Sealey TC966 Bead Breaker Instruction Manual PDF

1 of 3
1 of 3

Summary of Content for Sealey TC966 Bead Breaker Instruction Manual PDF

1. SAFETY 1.1. General Safety

WARNING! Ensure Health & Safety, local authority, and general workshop practice regulations are adhered to when using this equipment. Under Health and Safety Law, Employers and Self Employed Personnel have a legal duty to ensure Safe Working

Conditions for all employees and personnel that may come into contact with this equipment. In particular they must carry out a specific risk and hazard assessment in the workplace to eliminate or reduce any risk found and must record, update and retain records of the results of this inspection. 1.1.1. Familiarise yourself with the applications, limitations and any possible or potential hazards of the Bead Breaker. 1.1.2. Maintain theBead Breaker in good condition (use an authorised service agent).

WARNING! Check regularly for damaged parts. Any part that is damaged must be repaired or replaced before the equipment is next used.

1.1.3. Use the Bead Breaker in a suitable work area, keep area clean and tidy and free from unrelated materials. Ensure that there is adequate lighting.

1.1.4. Keep the Bead Breaker clean for best and safest performance. 1.1.5. Wear approved safety eye protection. 1.1.6. Keep hands well clear of the bead breaker. 1.1.7. Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip safety shoes. 1.1.8. Remove ill fitting clothing. Remove ties, watches, rings other loose jewellery and contain and/or tie back long hair. 1.1.9. Keep hands away from pinch and crush points that can be created during operation. 1.1.10. Keep children and unauthorised persons away from the work area.

WARNING! DO NOT use on split, multi-piece or rims greater than 26. 8 DO NOT use the Bead Breaker for any purpose other than that for which it is designed. 8 DO NOT operate the Bead Breaker if any parts are damaged or missing as this may cause failure and/or personal injury. 8 DO NOT allow untrained persons to operate the Bead Breaker. 8 DO NOT operate the Bead Breaker when you are tired or under the influence of alcohol, drugs or intoxicating medication. 8 DO NOT top up system with brake fluid. Use hydraulic oil only. 8 DO NOT adjust the safety overload valve. WARNING! The warnings, cautions and instructions referred to in this manual cannot cover all possible conditions and situations that

may occur. It must be understood that common sense and caution are factors which cannot be built into this product, but must be applied by the operator.

2. INTRODUCTION Hydraulic Bead Breaker, suitable for breaking beads on commercial and agricultural tyres. Use in conjunction with hydraulic pump and hose (not included).

HYDRAULIC BEAD BREAKER MODEL NO: TC966

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions and properly maintained, give you years of trouble free performance.

IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.

Refer to Instruction

Manual

Wear Eye Protection

Wear Protective Gloves

Wear Safety Footwear

TC966 Issue: 3(HF) - 16/05/18Original Language Version Jack Sealey Limited

3. SPECIFICATIONS

4. OPERATION WARNING! The tyre must be deflated before using the bead breaker. Failure to heed this warning, could result in injury. WARNING! DO NOT use on split, multi-piece or rims greater than 26.

4.1. Connect the bead breaker to your pump. You may use either a manual pump (RE97.10-01) or a air hydraulic pump (RE83/840). 4.1.1. Note:-The manual pump may need to be operated by a second person to allow the operator to keep both hands on the bead breaker. 4.1.2. Note:-The foot operated air hydraulic pump will enable you to maintain greater control over the bead breaker. If using an air pump you will

require an air supply of 100 - 120psi. 4.1.3. Note:-Whichever pump you use, refer to the manufacturers instructions supplied with that pump for correct connection and usage. 4.2. Remove valve core and all balance weights. 4.3. Hold the breaker to the rim as shown in fig.1. 4.4. Operate the pump. With the claw pushing against the

outer part of the rim, the shovel and feet push against the bead of the tyre and the inner rim.

4.5. Maintaining the pump pressure, the shovel pushes against the tyre and breaks the bead from the wheel rim. When the bead is broken release the pump pressure and remove the bead breaker from the rim.

4.6. Repeat this operation around the wheel as many times as necessary to break the tyre bead all the way around the wheel.

4.7. Repeat steps 4.3 to 4.6 on the opposite side of the wheel.

RE97.10-01

fig.1

Option 1. (Optional Hydraulics) Part No.

Air Hydraulic Pump 10 tonne RE83/840

Hose Assembly RE97.10-03

Option 2. (Optional Hydraulics) Part No.

Pump Assembly RE97.10-01

Hose Assembly RE97.10-03

RE97.10-03

RE83/840

TC966 Issue: 3(HF) - 16/05/18Original Language Version Jack Sealey Limited

5. MAINTENANCE WARNING Only fully qualified personnel should attempt maintenance or repair.

5.1. When not in use, ensure jaw remains in the open position to minimise corrosion on the ram piston. 5.2. Keep the bead breaker clean and lubricate all moving parts on a regular basis.

WARNING DO NOT use brake fluid as this may cause serious damage to the jack and will invalidate the warranty! Only use a good quality jack oil, such as SEALEY HYDRAULIC JACK OIL. NOTE: Ensure waste oil is disposed of in accordance with local authority regulations.

5.3. Before each use check for broken, cracked, bent, or loose parts, or any visible damage to welds, ram, pump, jaws, frame and all parts including nuts, bolts, pins and other fasteners. If any suspect item is found, remove from service and take necessary action to remedy the problem.

8 DO NOT use the bead breaker if believed to have been subjected to abnormal load or shock. Inspect and take appropriate action. IMPORTANT: NO RESPONSIBILITY IS ACCEPTED FOR INCORRECT USE OF THE MACHINE. Hydraulic products are only repaired by local service agents. We have service/repair agents in all parts of the UK.

8 DO NOT return to Sealey. Please telephone Sealey on 01284 757500 to obtain the address and phone number of your local agent. If breaker is under guarantee please contact your dealer.

De-commissioning the bead breaker Should the bead breaker become completely unserviceable and require disposal, draw off the oil into an approved container and dispose of the jack and the oil according to local regulations.

6. TROUBLESHOOTING

Symptom Possible Causes Corrective Action Claw or shovel erratic. External leakage.

Binding sticking or components. Contact Sealey dealer for service. Clean and lubricate all moving parts.

System is pressurised but the bead breaker is not responding.

Loose or faulty hydraulic connections/couplers.

Oil level in pump is low. Pump not operating.

Depressurise Tighten/replace connections/couplers. Depressurise and fill the pump. Consult pump instruction manual.

Claw will not close or shovel will not fully extend or withdraw.

Oil in pump is low. Sticking rams or binding components.

Depressurise and fill the pump. Contact Sealey dealer for service.

Bead breaker will not maintain pressure. Pump malfunctioning. Seals leaking.

Consult pump instruction manual. Contact Sealey dealer for service.

Oil leaking. Worn seals. Contact Sealey dealer for service.

Bead breaker will not open and/or shovel stuck or slower than normal.

Faulty coupler.

Pump reservoir over filled.

Internal damage. Linkage binding.

Depressurise Tighten/replace connections/couplers. Depressurise and drain fluid to correct level. Contact Sealey dealer for service. Clean and lubricate all moving parts.

Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR 01284 757500 01284 703534 sales@sealey.co.uk www.sealey.co.uk

ENVIRONMENT PROTECTION Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids according to local regulations.

Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice. Important: No Liability is accepted for incorrect use of this product. Warranty: Guarantee is 12 months from purchase date, proof of

Manualsnet FAQs

If you want to find out how the TC966 Sealey works, you can view and download the Sealey TC966 Bead Breaker Instruction Manual on the Manualsnet website.

Yes, we have the Instruction Manual for Sealey TC966 as well as other Sealey manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Instruction Manual should include all the details that are needed to use a Sealey TC966. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Sealey TC966 Bead Breaker Instruction Manual is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Sealey TC966 Bead Breaker Instruction Manual consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Sealey TC966 Bead Breaker Instruction Manual free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Sealey TC966 Bead Breaker Instruction Manual, simply download the document to your computer. Once downloaded, open the PDF file and print the Sealey TC966 Bead Breaker Instruction Manual as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.