Contents

Samsung DVD-AR650 DVD Player User Manual PDF

1 of 89
1 of 89

Summary of Content for Samsung DVD-AR650 DVD Player User Manual PDF

Instruction Manual

DVD-AR650

www.samsung.com AK68-01378A

01378A-AR650-XAA-ENG.indb 1 2007-03-13 11:53:28

G et

tin g

St ar

te d

English - 2

Warning TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE THE COVER(OR BACK). NO USER-SERVICEABLE PARTS ARE INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

This symbol indicates that dangerous voltage consisting a risk of electric shock is present within this unit.

This symbol indicates that there are important operating and maintenance instructions in the literature accompanying this unit.

Do not install this equipment in a con ned space such as a bookcase or similar unit.

WARNING : To prevent damage which may result in re or electric shock hazard, do not expose this appliance to rain or moisture.

CAUTION : DVD RECORDERS USE AN INVISIBLE LASER BEAM WHICH CAN CAUSE HAZARDOUS RADIATION EXPOSURE IF DIRECTED. BE SURE TO OPERATE THE RECORDER CORRECTLY AS INSTRUCTED.

CAUTION THIS PRODUCT UTILIZES A LASER. USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE. DO NOT OPEN COVERS AND DO NOT REPAIR YOURSELF. REFER SERVICING TO QUALIFIED PERSONNEL.

CAUTIONS Caution: To prevent electric shock, match wide blade of plug to wide slot, fully insert. Attention: Pour viter les chocs lectriques, introdure la lame la plus large de la che dans la borne correspondante de la prise et pousser jusqu au fond. This product satis es FCC regulations when shielded cables and connectors are used to connect the unit to other equipment. To prevent electromagnetic interference with electric appliances, such as radios and televisions, use shielded cables and connectors for connections. FCC NOTE (for U.S.A): This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.

Caution: FCC regulations state that any unauthorized changes or modi cations to this equipment may void the user's authority to operate it.

Getting Started

This unit can be used only where the power supply is AC 120V, 60Hz. It cannot be used elsewhere. This DVD Recorder is designed and manufactured to respond to the Region Management Information. If the Region number of a DVD disc does not correspond to the Region number of this DVD Recorder, the DVD Recorder cannot play the disc.

01378A-AR650-XAA-ENG.indb 2 2007-03-13 11:54:00

G etting Started

English - 3

Precaution

Important Safety Instructions Read these operating instructions carefully before using the unit. Follow all the safety instructions listed below. Keep these operating instructions handy for future reference.

1) Read these instructions. 2) Keep these instructions. 3) Heed all warnings. 4) Follow all instructions. 5) Do not use this apparatus near water. 6) Clean only with a dry cloth. 7) Do not block any ventilation openings, Install in

accordance with the manufacturer's instructions. 8) Do not install near any heat sources such as radiators,

heat registers, stoves, or other apparatus (including ampli ers) that produce heat.

9) Do not defeat the safety purpose of the polarized or grounding- type plug. A polarized plug has two blades with one wider than the other. A groundingtype plug has two blades and a third grounding prong. The wide blade or the third prong is provided for your safety. If the provided plug does not t into your outlet, consult an electrician for replacement of the obsolete outlet.

10) Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11) Only use attachments/accessories speci ed by the manufacturer.

12) Use only with the cart, stand, tripod, bracket, or table speci ed by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/ apparatus combination to avoid injury from tip-over.

13) Unplug this apparatus during lightning storms or when unused for long periods of time.

14) Refer all servicing to quali ed service personnel. Service is required when the apparatus has been damaged in any way, such as the power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus. Service is also required if the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

Handling Cautions Before connecting other components to this recorder, be

sure to turn them all off. Do not move the recorder while a disc is being played, or

the disc may be scratched or broken, and the recorders internal parts may be damaged.

Do not put a ower vase lled with water or any small metal objects on the recorder.

Be careful not to put your hand into the disc tray. Do not place anything other than the disc in the disc tray.

Exterior interference such as lightning and static electricity can affect normal operation of this recorder. If this occurs, turn the recorder off and on again with the POWER button, or disconnect and then reconnect the AC power cord to the AC power outlet. The recorder will operate normally.

Be sure to remove the disc and turn off the recorder after use.

Disconnect the AC power cord from the AC outlet when you dont intend to use the recorder for long periods of time.

Clean the disc by wiping in a straight line from the inside to the outside of the disc.

Apparatus shall not be exposed to dripping or splashing and no objects lled with liquids, such as vases, shall be placed on the apparatus.

The Mains plug is used as a disconnect device and shall stay readily operable at any time.

Maintenance of Cabinet For safety reasons, be sure to disconnect the AC power cord from the AC outlet. Do not use benzene, thinner, or other solvents for

cleaning. Wipe the cabinet with a soft cloth.

Disc Handling Use discs with regular

shapes. If an irregular disc (a disc with a special shape) is used, this DVD Recorder may be damaged.

Holding discs Avoid touching the surface of a disc

where recording is performed.

DVD-RAM, DVD-RW and DVD-R Clean with an optional DVD-RAM/PD disc

cleaner . Do not use cleaners or cloths for CDs to clean DVD-RAM/ DVD-RW/DVD-R discs.

DVD-Video, Audio CD Wipe off dirt or contamination on the disc with a soft

cloth.

Cautions on handling discs Do not write on the printed side with a ball-point pen or

pencil. Do not use record cleaning sprays or antistatic. Also, do

not use volatile chemicals, such as benzene or thinner. Do not apply labels or stickers to discs. (Do not use discs xed with exposed tape adhesive or leftover peeled-off stickers.)

Do not use scratch-proof protectors or covers. Do not use discs printed with label printers available on

the market. Do not load warped or cracked discs.

01378A-AR650-XAA-ENG.indb 3 2007-03-13 11:54:02

G et

tin g

St ar

te d

English - 4

Disc Storage Be careful not to damage the disc because the data on these discs are highly vulnerable to the environment. Do not keep under direct sunlight. Keep in a cool ventilated area. Store vertically. Keep in a clean protection jacket. If you move your DVD Recorder suddenly from a cold

place to a warm place, condensation may generate on the operating parts including the lens and cause abnormal disc playback. When this occurs, do not connect the plug to the power outlet. Wait for two hours, then insert the disc and try to playback again. It will work properly when condensation has evaporated.

Disc Speci cations DVD-Video A digital versatile disc (DVD) can contain up to

135-minutes of images, 8-language audio and 32 subtitle languages. It is equipped with MPEG-2 picture compression and Dolby 3D surround sound, allowing you to enjoy vivid and clear theater quality images in the comfort of your own home.

When switching from the rst layer to the second layer of a double-layered DVD Video disc, there may be momentary distortion in the image and sound. This is not a malfunction of the unit.

Once a DVD-R/DVD-RW(V) recorded is nalized, it is playable in a standard DVD player.

Audio CD An audio disc on which 44.1kHz PCM Audio is recorded Plays CD-DA format audio CD-R and CD-RW discs.

The unit may not be able to play some CD-R or CD-RW discs due to the condition of the recording.

CD-R/-RW MP3 CD-R/-RW

Only CD-R discs with MP3 les recorded with ISO9660 or JOLIET format can be played back

Only MP3 les with the ".mp3", ".MP3" extension can be used.

For MP3 les recorded with a VBR(Variable Bit Rates), from 32 Kbps to 320 Kbps, the sound may cut in out.

Playable bitrate range is from 56Kbps to 320Kbps. The unit can handle a maximum of 1000 les and

folders.

JPEG CD-R/-RW Only JPEG les with the ".jpg", ".JPG" extension can be

used. The unit can handle a maximum of 1000 les and

folders. Maximum size of progressive JPEG is 3M pixels. MOTION JPEG is not supported.

Using MPEG4 disc Disc : CD-R/-RW, DVD-RAM, DVD-R/ DVD-RW, MPEG4 File with following extensions can be played. :

.avi, .divx, .AVI, .DIVX MPEG4 Codec format : DivX 3.11 DivX 4.x DivX 5.x Available Audio Format : MP3, MPEG, PCM,AC3,

DTS Supported subtitle le formats: .smi, .srt, .sub, .psb,.txt

Using CD-R/-RW Use a 700MB(80 minutes) CD-R/-RW disc. If possible,

do not use a 800MB(90 minutes) or above disc, as the disc may not play back.

If the CD-R/-RW disc was not recorded as a closed session, you may experience a delay in the early playback time, and all recorded les may not play.

Some CD-R/-RW discs may not be playable with this unit, depending on the device which was used to burn them.

When recording from CDs for your personal use to CD- R/-RW discs on your computer, playability may vary depending on the contents and discs.

DVD-R Disc Playback and Recording Once a DVD-R recorded is nalized, it is playable in a

standard DVD player. You can record onto the available space on the disc and perform editing functions such as giving titles to discs and programs and erasing programs before nalizing.

When programming is erased from a DVD-R, that space does not become available. Once an area on a DVD-R is recorded on, that area is no longer available for recording, whether the recording is erased or not.

It takes about 30 seconds for the unit to complete recording management information after recording nishes.

This product optimizes the DVD-R for each recording. Optimization occurs when you start recording after inserting the disc or turning on the unit. Recording onto the disc may become impossible if optimization is carried out too many times.

Playback may be impossible in some cases due to the condition of recording.

This unit can play back DVD-R discs recorded and nalized with a Samsung DVD video recorder. It may not be able to play some DVD-R discs depending on the disc and the condition of the recording.

DVD-RW Disc Playback and Recording Recording and playback can be performed on DVD-RW

discs in both the Video and VR Modes. Once a DVD-RW recorded in VR or Video mode is nalized, you cannot perform additional recording.

Once a DVD-RW is recorded in Video Mode and nalized, it becomes a DVD-Video.

In both modes, playback can be performed before and after nalization, but additional recording, deleting and editing can not be performed after nalization.

If you want to record the disc in VR Mode and then record in V Mode, be sure to rst reformat the disc. Please be aware that formatting may erase all of the disc's content.

01378A-AR650-XAA-ENG.indb 4 2007-03-13 11:54:04

G etting Started

English - 5

When inserting an unused disc, a message will appear asking whether to initialize the disc or not. If you select "YES", the disc will be formatted in VR mode.

DVD-RW (VR mode) - This is a format that is used for recording data on a

DVD-RW disc. You can record multiple titles, edit, delete, partial delete, create a playlist, etc.

- A disc that is recorded in this mode will not play in standard DVD players.

DVD-RW (Video mode) - This is a format that is used for recording data on a

DVD-RW or DVD-R disc. The disc can be played by an existing DVD player once it has been nalized.

- If a disc that has been recorded in Video Mode by a different makers recorder but has not been nalized, it cannot be played or recorded by this recorder.

DVD-RAM Disc Playback and Recording For cartridge type DVD-RAM discs, remove the cartridge

and use only the disc Ensure that the recording mode is set to VR.

Otherwise, this product will not be able to play the recording.

You cannot play a DVD-RAM in most DVD players due to compatibility issues.

Only DVD-RAM standard Version 2.0 discs can be played in this unit.

DVD-RAM discs recorded on this unit may not work with other DVD Players. To determine compatibility with these DVD-RAM discs, refer to the users manual for the player.

COPY PROTECTION

Many DVD discs are encoded with copy protection. Because of this, you should only connect your DVD Recorder directly to your TV, not to a VCR. Connecting your DVD recorder to a VCR results in a distorted picture from copy-protected DVD discs.

This product incorporates copyright protection technology that is protected by methods claims of certain U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this copyright protection technology must be authorized by Macrovision Corporation, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited.

Protection This DVD Recorder can allow you to protect the contents of your discs, as described below. Program-protection: See page 69 Locking a Title Disc-protection: See page 76 Disc Protection

DVD-RAM/DVD-RW/DVD-R discs that are incompatible with the DVD-VIDEO format cannot be played with this product. For more information on DVD recording compatibility, consult your DVD-RAM/DVD-RW/DVD-R manufacturer. Use of poor quality DVD-RAM/DVD-RW/DVD-R discs may cause the following unexpected problems including, recording failure, loss of recorded or edited materials or damage to the recorder.

Do not use the following discs! LD, CD-G, CD-I, CD-ROM and DVD-ROM discs should

not be used in this product. [Note] Disc types that can be played : CD/CD-R/CD-RW/MP3/JPEG/DVD-Video/DVD-RAM/ DVD-RW/ DVD-R. DVD+R/+RW cannot record, but nalized +R/+RWs can be played. A DVD-R/DVD-RW disc which has been recorded in Video Mode on another component can play only when nalized. Some commercial discs and DVD discs purchased

outside your region may not be playable with this product. When these discs are played, either No Disc." or "The disc cannot be played. Please check the regional code of the disc." will be displayed.

If your DVD-RAM/DVD-RW/DVD-R disc is an illegal copy or is not in DVD video format, it may also not be playable.

Disc Compatibility Not all brands of discs will be compatible with this unit. The latest rmware upgrade to improve recording &

playback quality can be downloaded from our web site. (Download Center at www.samsung.com)

If disc compatibility problems continue, or there is an issue upgrading your recorder, contact the Call Center at 1-800-SAMSUNG.

01378A-AR650-XAA-ENG.indb 5 2007-03-13 11:54:05

G et

tin g

St ar

te d

English - 6

Contents

Getting Started

Warning ...................................................................2

Precaution ...............................................................3 Important Safety Instructions ..................................3 Handling Cautions ...................................................3 Maintenance of Cabinet ..........................................3 Disc Handling ..........................................................3 Disc Storage ............................................................4 Disc Speci cations ..................................................4

General Features ....................................................8

Before Reading the Instruction Manual ...................9

How to use the DVD Recorder ................................9

Unpacking ...............................................................10 Accessories .............................................................10 Preparing the Remote Control ................................10 Tour of the Remote Control .....................................12

Description ..............................................................13 Front Panel ..............................................................13 Front Panel Display .................................................13 Rear Panel ..............................................................14

Connecting & Setting Up

Step 1: Connecting the Antenna Cable ...................15 Antenna + DVD Recorder + TV ...............................15 Antenna + Cable box or satellite receiver (set top box) + DVD Recorder + TV : Cable box/Satellite receiver with a video/audio output ..................................................16 Antenna + Cable box or satellite receiver (set top box) + DVD Recorder + TV : Cable box/Satellite receiver with an antenna output only ................................................ 17

Step 2 : Connecting HDMI/DVI to a TV ...................18 Connecting to a TV with HDMI Jack .......................18 Connecting to a TV with DVI Jack ...........................19

Step 3 : Connecting the Video Cable ......................20 Connecting to Component Video Input Jacks (Y,PB,PR) ..................................................................20 Connecting to an S-Video Input Jack ......................21 Connecting to a Video Input Jack ...........................22

Step 4 : Connecting the Audio Cable ......................23 Connecting to your TV ............................................23 Connecting to a Stereo Ampli er with Analog Input Jacks .......................................................................24 Connecting to an AV Ampli er with a Digital Input Jack .........................................................................25

Step 5 : Connecting External Devices .....................26 Connecting a VCR, Cable box/Satellite receiver (set top box) or DVD Player to the AV 1 IN or S-VIDEO IN Jacks ...................................................26 Connecting a Camcorder ........................................27

System Setup

On-Screen Menu Navigation ...................................28

Plugging In & Auto Setup ........................................28

Auto Clock Set .........................................................29 Time Zone ...............................................................29 Daylight Saving .......................................................29

Manual Clock Set ....................................................30

Auto Channel Memory .............................................30

Manual Channel Set ................................................31

Setting Up the System Options ...............................32 Set Top Box Control ................................................32 CM Skip Time Setting ..............................................33 EP Mode Time Setting ............................................34 Automatic Chapter Creation ....................................34 Quick Recording Setting .........................................35 Anynet+(HDMI-CEC)...............................................35

Language Setting ....................................................36

Digital Caption .........................................................37

Setting Up the Audio Options ..................................38

Video(Display) Setting .............................................39 TV Aspect ................................................................39 Input Level ...............................................................39 Black Level ..............................................................40 3D Noise Reduction ................................................40 HDMI/DVI Resolution ..............................................40 DivX(R) Registration ...............................................40

Parental Control ......................................................41 Setting the Rating Level ..........................................41 Setting the Digital Rating .........................................41 Changing the Password ..........................................42

EPG-Electronic Program Guide ..............................42 Viewing Full Guide and Mini Guide .........................43 EPG Timer Recording .............................................43

01378A-AR650-XAA-ENG.indb 6 2007-03-13 11:54:06

G etting Started

English - 7

Recording

Recordable discs .....................................................44 Compatibility between Samsung and Other manufacturer's Recorders .......................................44

Recording Formats ..................................................45 DVD-RAM/-RW(VR mode) ......................................45 DVD-RW(Video mode)/-R .......................................45

Recording Mode ......................................................46

Unrecordable Video .................................................46 About the INFO Button ............................................47

Recording immediately ............................................48 Recording the current TV program you are watching .. 48 Recording from External Equipment .......................48

Copying from a Camcorder .....................................49

Making a One Touch Recording (OTR) ...................50

Setting a Timer Recording .......................................51

Flexible Recording (for Timer Recording only) ........52

Editing the Scheduled Record List ..........................52

Deleting the Scheduled Record List ........................53

Recording the Scheduled Record List .....................53

EZ REC MODE .......................................................54

Playback

Region code (DVD-Video only) ...............................55

Logos of Discs that can be played ..........................55

Disc types that can be played .................................55 Discs That Cannot be Played ..................................56

Playing a Disc ..........................................................56 Using the Disc Menu & Title Menu ..........................57 Using the Playback Related Buttons .......................57 Slow Motion Play .....................................................58 Step Motion Play .....................................................58 Using the ANYKEY Button ......................................59

Playing an Audio CD/MP3 .......................................63 Playing an Audio CD(CD-DA) .................................63 Playing an MP3 Disc ...............................................64 Playing Repeatedly .................................................64

Playing a Picture CD ...............................................65

Playing an MPEG4 Disc ..........................................66

Playing the Title List ................................................67

Editing

Basic Editing (Title List) ...........................................68 Renaming (Labeling) a Title ....................................68 Locking (Protecting) a Title ......................................69 Deleting a Title ........................................................69 Deleting a Section of a Title ....................................70

Advanced Editing (Playlist) ......................................71 Creating a Playlist ...................................................71 Playing Entries in the Playlist ..................................71 Renaming a Playlist Entry .......................................72 Editing a Scene for the Playlist ...............................72 Copying a Playlist Entry to the Playlist ....................75 Deleting a Playlist Entry from the Playlist ................75

Disc Manager ..........................................................75 Editing the Disc Name .............................................75 Disc Protection ........................................................76 Formatting a Disc ....................................................76 Finalizing a Disc ......................................................77 Un nalizing a Disc (V/VR mode) .............................77 Delete All Title Lists .................................................78

Additional Information

Troubleshooting .......................................................79

Cable Box/Satellite Receiver Brand Code Table .....81 Cable box brand ......................................................81 Satellite receiver brand ...........................................83

Error Message Solutions .........................................84

Speci cations ..........................................................86

Warranty ..................................................................87

01378A-AR650-XAA-ENG.indb 7 2007-03-13 11:54:08

G et

tin g

St ar

te d

English - 8

General Features The DVD-AR650 allows you to record and play high quality digital video on DVD-RAM/DVD-RW/DVD-R discs.

High quality digital audio and video recording and playback You can record up to approximately 16-hours of video on a double side 9.4 GB DVD-RAM disc,up to 15-hours on a dual-layer 8.5GB DVD-R disc, and up to 8-hours on a 4.7 GB DVD-RAM/DVD-RW/DVD-R disc, depending on the recording mode.

Selectable Record Mode You can set your recorder to one of ve different recording speeds, each varying in recording quality and length. EP mode yields the most recording time, LP & SP modes provide less recording time with higher quality recording, and XP mode gives you the highest quality recording. There's also the FR (Flexible Recording) mode that lets you record with the best picture quality possible for the recording time and remaining space on the disc during timer recording.

Automated Quality Adjustment for Timer Recording If FR mode is selected, the video quality is adjusted automatically so that all video for the scheduled time can be recorded onto the free disc space. (See pages 51~52)

Create a DVD video title using a DVD-RW/DVD-R disc With the DVD-AR650, you can create your own DVD video title on 4.7 GB DVD-RW/DVD-R or 8.5GB DVD-R discs.

Copying data from a digital camcorder using a DV input jack Record digital camcorder video onto DVD-RAM, DVD-RW or DVD-R discs using the DV input jack (IEEE 1394-4pin). (See page 49)

High quality progressive scan Progressive scanning provides high resolution and icker free video. The 10-bit 54-MHz DAC and 2D Y/C Separating Circuitry provides the highest video playback and recording quality. (See page 20)

A variety of functions with an easy-to-use user interface The integrated menu system and the messaging function allows you to perform desired operations both easily and conveniently. With a DVD-RAM or DVD-RW (VR mode) disc, you can edit recorded images, create a playlist, and edit videos in a speci c sequence according to your requirements.

MPEG4 playback This DVD Recorder can play MPEG4 formats within an avi le.

DivX Certi cation DivX, DivX Certi ed, and associated logos are trademarks of DivXNetworks, Inc and are used under license.

HDMI (High De nition Multimedia Interface) HDMI reduces picture noise by allowing a pure digital video/audio signal path from the DVD Recorder to your TV.

EZ REC MODE This function allows you to Initialize and Finalize a disc automatically. (See page 54)

01378A-AR650-XAA-ENG.indb 8 2007-03-13 11:54:09

G etting Started

English - 9

Before Reading the Instruction Manual

Make sure to check the following before reading the users manual.

Icons that will be used in manual

Icon Term De nition

DVD

This involves a function available with DVD or DVD-R/DVD-RW (V) discs that have been recorded and nalized.

RAM This involves a function available with DVD-RAM discs.

-RW This involves a function available with DVD-RW discs.

-R This involves a function available with DVD-R discs.

CD This involves a function available with a data CD (CD-R or CD-RW).

JPEG This involves a function available with JPEG les on CD-R/-RW or DVD-RAM/DVD-RW/DVD-R discs.

MP3 This involves a function available MP3 les on CD-R/-RW or DVD- RAM/DVD-RW/DVD-R discs.

MPEG4 This involves a function available with MPEG4s on CD-R/-RW or DVD-RAM/DVD-RW/DVD-R discs.

Caution This involves a case where a function does not operate or settings may be cancelled.

NOTE This involves tips or instructions on the page that help each function operate.

One- Touch button

A function that can be operated by using only one button.

ANYKEY button

A function that can be operated by using the ANYKEY button.

About the use of this Instruction Manual

1) Be sure to familiarize yourself with the Safety Instructions before using this product. (See pages 2 ~ 5)

2) If a problem occurs, check the Troubleshooting section. (See pages 79~80)

Copyright

2007 Samsung Electronics Co. All rights reserved; No part or whole of this users manual may be reproduced or copied without the prior written permission of Samsung Electronics Co.

How to use the DVD Recorder

Step 1 : Select the disc type This unit can record on the following types of discs. If you want to repeatedly record on the same disc or you want to edit the disc after recording, select a rewritable DVD-RW or DVD-RAM type disc. If you want to save the recording without making any changes, choose a non-rewritable DVD-R.

Step 2 : Format the disc to start recording The recorder automatically starts formatting when an unused disc is inserted. This is required for the preparation of disc recording.

Using a DVD-RAM This type of disc can be formatted with the DVD-Video Recording format (VR mode). You can edit recorded video and create a playlist and edit video in a speci c sequence according to your requirements.

Using a DVD-RW When an unused DVD-RW disc is rst inserted, the

message Uninitialized Disc. Do you want to initialize this disc? will be displayed. If you select Yes, initializing will begin. A DVD-RW disc can be formatted in either DVD-Video format (Video mode) or DVD-Video Recording format (VR mode)

Using a DVD-R When using a DVD-R disc, only V mode recording is possible and no initialization is needed to play it on this recorder. However, nalization is necessary to play this disc on other DVD players.

You can only use either the VR or Video mode on a DVD-RW, but not both at the same time. You can format a DVD-RW to V or VR mode using disc manager. It should be noted that the disc's data will be lost when changing formats.

Step 3 : Recording There are two different recording methods. Direct Recording (recording a program you are currently watching) and Timer Recording. Timer recording is determined as a Date : MM/DD, MON-FRI, Every SAT, etc.. There are 5 recording modes : XP(high quality mode), SP(standard quality mode), LP(long recording mode), EP(extended mode) and FR mode. When using FR mode to record, the picture quality is determined by the remaining time on the disc.

You can make a Timer Recording by using the EPG (Electronic Program Guide). (See page 43)

01378A-AR650-XAA-ENG.indb 9 2007-03-13 11:54:10

G et

tin g

St ar

te d

English - 10

Step 4 : Playing To start playback select the title you want to play from the Title list. A DVD consists of sections called titles, and sub sections called chapters. During recording, a title is created between two points where you start and stop recording. Chapters will be created automatically when you nalize recording on DVD-R/DVD-RW discs in Video mode.

Step 5 : Editing a recorded disc Editing on discs is easier than editing on conventional video tapes. The recorder supports many different edit functions, possible only with DVDs.

With a simple and easy edit menu, you can operate various edit functions, such as delete, copy, rename, lock, etc., on a recorded title.

With this recorder, you can create playlists using a DVD- RAM/DVD-RW in VR mode. Once a playlist is created you can create/edit a new playlist on the same disc without changing the original recording.

Step 6 : Finalizing & Playing on other DVD components

To play your DVD on other DVD components, nalizing may be necessary. First, nish all editing and recording operations, then nalize the disc. When using a DVD-RW disc in VR Mode Although nalizing is generally unnecessary when playing the disc on a VR Mode compatible component, a nalized disc should be used for playback. When using a DVD-RW disc in Video Mode The disc should be nalized rst to enable playback on anything other than this recorder. No more editing or recording can be made on the disc once it has been nalized. When using a DVD-R disc You should nalize the disc to play it on a component other than this recorder. No more editing or recording can be made on the disc once it has been nalized.

You can nalize automatically using the EZ REC MODE. (See page 54)

Unpacking

Accessories Check for the supplied accessories below.

Preparing the Remote Control Install Batteries in the Remote Control Open the battery cover on the back of the remote. Insert two AAA batteries. Make sure that the polarities

(+ and -) are aligned correctly. Replace the battery cover.

If the remote control does not operate properly: Check the polarity +/- of the batteries. Check if the batteries are drained. Check if the remote sensor is blocked by obstacles. Check if there is any uorescent lighting nearby.

Dispose of batteries according to local environmental regulations. Do not put them in the household trash.

IR Blaster cable (AK39-00055A)

Video/Audio Cable (AC39-00073A)

Quick Guide (AK68-01379A)

Instruction Manual (AK68-01378A)

Remote Control (AK59-00062J)

Batteries for Remote Control (AAA Size)

(AC43-12002H)

01378A-AR650-XAA-ENG.indb 10 2007-03-13 11:54:13

Brand BUTTON AIWA 82 ANAM 10, 11, 12, 13, 14, 15, 16, 17, 18 BANG & OLUFSEN

57

BLAUPUNKT 71 BRANDT 73 BRIONVEGA 57 CGE 52 CONTINENTAL EDISON 75 DAEWOO 19, 20, 23, 24, 25, 26, 27, 28, 29, 30, 31, 32, 33, 34 EMERSON 64 FERGUSON 73 FINLUX 06, 49, 57 FORMENTI 57 FUJITSU 84 GRADIENTE 70 GRUNDIG 49, 52, 71 HITACHI 60, 72, 73, 75 IMPERIAL 52 JVC 61, 79 LG 06, 19, 20, 21, 22, 78 LOEWE 06, 69 LOEWE OPTA 06, 57 MAGNAVOX 40 METZ 57 MITSUBISHI 06, 48, 62, 65 MIVAR 52, 77 NEC 83 NEWSAN 68 NOBLEX 66 NOKIA 74 NORDMENDE 72, 73, 75 PANASONIC 53, 54, 74, 75 PHILIPS 06, 55, 56, 57 PHONOLA 06, 56, 57 PIONEER 58, 59, 73, 74 RADIOLA 06, 56 RADIOMARELLI 57 RCA 45, 46 REX 74

BRAND BUTTON SABA 57, 72, 73, 74, 75 SALORA 74 SAMSUNG 01,02,03,04,05,06,07,08,09 SANYO 41, 42, 43, 44, 48 SCHNEIDER 06 SELECO 74 SHARP 36, 37, 38, 39, 48 SIEMENS 71 SINGER 57 SINUDYNE 57 SONY 35, 48 TELEAVA 73 TELEFUNKEN 67, 73, 75, 76 THOMSON 72, 73, 75 THOMSON ASIA 80, 81 TOSHIBA 47, 48, 49, 50, 51, 52 WEGA 57 YOKO 06 ZENITH 63

Result: If your television is compatible with the remote control, it will switch off. It is now programmed to operate with the remote control.

If several codes are indicated for your television brand, try each one in turn until you nd one that works. If you replace the remote controls batteries, you must set the brand code again.

If you select TV mode, you can then control your television using the following buttons. Button Function TV POWER Used to switch the television on and off.

INPUT SEL. Used to select an external source. TV VOL +/- Used to adjust the volume of the television.

CH ( / ) Used to select the desired channel.

TV MUTE Used to toggle the sound on and off.

0~9 Used to input number directly.

Various functions may be controllable on your television. If you encounter problems, operate the television directly.

To determine whether your television is compatible, follow the instructions below.

1. Switch your television on. 2. Point the remote control towards the television. 3. Press and hold the TV POWER button and enter the two-figure code simultaneously corresponding to the brand of

your television by pressing the appropriate number buttons.

G etting Started

English - 11

01378A-AR650-XAA-ENG.indb 11 2007-03-13 11:54:15

1 2

20

21

22 23

3

4

5 6 7 8 9

10

11 27

12

13 14 15

19

29

28

26

25 8

6 24

32

34 35

31 30

18

16 17 33

G et

tin g

St ar

te d

English - 12

1. TV Button Press this to operate your TV. 2. DVD Button Press this to operate your DVD Recorder. 3. POWER Button

Press to power the DVD Recorder on and off. 4. NUMBER Buttons 5. DASH (_) Button

Press to select additional channels (digital and analog) being broadcast by the same station. For example, to select channel 54-3, press 54, then press - and 3.

6. REVERSE/FORWARD SKIP Buttons Press to skip a disc backwards or forwards.

7. REVERSE/FORWARD STEP Buttons Press to play frame by frame. 8. REVERSE/FORWARD SEARCH Buttons Press to search a disc backwards or forwards. 9. STOP Button Press to stop a disc or to stop the recording. 10. TV VOL Buttons Volume adjustment. 11. MENU Button Brings up the DVD recorders setup menu. 12. ENTER/DIRECTION Buttons (UP/DOWN and LEFT/RIGHT Buttons) This button functions as a toggle switch.

13. TITLE LIST/DISC MENU Button Use this to enter the View Recording list/Disc menu. 14. ANYKEY Button Use this to view the status of the disc that is being played. 15. TIMER/EPG RED Button Press this to enter the Timer Recording Mode menu.

Set the Timer Rec on the EPG. 16. MARKER/EPG GREEN Button Press this to use Bookmarks or mark a position while

playing a disc. Scroll up the detail information on the EPG.

17. REC Button Use to make a recording on writable/rewritable discs. 18. EZ REC MODE Button Use this to set the EZ REC MODE. 19. REC PAUSE Button Press this to pause the recording. 20. INFO Button This will display current setting or disc status. 21. INPUT SEL. Button Selects line input signal when an external device is

connected. (Analog Ch,Digital Ch,AV1,AV2 or DV) 22. TV POWER Button 23. OPEN/CLOSE Button To open and close the disc tray. 24. CM SKIP/SET Button Press this to skip a portion of the program

automatically during playback of a DVD disc. 25. PLAY/PAUSE Button Press to play/pause a disc. 26. CH Buttons Use this to select a channel. (TV/DVD) 27. TV MUTE/AUDIO Button This operates as Sound Mute. (TV mode)

Use this to access various audio functions on a disc. (DVD mode) Use this to access Multi-sound Broadcasting functions on Air. (DTV mode)

28. RETURN Button Returns to the previous menu. 29. PLAY LIST/TITLE MENU Button Use this to return to the Title menu, or to view the

recorded Playlist. 30. EXIT Button Press this to exit the menu. 31. EPG BLUE Button Press this to go to Full / Mini Guide on the EPG. 32. CAPTION/EPG YELLOW Button Press this to select a caption. (DTV mode)

Also used to scroll down in the EPG. 33. EPG (Electronic Program Guide) Button Press this to display the EPG. (DTV mode) 34. CANCEL Button 35. REC MODE Button Use this to set the desired Recording time and picture quality.(XP/SP/LP/EP)

Tour of the Remote Control You can control certain functions of another manufacturer's TV with this remote control. Buttons that can be controlled on your TV : TV POWER, INPUT SEL., TV VOL (+/-), CH ( / ), TV MUTE, 0~9.

EPG stands for Electronic Program Guide. This is a special remote control for the visually impaired, and has Braille points on the POWER( ), STOP( ) and PLAY( ) buttons.

01378A-AR650-XAA-ENG.indb 12 2007-03-13 11:54:16

G etting Started

English - 13

Front Panel

Front Panel Display

1. Lights when a disc is loaded. 2. Lights in the record mode. 3. Lights to indicate the timer record mode.

4. Lights when a DVD-RAM/DVD-RW/DVD-R disc is loaded. 5. Alpha/Numeric display. 6. Lights in the progressive scan mode.

1. POWER Button Turns the recorder on and off. 2. AV 2 IN Connect external equipment. 3. DV-IN Connects external digital equipment with a DV

jack. (such as a camcorder) 4. DISC TRAY Opens to accept a disc. 5. P.SCAN Button Selects the progressive scan mode. 6. OPEN/CLOSE Button Opens and closes the disc tray. 7. DISPLAY Displays the playing status, time, etc. 8. DTV Lights when a Digital channel is selected.

9. INPUT SEL. Button Selects line input signal in external mode.

(Analog Ch, Digital Ch, AV1, AV2, DV) This allows you to select a TV signal or connected external equipment for recording purposes.

10. CH ( / ) Select channels. 11. REC Button Starts recording. 12. STOP Button Stops disc playback. 13. PLAY/PAUSE Button Plays a disc or pauses playback. 14. SKIP Buttons Go to the next title/chapter/track, or go back to

the previous title/chapter/track.

Description

01378A-AR650-XAA-ENG.indb 13 2007-03-13 11:54:19

Fan The fan always revolves when the power is on. Ensure a minimum of 4 clear space on all sides of the fan when installing the product.

G et

tin g

St ar

te d

English - 14

Rear Panel

1. HDMI OUT (best video quality) Connects the input of external equipment using a HDMI cable. 2. DIGITAL AUDIO OUT(OPTICAL) Connects to an ampli er having a digital optical audio input jack. 3. DIGITAL AUDIO OUT(COAXIAL) Connects to an ampli er having a digital coaxial audio input jack. 4. AV AUDIO OUT Connect to the audio input of external equipmentusing audio cables. 5. AV VIDEO OUT(good video quality) Connects the input of external equipment using a Video cable. 6. AV S-VIDEO OUT(better video quality) Connects the input of external equipment using an S-Video cable.

7. COMPONENT VIDEO OUT (excellent video quality) Connect to equipment having Component video input jacks.

8. AV 1 AUDIO IN Connect the output of external equipment using audio cables 9. AV 1 VIDEO IN Connects the output of external equipment usinga video cable. 10. AV 1 S-VIDEO IN Connects the output of external equipment usingan S-Video cable. 11. ANT IN/ANT OUT (TO TV) Connects antenna cables. 12. CABLE BOX CONTROL OUT Connect the IR Blaster here to control your

cable box or satellite receiver (set top box).

01378A-AR650-XAA-ENG.indb 14 2007-03-13 11:54:21

Connecting & Setting Up

English - 15

Connecting & Setting Up

Step 1: Connecting the Antenna Cable There are several ways to connect your DVD Recorder. Select the antenna connection that best suits you below.

Antenna + DVD Recorder + TV You can record non-scrambled channels by selecting the channel on the DVD Recorder. Also use this method if you watch channels without without a cable box or satellite receiver (set top box).

The VHF/UHF ANT (RF) OUT jack of this product sends only signals received through the antenna. It does not output Audio/Video signals. You must connect Audio/Video cables to view Video from the unit. (i.e. DVD playback)

01378A-AR650-XAA-ENG.indb 15 2007-03-13 11:54:23

Co nn

ec tin

g & Se

ttin g U

p

English - 16

Antenna + Cable box or satellite receiver (set top box) + DVD Recorder + TV : Cable box/Satellite receiver with a video/audio output

You can record channels by selecting the channel on the cable box or satellite receiver (set top box). You cannot record one channel while watching another channel. Be sure that the cable box or satellite receiver (set top box) is turned on.

Connecting the IR Blaster cable into the Cable Box Control jack The Cable Box Controller (IR Blaster) is used to control your cable box for recording purposes. 1. Find and Connect the included IR Blaster cable into the

Cable Box's Control jack of the DVD Recorder. 2. Find the Cable Box IR Sensor

A. Turn the cable box Off. B. Hold the Cable box/Satellite receiver's remote so that

it touches the front of the Cable box/Satellite receiver (see Figure 1).

C. Move the Cable Box's remote across the front of the Cable Box/Satellite Receiver while pressing the remote's power button On and Off (Figure 2).

(Press and release the power button each time you move the remote; holding down the button will not work.) D. When the Cable box/Satellite receiver powers On, you have found the sensor. E. Remember the location of the sensor.

3. Place the IR Blaster. Place the Cable box controller of the IR Blaster on top or underneath the Cable box/Satellite receiver approximately 1 inch in front of the sensor you found in 2. Use the double-sided tape to secure the IR Blaster.

You must select a Cable box/Satellite receiver brand from the table on pages 81~83. If you do not know the brand name, please contact your cable/satellite provider. After setting up your cable box or satellite receiver (Set top box) with the DVD recorder through the IR Blaster cable, you need to set up the Set Top Box Control menu. (See pages 32~33)

Figure 2

Correct

Figure 1

Incorrect

01378A-AR650-XAA-ENG.indb 16 2007-03-13 11:54:24

Connecting & Setting Up

English - 17

Antenna + Cable box or satellite receiver (set top box) + DVD Recorder + TV : Cable box/Satellite receiver with an antenna output only

You can record non-scrambled channels by selecting the channel on the DVD Recorder. You cannot record scrambled channels that require a cable box.

01378A-AR650-XAA-ENG.indb 17 2007-03-13 11:54:27

Co nn

ec tin

g & Se

ttin g U

p

English - 18

Step 2 : Connecting HDMI/DVI to a TV If your TV has an HDMI/DVI input, connect the HDMI/DVI cable to the TV. You will enjoy the best quality image and sound.

Connecting to a TV with HDMI Jack Using an HDMI-HDMI cable, connect the HDMI OUT jack on the rear of the DVD Recorder to the HDMI IN jack of your TV. Turn on your TV, then the DVD Recorder. Press the input selector on your TV remote control until the HDMI signal from the DVD Recorder appears on your TV screen.

To watch through the HDMI output, set the digital audio output to PCM. (See page 38) Depending on the HDMI device(TV/HDMI Receiver) you use, audio may not be supported. If your TV does not support Dolby digital/DTS, Audio output is not available when you set the Digital output to Bitstream or select DTS On in the Audio setup menu. In this case, set the digital audio ouput to PCM or DTS Off. If you use an HDMI cable to connect a Samsung TV to the DVD recorder, you can operate the recorder using the TV remote control. (This is only available with SAMSUNG TVs that support Anynet+(HDMI-CEC).) (See pages 35~36)

Please check the logo (If your TV has an logo, then it supports Anynet+ function.)

01378A-AR650-XAA-ENG.indb 18 2007-03-13 11:54:28

Connecting & Setting Up

English - 19

Connecting to a TV with DVI Jack Using the HDMI-DVI cable (not included), connect the HDMI OUT terminal on the rear of the DVD Recorder to the DVI IN terminal of your TV. An HDMI to DVI connection requires a separate audio connection, using the audio cables, connect the AUDIO (red and white) OUT terminals on the rear of the DVD Recorder to the AUDIO (red and white) IN terminals of your TV. Turn on your TV, then the DVD Recorder. Press the input selector on your TV remote control until the DVI signal from the DVD Recorder appears on your TV screen.

To set the HDMI output resolution (480p/720p/ 1080i), see page 40. HDMI (High De nition Multimedia Interface) HDMI enables you to make a digital video and audio connection with a single cable. Using HDMI, the DVD player transmits a digital video and audio signal and displays a vivid picture on a TV having an HDMI input jack. HDMI is completely compatible with DVI. The only difference between HDMI and DVI is that HDMI supports multi-channel audio. HDMI connection description HDMI connector - Both uncompressed video data and digital audio data (LPCM or Bit Stream data). - The DVD recorder outputs a pure digital signal to

the TV. - If your TV does not support HDCP

(High bandwidth Digital Content Protection), snow noise appears on the screen.

Why does Samsung use HDMI? Analog TVs require an analog video/audio signal.However, when playing a DVD, the data transmitted to a TV is digital. Therefore either a digital-to-analog converter (in the DVD Recorder) or an analog-to-digital converter (in the TV) is required. During this conversion, the picture quality is degraded due to noise and signal loss. HDMI technology is superior because it requires no D/A conversion and is a pure digital signal from the DVD recorder to your TV. What is the HDCP? HDCP (High-bandwidth Digital Content Protection) is a system for protecting DVD content output via HDMI from being copied. It provides a secure digital link between a video source (PC, DVD. etc) and a display device (TV, projector. etc). Content is encrypted at the source device to prevent unauthorized copies from being made.

01378A-AR650-XAA-ENG.indb 19 2007-03-13 11:54:30

Co nn

ec tin

g & Se

ttin g U

p

English - 20

Step 3 : Connecting the Video Cable If you have not connected to your TV via HDMI/DVI, select one of the video connections on the following pages.

Connecting to Component Video Input Jacks (Y,PB,PR)

1. Connect the Component video cables(not supplied) between the COMPONENT OUT(Y,PB,PR) jacks on the DVD Recorder and COMPONENT IN(Y,PB,PR) jacks on your TV (or AV ampli er). This connection outputs the 480i or 480p resolution to your TV.

2. If the connected TV supports Progressive Scan, press the P.SCAN button on the front of the DVD Recorder to enjoy best quality video. Pressing the P.SCAN button alternately switches the Progressive(480p) or Interlace(480i) scan mode on.

You will enjoy the best quality accurate color reproduction images. Component video separates the picture element into black and white(Y), blue(PB) and red(PR) signals to present clear and clean images.

Connect the audio cables(white and red) between the AUDIO OUT jacks on the DVD Recorder and AUDIO IN jacks on your TV(or AV ampli er). (See pages 23~25)

Compared to standard interlaced video, progressive scan doubles the amount of video lines fed to your TV, resulting in a clearer, more stable, and icker free image than interlaced video. The component output jack of the DVD player can be used for progressive output mode, which is only available with TVs that support progressive scan. Progressive Scan Output (480p). Not all high de nition television sets are fully compatible with this product. If the 480p progressive scan picture is not satisfactory, press the P.SCAN button on the unit to switch to the Interlace mode. If there are questions regarding TV set compatibility with this model, please contact our customer service center at 1-800-SAMSUNG. The Component jacks will not output video resolutions above 480p. To view 720p and 1080i, connect the DVD-AR650 to your TV with an HDMI- HDMI cable. With HDMI connected, press the P.SCAN button to alternate between all available resolutions. (See page 40)

01378A-AR650-XAA-ENG.indb 20 2007-03-13 11:54:32

Connecting & Setting Up

English - 21

Connecting to an S-Video Input Jack Connect an S-Video cable(not supplied) between the S-VIDEO OUT jack on DVD Recorder and S-VIDEO IN jack on your TV (or AV ampli er).

You will enjoy high quality images. S-Video separates the picture element into black and white (Y) and color (C) signals to present clearer images than regular video input mode. This connection outputs the 480i resolution to your TV.

Connect the audio cables(white and red) between the AUDIO OUT jacks on the DVD Recorder and AUDIO IN jacks on your TV(or AV ampli er). (See pages 23~25)

S-Video or Component video outputs are available only if your TV supports S-Video input or Component video input, respectively. If S-Video or Component video output does not work, check your TV connections and the TV input selection settings.

01378A-AR650-XAA-ENG.indb 21 2007-03-13 11:54:34

Co nn

ec tin

g & Se

ttin g U

p

English - 22

You will enjoy regular quality images. Connect the audio cables(white and red) between the

AUDIO OUT jacks on the DVD Recorder and AUDIO IN jacks on your TV(or AV ampli er). (See pages 23~25)

Connecting to a Video Input Jack Connect a video(yellow) cable between the VIDEO(yellow) OUT jack on DVD Recorder and VIDEO(yellow) IN jack on the TV (or AV ampli er).

01378A-AR650-XAA-ENG.indb 22 2007-03-13 11:54:35

Connecting & Setting Up

English - 23

Step 4 : Connecting the Audio Cable Select one of the Audio connections on the following pages.

Connecting to your TV This connection will use your TVs speakers.

01378A-AR650-XAA-ENG.indb 23 2007-03-13 11:54:37

Co nn

ec tin

g & Se

ttin g U

p

English - 24

Connecting to a Stereo Ampli er with Analog Input Jacks If your stereo ampli er only has AUDIO INPUT jacks(L and R), use the AUDIO OUT jacks on the recorder.

01378A-AR650-XAA-ENG.indb 24 2007-03-13 11:54:39

Connecting & Setting Up

English - 25

Connecting to an AV Ampli er with a Digital Input Jack If your AV ampli er has a Dolby Digital or DTS decoder and a digital input jack, use this connection. To enjoy Dolby Digital or DTS sound, you will need to set up the audio settings. (See page 38)

Manufactured under license from Dolby Laboratories. Dolby and the double-D symbol are trademarks of Dolby Laboratories.

DTS and DTS Digital Out are trademarks of DTS, Inc.

01378A-AR650-XAA-ENG.indb 25 2007-03-13 11:54:40

Co nn

ec tin

g & Se

ttin g U

p

English - 26

Step 5 : Connecting External Devices This allows you to connect your DVD Recorder to other external devices and view or record their outputs.

Connecting a VCR, Cable box/Satellite receiver (set top box) or DVD Player to the AV 1 IN or S-VIDEO IN Jacks

Connecting a VCR or external device to the AV 1 IN jacks of the DVD Recorder. You can record from connected equipment (VCR, STB or DVD Player).

You must also make audio connections when connecting via S-Video.

01378A-AR650-XAA-ENG.indb 26 2007-03-13 11:54:42

Connecting & Setting Up

English - 27

Connecting a Camcorder You can record from connected equipment, such as a camcorder by using the AV 2 IN or DV IN jacks on front of the DVD Recorder.

When an Input source is inserted into AV 2 while watching TV, the Input will be switched to AV 2 automatically. If the Input is not selected automatically, press the INPUT SEL. button on the remote control to select the DV Input. Check your camcorder's owner's manual to see how to use the camcorder in this mode.

(See page 49)

01378A-AR650-XAA-ENG.indb 27 2007-03-13 11:54:44

Sy st

em S

et up

English - 28

On-Screen Menu Navigation The on-screen menus allow you to enable or disable various functions on your DVD Recorder. Press the MENU button to open the on-screen menu and then use the following buttons to navigate through the on screen menus.

1. , Buttons Press these buttons on the remote control to move the selection bar , to cycle through the menu options.

2. ENTER Button Press this button on the remote control to con rm any new settings.

3. RETURN Button Press this button on the remote control to return to the Previous menu screen displayed or to exit the on-screen menu.

4. EXIT Button Press this button to exit the on-screen menu.

Plugging In & Auto Setup Your DVD Recorder will automatically set itself up when it is plugged in for the rst time. TV stations and clock will be stored in memory. The process takes a few minutes. Your DVD Recorder will then be ready for use.

1. Connect the RF(Antenna) cable to the TV as indicated on page 15. 2. Plug the DVD Recorder into the mains.

Auto in the front panel display ickers. 3. Press a number button to select the desired language. 4. Press a number button to select the desired Time Zone.

If the language for the startup screen is not set, the settings may change whenever you turn the power on or off. Therefore, make sure that you select the language you want to use.

System Setup

Press 1 for English Touche 2 pour Franais

Pulse 3 para Espaol

Timer RecordDVD-Recorder No Disc

Timer Record

Scheduled Record List

Timer Rec.

Setup

MOVE ENTER RETURN EXIT

Title ListDVD-Recorder DVD-RW(VR)

Title List

Playlist

Disc Manager

Timer Rec.

Setup

Title List

MOVE ENTER RETURN EXIT

Time Zone 1. Atlantic 2. Eastern 3. Central 4. Mountain 5. Pacific 6. Alaska 7. Hawaii

Select a time zone

01378A-AR650-XAA-ENG.indb 28 2007-03-13 11:54:46

System Setup

English - 29

Auto Clock Set This menu is used to set the current time. You need to set the time to use timer recording.

1. With the unit in Stop mode, press the MENU button. 2. Press the buttons to select Setup, then press the ENTER or

button. 3. Press the buttons to select Clock Set, then press the ENTER or button.

4. Press the buttons to select Auto Clock Set, then press the ENTER or button.

If your clock is set to the wrong time zone or daylight saving, you can adjust these settings without turning off the Auto Clock Set function.

Time Zone Press the buttons to select Time Zone, then press the ENTER or

button. Select the time zone of your area using the buttons, then press the ENTER or button.

If Time Zone is not set, Auto Clock Set & Daylight Saving function dose not work.

Daylight Saving Press the buttons to select Daylight Saving, then press the ENTER

or button. Select Automatic or No using the buttons, then press the ENTER or button.

Clock SetDVD-Recorder No Disc

Auto Clock Set

Manual Clock Set

Timer Rec.

Setup

MOVE ENTER RETURN EXIT

Auto Clock SetDVD-Recorder No Disc

Timer Rec.

Setup Time Zone

Daylight Saving

MOVE ENTER RETURN EXIT

Atlantic Eastern Central Mountain Paci c Alaska Hawaii

Auto Clock SetDVD-Recorder No Disc

Timer Rec.

Setup Time Zone : Eastern

Daylight Saving

MOVE ENTER RETURN EXIT

Automatic No

01378A-AR650-XAA-ENG.indb 29 2007-03-13 11:54:48

Sy st

em S

et up

English - 30

Manual Clock Set If your clock cannot be set automatically, set the clock manually.

1. With the unit in Stop mode, press the MENU button. 2. Press the buttons to select Setup, then press the ENTER or

button. 3. Press the buttons to select Clock Set, then press the ENTER or button.

4. Press the buttons to select Manual Clock Set, then press the ENTER or button.

5. Use the buttons to select the Current Date and Current Time, and then press the ENTER button. When the current time is stored in memory and then the set is powered off, the current time will appear in the front panel display. : Sets the value

You can set the value using the number buttons. : Moves to items

Auto Channel Memory You can set the Antenna/Cable TV channel settings automatically.

1. With the unit in Stop mode, press the MENU button. 2. Press the buttons to select Setup, then press the ENTER or

button. 3. Press the buttons to select Channel Set, then press the ENTER

or button. 4. Press the buttons to select Antenna/Cable TV, then press the

ENTER or button. Select the item that matches the antenna connection you selected on pages 15~16.

5. Select Antenna or Cable TV (depending on the hookup you chose) using the buttons, then press the ENTER or button.

6. Select Auto Channel Memory using the buttons, then press the ENTER or button. Auto Channel Memory (Analog) will be performed, then Auto Channel Memory (Digital) will be performed.

Press the RETURN or ENTER button to stop Auto Channel Memory. When memorizing Cable channels, it may take 6 times longer (about 50minutes) than when memorizing channels received over the air (antenna). Auto Channel Memory (Digital) cannot store scrambled channels.

Channel SetDVD-Recorder No Disc

Timer Rec.

Setup Antenna/Cable TV : Antenna

Auto Channel Memory

Channel Add/Delete

MOVE ENTER RETURN EXIT

Anten a Cable TV

Auto Channel Memory (Analog)

Total channel numbers : 05/69 Saved channel :

7%

Stop

Auto Channel Memory (Digital)

Total channel numbers : 04/69

5%

Stop

Manual Clock SetDVD-Recorder No Disc

Timer Rec.

Setup

MOVE ENTER RETURN EXIT

01 01 2007 12 00 AM

Month Day Year Hour Minute AM/PM

MON

01378A-AR650-XAA-ENG.indb 30 2007-03-13 11:54:51

System Setup

English - 31

Manual Channel Set Manual Channel Set can be used after you have rst performed Auto Channel Memory. Use the Manual Channel Setting to delete unnecessary channels.

1. With the unit in Stop mode, press the MENU button. 2. Press the buttons to select Setup, then press the ENTER or

button. 3. Press the buttons to select Channel Set, then press the ENTER

or button. 4. Press the buttons to select Channel Add/Delete, then press the

ENTER or button. 5. Press the or number buttons to select the channels you want to

add or delete on the Select channel screen. Then, press the ENTER button. Using CH ( ) buttons for channel selection allows the user to

add/delete one channel at a time. Using buttons for channel selection jumps to the next channel

memorized in Auto Channel Memory. 6. Press the buttons to select Add or Delete, then press the ENTER

button. The message Channel is added. or Channel is deleted. will be

displayed in the center of the screen. Continue to add or delete as many channels as you want to memorize

or delete. This can be used to add channels not stored automatically due to weak signal strength.

Press the RETURN button to return to the previous menu. Press the EXIT button to exit the menu.

Channel SetDVD-Recorder No Disc

Timer Rec.

Setup Antenna/Cable TV : Antenna

Auto Channel Memory

Channel Add/Delete

MOVE ENTER RETURN EXIT

Channel Add/DeleteDVD-Recorder No Disc

Timer Rec.

Setup Select channel : 2

Add Delete

ENTER RETURN EXITNUMBER0~9

01378A-AR650-XAA-ENG.indb 31 2007-03-13 11:54:53

Sy st

em S

et up

English - 32

Setting Up the System Options

Set Top Box Control If you have your cable box/satellite receiver(set top box) connected as shown on page 16, it can be controlled after setting up this menu.

1. With the unit in Stop mode/No Disc mode, press the MENU button on the remote control. Menu items differ depending on the disc type.

2. Select Setup using the buttons, then press the ENTER or button.

3. Select System using the buttons, then press the ENTER or button. System menu will be displayed.

4. Select Set Top Box Control using the buttons, then press the ENTER or button. Set Top Box Control menu will be displayed.

5. Select the desired sub menu(Control, Connection, CH Digit Lock, Mode for SET button, and Brand Code) using the buttons, then press the ENTER or button.

Control Select the sub item(Off or On) using the buttons, then press the ENTER button. Off : Turns off the cable box or satellite receiver (set top box) control

function. Select this if you do not want to use the supplied cable box controller (IR Blaster).

On : Turns on the cable box or satellite receiver (set top box) control function.

Connection Select the sub item (AV1, S-Video, CH3, CH4, AV2) using the buttons, then press the ENTER button. If you connect your cable box or satellite receiver (set top box) to the recorder's audio/video input. (page 16) AV1 : Select this when the cable box or satellite receiver (set top box) is

connected to the DVD recorder's AV 1 IN jacks. You can watch the output of the cable box or satellite receiver (set top box) connected to AV1 when the Recorder is powered off.

S-Video : Select this when the cable box or satellite receiver (set top box) is connected to the DVD recorder's S-Video IN jack. You can't select AV1 when the cable box or satellite receiver (set top box) is connected to the S-Video input.

AV2 : Select this when the cable box or satellite receiver (set top box) is connected to the DVD recorder's AV 2 IN jacks.

If you connect your cable box or satellite receiver (set top box) to the recorder's antenna input. (page 16) CH3 or CH4 : Select the output channel from CH3 or CH4 when the

cable box or satellite receiver (set top box) is connected to the DVD recorder's VHF/UHF IN jack.

See the instruction supplied with your cable box or satellite receiver (set top box) to con rm the box's antenna output channel.

SystemDVD-Recorder No Disc

Set Top Box Control

CM Skip Time : 15 Sec

EP Mode Time : 6 Hours

Chapter Creator : Off

Quick Recording : Off

Anynet+(HDMI-CEC) : On

Timer Rec.

Setup

MOVE ENTER RETURN EXIT

Set Top Box ControlDVD-Recorder No Disc

Timer Rec.

Setup Control : Off

Connection : CH3

CH Digit Lock : Off

Mode for SET button : Off

Brand Code : 0000

MOVE ENTER RETURN EXIT

Off On

Set Top Box ControlDVD-Recorder No Disc

Timer Rec.

Setup Control : Off

Connection : CH3

CH Digit Lock : Off

Mode for SET button : Off

Brand Code : 0000

MOVE ENTER RETURN EXIT

CH3 CH4 AV1 AV2

Set Top Box ControlDVD-Recorder No Disc

Timer Rec.

Setup Control : Off

Connection : CH3

CH Digit Lock : Off

Mode for SET button : Off

Brand Code : 0000

MOVE ENTER RETURN EXIT

CH3 CH4 AV1 AV2

01378A-AR650-XAA-ENG.indb 32 2007-03-13 11:54:55

System Setup

English - 33

CH Digit Lock Select the sub item(Off or Lock to two digits) using the buttons, then press the ENTER button. Off : Select this when your cable box or satellite receiver (set top box)

only accepts a three or more digit channel number. Normally select this. Lock to two digits : Select this when your cable box or satellite receiver

(set top box) only accepts a two digit channel number.

Mode for SET button Some cable boxes or satellite receivers (set top box) require you to press SET after pressing the channel number. If your cable box or satellite receiver (set top box) operates this way, follow the instructions below to set Mode 1 or 2. Select the sub item(Off, Mode 1 or Mode 2) using the buttons, then press the ENTER button. Select "Mode 1" or "Mode 2" if your cable box or satellite receiver requires pressing the SET button, after entering the channel number. Off : No code is sent when the SET button is pressed. Normally select this. Mode 1 or Mode 2 : Sends the channel number you entered.

If "Mode 1" does not work, try "Mode 2." If your cable box or satellite receiver (set top box) does not respond to either setting, contact the manufacturer.

Brand Code Enter the brand code of your cable box or satellite receiver (set top box) using the number buttons, then press the ENTER button. (See "Cable Box/Satellite Receiver Brand Code Table" on pages 81~83.)

If you cannot get the recorder to control your cable box/satellite receiver (set top box), check the connection and position of the IR Blaster cable. (page 16) If your cable box or satellite receiver still does not operate with this recorder, contact your cable company to see if they can provide you with a compatible cable box or satellite receiver. This menu may not work depending on your cable box or satellite receiver (set top box).

CM Skip Time Setting When a program recorded on a DVD-RAM, a DVD-RW, DVD-VIDEO or a DVD-R is played, the unit can be set to automatically skip a portion of the program corresponding to a CM(commercial) Skip Time set by the user.

1. With a disc inserted and the unit in Stop mode, press the MENU button on the remote control.

2. Select Setup using the buttons, then press the ENTER or button.

3. Select System using the buttons, then press the ENTER or button. System menu will be displayed.

4. Select CM Skip Time using the buttons, then press the ENTER or button. CM Skip Time will be displayed.

5. Select the desired time using the buttons, then press the ENTER or button.

6. If you press the CM SKIP button during playback, the section corresponding to the set time is skipped, and then the next section is played.

CM SKIP

Set Top Box ControlDVD-Recorder No Disc

Timer Rec.

Setup Control : Off

Connection : CH3

CH Digit Lock : Off

Mode for SET button : Off

Brand Code : 0000

MOVE ENTER RETURN EXIT

Off Lock to two digits

Set Top Box ControlDVD-Recorder No Disc

Timer Rec.

Setup Control : Off

Connection : CH3

CH Digit Lock : Off

Mode for SET button : Off

Brand Code : 0000

MOVE ENTER RETURN EXIT

Off Mode 1 Mode 2

Set Top Box ControlDVD-Recorder No Disc

Timer Rec.

Setup Enter the brand code of your set top box.

0 0 0 0

ENTER RETURN EXITNUMBER0~9

SystemDVD-Recorder No Disc

Timer Rec.

Setup

MOVE ENTER RETURN EXIT

Set Top Box Control

CM Skip Time : 15 Sec

EP Mode Time : 6 Hours

Chapter Creator : Off

Quick Recording : Off

Anynet+(HDMI-CEC) : On

15 Sec 30 Sec 60 Sec

01378A-AR650-XAA-ENG.indb 33 2007-03-13 11:54:57

Sy st

em S

et up

English - 34

CM Skip can be performed only during normal playback. When the time set is less than the remaining time of a current title: The next title is played from the beginning. When the time set is less than the remaining time of a playlist, the next scene is played. CM Skip does not work in a still picture mode. When a set time is less than the remaining time of a scene, last title, or last track that is currently displayed, a prohibition mark appears. CM Skip releases Repeat (including Repeat A-B, Chapter, and Title). CM Skip may not operate with some DVD-Video discs.

EP Mode Time Setting You can set the EP (Extended Play) record modes time to 6 or 8 hours.

1. With a disc inserted and the unit in Stop mode, press the MENU button on the remote control.

2. Select Setup using the buttons, then press the ENTER or button.

3. Select System using the buttons, then press the ENTER or button.

4. Select EP Mode Time using the buttons, then press the ENTER or button. EP Mode Time will be displayed.

5. Select the desired menu using the buttons, then press the ENTER or button.

Automatic Chapter Creation This function creates chapters(sections) within a title automatically. It works with DVD-RW (Video) and DVD-R discs only. 1. With a disc inserted and the unit in Stop mode, press the MENU button

on the remote control. 2. Select Setup using the buttons, then press the ENTER or

button. You can't use the Setup functions while playing a disc.

3. Select System using the buttons, then press the ENTER or button. System menu will be displayed.

4. Select Chapter Creator using the buttons, then press the ENTER or button. Chapter Creator items will be displayed.

5. Select On using the buttons, then press the ENTER button. Off : Select this option when you do not want to create chapters. On : Select this option when you want to create chapters.

SystemDVD-Recorder No Disc

Timer Rec.

Setup

MOVE ENTER RETURN EXIT

Set Top Box Control

CM Skip Time : 15 Sec

EP Mode Time : 6 Hours

Chapter Creator : Off

Quick Recording : Off

Anynet+(HDMI-CEC) : On

6 Hours 8 Hours

SystemDVD-Recorder No Disc

Timer Rec.

Setup

MOVE ENTER RETURN EXIT

Set Top Box Control

CM Skip Time : 15 Sec

EP Mode Time : 6 Hours

Chapter Creator : Off

Quick Recording : Off

Anynet+(HDMI-CEC) : On

Off On

01378A-AR650-XAA-ENG.indb 34 2007-03-13 11:55:00

System Setup

English - 35

Set the chapter creator to on and then start recording. Stopping the recording will automatically create a chapter menu. This function only works for normal recording. - After the recording has begun, the Do you want to create the chapter menu after this recording? message appears for 10 seconds. Select Yes or No. - Selecting Yes will create a new chapter menu while selecting No will not. - A new chapter is created according to the selected recording mode. A chapter will be about 5 minutes long in XP and SP, and about 15 minutes long in LP and EP mode.

To display the created chapters and nalize the disc, press the DISC MENU button. The chapters menu appears.

The Automatic Chapter Creation function does not work during Timer Recording or when you turn the power off.

Quick Recording Setting It takes about 10 seconds for a disc to load (initialize) every time you turn on the unit. To bypass this initialization process, you can set the Quick Recording feature to On. This enables you to record immediately without having to wait for the disc to load.

1. With a disc inserted and the unit in Stop mode, press the MENU button on the remote control.

2. Select Setup using the buttons, then press the ENTER or button.

3. Select System using the buttons, then press the ENTER or button. System menu will be displayed.

4. Select Quick Recording using the buttons, then press the ENTER or button. Quick Recording menu will be displayed.

5. Select On using the buttons, then press the ENTER or button.

The Quick Recording is set to Off as default. If the Quick Start Recording is set to On, the fan may continue to operate after the unit is shut off.

Anynet+(HDMI-CEC) Anynet+ is a function that can be used to operate the recorder using a Samsung TV remote control, by connecting the DVD Recorder to a SAMSUNG TV using an HDMI Cable. (see page 18) (This is only available with SAMSUNG TVs that support Anynet+.)

1. With the unit in Stop mode/No Disc mode, press the MENU button on the remote control.

2. Select Setup using the buttons, then press the ENTER or button. 3. Select System using the buttons, then press the ENTER or

button. The system menu will be displayed. 4. Select Anynet+(HDMI-CEC) using the buttons, then press the

ENTER or button. Anynet+(HDMI-CEC) items will be displayed.

5. Select On using the buttons, then press the ENTER or button.

SystemDVD-Recorder No Disc

Timer Rec.

Setup

MOVE ENTER RETURN EXIT

Set Top Box Control

CM Skip Time : 15 Sec

EP Mode Time : 6 Hours

Chapter Creator : Off

Quick Recording : Off

Anynet+(HDMI-CEC) : On

Off On

SystemDVD-Recorder No Disc

Timer Rec.

Setup

MOVE ENTER RETURN EXIT

Set Top Box Control

CM Skip Time : 15 Sec

EP Mode Time : 6 Hours

Chapter Creator : Off

Quick Recording : Off

Anynet+(HDMI-CEC) : On Off On

01378A-AR650-XAA-ENG.indb 35 2007-03-13 11:55:02

Sy st

em S

et up

English - 36

For using Anynet+(HDMI-CEC) 1. Connect the recorder to a Samsung TV with an HDMI cable.

(See page 18) 2. Set the Anynet+(HDMI-CEC) to On on your DVD Recorder.

(see above) 3. Set the Anynet+ function on your TV.

(See the TV instruction manual for more information.)

You can operate the DVD Recorder by using TV remote control. (TV buttons that can be used to control the DVD Recorder : , , ,

, and

buttons, ~ button)

When you press Anynet+ button on the TV's remote control, the OSD to the left will appear.

- DVDR Operation : Same as ANYKEY button ( ) on the DVD Recorder remote control.

- DVDR Menu : Same as MENU button ( ) on the DVD Recorder remote control.

By pressing the PLAY button of the recorder while watching TV, the TV screen will change to the play screen. If you play a DVD when the TV power is off, the TV will power On. If you turn the TV off, the DVD Recorder will power off automatically. (When the DVD recorder is recording, it can't be powered off.) If you change HDMI to other sources (Composite, Component, RF... etc) on your TV while playing a DVD disc, the DVD Recorder & VCR will stop playing. The DVD Recorder & VCR may keep playing certain discs based on their content.

Language Setting If you set the language options in advance, they will come up automatically every time you watch a movie.

1. With the unit in Stop mode/No Disc mode, press the MENU button on the remote control.

2. Select Setup using the buttons, then press the ENTER or button. 3. Select Language using the buttons, then press the ENTER or button.

The language setup menu will be displayed. 4. Select the sub menu (Audio, Subtitle, Disc Menu, On-Screen Menu,

Digital Caption Service, Digital Caption Setting) using the buttons, then press the ENTER or button. Audio : For the disc audio language. Subtitle : For the disc subtitles. Disc Menu : For the disc menu contained on the disc. On-Screen Menu : For the DVD recorder's menu. Digital Caption Service : For the Digital Caption Service type. Digital Caption Setting : For the Digital caption display options.

5. Select the desired language using the buttons, then press the ENTER or button.

If the selected language is not recorded on the disc, the default language on the disc is selected. The selected language will only appear if it is supported on the disc.

TV Menu

View TV

DVDR Menu

DVDR Operation

Receiver : Off

Setup

DVDR

Move Enter Exit

LanguageDVD-Recorder No Disc

Timer Rec.

Setup Audio : Off

Subtitle : CH3

Disc Menu : Off

On-Screen Menu : Off

Digital Caption Service :

Digital Caption Setting :

MOVE ENTER RETURN EXIT

Original

English Franais Deutsch Espaol Italiano Nederland Korean

01378A-AR650-XAA-ENG.indb 36 2007-03-13 11:55:04

System Setup

English - 37

Digital Caption You can modify and con gure how your captions will appear. The Digital Captioning function operates on digital channels only.

1. With the unit in Stop mode/No Disc mode, press the MENU button on the remote control.

2. Select Setup using the buttons, then press the ENTER or button. 3. Select Language using the buttons, then press the ENTER or button.

The language setup menu will be displayed. 4. Select Digital Caption Service using the buttons, then press the

ENTER or button. You can set the service type according to your environment. The available types are Service 1~6. You can also change Digital Caption Service by pressing Caption button on the remote control.

5. Select Digital Caption Setting using the buttons, then press the ENTER or button. You can set the following options: Character Size : You can set your Character size to Default, Small,

Standard and Large. Character Style : You can set your Character style among Default

and styles 0 through 7. Character Color : You can set the Character color of the text.

The available options are Default, White, Black, Red, Green, Blue, Yellow and Magenta.

Character Opacity : You can set the opacity of the text. The available options are Default, Solid, Translucent and Transparent.

Edge Color : You can set the Edge color of the text. The available options are Default, White, Black, Red, Green, Blue, Yellow and Magenta.

Edge Type : You can set the Edge type of the text. The available options are Non, Raised, Depressed, Outline, Left Shadow and Right Shadow.

Background Color : You can set the Background color of the text. The available options are Default, White, Black, Red, Green, Blue, Yellow and Magenta.

Background Opacity : You can set the Background opacity of the text. The available options are Default, Solid, Translucent and Transparent.

LanguageDVD-Recorder No Disc

Timer Rec.

Setup Audio : Original

Subtitle : CH3

Disc Menu : Off

On-Screen Menu : Off

Digital Caption Service :

Digital Caption Setting :

MOVE ENTER RETURN EXIT

Off Service 1 Service 2 Service 3 Service 4 Service 5 Service 6

Digital Caption SetDVD-Recorder No Disc

Timer Rec.

Setup Character Size : Default

Character Style : Default

Character Color : Default

Character Opacity : Default

Edge Color : Default

Edge Type : Default

MOVE ENTER RETURN EXIT

Digital Caption SetDVD-Recorder No Disc

Timer Rec.

Setup

Background Color : Default

Background Opacity : Default

MOVE ENTER RETURN EXIT

01378A-AR650-XAA-ENG.indb 37 2007-03-13 11:55:06

Sy st

em S

et up

English - 38

Setting Up the Audio Options You can connect the DVD-AR650 to an external audio ampli er or a Home Theater system. This allows you to setup the audio device and sound status settings depending on the audio system in use.

1. With the unit in Stop mode/No Disc mode, press the MENU button on the remote control.

2. Select Setup using the buttons, then press the ENTER or button.

3. Select Audio using the buttons, then press the ENTER or button.

4. Select the sub menu(Digital Output, DTS, Dynamic Compression) using the buttons, then press the ENTER or button.

Select the item that matches the audio connection youve selected on pages 23~35 (Method 1, 2 and 3).

Digital Output PCM : Converts to PCM(2CH) 48kHz audio.

Select PCM if your ampli er system is stereo and/or Dolby Prologic. Bitstream : Outputs Bitstream.

Select Bitstream if your ampli er system supports multi channel digital audio surround decoding such as Dolby Digital and/or DTS.

DTS Off : Doesnt output DTS bitstream. On : Outputs DTS bitstream. (via Digital Audio Output)

Select DTS when connecting to a digital amp with a DTS decoder. When DTS soundtrack is played, sound is not output from Analog Audio Output.

Dynamic Compression This is only active when a Dolby Digital signal is detected. Off : You can enjoy the movie with the standard DynamicRange. On : When movie soundtracks are played at low volume or from small

speakers, the system can apply appropriate compression to make low- level content more intelligible and prevent dramatic passages from getting too loud.

AudioDVD-Recorder No Disc

Timer Rec.

Setup Digital Output : PCM

DTS : Off

Dynamic Compression : On

MOVE ENTER RETURN EXIT

AudioDVD-Recorder No Disc

Timer Rec.

Setup Digital Output : PCM

DTS : Off

Dynamic Compression : On

MOVE ENTER RETURN EXIT

PCM Bitstream

AudioDVD-Recorder No Disc

Timer Rec.

Setup Digital Output : PCM

DTS : Off

Dynamic Compression : On

MOVE ENTER RETURN EXIT

Off On

AudioDVD-Recorder No Disc

Timer Rec.

Setup Digital Output : PCM

DTS : Off

Dynamic Compression : On

MOVE ENTER RETURN EXIT

Off On

01378A-AR650-XAA-ENG.indb 38 2007-03-13 11:55:08

System Setup

English - 39

Video(Display) Setting This allows you to set up the TV screen size settings.

TV Aspect 1. With the unit in Stop mode/No Disc mode, press the MENU button. 2. Select Setup using the buttons, then press the ENTER or button. 3. Select Video using the buttons, then press the ENTER or button. 4. Select TV Aspect using the buttons, then press the ENTER or button. 5. Select the desired item(4:3 Letter Box, 4:3 Pan-Scan or 16:9 Wide)

using the buttons. Then press the ENTER or button.

If you have a 4:3 standard TV 4:3 Letter Box : Select when you want to see the total 16:9 ratio screen

DVD supplies, even though you have a TV with a 4:3 ratio screen. Black bars will appear at the top and bottom of the screen.

4:3 Pan-Scan : Select this for a conventional size TV when you want to see the central portion of the 16:9 screen. (Extreme left and right side of movie picture will be cut off.)

If you have a wide screen TV or 4:3 standard TV with a wide-screen mode 16:9 Wide : You can view the full 16:9 picture on your widescreen TV.

When receiving a digital broadcast

Setting Value Source 16:9

16:9 (default)

16:9

4:3

4:3 (letter box or Pan& Scan)

16:9

4:3

- If you set the 4:3 ratio, the screen format will change automatically depending on the broadcast signal.

- If you set a different ratio from the one actually being broadcast, the picture be may be distorted (stretched or narrow).

Input Level Adjusts the level of the input signal. Darker : If you feel the screen is too light and you want to make the

screen darker. Lighter : If you feel the screen is too dark and you want to make the

screen lighter.

VideoDVD-Recorder No Disc

Timer Rec.

Setup TV Aspact : 16:9 Wide

Input Level : Darker

Black Level : 7.5 IRE

3D Noise Reduction : Off

HDMI/DVI Resolution : 480P

DivX(R) Registration

MOVE ENTER RETURN EXIT

4:3 Letter Box 4:3 P n-Scan 16:9 Wide

VideoDVD-Recorder No Disc

Timer Rec.

Setup TV Aspact : 16:9 Wide

Input Level : Darker

Black Level : 7.5 IRE

3D Noise Reduction : Off

HDMI/DVI Resolution : 480P

DivX(R) Registration

MOVE ENTER RETURN EXIT

Darker Lighter

01378A-AR650-XAA-ENG.indb 39 2007-03-13 11:55:11

Sy st

em S

et up

English - 40

Black Level Adjusts the black level of the screen. 0 IRE : Select this when you want a darker screen. 7.5 IRE : Select this when you want a lighter screen.

The Black level function is not available in the progressive scan mode. IRE: Short for the Institute of Radio Engineers. An IRE unit is a relative unit of measure equaling 1/140th of the peak-to-peak (p-p) video amplitude.

3D Noise Reduction Off : Normal On : Provides a cleaner picture through noise reduction (for recording).

HDMI/DVI Resolution This setting is used when the unit is connected by HDMI or DVI to Display devices (TV, projector, etc).

480p : 720 x 480 720p : 1280 x 720 1080i : 1920 x 1080 Connect the DVD-AR650 to your TV via HDMI or DVI. Set your TV's

input to HDMI or DVI. Press the P.SCAN button while the unit is in stop mode to select the

output resolution. - If your TV is connected via an HDMI or DVI cable, the output resolution

mode changes in the following sequence each time you press the P.SCAN button:

480p 720p 1080i.

- If the DVD Recorder is connected to your TV with Component cables(no HDMI/DVI cable connected), the output resolution mode toggles between 480p/480i.

DivX(R) Registration

Please use the Registration code to register your DVD Recorder with the DivX(R) Video On Demand format. To learn more, visit www.divx.com/vod

VideoDVD-Recorder No Disc

Timer Rec.

Setup TV Aspact : 16:9 Wide

Input Level : Darker

Black Level : 7.5 IRE

3D Noise Reduction : Off

HDMI/DVI Resolution : 480P

DivX(R) Registration

MOVE ENTER RETURN EXIT

480P 720P 1080i

VideoDVD-Recorder No Disc

Timer Rec.

Setup TV Aspact : 16:9 Wide

Input Level : Darker

Black Level : 7.5 IRE

3D Noise Reduction : Off

HDMI/DVI Resolution : 480P

DivX(R) Registration

MOVE ENTER RETURN EXIT

Your registration code is : XXXXXXXX

To learn more, visit www.divx.com/vod

OK

DivX(R) Vid o On Demand

VideoDVD-Recorder No Disc

Timer Rec.

Setup TV Aspact : 16:9 Wide

Input Level : Darker

Black Level : 7.5 IRE

3D Noise Reduction : Off

HDMI/DVI Resolution : 480P

DivX(R) Registration

MOVE ENTER RETURN EXIT

Off On

VideoDVD-Recorder No Disc

Timer Rec.

Setup TV Aspact : 16:9 Wide

Input Level : Darker

Black Level : 7.5 IRE

3D Noise Reduction : Off

HDMI/DVI Resolution : 480P

DivX(R) Registration

MOVE ENTER RETURN EXIT

0 IRE 7.5 IRE

01378A-AR650-XAA-ENG.indb 40 2007-03-13 11:55:13

System Setup

English - 41

Parental Control

The Parental Control function works in conjunction with DVDs that have been assigned a rating - which helps you control the types of DVDs that your family watches. There are up to 8 rating levels on a disc.

1. With the unit in Stop mode/No Disc mode, press the MENU button on the remote control.

2. Select Setup using the buttons, then press the ENTER or button. 3. Select Parental Control using the buttons, then press the ENTER or button.

4. The rst time the Parental Control is accessed, the Create the Password message will be displayed. Create a 4-digit password using the 0 to 9 buttons on the remote control.

5. The Con rm the password message will be displayed. Enter your password again using the 0 to 9 buttons on the remote control.

6. Press the ENTER or button, and then select On using the buttons. The Parental Control screen appears.

Setting the Rating Level 1. Select Rating Level using the buttons. 2. Press the ENTER or button. 3. Select the desired Level you want using the buttons, then press

the ENTER or button. For example, if you select up to Level 6, discs that contain Level 7, 8 will not play. A higher number indicates that the program is intended for adult use only.

Setting the Digital Rating You can set the rating level for Digital channels received by this unit.

1. Select Digital Rating using the buttons, then press the ENTER or button.

2. Press the button to select Digital Rating, then press the ENTER button. If information is not downloaded from the broadcasting station, the Digital Rating menu is deactivated. Parental restriction information is automatically downloaded while watching DTV channels. It may take several seconds. The Digital Rating menu is available for use after information is downloaded from the broadcasting station. However, depending on the information from the broadcasting station, it may not be available for use. Digital Rating Lock : select On using to use Digital rating. Downloadable U.S. Rating : select the rating title and the rating value. ex.)

The rating titles (for example: Humor Level..etc) and TV ratings (for example: DH,MH,H..etc) may differ depending on the broadcasting station. Clear All : select Yes to delete the downloaded data.

Parental ControlDVD-Recorder No Disc

Timer Rec.

Setup Password : 16:9 Wide

MOVE ENTER RETURN EXIT

Off On

Parental ControlDVD-Recorder No Disc

Timer Rec.

Setup Password : On

Rating Level : Level 8 Adults Digital Rating

Change Password

MOVE ENTER RETURN EXIT

Level 8 Adults Level 7 Level 6 Level 5 Level 4 Level 3 Level 2 Level 1 Kids

Parental ControlDVD-Recorder No Disc

Timer Rec.

Setup Password : On

Rating Level : Level 8 Adults Digital Rating

Change Password

MOVE ENTER RETURN EXIT

Digital RatingDVD-Recorder No Disc

Timer Rec.

Setup Digital Rating Lock : On

Downloadable U.S. Rating

Clear All

MOVE ENTER RETURN EXIT

Digital RatingDVD-Recorder No Disc

Timer Rec.

Setup Digital Rating Lock : On

Downloadable U.S. Rating

Clear All

MOVE ENTER RETURN EXIT

Digital RatingDVD-Recorder No Disc

Timer Rec.

Setup Humor Level

Intrlligence Level

MOVE ENTER RETURN EXIT

Humor LevelDVD-Recorder No Disc

Timer Rec.

Setup DH MH - H - VH - EH -

MOVE ENTER RETURN EXIT

01378A-AR650-XAA-ENG.indb 41 2007-03-13 11:55:16

Sy st

em S

et up

English - 42

You can independently lock the ratings. The locked ratings are indicated by the symbol ( ). To unlock a locked rating, press the ENTER button again. Parental restriction levels differ depending on the broadcasting station. The rating titles (For example : Humor level..etc) and values (For example : DH,MH..etc) are changed depending on the downloaded information. Generally, the Digital Broadcast parental lock system uses the U.S. or Canadian Rating region Table (RRT). It is same as V-Chip system for Analog Broadcasts.

Changing the Password 1. Select Change Password using the buttons. 2. Press the ENTER or button.

The Enter the password message will be displayed. 3. Enter the 4-digit password using the 0 to 9 buttons on the remote control. 4. The Con rm the password message will be displayed.

Enter your password again using the 0 to 9 buttons on the remote control.

If you forgot your password, remove the disc. Press the CH ( / ) buttons on the front panel of the DVD Recorder simultaneously for 5 seconds or more when the power is on. All settings including the password will revert to the factory settings.

EPG-Electronic Program Guide The electronic program guide gives you information on available programs.

1. Press the EPG button while you are viewing a program. (DTV) RED button (Timer Record) : Setting the Timer Record or delete.

GREEN button (Scroll Up) : Scrolls up through the guide. YELLOW button (Scroll Down) : Scrolls down through the guide.

BLUE button (Full/Mini Guide) : Toggles between the Full/Mini Guide. (l)button : Goes to next day (l)button : Goes to previous day ENTER button (Information) : View the detail information or change

the channel 2. Press the buttons to select the desired channel, then press

the ENTER button.

The EPG function does not support digital cable. Only digital off-air (antenna) channels are supported.

Parental ControlDVD-Recorder No Disc

Timer Rec.

Setup Password : On

Rating Level : Level 8 Adults Digital Rating

Change Password

MOVE ENTER RETURN EXIT

01:35 am WED. 01/31/2007 Full Guide D 7-1 KBS D-2

00:59 am ~ 01:49 am

Today 01:30 am 02:00 am 02:30 am D 7-1 KBS D-2 D 9-1 KBS D-2 D 10-1 KBS D-2 D 11-1 KBS D-2

MOVEINFO/ PREV/NEXT DAY EXIT

Timer Record Scroll up Scroll down Mini Guide

01378A-AR650-XAA-ENG.indb 42 2007-03-13 11:55:19

System Setup

English - 43

Viewing Full Guide and Mini Guide The Full Guide will display programming information for your current channel.

Press the BLUE button to see the Mini Guide. If you press this button again, you can return the Full Guide.

Full Guide When moving within the Channel table The channel/sub picture and EPG information of selected channel is

updated by moving up/down.

Only the currently selected screen information will be displayed on the EPG screen. A speci c channel must be selected to see updated information on that channel.

When moving within the Time Table 1. Press the buttons to select desired Program Title. 2. Then press Enter button. If the Program Title you have highlighted

matches the channel in the sub-picture, you will see detailed program information. If it does not match, pressing Enter will change the channel rst. You must then press Enter again to see the detailled Program info.

The channel does not change in the sub picture when navigating within the Time Table. You must use the Channel table or press Enter after selecting a Program Title.

EPG information is not updated. A maximum of 5 days worth of Program information can be viewed.

Mini Guide Press the ENTER button to see the program information.

If you press channel up/down button, you can exit EPG screen automatically.

EPG Timer Recording Make sure that clock is set before operating this function. (see page 28)

1. Press the EPG button in Digital Channel mode. 2. Press the buttons in the Channel table to select the Channel for

recording 3. Press the buttons in the Time Table to select the desired

Program Title for recording 4. Then press TIMER (RED) button. Timer Rec. is setup. 5. If you want to cancel the TIMER REC. for that program, press one more time.

You can check this setting scheduled List. (see page 52) (Up to 12 recordings can be set for both EPG and regular TV) You can change the recording speed. (But you can not change the Date,Time,Source in EPG Recording Mode) The time information in the EPG Guide is send from current channel being broadcast.

If the TV Station sends the wrong time information, Timer recording will fail or the wrong program will be recorded. If there is more than 10 minute gap between the current EPG time information and the setting time on this unit, EPG Timer Recording does not work.

Mini Guide

Scheduled Record ListDVD-Recorder DVD-RW(VR) Current Time 12:03 AM

No. Source Date Start End Mode Edit

Recordable Time : 01:59 SP

No. 01

Source Date Start End Mode

AV 1 01/01 12:03 AM 02:03 AM SP

Recordable Time : 01:59 SP

MOVE ENTER RETURN EXIT

01:35 am WED. 01/31/2007 Full Guide D 7-1 KBS D-2

00:59 am ~ 01:49 am

Today 01:30 am 02:00 am 02:30 am D 7-1 KBS D-2 D 9-1 KBS D-2 D 10-1 KBS D-2 D 11-1 KBS D-2

MOVEINFO/ PREV/NEXT DAY EXIT

Timer Record Scroll up Scroll down Mini Guide

REC

Full Guide

01:35 am WED. 01/31/2007 Full Guide D 7-1 KBS D-2

00:59 am ~ 01:49 am

Today 01:30 am 02:00 am 02:30 am D 7-1 KBS D-2 D 9-1 KBS D-2 D 10-1 KBS D-2 D 11-1 KBS D-2

MOVEINFO/ PREV/NEXT DAY EXIT

Timer Record Scroll up Scroll down Mini Guide

01:35 am WED. 01/31/2007 Full Guide D 7-1 KBS D-2

00:59 am ~ 01:49 am

Today 01:30 am 02:00 am 02:30 am D 7-1 KBS D-2 D 9-1 KBS D-2 D 10-1 KBS D-2 D 11-1 KBS D-2

MOVEINFO/ PREV/NEXT DAY EXIT

Timer Record Scroll up Scroll down Mini Guide

01:35 am WED.

Today 01:30 am D 7-1 KBS D-2 D 9-1 KBS D-2 D 10-1 KBS D-2 D 11-1 KBS D-2

Timer Record

/ PREV/NE

(Channel table)

(Time Table)

(Sub picture)

D 7-1 KBS D-2 01:36 am WED. 01/31/2007

To day 00:59 am

To day 01:49 am

To day 02:59 am

Timer Record Full Guide

INFO/ PREV/NEXT DAY EXITMOVE

01378A-AR650-XAA-ENG.indb 43 2007-03-13 11:55:22

Re co

rd in

g

English - 44

This section explains various DVD recording methods.

This unit can record on various types of discs. Before recording, read the following instructions and select the disc type according to your preference.

Recordable discs This recorder can record on the following types of discs.

DVD-RAM DVD-RW DVD-R

DVD-RWs and DVD-RAMs are rewritable. DVD-Rs are non-rewritable

Compatibility between Samsung and Other manufacturer's Recorders Disc

Types Recording

format Recording

Device Finalizing Additional Recording in Samsung Recorder

DVD-RAM VR Mode Samsung X Recordable

Other Company X Recordable

DVD-RW

VR Mode Samsung

nalized Not recordable not nalized Recordable

Other Company nalized Not recordable

not nalized Recordable

V Mode Samsung

nalized Not recordable not nalized Recordable

Other Company nalized Not recordable

not nalized Not recordable

DVD-R V Mode Samsung

nalized Not recordable not nalized Recordable

Other Company nalized Not recordable

not nalized Not recordable

Finalize - This closes the DVD-R/-RW and no additional recording can be

done. Un nalize - This allows additional recording on a DVD-RW disc originally recorded on the DVD-AR650. - A DVD-RW disc that has been recorded by DAO(Disc At once) in a PC cannot be un nalized. - A DVD-RW disc that has been recorded in Video Mode of another manufacturer's recorder cannot be un nalized. - A DVD-R disc cannot be un nalized.

Recording

01378A-AR650-XAA-ENG.indb 44 2007-03-13 11:55:25

Recording

English - 45

Recording Formats Since available functions differ depending on the disc type, select a disc that best ts your preference. When you insert an unused disc, the following message appears.

DVD-RAM : Use after formatting the disc. DVD-RW : Use after initializing the disc.

You can change the VR or V mode of DVD-RW disc. Refer to Formatting a Disc on page 76.

DVD-R : Formatting disc is unnecessary.

DVD-RAM/-RW(VR mode) This mode involves multiple editing functions (such as deletion of the

whole title, partial deletion of a title, etc.). Various editing options using a created Playlist.

DVD-RW(Video mode)/-R Chapters will be created automatically when you nalize recording on

DVD-R/DVD-RW discs in Video mode. Simple editing (erasing titles/changing title name).

You can initialize discs automatically using EZ REC MODE. (See page 54)

NoYes

Unformatted Disc Do you want to format this disc?

DVD-RAM

NoYes

Uninitalized Disc Do you want to initialize this disc?

DVD-RW

01378A-AR650-XAA-ENG.indb 45 2007-03-13 11:55:26

Re co

rd in

g

English - 46

Recording Mode Select one of four record modes by pressing the REC MODE button repeatedly for the desired recording time and picture quality while the unit is in Stop mode. In general, picture quality improves as the recording time decreases. In FR mode, the most suitable record mode is selected automatically according to the remaining time on the disc and length of the timer recording set. You can select only one mode from XP, SP, LP and EP for timer recording.

Mode Characteristic Recording Times Data Rates

XP (high quality mode)

Select when the video quality is important.

Approx. 1 hour about 8 Mbps

SP (standard quality mode)

Select to record in standard quality.

Approx. 2 hours about 4 Mbps

LP (long recording mode)

Select when a long recording time is required.

Approx. 4 hours about 2 Mbps

EP (extended mode)

Select when a longer recording time is required.

Approx. 6 hours/ about 1.2 Mbps Approx. 8 hours/ about 0.8 Mbps

FR (Flexible Recording)

For timer recording only see page 52.

Approx 1 to 8 hours Approx 0.8 to 8Mbps

Dual layer DVD-Rs have approximately double the capacity of single layer DVD-Rs. (See page 55.)

Unrecordable Video Video with copy protection cannot be recorded on this DVD Recorder. When the DVD Recorder receives a copy guard signal while recording, recording stops and the following message appears on the screen.You cannot record copy protected movie.

01378A-AR650-XAA-ENG.indb 46 2007-03-13 11:55:27

Recording

English - 47

Concerning Copy Control Signals

TV broadcasts that contain copy control signals may have one of the following three signal types, Copy-Free, Copy-Once and Copy-Never. If you want to record a copy-once type program, use a DVD-RW disc with CPRM in VR Mode. You can also use DVD-RAM discs.

('O' : Supported, '-' : Not Supported)

Signal type Media Copy-Free Copy-Once Copy-Never

DVD-RAM (Ver.2.0) O O* -

DVD-RW (Ver.1.1) O - - DVD-RW (Ver.1.1) with CPRM VR mode O O* - DVD-R O - -

When a Copy Once recording has been made, recording cannot be done anymore. *compatible with CPRM.

Content Protection for Recordable Media (CPRM) CPRM is a mechanism that ties a recording to the media on which it is recorded. It is supported by some DVD recorders, but not by many DVD players. Each blank recordable DVD has a unique 64-bit media ID etched in the BCA(Burst Cutting Area). When protected content is recorded onto the disc, it can be encrypted with a 56-bit C2 (Cryptomeria) cipher derived from the media ID. Disc contents cannot be copied to other media.

About the INFO Button The INFO function allows you to view the current status and progress of playback and recording. When recording on a used disc, make sure that there is enough disc space for recording.

Press the INFO button. The disc information display window appears. Disc Type Current information display status Disc Name Total Title : Total number of titles Total Playlist : Total number of Playlists Recordable Time : The longest continuous recording time in each of the record modes(approximate) Date : Current date Time : Current time

Items in the display differ depending on the disc type or the recording format. With DVD-RAMs or DVD-RWs, you can free up disc space by erasing titles. Press the INFO button again with the unit in playback or recording mode, then you can check the current status.

DVD-RW(VR) Disc Info Disc Name Disc Total Title 15 Total Playlist 1 Recordable Time 02: 12 SP Protection Not Protected Screen AV1 JAN 01 2007 MON 12:00 AM

01378A-AR650-XAA-ENG.indb 47 2007-03-13 11:55:29

Re co

rd in

g

English - 48

Recording immediately

Before you start

Check that the disc has enough available space for the recording. Adjust the recording mode.

1. Press the OPEN/CLOSE button and place a recordable disc on the disc tray.

2. Press the OPEN/CLOSE button to close the disc tray. Wait until "LOAD" disappears from the front panel display. If an unused DVD-RW disc is inserted, the message Uninitialized Disc Do you want to initialize this disc? will appear. (See page 45)

Recording the current TV program you are watching 1. Press the CH ( / ) or number ( ~ ) buttons to select the

current program you want to record. 2. Press the REC MODE button repeatedly, (or press the REC MODE button

and then press the button) to select the recording speed (quality). SP LP EP XP

3. Press the REC button. Information concerning the channel is displayed on the screen and then recording begins. Icon( ) is displayed on the front panel.

Recording from External Equipment

1. Press the INPUT SEL. button to select the input source according to the connection you made. The front panel display changes in the following sequence:

AV1 AV2 DV CH D-CH

2. Press the REC MODE button repeatedly, to select the recording speed(quality).

SP LP EP XP

3. Press the REC button.

To pause recording Press the REC PAUSE button to pause a recording in progress. Press the REC PAUSE button again to resume recording.

To stop recording Press the STOP ( ) button to stop or nish recording in progress. When using DVD-RAM/DVD-RW/DVD-R discs, the message Updating

the information of disc. Please wait for a moment. is displayed.

Recording : AV1

Record Mode XP (01:11)

Record Mode XP (01:11)

01378A-AR650-XAA-ENG.indb 48 2007-03-13 11:55:31

Recording

English - 49

You can not change the recording mode and input source during recording. Recording will stop automatically if there is no free space left. Up to 99 titles can be recorded onto a DVD-RAM/-RW/-R disc. Recording will stop automatically if a copy protected image is selected. If you are using a Cable Box(no antenna), you cannot watch a different cable TV program from the one you're recording. DVD-RAM/DVD-RW discs must be formatted before starting to record. Most new discs are sold unformatted. Do not use DVD-R authoring discs with this unit.

Copying from a Camcorder You may control a Digital Camcorder using the IEEE1394 (DV) interface.

Before you start Check that the disc has enough available space for the recording. Adjust the record mode. See page 27 to see how to connect the camcorder to your DVD recorder.

1. Press the OPEN/CLOSE button, and place a recordable disc on the disc tray.

2. Press the OPEN/CLOSE button to close the disc tray. Wait until LOAD disappears from the front panel display.

3. Press the REC MODE button repeatedly to select the recording speed(quality).

SP LP EP XP

4. Press the INPUT SEL. button to select DV. If the input is set to DV, a playback/record menu that enables Digital camcorder control appears on the top of the screen.

5. Select the PLAY ( ) icon on the upper part of the screen to playback the camcorder and nd the starting position to copy.

6. To start recording, select REC( ) icon in the top side of the screen using the buttons, then press the ENTER button.

To stop recording Press the STOP ( ) button to stop or nish recording in progress. When using DVD-RAM/DVD-RW/DVD-R discs, the message Updating

the information of disc. Please wait for a moment is displayed.

You can not change the record mode and input source while recording. Recording will stop automatically if there is no free space left. Up to 99 titles can be recorded onto a DVD-RAM/-RW/-R disc. DVD-RAM/DVD-RW discs must be formatted before starting to record. Most new discs are sold unformatted. Do not use DVD-R authoring discs with this unit. To access on-screen controls during recording, press the or buttons. When copying from a camcorder and the end of the recorded content is reached (no Video), the screen may turn blue or purple. IEEE1394 : A very fast external bus standard that supports data transfer rates of up to 400Mbps (in 1394a) to transfer high levels of data in real-time, such as video devices.

DV

The DV device is connected

MOVE SELECT RETURN

Record Mode XP (01:11)

01378A-AR650-XAA-ENG.indb 49 2007-03-13 11:55:33

Re co

rd in

g

English - 50

Making a One Touch Recording (OTR)

You can set the DVD Recorder to record in preset increments by pressing the REC button repeatedly. 1. If you want to record from a connected external component, press the

INPUT SEL. button to select an appropriate external input (AV1, AV 2 or DV, CH, D-CH).

2. Press the REC button to start recording. 3. Press the REC button to adjust the recording time.

0:30 1:00 1:30 2:00 3:00 4:00 off

The timer counter decreases to 0:00, then the DVD Recorder stops recording. After nishing recording, the DVD Recorder will turn off automatically.

To stop recording Press the STOP( ) button. The message Press STOP button once more to cancel Timer Record. is displayed. Press the STOP( ) button again to stop recording.

01378A-AR650-XAA-ENG.indb 50 2007-03-13 11:55:35

Recording

English - 51

Setting a Timer Recording

You need to set the Clock (Setup Clock Set) before proceeding with a timer recording. (See page 29) 1. Press the OPEN/CLOSE button, and place a recordable disc on the

disc tray. 2. Press the OPEN/CLOSE button to close the disc tray.

Wait until LOAD disappears from the front panel display. If an unused DVD-RW disc is inserted, whether to initialize or not will be asked rst. (See page 45)

3. Press the MENU button in Stop mode. 4. Press the buttons to select Timer Rec., and then press the

ENTER or button. 5. Press the buttons to select Timer Record, and then press the

ENTER or button. The Timer Record Input items are displayed. You can also set a timer recording via the TIMER button.

6. Fill in the items using the buttons. : Moves to the previous/next item, or 0~9 : To set or change items in the Scheduled Record List Menu. Source: Select the video input source (AV 1, AV 2, CH, D-CH) you

want to make a timer recording of. Date: Date that the timer recording starts

- There are three options when setting the date. See below: To make a recording on a speci c date, press the or number

buttons until the date you want appears. To make a recording at the same time every day (Monday to Friday),

press the buttons until MON-FRI appears. To make a recording on a speci c day of the week (ie Mon, Tues etc),

press the buttons until 'Every SAT'...'Every SUN' appears. Start/End Time: Start and end time of the timer recording Mode (Record mode)

XP : Approx. 1 hour SP : Approx. 2 hours LP : Approx. 4 hours EP : Approx. 6 hours or 8 hours FR : See page 51.

When you are recording at EP mode on a DVD-RW(V)/-R disc, it may not record the full 6 or 8 hours because the unit uses the VBR(Variable Bit Rate) ENCODING system. For example, if you record a Program with a lot of action, it uses a higher bit rate which in turn consumes more disc memory.

7. Press the ENTER button. ( ) and Timer Set will appear on the front panel display. This means

that a timer recording is set. Recording is automatically performed when the set time is reached.

Source Date Start End Mode

AV 1 01/01 12:03 AM 02:03 AM SP

No. 01

Recordable Time : 01:59 SP

No. 01 Source Date Start End Mode

AV 1 MON-FRI 12:03 AM 02:03 AM SP

Recordable Time : 01:59 SP

No. 01 Source Date Start End Mode

AV 1 Every SUN 12:03 AM 02:03 AM SP

Recordable Time : 01:59 SP

Scheduled Record ListDVD-Recorder DVD-RW(VR) Current Time 12:03 AM

No. Source Date Start End Mode Edit

Recordable Time : 01:59 SP

No. 01

Source Date Start End Mode

AV 1 01/01 12:03 AM 02:03 AM SP

Recordable Time : 01:59 SP

MOVE ENTER RETURN EXIT

Scheduled Record ListDVD-Recorder DVD-RW(VR) Current Time 12:03 AM

No. Source Date Start End Mode Edit

01 AV 1 01/ 01 05:00 AM 07:00 AM SP

02 / : :

Recordable Time : 01:59 SP

MOVE ENTER RETURN EXIT

Timer RecordDVD-Recorder DVD-RW(VR)

Title List

Playlist

Disc Manager

Timer Rec.

Setup

Timer Record

Scheduled Record List

MOVE ENTER RETURN EXIT

01378A-AR650-XAA-ENG.indb 51 2007-03-13 11:55:36

Re co

rd in

g

English - 52

If the timer settings overlap The rst program has priority. After recording of the rst program is complete, the second program starts being recorded. The timer recording time may differ from the set time depending on the disc and the overall timer recording status (for example, recording times overlapping, or when the previous recording ends within 3 minutes of the start of the next recording.)

will start blinking if Timer Recording is not ready to start.

Flexible Recording (for Timer Recording only)

In FR mode, the most suitable recording mode is selected automatically, according to the remaining time on the disc and the length of the timer recording set. The FR mode recording setup is the same as Timer Recording setup. When setting the Rec mode in step 6, select FR Mode. (See page 51)

Editing the Scheduled Record List

You can change timer record settings using the scheduled record list menu.

1. Press the MENU button in STOP mode. 2. Press the buttons to select Timer Rec., and then press the

ENTER or button. 3. Press the buttons to select Scheduled Record List, and then

press the ENTER or button. 4. Press the buttons to select the number of the Scheduled Record

List you want to edit, and then press the ENTER or button. The Edit and Delete items are displayed.

5. Press the buttons to select Edit, and then press the ENTER or button. The Timer Record Input item is displayed. Edit the items you want to modify. See the Timer Record section for more information on Timer Record Input items. (See page 50)

6. Move through the items with the buttons and change the settings with or number buttons and press the ENTER button.

7. Press the EXIT button after the operation is nished. The menu screen will disappear.

Scheduled Record ListDVD-Recorder DVD-RW (VR) Current Time 12:03 AM

No. Source Date Start End Mode Edit

Recordable Time : 01:59 SP

01 AV 1 01/ 01 05:00 AM 07:00 AM SP

02 AV 1 01/ 03 12:06 AM 02:06 AM SP

03 / : :

MOVE ENTER RETURN EXIT

Edit Delete

Scheduled Record ListDVD-Recorder DVD-RW(VR) Current Time 12:03 AM

No. Source Date Start End Mode Edit

01 AV 1 01/ 01 05:00 AM 07:00 AM SP

02 / : :

Recordable Time : 01:59 SP

MOVE ENTER RETURN EXIT

01378A-AR650-XAA-ENG.indb 52 2007-03-13 11:55:38

Recording

English - 53

Deleting the Scheduled Record List

You can delete timer record list using the scheduled record list menu. 1. Press the MENU button in Stop mode. 2. Press the buttons to select Timer Rec., and then press the

ENTER or button. 3. Press the buttons to select Scheduled Record List, and then

press the ENTER or button. 4. Press the buttons to select the number of the timer recording you

want to delete, and then press the ENTER or button. The Edit and Delete items are displayed.

5. Press the buttons to select Delete, and then press the ENTER or button. 6. Press the buttons to select Yes, and then press the ENTER button.

The selected entry will be deleted from the list.

You can not delete programs that are currently being recorded.

Recording the Scheduled Record List When the start time in the Scheduled Record List is reached while the unit is powered off, the unit will automatically power on and start recording.

1. When the scheduled recording is operating, the program being recorded will not display on TV. Power on TV using the TV remote control. Power off TV using the TV remote control if you dont want to see the

program being recorded.

To stop recording Press the STOP ( ) button. The message Press STOP button once more to cancel Timer Record. is displayed. Press the STOP ( ) button again to stop recording.

If a copy protection signal is received during recording, recording will stop. If there is no free disc space or the disc is not recordable, recording will not operate. (You can record after replacing the disc.)

Press STOP button once more to cancel Timer Record.

You cannot record copy protected movie.

Scheduled Record ListDVD-Recorder DVD-RW (VR) Current Time 12:03 AM

No. Source Date Start End Mode Edit

01 CH 11 01/ 01 05:00 AM 07:00 AM SP

02 CH 7 01/03 12:06 AM 02:06 AM SP

03 / : :

Recordable Time : 01:59 SP

Do you want to delete No.01?

Yes No

No. 01

MOVE ENTER RETURN EXIT

01378A-AR650-XAA-ENG.indb 53 2007-03-13 11:55:40

Re co

rd in

g

English - 54

EZ REC MODE

This function allows you to Initialize and Finalize a disc automatically.

1. With the unit in Stop/No Disc mode, press the EZ REC MODE button on the remote control.

2. Press the buttons to select On, and then press the ENTER button. The EZ REC MODE is set up.

3. Insert a disc. If the disc is new, it will initialize automatically.

4. Press the REC button. 5. EZ REC MODE will Automatically Finalize the disc under the following

conditions. After the disc is nalized, it will play in most DVD players/drives.

- When you press the OPEN/CLOSE button on your DVD Recorder after recording on at least 30% of the disc. The tray will open after the disc has been nalized.

- When the disc is full, it will nalize automatically and the Recorder will remain in stop mode.

- When you make a timer recording and it occupies at least 30% of the disc, the disc will nalize automatically and the Recorder will power off. Please note that auto nalization will not work if the Recorder has more than one Timer Recording set in the Scheduled Record List.

If you insert a new DVD-RW disc, it will be formatted in V mode after auto initializing. If you select off, you must initialize (see page 45) and nalize the disc manually in the Disc Manager menu.(see page 77) The length of Recording is different according to recording mode. (see page 46)

50%

Disc Finalize Processing..

50%

Disc Initialize (DVD-V) Now, initializing..

Press On to confirm EZ REC mode. Otherwise press Off

On Off

01378A-AR650-XAA-ENG.indb 54 2007-03-13 11:55:42

English - 55

Playback

Playback This section introduces basic playback functions and playback by disc type.

Read the following information before playing a disc.

Region code (DVD-Video only) Both the DVD recorder and the discs are coded by region. These regional codes must match in order for the disc to play. If the codes do not match, the disc will not play. The Region Number for this recorder is described on the rear panel of the recorder.

Logos of Discs that can be played

Disc types that can be played Disc

Types Disc Logo

Recorded content Disc Shape Max. Playing Time

DVD- VIDEO

VIDEO AUDIO

Single sided(5) 240min Double sided(5) 480min Single sided(3.5) 80min Double sided(3.5) 160min

AUDIO- CD AUDIO

Single sided(5) 74min Single sided(3.5) 20min

JPEG JPEG Images

Single sided(5) - Single sided(3.5) -

MP3 MP3 Audio

Single sided(5) - Single sided(3.5) -

MPEG4 MPEG4 Movie

Single sided(5) - Single sided(3.5) -

DVD- RAM

VIDEO AUDIO

Single sided(5) (4.7GB)

1hr (XP: Excellent Quality) 2hrs (SP: Standard Quality) 4hrs (LP: Long Playback) 6 or 8hrs (EP:Extended)

Double sided(5) (9.4GB)

2hr (XP: Excellent Quality) 4hrs (SP: Standard Quality) 8hrs (LP: Long Playback) 12 or 16hrs (EP:Extended)

DVD-RW VIDEO AUDIO 5 (4.7GB)

1hr (XP: Excellent Quality) 2hrs (SP: Standard Quality) 4hrs (LP: Long Playback) 6 or 8hrs (EP:Extended)

DVD-R VIDEO AUDIO

Single Layer(5) (4.7GB)

1hr (XP: Excellent Quality) 2hrs (SP: Standard Quality) 4hrs (LP: Long Playback) 6 or 8hrs (EP:Extended)

Dual Layer(5) (8.5GB)

2hr (XP: Excellent Quality) 4hrs (SP: Standard Quality) 8hrs (LP: Long Playback) 11 or 15hrs (EP:Extended)

D I G I T A L Dolby Digital DTS Digital Audio

Stereo NTSC broadcast system in U.S.A, Canada, Korea,

Japan,etc.

MP3DivX

01378A-AR650-XAA-ENG.indb 55 2007-03-13 11:55:43

English - 56

Pl ay

ba ck

Discs That Cannot be Played DVD-Video with a region number other than 1 or ALL 5 2.6 GB and 5.2 GB DVD-RAM 3.9 GB DVD-R Disc for Authoring. A DVD-R/DVD-RW(V) disc which has been recorded and not nalized in

a different manufacturer's recorder. PAL discs DVD-ROM/PD/MV-Disc, etc. Video CD/CVD/SVCD/CD-ROM/CDV/CD-G/CD-I

This DVD recorder can only operate with discs that are compatible with DVD-RAM Standard Version 2.0. Playback and/or recording may not work for some types of discs, or when speci c operations, such as angle change and aspect ratio adjustment, are being performed. Information about the discs is written in detail on the box. Please refer to this if necessary. Do not allow the disc to become dirty or scratched. Fingerprints, dirt,dust,scratches or deposits of cigarette smoke on the recording surface may make it impossible to use the disc for recording. DVD-RAM/-RW/-R discs may not be able to play on some DVD players, depending on the player, disc and the condition of the recording. Discs with PAL programs already recorded on them can not be recorded on using this product.

Playing a Disc 1. Press the OPEN/CLOSE button.

The tray opens. 2. Place a disc gently into the tray with the discs label facing up.

For DVD-RAM discs, insert the printed side facing up. 3. Press the OPEN/CLOSE button to close the disc tray.

Your DVD Recorder closes the disc tray and loads the disc automatically. When the recorder is powered on and a disc is in the tray, the unit will

be activated and wait in Stop mode. Press the PLAY( ) button to start playback. If you want the unit to play automatically when it is powered off with a

disc in the unit, power on with the PLAY( ) button. 4. Press the STOP( ) button to stop playback.

When you stop playing the disc, the recorder remembers where you stopped. When you press the PLAY button again, it will pick up where you left off. (unless the disc is removed, the recorder is unplugged, or if you do not press the STOP button twice.) This function is only applicable to DVD-VIDEO, DVD-RAM, DVD-RW, DVD-R or audio CDs (CD-DA).

Do not move your DVD recorder while playing, as this may cause damage to the disc. Make sure to press the OPEN/CLOSE button to open or close the disc tray. Do not push the disc tray while it is being opened or closed, as this may cause a product malfunction. Do not place foreign materials on or in the disc tray. Some functions may perform differently or be disabled depending on the disc type. If this occurs, refer to the instructions written on the disc case. Be especially careful that children's ngers are not caught between the disc tray and the tray chassis when it closes. You must only insert one DVD disc at a time. Inserting two or more discs will not allow playback and may cause damage to the DVD player.

01378A-AR650-XAA-ENG.indb 56 2007-03-13 11:55:45

English - 57

Playback

Using the Disc Menu & Title Menu Some discs contain a dedicated menu system that allows you to select special functions for the title, such as chapters, audio track, subtitles, lm previews, information on characters, etc.

For DVD-VIDEO Discs

Disc Menu : Press the DISC MENU button to enter the disc's menu. Move to the setup menu related to the playback operation. You can select the audio language and the subtitles provided by the disc. Title Menu : Press the TITLE MENU button to move to the title menu of the disc. Use this button if the disc contains more than one title. Some type of

discs may not support the title menu function.

For DVD-RAM/DVDRW/R Discs

Title List : Press the TITLE LIST button. The Title List is simply a list of titles on a disc. If a title is deleted, that title cannot be played again.

PLAY LIST : Press the PLAY LIST button. A playlist is a custom-made list of titles. When one playlist is played, only the titles within the playlist will play and then stop. Even if that playlist is deleted, the original recording will not be deleted. (only VR mode)

Using the Playback Related Buttons

Searching through a Chapter or Track

DVD-VIDEO/ DVD-RAM/ DVD-RW/DVD-R

Fast 1(X 2) Fast 2(X 4) Fast 3(X 8) Fast 4(X16) Fast 5(X 32) Fast 6(X128) Fast 1(X 2)

MPEG4 Fast 1 Fast 2 Fast 3 Fast 1

AUDIO CD (CDDA)

Fast 2 Fast 4 Fast 8 Fast 2

During playback, press the SEARCH( ) button on the remote control. You can scan the program in reverse. Press and hold the SEARCH( ) button, playback is done at the

default speed of fast 2. If you release the SEARCH( ) button, playback is performed at

normal speed.(Except CD-DA) To return to normal playback speed, press the PLAY( ) button.

01378A-AR650-XAA-ENG.indb 57 2007-03-13 11:55:47

English - 58

Pl ay

ba ck

No sound is heard during Scan(Search) mode except 'Fast 1' search mode (X1.7 speed audio). For CD(CD-DA), You can hear sound during Scan mode. You cannot hear audio while scanning an MPEG4. The speed marked while scanning may be different from the actual playback speed.

Searching Chapters or Tracks During playback, press the SKIP( ) button on the remote control. If you press the SKIP( ) button, it moves to the beginning of the

chapter or track or marker (DVD-RAM,DVD-RW(VR mode).) Pressing the button once again within 3 seconds returns to the beginning of the previous chapter or track or marker (DVD-RAM, DVD-RW(VR mode).)

If you press the SKIP( ) button, it moves to the next chapter or title or marker (DVD-RAM,DVD-RW (VR mode).)

Slow Motion Play

In Pause mode, press the SEARCH( ) button on the remote control. If you press the SEARCH( ) button, Slow 1 Slow 2 Slow 3

If you press the SEARCH( ) button, Slow 1 Slow 2 Slow 3

Press and hold the SEARCH( ) button during pause, and the disc will play slowly at a 1/2 speed. If the button is released, the pause operation will resume.

To return to normal speed playback, press the PLAY( ) button.

The speed marked in this function may be different from the actual playback speed. Slow motion operates only in the forward direction on MPEG4 discs.

Step Motion Play

Press the STEP( ) button on the remote control in the still mode. Each time the button is pressed, a new frame will appear.

If you press the STEP( ) button, the previous frame will be activated. If you press the STEP( ) button, the next frame will be activated.

To return to normal speed playback, press the PLAY( ) button.

Step motion operates only in the forward direction on MPEG4 discs.

01378A-AR650-XAA-ENG.indb 58 2007-03-13 11:55:50

English - 59

Playback

Using the ANYKEY Button The ANYKEY function allows you to easily search for a desired scene by accessing title, chapter, track, and time. You can also change the subtitle and audio settings and set some features including Repeat, Angle, and Zoom.

Moving to a Desired Scene Directly

If you want to move to a certain title, chapter or time use this function.

1. Press the ANYKEY button during playback. 2. Press the buttons to select the Title, Chapter or Time. 3. Press the buttons or number (0~9) buttons to select the desired

scene and then press the ENTER button. In case of searching a time, Enter the time in the sequence of hours, minutes, seconds using the number buttons. are not available.

The Time Search function does not operate with some discs. To make the screen disappear, press the ANYKEY again.

Playing Repeatedly 1. Press the ANYKEY button during playback. 2. Press the buttons to select Repeat and press the buttons to

select the Title or Chapter you want to play repeatedly. 3. Press the ENTER button.

DVD-RAM, DVD-RW(VR mode), un nalized DVD-R and un nalized DVD-RW (Video mode) do not repeat a chapter.

Playing a Certain Section Repeatedly

1. Press the ANYKEY button during playback. 2. Press the buttons to select Repeat and press the button to

select A-B. 3. Press the ENTER button. 4. Press the ENTER button at the point where you want the repeat play to

start (A) and press it again at the point where you want the repeat play to stop (B). Repeat playback of the A-B section starts.

If you set point (B) before ve seconds has lapsed, the prohibition mark ( ) will appear. You can also activate Normal Playback by pressing the CANCEL button. Audio CDs(CD-DA) and MP3 discs do not support the Repeat A-B function.

DVD-VIDEO Title

Chapter

Time

Subtitle

Audio

Repeat

Angle

Zoom

1/2 1/20 00:00:00 Off ENG D 2CH Off 1/3 Off

MOVE CHANGE

DVD-VIDEO

MOVE SELECT

Title

Chapter

Time

Subtitle

Audio

Repeat

Angle

Zoom

1/2

1/20 00:01:05 Off ENG D 2CH Title 1/3 Off

DVD-VIDEO

MOVE SELECT

Title

Chapter

Time

Subtitle

Audio

Repeat

Angle

Zoom

1/2 1/20 00:01:05 Off ENG D 2CH A-B 1/3 Off

01378A-AR650-XAA-ENG.indb 59 2007-03-13 11:55:54

English - 60

Pl ay

ba ck

Selecting the Subtitle

Subtitle languages may not work depending on the disc type. This is only available during playback. 1. Press the ANYKEY button during playback. 2. Press the buttons to select Subtitle and press the buttons to

select the desired subtitle language.

If the subtitles overlap, disable the caption function on your TV. Some discs allow you to select the language for the disc menu only. To make the screen disappear, press the ANYKEY again.

Selecting the Audio language

Audio languages may not work depending on the disc type. This is only available during playback. 1. Press the ANYKEY button during playback. 2. Press the buttons to select Audio and press the buttons to

select the desired audio language.

Audio languages may be different because they are disc-speci c. Some discs allow you to select the audio language for the disc menu only. To make the screen disappear, press the ANYKEY again.

Using One Touch button By pressing the Audio button, you can access the Audio function directly.

Changing the Camera Angle

When a DVD-VIDEO contains multiple angles of a particular scene, you can select the Angle function. This is only available during playback. If the disc contains multiple angles, the ANGLE mark appears on the screen. 1. Press the ANYKEY button during playback. 2. Press the buttons to select Angle and press the buttons or

number(0~9) buttons to select the desired angle.

This function is disc-dependent, and may not work all DVDs. This function does not work when a DVD has not been recorded with a multicamera angle system. To make the screen disappear, press the ANYKEY again.

DVD-VIDEO

MOVE CHANGE

Title

Chapter

Time

Subtitle

Audio

Repeat

Angle

Zoom

1/2 1/20 00:00:10 Off ENG D 2CH Off 1/3 Off

DVD-VIDEO

MOVE CHANGE

Title

Chapter

Time

Subtitle

Audio

Repeat

Angle

Zoom

1/2 1/20 00:00:10 Off ENG D 2CH Off 1/3 Off

DVD-VIDEO

MOVE CHANGE

Title

Chapter

Time

Subtitle

Audio

Repeat

Angle

Zoom

1/2 1/20 00:00:11 Off ENG D 2CH Off 1/3 Off

01378A-AR650-XAA-ENG.indb 60 2007-03-13 11:55:57

English - 61

Playback

Zooming-In

1. Press the ANYKEY button during playback or pause. 2. Press the buttons to select Zoom, and then press the ENTER

button. ( ) will be displayed.

3. Press the buttons to move to the area you want to enlarge. 4. Press the ENTER button.

normal size 2X 4X 2X normal size

Using Bookmarks

This feature lets you bookmark sections of a DVD or DVD-R/-RW (V mode), so you can quickly nd them.

Setting Bookmarks 1. Press the MARKER button during playback. 2. Press the MARKER button during playback. Press the ENTER button

when the desired scene appears. The number 1 is displayed and the scene is memorized.

3. Press the button to move to the next position. 4. Press the ENTER button when the desired scene appears.

The number 2 is displayed and the scene is memorized. Repeat above to bookmark other positions. You can bookmark up to 10 scenes.

When the disc tray is opened and then closed, bookmarks will disappear. The button display may differ depending on the disc type.

Playing Back a Bookmark 1. Press the MARKER button during playback. 2. Press the buttons to select a bookmarked scene. 3. Press the ENTER or PLAY( ) button to start playing from the

selected scene.

(V mode)

MOVE PLAY CANCEL RETURN

Bookmark 1 2 - - - - - - - --

MOVE PLAY CANCEL RETURN

Bookmark 1 2 - - - - - - - --

01378A-AR650-XAA-ENG.indb 61 2007-03-13 11:55:59

English - 62

Pl ay

ba ck

Clearing a bookmark 1. Press the MARKER button during playback 2. Press the buttons to select a bookmarked scene. 3. Press the CANCEL button to delete the selected bookmark.

Using Markers

Setting Markers 1. Press the MARKER button during playback. 2. Press the ENTER button when the desired scene appears.

The number 01 is displayed and the scene is memorized. 3. Press the button to move to the next position. 4. Press the ENTER button when the desired scene appears.

The number 02 is displayed and the scene is memorized. DVD-RAM or DVD-RW (VR Mode) discs have the Marker function

instead of the Bookmark function. The Marker function allows you to mark up to 99 scenes. Since the scenes may be displayed as many different pages, numbering is necessary. If a disc in use is encoded with Disc Protect, Markers cannot be set or deleted. Only playback is available.

Playing Back a Marker 1. Press the MARKER button during playback. 2. Press the buttons to select a bookmarked scene. 3. Press the ENTER or PLAY( ) button to start playing from the

selected scene. If you press the SKIP( ) button, it moves to the beginning of

the marker. Pressing the button once again within 3 seconds returns to the beginning of the previous marker.

If you press the SKIP( ) button, it moves to the next marker.

Clearing a Marker 1. Press the MARKER button during playback. 2. Press the buttons to select a bookmarked scene.

Press the CANCEL button to delete the selected bookmark. When a marker is cleared while DVD-RAM/DVD-RW(VR mode) is

playing, marker numbers will change. For example, if the 7th marker is cleared after ten markers are registered, the marker numbers after the eighth will automatically move ahead by one and the 8th marker becomes the 7th.

(VR mode)

MOVE SELECT RETURN

Bookmark 1 2 - 4 5 6 - - - --

MOVE PLAY CANCEL RETURN

Marker 01 02 -- -- -- -- -- -- -- -- N : 2

MOVE PLAY CANCEL RETURN

Marker 01 02 -- -- -- -- -- -- -- -- N : 2

MOVE PLAY CANCEL RETURN

Marker 01 02 03 04 05 06 07 08 09 10 N : 10

Marker 01 02 03 04 05 06 07 08 09 -- N : 9

01378A-AR650-XAA-ENG.indb 62 2007-03-13 11:56:02

English - 63

Playback

Playing an Audio CD/MP3

Buttons on the Remote Control Used for CD Playback : Selects a track (song). : Plays the selected track (song). ENTER( ) button : Plays the selected track (song). RETURN( ) button: Moves to the folder to which the current song belongs. SKIP( ) button : Plays the next track. SKIP( ) button : Returns to the beginning of the current track when pressed during playback. If pressed again, your DVD recorder moves to and plays the previous track. If you press this button within three seconds after playback starts, the previous track will be played. If you press this button after three seconds, the current track will be replayed from the beginning.

SEARCH( / ) button : Fast Play (X2, X4, X8) STOP( ) : Stops a track(song). PLAY/PAUSE( ) : Plays a track(song) or pauses playback. ANYKEY: To select the sub menu on screen display (Repeat or Play Option).

Playing an Audio CD(CD-DA) 1. Insert an audio CD (CD-DA) into the disc tray.

The audio CD menu appears and the tracks (songs) are played automatically.

2. Press the buttons to select the track you want to hear, and then press the ENTER button or button.

Audio CD(CD-DA) Screen Elements PLAY MODE icon Current track (song) : Displays the number of the track currently being played. Displays the current play index and total track number. Shows the operating state of a disc and the current playback time. Displays the track list (song list) and the playing time of each track. Button display.

Music ListCD

PLAY MODE MOVE ENTER EXITRETURN

No. Title Length

TRACK 1 01/15

001 TRACK 1 00:03:50 002 TRACK 2 00:04:00 003 TRACK 3 00:03:49 004 TRACK 4 00:03:47 005 TRACK 5 00:04:29 006 TRACK 6 00:03:44 007 TRACK 7 00:03:44

0:00:01

TRACK 1 CDDA

Music ListCD

001 TRACK 1 00:03:50 002 TRACK 2 00:04:00 003 TRACK 3 00:03:49 004 TRACK 4 00:03:47 005 TRACK 5 00:04:29 006 TRACK 6 00:03:44 007 TRACK 7 00:03:44

No. Title Length

TRACK 1 01/15

0:00:01 TRACK 1

PLAY MODE MOVE ENTER EXITRETURN

CDDA

01378A-AR650-XAA-ENG.indb 63 2007-03-13 11:56:05

English - 64

Pl ay

ba ck

Playing an MP3 Disc 1. Insert an MP3 disc into the disc tray.

Press the buttons to select Disc Navigation, and then press the ENTER or button.

2. Press the buttons to select Music, and then press the ENTER or button. The MP3 menu appears and the tracks(songs) are played automatically.

3. Press the buttons to select the track (song) you want to hear, and then press the ENTER button or button.

MP3 Screen Elements PLAY MODE icon Current track (song) : Displays the name of the track being played. MP3 le information. Shows the operating state of a disc and the current playback time. Displays the information for the folder and its tracks. Button display.

Playing Repeatedly

1. Press the ANYKEY button during playback. The play mode window appears.

2. Select the desired repeat mode using buttons, and then press the ENTER button. Track :Selected track is played repeatedly. Disc : Inserted disc is played repeatedly. Folder(mp3 only) : Tracks in the current folder are played

repeatedly. To return to normal playback 3. Press the CANCEL button to return to normal playback.

Music ListMP3

PLAY MODE MOVE ENTER EXITRETURN

No. Title

SONGO1 01/11

SONGO1 3.5MB 2004/08/26

0:00:15

ROOT 001 SONGO1 002 SONGO2 003 SONGO3 004 SONGO4 005 SONGO5 006 SONGO6MP3

Music ListMP3

PLAY MODE MOVE ENTER EXITRETURN

No. Title

SONGO1 01/11

SONGO1 3.5MB 2004/08/26

0:00:11

ROOT 001 SONGO1 002 SONGO2 003 SONGO3 004 SONGO4 005 SONGO5 006 SONGO6MP3

001 TRACK 1 00:03:50 002 TRACK 2 00:04:00 003 TRACK 3 00:03:49 004 TRACK 4 00:03:47 005 TRACK 5 00:04:29 006 TRACK 6 00:03:44 007 TRACK 7 00:03:44

0:00:20

CDDA

TRACK 1

Music ListCD

PLAY MODE Repeat : Off

Play option : Normal

PLAY MODE MOVE ENTER EXITRETURN

No. Title Length

TRACK 1 01/15

01378A-AR650-XAA-ENG.indb 64 2007-03-13 11:56:09

English - 65

Playback

Play Option Mode

1. During Stop, Press the ANYKEY button. The Play option will be highlighted. During Playback, Repeat Mode will be highlighted.

2. Select a desired play option (Normal, Random, Intro or Playlist) using the buttons. Press the ENTER button. Normal : Tracks on a disc are played in the order in which they were

recorded on the disc. Random[R] : The Random option plays the discs tracks in random

order. After a random list is generated and played completely, another random list is generated and played. Random Play is continued until the play option is changed.

Intro[ I ] : The rst 10 seconds of each track will be played. If you want to listen to the music that you have selected, press the ENTER button or PLAY( ) button. The play option will be changed to Normal Play. When Intro Play is completed, Normal Play is performed.

Playlist : The Playlist playback option allows you to select the order in which you want tracks to play.

To Program Tracks

You can register a maximum of 30 tracks in the playlist. 1. During Stop, Press the ANYKEY button.

The Play option will be highlighted. During Playback, Repeat Mode will be highlighted.

2. Select Playlist using the buttons, and then press the ENTER button. The Playlist screen will appear. Select tracks in the order in which you want them to play using the buttons. Press the ENTER button. If there is a track on your playlist you wish to remove. Press the button, then press the buttons to select the track you wish to remove, then press the CANCEL button. The selected track will be removed.

3. Press the PLAY( ) button to playback the playlist.

Playing a Picture CD 1. Insert an JPEG disc into the disc tray. 2. Press the buttons to select Disc Navigation, and then press the

ENTER or button. 3. Press the buttons to select Photo, and then press the ENTER or button.

4. Press the buttons to select a picture. To see the next 8 pictures, press the SKIP( ) button. To see the previous 8 pictures, press the SKIP( )button.

Music ListCD

PLAY MODE EXIT

001 TRACK 1 00:03:50 002 TRACK 2 00:04:00 003 TRACK 3 00:03:49 004 TRACK 4 00:03:47 005 TRACK 5 00:04:29 006 TRACK 6 00:03:44 007 TRACK 7 00:03:44

No. Title Length

TRACK 1 01/15

CDDA

TRACK 1

0:00:01

PLAY MODE Repeat : Off

Play option : Normal

MOVE ENTER RETURN

Music ListCD

001 TRACK 1 00:03:50 002 TRACK 2 00:04:00 003 TRACK 3 00:03:49 004 TRACK 4 00:03:47 005 TRACK 5 00:04:29 006 TRACK 6 00:03:44 007 TRACK 7 00:03:44

PLAY MODE MOVE ENTER EXITRETURN

No. Title Length

TRACK 1 01/15

CDDA

TRACK 1 0:00:01

PLAY MODE Repeat : Off

Play option : Normal

PlaylistCD 07/15

001 TRACK 1 002 TRACK 3 003 TRACK 4 004 TRACK 7

TRACK 1 TRACK 2 TRACK 3 TRACK 4 TRACK 5 TRACK 6 TRACK 7 TRACK 8

PLAY MODE MOVE ENTER EXIT

CDDA

CDDA

CDDA

CDDA

CDDA

CDDA

CDDA

CDDA

Photo ListJPEG

JPEG01 1/08

ROOT JPEG01 JPEG02 JPEG03

JPEG04 JPEG05 JPEG06 JPEG07

Slide Show MOVE ENTER RETURN EXIT

01378A-AR650-XAA-ENG.indb 65 2007-03-13 11:56:11

English - 66

Pl ay

ba ck

5-1. If you press the PLAY( ) button, the Slide show screen will appear. The picture interval (Slide show speed) must be set.

5-2. Press the ENTER button with a picture selected in the Album screen and select a display mode (Album screen ( ), Slide show ( ), Rotation ( ) or Zoom ( )) using the buttons, then press the ENTER button. : Returns to the Album screen. : The unit enters slide show mode. Before the slide show can begin, the picture interval (Slide show speed) must be set.

: Each time the ENTER button is pressed, the picture rotates 90 degrees clockwise.

: Each time the ENTER button is pressed, the picture is enlarged up to 4X. (Normal 2X 4X 2X Normal)

Press the ANYKEY button to display or clear menus.

Playing an MPEG4 Disc

An MPEG4 File is used to contain audio and video data.

1. Insert a MPEG4 Disc into the disc tray. 2. Press the buttons to select the Disc Navigation, and then press

the ENTER or button. 3. Press the buttons to select the DivX, and then press the ENTER

or button. 4. Press the buttons to select the avi le (DivX), then press the

ENTER, or PLAY button. 5. When an MPEG4 le is being played, you can use the following functions.

Pressing the STOP button once during playback will display the le list, pressing the button again will exit the menu screen.

MPEG4 Function Description Function Description

Skip Scene During playback, press the SKIP ( or ) button, it moves forward or backward 5 minutes.

Search Scene During playback, press the SEARCH ( or ) button and press again to search at a faster speed. (Fast1, Fast2, Fast3)

Slow Motion In pause or step mode, press the SEARCH ( ) button on the remote control. (Slow1, Slow2, Slow3)

Step Motion Press the STEP( ) button on the remote control in still mode.

This DVD Recorder can play the following video compression formats, -MPEG4 Codec format :DivX 3.11 DivX 4.x DivX 5.x -Audio format :.MP3,.MPEG,.PCM,.AC3,.DTS Supported subtitle le formats:.smi,.srt,.sub,.psb, .txt (The subtitle le should have exactly the same name to corresponding MPEG4 le name) Some MPEG4 les created on a personal computer may not be able to be played back. This is why Codec Type,Version and Higher resolutions over speci cation are not supported.

DVD-RW(VR)

Slide Show Speed

Slow Fast

MOVE PHOTO ENTER RETURN

JPEG01

Normal

DVD-RW(VR)

JPEG01

MOVE PHOTO ENTER RETURN

DivX ListCD

ROOT

No. Title Size

ROOT 00/02

MPEG4

ROOT 001 DIVX01 70.8MB 002 DIVX02 73.6MB

MOVE ENTER RETURN EXIT

01378A-AR650-XAA-ENG.indb 66 2007-03-13 11:56:15

English - 67

Playback

Playing the Title List

Follow these instructions to play back a scene from the Title List.

1. Press the TITLE LIST button. The Title List screen is displayed. You can also use the MENU button. Press the MENU button. Press the buttons to select Title List, and then press the

ENTER or button twice. 2. Press the buttons to select Title.

Press the PLAY button. The selected entry (title) will be played back. Press the ENTER or button. The Edit menu is displayed on the right.

(Rename, Delete, Edit, Protection : See pages 68~70) 3. To stop playing the title, press the STOP( ) button.

To return to the title list screen, press the TITLE LIST button.

Title List Screen Elements

Playback screen for recorded entries

Information window for the selected entry : Title name, recording date, lock status, record mode

Recorded entry No.

Recorded entry title

Recording length (i.e., the playing time) Title list edit items Play : Plays the selected entry. Rename : Renames the title of a selected entry. Delete : Deletes the selected entry from the list. Edit : Deletes a section. Protection : Locks or unlocks the selected entry.

Button display

By pressing the ANYKEY button, you can play the desired title. This may depend on the the disc type. DVD-R/DVD-RW(Video) has limited editing function.(See page 44)

Title ListDVD-RW(VR)

01 APR/19/2007 12:00 00:00:21 02 APR/19/2007 12:30 00:00:03 03 APR/20/2007 12:00 00:00:15 04 APR/20/2007 12:30 00:00:16 05 APR/21/2007 12:00 00:06:32 06 APR/21/2007 12:30 00:08:16

No. Title Length Edit

APR/19/2007 1/6

APR/19/2007 12:00 AM AV1 APR/19/2007 SP

MOVE ENTER RETURN EXIT

APR/21/2007 12:00 PR12

APR/21/2007

SP

APR/21/2007

01 APR/19/2007 12:00 00:00:21 02 APR/19/2007 12:30 00:00:03 03 APR/20/2007 12:00 00:00:15 04 APR/20/2007 12:30 00:00:16 05 APR/21/2007 12:00 00:06:32 06 APR/21/2007 12:30 00:08:16

No. Title Length Edit 5/6

APR/21/2007 12:00 AM AV1 APR/21/2007 SP

APR/21/2007

Title ListDVD-RW(VR)

MOVE ENTER RETURN EXIT

Title ListDVD-RW(VR)

01 APR/19/2007 12:00 00:00:21 02 APR/19/2007 12:30 00:00:03 03 APR/20/2007 12:00 00:00:15 04 APR/20/2007 12:30 00:00:16 05 APR/21/2007 12:00 00:06:32 06 APR/21/2007 12:30 00:08:16

No. Title Length Edit

5/6

APR/21/2007 12:00 AV1

APR/21/2007

SP

APR/21/2007

Play Rename Delete Edit Protection

MOVE ENTER RETURN EXIT

01378A-AR650-XAA-ENG.indb 67 2007-03-13 11:56:20

Ed iti

ng

English - 68

Editing This section introduces basic functions of DVD editing. Title List

A title is a section of recorded video and audio. The Title List shows a list to help you select a title. If one title is deleted from the title list, that title cannot be played again.

Playlist This refers to a unit of playback, which is made by selecting a desired scene in the entire Title List. When one playlist is played, only the scene selected by the user will play and then stop. Since only the information necessary for playing a desired scene is included in a playlist, even if that playlist is deleted, the original recorded title will not be deleted.

Recording or editing might not be completed if an error such as a sudden power failure occurs. Please be aware that material that has been damaged cannot be retrieved.

Basic Editing (Title List)

Renaming (Labeling) a Title

Follow these instructions to rename a title list entry, i.e., to edit the title of a recorded program. 1. Press the TITLE LIST button. The Title List screen is displayed. You can also use the MENU button.

Press the MENU button. Press the buttons to select Title List, and then press the ENTER

or button twice. 2. Press the buttons to select an entry you want to rename from the

Title List, and then press the ENTER or button. 3. Press the buttons to select Rename, and then press the ENTER

or button. The Rename screen is displayed.

4. Select the desired characters using the buttons, press the ENTER button. Back Space : Deletes the character before the cursor. Space : Enters a blank and moves the cursor one forward (to the

right). Delete : Deletes the character at the cursor position.

Clear : Deletes all the character inputs. Save : Registers the character inputs. The maximum number of characters that can be entered is 31. All 31

characters can be displayed by pressing the INFO button twice. 5. Press the buttons to select Save, and then press the ENTER

button. The changed title name is displayed on the title item of the selected Title list entry.

Rename

Back Space Space Delete Clear

Save

Sports(A1)

DVD-RW(VR)

DVD-Recorder

MOVE ENTER RETURN EXIT

Title ListDVD-RW(VR) Sports(A1)

Sports(A1) APR/03/2007 SP

5/6

No. Title Length Edit 01 APR/19/2007 12:00 00:00:21 02 APR/19/2007 12:30 00:00:03 03 APR/20/2007 12:00 00:00:15 04 APR/20/2007 12:30 00:00:16 05 Sports(A1) 00:06:32 06 APR/21/2007 12:30 00:08:16

MOVE ENTER RETURN EXIT

01378A-AR650-XAA-ENG.indb 68 2007-03-13 11:56:23

Editing

English - 69

Locking (Protecting) a Title

Follow these instructions to lock an entry to protect it from accidental deletion. 1. Press the TITLE LIST button. The Title List screen is displayed. You can also use the MENU button.

Press the MENU button. Press the buttons to select Title List, and then press the ENTER

or button twice. 2. Press the buttons to select an entry you want to protect from the

Title List, and then press the ENTER or button. 3. Press the buttons to select Protection, and then press the

ENTER or button. 4. Press the buttons to select On, and then press the ENTER

button. The lock icon on the information window for the selected entry changes to the locked status. ( ) If you want to unlock the title entry, select the protected title and set the Protection function to Off.

Deleting a Title

Follow these instructions to delete an entry from the Title List. 1. Press the TITLE LIST button. The Title List screen is displayed. You can also use the MENU button.

Press the MENU button. Press the buttons to select Title List, and then press the ENTER

or button twice. 2. Press the buttons to select an entry you want to delete from the

Title List, and then press the ENTER or button. 3. Press the buttons to select Delete, and then press the ENTER or button. You will be prompted with the con rmation message. DVD-RAM, DVD-RW(VR mode): Since Playlist is present, the message Do you want to delete?(Related playlists may be deleted.) is displayed. DVD-RW(Video mode), DVD-R: Since Playlist is not present, the message Do you want to delete? is displayed. The message may be different depending on the type of disc.

4. Press the buttons to select Yes, and then press the ENTER button.

You cannot delete a protected entry. If you want to delete a protected entry, select Off in the Title Protection menu. Once an entry is deleted from the Title List, it cannot be recovered. Once a DVD-R or DVD-RW is nalized, it cannot be deleted. With DVD-R, titles are only deleted from the menu, however, the Title remains physically on the disc.

Title List Sports(A1) 5/6

Sports(A1) APR/21/2007 SP

NoYes

Do you want to delete? (Related playlists may be deleted.)

DVD-RW(VR)

MOVE ENTER RETURN EXIT

Title ListDVD-RW(VR)

01 Drama 00:00:21

02 Music 00:00:03

03 Sports 00:00:15

04 Movie 00:00:16

05 Sports(A1) 00:06:32

06 Edu 1 00:08:16

No. Title Length Edit

Sports(A1) 5/6

Sports(A1) APR/21/2007 SP

Play Rename Delete Edit Protection

MOVE ENTER RETURN EXIT

Title ListDVD-RW(VR)

No. Title Length Edit

Sports(A1) 5/6

Sports(A1) APR/21/2007 SP

01 Drama 00:00:21

02 Music 00:00:03

03 Sports 00:00:15

04 Movie 00:00:16

05 Sports(A1) 00:06:32

06 Edu 1 00:08:16

MOVE ENTER RETURN EXIT

Title List Sports(A1) 5/6

Sports(A1) APR/21/2007 SP

OffOn

Title Protection:

DVD-RW(VR)

MOVE ENTER RETURN EXIT

01378A-AR650-XAA-ENG.indb 69 2007-03-13 11:56:25

Ed iti

ng

English - 70

Deleting a Section of a Title

Follow these instructions to delete a section of a Title List entry. 1. Press the TITLE LIST button. The Title List screen is displayed. You can also use the MENU button.

Press the MENU button. Press the buttons to select Title List, and then press the ENTER

or button twice. 2. Press the buttons to select an entry you want to edit from the Title

List, and then press the ENTER or button. 3. Press the buttons to select Edit, and then press the ENTER or

button. 4. Press the ENTER button at the starting point.

The image and starting point time are displayed on the section deletion starting point window.

5. Press the ENTER button at the end point. The image and end point time are displayed in the Section deletion ending point window.

6. Press the buttons to select Delete, and then press the ENTER button. The message Do you want to delete?(Deleted part will not be restored) is displayed.

7. Press buttons to select Yes, and then press the ENTER button. The selected section is deleted. To return to the Title List screen, press the buttons to select Return.

Edit Title List Screen Elements Playback bar Title List No. Section deletion starting point window and time Section deletion end point window and time Select the start and end points of the section you want to delete

using the playback related buttons. Playback related buttons ( , , , , , ).

The length of the section to be deleted must be at least 5 seconds long. If the length of the section to be deleted is less than 5 seconds, you will be prompted with the message "The range is too short." If the end time precedes the starting point, you will be prompted with the message "End point cannot be marked earlier than start point". The section cannot be deleted when it includes a still picture.

(VR mode)

Edit Title ListDVD-RW(VR)

Start DeleteEnd

Title List No. 05 Start End

00:00:05 00:00:20

00:00:20

Return

Do you want to delete? (Deleted part will not be restored.)

Yes No

MOVE ENTER RETURN EXIT

Edit Title ListDVD-RW(VR)

Title List No. 05

EndStart Return

00:00:05 00:10:15 00:10:15

Delete

Start End

MOVE ENTER RETURN EXIT

Edit Title ListDVD-RW(VR)

End

ReturnDeleteEndStart

Title List No. 05

00:00:05

00:00:05

00:00:00

MOVE ENTER RETURN EXIT

Start

00:06:35

Edit Title ListDVD-RW(VR)

ReturnDeleteEndStart

Title List No. 05

00:00:05

00:00:05

00:00:00

MOVE ENTER RETURN EXIT

Start End

01378A-AR650-XAA-ENG.indb 70 2007-03-13 11:56:27

Editing

English - 71

Advanced Editing (Playlist) Creating a Playlist

You can use this feature to create and extract new scenes from an existing recording. Follow these instructions to create a new playlist entry from a recorded title. 1. With the unit in Stop mode, press the MENU button on the remote control. 2. Press the buttons to select Playlist, and then press the ENTER or button.

3. Press the buttons to select New Playlist, and then press the ENTER or button. The Make Scene screen is displayed.

4. Press the ENTER button at the start point. The image and starting point time are displayed on the Start window. The yellow-colored selection bar moves to the End item. Select the starting point of the section from which you want to create

a new scene using the playback related buttons ( , , , , , , ).

5. Press the ENTER button at the end point. The image and end point time are displayed on the End window. The yellow-colored selection bar moves to the Make item.

- To make a new playlist - 6. Press the buttons to select Make, and then press the ENTER button.

A new Scene will be added to the current Playlist. A new Make Scene screen is displayed. Repeat the above steps 4~6 to create further scenes.

If you want to make a new playlist, go to MENU new playlist. You can check and see all the scenes on the Edit Playlist screen.

- To return to the Edit Playlist menu - 7. Press the buttons to select Return, and then press the ENTER button.

The Edit Playlist screen is displayed.

You can create up to 99 playlist entries. Depending on the disc type, the displayed screen may look slightly different. A disc that is recorded on this unit cannot be displayed playlist menu if EZ REC MODE set to 'On'.

Playing Entries in the Playlist

Follow these instructions to play the playlist entries. 1. With the unit in stop mode, press the PLAYLIST button.

The Edit Playlist screen is displayed. 2. Press the buttons to select the title you want to edit from the

Playlist, and then press the ENTER or button. 3. Press the buttons to select Play, and then select the ENTER button.

The playlist entries will be played. 4. Press the STOP( ) button to stop playing.

The screen returns to the Edit Playlist screen.

(VR mode)

(VR mode)

Make SceneDVD-Recorder DVD-RW(VR)

ReturnMakeEndStart

Scene No. 001

00:00:00

00:00:10

Title List : 1/6

Start

00:00:10

MOVE ENTER RETURN EXIT

End

Make SceneDVD-Recorder DVD-RW(VR)

Scene No. 001 Start

ReturnMakeEndStart

00:00:10 00:10:00

00:10:00

Title List : 1/6

II

MOVE ENTER RETURN EXIT

End

Edit PlaylistDVD-RW(VR) APR/23/2007

APR/23/2007 12:00 AM 1 Scene APR/23/2007 12:00 AM

01 APR/23/2007 12:00 00:00:21 02 APR/23/2007 12:30 00:00:03 03 APR/24/2007 12:00 00:00:15 04 APR/24/2007 12:30 00:00:16 05 APR/25/2007 12:00 00:06:32

No. Title Length Edit

1/5

MOVE ENTER RETURN EXIT

Edit PlaylistDVD-RW(VR) APR/24/2007

APR/24/2007 12:00 AM 1 Scene APR/24/2007 12:00 AM

01 APR/23/2007 12:00 00:00:21 02 APR/23/2007 12:3 00:00:03 03 APR/24/2007 12:0 00:00:15 04 APR/24/2007 12:3 00:00:16 05 APR/25/2007 12:0 00:06:32

No. Title Length Edit

Play Rename Edit Scene Copy Delete

3/5

MOVE ENTER RETURN EXIT

01378A-AR650-XAA-ENG.indb 71 2007-03-13 11:56:32

Ed iti

ng

English - 72

Renaming a Playlist Entry

Follow these instructions to rename a playlist entry, i.e. to edit the title of a playlist entry. 1. With the unit in stop mode, press the PLAY LIST button.

The Edit Playlist screen is displayed. 2. Press the buttons to select the title you want to edit from the

Playlist, and then press the ENTER or button. 3. Press the buttons to select Rename, and then press the ENTER

button. 4. Enter the desired characters using the buttons.

Back Space: Deletes the character before the cursor. Space: Enters a blank and moves the cursor one forward (to the right). Delete: Deletes the character at the cursor position. Clear: Deletes all the character inputs. Save: Registers the character inputs. The maximum number of characters that can be entered is 31. All 31

characters can be displayed by pressing the INFO button twice. 5. Press the buttons to select Save, and then press the ENTER

button. The changed title name is displayed on the title item of the selected playlist entry.

Editing a Scene for the Playlist

Follow these instructions to edit scenes for a playlist 1. With the unit in stop mode, press the PLAY LIST button.

The Edit Playlist screen is displayed. 2. Press the buttons to select the title you want to edit from the

Playlist, and then press the ENTER or button. 3. Press the buttons to select Edit Scene, and then press the

ENTER button. The Edit Scene screen is displayed.

Playing a Selected Scene 4. Press the buttons to select the scene you want to play, and

then press the ENTER button. The playlist entry to be played is selected.

5. Press the ENTER button. The selected scene is played. To stop scene play, press the STOP( ) button.

(VR mode)

(VR mode)

Back Space Space Delete Clear

RenameDVD-Recorder DVD-RW(VR)

Save

Dolphin

MOVE ENTER RETURN EXIT

Dolphin 1 Scene APR/24/2007 12:00 AM

01 APR/23/2007 12:00 00:00:21 02 APR/23/2007 12:30 00:00:03 03 Dolphin 00:00:15 04 APR/24/2007 12:30 00:00:16 05 APR/25/2007 12:00 00:00:32

Edit PlaylistDVD-RW(VR) Dolphin

No. Title Length Edit

MOVE ENTER RETURN EXIT

Edit SceneDVD-Recorder

Scene No. 1 / 7 Playlist No. 3 DVD-RW(VR)

01 00:00:26 02 00:00:07

04 00:00:03 Delete

Add

Move

Modify

Play

05 00:00:11

03 00:00:04

06 00:00:04

MOVE ENTER RETURN EXIT

Edit SceneDVD-Recorder

Scene No. 2 / 7 Playlist No. 3 DVD-RW(VR)

01 00:00:26 02 00:00:07

04 00:00:03 05 00:00:11

03 00:00:04

Play

Modify

Move

Add

Delete 06 00:00:04

MOVE ENTER RETURN EXIT

01378A-AR650-XAA-ENG.indb 72 2007-03-13 11:56:37

Editing

English - 73

Modifying a Scene (Replacing a Scene) Follow steps 1 to 3 of Editing a Scene for the Playlist on page 72. 4. Press the buttons to select the scene you want to modify,

and then press the ENTER button. 5. Press the buttons to select Modify, and then press the ENTER

button. 6. Press the ENTER button at the start point of the scene.

The image and starting point time are displayed on the Start window. Select the starting or ending point of the section you want to modify

using the playback related buttons ( , , , , , , ). 7. Press the ENTER button at the end point of the scene.

The image and ending point time are displayed on the End window. 8. Press the buttons to select Change, and then press the ENTER

button. The scene you want to modify is changed with the selected section.

Moving a Scene (Changing the Position of a Scene) Follow steps 1 to 3 of Editing a Scene for the Playlist on page 72. 4. Press the buttons to select the scene you want to move

(change the position), and then press the ENTER button. 5. Press the buttons to select Move, then press the ENTER button.

A yellow selection window is displayed on the scene to be moved. 6. Press the buttons to select the position to which you want to

move the selected scene, and then select the ENTER button. The selected scene is moved to the selected position.

Depending on the disc type, the displayed screen may look slightly different.

DVD-RW(VR)

Edit SceneDVD-Recorder

Scene No. 5/7 Playlist No. 3

01 00:00:26 02 00:00:04

04 00:00:11 05 00:00:04 06 00:00:04

03 00:00:03

Play

Modify

Move

Add

Delete

MOVE ENTER RETURN EXIT

Edit SceneDVD-Recorder

Scene No. 3/7 Playlist No. 3 DVD-RW(VR)

01 00:00:26 02 00:00:07

04 00:00:03 Delete

Add

Move

Modify

Play

05 00:00:11

03 00:00:04

06 00:00:04

MOVE ENTER RETURN EXIT

Edit SceneDVD-Recorder

Scene No. 2 / 7 Playlist No. 3 DVD-RW(VR)

01 00:00:26

04 00:00:03 05 00:00:11 06 00:00:04

03 00:00:0402 00:00:07

Play

Modify

Move

Add

Delete

MOVE ENTER RETURN EXIT

Modify SceneDVD-Recorder DVD-RW(VR)

Start Scene No. 002

CancelChangeEnd

II

Start

00:00:25 00:00:30

00:00:30

Title List : 5/6

MOVE ENTER RETURN EXIT

End

01 00:00:26 02 00:00:07

04 00:00:03 Delete

Add

Move

Modify

Play

05 00:00:11

03 00:00:04

Edit SceneDVD-Recorder

Scene No. 2 / 7 Playlist No. 3 DVD-RW(VR)

06 00:00:04

MOVE ENTER RETURN EXIT

Modify SceneDVD-Recorder DVD-RW(VR)

Scene No. 002

Start

00:00:25 00:00:00

00:00:25

Start End Change Cancel

Title List : 5/6

MOVE ENTER RETURN EXIT

End

01378A-AR650-XAA-ENG.indb 73 2007-03-13 11:56:42

Ed iti

ng

English - 74

Adding a Scene Follow steps 1 to 3 of Editing a Scene for the Playlist on page 72. 4. Press the buttons to select the scene that will have a new

scene inserted before it, and then press the ENTER button. A yellow selection window is displayed on the scene to be added as the new scene.

5. Press the buttons to select Add, then press the ENTER button. 6. Press the ENTER button at the starting point of the scene.

The image and starting point time are displayed on the Start window. Select the end point of the section where you want to add the new scene

using the playback related buttons ( , , , , , , ). 7. Press the ENTER button at the end point of the scene.

The image and end point time are displayed in the End window. To cancel, press the buttons to select Cancel and then press the

ENTER button. 8. Press the buttons to select Add, and then press the ENTER

button. The section you want to add is inserted prior to the scene selected in

step 4.

Deleting a Scene Follow steps 1 to 3 of Editing a Scene for the Playlist on page 72. 4. Press the buttons to select the scene you want to delete, and

then press the ENTER button. 5. Press the buttons to select Delete, and then press the ENTER

button.

Edit SceneDVD-Recorder

Scene No. 4/7 Playlist No. 3 DVD-RW(VR)

01 00:00:26 02 00:00:07

04 00:00:03 Delete

Add

Move

Modify

Play

05 00:00:11

03 00:00:04

06 00:00:04

MOVE ENTER RETURN EXIT

Add SceneDVD-Recorder DVD-RW(VR)

Scene No. 004 Start

CancelAddEndStart

Title List : 4/6 00:00:15 00:00:00

00:00:15

MOVE ENTER RETURN EXIT

End

00:00:35

Add SceneDVD-Recorder DVD-RW(VR)

Start

CancelAddEndStart

Scene No. 004

00:00:15 00:00:35Title List : 4/6

II

MOVE ENTER RETURN EXIT

End

DVD-RW(VR)

Edit SceneDVD-Recorder

Scene No. 4/8 Playlist No. 3

01 00:00:26 02 00:00:07

04 00:00:20 05 00:00:03 06 00:00:11

03 00:00:04

Play

Modify

Move

Add

Delete

MOVE ENTER RETURN EXIT

DVD-RW(VR) Edit SceneDVD-Recorder

Scene No. 2/7 Playlist No. 3

01 00:00:26 02 00:00:07

04 00:00:03 05 00:00:11 06 00:00:04

03 00:00:04

Play

Modify

Move

Add

Delete

MOVE ENTER RETURN EXIT

DVD-RW(VR) Edit SceneDVD-Recorder

Scene No. 2/6 Playlist No. 3

01 00:00:26 03 00:00:04

05 00:00:11 06 00:00:04 06 00:00:05

04 00:00:03

Play

Modify

Move

Add

Delete

MOVE ENTER RETURN EXIT

01378A-AR650-XAA-ENG.indb 74 2007-03-13 11:56:49

Editing

English - 75

Copying a Playlist Entry to the Playlist 1. Press the PLAY LIST button.

The Edit Playlist screen is displayed. 2. Press the buttons to select the title you want to copy to the

Playlist, and then press the ENTER or button. 3. Press the buttons to select Copy, and then press the ENTER

button. Playlist that has been selected will be copied.

The playlist can contain up to 99 playlist entries (titles).

Deleting a Playlist Entry from the Playlist 1. With the unit in Stop mode, press the PLAY LIST button.

The Edit Playlist screen is displayed. 2. Press the buttons to select the title you want to edit from the

Playlist, and then press the ENTER or button. 3. Press the buttons to select Delete, and then press the ENTER button. 4. Press the buttons to select Yes, and then press the ENTER button.

You are automatically returned to the Edit Playlist screen after the deletion operation has nished.

Disc Manager Editing the Disc Name

Follow these instructions to give a name to a disc. 1. With the unit in Stop mode, press the MENU button on the remote control. 2. Press the buttons to select Disc Manager, then press the ENTER

or button. 3. Press the buttons to select Disc Name, then press the ENTER or button. The Rename screen is displayed.

4. Enter the desired characters using the buttons. Back Space : Deletes the character before the cursor. Space : Enters a blank and moves the cursor one forward (to the right). Delete : Deletes the character at the cursor position. Clear : Deletes all the character inputs. Save : Registers the character inputs. The maximum number of characters that can be entered is 31. All 31

characters can be displayed by pressing the INFO button twice. 5. Press the buttons to select Save, and then press the ENTER button.

A disc name is given to the disc.

You may need to disable disc protection before beginning editing. (see page 76.) Depending on the kind of disc, the displayed screen may be different.

RenameDVD-Recorder DVD-RW(VR)

Back Space Space Delete Clear

Save

D i s c

MOVE ENTER RETURN EXIT

Edit PlaylistDVD-RW(VR) Dolphin

Dolphin 7 Scene APR/23/2007 06:43 AM

Yes No

Do you want to delete?

5/5

MOVE ENTER RETURN EXIT

Edit PlaylistDVD-RW(VR) Dolphin

Dolphin 7 Scene APR/23/2007 06:43 AM

01 Science 00:00:17

02 Sky 00:00:06

03 Dolphin 00:00:06

04 Natural 00:00:37

05 Dolphin 00:00:06

No. Title Length Edit

5/5

MOVE ENTER RETURN EXIT

3/4

Edit PlaylistDVD-RW(VR) Dolphin

Dolphin 7 Scene APR/23/2007 06:43 AM

01 Science 00:00:17

02 Sky 00:00:06 03 Dolphin 00:00:06 04 Natural 00:00:37

Play Rename Edit Scene Copy Delete

No. Title Length Edit

/

MOVE ENTER RETURN EXIT

Disc ManagerDVD-Recorder DVD-RW(VR)

Title List

Playlist

Disc Manager

Timer Rec.

Setup

Disc Name :

Disc Protection : Not Protected

Disc Format : DVD-VR

Disc Finalize

Delete All Title Lists

MOVE ENTER RETURN EXIT

01378A-AR650-XAA-ENG.indb 75 2007-03-13 11:56:57

Ed iti

ng

English - 76

Disc Protection

Disc Protection allows you to protect your discs from being formatted or deleted due to unintended operations 1. With the unit in Stop mode, press the MENU button on the remote control. 2. Press the buttons to select Disc Manager, and then press the

ENTER or button. 3. Press the buttons to select Disc Protection, then press the

ENTER or button. 4. Press the buttons to select Protected, then press the ENTER button.

Formatting a Disc

DVD-RAM/DVD-RW discs must be prepared (formatted) before they can be recorded on. Use these instructions to format a disc. Disable disc protection before formatting.

1. With the unit in Stop mode, press the MENU button on the remote control. 2. Press the buttons to select Disc Manager, and then press the

ENTER or button. 3. Press the buttons to select Disc Format, and then press the

ENTER or button.

DVD-RAM You will be prompted with the con rmation message Do you want to

format disc?. If you select Yes using the buttons and press the ENTER button,

you will be prompted with the con rmation message All data will be deleted. Do you want to continue?.

DVD-RW You will be prompted with the con rmation message Choose the

recording format for DVD-RW 4. Press the buttons to select desired mode, then press the ENTER

button. You will be prompted again with the message All data will be deleted.

Do you want to continue? 5. Press the buttons to select Yes, and then press the ENTER

button. The disc is formatted.

DVD-VR and DVD-V modes are compatible with the following disc types.

DISC

DVD-VR DVD-V

DVD-RAM DVD-RW

DVD-RW DVD-R

Menu items may differ depending on the disc type. Discs need to be formatted in the following cases: - The rst time you use a new DVD-RAM/-RW Disc - You want to change the VR or V mode of a DVD-RW disc.

Disc ManagerDVD-Recorder DVD-RW(VR)

Title List

Playlist

Disc Manager

Timer Rec.

Setup

Disc Name :

Disc Protection : Protected

Disc Format : DVD-VR

Disc Finalize

Delete All Title Lists

MOVE ENTER RETURN EXIT

DVD-RAM

DVD-RW

Disc ManagerDVD-Recorder DVD-RAM(VR)

Title List

Playlist

Disc Manager

Timer Rec.

Setup

Disc Name :

Disc Protection : Protected

Disc Format : DVD-VR

Disc Finalize

MOVE ENTER RETURN EXIT

Do you want to format disc?

Yes No

Disc ManagerDVD-Recorder DVD-RW(VR)

Title List

Playlist

Disc Manager

Timer Rec.

Setup

Disc Name :

Disc Protection : Not Protected

Disc Format : DVD-VR

Disc Finalize

Delete All Title Lists

MOVE ENTER RETURN EXIT

Choose the recording format for DVD-RW

DVD-VR DVD-V

Disc ManagerDVD-Recorder DVD-RW(VR)

Title List

Playlist

Disc Manager

Timer Rec.

Setup

Disc Name :

Disc Protection : Not Protected

Disc Format : DVD-VR

Disc Finalize

Delete All Title Lists

MOVE ENTER RETURN EXIT

All data will be deleted. Do you want to continue?

Yes No

01378A-AR650-XAA-ENG.indb 76 2007-03-13 11:57:00

Editing

English - 77

Finalizing a Disc

After you record titles onto a DVD-RW/DVD-R disc with your DVD recorder, it needs to be nalized before it can be played back on external devices such as a DVD player. 1. With the unit in Stop mode, press the MENU button on the remote control. 2. Press the buttons to select Disc Manager, and then press the

ENTER or button. 3. Press the buttons to select Disc Finalize, and then press the

ENTER or button. You will be prompted with the message Do you want to nalize disc?.

4. Press the buttons to select Yes, then press the ENTER button. You will be prompted again with the message Disc will be nalized. Do you want to continue?.

5. Press the buttons to select Yes, and then press the ENTER button. The disc is nalized.

Once a disc is nalized, you cannot delete entries from the record list. Once a DVD-R/DVD-RW (video mode)disc is nalized, it is playable in a standard DVD player. Depending on disc type, the displayed screen may appear slightly different. Finalizing time may be different depending on the amount of data recorded on the disc. Data on the disc will be damaged if the recorder is powered off during nalizing process. You can nalize automatically using EZ REC MODE. (See page 54)

Un nalizing a Disc (V/VR mode)

1. With the unit in Stop mode, press the MENU button on the remote control. 2. Press the buttons to select Disc Manager, and then press the

ENTER or button. 3. Press the button to select Disc Un nalize, and then press the

ENTER or button. You will be prompted with the message Do you want to un nalize disc?.

4. Press the buttons to select Yes, then press the ENTER button. You will be prompted again with the message Disc will be un nalized. Do you want to continue?.

5. Press the buttons to select Yes, and then press the ENTER button.The disc is un nalized.

A DVD-RW can be nalized or un nalized in Video mode.

Finalize Un nalize Mark DVD-Video(RW) DVD-RW(V)

Operation Same as DVD-Video Additional recording, protection and deletion are possible.

A DVD-RW can be nalized or un nalized in VR mode.

Finalize Un nalize Mark DVD-RW(VR:F) DVD-RW(VR)

Operation

Additional recording, deletion, editing, and

protection are impossible.

Additional recording, deletion, editing, and

protection are possible.

Disc ManagerDVD-Recorder DVD-RW(VR:F)

Title List

Playlist

Disc Manager

Timer Rec.

Setup

Disc Name :

Disc Format : DVD-VR

Disc Unfinalize

MOVE ENTER RETURN EXIT

01378A-AR650-XAA-ENG.indb 77 2007-03-13 11:57:03

Ed iti

ng

English - 78

Delete All Title Lists

The disc protection should be disabled rst. 1. With the unit in Stop mode, press the MENU button on the remote

control. 2. Press the buttons to select Disc Manager, and then press the

ENTER or button. 3. Press the buttons to select Delete All Title Lists, and then press

the ENTER or button. When Protected Entry exists: The Delete All Title List function will not

operate. If you want to delete a protected title, disable Protection for it on the Lock item. (See page 69)

4. Press the buttons to select Yes, and then press the ENTER button. All title lists are deleted.

Disc ManagerDVD-Recorder

DVD-RW(VR)

Title List

Playlist

Disc Manager

Timer Rec.

Setup

Disc Name :

Disc Protection : Not Protected

Disc Format : DVD-VR

Disc Finalize

MOVE ENTER RETURN EXIT

Do you want to delete all title lists?

Yes No

01378A-AR650-XAA-ENG.indb 78 2007-03-13 11:57:06

Additional Inform ation

English - 79

Additional Information

Troubleshooting If your product malfunctions, go through the checkpoints below before contacting a Samsung authorized service center.

Power The input is displayed for a while when the power is turned on.

The DVD recorder requires some time to initialize and the input will be displayed for approx. 10 seconds after it is turned on.

Recording Cannot record TV programs.

Check whether the power cord is securely plugged into the power outlet.

Check the free space on your DVD-RAM/DVD-RW/DVD-R discs.

I pressed the REC button but there is no response.

Recording is possible for DVD-RAM/DVD-RW/DVD-R discs only. If a program is copy protected, it cannot be recorded.

Playback Cannot play the disc.

Check whether the disc is inserted correctly with the label facing up.

Check the regional code of the DVD disc.

This DVD recorder cannot play some types of discs. (See pages 5, 56)

icon appears on the screen.

You cannot use this operation or function due to one of the following reasons: (1) Your DVD disc restricts it. (2) Your DVD disc does not support this

feature (for example: angles) (3) The feature is not available at the

moment. (4) You've requested a title, chapter, or

scan time that is out of range.

Play mode settings are different from the settings con gured in the Settings menu.

The disc does not support all selected functions. In this case, some settings con gured in the settings menu may not work properly.

Cannot change the aspect ratio.

The aspect ratio is xed for DVD discs. (See page 39)

The angle operation does not work while playing a DVD disc.

The angle operation is available only when the disc contains images captured from different angles.

The selected audio and/or subtitle language is not played.

Audio and subtitle languages are disc speci c. Only the sound and subtitle languages contained on the DVD disc are available and displayed in the disc menu.

Video The disc revolves, but no image or bad quality images are displayed.

Check whether there is damage to or any foreign material on your disc.

Some low quality discs may not play properly.

If scenes change from dark to bright suddenly, the screen may shake vertically temporarily, but this is not a default of the unit.

Checkpoint 1

Checkpoint 1

Checkpoint 2

Checkpoint 1

Checkpoint 1

Checkpoint 2

Checkpoint 3

Checkpoint 1

Checkpoint 1

Checkpoint 1

Checkpoint 1

Checkpoint 1

Checkpoint 1

Checkpoint 2

Checkpoint 3

01378A-AR650-XAA-ENG.indb 79 2007-03-13 11:57:07

Ad di

tio na

l In fo

rm at

io n

English - 80

Sound No sound.

Are you watching a program in scan mode? If you are playing a program at a speed other than normal and fast1 speed, the sound will not be heard.

Check the connections and settings.

Check whether the disc is damaged. Clean the disc, if necessary.

Check whether the disc is inserted correctly with the label facing up.

No audio output.

Check whether you have selected the correct digital output options in the Audio Output Options menu. (See page 38)

Timer Recording Timer lamp ickers.

Check if there is enough space in the disc for recording.

Check whether the current disc is recordable or not. Make sure to check before the start time of recording.

Timer recording does not work properly.

Re-check the recording time and the end time settings again.

Recording will be cancelled, if the power is disconnected due to a power failure or other similar reason, while recording.

HDMI No HDMI output.

Check to see that the Video output is HDMI enabled.

Check the connection between the TV and the HDMI jack of the DVD Recorder.

See if your TV supports 480p/720p/1080i resolution.

Abnormal HDMI output screen.

If snow noise appears on the screen, it means that the TV does not support HDCP (High-bandwidth Digital Content Protection). If connected via DVI, try turning the DVD Recorder off then On.

HDMI output Jitter

Check your TV system setup correctly.

Screen Jitter may occur when the frame rate is converted from 50Hz to 60Hz for 720p/1080i HDMI (High De nition Multimedia Interface) Output.

Please refer to the user's manual of your TV.

Remote Control Unit The remote control doesn't work.

Point the remote control at the remote control sensor on your DVD recorder. Allow for proper distance. Remove obstacles between your DVD recorder and the remote control.

Check whether the batteries are empty.

Other I forgot my password for parental supervision.

Remove the disc. Press the CH ( / ) buttons on the front panel of the DVD Recorder simultaneously for 5 seconds or more when the power is on. All settings including the password will revert to the factory settings. Do not use this unless absolutely necessary. (Note that this function is possible only when no disc is inserted.)

Is it possible to change a subtitle and an audio signal on a recorded disc?

A recorded disc is played with only the subtitle and the audio signal which were selected during recording.

Other problems. Read the table of contents and then nd and read the section describing your problem, and follow the instructions given.

Turn your DVD recorder off and on.

If the problem still persists, contact a nearby Samsung service center.

Checkpoint 1

Checkpoint 2

Checkpoint 3

Checkpoint 4

Checkpoint 1

Checkpoint 1

Checkpoint 2

Checkpoint 1

Checkpoint 2

Checkpoint 3

Checkpoint 1

Checkpoint 2

Checkpoint 3

Checkpoint 1

Checkpoint 1

Checkpoint 2

Checkpoint 1

Checkpoint 1

Checkpoint 2

Checkpoint 3

Checkpoint 1

Checkpoint 2

Checkpoint 1

01378A-AR650-XAA-ENG.indb 80 2007-03-13 11:57:09

Additional Inform ation

English - 81

Cable Box/Satellite Receiver Brand Code Table

Cable box brand

Cable box brand Code number 3M 0033 ABC 0003, 0011, 0017, 0008, 0014, Accuphase 0007, 0001, 0013, 0206, 0047,

0237, 0033 0003, 0013, 0047, 0001, 0011,

Acorn 0017, 0014, 0206, 0007 1102, 0237

Action 0237 Active 0237, 1102 Aim 0015 Allegro 0315, 0153 Amark 0008, 0277, 0144, 0056 American 0060 Americast 0899 Antronix 0207, 0022 Anvision 0211, 0111 Apache 0770 Arbatron 0014, 0011, 0003, 0476 Archer 0153, 0022, 0207, 0039, 0797, ASE 0237, 0260

1080 Auna 1269 BBT 0267 BCC 0276 Belcor 0056, 0022 Bell & Howell 0014 Bell Atlantic 0641 Bell South 0899 Bestlink 0303 Betavue 0022 British Telecom 0003 BVS 0641 Cable Healthcare 0769, 0058 Cable Star 0056 Cabletenna 0022, 0039 Cableview 0022 Century 0153, 0618, 0008, 0315 Citation 0017 Citizen 0153, 0315, 0078, 0242 Clearmaster 0883 ClearMax 0883, 1247 Colour Voice 0031, 0025 Comband 0233, 0232 Comtec 0274 Comtronics 0060, 0040 Comtronics Eagle 0040, 0060 Contec 0019 Coolmax 0883 Curtis Mathes 0015, 0242 Dae Ryung Eagle 0008 Dae Ryung 0008, 0877, 0477, 0277, 1877 Diamond 0035 Digeo 1476,1897 Digi 0637 Director 0476 Dumont 0637 Eagle Comtronics 0060, 0028

Cable box brand Code number Eastern 0002, 0274, 0418 Electricord 0078 Emerson 0797, 0303, 0015, 0014 Everquest 0040, 0015 Focus 0400 Fosgate 0276 Fujitsu 0246 Funai 0248, 0019 FutureVision 0649 Garrard 0153 Gateway 0764 GC Electronics 0207, 0056, 0330, 0016, 0040,

0077, 0030 GE 0232, 0233, 0144, 0021 Gemini 0015, 0070, 0057, 0242, 0014,

0797, 0013, 0400 General Instrument 0476,0011,0014,0098,0810,

0024,0003,0015,0276,1376,1476 GHZ 0078 Gibraltar 0003 Global 1327 GMI 0069, 0057, 0015, 0797 Goldstar 0144, 0040 Goodmind 0770, 0797 Gradiente 1136 Hamlin 0020, 0009, 0034, 0259, 0015,

0273, 0206 Healthway Interactive 0058, 1020, 1015, 0769 Hitachi 0011, 0154, 0009, 0008, 0003,

0033, 0014, 0255 Houston Tracker 0011 Hwalin 0303 Hytex 0007 IBM 0670 IEEC 1018 Interbuy 0274 Jasco 0315, 0153, 0015 Jebsee 0014, 0400 Jerrold 0003, 0014, 0276, 0011, 0012,

0020, 0024, 0015, 0047, 0098, 0476, 0031, 0029, 0111, 0032, 0054, 0810, 0028

Kuang Yu 0024 Leon 0069, 0015 LG 0040, 0144 Linsay 0440 Macom 0033 Maestro 0812 Magnavox 0797, 0027, 0032, 0334, 0069 Millennium 0618, 0153 Memorex 0000 Mitsubishi 0003 Motorola 0476, 0276, 1476, 0810, 1376,

1254, 0400, 1106 Movie Time 0156, 0078, 0063, 0203 MS 0069, 0015, 1018, 0303 MultiVision 0012 Myrio 1117 NET 0274 Next Level 0764, 1316, 1315, 1314

01378A-AR650-XAA-ENG.indb 81 2007-03-13 11:57:11

Ad di

tio na

l In fo

rm at

io n

English - 82

Cable box brand Code number Nexus 0770 Northcoast 0671, 0314 Nova Vision 0277, 0008 Novabeam 0277 Novaplex 0618, 0277, 0017, 0008 NSC 0156, 0070, 0203, 0063, 0400,

0012, 0618, 0022, 0637, 0010, 0044

Oak 0019, 0007, 0303, 0248, 0017 Omega 0015 Omniview 0371 Optimus 0021 Pace 0008,0237,0277,0477,0877,

1877,0810,1376,1476 Paci c Bell 0843 Panasonic 0107, 0021, 0144, 0008, 0124,

0307, 0000, 0040 Panther 0637 Paragon 0000, 0525, 0008 Penney 0637, 0000 Philips 0025, 0031, 0290, 0027, 0030,

0153, 0060, 0242, 0028, 0334, 0211, 0029, 0259,0307, 0652, 0013, 0069, 0649, 0255, 0305, 0032, 0111, 0317

Pioneer 0144, 0023, 0533, 1877, 0877, 0260, 0008, 0277, 0477

Popular Mechanics 0400 Prelude 0770 Prism 0012, 0013, 0059 Protelcon 0786 Pulsar 0000, 0040 Quasar 0000 Quest 0144, 0020 R Line 0040 RadioShack 0883, 0015, 0315, 0303, 0797 Rampage 0255 Ranger 1247 RCA 0021, 0060, 0797,0047, 1256,

0843 Realistic 0207, 0153 Recoton 0153, 0400 Regal 0259, 0020, 0273, 0279, 0276 Regency 0002, 0020, 0682 Rembrandt 0070, 0153, 0040, 0022, 0011 RK 0304, 0479 Runco 0000 Samsung 0040, 0144, 0023, 0003, 0070,

0000, 1898 Sasktel 1737 Scienti c Atlanta 0008, 0277, 0017, 0006, 0237,

0025, 0477, 0207, 0877, 0003, 0012, 0000, 0021, 1877

Seam 0510 Sears 0510 Sejin 1265 Siemens 0246 Sigma 0019 Signal 0040, 0015, 0011, 0035 Signature 0011 SkyCable 0112 Skygiant 1091 SL Marx 0040 Sony 1006, 1506, 1606 Spectradyne 0769, 0058 Spectravision 0058 Sprucer 0021, 0307, 0010, 0144

Cable box brand Code number Standard Components 0203, 0096, 0155

Starcom0003, 0015, 0047, 0014, 0098, 0305

Stargate 0015, 0040, 0770, 0865, 0797, 0305, 0014

Starquest 0015 StarSight 0542, 0422 Stealth 0274 Stellar One 0807 Storm 1018, 0637 Suena Madritel 1230 Supercable 0276 Supermax 0883 Sylvania 0001 Tandy 0258 Tatung 0097 Teac 1018 Technics 0029 Teknika 0146 Teleavia 0040 TeleCaption 0221 Teleview 0063, 0040 Texscan 0001, 0096, 0010 TFC 0310 Thomson 1256 Timeless 0418, 0274, 0040 Tocom 0012, 0013, 0029, 0019, 0059,

0017 Torx 0003 Toshiba 0000 Trans PX 0303, 0276, 0153, 0315 Trinity 1248 Tristar 0883 TS 0255, 0024, 1018, 0003, 0303 Tusa Tusa TV COMM 0035, 0019 TV Guide 1476 TV86 0063, 0040 Uniden 0225, 0022 Unika 0207, 0153, 0022 United Artists 0007 United Cable 0003, 0014, 0011, 0276 Universal 0191, 0078, 0207, 0056, 0022,

0039, 0153, 0077, 0322, 0315 US Electronics 0276, 0008, 0003, 0017 V2 0883 Verizon 0246 Video way 0250, 0000 Video Works 0124 Vidtech 0244 Viewmaster 0883, 0770 Viewstar 0258, 0289, 0060, 0063, 0211,

0618, 01530027, 0111, 0030, 0121 Vision 0883 Visionetics 1264 Vortex View 0883 WaveMaster 0565 Wiso 0078 Zenith 0000, 0525, 0054, 0017, 0039,

0153, 0060, 0315, 0191, 0899 Zenitek 0400

01378A-AR650-XAA-ENG.indb 82 2007-03-13 11:57:12

Additional Inform ation

English - 83

Satellite receiver brand

Satellite receiver brand Code number AlphaStar 0772 Atlantic Telephone 1333 Bell ExpressVu 0775 Century 0856 Chaparral 0216 Crossdigital 1109 DirecTV 1887, 0749, 0566, 0392, 1749,

0099, 1109, 1076, 1442, 1856, 0247, 1142, 1639, 0724, 0639,

Dish Network System 0775, 1005, 1170 Dishpro 0775, 1005 Echostar 0775, 1170, 1005 Expressvu 0775 Galaxis 0863 GE 0566 General Instrument 0361, 0869, 0627 GOI 0775 Gradiente 0856 Hitachi 0819, 0749 Houston Tracker 0775 HTS 0775 Hughes Network Systems 0749, 1749, 1442, 1142 Humax 1176, 1359, 1048, 0863, 0283 Innova 0099 Jerrold 0361, 0036, 0627 JVC 0775, 1170 Magnavox 0722, 0724 McIntosh 0869 Memorex 0724 Mitsubishi 0749 Motorola 0869 NEC 1270, 0496, 0499, 0507, 0508 Netsat 0099 Next Level 0869 Optimus 0724 Panasonic 0247, 0701 Paysat 0724 Philips 1076, 1142, 0724, 0722, 0749,

1442, 1749, 0856, 0775, 0099 Primestar 0361, 0627, 0869 Proscan 0392, 0566 QNS 1367 RadioShack 0869 RadioShack 0566, 0392, 0143, 0855 Samsung 1109, 1276 Sky 0856, 0099, 1856 Sony 0639, 1639 Star Choice 0869 Star Trak 0869, 0772 Thomson 0566, 0392 Tivo 1142, 1442 Toshiba 0790, 0749, 1749, 1285 UEC 1333, 1358 Uniden 0724, 0722 Video Cipher II Plus 0361 Zenith 0856, 1856

01378A-AR650-XAA-ENG.indb 83 2007-03-13 11:57:13

Ad di

tio na

l In fo

rm at

io n

English - 84

Error Message Solutions Before contacting a Samsung authorized service center, perform the following simple checks.

Error Message Solution / Explanation

You cannot record a copy protected movie. You cant record the video since it is protected by copyright.

You cannot record. This disc is protected.

The disc you are using is protected. To record on this disc or use this function, disable the disc protection function. Refer to page 76.

This disc cannot be formatted (the disc is protected).

This disc cannot be renamed (the disc is protected).

The disc cannot be nalized (the disc is protected).

This [Menu] is not available (the disc is protected).

The disc cannot be played, Please check the regional code of the disc.

The disc does not match the regional code for your area and cannot be played on this device.

This disc cannot be formatted. Please check the disc.

Make sure there are no scratches or dirt on the disc.

You could not format the disc because of error detection.

You could not nalize the disc because of error detection.

You could not un nalize the disc because of error detection.

The disc cannot be played, Please check the TV system. PAL format discs cannot be played on this unit.

The disc can be neither played nor recorded.

Make sure there are no scratches or dirt on the disc. The disc cannot be played, Please check the disc.

If the disc has invalid information, no more titles can be recorded. Please format the disc beforehand.

You cant use the disc because it contains errors from previous recordings. Use the disc after formatting.

01378A-AR650-XAA-ENG.indb 84 2007-03-13 11:57:14

Additional Inform ation

English - 85

Error Message Solutions

Error Message Solution / Explanation

Error is detected on the disc. You cant use the disc because it contains errors from previous recordings. Use the disc after formatting.

System error is found. Please try it again after turning off the power.

When operating, errors happen. Turn off the device. (To turn off, press and hold the power button on the front of the device for 10 seconds.) After turning off, press the Open button and remove the disc from the device.

The DV device is not connected. Make sure the DV device is connected properly to the DV connection Jack. If it is connected properly, turn it off and on once again.

If you are unable to solve the problem after reading the above instructions, note:

The model and serial number on the rear of your DVD Recorder

The warranty information

A clear description of the problem

Then contact your nearest SAMSUNG authorized service center. Call 1-800-SAMSUNG for a center near you.

01378A-AR650-XAA-ENG.indb 85 2007-03-13 11:57:15

Ad di

tio na

l In fo

rm at

io n

English - 86

Speci cations

General

Power requirements 120V AC, 60Hz

Power consumption 28 Watts

Weight 7.12lb

Dimensions 16.9 in(W) x 12in(D) x 2.3in(H)

Operating temp. +41F to +95F

Other conditions Keep level when operating. Less than 75% operating humidity

Input

Broadcasting standard NTSC, ATSC

Band coverage Air 2 ~ 69, Cable 1 ~ 135

Video (1,2) 1.0 V p-p at 75 load, sync negative

S-Video input (Y: 1.0Vp-p, C: 0.286Vp-p at 75 load)

Audio(1,2) Max.Audio Input Level : 2Vrms

DV Input IEEE 1394(4p) compatible jack

Output

Audio

Analog output jacks 1, 2

Optical/Coaxial digital audio output

Full scale Analog output level : 2Vrms

Video

Video output jack

S-Video output (Y:1.0Vp-p, C:0.286Vp-p at 75 load)

Component output (Y: 1.0Vp-p, Pb: 0.70Vp-p, Pr: 0.70Vp-p at 75 load)

HDMI output (480p, 720p, 1080i)

Recording

Picture Compression format MPEG-II

Audio Compression format Dolby Digital 2ch/256kbps

Recording Quality XP (about 8 Mbps), SP (about 4 Mbps), LP (about 2 Mbps), EP (about 1.2 Mbps or about 0.8 Mbps)

Audio Frequency Response 20 Hz ~ 20 kHz

Audio Output Disc Type DVD AUDIO CD(CDDA)

Analog Audio Output 48 / 96kHz 44.1kHz Digital Audio Output 48kHz 44.1kHz

For DVD discs, audio signals recorded at 96kHz sampling frequency are converted and output at 48kHz.

01378A-AR650-XAA-ENG.indb 86 2007-03-13 11:57:16

Warranty

LIMITED WARRANTY TO ORIGINAL PURCHASER

This SAMSUNG brand product, as supplied and distributed by Samsung Electronics America, Inc. (SAMSUNG) and delivered new, in the original carton to the original consumer purchaser, is warranted by SAMSUNG against manufac- turing defects in materials and workmanship for a limited warranty period of:

One (1) Year Parts / Ninety (90) days Labor (90 days Parts and Labor for Commercial Use)

This limited warranty begins on the original date of purchase, and is valid only on products purchased and used in the United States. To receive warranty service, the purchaser must contact SAMSUNG for problem determination and service procedures. Warranty service can only be performed by a SAMSUNG authorized service center. The original dated bill of sale must be presented upon request as proof of purchase to SAMSUNG or SAMSUNGs authorized ser- vice center. Transportation of the product to and from the service center is the responsibility of the purchaser. SAMSUNG will repair or replace this product, at our option and at no charge as stipulated herein, with new or recon- ditioned parts or products if found to be defective during the limited warranty period specified above. All replaced parts and products become the property of SAMSUNG and must be returned to SAMSUNG. Replacement parts and prod- ucts assume the remaining original warranty, or ninety (90) days, whichever is longer. SAMSUNG s obligations with respect to software products distributed by SAMSUNG under the SAMSUNG brand name are set forth in the applicable end user license agreement. Non-SAMSUNG hardware and software products, if provided, are on an AS IS basis. Non-SAMSUNG manufacturers, suppliers, publishers, and service providers may provide their own warranties. This limited warranty covers manufacturing defects in materials and workmanship encountered in normal, and except to the extent otherwise expressly provided for in this statement, noncommercial use of this product, and shall not apply to the following, including, but not limited to: damage which occurs in shipment; delivery and installation; applications and uses for which this product was not intended; altered product or serial numbers; cosmetic damage or exterior fin- ish; accidents, abuse, neglect, fire, water, lightning or other acts of nature; use of products, equipment, systems, utilities, services, parts, supplies, accessories, applications, installations, repairs, external wiring or connectors not supplied and authorized by SAMSUNG, or which damage this product or result in service problems; incorrect electrical line voltage, fluctuations and surges; customer adjustments and failure to follow operating instructions, cleaning, maintenance and environmental instructions that are covered and prescribed in the instruction book; product removal or reinstallation; reception problems and distortion related to noise, echo, interference or other signal transmission and delivery prob- lems. SAMSUNG does not warrant uninterrupted or error-free operation of the product. THERE ARE NO EXPRESS WARRANTIES OTHER THAN THOSE LISTED AND DESCRIBED ABOVE, AND NO WARRANTIES WHETHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, SHALL APPLY AFTER THE EXPRESS WARRANTY PERIODS STATED ABOVE, AND NO OTHER EXPRESS WARRANTY OR GUARANTY GIVEN BY ANY PERSON, FIRM OR CORPORATION WITH RESPECT TO THIS PRODUCT SHALL BE BINDING ON SAMSUNG. SAMSUNG SHALL NOT BE LIABLE FOR LOSS OF REVENUE OR PROFITS, FAILURE TO REALIZE SAVINGS OR OTHER BENEFITS, OR ANY OTHER SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES CAUSED BY THE USE, MISUSE OR INABILITY TO USE THIS PRODUCT, REGARDLESS OF THE LEGAL THEORY ON WHICH THE CLAIM IS BASED, AND EVEN IF SAMSUNG HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. NOR SHALL RECOVERY OF ANY KIND AGAINST SAMSUNG BE GREATER IN AMOUNT THAN THE PURCHASE PRICE OF THE PRODUCT SOLD BY SAMSUNG AND CAUSING THE ALLEGED DAMAGE. WITHOUT LIMITING THE FOREGOING, PURCHASER ASSUMES ALL RISK AND LIABILITY FOR LOSS, DAMAGE OR INJURY TO PURCHASER AND PURCHASERS PROPERTY AND TO OTHERS AND THEIR PROPERTY ARISING OUT OF THE USE, MISUSE OR INABILITY TO USE THIS PRODUCT SOLD BY SAMSUNG NOT CAUSED DIRECTLY BY THE NEGLIGENCE OF SAMSUNG. THIS LIMITED WARRANTY SHALL NOT EXTEND TO ANYONE OTHER THAN THE ORIGINAL PURCHASER OF THIS PRODUCT, IS NONTRANSFERABLE AND STATES YOUR EXCLUSIVE REMEDY. Some states do not allow limitations on how long an implied warranty lasts, or the exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. To obtain warranty hardware service, please contact SAMSUNG at:

Samsung Electronics America, Inc. 105 Challenger Road Ridgefield Park, NJ 07660-0511

1-800-SAMSUNG (726-7864) and www.samsung.com

01378A-AR650-XAA-ENG.indb 87 2007-03-13 11:57:17

Contact SAMSUNG WORLD WIDE If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care center.

Region Country Customer Care Center Web Site

North America CANADA 1-800-SAMSUNG (7267864) www.samsung.com/ca MEXICO 01-800-SAMSUNG (7267864) www.samsung.com/mx U.S.A 1-800-SAMSUNG (7267864) www.samsung.com

Latin America

ARGENTINE 0800-333-3733 www.samsung.com/ar BRAZIL 0800-124-421

4004-0000 www.samsung.com/br CHILE 800-726-7864 (SAMSUNG) www.samsung.com/cl COSTA RICA 0-800-507-7267 www.samsung.com/latin ECUADOR 1-800-10-7267 www.samsung.com/latin EL SALVADOR 800-6225 www.samsung.com/latin GUATEMALA 1-800-299-0013 www.samsung.com/latin JAMAICA 1-800-234-7267 www.samsung.com/latin PANAMA 800-7267 www.samsung.com/latin PUERTO RICO 1-800-682-3180 www.samsung.com/latin REP. DOMINICA 1-800-751-2676 www.samsung.com/latin TRINIDAD & TOBAGO 1-800-7267-864 www.samsung.com/latin VENEZUELA 0-800-100-5303 www.samsung.com/latin COLOMBIA 01-8000112112 www.samsung.com.co

Europe

BELGIUM 02 201 2418 www.samsung.com/be

CZECH REPUBLIC 844 000 844 Distributor pro eskou republiku : Samsung Zrt., eska organizan sloka Vyskoilova 4, 14000 Praha 4

www.samsung.com/cz

DENMARK 70 70 19 70 www.samsung.com/dk FINLAND 030-6227 515 www.samsung.com/ FRANCE 3260 SAMSUNG or

08 25 08 65 65 ( 0,15/Min) www.samsung.com/fr GERMANY 01805 - 121213 ( 0,14/Min) www.samsung.de HUNGARY 06-80-SAMSUNG (7267864) www.samsung.com/hu ITALIA 800-SAMSUNG (7267864) www.samsung.com/it LUXEMBURG 0032 (0)2 201 24 18 www.samsung.lu NETHERLANDS 0900 20 200 88 ( 0,10/Min) www.samsung.com/nl NORWAY 815-56 480 www.samsung.com/no POLAND 0 801 801 881 www.samsung.com/pl PORTUGAL 80 8 200 128 www.samsung.com/pt SLOVAKIA 0800-SAMSUNG (726786) www.samsung.com/sk SPAIN 902 10 11 30 www.samsung.com/es SWEDEN 0771-400 200 www.samsung.com/se U.K 0870 SAMSUNG (7267864) www.samsung.com/uk Republic of Ireland 0818 717 100 www.samsung.com/uk Switzerland 0800-7267864 www.samsung.com/ch

CIS

RUSSIA 8-800-200-0400 www.samsung.ru KAZAHSTAN 8-800-080-1188 www.samsung.kz UZBEKISTAN 8-800-120-0400 www.samsung.uz UKRAINE 8-800-502-0000 www.samsung.com/ur LITHUANIA 8-800-77777 www.samsung.lt LATVIA 800-7267 www.samsung.com/lv/index.htm ESTONIA 800-7267 www.samsung.ee

Asia Paci c

AUSTRALIA 1300 362 603 www.samsung.com/au CHINA 800-810-5858, 010-6475 1880 www.samsung.com.cn HONG KONG 3698 - 4698 www.samsung.com/hk INDIA 3030 8282

1800 110011 www.samsung.com/in INDONESIA 0800-112-8888 www.samsung.com/id JAPAN 0120-327-527 www.samsung.com/jp MALAYSIA 1800-88-9999 www.samsung.com/my PHILIPPINES 1800-10-SAMSUNG (7267864) www.samsung.com/ph SINGAPORE 1800-SAMSUNG (7267864) www.samsung.com/sg THAILAND 1800-29-3232

02-689-3232 www.samsung.com/th TAIWAN 0800-329-999 www.samsung.com/tw VIETNAM 1 800 588 889 www.samsung.com/vn

Middle East & Africa SOUTH AFRICA 0860 7267864 (SAMSUNG) www.samsung.com/za

U.A.E 800SAMSUNG (7267864) 8000-4726 www.samsung.com/mea

0137

Manualsnet FAQs

If you want to find out how the DVD-AR650 Samsung works, you can view and download the Samsung DVD-AR650 DVD Player User Manual on the Manualsnet website.

Yes, we have the User Manual for Samsung DVD-AR650 as well as other Samsung manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The User Manual should include all the details that are needed to use a Samsung DVD-AR650. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Samsung DVD-AR650 DVD Player User Manual is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Samsung DVD-AR650 DVD Player User Manual consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Samsung DVD-AR650 DVD Player User Manual free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Samsung DVD-AR650 DVD Player User Manual, simply download the document to your computer. Once downloaded, open the PDF file and print the Samsung DVD-AR650 DVD Player User Manual as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.