- Manuals
- Brands
- Samsung
- Microwave
- MC17T8000C
- Installation Guide
Samsung MC17T8000C Microwave Installation Guide PDF
Summary of Content for Samsung MC17T8000C Microwave Installation Guide PDF
Installation Instructions Over The Range Microwave Oven
BEFORE YOU BEGIN (Read these instructions completely and carefully.)
IMPORTANT Save these instructions for local inspectors use.
IMPORTANT Observe all governing codes and ordinances.
Note to Installer - Be sure to leave these instructions with the Consumer. Note to Consumer - Keep these instructions for future reference. Skill level - Installation of this appliance requires basic mechanical and electrical skills. Proper installation is the responsibility of the installer. Product failure due to improper installation is not covered under the Warranty.
READ CAREFULLY. KEEP THESE INSTRUCTIONS.
MC17T8000CS_AA_DE68-04129D-01_EN.indd 1 2021-03-25 11:25:53
2
Contents
1. Placement of the mounting plate . . . . . . 8
A. Removing the microwave oven from the carton/Removing the mounting plate. . . . 8
B. Finding the wall studs . . . . . . . . . . . . . . . . 8
C. Determining wall plate location under your cabinet . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
D. Aligning the wall plate. . . . . . . . . . . . . . . 10
2. Ventilation types (choose a, b or c) . . . 11
A. Outside top exhaust (vertical duct) . . . . 12
A1. Installation procedure for the exhaust adaptor and proper damper operation check . . . . . . . . . . . . . . . . . . . . . . . . . . 12
A2. Adjust the exhaust adaptor . . . . . . . . 12
B. Recirculating (non-vented ductless). . . . 12
B1. Adapting the microwave blower for recirculation . . . . . . . . . . . . . . . . . . . . . 12
B2. Installing the charcoal filter. . . . . . . . . 13
C. Outside back exhaust (horizontal duct) . 14
C1. Adapting the microwave blower for outside back exhaust . . . . . . . . . . . . . 14
3. Installation . . . . . . . . . . . . . . . . . . . . . . . 15
A. Preparing the rear wall for outside back exhaust . . . . . . . . . . . . . . . . . . . . . . . . . . 15
B. Attach the mounting plate to the wall . . 15
C. Use the top cabinet template to prepare the top cabinet. . . . . . . . . . . . . . . . . . . . . . . . 16
D. Mount the microwave oven . . . . . . . . . . 16
E. Connecting ductwork for outside top exhaust . . . . . . . . . . . . . . . . . . . . . . . . . . 17
4. Before you use your microwave . . . . . 18
Step-by-step installation guide
Important safety instructions . . . . . . . . . . . 3
Electrical requirements . . . . . . . . . . . . . . . . 3
Hood exhaust . . . . . . . . . . . . . . . . . . . . . . . . 4
Damage - Shipment/Installation . . . . . . . . 6
Parts included . . . . . . . . . . . . . . . . . . . . . . . 6
Tools you will need . . . . . . . . . . . . . . . . . . . 7
Mounting space . . . . . . . . . . . . . . . . . . . . . . 7
General information
MC17T8000CS_AA_DE68-04129D-01_EN.indd 2 2021-03-25 11:25:53
3
General information
IMPORTANT SAFETY INSTRUCTIONS
This product requires a three-prong grounded outlet. The installer must perform a ground continuity check on the power outlet box before beginning the installation to insure that the outlet box is properly grounded. If not properly grounded, or if the outlet box does not meet electrical requirements noted (under ELECTRICAL REQUIREMENTS), a qualified electrician should be employed to correct any deficiencies.
Insure proper ground exists before use
CAUTION: For personal safety, remove house fuse or open circuit breaker before beginning installation to avoid severe or fatal shock injury.
CAUTION: For personal safety, the mounting surface must be capable of supporting the cabinet load and the added weight of this 69 pound product, plus additional oven loads of up to 50 pounds or a total weight of 109 pounds.
CAUTION: For personal safety, this product cannot be installed in cabinet arrangements such as an island or a peninsula. It must be mounted to BOTH a top cabinet AND a wall.
NOTE: For easier installation and personal safety, it is recommended that two people install this product.
IMPORTANT PLEASE READ CAREFULLY. FOR PERSONAL SAFETY, THIS APPLIANCE MUST BE PROPERLY GROUNDED TO AVOID SEVERE OR FATAL SHOCK.
Insure proper ground exists before use
Insure proper ground exists before use.
The power cord of this appliance is equipped with a three-prong (grounding) plug which mates with a standard three-prong (grounding) wall receptacle to minimize the possibility of electric shock hazard from this appliance.
You should have the wall receptacle and circuit checked by a qualified electrician to make sure the receptacle is properly grounded.
If you have a standard two-prong wall receptacle, it is very important to have it replaced with a properly grounded three-prong wall receptacle, installed by a qualified electrician.
DO NOT, UNDER ANY CIRCUMSTANCES, CUT, DEFORM OR REMOVE ANY OF THE PRONGS FROM THE POWER CORD. DO NOT USE WITH AN EXTENSION CORD.
ELECTRICAL REQUIREMENTS Product rating is 120 volts AC, 60 Hertz, 14.6 amps and 1.75 kilowatts.This product must be connected to a supply circuit of the proper voltage and frequency. Wire size must conform to the requirements of the National Electrical Code or the prevailing local code for this kilowatt rating. The power supply cord and plug should be brought to a separate branch circuit single grounded outlet of at least 15 A and max of 20 A. The outlet box should be located in the cabinet above the microwave oven. The outlet box and supply circuit should be installed by a qualified electrician and conform to the National Electrical Code or the prevailing local code.
MC17T8000CS_AA_DE68-04129D-01_EN.indd 3 2021-03-25 11:25:53
4
General information
NOTE: Read these next two pages only if you plan to vent your exhaust to the outside. If you plan to recirculate the air back into the room, proceed to page 11.
OUTSIDE TOP EXHAUST (EXAMPLE ONLY) The following chart contains an example of one possible ductwork installation.
DUCT PIECES EQUIVALENT LENGTH x NUMBER USED = EQUIVALENT
LENGTH
Roof Cap 24 ft. x (1) = 24 ft.
12 Ft. Straight Duct (6 Round) 12 ft. x (1) = 12 ft.
Rectangular-to-Round Transition Adaptor* 5 ft. x (1) = 5 ft.
Equivalent lengths of duct pieces are based on actual tests and reflect requirements for good venting performance with any vent hood.
Total Length = 41 ft.
* IMPORTANT: If a rectangular-to-round transition adaptor is used, the bottom corners of the damper will have to be cut to fit, using the tin snips, in order to allow free movement of the damper.
OUTSIDE BACK EXHAUST (EXAMPLE ONLY) The following chart contains an example of one possible ductwork installation.
DUCT PIECES EQUIVALENT LENGTH x NUMBER USED = EQUIVALENT
LENGTH
Wall Cap 40 ft. x (1) = 40 ft.
3 Ft. Straight Duct (3 x 10 Rectangular) 3 ft. x (1) = 3 ft.
90 Elbow 10 ft. x (2) = 20 ft.
Equivalent lengths of duct pieces are based on actual tests and reflect requirements for good venting performance with any vent hood.
Total Length = 63 ft.
NOTE: For back exhaust, care should be taken to align the exhaust with the space between studs, or the wall should be prepared at the time it is constructed by leaving enough space between the wall studs to accommodate the exhaust duct.
HOOD EXHAUST
MC17T8000CS_AA_DE68-04129D-01_EN.indd 4 2021-03-25 11:25:53
5
General information
Outside ventilation requires a HOOD EXHAUST DUCT. Read the following carefully.
NOTE: It is important that venting be installed using the most direct route and with as few elbows as possible. This ensures clear venting of exhaust and helps prevent blockages. Also, make sure dampers swing freely and nothing is blocking the ducts.
Exhaust connection: The hood exhaust has been designed to mate with a standard 3 x 10 rectangular duct.
If a round duct is required, a rectangular-to-round transition adaptor must be used. Do not use less than a 6 diameter duct.
Maximum duct length: For satisfactory air movement, the total duct length of 3 x 10 rectangular or 6 diameter round duct should not exceed 140 equivalent feet.
Elbows, transitions, wall and roof caps, etc., present additional resistance to airflow and are equivalent to a section of straight duct which is longer than their actual physical size. When calculating the total duct length, add the equivalent lengths of all transitions and adaptors plus the length of all straight duct sections. The chart below shows you how to calculate total equivalent ductwork length using the equivalent length in feet of some typical ducts.
DUCT PIECES EQUIVALENT LENGTH x NUMBER USED = EQUIVALENT
LENGTH
Rectangular-to-Round Transition Adaptor* 5 ft. x ( ) = ft.
Wall Cap 40 ft. x ( ) = ft.
90 Elbow 10 ft. x ( ) = ft.
45 Elbow 5 ft. x ( ) = ft.
90 Elbow 25 ft. x ( ) = ft.
45 Elbow 5 ft. x ( ) = ft.
Roof Cap 24 ft. x ( ) = ft.
Straight Duct 6 Round or 3 x 10 Rectangular 1 ft. x ( ) = ft.
Total Ductwork = ft.
* IMPORTANT: If a rectangular-to-round transition adaptor is used, the bottom corners of the damper will have to be cut to fit, using tin snips, in order to allow free movement of the damper.
Equivalent lengths of duct pieces are based on actual tests and reflect the requirements for good venting performance with any vent hood.
MC17T8000CS_AA_DE68-04129D-01_EN.indd 5 2021-03-25 11:25:53
6
General information
If the unit is damaged in shipment, return the unit to the store in which it was bought for repair or replacement. If the unit is damaged by the customer, repair or replacement is the responsibility of the customer. If the unit is damaged by the installer (if other than the customer), repair or replacement must be made by
arrangement between the customer and installer.
DAMAGE - SHIPMENT/INSTALLATION
HARDWARE PACKET
PART QUANTITY
Template
INSTALLATION
INSTRUCTIONS
Wood Screws ( x 2) 1
Template
INSTALLATION
INSTRUCTIONS
Toggle Bolts (and wing nuts) (3/16 x 3)
3
Template
INSTALLATI
INSTRUCTI
Self-aligning Machine Screws ( - 28 x 3 ) 3
You will find the installation hardware contained in a packet with the unit. Check to make sure you have all these parts.
NOTE: Some extra parts are included.
ADDITIONAL PARTS
PART QUANTITY
TOP CABINET TEMPLATE
REAR WALL TEMPLATE
Top Cabinet Template 1 TOP CABINET TEMPLATE
REAR WALL TEMPLATE Rear Wall Template 1
Installation Instructions 1
Template
INSTALLATION
INSTRUCTIONS
Exhaust adaptor 1
GREASE FILTER You can find the grease filter that is installed on the product or just packed with the product. Please check the shape of your grease filter and install the grease filter on your product correctly.
PART QUANTITY
Separately Packed Grease Filters 2
PARTS INCLUDED
MC17T8000CS_AA_DE68-04129D-01_EN.indd 6 2021-03-25 11:25:53
7
General information
#1 and #2 Phillips screwdriver
Pencil Ruler or tape measure and straight edge
Carpenter square (optional)
Tin snips (for cutting damper,
if required)
Scissors (to cut template,
if necessary)
Electric drill with 3/16, and drill bits
Filler blocks or scrap wood pieces, if needed for top cabinet spacing (used on recessed bottom cabinet
installations only)
Gloves Saw (saber, hole or keyhole) Stud finder or Hammer (optional)
Safety goggles
Level Duct and masking tape
TOOLS YOU WILL NEED
16 30
5
30 min.
Bottom edge of the cabinet needs to be 30 or more from the cooking surface.
Backsplash
12 max. NOTES: The space between the cabinets must be 30 wide and
free of obstructions. This microwave oven is for installation over ranges up
to 36 wide. If you are going to vent your microwave oven to the
outside, see the Hood Exhaust Section for exhaust duct preparation.
If installing the microwave oven beneath smooth flat cabinets, be careful to follow the instructions on the top cabinet template for power cord clearance.
Maximum cabinet depth above and beside the unit is 12.
The dimensions provided are the minimum required for mounting the microwave oven. Local codes and the practical use of the range will likely require you to provide more than the 13.5 shown between the range and the bottom of the microwave.
MOUNTING SPACE
MC17T8000CS_AA_DE68-04129D-01_EN.indd 7 2021-03-25 11:25:54
8
Step-by-step installation guide
1. PLACEMENT OF THE MOUNTING PLATE
A. REMOVING THE MICROWAVE OVEN FROM THE CARTON/REMOVING THE MOUNTING PLATE
1. Remove the installation instructions, Exhaust adaptor, filters, glass tray, and the small hardware bag. Do not remove the Styrofoam protecting the front of the oven.
2. Fold back all 4 carton flaps fully against carton sides. Then carefully roll the oven and carton over onto the top side. The oven should be resting in the Styrofoam.
Styrofoam
Cartonrton
Styrofoam
3. Pull the carton up and off the oven. 4. Remove and properly discard plastic bags.
Screws Screws
Mounting Plate Scr
Mou ti g Plate
Scre
5. Remove the 2 screws from the mounting plate. This plate will be used as the rear wall template and for mounting.
6. Replace the two screws you removed and carefully screw them back into the case. DO NOT OVER- TIGHTEN. If you over-tighten the screws, you can strip the screws and damage the case.
B. FINDING THE WALL STUDS
Wall Studs
CenterCenter
Wall ds
1. Find the studs using one of the following methods: A. Stud findera magnetic device which locates nails.
OR
B. Use a hammer to tap lightly across the mounting surface to find a solid sound. This will indicate a stud location.
2. After locating the stud(s), find the studs center by probing the wall with a small nail to find the edges of the stud. Then, place a mark halfway between the edges. The center of any adjacent studs should be 16 or 24 from this mark.
3. Draw a line down the center of the studs. THE MICROWAVE MUST BE CONNECTED TO AT LEAST ONE WALL STUD.
MC17T8000CS_AA_DE68-04129D-01_EN.indd 8 2021-03-25 11:25:54
9
Step-by-step installation guide
C. DETERMINING WALL PLATE LOCATION UNDER YOUR CABINET
Plate position beneath flat bottom cabinet.
CL
16
At least 30
Draw a vertical line on the wall at the center of the 30 wide space. Tape the Rear Wall Template onto the wall so that the top of the template touches the bottom of the cabinet and the centerline on the template lines up with the line you drew on the wall.
Plate position beneath recessed bottom cabinet with front overhang.
CL
Plate position beneath recessed bottom cabinet with front overhang
Draw a line on the back wall equal to the depth of the front overhang.
30" to Cooktop30 to Cooktop
Draw a horizontal line to mark how far the inside of the front overhang descends below the cabinet.
Plate position beneath framed recessed cabinet bottom.
CL 30 to Cooktop
Draw a vertical line on the wall at the center of the 30 wide space. Tape the Rear Wall Template onto the wall so that the top of the template touches the bottom of the cabinet frame and the centerline on the template lines up with the line you drew on the wall.
Your cabinets may have decorative trim that interferes with the microwave installation. Remove the decorative trim to install the microwave properly and to make it level.
THE MICROWAVE MUST BE LEVEL.
Use a level to make sure the cabinet bottom is level.
Draw a vertical line on the wall at the center of the 30 wide space. Draw a second, horizontal line on the wall below the cabinet to mark how far the inside of the front overhang descends below the cabinet. Tape the Rear Wall Template onto the wall so that the top of the template touches the bottom of the horizontal line and the centerline on the template lines up with the vertical line.
MC17T8000CS_AA_DE68-04129D-01_EN.indd 9 2021-03-25 11:25:54
10
Step-by-step installation guide
D. ALIGNING THE WALL PLATE
CL
CAUTION: Wear gloves to avoid cutting fingers on sharp edges.
Area E Hole C
Hole B
Hole A Centerline notches
Draw a Vertical Line on Wall from Center of Top Cabinet
Draw a Horizontal line on wall from bottom of Rear Wall Template.
Horizontal LineHorizontal Line
Draw a Horizontal line on wall from bottom of Rear Wall Template.
Draw a Horizontal line on the wall along the botto of Rear Wall Template.
ri t l LineHorizontal Line Area
Centerli notches
l
Hol l
CAUTION: Wear glov to avoid cutting fingers on sharp edges.
1. Draw a Horizontal line on the wall at the bottom of the Rear Wall Template.
2. Drill holes for toggle bolts in 3 locations (Hole A, Hole B, Hole C) as shown in the illustration above. If the location of a hole lines up with a stud, drill a 3/16 hole for a wood screw. You cannot use a toggle bolt to attach the wall plate to a stud.
NOTE: DO NOT MOUNT THE PLATE AT THIS TIME.
3. Holes A, B and C are inside area E. If none of these holes line up with a stud, find a stud in area E that lines up with a hole circle in Area E, and then drill a 3/16 hole into it for a wood screw. You must have at least one wood screw mounted firmly into a stud to support the weight of the microwave. Set the mounting plate aside.
MC17T8000CS_AA_DE68-04129D-01_EN.indd 10 2021-03-25 11:25:54
11
Step-by-step installation guide
2. VENTILATION TYPES (CHOOSE A, B OR C)
This microwave oven is compatible with the following three types of ventilation:
A. Outside Top Exhaust (Vertical Duct) B. Recirculating (Non-Vented Ductless) C. Outside Back Exhaust (Horizontal Duct)
NOTE: This microwave is shipped assembled for Outside Top Exhaust (except for non-vented models). An exhaust adaptor is shipped assembled and attached to the filler- upper. Select the type of ventilation required for your installation and proceed to that section.
A. OUTSIDE TOP EXHAUST (VERTICAL DUCT)
B. RECIRCULATING (NON-VENTED DUCTLESS)
Adaptor in Place for Outside Top Exhaust
Adaptor in Place for Outside Top Exhaust
See page 12 See page 12
A Charcoal Filter Accessory Kit is required for the nonvented exhaust. (See your Owners Manual for the kit number.)
C. OUTSIDE BACK EXHAUST (HORIZONTAL DUCT)
See page 14
MC17T8000CS_AA_DE68-04129D-01_EN.indd 11 2021-03-25 11:25:54
12
Step-by-step installation guide
A. OUTSIDE TOP EXHAUST (VERTICAL DUCT)
A1. INSTALLATION PROCEDURE FOR THE EXHAUST ADAPTOR AND PROPER DAMPER OPERATION CHECK
Blower Plate
Damper
Exhaust Adaptor
Retaining Hooks Back of Microwave Oven
1. Slide the exhaust adaptor as shown in the diagram above.
2. Make sure the tape securing the damper is removed and damper pivots easily before you mount the microwave.
CAUTION: You will need to make adjustments to assure proper alignment with your house exhaust duct after the microwave is installed.
A2. ADJUST THE EXHAUST ADAPTOR
After you have installed the microwave, you will need to open the top cabinet and adjust the exhaust adaptor so that you can connect it to the house duct.
Damper
For Side-toSide Adjustment, Slide the Exhaust Adaptor as Needed
Back of Microwave Oven
NOTE: When mounting the microwave oven, be careful of the damper not be damaged by wall or cabinet.
NOTE: You must attach the house duct to the exhaust adaptor after installation is complete.
House DuctHouse ct
B. RECIRCULATING (NON-VENTED DUCTLESS)
B1. ADAPTING THE MICROWAVE BLOWER FOR RECIRCULATION
1. Remove and save screw that holds blower plate to microwave.
2. Lift up the blower plate.
Back of Microwave Oven
Blower Retaining Screws
NOTE: The exhaust adaptor with the damper is not needed for recirculating models. You may want to save them for possible future use.
MC17T8000CS_AA_DE68-04129D-01_EN.indd 12 2021-03-25 11:25:55
13
Step-by-step installation guide
3. Remove the screw that holds the blower motor and carefully pull out the blower unit. The wires will extend far enough to allow you to adjust the blower unit.
CAUTION: To avoid breaking or cracking the blower blade, do not touch the blade. Hold the outer case of the blower when you pull it out or put it back in place.
4. Roll the blower unit 90 so that the fan blade openings are facing toward the front of the microwave.
Before Roll After Roll
5. Place the blower unit back into the opening.
CAUTION: Do not pull or stretch the blower unit wiring. Make sure the wires are not pinched.
6. Remove the metal vent fan cover on the back of the microwave by sliding it up.
7. Close the blower door. Slide blower shield onto the top of the blower door opening.
8. Secure the blower to the microwave using the blower retaining screws from Step 1.
Back of Microwave Oven
Blower Retaining Screws
Blower Retaining Screw
B2. INSTALLING THE CHARCOAL FILTER
1. Remove the screws on the top of the grill using a #1 Phillips screwdriver.
2. Open the door. 3. Remove the grill. Push the grill left, and then pull the grill straight off.
Charcoal filter
4. Install the charocal filter. When properly installed, the wire mesh of the filter should be visible from the front.
5. Reinstall the grill and the screws. 6. Close the door.
Insert mesh-side up
MC17T8000CS_AA_DE68-04129D-01_EN.indd 13 2021-03-25 11:25:55
14
Step-by-step installation guide
C. OUTSIDE BACK EXHAUST (HORIZONTAL DUCT)
C1. ADAPTING THE MICROWAVE BLOWER FOR OUTSIDE BACK EXHAUST
1. Remove and save the screws that hold the Blower Plate to the microwave.
Back of Microwave Oven
Blower Retaining Screws
2. Open the blower door by lifting it up at the back of the microwave. Remove and save the blower shield on the back of the microwave by sliding it up.
3. Carefully pull out the blower unit. The wires will extend far enough to allow you to adjust the blower unit.
BEFORE: Fan Blade Openings Facing Forward
End B
End A
CAUTION: To avoid breaking or cracking the blower blade, do not touch the blade. Hold the outer case of the blower when you pull it out or put it back in place.
4. Remove Parts A with tin snips or pliers.
Parts A
5. Rotate the blower unit counterclockwise 180 . Before Rotation After Rotation
Back of Microwave Back of Microwave
6. Place the blower unit back into the opening. AFTER: Fan Blade Openings Facing Back
End B
End A
CAUTION: Do not pull or stretch the blower unit wiring. Make sure the wires are not pinched.
NOTE: The blower unit exhaust openings should match exhaust openings on the rear of microwave oven.
7. Close the blower door. Slide blower shield onto the top of the blower door opening. Secure the blower to the microwave oven using the blower retaining screws from Step 1 except the upper blower motor retaining screw.
Blower Retaining Screw
Blower Shield
Blower Retaining Screw
Back of Microwave Oven
8. Slide the exhaust adaptor onto the back of the microwave oven, securing it into the lower locking tabs. Take care to ensure that the damper hinge is installed so that it is at the top and that the damper swings freely. Reinstall the upper blower motor screw through the adaptor and the blower door and into the back of the microwave oven.
Guide
Guide
Adaptor Locking Tabs (not shown)
Blower Motor Door Retaining Screw
Back of Microwave Oven
MC17T8000CS_AA_DE68-04129D-01_EN.indd 14 2021-03-25 11:25:56
15
Step-by-step installation guide
B. ATTACH THE MOUNTING PLATE TO THE WALL
Attach the plate to the wall using toggle bolts. At least one wood screw must be used to attach the plate to a wall stud.
1. Remove the toggle wings from the bolts. 2. Insert the bolts into the mounting plate through
the holes designated to go into drywall, and then reattach the toggle wings so that of the bolt protrudes beyond the wing.
INSTALLATION OVERVIEW A. Prepare Rear Wall (horizontal duct only) B. Attach Mounting Plate to Wall C. Prepare Top Cabinet D. Mount the Microwave Oven E. Connecting Ductwork (vertical duct only)
A. PREPARING THE REAR WALL FOR OUTSIDE BACK EXHAUST
You need to cut an opening in the rear wall for outside back exhaust (horizontal duct only).
CL
Read the instructions for outside back exhaust on the REAR WALL TEMPLATE.
Tape the REAR WALL TEMPLATE to the rear wall. Cut the opening, following the instructions on the
REAR WALL TEMPLATE. CAUTION: Do not cut an opening in the rear wall if you are installing the microwave with vertical duct or non- vented ductless ventilation.
3. INSTALLATION
MC17T8000CS_AA_DE68-04129D-01_EN.indd 15 2021-03-25 11:25:56
16
Step-by-step installation guide
To use toggle bolts:
Wall
Toggle Wings Toggle Bolt
Bolt End
Spacing for Toggles More Than Wall Thickness
Mounting Plate
Spacing for Toggles More Th all Thickness
Bolt
Mounting Plate To l
B l
le Wings
3. Place the mounting plate against the wall and insert the toggle wings into the holes in the wall to mount the plate.
NOTE: Before tightening the toggle bolts and wood screw, make sure the bottom of the Mounting plate runs along the bottom Horizontal line of the Rear wall Template and the Mounting plate is properly centered under the cabinet.
CAUTION: Be careful to avoid pinching your fingers between the back of the mounting plate and the wall.
4. Tighten all bolts. Pull the plate away from the wall to help tighten the bolts. Tighten the screw.
C. USE THE TOP CABINET TEMPLATE TO PREPARE THE TOP CABINET
You need to drill holes for the top support screws and a hole large enough for the power cord to fit through.
You need to cut an opening on the top cabinet for outside top exhaust(vertical duct only).
Read the instructions on the TOP CABINET TEMPLATE.
Tape it underneath the top cabinet. Drill the holes, following the instructions on the
TOP CABINET TEMPLATE. Minimum hole diameter for power cord is 1 CAUTION: Wear safety goggles when drilling holes in the cabinet bottom.
D. MOUNT THE MICROWAVE OVEN
FOR EASIER INSTALLATION AND PERSONAL SAFETY, WE RECOMMEND THAT TWO PEOPLE INSTALL THIS MICROWAVE OVEN.
IMPORTANT: Do not grip or use the handle during installation.
NOTE: If your cabinet is metal, use the nylon grommet in the power cord hole to prevent the cord from being cut.
NOTE: Filler blocks are required when mounting this unit under any cabinet with a recessed bottom or front overhang. (See page 9.)
IMPORTANT: The case damage that will occur from over tightening screws if you do not use filler blocks is not covered under warranty.
NOTE: When mounting the microwave oven, thread the power cord through hole in the bottom of the top cabinet. Keep it tight throughout Steps 13. Do not pinch the cord or lift the oven by pulling cord.
1. Lift the microwave, tilt it forward, and hook the slots at the back bottom edge onto the four lower tabs of the mounting plate.
2. Rotate the front of the oven up against the cabinet bottom.
3. Insert a self-aligning screw through the top center cabinet hole. Temporarily secure the oven by turning the screw at least two full turns after the threads have engaged. (It will be completely tightened later.) Be sure to keep the power cord tight. Be careful not to pinch the cord, especially when mounting flush to the bottom of cabinet.
MC17T8000CS_AA_DE68-04129D-01_EN.indd 16 2021-03-25 11:25:56
17
Step-by-step installation guide
Cabinet Front
Filler Block
Microwave Oven Top
Self-Aligning Screw
Equivalent to Depth of Cabinet Recess
Cabinet Bottom Shelf
uivalent to epth of Cabinet
Recess
inet Bottom Shelf
Microwave Oven Top
Cabi t Front
Fi r Block
elf-Aligning Screw
4. Attach the microwave oven to the top cabinet. 5. Insert the 2 self-aligning screws through the cabinet
bottom shelf and filler block into the outer top cabinet of the unit. Continue to support the unit until both screws are inserted and engaged at least two full turns, then fully tighten all screws until the unit is secure.
Only for MC17*******modelsnly for 17******* odels
6. Install the grease filters. Check the web manual on the SAMSUNG web site for instructions.
E. CONNECTING DUCTWORK FOR OUTSIDE TOP EXHAUST
House DuctHouse uct
1. Extend the house duct down to connect to the exhaust adaptor.
2. Seal the exhaust duct joints using duct tape.
MC17T8000CS_AA_DE68-04129D-01_EN.indd 17 2021-03-25 11:25:56
18
Before You Use Your Microwave
1. Make sure the microwave oven has been installed according to instructions.
2. Remove all packing material from the microwave oven.
3. Install the turntable and ring in cavity.
4. Replace the house fuse or turn the breaker back on.
Insure proper ground exists before use
5. Plug the power cord into a dedicated 15 amp electrical outlet.
Insure proper ground exists before use
Insure proper ground exists before use.
6. Read the Owners Manual.
7. Keep installation instructions for the local inspectors use.
4. BEFORE YOU USE YOUR MICROWAVE
MC17T8000CS_AA_DE68-04129D-01_EN.indd 18 2021-03-25 11:25:56
19
Note
MC17T8000CS_AA_DE68-04129D-01_EN.indd
Related manuals for Samsung MC17T8000C Microwave Installation Guide
Manualsnet FAQs
If you want to find out how the MC17T8000C Samsung works, you can view and download the Samsung MC17T8000C Microwave Installation Guide on the Manualsnet website.
Yes, we have the Installation Guide for Samsung MC17T8000C as well as other Samsung manuals. All you need to do is to use our search bar and find the user manual that you are looking for.
The Installation Guide should include all the details that are needed to use a Samsung MC17T8000C. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.
The best way to navigate the Samsung MC17T8000C Microwave Installation Guide is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.
This Samsung MC17T8000C Microwave Installation Guide consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.
You can download Samsung MC17T8000C Microwave Installation Guide free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.
To be able to print Samsung MC17T8000C Microwave Installation Guide, simply download the document to your computer. Once downloaded, open the PDF file and print the Samsung MC17T8000C Microwave Installation Guide as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.