Sealey WB954LED Beacon Instruction Manual PDF

1 of 2
1 of 2

Summary of Content for Sealey WB954LED Beacon Instruction Manual PDF

Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions and properly maintained, give you years of trouble free performance.

1. SAFETY INSTRUCTIONS

IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS AND CAUTIONS. USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE OR PERSONAL INJURY, AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.

1.1 GENERAL SAFETY Familiarise yourself with this product's application and limitations, as well as any specific potential hazards peculiar to the beacon. Replace or repair damaged parts. Use recommended parts only. Non authorised parts may be dangerous and will invalidate the warranty. DO NOT use the beacon for any purpose other than for which it is designed. DO NOT allow children to operate the beacon. DO NOT operate the beacon if any parts are missing or damaged as this may cause failure or possible personal injury. When not in use switch the beacon off and where appropriate remove plug from power supply.

2. TECHNICAL SPECIFICATIONS Voltage:...................................................................................12V-24V dc Current:.......................................................................................... 450mA Number of LEDs: .................................................................................. 40 Index of protection (EN 60598-1): ..................................................... IP56 Operating Temperature:....................................................-30C to +50C Radio Interference Filter:.......................... ......... EC95/54 EMC approved Approvals:......................................................................................ECE65

3 . INTRODUCTION

Model Nos: WB951LED,WB952LED,WB953LED,WB954LED,WB955LED

INSTRuCTIONS FOR:

LED WARNING BEACONS 12/24Volt VARIOUS FITTINGS

Heavy-duty ABS bases. Quick release uV stabilised domes will not fade when exposed to sunlight. Features 40 LEDs for an increased output of light. 3-Function control allows for different LED configuration depending on operation. CE Approved and E-Marked.

WB951LED

128mm Overall height: 200mm Length of mounting: 40mm

WB952LED

140mm Height: 190mm

WB953LED

128mm Height: 200mm

WB955LED

128mm Height: 250mm

140mm Height: 170mm WB954LED

WB951LED,WB951LED,WB953LED, WB954LED,WB955LED

ISSuE: 1 12/12/13 Original Language Version Jack Sealey Limited

Environmental Protection. Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to a recycling centre and disposed of in a manner which is compatible with the environment.

4. FIxING INSTRUCTIONS 4.1 WB951LED: 12mm Single Bolt Fixing 4.1.1. Drill a 13mm mounting hole in a suitable point on the vehicle. 4.1.2. Connect to cables of at least 2mm section and use an 8A fuse; check polarities. 4.1.3. Fix the beacon by using nuts and washers according to the type and shape of the mounting surface

4.2 WB952LED: Three Bolt Fixing Base 4.2.1. Drill mounting holes using the beacon base as a template. Also make provision to route cables into the vehicle. 4.2.2. Connect to cables of at least 2mm section and use an8A fuse; check polarities. 4.2.3. Fix the beacon with 3 x M6 screws.

4.3 WB953LED: Fixed Spigot Base UseinconnectionwithDINspigot (a range of DIN mountings is available: please see Sealey catalogue). DINadaptormountstovehicleallowingremoval/installationwithouttools. Suitableforsituationswheresecurityisaproblem. 4.3.1. Fit a suitable adapter socket onto the vehicle. Make sure it is perfectly vertical. 4.3.2. use cables of at least 2mm section and use an 8A fuse; check polarities. 4.3.3. Push the beacon spigot down fully onto the adapter socket and secure by tightening the wing nut. 4.3.4. When the beacon is removed, always close the adapter socket outlet using the rubber cap.

4.4 WB954LED: Magnetic Base Fittedwithhighpowermagnetstrongenoughtocopewithnormalroadspeeds. Suppliedwith3mtrcoiledflexanduniversalauxiliarypoweroutletplug. 4.4.1. The beacon must be placed on a surface parallel to the ground. 3.4.2. The surface should be flat and clean to ensure good adherence.

4.5 WB955LED: Flexible Base with DIN Spigot Mounting. 4.5.1. Fit a suitable adapter socket onto the vehicle. Make sure it is perfectly vertical. 4.5.2. use cables of at least 2mm section and use an 8A fuse; check polarities. 4.5.3. Push the beacon spigot down fully onto the adapter socket and secure by tightening the wing nut. 4.5.4. When the beacon is removed, always close the adapter socket outlet using the rubber cap.

The beacons will switch between 12V and 24V automatically.

6.1. Three flash patterns are available by selecting one of the three switch positions as in fig.2. The switch is accessed by removing the dome as in fig.1. 6.2. Switch 1: Rotating flash; flash rotates mimicking a rotary beacon. Switch 2: Six rapid flashes followed by a break. Switch 3: Two flashes followed by a break.

NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice. IMPORTANT: No responsibility is accepted for incorrect use of this equipment. WARRANTY: Guarantee is 12 months from purchase date. Proof of purchase will be required for any claim. INFORMATION: Please call us for a copy of our latest catalogue on 01284 757525, leaving your name, address and postcode.

Sole UK Distributor, Sealey Group, Kempson Way, Suffolk Business Park, Bury St. Edmunds, Suffolk, IP32 7AR

01284 757500

01284 703534 sales@sealey.co.uk

www.sealey.co.uk

6. FLASH PATTERN SELECTION

5. VOLTAGE SELECTION

fig.1 fig.2

WEEE Regulations. Dispose of this product at the end of its working life in compliance with the Eu Directive on Waste Electrical and Electronic Equipment. When the produ

Manualsnet FAQs

If you want to find out how the WB954LED Sealey works, you can view and download the Sealey WB954LED Beacon Instruction Manual on the Manualsnet website.

Yes, we have the Instruction Manual for Sealey WB954LED as well as other Sealey manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Instruction Manual should include all the details that are needed to use a Sealey WB954LED. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Sealey WB954LED Beacon Instruction Manual is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Sealey WB954LED Beacon Instruction Manual consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Sealey WB954LED Beacon Instruction Manual free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Sealey WB954LED Beacon Instruction Manual, simply download the document to your computer. Once downloaded, open the PDF file and print the Sealey WB954LED Beacon Instruction Manual as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.