B p Y fig
T re th to au fig.stsp.e
Normal direction When facing to the rear
RearFront RearFront
d ilizer, first
e speaker box
t rds with the p d
pedal board. i edal is in firm h nt screws
s at right and e openings in en slide the in place.
y he front and
e s pinched.
i oth front to
n attachment a right and left).
9. Connect the speaker cable extending from the rear of the speaker box to the DP-970s speaker connector. Press the speaker cable completely into the connector so that it is securely fastened.
fig.st8.e
* Use the speaker cable with the ferrite core left attached to the cable. The DP-970 cannot be used with the ferrite core removed.
10. Connect the pedal cables to the Pedal jack.
11. As necessary, affix cord clamps as shown in the diagram to fasten the pedal cable.
fig.st9.e
When Moving the Instrument Disconnect the power cord and cables from the DP-970. Then lift the piano while keeping it level, and move it with care, so that you do not drop it on your feet, or get your hands caught.
Loosen the screws (in four places).
Attachment screws
Please dont get your fingers pinc
DP-970 Rear
Hold and insert the cable so that the clip portion extends into the stand and is securely connected.
Speaker Connecter
Speaker cable
Clip Portion Ferrite Core
Cord Clamps
Pedal Cord
Power Cord
Speaker Cord
D
stabilizer. on the stab
securing th
he side boa laces). in Step 5.
t fasten the ng that the p e attachme
(one each ano with th e board, th ws are held
grasp it at t
t your finger
s centered, b
d with the ch for the
rd
Assembling the DP-970 Make sure that another person is on hand to help with the assembly and setup. To move the piano, lift it carefully-all the while keeping it level. Be very careful, when you assemble and move the piano, to make sure that you do not drop it on your hands or feet. Should you remove screws, cord clamps, or stabilizer, make sure to put them in a safe place out of childrens reach, so there is no chance of them being swallowed accidentally.
Check the Parts efore you begin assembling the DP-970, check that all the arts were supplied. ou will also need to have a Phillips screwdriver. .st900parts.e
1: Attachment screw (M6 x 20 mm) x 8 2: Stabilizer screw (M4 x 16 mm) x 6 3: Cord clamp x 4
he speaker box can also be installed so that it faces toward the ar instead of toward the front. Having the speaker box face out e rear of the instrument allows the speakers to be directed ward listeners when the back of the instrument faces the dience.
When securing the screws, lay the entire unit sideways with the rear side of the DP-970 at the bottom.
1. Secure the left side board to the speaker box with the attachment screws (in two places). Attach so that the speaker cable at the rear of the speaker box is directed to the right.
2. Secure the right side board to the speaker box with the attachment screws (in two places).
fig.st1.e
3. Set the stabilizer in the holes in the side boards (in six places).
fig.st3.e
Take care not to attach the left and right stabilizer to the wrong sides.
fig.st900SAP
3
2
1
Speaker box Stabilizer (left)
Stabilizer (right)
Side board (right)
Side board (left) DP-970
Pedal Board
1 2
Speaker box
Side board left
Attachment screw
Side board right
Stabilizer screws
5. Put the Pedal Board on the When putting the Pedal Boar loosen the attachment screws to the side boards.
fig.st5.e
6. Secure the Pedal Board to attachment screws (in two Retighten the screws loosene
fig.st6.e
To stabilize the pedals Temporarily loosen the screws tha Step on the pedal, and after verify contact with the floor, re-tighten t firmly.
7. Align the protruding screw left) on the bottom of the pi the metal fittings on the sid piano forward until the scre
* When handling the piano, firml
back. Be careful, so you do not g
Place the keyboard so that it back and left to right.
8. Fasten the piano to the sta screw (M6 x 20 mm) (one e
fig.st7.e
Pedal Boa
Check the stability of the pedal, and make adjustments as necessary.
When Disassembling Disassemble the unit by carrying out assembly Steps 1- 11 in reverse order.
When Changing the Orientation of the Speaker Box
Be sure to completely disassemble the unit, change the speaker box orientation, then reassemble it.
7
8
hed
* 4 0 6 7 1 5 9 0 - 0 2 *
ssion of ROLAND CORPORATION. 40671590 2PD
Assembly Procedure At first, assemble the entire unit in a temporary fashion,
without really tightening the screws. Then, after checking the overall alignment of the boards (and gently shifting certain parts where necessary), go around and tightly fasten each of the screws.
Be careful when assembling the DP-970, so as to avoid scratching the side boards.
4. Raise the entire assembly. When standing the assembled unit up, grasp near the speaker box, and gently raise the assembly.
fig.st4
Speaker box
Speaker box
Attachment Screw
P-970 Copyright 2005 ROLAND CORPORATION All rights reserved. No part of this publication may be reproduced in any form without the written permi