fit a bearing once it has been removed. 5.1.2 Fit the black hub clamp (8) behind the hub flange with the recessed side facing the hub carrier. Secure the hub clamp (8) with the hub clamp screws (7). 5.1.3 Fit the hub guide pins (6) into the thrust plate (2) so that the hub guide pins (6) align with the holes in the hub flange. Place the hub guide pins (6) though the holes in the hub flange so that they sit against the hub clamp (8) (fig.3). 5.1.4 Lubricate the force screw (1). 5.1.5 Fit the force screw (1) through the thrust plate (2) and through the bearing and hub carrier. 5.1.6 Place the black bearing plate (4) over the force screw (1) so that it sits on the outer race of the bearing.

Jack Sealey Limited 2012

Original Language Version VS7027, VS7028, VS7029, VS7030 Issue No.1 - 02/08/12

5.1.7 Screw the sleeved nut (5) over the force screw (1) so that it sits against the bearing plate (4). 5.1.8 Use a socket on the force screw (1) and a spanner on the sleeved nut (5) (fig.3). Draw the bearing from the hub carrier.

5.2 BearingInstallation(fig.4&fig.5) WARNING! DO NOT fit a bearing with a damaged retaining ring. Note: The bearing must only be subjected to force on the outer bearing race behind the retaining ring during installation. Using a workshop press on the hub flange to insert the bearing will cause premature failure or destroy the bearing during installation. 5.2.1 The silver hub clamp (9) sits in the space between the rear of the hub flange and the retaining ring (fig.5). Secure the hub clamp (9) with the hub clamp screws (7). 5.2.2 Fit the hub guide pins (6) into the thrust plate (2) so that the hub guide pins (6) align with the holes in the hub flange. Place the hub guide pins (6) though the holes in the hub flange so that they sit against the hub clamp (9). 5.2.3 Lubricate the force screw (1). 5.2.4 Offer the bearing and assembled kit to the hub carrier. Ensure that the bearing is sitting square to the hub carrier before commencing installation. 5.2.5 Fit the force screw (1) through the thrust plate (2) and through the bearing and hub carrier. 5.2.6 Place the silver bearing plate (3) over the force screw (1) so that it sits on the outer edge at the rear of the hub carrier. 5.2.7 Screw the sleeved nut (5) over the force screw (1) so that it sits against the bearing plate (3). 5.2.8 Use a socket on the force screw (1) and a spanner on the sleeved nut (5). Draw the bearing into the hub carrier. 5.2.9 When the bearing is correctly installed, the retaining ring will clip into the retaining groove.

fig.3

fig.4

fig.5

NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice. IMPORTANT: No liability is accepted for incorrect use of this product. WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim. INFORMATION: For a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode.

01284 757500

01284 703534 sales@sealey.co.uk

Sole UK Distributor, Sealey Group, Kempson Way, Suffolk Business Park, Bury St. Edmunds, Suffolk, IP32 7AR

www.sealey.co.uk Web

email

Parts support is available for this product. To obtain a parts list and diagram please log on to www.sealey.co.uk, email sales@sealey.co.uk or phone 01284 757500

ALWAYS KEEP FORCE SCREW WELL LUBRICATED. DO NOT USE AIR TOOLS

Manualsnet FAQs

If you want to find out how the VS7029 Sealey works, you can view and download the Sealey VS7029 Bearing Instruction Manual on the Manualsnet website.

Yes, we have the Instruction Manual for Sealey VS7029 as well as other Sealey manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Instruction Manual should include all the details that are needed to use a Sealey VS7029. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Sealey VS7029 Bearing Instruction Manual is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Sealey VS7029 Bearing Instruction Manual consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Sealey VS7029 Bearing Instruction Manual free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Sealey VS7029 Bearing Instruction Manual, simply download the document to your computer. Once downloaded, open the PDF file and print the Sealey VS7029 Bearing Instruction Manual as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.