Sealey VS7020.V3 Bearing Instruction Manual PDF

1 of 2
1 of 2

Summary of Content for Sealey VS7020.V3 Bearing Instruction Manual PDF

WARNING! Ensure all Health and Safety, local authority, and general workshop practice regulations are strictly adhered to when using tools. DO NOT use tools if damaged or worn. Maintain the tools in good and clean condition for best and safest performance. Ensure all threads are clean and well lubricated. Ensure vehicle is adequately supported with axle stands, ramps, etc. as appropriate. Wear suitable clothing to avoid snagging. DO NOT wear jewellery. Tie back long hair. Wear approved eye protection. A full range of personal safety equipment is available from your Sealey dealer. Account for all tools and parts being used and DO NOT leave them in or on the vehicle. IMPORTANT: Always refer to the vehicle manufacturers service instructions, or proprietary manual, to establish the correct procedure and data for the specific vehicle you are working on. These instructions for use are provided as a guide only.

INSTRUCTIONS FOR:

WHEEL BEARING REMOVAL / INSTALLATION KIT MODEL No: VS7020.V3

Comprehensive kit of tools for the fast and effective removal and Installation of wheel bearings on front-wheel drive vehicles. Reduces chances of damage to hub and bearing. Heavy-duty steel drifts with phosphate coating to prevent corrosion. Heavyweight drive screw for use with impact tools. Also suitable for removing and installing large industrial bearings. Supplied in carry-case.

Model No: VS7020.V3 Drift Sizes : 55, 60, 64, 67, 73, 75, 78, 82, 84, 88mm

End Cap : 50mm

Sleeve External: 76, 86, 92, 101mm

Hub screw length: 210mm

Hub screw drive: 32, 38mm

IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble free performance.

1. SAFETY

2. INTRODUCTION

3. SPECIFICATIONS

Refer to instruction

manual

Wear eye protection

VS7020.V3 Issue: 2(I) - 16/12/15Original Language Version Jack Sealey Limited

4. CONTENTS

NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice. IMPORTANT: No liability is accepted for incorrect use of this product. WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.

01284 757500

01284 703534 sales@sealey.co.uk

Sole UK Distributor, Sealey Group, Kempson Way, Suffolk Business Park, Bury St. Edmunds, Suffolk, IP32 7AR

www.sealey.co.uk

Parts support is available for this product. To obtain a parts listing and/or diagram, please log on to www.sealey.co.uk, email sales@sealey.co.uk or telephone 01284 757500.

Environmental Protection Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted,

taken to a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely unserviceable and requires disposal, dispose of the product according to local regulations.

BEARING REMOVAL: Identify the correct sleeve (6) to sit on the outside of the bearing housing and the correct drift (3) to drive the bearing from the housing. Assemble as shown in fig.1A using the correct sleeve cap (7). Keep the hub screw and nut well lubricated whilst driving out the bearing.

BEARING INSTALLATION: Identify the correct sleeve cap (7) to sit on the outside of the bearing housing and the correct diameter drift (3) to drive the new bearing into the housing. Assemble as shown in fig.1B. Keep the hub screw and nut well lubricated whilst driving the new bearing into the housing. The 50mm end cap is used to locate into the back of the drifts; they can then be used in a workshop press when it is not possible to use the hub screw.

5. OPERATION

fig.1

1. HUB SCREW NUT 5. VEHICLE

Manualsnet FAQs

If you want to find out how the VS7020.V3 Sealey works, you can view and download the Sealey VS7020.V3 Bearing Instruction Manual on the Manualsnet website.

Yes, we have the Instruction Manual for Sealey VS7020.V3 as well as other Sealey manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Instruction Manual should include all the details that are needed to use a Sealey VS7020.V3. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Sealey VS7020.V3 Bearing Instruction Manual is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Sealey VS7020.V3 Bearing Instruction Manual consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Sealey VS7020.V3 Bearing Instruction Manual free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Sealey VS7020.V3 Bearing Instruction Manual, simply download the document to your computer. Once downloaded, open the PDF file and print the Sealey VS7020.V3 Bearing Instruction Manual as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.