Contents

Roland VG-88 Owner's Manual PDF

1 of 84
1 of 84

Summary of Content for Roland VG-88 Owner's Manual PDF

Thank you, and congratulations on your choice of the Roland VG-88 V- GUITAR SYSTEM.

Before using this unit, carefully read the sections entitled: IMPORTANT SAFETY INSTRUCTIONS (Owners manual p. 2), USING THE UNIT SAFELY (Owners manual p. 3), and IMPORTANT NOTES (Owners manual p. 11). These sections provide important information concerning the proper operation of the unit. Additionally, in order to feel assured that you have gained a good grasp of every feature provided by your new unit, Quick start and Owners manual should be read in its entirety. The manual should be saved and kept on hand as a convenient reference.

All product names mentioned in this document are trademarks or registered trademarks of their respective owners.

In using the VG-88, either a guitar equipped with a GK-2A or one equipped with a GK-3 can be connected to it. If using a guitar equipped with a GK-3, substitute GK Volume knob (of the GK-3) wherever SYNTH VOL knob (of the GK-2A) appears in this document.

Copyright 2000 ROLAND CORPORATION All rights reserved. No part of this publication may be reproduced in any form without the written permission of ROLAND CORPORATION.

O w

n er's M

an u

al

As of January 15, 2005 (ROLAND)

Information When you need repair service, call your nearest Roland Service Center or authorized Roland distributor in your country as shown below.

EGYPT Al Fanny Trading Office 9, EBN Hagar A1 Askalany Street, ARD E1 Golf, Heliopolis, Cairo 11341, EGYPT TEL: 20-2-417-1828

REUNION Maison FO - YAM Marcel 25 Rue Jules Hermann, Chaudron - BP79 97 491 Ste Clotilde Cedex, REUNION ISLAND TEL: (0262) 218-429

SOUTH AFRICA That Other Music Shop(PTY)Ltd. 11 Melle St., Braamfontein, Johannesbourg, SOUTH AFRICA TEL: (011) 403 4105 FAX: (011) 403 1234

Paul Bothner(PTY)Ltd. 17 Werdmuller Centre, Main Road, Claremont 7708 SOUTH AFRICA TEL: (021) 674 4030

CHINA Roland Shanghai Electronics Co.,Ltd. 5F. No.1500 Pingliang Road Shanghai 200090, CHINA TEL: (021) 5580-0800

Roland Shanghai Electronics Co.,Ltd. (BEIJING OFFICE) 10F. No.18 3 Section Anhuaxili Chaoyang District Beijing 100011 CHINA TEL: (010) 6426-5050

Roland Shanghai Electronics Co.,Ltd. (GUANGZHOU OFFICE) 2/F., No.30 Si You Nan Er Jie Yi Xiang, Wu Yang Xin Cheng, Guangzhou 510600, CHINA TEL: (020) 8736-0428

HONG KONG Tom Lee Music Co., Ltd. Service Division 22-32 Pun Shan Street, Tsuen Wan, New Territories, HONG KONG TEL: 2415 0911

Parsons Music Ltd. 8th Floor, Railway Plaza, 39 Chatham Road South, T.S.T, Kowloon, HONG KONG TEL: 2333 1863

INDIA Rivera Digitec (India) Pvt. Ltd. 409, Nirman Kendra Mahalaxmi Flats Compound Off. Dr. Edwin Moses Road, Mumbai-400011, INDIA TEL: (022) 2493 9051

INDONESIA PT Citra IntiRama J1. Cideng Timur No. 15J-150 Jakarta Pusat INDONESIA TEL: (021) 6324170

KOREA Cosmos Corporation 1461-9, Seocho-Dong, Seocho Ku, Seoul, KOREA TEL: (02) 3486-8855

MALAYSIA Roland Asia Pacific Sdn. Bhd. 45-1, Block C2, Jalan PJU 1/39, Dataran Prima, 47301 Petaling Jaya, Selangor, MALAYSIA TEL: (03) 7805-3263

PHILIPPINES G.A. Yupangco & Co. Inc. 339 Gil J. Puyat Avenue Makati, Metro Manila 1200, PHILIPPINES TEL: (02) 899 9801

SINGAPORE SWEE LEE MUSIC COMPANY PTE. LTD. 150 Sims Drive, SINGAPORE 387381 TEL: 6846-3676

CRISTOFORI MUSIC PTE LTD Blk 3014, Bedok Industrial Park E, #02-2148, SINGAPORE 489980 TEL: 6243-9555

TAIWAN ROLAND TAIWAN ENTERPRISE CO., LTD. Room 5, 9fl. No. 112 Chung Shan N.Road Sec.2, Taipei, TAIWAN, R.O.C. TEL: (02) 2561 3339

THAILAND Theera Music Co. , Ltd. 330 Verng NakornKasem, Soi 2, Bangkok 10100, THAILAND TEL: (02) 2248821

VIETNAM Saigon Music Suite DP-8 40 Ba Huyen Thanh Quan Street Hochiminh City, VIETNAM TEL: (08) 930-1969

AUSTRALIA/ NEW ZEALAND Roland Corporation Australia Pty.,Ltd. 38 Campbell Avenue Dee Why West. NSW 2099 AUSTRALIA

For Australia Tel: (02) 9982 8266 For New Zealand Tel: (09) 3098 715

ARGENTINA Instrumentos Musicales S.A. Av.Santa Fe 2055 (1123) Buenos Aires ARGENTINA TEL: (011) 4508-2700

BARBADOS A&B Music Supplies LTD 12 Webster Industrial Park Wildey, St.Michael, Barbados TEL: (246)430-1100

BRAZIL Roland Brasil Ltda. Rua San Jose, 780 Sala B Parque Industrial San Jose Cotia - Sao Paulo - SP, BRAZIL TEL: (011) 4615 5666

CHILE Comercial Fancy II S.A. Rut.: 96.919.420-1 Nataniel Cox #739, 4th Floor Santiago - Centro, CHILE TEL: (02) 688-9540

COLOMBIA Centro Musical Ltda. Cra 43 B No 25 A 41 Bododega 9 Medellin, Colombia TEL: (574)3812529

COSTA RICA JUAN Bansbach Instrumentos Musicales Ave.1. Calle 11, Apartado 10237, San Jose, COSTA RICA TEL: 258-0211

CURACAO Zeelandia Music Center Inc. Orionweg 30 Curacao, Netherland Antilles TEL:(305)5926866

DOMINICAN REPUBLIC Instrumentos Fernando Giraldez Calle Proyecto Central No.3 Ens.La Esperilla Santo Domingo, Dominican Republic TEL:(809) 683 0305

ECUADOR Mas Musika Rumichaca 822 y Zaruma Guayaquil - Ecuador TEL:(593-4)2302364

EL SALVADOR OMNI MUSIC 75 Avenida Norte y Final Alameda Juan Pablo II, Edificio No.4010 San Salvador, EL SALVADOR TEL: 262-0788

GUATEMALA Casa Instrumental Calzada Roosevelt 34-01,zona 11 Ciudad de Guatemala Guatemala TEL:(502) 599-2888

HONDURAS Almacen Pajaro Azul S.A. de C.V. BO.Paz Barahona 3 Ave.11 Calle S.O San Pedro Sula, Honduras TEL: (504) 553-2029

MARTINIQUE Musique & Son Z.I.Les Mangle 97232 Le Lamantin Martinique F.W.I. TEL: 596 596 426860

Gigamusic SARL 10 Rte De La Folie 97200 Fort De France Martinique F.W.I. TEL: 596 596 715222

MEXICO Casa Veerkamp, s.a. de c.v. Av. Toluca No. 323, Col. Olivar de los Padres 01780 Mexico D.F. MEXICO TEL: (55) 5668-6699

NICARAGUA Bansbach Instrumentos Musicales Nicaragua Altamira D'Este Calle Principal de la Farmacia 5ta.Avenida 1 Cuadra al Lago.#503 Managua, Nicaragua TEL: (505)277-2557

PANAMA SUPRO MUNDIAL, S.A. Boulevard Andrews, Albrook, Panama City, REP. DE PANAMA TEL: 315-0101

PARAGUAY Distribuidora De Instrumentos Musicales J.E. Olear y ESQ. Manduvira Asuncion PARAGUAY TEL: (595) 21 492147

PERU Audionet Distribuciones Musicales SAC Juan Fanning 530 Miraflores Lima - Peru TEL: (511) 4461388

NORWAY Roland Scandinavia Avd. Kontor Norge Lilleakerveien 2 Postboks 95 Lilleaker N-0216 Oslo NORWAY TEL: 2273 0074

POLAND MX MUSIC SP.Z.O.O. UL. Gibraltarska 4. PL-03664 Warszawa POLAND TEL: (022) 679 44 19

PORTUGAL Roland Iberia, S.L. Portugal Office Cais das Pedras, 8/9-1 Dto 4050-465, Porto, PORTUGAL TEL: 22 608 00 60

ROMANIA FBS LINES Piata Libertatii 1, 535500 Gheorgheni, ROMANIA TEL: (266) 364 609

RUSSIA MuTek 3-Bogatyrskaya Str. 1.k.l 107 564 Moscow, RUSSIA TEL: (095) 169 5043

SPAIN Roland Iberia, S.L. Paseo Garca Faria, 33-35 08005 Barcelona SPAIN TEL: 93 493 91 00

SWEDEN Roland Scandinavia A/S SWEDISH SALES OFFICE Danvik Center 28, 2 tr. S-131 30 Nacka SWEDEN TEL: (0)8 702 00 20

SWITZERLAND Roland (Switzerland) AG Landstrasse 5, Postfach, CH-4452 Itingen, SWITZERLAND TEL: (061) 927-8383

UKRAINE TIC-TAC Mira Str. 19/108 P.O. Box 180 295400 Munkachevo, UKRAINE TEL: (03131) 414-40

UNITED KINGDOM Roland (U.K.) Ltd. Atlantic Close, Swansea Enterprise Park, SWANSEA SA7 9FJ, UNITED KINGDOM TEL: (01792) 702701

BAHRAIN Moon Stores No.16, Bab Al Bahrain Avenue, P.O.Box 247, Manama 304, State of BAHRAIN TEL: 17 211 005

CYPRUS Radex Sound Equipment Ltd. 17, Diagorou Street, Nicosia, CYPRUS TEL: (022) 66-9426

IRAN MOCO INC. No.41 Nike St., Dr.Shariyati Ave., Roberoye Cerahe Mirdamad Tehran, IRAN TEL: (021) 285-4169

ISRAEL Halilit P. Greenspoon & Sons Ltd. 8 Retzif Ha'aliya Hashnya St. Tel-Aviv-Yafo ISRAEL TEL: (03) 6823666

TRINIDAD AMR Ltd Ground Floor Maritime Plaza Barataria Trinidad W.I. TEL: (868)638 6385

URUGUAY Todo Musica S.A. Francisco Acuna de Figueroa 1771 C.P.: 11.800 Montevideo, URUGUAY TEL: (02) 924-2335

VENEZUELA Instrumentos Musicales Allegro,C.A. Av.las industrias edf.Guitar import #7 zona Industrial de Turumo Caracas, Venezuela TEL: (212) 244-1122

AUSTRIA Roland Elektronische Musikinstrumente HmbH. Austrian Office Eduard-Bodem-Gasse 8, A-6020 Innsbruck, AUSTRIA TEL: (0512) 26 44 260

BELGIUM/FRANCE/ HOLLAND/ LUXEMBOURG Roland Central Europe N.V. Houtstraat 3, B-2260, Oevel (Westerlo) BELGIUM TEL: (014) 575811

CZECH REP. K-AUDIO Kardasovska 626. CZ-198 00 Praha 9, CZECH REP. TEL: (2) 666 10529

DENMARK Roland Scandinavia A/S Nordhavnsvej 7, Postbox 880, DK-2100 Copenhagen DENMARK TEL: 3916 6200

FINLAND Roland Scandinavia As, Filial Finland Elannontie 5 FIN-01510 Vantaa, FINLAND TEL: (0)9 68 24 020

GERMANY Roland Elektronische Musikinstrumente HmbH. Oststrasse 96, 22844 Norderstedt, GERMANY TEL: (040) 52 60090

GREECE STOLLAS S.A. Music Sound Light 155, New National Road Patras 26442, GREECE TEL: 2610 435400

HUNGARY Roland East Europe Ltd. Warehouse Area DEPO Pf.83 H-2046 Torokbalint, HUNGARY TEL: (23) 511011

IRELAND Roland Ireland G2 Calmount Park, Calmount Avenue, Dublin 12 Republic of IRELAND TEL: (01) 4294444

ITALY Roland Italy S. p. A. Viale delle Industrie 8, 20020 Arese, Milano, ITALY TEL: (02) 937-78300

JORDAN AMMAN Trading Agency 245 Prince Mohammad St., Amman 1118, JORDAN TEL: (06) 464-1200

KUWAIT EASA HUSAIN AL-YOUSIFI & SONS CO. Abdullah Salem Street, Safat, KUWAIT TEL: 243-6399

LEBANON Chahine S.A.L. Gerge Zeidan St., Chahine Bldg., Achrafieh, P.O.Box: 16- 5857 Beirut, LEBANON TEL: (01) 20-1441

OMAN TALENTZ CENTRE L.L.C. P.O. BOX 37, MUSCAT, POSTAL CODE 113 TEL: 931-3705

QATAR Al Emadi Co. (Badie Studio & Stores) P.O. Box 62, Doha, QATAR TEL: 4423-554

SAUDI ARABIA aDawliah Universal Electronics APL Corniche Road, Aldossary Bldg., 1st Floor, Alkhobar, SAUDI ARABIA

P.O.Box 2154, Alkhobar 31952 SAUDI ARABIA TEL: (03) 898 2081

SYRIA Technical Light & Sound Center Rawda, Abdul Qader Jazairi St. Bldg. No. 21, P.O.BOX 13520, Damascus, SYRIA TEL: (011) 223-5384

TURKEY Ant Muzik Aletleri Ithalat Ve Ihracat Ltd Sti Siraselviler Caddesi Siraselviler Pasaji No:74/20 Taksim - Istanbul, TURKEY TEL: (0212) 2449624

U.A.E. Zak Electronics & Musical Instruments Co. L.L.C. Zabeel Road, Al Sherooq Bldg., No. 14, Grand Floor, Dubai, U.A.E. TEL: (04) 3360715

CANADA Roland Canada Music Ltd. (Head Office) 5480 Parkwood Way Richmond B. C., V6V 2M4 CANADA TEL: (604) 270 6626

Roland Canada Music Ltd. (Toronto Office) 170 Admiral Boulevard Mississauga On L5T 2N6 CANADA TEL: (905) 362 9707

U. S. A. Roland Corporation U.S. 5100 S. Eastern Avenue Los Angeles, CA 90040-2938, U. S. A. TEL: (323) 890 3700

ASIA

AFRICA

AUSTRALIA/ NEW ZEALAND

EUROPE

CENTRAL/LATIN AMERICA

MIDDLE EAST NORTH AMERICA

Owners Manual

To resize thickness, move all items on the front cover to left or right

02123545 05-5-4TP

This product complies with the requirements of European Directives EMC 89/336/EEC and LVD 73/23/EEC.

For EU Countries

For EU Countries

Apparatus containing Lithium batteries

ADVARSEL! Lithiumbatteri - Eksplosionsfare ved fejlagtig hndtering. Udskiftning m kun ske med batteri af samme fabrikat og type. Levr det brugte batteri tilbage til leverandren.

VARNING Explosionsfara vid felaktigt batteribyte. Anvnd samma batterityp eller en ekvivalent typ som rekommenderas av apparattillverkaren. Kassera anvnt batteri enligt fabrikantens instruktion.

CAUTION Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Discard used batteries according to the manufacturers instructions.

ADVARSEL Eksplosjonsfare ved feilaktig skifte av batteri. Benytt samme batteritype eller en tilsvarende type anbefalt av apparatfabrikanten. Brukte batterier kasseres i henhold til fabrikantens instruks joner.

VAROITUS Paristo voi rjht, jos se on virheellisesti asennettu. Vaihda paristo ainoastaan laitevalmistajan suosittelemaan tyyppiin. Hvit kytetty paristo valmistajan ohjeiden mukaisesti.

This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.

Cet appareil numrique de la classe B respecte toutes les exigences du Rglement sur le matriel brouilleur du Canada.

NOTICE

AVIS

For the USA

FEDERAL COMMUNICATIONS COMMISSION RADIO FREQUENCY INTERFERENCE STATEMENT

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.

Unauthorized changes or modification to this system can void the users authority to operate this equipment. This equipment requires shielded interface cables in order to meet FCC class B Limit.

For Canada

2

To resize thickness, move all items on the front cover to left or right

IMPORTANT SAFETY INSTRUCTIONS

CAUTION RISK OF ELECTRIC SHOCK

DO NOT OPEN

ATTENTION: RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK).

NO USER-SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated dangerous voltage within the products enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product.

INSTRUCTIONS PERTAINING TO A RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS.

IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS

WARNING - When using electric products, basic precautions should always be followed, including the following:

1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with a dry cloth. 7. Do not block any of the ventilation openings. Install in

accordance with the manufacturers instructions. 8. Do not install near any heat sources such as radiators,

heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. When the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

WARNING: IMPORTANT:

As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows:

The wire which is coloured GREEN-AND-YELLOW must be connected to the terminal in the plug which is marked by the letter E or by the safety earth symbol or coloured GREEN or GREEN-AND-YELLOW.

The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured BLACK. The wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or coloured RED.

THIS APPARATUS MUST BE EARTHED THE WIRES IN THIS MAINS LEAD ARE COLOURED IN ACCORDANCE WITH THE FOLLOWING CODE. GREEN-AND-YELLOW: EARTH, BLUE: NEUTRAL, BROWN: LIVE

For the U.K.

10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11. Only use attachments/accessories specified by the manufacturer.

12. Never use with a cart, stand, tripod, bracket, or table except as specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

13. Unplug this apparatus during lightning storms or when unused for long periods of time.

14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

USING THE UNIT SAFELY

001 Before using this unit, make sure to read the

instructions below, and the Owners Manual.

.......................................................................................................... 002a Do not open or perform any internal modifica-

tions on the unit.

.......................................................................................................... 003 Do not attempt to repair the unit, or replace parts

within it (except when this manual provides specific instructions directing you to do so). Refer all servicing to your retailer, the nearest Roland Service Center, or an authorized Roland distributor, as listed on the Information page.

.......................................................................................................... 004 Never use or store the unit in places that are:

Subject to temperature extremes (e.g., direct sunlight in an enclosed vehicle, near a heating duct, on top of heat-generating equipment); or are

Damp (e.g., baths, washrooms, on wet floors); or are

Humid; or are

Exposed to rain; or are

Dusty; or are

Subject to high levels of vibration. .......................................................................................................... 007 Make sure you always have the unit placed so it is

level and sure to remain stable. Never place it on stands that could wobble, or on inclined surfaces.

.......................................................................................................... 008a The unit should be connected to a power supply

only of the type described in the operating instruc- tions, or as marked on the unit.

.......................................................................................................... 008e Use only the attached power-supply cord.

..........................................................................................................

009 Do not excessively twist or bend the power cord,

nor place heavy objects on it. Doing so can damage the cord, producing severed elements and short circuits. Damaged cords are fire and shock hazards!

.......................................................................................................... 010 This unit, either alone or in combination with an

amplifier and headphones or speakers, may be capable of producing sound levels that could cause permanent hearing loss. Do not operate for a long period of time at a high volume level, or at a level that is uncomfortable. If you experience any hearing loss or ringing in the ears, you should immediately stop using the unit, and consult an audiologist.

.......................................................................................................... 011 Do not allow any objects (e.g., flammable material,

coins, pins); or liquids of any kind (water, soft drinks, etc.) to penetrate the unit.

.......................................................................................................... 013 In households with small children, an adult

should provide supervision until the child is capable of following all the rules essential for the safe operation of the unit.

.......................................................................................................... 014 Protect the unit from strong impact. (Do not drop it!)

.......................................................................................................... 015 Do not force the units power-supply cord to share

an outlet with an unreasonable number of other devices. Be especially careful when using extension cordsthe total power used by all devices you have connected to the extension cords outlet must never exceed the power rating (watts/amperes) for the extension cord. Excessive loads can cause the insulation on the cord to heat up and eventually melt through.

..........................................................................................................

Used for instructions intended to alert the user to the risk of injury or material damage should the unit be used improperly.

* Material damage refers to damage or other adverse effects caused with respect to the home and all its furnishings, as well to domestic animals or pets.

Used for instructions intended to alert the user to the risk of death or severe injury should the unit be used improperly.

The symbol alerts the user to things that must be carried out. The specific thing that must be done is indicated by the design contained within the circle. In the case of the symbol at left, it means that the power- cord plug must be unplugged from the outlet.

The symbol alerts the user to important instructions or warnings.The specific meaning of the symbol is determined by the design contained within the triangle. In the case of the symbol at left, it is used for general cautions, warnings, or alerts to danger.

The symbol alerts the user to items that must never be carried out (are forbidden). The specific thing that must not be done is indicated by the design contained within the circle. In the case of the symbol at left, it means that the unit must never be disassembled.

3

016 Before using the unit in a foreign country, consult

with your retailer, the nearest Roland Service Center, or an authorized Roland distributor, as listed on the Information page.

..........................................................................................................

101a The unit should be located so that its location or

position does not interfere with its proper venti- lation.

.......................................................................................................... 102b Always grasp only the plug on the power-supply

cord when plugging into, or unplugging from, an outlet or this unit.

.......................................................................................................... 104 Try to prevent cords and cables from becoming

entangled. Also, all cords and cables should be placed so they are out of the reach of children.

.......................................................................................................... 106 Never climb on top of, nor place heavy objects on

the unit.

.......................................................................................................... 107b Never handle the power cord or its plugs with wet

hands when plugging into, or unplugging from, an outlet or this unit.

.......................................................................................................... 108a Before moving the unit, disconnect the power

plug from the outlet, and pull out all cords from external devices.

.......................................................................................................... 109a Before cleaning the unit, turn off the power and

unplug the power cord from the outlet (p. 11).

.......................................................................................................... 110a Whenever you suspect the possibility of lightning

in your area, pull the plug on the power cord out of the outlet.

..........................................................................................................

4

Contents

USING THE UNIT SAFELY......................................................................3

Concepts Behind Development of the V-Guitar System .....................8

Main features...........................................................................................9

How to use this manual........................................................................10

IMPORTANT NOTES .............................................................................11

Front and Rear Panels..........................................................................12 Front Panel................................................................................................................................................. 12 Rear Panel .................................................................................................................................................. 13

Chapter 1. Preparations for playing ....................................................14 Attaching the GK-2A/GK-3 to your guitar .......................................................................................... 14 Connecting an amp etc. ........................................................................................................................... 14 About the screen display (Basic operation) .......................................................................................... 16 Turning on the power and tuning your guitar .................................................................................... 17

Turning on the power of the VG-88 ....................................................................................... 17 Tuning your guitar ................................................................................................................... 17

Specify the driver settings....................................................................................................................... 18 Adjusting the pickup sensitivity for each string .................................................................. 20 Matching the phase of the GK pickup and the guitar pickup............................................ 21 Name the GK pickup settings ................................................................................................. 21

Playing the VG-88 (adjusting the output level) ................................................................................... 21 Selecting the connected equipment........................................................................................ 21 Playing the VG-88 ..................................................................................................................... 22

Changing sounds (patches)..................................................................................................................... 22 How patch numbers are organized........................................................................................ 22 Using the VALUE dial to change patches ............................................................................. 23 Using pedals to change patches.............................................................................................. 23

Chapter 2. Overview of the VG-88 basic knowledge.....................24 How the VG-88 produces sound............................................................................................................ 24

COSM GUITAR......................................................................................................................... 24 COSM AMP ............................................................................................................................... 24

Chapter 3. Creating sounds basic section.....................................25 Saving a sound (patch) you created (the Write operation) ................................................................ 25 Rearranging the order of patches (the Exchange function)................................................................ 25 Very simple sound editing (EZ Edit function) ..................................................................................... 26

Chapter 4. Creating sounds advanced section .............................27 COSM GUITAR settings.......................................................................................................................... 27 COSM AMP settings ................................................................................................................................ 28 EFFECTS settings...................................................................................................................................... 28 Setting the tempo and key of the song you will perform................................................................... 29 Setting the pedal functions (EXP/CTL/GK VOL/GK SW)............................................................... 29

Setting the function of the VG-88s built-in EXP pedal ....................................................... 29 Setting the function of the VG-88s built-in CTL pedal....................................................... 30 Setting the GK VOL function .................................................................................................. 30 Setting the GK SW function..................................................................................................... 31 Setting the Assign functions.................................................................................................... 31

Exchanging the connection order of the internal multi-effect and the COSM GUITAR/COSM AMP ........ 32 Combining the normal input and GK input to create a sound.......................................................... 33

Setting the balance between the GK pickup and the normal pickup................................ 33 Connecting the sound of the GK pickup at the desired location in the effects................ 33

5

Assigning a name to the patch ............................................................................................................... 34 Adjust the volume level of the patch..................................................................................................... 35 Adjusting the sound of all patches collectively ................................................................................... 35

Chapter 5. Parameter Guide.................................................................36 COSM GUITAR ........................................................................................................................................ 36

TYPE ........................................................................................................................................... 36 PICKUP ...................................................................................................................................... 37 PT SHIFT (pitch shift)............................................................................................................... 39 BODY .......................................................................................................................................... 39 TUNE .......................................................................................................................................... 40 DETUNE..................................................................................................................................... 41 PD SHIFT (pedal pitch shift) ................................................................................................... 41 POLY DISTORTION (polyphonic distortion)....................................................................... 41 POLY COMP/LIMITER (polyphonic compressor/limiter) ............................................... 42 POLY OCTAVE (polyphonic octave)..................................................................................... 42 POLY SG (polyphonic slow gear)........................................................................................... 42 FILTER........................................................................................................................................ 43 P-BEND (power bend) ............................................................................................................. 43 SUSTAIN.................................................................................................................................... 43 COLOR ....................................................................................................................................... 43 GLIDE ......................................................................................................................................... 43 PWM MOD (PWM modulation)............................................................................................. 44 ATTACK..................................................................................................................................... 44 BODY LEV (body level) ........................................................................................................... 44 ORGAN ...................................................................................................................................... 44 EQ (equalizer)............................................................................................................................ 45 PAN............................................................................................................................................. 45 MIXER......................................................................................................................................... 45

COSM AMP............................................................................................................................................... 46 EFFECTS .................................................................................................................................................... 47

COMP/LM (COMPRESSOR/LIMITER)............................................................................... 47 WAH ........................................................................................................................................... 47 EQ (equalizer)............................................................................................................................ 48 MOD (modulation) ................................................................................................................... 49 DELAY........................................................................................................................................ 53 CHORUS .................................................................................................................................... 53 REVERB...................................................................................................................................... 54 NS (noise suppressor)............................................................................................................... 54 FV (foot volume) ....................................................................................................................... 54

LEVEL/BPM/KEY................................................................................................................................... 55 PEDAL/ASSIGN...................................................................................................................................... 55 EZ EDIT ..................................................................................................................................................... 56 CONTRAST............................................................................................................................................... 56 GK FUNC (GK function) ......................................................................................................................... 57 GLOBAL .................................................................................................................................................... 58 TUNER....................................................................................................................................................... 58 OUTPUT SELECT..................................................................................................................................... 58 SYSTEM ..................................................................................................................................................... 59

DRIVER ...................................................................................................................................... 59 PEDAL........................................................................................................................................ 60 DIAL ........................................................................................................................................... 60 MIDI............................................................................................................................................ 61 EXCHANGE .............................................................................................................................. 61

6

Chapter 6. Changing the system settings ..........................................62 GK pickup settings ................................................................................................................................... 62

Select the save destination of GK pickup settings................................................................ 62 Adjusting the GK pickup sensitivity for each string ........................................................... 62 Name the GK pickup settings ................................................................................................. 62 Specify the direction in which the divided pickup is installed.......................................... 63 Specify the neck scale ............................................................................................................... 63 Specify the pickup phase ......................................................................................................... 63 Specify the distance between the divided pickup and the bridge..................................... 63 Exchanging the location of S1/S2........................................................................................... 64

Pedal function settings............................................................................................................................. 64 Setting the function of the BANK pedals .............................................................................. 64 Setting the range of bank change............................................................................................ 64 Setting the function of an external foot switch (FS-5U)....................................................... 65 Reflecting the New EXP Pedal and GK VOL Values When Patches Are Switched........ 65 Adjusting the depth of the built-in EXP pedal and the amount of change ...................... 65

VALUE dial settings................................................................................................................................. 66 Preventing accidental operation of the VALUE dial ........................................................... 66

Screen/display-related settings.............................................................................................................. 66 Adjusting the display contrast ................................................................................................ 66

GK pickup function settings ................................................................................................................... 66 Selecting the function of the S1/S2 switches ........................................................................ 66 Selecting the function of the SYNTH VOL knob.................................................................. 67

Rearranging the order of patches........................................................................................................... 67

Chapter 7. Using MIDI...........................................................................68 About MIDI ............................................................................................................................................... 68

Checking Compatible MIDI Messages (the MIDI Implementation Chart) ...................... 68 MIDI channels ........................................................................................................................... 68 About MIDI Omni Mode ......................................................................................................... 69 About the MIDI Device ID....................................................................................................... 69 Bank Select and Program Change .......................................................................................... 69

Switching the patches of an external device......................................................................................... 70 Selecting the Program Change map....................................................................................... 70 Setting the Program Change reception map......................................................................... 71 Synchronizing to the MIDI CLOCK arriving at MIDI IN ................................................... 71

Specifying the Control Change number transmitted when the pedal is operated ......................... 71 Transmitting/receiving all sound data ................................................................................................. 72

Transmitting settings to an external device (BULK DUMP) .............................................. 72 Receiving settings from an external device (BULK LOAD) ............................................... 72

Chapter 8. Appendices .........................................................................73 Troubleshooting........................................................................................................................................ 73

Trouble with the Sound ........................................................................................................... 73 Other Problems ......................................................................................................................... 73

Restoring the factory settings (Initialization) ....................................................................................... 74 MIDI Implementation Chart ................................................................................................................... 75 Specifications............................................................................................................................................. 76

Index.......................................................................................................77

VG-88 PATCH LIST ...............................................................................79

7

Concepts Behind Development of the V-Guitar System

The Process That Led to the Birth of the V-Guitar System

The acoustic piano has enjoyed a history of hundreds of years, culminating in the shape that it has today. The piano craftsmen of the past must have longed for piano wires that could be stretched just as tightly as they pleased. Unfortunately, though, the wooden frames of those times imposed practical limits on wire tension. Their dream finally became reality with the advent of frames made of cast iron. Piano craftsmen were no doubt delighted with this new ability to build pianos just as they wanted.

Guitars have had a similar history. Through a continuing process of trial, error, and improvement made in a variety of ways, including the structure and materials for the wood, strings, and paint, guitars have reached the shape they have today. Now we have electric guitars equipped with pickups and amplifiers that can produce sound at high volumes.

Does this mean that guitars have reached a state of perfection?

Not necessarily. Throughout the ages, instruments have constantly evolved through the effective use of new materials as they became available. And as the twenty-first century approaches, Roland has incorporated new materials silicon DSP chips into guitars to create a new instrument the V-Guitar System.

Sound Modeling Roland believes that the final evaluation of an electric guitars sound should not be based only on sound output from the guitar itself, but should also include the sound that passes through the guitar amps, speakers, and other equipment.

To achieve this, its necessary to simulate all the steps along the way from the moment a guitar string is plucked, until the time the sound reaches the ears thereby re-creating the sound. Roland has made it possible to re-create these steps with this latest sound modeling technology in other words, other means are used to make a virtual model of the physical structures and materials that actually exist.

Composite Object Sound Modeling: COSM

The new Composite Object Sound Modeling (COSM) advanced by Roland combines a number of sound modeling technologies to create even newer sounds. COSM creates new string vibrations while retaining all the expressiveness, response, and tension that are inherent in the sounds of a guitar.

Roland believes that the ability to produce sounds based on entirely new concepts while making full use of conventional methods of play, and the fact that these sounds have full musical value, are of the greatest importance for a guitar player.

COSM GUITAR/COSM AMP COSM guitar/COSM amp are modeling technologies that can reproduce the sounds of any existing guitar. This includes the following. Electronic Modeling, which simulates all characteristics

which can be attributed to the use of vacuum tubes, transistors, and all other electronic circuitry.

Magnetic Modeling, which simulates all the characteristics which can be produced as a result of using pickups, transformers, speakers, and other electromagnetic parts.

Physical Modeling, which simulates all the characteristics that are produced as a result of the use of certain types of materials to make a guitar, including the kind of wood, metal parts, or finish that are used.

In addition, COSM guitar is able to produce completely new sounds that never existed before. The numerous harmonics contained in the sound from the vibrating strings (the sound source) can be radically emphasized, added to, or removed, in order to create totally new guitar sounds.

A guitarist conveys musical expression through string vibration. Vibrating strings carry a great deal of information about the dynamics of a performance, including that which expresses the way in which strings have been pressed, the location at which theyve been picked, the position of the pick, and the kind of vibrato thats been used. The V-Guitar system uses the string vibration itself (which contains all of this performance information) as the sound source, and can create not only previously existing guitar sounds, but also completely new sounds. One great advantage of this system is that it preserves the playing dynamics of the guitarist, as they are conveyed by the vibration of the string.

8

Main features

A new dimension of sound- creation made possible by three core sections: COSM Guitar, COSM Amp, and multi- effects

The COSM GUITAR section allows you to change the guitars pickup and body. The COSM AMP section permits the accurate simulation of distortion, amp head, speakers, and mic placement. Finally, the versatile multi-effect section lets you put the finishing touches on your sound.

Simply by pressing a single pedal, you can switch to a different guitar, change the tuning, re-connect your amp, or change to a different effects setup.

COSM guitar technology has been further developed to allow the production of sounds that could not be made on any previously existing instrument.

The vibrations from the guitar captured by the divided pickups are analyzed to detect pitch and envelope, and are used to create sounds that are totally new, yet have a natural playing feel.

Your playing can take full advantage of the characteristic nuances provided by guitar performance techniques such as picking position, dynamics, and vibrato.

In addition, you can also use performance techniques from which pitch cannot be detected, such as muting, harmonics and brushing.

The COSM guitar section contains a mixer section that lets you freely control the inputs of the normal pickup and the divided pickup, so that you can create sounds that combine both pickups.

Rich expressive potential COSM guitar, COSM amp, and multi-effect parameters are saved in each patch. When shipped from the factory, the VG- 88 contains 160 PRESET patches. In addition, 100 new USER patches of your own creation can be stored in internal memory.

The VG-88 contains a high-quality multi-effect unit. Parameter settings for each effect can be modified and stored individually in a patch.

The COSM guitar section provides a polyphonic pitch shifter that allows you to specify a different amount of pitch shift for each string. You can play VG sounds at a different octave than the guitar sounds, or use open tunings without physically changing the actual tuning of your guitar.

A four-band equalizer allows you to make detailed adjustments to your tone.

Global parameters The patch parameters of the VG-88 can be adjusted to compensate for the environment in which you are playing.

Reverb depth, low-frequency and high-frequency tone, and noise suppressor sensitivity can be adjusted globally without changing the settings of each individual patch.

Easy operation The VG-88 features the same all-in-one pedal effector-type design that was so popular on the VG-8 and GR-30. There are no complicated connections to make, and setup is quick and easy.

The display consists of a two-digit LED and a full-graphic LCD. The two-digit LED and the LED's for each number pedal make it easy to distinguish patch numbers, even on a dimly lit stage or when changing sounds from a standing position. The 160 x 64 pixel LCD allows easy and visually intuitive parameter-editing.

Operation is consistent and logical, so that you can experience the power of the V-Guitar system immediately.

EZ Edit function (p. 26) Starting with preset sounds, you can easily create new sounds by adjusting four parameters.

Broad range of expandability

MIDI connectors (IN, OUT) You can control the VG-88 from an external MIDI device. The VG-88s parameter settings can also be transmitted to an external MIDI device and saved.

GUITAR INPUT jack A normal pickup can be plugged directly into the VG-88.

GUITAR OUTPUT jack If desired, you can output just the normal pickup sound of the guitar.

SUB EXP PEDAL/SUB CTL 1, 2 jacks An expression pedal or a control pedal can be connected to these jacks. A connected pedal can be used for controlling parameters.

Built-in EXP pedal and CTL pedal The function of the built-in EXP pedal and CTL pedal can be specified for each patch. For example, the EXP pedal can function as a wah pedal in one patch, and a volume pedal in another patch.

9

How to use this manual

This manual is broadly divided into eight chapters that explain operations and functions you will use during normal playing, as well as how to make various settings. Youll get the most from this manual by reading its chapters in order.

An alphabetical index is provided at the end of the manual. Refer to it if you encounter an unfamiliar term as you operate the VG- 88.

Chapter 1. Preparations for playing

This chapter explains how to install the GK-2A/GK-3 divided pickup on your guitar, connect it to the VG-88, and play sounds. The VG-88 has a rich array of amazing functionality. However, if connections and settings are not made correctly, this potential will not be fully realized. Please be sure to read this chapter before you turn on the VG-88s power.

It is very easy to operate the VG-88. If you master the contents of this chapter, you will be able to select the internal patches and enjoy all of the basic features of the VG-88.

Chapter 2. Overview of the VG-88 basic knowledge

This chapter provides an overview of the VG-88. It explains how the VG-88 produces sound, and describes its signal flow the way in which sound travels through the VG-88s sections.

Chapter 3. Creating sounds basic section

Once you are able to play the internal patches, you can try creating your own patches to suit any song you are playing.

This chapter explains the meaning of each patch parameter, the basic editing procedure, and how to save a patch that you create.

Chapter 4. Creating sounds advanced section

In addition to the functions explained in Chapter 3, the VG- 88 has many other advanced capabilities that are worth learning to use. This chapter explains using these various functions you will find them to be convenient when editing patches.

Chapter 5. Parameter guide This chapter provides details about the VG-88s patch parameters and system parameters, organized by screen.

This information will be useful when you wish to set up the VG-88 system for use with external devices, or when constructing a new patch. You can read the appropriate section when the need arises.

Chapter 6. Changing the system settings

This chapter explains how to make global settings for the entire VG-88.

Chapter 7. Using MIDI The VG-88 provides MIDI connectors: IN and OUT. Using MIDI, you can control the VG-88 from an external MIDI device. You can also transmit VG-88 patch parameters or system parameters to save them in an external MIDI storage device.

This chapter explains how to use the VG-88 with external devices using MIDI.

Chapter 8. Appendices This chapter provides an assortment of information not already covered in the previous chapters.

10

IMPORTANT NOTES

291b

In addition to the items listed under IMPORTANT SAFETY INSTRUCTIONS and USING THE UNIT SAFELY on pages 2 and 3, please read and observe the following:

Power Supply 301 Do not use this unit on the same power circuit with any

device that will generate line noise (such as an electric motor or variable lighting system).

307 Before connecting this unit to other devices, turn off the

power to all units. This will help prevent malfunctions and/or damage to speakers or other devices.

Placement 351 Using the unit near power amplifiers (or other equipment

containing large power transformers) may induce hum. To alleviate the problem, change the orientation of this unit; or move it farther away from the source of interference.

352a This device may interfere with radio and television

reception. Do not use this device in the vicinity of such receivers.

352b Noise may be produced if wireless communications

devices, such as cell phones, are operated in the vicinity of this unit. Such noise could occur when receiving or initi- ating a call, or while conversing. Should you experience such problems, you should relocate such wireless devices so they are at a greater distance from this unit, or switch them off.

355 To avoid possible breakdown, do not use the unit in a wet

area, such as an area exposed to rain or other moisture.

Maintenance 402 Never use benzine, thinners, alcohol or solvents of any

kind, to avoid the possibility of discoloration and/or defor- mation.

Repairs and Data 452 Please be aware that all data contained in the units

memory may be lost when the unit is sent for repairs. Important data should always be backed up in another MIDI device (e.g., a sequencer), or written down on paper (when possible). During repairs, due care is taken to avoid the loss of data. However, in certain cases (such as when circuitry related to memory itself is out of order), we regret that it may not be possible to restore the data, and Roland assumes no liability concerning such loss of data.

Memory Backup 501b This unit contains a battery which powers the units

memory circuits while the main power is off. When this battery becomes weak, the message shown below will appear in the display. Once you see this message, have the battery replaced with a fresh one as soon as possible to avoid the loss of all data in memory. To have the battery replaced, consult with your retailer, the nearest Roland Service Center, or an authorized Roland distributor, as listed on the Information page. BATTERY LOW

Additional Precautions 551 Please be aware that the contents of memory can be

irretrievably lost as a result of a malfunction, or the improper operation of the unit. To protect yourself against the risk of loosing important data, we recommend that you periodically save a backup copy of important data you have stored in the units memory in another MIDI device (e.g., a sequencer).

552 Unfortunately, it may be impossible to restore the contents of

data that was stored in the units memory or another MIDI device (e.g., a sequencer) once it has been lost. Roland Corpo- ration assumes no liability concerning such loss of data.

553 Use a reasonable amount of care when using the units

buttons, sliders, or other controls; and when using its jacks and connectors. Rough handling can lead to malfunctions.

554 Never strike or apply strong pressure to the display. 556 When connecting / disconnecting all cables, grasp the

connector itselfnever pull on the cable. This way you will avoid causing shorts, or damage to the cables internal elements.

557 A small amount of heat will radiate from the unit during

normal operation. 558a To avoid disturbing your neighbors, try to keep the units

volume at reasonable levels. You may prefer to use headphones, so you do not need to be concerned about those around you (especially when it is late at night).

559a When you need to transport the unit, package it in the box

(including padding) that it came in, if possible. Otherwise, you will need to use equivalent packaging materials.

561 Use only the specified expression pedal (EV-5; sold

separately). By connecting any other expression pedals, you risk causing malfunction and/or damage to the unit.

562 Use a cable from Roland to make the connection. If using

some other make of connection cable, please note the following precautions. Some connection cables contain resistors. Do not use

cables that incorporate resistors for connecting to this unit. The use of such cables can cause the sound level to be extremely low, or impossible to hear. For information on cable specifications, contact the manufacturer of the cable.

11

Front and Rear Panels

Front Panel fig.0-01

1. LED Display

2. LCD Display

3. VALUE Dial

4. OUTPUT LEVEL Knob

5. OUTPUT SELECT Button

6. Function Buttons

7. PAGE Buttons

8. EXIT Button

9. WRITE Button

10.CURSOR Buttons

11.COSM GUITAR Button

12.COSM AMP Button

13.EFFECTS Button

14.LEVEL/BPM/KEY Button

15.PEDAL/ASSIGN Button

16.NAME/CHAIN Button

17.EZ EDIT Button

18.TUNER Button

19.BANK Pedals

20.Number Pedals

21.CTL (control) Pedal

22.EXP (expression) Pedal

When you operate the expression pedal, please be careful not to get your fingers pinched between the movable part and the panel.

In households with small children, an adult should provide supervision until the child is capable of following all the rules essential for the safe operation of the unit.

1

2 3 4

5 6 7

10

11 12 13 14 15 16 17 18

8 9

20

22

21

19

12

Front and Rear Panels

Rear Panel fig.0-02

23.GK IN Jack

24.GUITAR Jacks

25.OUTPUT Jacks

26.PHONES Jack

27.SUB EXP PEDAL/SUB CTL 1,2 (sub expression pedal/sub control pedal) Jack

28.MIDI Connectors

29.POWER Switch

30.AC Inlet

23 26 27 29 3024 25 28

13

Chapter 1. Preparations for playing

Attaching the GK-2A/GK-3 to your guitar First, you will need to attach the GK-2A/GK-3 divided pickup to your guitar. To learn how, refer to the owners manual for the GK-2A/GK-3.

The GK-2A/GK-3 cannot be used with the following types of guitar. (When attached to one of these guitars, the GK-2A/ GK-3 will not function correctly.) Guitars with unconventional string structures, such as

twelve-string guitars or pedal steel guitars Guitars that use nylon or gut strings Bass guitars Other guitars that, for structural reasons, have no location

where the GK-2A/GK-3 divided pickup can be attached correctly

About the GK-2A/GK-3 select switch When using the VG-88, you can control the balance between the divided pickup and the normal pickup for each patch.

We recommend that you normally leave the select switch in the MIX position.

About the SYNTH VOL knob of the GK-2A When using the VG-88, various functions can be assigned to the SYNTH VOL knob of the GK-2A.

If the SYNTH VOL knob is programmed to control a parameter other than the volume of the VG-88, the SYNTH VOL knob will no longer control the volume of the VG-88.

If using a guitar equipped with a GK-3, substitute GK Volume knob (of the GK-3) wherever SYNTH VOL knob (of the GK-2A) appears in this document.

Connecting an amp etc. Before you make connections In order to play the VG-88, you will need the following equipment. A guitar on which the GK-2A/GK-3 has been installed Amp/speaker or headphones

The following equipment will add additional functionality to your VG-88 system. External expression pedal (sold separately: Roland EV-5,

BOSS FV-300L) External pedal switch (sold separately: Roland DP-2,

BOSS FS-5U)

After you have prepared your guitar by installing the GK-2A/GK-3 connect your equipment as shown in the following diagram. fig.1-01

Speakers with AmplifierGuitar with GK-2A or GK-3

Roland

14

Chapter 1. Preparations for playing

C h a p ter 1

To prevent malfunction and/or damage to speakers or other devices, always turn down the volume, and turn off the power on all devices before making any connections.

Use only the specified expression pedal (EV-5 or BOSS FV- 300L; sold separately). By connecting any other expression pedals, you risk causing malfunction and/or damage to the unit.

When connecting a FS-5U, set the polarity switch as described below.

fig.1-01a

About the GUITAR INPUT jack When connecting a guitar to the VG-88 without C-13A/B cable, use the GUITAR INPUT jack.

About the OUTPUT jack When connecting a guitar amp to the OUTPUT jacks, use the guitar amps MAIN IN jack or RETURN jack.

If your guitar amp does not have a MAIN IN jack or RETURN jack, connect it to the guitar input jack (INPUT).

About the GUITAR OUT jack As desired, connect your amp or mixer to the GUITAR OUT jack.

* Since you can output only the original guitar sound from the

GUITAR OUT jack, use the jack when you wish to process

just the guitar sound through an external effects device.

* If you are using the normal guitar input jack of the GK-2A/

GK-3, set the GK-2A/GK-3 select switch to MIX. If the

select switch is set to SYNTH (GK), the signal from

GUITAR OUT will be muted (silenced).

* Even when headphones are connected to the PHONES jack,

sound will still be output from the OUTPUT jack and the

GUITAR OUT jack.

Polarity switch

15

Chapter 1. Preparations for playing

About the screen display (Basic operation) Depending on the screen, the parameters may occupy two or more screen pages. The page icon is shown in the upper right of the screen. fig.2-02

fig.1-02

1. Use PAGE [ ][ ] to switch pages.

2. Use [F1][F6] to select parameters.

* You can also use [CURSOR] to select parameters.

3. Turn [VALUE] to select the desired value.

* If you wish to save a newly created or modified patch, refer to

Saving a sound (patch) you created (p. 25).

page icon

3

2 1 2

Edit Multiple Parameters Simultaneously For parameters which can be set independently for each string, you can simultaneously increase/decrease the settings for each string.

For example if you wish to set the shift amount of Polyphonic Pitch Shift to the same setting for all strings, this function means that you dont have to repeat the procedure for each string.

This function is available for the following parameters.

SYSTEM:

PICKUP<->BRIDGE SENSITIVITY

COSM GUITAR:

PT SHIFT SHIFT#16 PT SHIFT FINE#16 PT SHIFT HARMO#16 PT SHIFT E.LEVEL#16 PT SHIFT D.LEVEL#16 TUNE SHIFT#16 PAN STRING#16 PD SHIFT STRING#16 OCT -1OCT#16 OCT -2OCT#16 OCT DIR#16

1. Access the page that contains the parameter you

wish to modify.

2. Move the cursor to the parameter that you wish to

modify.

3. At this time, [F1] [F6] will correspond to strings

numbers 1 6. While holding down the function button for the desired string, press [F1] [F6] that you wish to modify simultaneously.

fig.1-02a

4. Press any button to cancel setting.

16

Chapter 1. Preparations for playing

C h a p ter 1

Turning on the power and tuning your guitar

Turning on the power of the VG-88

Once the connections have been completed (p. 14,15), turn on power to your various devices in the order specified. By turning on devices in the wrong order, you risk causing malfunction and/or damage to speakers and other devices.

1. Turn the VG-88s POWER switch to the ON position to

turn on its power. The display will light, and the following screen will appear. This display is referred to as the Play page.

fig.1-03

* When the power is turned on, the last-selected patch number

will be selected.

The procedures described in the owner's manual are performed from the Play page, which you can access by pressing [EXIT] several times.

This unit is equipped with a protection circuit. A brief interval (a few seconds) after power up is required before the unit will operate normally.

2. Turn on the power of your connected audio devices,

such as your guitar amp or mixer.

Tuning your guitar Heres how to use the VG-88s tuner function to tune your guitar. fig.1-04

1. Press [TUNER]. This turns on the Tuner function. fig.1-05

2. Use the function buttons to make the following settings.

Press the button ([F4] [F6]) for the function that you wish to set, and then turn [VALUE] to select the desired value.

* If you do not need to make these settings perhaps the values

you want are already selected this procedure is not

necessary. Proceed to Step 3.

[F4] (PITCH: 435Hz 445Hz)

Specify the standard pitch.

* With the factory settings, this is set to 440 Hz.

* Effects controlled with the KEY parameter make reference to

this standard pitch.

[F6] (MUTE OFF, MUTE ON)

Select whether or not sound will be output to the connected device (e.g., amp) as you tune. MUTE OFF: Sound will be output. MUTE ON: Sound will not be output.

* With the factory settings, this is set to MUTE OFF.

2

1,7

22

What is Standard pitch? Standard pitch refers to the frequency of the A4 note middle A on a piano of the instrument serving as the reference pitch for tuning.

17

Chapter 1. Preparations for playing

3. Play a single unfretted note on the string you wish to

tune. The note name closest to the string you played will appear in the LED display.

* Cleanly play a single note only on the string that you wish to tune.

fig.1-06

4. Adjust the tuning until the note name of the string you

played appears in the display.

5. While watching the display, adjust the tuning until only

the middle indicator (tuned) is lit.

6. Repeat steps 3 5 to tune all the strings.

* When tuning a guitar that has a tremolo arm, tuning one

string may cause the other strings to go out of tune. In such

cases, first tune the strings to the approximate pitch (so that

the note name is displayed), and then keep tuning each string

until they are all in tune.

7. When you have finished tuning, press [TUNER] or

[EXIT].

Specify the driver settings The sound quality of the VG-88 is dramatically affected by how the divided pickup is installed. To ensure that the VG- 88 always plays with the best possible sound quality, you must adjust the pickup driver settings. These settings provide the VG-88 with information that allows it to compensate for, and minimize, any unevenness in sound due to the nature of the divided pickups installation.

If you have two or more guitars that you wish to use with the VG-88, you must enter driver settings for the divided pickup of each guitar. For each guitar, use the following procedure. Settings for up to five guitars can be made and stored.

When playing the VG-88, driver settings are extremely important to the final sound quality. You must be sure to set these parameters correctly.

fig.1-08

1. Press [F6] (SYSTEM). The System screen will appear. fig.1-14

2. Press [F1] (DRIVER). The driver setting screen will

appear. fig.1-10

3. Specify the driver settings.

Move the cursor to SETTING. Use [VALUE] to select the driver settings for your guitar. There are five setting memories (AE), allowing you to save five setups comprised of the values you select in the following Steps 47.

You can simply select the appropriate driver setting whenever you switch guitars so that the optimal settings for that guitar are immediately available.

4. Select the driver type.

Move the cursor to TYPE. Use [VALUE] to select the

type of divided pickup that is installed on your guitar.

C C#

F# G# A A# B

D D# E F

G

3,4,5,6,7,8

3,4,5,6,7,8

2

101

18

Chapter 1. Preparations for playing

C h a p ter 1

fig.1-10a

GK-2A:

Make this setting if you are using a GK-2A/GK-3 divided pickup.

GK-2:

Make this setting if you are using a GK-2 divided pickup.

PIEZO:

Make this setting if you are using a piezo divided pickup.

* Select the Piezo setting if you are using a piezo-type pickup.

A piezo-type pickup uses a piezo-electric sensor attached to the

bridge of the guitar to detect the vibrations of the strings.

5. Specify the direction in which the pickup is attached.

Move the cursor to DIRECTION. Use [VALUE] to specify the direction in which the pickup is attached on your guitar.

fig.1-10b

NORMAL:

In this direction, the cable exits on the side of string 6. REVERSE:

In this direction, the cable exits on the side of string 1. fig.1-10c

6. Specify the scale length.

Move the cursor to SCALE. Use [VALUE] to specify the scale length of your guitar (the length from the bridge to the nut). Select the closest value in the range of 620660 mm (ST=648mm, LP=628mm).

fig.1-10d

7. Specify whether or not the functions of the GK-2A/GK-3

switches S1 and S2 will be exchanged. Move the cursor to S1/S2 POSITION, and use [VALUE] to select the setting.

fig.1-10f

NORMAL: The switch functions will be left as they are. REVERSE: The S1 switch and S2 switch will be

exchanged.

8. Specify the distance from the pickup to the bridge.

Press [PAGE ] to move to Page 2. Move the cursor to PUBRIDGE <1><6>. Use a ruler or tape measure to actually measure along each string from the center of the divided pickup to the bridge. Specify the result as the length in millimeters for each string.

* When TYPE is set to PIEZO, this setting is ignored.

fig.1-10e

fig.1-12

NORMAL

REVERSE

string 6 string 1

string 1

string 6

string 6 string 1

BridgePickup

String

19

Chapter 1. Preparations for playing

9. If you will be using two or more guitars to play the VG-

88, repeat Steps 47 to enter the driver settings for each guitar.

10.When you have finished making all of your settings,

press [EXIT]. You will return to Play page.

* These settings are required when you newly install a divided pickup on your guitar, or after you have adjusted the height of a divided pickup. Once you have made the correct settings, they will be saved even when the power is turned off. You do not need to redo these settings each time you play.

* If you are using the VG-88 with a guitar other than the one you used previously, go to Step 4 and select the appropriate driver setting AE for the guitar you are currently using. Then press [EXIT] to return to Play page.

Adjusting the pickup sensitivity for each string

Adjust the pickup sensitivity for each string according to how the GK-2A/GK-3 divided pickup was installed.

If you will be using two or more guitars to play the VG-88, you must adjust the sensitivity for the divided pickup of each guitar. For each guitar, turn off the power of the VG-88, connect the guitar, and perform the following procedure. Settings for up to five guitars can be entered and stored. fig.1-13

1. Make sure that you are in Play page.

If you are not in Play page, press [EXIT] several times.

2. Press [F6] (SYSTEM). The System screen will appear. fig.1-14

3. Press [F1] (DRIVER). The driver setting screen will

appear. fig.1-15

4. Press [PAGE ] several times to access Page 3. fig.1-16

5. Press [F6] to select String 6.

6. Play String 6 on your guitar.

Level indicators will appear beginning from the left, corresponding to how strongly you play the string.

fig.1-17

7. Turn [VALUE] to adjust the sensitivity.

Set the sensitivity as high as possible without allowing the large level indicator at the far right to appear when you play the loudest/hardest note that you will play in actual performance.

* If the large level indicator at the far right appears, the

maximum level has been exceeded and you must lower the

sensitivity.

* Depending on the guitar that you use, the level indicator may

reach the maximum even if you set sensitivity to the minimum

setting. If this occurs, increase the distance between the GK-

2A/GK-3 divided pickup and the string so that it is greater

than specified.

8. In the same way, adjust the sensitivity of Strings 51.

9. Next, play Strings 61 as softly as possible. If any string

produces a particularly loud sound, lower the sensitivity for that string in order to minimize volume differences between strings.

10.When you have finished setting the sensitivity of all of

the strings, press [EXIT]. You will return to Play page.

* These settings are required when you newly install a divided

pickup on your guitar, or after you have adjusted the height of

a divided pickup. Once you have made the correct settings,

7

3

1,10 42,5

string 1

string 6

string 1

string 6

20

Chapter 1. Preparations for playing

C h a p ter 1

they will be saved even when the power is turned off. You do

not need to redo these settings each time you play.

* If you are using the VG-88 with a guitar other than the one

you used previously, go to Step 3 and select the appropriate

driver setting AE for the guitar you are currently using.

Then press [PLAY] to return to Play page.

Matching the phase of the GK pickup and the guitar pickup

Unless the phase of the GK pickup and the pickup of the guitar are matched, they will partially cancel each other out when they are mixed, adversely affecting the tone or volume.

1. Make sure youre in Play page.

If youre not in Play page, press [EXIT] several times.

2. Press [F6] (SYSTEM).

3. Press [F1] (DRIVER).

4. Press [F5] (GT PU PHASE). fig.1-10g

5. While playing String 6, turn [VALUE] and select the

position that does not cause the volume of the low- frequency range to diminish significantly.

NORMAL: The phase will remain unchanged.

INVERSE: The phase will be inverted.

Name the GK pickup settings 1. Make sure youre in Play page.

If youre not in Play page, press [EXIT] several times.

2. Press [F6] (SYSTEM).

3. Press [F1] (DRIVER).

4. Press [F1] (SETTING). Select the SETTING item that you

wish to set.

5. Use [CURSOR ] to move the cursor to the name of the

settings. fig.6-03a

6. Use [F1] [F6] and [VALUE] to assign a name.

[F1] ( ) : Return the cursor to the left.

[F2] ( ) : Advance the cursor to the right.

[F3] ( ) : Advance the cursor to the end.

[F4] (SPACE): A space will be inserted at the cursor location, and the cursor will move one space to the right.

[F5] (DELETE): Delete a character and move the subsequent text forward.

[F6] (A, a, 1, ): Switch between inputting uppercase characters, lowercase characters, numerals, and symbols.

* Press [CURSOR ] several times to return to the previous

page.

Playing the VG-88 (adjusting the output level)

Selecting the connected equipment Select the type of equipment that is connected to the VG-88.

* If you have connected a guitar amp, refer to About the

OUTPUT jack (p. 15).

1. Press [OUTPUT SELECT] to select the output device.

* While the OUTPUT SELECT screen is displayed, you can

also rotate [VALUE] to select this.

fig.1-18

GUITAR AMP:

If you have connected the VG-88 to the guitar input jack (INPUT) of a guitar amp COMBO:

Combo type (single unit containing amp and speaker) STACK:

Stack type (amp and speaker are separate) POWER AMP+SP/RETURN:

If you have connected the VG-88 to the RETURN jack or MAIN IN jack of a guitar amp COMBO:

Combo type (single unit containing amp and speaker) STACK:

Stack type (amp and speaker are separate) LINE/PHONES:

If you have connected the VG-88 to a mixer or MTR (multitrack recorder), or are using headphones

21

Chapter 1. Preparations for playing

Playing the VG-88 Now lets actually play the VG-88.

1. Make sure that you are in Play page.

If you are not in Play page, press [EXIT] several times.

2. Set the select switch of the GK-2A/GK-3 to MIX. fig.1-19

3. Turn the VG-88s [OUTPUT LEVEL]. fig.1-19a

* The VG-88s EXP pedal, or the GK-2As SYNTH VOL knob

are set to MASTER LEVEL, operate the EXP pedal or

SYNTH VOL knob.

4. Play your guitar.

The VG-88 will sound using the currently selected patch.

Changing sounds (patches)

How patch numbers are organized In Play page, patch numbers (bank, number) and patch names are displayed as follows. fig.1-21

There are two types of patches: user patches and preset patches.

User patches When the VG-88 is shipped from the factory, it contains 100 user patches. You are free to modify, delete, or create these anew.

1-1 2-1 . . . . . 25-1 1-2 2-2 . . . . . 25-2 1-3 2-3 . . . . . 25-3 1-4 2-4 . . . . . 25-4

Preset patches The VG-88 contains 160 preset patches.

26-1 27-1 . . . . . 65-1 26-2 27-2 . . . . . 65-2 26-3 27-3 . . . . . 65-3 26-4 27-4 . . . . . 65-4

Preset patches can be edited i.e., you can modify their settings but cannot be saved again as presets. If you wish to save a modified preset patch, you must store it as a new user patch.

GK-2A GK-3

What is Patches? The VG-88 contains 260 different sounds. Each of these is called a patch.

Patch Number (Bank Number)

User Patch/ Preset Patch

Patch Name

22

Chapter 1. Preparations for playing

C h a p ter 1

Using the VALUE dial to change patches

Heres how you can change from one patch to the next one.

If the System parameter DIAL is set to VALUE ONLY, [VALUE] cannot be used to select patches.

1. Make sure that you are in Play page.

If you are not in Play page, press [EXIT] several times.

2. Turn [VALUE] to change patches.

Turning [VALUE] toward the right will select the next- numbered patch; turning it toward the left will select the previous-numbered patch.

fig.1-22

Using pedals to change patches

This method is convenient during a live performance or in the studio. You can press pedals to specify the bank and number.

If you set the System parameter BANK AREA, patches will change within the specified bank area.

1. Make sure that you are in Play page.

If you are not in Play page, press [EXIT] several times.

2. Select the patch bank.

Use [BANK ] [BANK ] to select the desired bank.

* If you do not need to leave the currently selected bank, this

step is not necessary. Proceed to Step 3.

fig.1-23

3. Select the patch number.

Use number pedals [1][4] to select the desired patch. fig.1-24

23

Chapter 2. Overview of the VG-88 basic knowledge

How the VG-88 produces sound The most basic setup for playing sounds on the VG-88 consists of the VG-88 itself and a guitar on which the GK-2A/GK-3 has been installed. Here we will provide a simple explanation of how the VG-88 produces sound. fig.2-01

COSM GUITAR This analyzes the principal components of an electric guitar, and precisely simulates the function of each of the components. The number and type of pickups, the number of strings, the tuning, and each element that plays a part in creating the tone of a guitar is digitally added to the vibration produced by the strings of your guitar.

In addition, the VG-88 detects each strings pitch and enveloping the shape of the sound. These characteristics are then digitally applied to the current patchs waveform, causing it to sound with all of the nuances of your guitar performance.

COSM AMP This allows the conditions surrounding the guitar to be simulated as well, including the type of amp head, and the positioning of the speakers and mic.

As a result, you can select from a wide variety of combinations of pickups, guitars, amps, and speakers.

Using just your own guitar, you can produce the sounds of dozens of other very different guitars.

You can also closely imitate the guitar sounds used on famous hit songs played by famous musicians. And you can take advantage of expressive possibilities that go far beyond the limits of conventional guitars.

The sounds produced by the COSM guitar and COSM amp can be mixed with the original guitar sound, and then processed using the VG-88s multi-effect unit to put the finishing touches on your sound.

Guitar sound quality Pickup Guitar amp head MicrophoneSpeakers

= + + . . .+ +

24

Chapter 3. Creating sounds basic section

C h a p ter 3

Saving a sound (patch) you created (the Write operation) The sound settings you modify are initially only temporary. When you select another patch, the modified settings will return to their original, unmodified values.

If you wish to preserve your new settings, you must perform a Write operation to save the newly created patch. fig.3-10

1. Press [WRITE]. The Write screen will appear. fig.3-11

2. Turn [VALUE] to select the desired number location for

the new patch.

By pressing [F6] (EXCHANGE) you can move to the Exchange screen (p. 25).

3. If you wish to proceed with the saving of the new patch,

press [WRITE].

* If you prefer not to save the patch, press [EXIT]. You will

return to Play page.

4. After you press [WRITE], the display will indicate

NOW WRITING, the patch will be saved, and you will return to Play page.

Rearranging the order of patches (the Exchange function) Use this when you wish to swap, or exchange, the memory location of two user patches.

It is not possible to change the order of preset patches.

fig.3-01

1. Make sure that you are in Play page.

If you are not in Play page, press [EXIT] several times.

2. Press [F6] (SYSTEM). The System screen will appear. fig.1-14

3. Press [F6] (EXCHANGE). The Exchange screen will

appear. fig.3-03

4. Press [F1] (PATCH A).

5. Turn [VALUE] to select one of the patches that you wish

to exchange.

2

1,3

4

6 2,3,8

5,7

25

Chapter 3. Creating sounds basic section

6. Press [F4] (PATCH B). fig.3-05

7. Turn [VALUE] to select the other patch that you wish to

exchange.

8. Press [F6] (EXCHANGE) to exchange the patches.

The display will indicate NOW EXCHANGING.

9. When you have finished exchange, press [EXIT] two

times. You will return to Play page.

Very simple sound editing (EZ Edit function) This method lets you create a sound by selecting one of the preset sounds and adjusting only four parameters (DRIVE, TONE, MOD, DELAY). Since you can also start with a patch and modify it, it's easy to create the desired sound even if you are not sure of the effect or settings of each effect unit. The preset sounds are classified into several Types, and each type has several Colors. fig.3-07

1. Press [EZ EDIT]. The EZ Edit screen will appear.

2. Press [F1] (TYPE), and turn [VALUE] to select the

desired TYPE.

* If you set type to PATCH DATA, you can create a sound

using the sound obtained by changing to the EZ Edit function.

ig.3-08

3. Press [F4] (COLOR), and turn [VALUE] to select a sound.

* If you have set TYPE to PATCH DATA, it will not be

possible to change the COLOR.

4. Press [F2] (DRIVE), and turn [VALUE] to adjust the

amount of distortion or sustain.

* If you have TYPE set to PATCH DATA, then when

DRIVE is set to PATCH DATA, distortion and sustain are

set to the same amount set in the original Patch data.

5. Press [F3] (TONE), and turn [VALUE] to adjust the tone.

* If you have TYPE set to PATCH DATA, then when TONE is set to PATCH DATA, distortion and sustain are set to the same amount set in the original Patch data.

6. Press [F5] (MOD), and turn [VALUE] to adjust the depth

or modulation of the sound.

* If you have TYPE set to PATCH DATA, then when MOD is set to PATCH DATA, distortion and sustain are set to the same amount set in the original Patch data.

7. Press [F6] (DELAY), and turn [VALUE] to adjust the

reverberation of the sound.

* If you have TYPE set to PATCH DATA, then when DELAY is set to PATCH DATA, distortion and sustain are set to the same amount set in the original Patch data.

8. When you are finished creating the sound, perform the

Write operation (p. 25) if you wish to save your newly created sound.

* If you do not want to save the sound, press [EXIT] to return to

Play page.

2,3,4,5,6,7

1

2

3 76

4 5

26

Chapter 4. Creating sounds advanced section

C h a p ter 4

COSM GUITAR settings Heres how to make COSM Guitar settings. You can adjust any of these settings to achieve the desired sound.

1. Press [COSM GUITAR]. fig.4-01

fig.4-02

2. Press [F1] (ON/OFF) to switch COSM GUITAR on or off.

* You can also turn [VALUE] to switch this on or off.

3. Press [F4] (TYPE), and use [VALUE] to select the COSM

GUITAR type.

COSM GUITAR TYPE (p. 36)

VARI GT ACOUSTIC NYLON STRINGS OPEN TUNE 12STRINGS PD SHIFT POLY DIST POLY COMP POLY OCT POLY SG BOWED DUAL FILTER-BASS PIPE SOLO PWM CRYSTAL ORGAN BRASS

4. Press [PAGE ].

* Pages 2 and following are the sections that determine the tone

of the [COSM GUITAR]. Each time you press [PAGE ],

you will move to the screen containing the next group of

parameters. You can also move to the next group of parameters

by pressing [COSM GUITAR].

5. Turn [VALUE] to select either ON/OFF or PRESET

in each group. fig.4-02a

fig.4-02b

6. If you wish to edit the parameters within a group in

further detail, press EDIT to move to their edit screen.

7. Press [F1][F6] for the parameter that you wish to adjust,

and use [VALUE] to select the desired value for the parameter.

8. Adjust parameters until you achieve the sound you

want.

9. When you have finished making settings, perform the

Write operation (p. 25) if you wish to save the newly created sound.

* If you do not wish to save the sound, press [EXIT] to return to

Play page.

27

Chapter 4. Creating sounds advanced section

COSM AMP settings Heres how to make COSM Amp settings. Adjust these settings until you get the sound you want.

1. Press [COSM AMP]. fig.4-03

fig.4-04

2. Press [F1] (ON/OFF) to switch COSM AMP on or off.

* You can also switch this on or off by turning [VALUE].

3. Press [F4] (TYPE), and use [VALUE] to select the COSM

AMP type.

COSM AMP TYPE (p. 46)

JC-120 CLEAN TWIN CRUNCH MATCH DRIVE VO DRIVE BLUES BG LEAD MS1959(I) MS1959(II) MS1959(I+II) SLDN LEAD METAL 5150 METAL DRIVE ACOUSTIC

4. Press [PAGE ].

* Each time you press [PAGE ], you will proceed to the

screen containing the next group of parameters. You can also

move to the next group of parameters by pressing [COSM

AMP].

5. Press [F1][F6] for the parameter that you wish to adjust,

and use [VALUE] to select the desired value for the parameter.

6. Adjust the parameter settings until you achieve the

sound you desire.

7. When you are finished making settings, perform the

Write operation (p. 25) if you wish to save your newly created sound.

* If you do not wish to save your sound, press [EXIT] to return

to Play page.

EFFECTS settings Heres how to make effect settings. You can adjust these settings as necessary to get the sound you want.

1. Press [EFFECTS]. fig.4-05

fig.4-06

2. Use [F1][F3] to turn each effect on or off.

* Each time you press [PAGE ], you will proceed to the

screen containing the next group of parameters. You can also

press [EFFECT] to proceed to the next group of parameters.

3. Turn [VALUE] to select either ON/OFF or PRESET.

4. Use [F4][F6] to select the effect that you wish to adjust.

5. Press [F1][F6] for the parameter that you wish to adjust,

and turn [VALUE] to select the desired value for the parameter.

6. Adjust the parameter settings until you achieve the

sound you want.

7. When you are finished making settings, perform the

Write operation (p. 25) if you wish to save your newly created sound.

* If you do not wish to save your sound, press [EXIT] to return

to Play page.

28

Chapter 4. Creating sounds advanced section

C h a p ter 4

Setting the tempo and key of the song you will perform You can specify the tempo and key of the song that you will be performing.

1. Press [LEVEL/BPM/KEY]. fig.4-07

fig.4-08

* For details on setting the level, refer to Adjust the volume

level of the patch (p. 35).

2. Press [F2] (BPM), and turn [VALUE] to set the tempo.

* If you wish to use BPM to control a patch parameter, set the

effect parameter to BPM . * If you are using MIDI SYNC, increase the BPM value until

MIDI appears in the display.

3. At quarter-note beats, press [F5] (BPM TAP) three or

more times at the desired tempo. The tempo will be calculated automatically, and set to the interval at which you pressed the button.

4. Press [F3] (KEY), and use [VALUE] to specify the KEY of

the COSM guitar and the Harmonist effect.

5. When you have finished making settings, perform the

Write operation (p. 25) if you wish to save them.

* If you do not wish to save the settings, press [EXIT] to return

to Play page.

Setting the pedal functions (EXP/CTL/GK VOL/GK SW) Adjust these settings if you would like to use the VG-88s EXP pedal or CTL pedal, a pedal connected to the VG-88, or an external MIDI device to control parameters as you play.

Turn on the effect that contains the parameter you wish to control.

Setting the function of the VG-88s built-in EXP pedal 1. Press [PEDAL/ASSIGN]. fig.4-09

fig.4-10

2. Press [F1] (ON/OFF) to turn the EXP pedal function on

or off.

* You can also switch this by turning [VALUE].

3. Press [F4] (EDIT). fig.4-11

4. Press [F1] (TARGET), and turn [VALUE] to select the

target.

5. Press [F4] (MIN), and turn [VALUE] to specify the

minimum value.

6. Press [F5] (MAX), and turn [VALUE] to specify the

maximum value.

7. When you have finished making settings, perform the

Write operation (p. 25) if you wish to save them.

* If you do not wish to save the settings, press [EXIT] to return

to Play page.

29

Chapter 4. Creating sounds advanced section

Setting the function of the VG- 88s built-in CTL pedal

1. Press [PEDAL/ASSIGN]. fig.4-12

fig.4-10

2. Press [F1] (ON/OFF) to switch the CTL pedal function

on or off.

* You can also switch this by turning [VALUE].

fig.4-13

3. Press [F5] (EDIT). fig.4-14a

4. Press [F1] (TARGET), and turn [VALUE] to select the

target.

5. Press [F4] (MIN), and turn [VALUE] to specify the

minimum value.

6. Press [F5] (MAX), and turn [VALUE] to specify the

maximum value.

7. Press [F6] (MODE), and turn [VALUE] to select the

desired mode.

8. When you have finished making settings, perform the

Write operation (p. 25) if you wish to save them.

* If you do not wish to save the settings, press [EXIT] to return

to Play page.

Setting the GK VOL function * Set SYNTH VOL in GK FUNK to ASSIGNABLE.

1. Press [PEDAL/ASSIGN]. fig.4-15

fig.4-10

2. Press [F3] (ON/OFF) to switch the GK VOL function on

or off.

* You can also switch this on or off by turning [VALUE].

fig.4-16

3. Press [F6] (EDIT). fig.4-17

4. Press [F1] (TARGET), and turn [VALUE] to select the

target.

5. Press [F4] (MIN), and turn [VALUE] to specify the

minimum value.

6. Press [F5] (MAX), and turn [VALUE] to specify the

maximum value.

7. When you have finished making settings, perform the

Write operation (p. 25) if you wish to save them.

* If you do not wish to save the settings, press [EXIT] to return

to Play page.

30

Chapter 4. Creating sounds advanced section

C h a p ter 4

Setting the GK SW function 1. Press [PEDAL/ASSIGN]. fig.4-18

fig.4-10

2. Press [PAGE ] to move to Page 2. fig.4-19a

3. Press [F1] (ON/OFF) to switch the GK SW function on or

off.

* You can also switch this by turning [VALUE].

4. Press [F4] (EDIT). fig.4-20

5. Press [F1] (TARGET), and turn [VALUE] to select the

target.

6. Press [F4] (MIN), and turn [VALUE] to specify the

minimum value.

7. Press [F5] (MAX), and turn [VALUE] to specify the

maximum value.

8. Press [F6] (MODE), and turn [VALUE] to select the

desired mode.

* If MODE is set to TOGGLE, the S1 switch and S2 switch

will have the same function.

9. When you have finished making settings, perform the

Write operation (p. 25) if you wish to save them.

* If you do not wish to save the settings, press [EXIT] to return

to Play page.

Setting the Assign functions Control assign settings are needed for controlling the parameters by using the EXP pedal or CTL pedal on the VG- 88 or an external pedal or MIDI device. You can set up to 8 different functions (assign numbers 1 8) to each patch number to determine which controller should control which parameter.

Heres how to make Assign 1 settings. Adjust these settings as needed for your application.

1. Press [PEDAL/ASSIGN]. fig.4-21

fig.4-10

2. Press [PAGE ] to move to Page 2. fig.4-19a

3. Press [F2] (ON/OFF) to switch the Assign function on or

off.

* You can also switch this by turning [VALUE].

fig.4-22a

4. Press [F5]. fig.4-23

5. Press [F1] (TARGET), and turn [VALUE] to select the

target.

6. Press [F4] (MIN), and turn [VALUE] to specify the

minimum value.

31

Chapter 4. Creating sounds advanced section

7. Press [F5] (MAX), and turn [VALUE] to specify the

maximum value.

8. Press [F3] (SOURCE), and turn [VALUE] to select the

desired source.

9. Press [F6] (MODE), and turn [VALUE] to select the

mode.

10.Press [PAGE ] to move to Page 2. fig.4-23a

11.Press [F1], and turn [VALUE] to specify the ACTIVE

RANGE LO value.

* If you press [F4] (LO SET), the source current value will be set.

12.Press [F2], and turn [VALUE] to specify the ACTIVE

RANGE HI value.

* If you press [F5] (HI SET), the source current value will be set.

13.When you have finished making settings, perform the

Write operation (p. 25) if you wish to save them.

* If you do not wish to save the settings, press [EXIT] to return

to Play page.

* Perform the same procedure to make settings for Assign 28.

Active Range: Control value range If a continuously variable controller such as an Expression pedal has been selected as the control source, you can specify the range of values which will affect the target parameter. The value of the target parameter will not be affected by controller movements outside this specified range, but will remain at the Maximum or Minimum value. fig.4-23b

* If you are using an on/off control source such as a foot switch,

leave this setting at LO: 0, HI: 127. Other settings may

result in the value not changing.

Exchanging the connection order of the internal multi-effect and the COSM GUITAR/COSM AMP 1. Press [NAME/CHAIN]. fig.4-24

fig.4-25

2. Press [F5] (CHAIN). fig.4-25a

fig.4-25b

3. Use [CURSOR] to select the effect that you wish to move.

4. Turn [VALUE] to move the effect.

5. When you are finished making settings, perform the

Write operation (p. 25) if you wish to save them.

* If you do not wish to save the settings, press [EXIT] to return

to Play page.

Controller Amount of Change in

Parameter Value

127

100 Max. Value

Min. Value

100 %

0 %

Controller Parameter Value

127

100

ON

OFF

Median Value

OFF Min. Value

Example; ACTIVE RANGE LO: 100 ACTIVE RANGE HI: 127

Reverb

Chorus

Delay

Modulation

Noise Suppressor

Foot Volume

Equalizer

Wah

Compressor/Limiter

COSM amp

Mixer Point

Normal pickup input

COSM guitar sound from the GK pickup

32

Chapter 4. Creating sounds advanced section

C h a p ter 4

Combining the normal input and GK input to create a sound The COSM GUITAR lets you create sounds by combining the GK pickup with the normal pickup.

Setting the balance between the GK pickup and the normal pickup

1. Press [COSM GUITAR]. fig.4-26

fig.4-27

2. Press [PAGE ] twice to move to Page 3. fig.4-28

3. Press [F6] (MIXER).

4. Press [F1] (BALANCE). fig.4-28a

5. Turn [VALUE] to set the balance between the sounds of

the normal pickup and the cosm guitar. CG: Cosm guitar NP: Normal pickup

6. When you are finished making settings, perform the

Write operation (p. 25) if you wish to save them.

* If you do not wish to save the settings, press [EXIT] to return

to Play page.

Connecting the sound of the GK pickup at the desired location in the effects

1. Press [NAME/CHAIN]. fig.4-29

fig.4-30

2. Press [F5] (CHAIN).

3. Use [CURSOR] to move to the mixer point. fig.4-30a

4. Turn [VALUE] to move the mixer point.

5. When you are finished making settings, perform the

Write operation (p. 25) if you wish to save them.

* If you do not wish to save the settings, press [EXIT] to return

to Play page.

Mixer point

33

Chapter 4. Creating sounds advanced section

Assigning a name to the patch You can assign a name to a patch you create.

1. Press [NAME/CHAIN]. fig.4-31

fig.4-32

2. Press [F4] (NAME). fig.4-33

3. Use [CURSOR] to move the cursor to the location at

which you want to select a character.

4. Turn [VALUE] to select the desired character.

As you continue turning [VALUE], the character guide will automatically change between uppercase letters, lowercase letters, numerals, and symbols. [F1][F6] have the following convenient functions.

[F1] ( ) : Return the cursor to the left.

[F2] ( ) : Advance the cursor to the right.

[F3] ( ) : Advance the cursor to the end.

[F4] (SPACE): A space will be inserted at the cursor location, and the cursor will move one space to the right.

[F5] (DELETE):

Delete a character and move the subsequent text forward.

[F6] (A, a, 1, ):

Switch between inputting uppercase characters, lowercase characters, numerals, and symbols.

5. Repeat Steps 34 to create the patch name.

6. When you have finished entering the patch name,

perform the Write operation (p. 25) if you wish to save them.

* If you do not wish to save the settings, press [EXIT] to return

to Play page.

Normal pickup sound If you use the CHAIN function to place the COSM guitar at a location other than the beginning, the normal pickup sound that is processed from the beginning of the effect chain is made available for output along with the normal pickup sound that is added by the mixer of the COSM guitar.

By using this function, you can:

1. Route only the normal pickup sound through the amp

simulator to create sounds with a greater sense of drive.

2. Use the COSM guitar section to create sounds that

combine the divided pickup with the normal pickup (for example, 12-string guitar sounds).

fig.4-30b

* If you wish have independent control of the volume with 1 in the examples above, assign the SYNTH VOL knob of the GK-2A to the effect level ahead of the COSM guitar. (p. 67)

character guide

34

Chapter 4. Creating sounds advanced section

C h a p ter 4

Adjust the volume level of the patch If the currently selected patch is louder or softer than other patches, you can adjust its level.

1. Press [LEVEL/BPM/KEY]. fig.4-34

fig.4-35

2. Press [F1] (LEVEL), and turn [VALUE] to select the

desired value. fig.4-36

3. When you are finished making settings, perform the

Write operation (p. 25) if you wish to save them.

* If you do not wish to save the settings, press [EXIT] to return

to Play page.

As an alternative to the above method, you can also use a function button in the Play page to adjust the volume level.

1. Make sure that you are in Play page.

If you are not in Play page, press [EXIT] several times.

2. Press [F1] (MST LEV) and adjust the value.

3. When you are finished making settings, perform the

Write operation (p. 25) if you wish to save them.

* If you do not wish to save the settings, press [EXIT] to return

to Play page.

Adjusting the sound of all patches collectively You can make adjustments to the sound of all patches at the same time.

If, for example, the venue at which you are playing e.g. a live concert is more reverberant than the location in which you created the patches, you can use this function to globally lower the VG-88s reverb levels instead of individually editing the reverb levels for each patch.

1. Make sure that you are in Play page.

If you are not in Play page, press [EXIT] several times.

2. Press [F5] (GLOBAL). fig.4-37

3. Press the parameter [F1][F5] that you wish to adjust,

and turn [VALUE] to select the desired value for the parameter.

4. Adjust the parameters until you get the sound you want.

35

Chapter 5. Parameter Guide

COSM GUITAR By making settings for the various elements that make up the tone of a guitar, you can create a wide variety of sounds. In addition to setting actual guitar parameters, such as pickup, body, and the pitch of each string, you can also emphasize the overtone structure, or create sounds using polyphonic effects that process each string individually.

ON/OFF Switches the COSM guitar on/off.

Selects the COSM guitar type.

VARI GT (variable guitar) This algorithm lets you make settings for the pickup, body, and the pitch of each string to specify the sound of the guitar. (PAGE2)

PICK UP (p. 37) PITCH SHIFT (p. 39) BODY (p. 39) (PAGE3)

EQ (p. 45) PAN (p. 45) MIXER (p. 45)

ACOUSTIC (acoustic guitar) This simulates the sound of an acoustic guitar. (PAGE2)

PICK UP (p. 37) BODY (p. 39) (PAGE3)

EQ (p. 45) PAN (p. 45) MIXER (p. 45)

NYLON STRINGS (nylon string guitar) This is the sound of nylon strings. (PAGE2)

BODY (p. 39) (PAGE3)

EQ (p. 45) PAN (p. 45) MIXER (p. 45)

OPEN TUNE (open tune guitar) This allows you to create open tunings by modifying the pitch of each string. (PAGE2)

PICK UP (p. 37) TUNE (p. 40) BODY (p. 39) (PAGE3)

EQ (p. 45) PAN (p. 45) MIXER (p. 45)

12STRINGS (12-string guitar) This shifts the pitch of each string and adds it to the original sound to simulate a 12-string guitar. (PAGE2)

PICK UP (p. 37) DETUNE (p. 41) BODY (p. 39) (PAGE3)

EQ (p. 45) PAN (p. 45) MIXER (p. 45)

PD SHIFT (pedal pitch shift guitar) This lets you use a pedal to change the pitch. (PAGE2)

PICK UP (p. 37) PD SHIFT (p. 41) BODY (p. 39) (PAGE3)

EQ (p. 45) PAN (p. 45) MIXER (p. 45)

POLY DIST (polyphonic distortion guitar) This independently distorts the sound of each string to create a sound that can be used for chordal playing. (PAGE2)

PICK UP (p. 37) POLY DISTORTION (p. 41) (PAGE3)

EQ (p. 45) PAN (p. 45) MIXER (p. 45)

POLY COMP (polyphonic compressor guitar) This applies a compressor to each string, providing sustain for single-note playing and preventing the volume from diminishing when chords are played. (PAGE2)

PICK UP (p. 37) POLY COMPRESSOR (p. 42) (PAGE3)

EQ (p. 45) PAN (p. 45) MIXER (p. 45)

POLY OCT (polyphonic octaver guitar) This instrument simulates an octave playing technique. (PAGE2)

PICK UP (p. 37) POLY OCTAVE (p. 42) (PAGE3)

EQ (p. 45) PAN (p. 45) MIXER (p. 45)

POLY SG (polyphonic slow gear guitar) This simulates a violin-style playing technique by fading- in the volume. (PAGE2)

PICK UP (p. 37) POLY SLOW GEAR (p. 42) (PAGE3)

EQ (p. 45) PAN (p. 45) MIXER (p. 45)

BOWED This Instrument represents stringed musical instruments played with a bow. (PAGE2)

FILTER (p. 43) P-BEND (p. 43) SUSTAIN (p. 43) (PAGE3)

EQ (p. 45) PAN (p. 45) MIXER (p. 45)

DUAL This Instrument takes the string vibration that is input and adds both distortion and portions which have the pitch glided. (PAGE2)

FILTER (p. 43) GLIDE (p. 43) SUSTAIN (p. 43) (PAGE3)

EQ (p. 45) PAN (p. 45) MIXER (p. 45)

TYPE

36

COSM GUITAR Chapter 5. Parameter Guide

C h a p ter 5

FILTER-BASS This Instrument is like a bass whose sound is passed through a filter. (PAGE2)

FILTER (p. 43) COLOR (p. 43) (PAGE3)

EQ (p. 45) PAN (p. 45) MIXER (p. 45)

PIPE This Instrument produces sounds like a soft woodwind lead instrument. (PAGE2)

FILTER (p. 43) P-BEND (p. 43) SUSTAIN (p. 43) (PAGE3)

EQ (p. 45) PAN (p. 45) MIXER (p. 45)

SOLO This is a soft lead Instrument. (PAGE2)

FILTER (p. 43) COLOR (p. 43) SUSTAIN (p. 43) (PAGE3)

EQ (p. 45) PAN (p. 45) MIXER (p. 45)

PWM (pulse-width modulation) This Instrument represents the pulse-width modulation (PWM) of an analog synthesizer. The pulse width of the waveform produced by the vibrating string is varied cyclically to create a characteristic sound. (PAGE2)

FILTER (p. 43) MOD (p. 44) SUSTAIN (p. 43) (PAGE3)

EQ (p. 45) PAN (p. 45) MIXER (p. 45)

CRYSTAL This is an Instrument providing a metallic luster. (PAGE2)

ATTACK (p. 44) BODY LEV (p. 44) SUSTAIN (p. 43) (PAGE3)

EQ (p. 45) PAN (p. 45) MIXER (p. 45)

ORGAN This is a Long Tone Instrument suitable for playing solo parts or slow songs. Like an organ, you should balance out the volume levels for the three parameters to create just the sound youre after. (PAGE2)

ORGAN (p. 44) SUSTAIN (p. 43) (PAGE3)

EQ (p. 45) PAN (p. 45) MIXER (p. 45)

BRASS This instrument detects the pitch of the electric guitar and creates a synthesizer sound. (PAGE2)

FILTER (p. 43) SUSTAIN (p. 43) (PAGE3)

EQ (p. 45) PAN (p. 45) MIXER (p. 45)

Simulates the characteristics of an electric guitar pickup.

* Cannot be turned on/off.

PRESET Select one of the pre-programmed types of pickup.

MODEL This selects the pickup arrangement to be simulated. The parameters that can be set vary according to the pickup type. LP:

Simulates the installation of two humbucking pickups (passive type).

CLA-ST (Classic ST):

Simulates the installation of three single-coil pickups (passive type).

MOD-ST (Modern ST):

Simulates the installation of three single-coil pickups (active type).

TEL:

This provides two typical single-coil pickups, producing a contemporary solid-body sound suitable for country and rocknroll.

P-90:

This provides two single-coil pickups of the type used on fixed-neck guitars and affectionately known as soap- bar or dog-ear pickups.

LIPS (lipstick):

This provides two single-coil pickups of the type used on guitars played in hard rock bands of the 70s, and characterized by an external case reminiscent of a tube of lipstick.

P.A.F.:

This provides two vintage humbucking pickups which are older than their type applied for a patent in U.S.A.

RICK:

This provides two unique single-coil pickups, producing the inimitable guitar sound used regularly by vocal groups of the 60s.

CHET:

This provides two humbucking pickups, producing the sound of the hollow-bodied guitar used in rockabilly or jazz.

S-S-H:

This provides three pickups; in order from the front they are single, single, and humbucking. This produces a contemporary active-pickup sound.

PICKUP

37

Chapter 5. Parameter Guide COSM GUITAR

VARI (variable):

This allows you to use up to two pickups of your choice, selecting from double-coil, single-coil, piezo, and acoustic. If you use double-coil or single-coil type pickups, you may freely adjust the location of the pickups.

PICKUP This is the switch that selects between the two pickups. REAR: Use the rear pickup. C+R: Use both center and rear pickups. CENTER: Use the center pickup. F+C: Use both front and center pickups. FRONT: Use the front pickup. F+R: Use both front and rear pickups.

TONE [-50+50] Adjusts the tone of the pickup. Positive (+) values will boost the high range, and negative (-) values will attenuate it.

LEVEL [0100] Sets the volume of the pickup. With a setting of 0, there will be no sound.

TYPE Selects the type of pickup. SINGLE:

Single-coil pickup. DOUBLE:

Double-coil pickup. ACOUSTIC:

A hypothetical pickup ideal for picking up the sound of an acoustic guitar.

PIEZO: Piezo pickup.

MIC:

A hypothetical mic ideal for picking up the sound of an acoustic guitar.

* If you have COSM GUITAR TYPE set to ACOUSTIC, the

SINGLE, DOUBLE, and ACOUSTIC settings then

become unavailable.

* This cannot be set to MIC if anything other than

ACOUSTIC is selected for the COSM GUITAR TYPE

setting.

PHASE When pickups FRONT and REAR are mixed, this setting determines the phase of pickup REAR relative to pickup FRONT. IN:

It will have the same phase as pickup FRONT. OUT:

It will be mixed in opposite phase. This is valid only when two pickups are being used.

* The phase setting that is part of the pickup FRONT

parameters is the same as the corresponding parameter for

pickup REAR. Modifying one of them will cause the other

parameter to change correspondingly.

POSITION [5320 mm] Specifies the distance from the bridge at which the pickup is placed. Larger values will produce the effect of the pickup being further from the bridge.

* If the Pickup Type has been set to PIEZO or ACOUSTIC

the POSITION setting will not be available.

ANGLE [-315+315 mm] This simulates the angle of the pickup relative to the strings. The setting indicates the distance from the POSITION setting that the sixth string will be located. With positive (+) settings, the sixth string will be further from the bridge. With negative (-) values, the sixth string will be closer to the bridge. With a setting of 0, the pickup will be perpendicular with the strings. fig.5-01

* If PIEZO or ACOUSTIC is selected as the pickup type,

the Angle setting will not be available.

* Angle settings which would exceed the range of the Position

setting (5320 mm) will have no effect. For example, if the

Position is set to 100 mm, and valid range of the Angle setting

will be -95+220 mm.

POSITION ANGLE

B R

ID G

E

1

2

3

4

5

6

38

COSM GUITAR Chapter 5. Parameter Guide

C h a p ter 5

Specifies the pitch shifted sound.

ON/OFF Switches the pitch shift on/off.

* Turning [VALUE] will select PRESET.

MODE Selection for the pitch shift mode. SHIFT (pitch shift):

The pitch shift amount can be set independently for each string.

HARMO (harmony):

This creates harmony that matches the key of the song being played.

When SHIFT is selected as the mode

SHIFT 16 (pitch shift) [-24+24] Adjusts the amount of pitch shift (the amount of pitch change) in semitone steps.

FINE 16 [-50+50] Make fine adjustments to the pitch shift.

* The amount of the change in the Fine 100 is equivalent to

that of the Pitch 1.

E.LEVEL 16 (effect level) [0100] Adjusts the volume of the effect sound.

D.LEVEL 16 (direct level) [0100] Adjusts the volume of the direct sound.

When HARMO is selected as the mode

HARMO 16 (harmony) [-2 +2 OCT] This determines the pitch of the sound added to the input sound, when you are making a harmony. It allows you to set it by up to 2 octaves higher or lower than the input sound.

KEY [CB] On the VG-88, you can specify the key for each patch. The COSM GUITAR HARMO and the EFFECT HARMONIST refer to the same key setting. If you change one, the other will also be changed.

E.LEVEL 16 (effect level) [0100] Adjusts the volume of the effect sound.

D.LEVEL 16 (direct level) [0100] Adjusts the volume of the direct sound.

Specifies the resonances produced by the body of the instrument.

* Cannot be turned on/off.

PRESET Select one of the pre-programmed types of body.

ATTACK [0100] Specifies the strength of the attack when you pluck the string strongly. As this setting is increased, the attack will be sharper, and the sound will be crisper.

BODY [0100] Adjusts the balance between the bypass sound and the resonant sound (body resonance) of the top plate and body. With lower settings of this value, only the bypass sound will be heard. With larger settings, only the body resonance will be heard.

* The body resonance is monophonic. This means that if this

Body parameter is set to 100, the panning of each string will

have less effect.

* To produce the sound of a solid body, set ATTACK and BODY

to 0.

* This parameter is not displayed if you have COSM GUITAR

TYPE set to NYLON STRINGS.

LOW CUT [THRU, 55.0800 Hz] Specifies the cutoff frequency of the low-cut filter for the bypass sound.

* This parameter is not displayed if you have COSM GUITAR

TYPE set to NYLON STRINGS.

LEVEL [0100] Adjusts the volume of the body. With a setting of 0, there will be no sound.

BODY-TYPE Selects the type of resonating body.

* This parameter is not displayed if you have COSM GUITAR

TYPE set to NYLON STRINGS.

FLAT:

The body of an acoustic guitar with a flat top and back. ROUND:

The body of a flat top acoustic guitar with a round back made of resin.

f HOLE:

An f-hole body with an arched top and back. This is suitable for simulating semi-acoustic or full acoustic electric guitars.

PT SHIFT (pitch shift) BODY

39

Chapter 5. Parameter Guide COSM GUITAR

METAL:

A metal body with a single round cone resonator. This is suitable for bottle-neck (slide) playing, etc.

BANJO:

The sound of a body covered in stretched skin. Changing the size will produce an effect as if the tuning were changed.

SIZE [-50+50] Specifies the size of the body. This modifies the resonant frequency to simulate changes in body size. A setting of 0 will produce a normal resonance.

RESO (resonation) [0100] Adjusts the ease with which resonance will occur.

* If you have COSM GUITAR TYPE set to NYLON

STRINGS, the range of settings values for the resonance

switches to 0-10.

* This parameter is not displayed if you have COSM GUITAR

TYPE set to NYLON STRINGS.

BOTTOM [010] Adjusts the volume of the low frequency range.

* This parameter is displayed only if you have COSM GUITAR

TYPE set to NYLON STRINGS.

You can adjust the pitch of each string to create non-standard tunings. The direct sound will not be output.

ON/OFF Switches the tune on/off.

TYPE Sets the tuning of the strings. If the shift type is USER, specify the pitch of each string. OPEN-D:

This simulates an open-D tuning. Starting from the 6th string, the strings will be pitched D, A, D, F#, A, D. The original sound will not be heard.

OPEN-E:

This simulates an open-E tuning. Starting from the 6th string, the strings will be pitched E, B, E, G#, B, E. The original sound will not be heard.

OPEN-G:

This simulates an open-G tuning. Starting from the 6th string, the strings will be pitched D, G, D, G, B, D. The original sound will not be heard.

OPEN-A:

This simulates an open-A tuning. Starting from the 6th string, the strings will be pitched E, A, E, A, C#, E. The original sound will not be heard.

DROP-D:

This lowers only the 6th string one note. Starting from the 6th string, the strings will be pitched D, A, D, G, B, E. The original sound of the 6th string will not be heard.

NASH-VILLE:

Strings 1 and 2 will sound as they are. For strings 3 6 the original sound will not be heard, and they will sound an octave higher than the original.

* When you select a TYPE, the Pitch Shift, Fine Tune, Balance,

and Level will be set automatically.

USER:

Pitch Shift, Fine Tune, Balance, and Level will be set automatically.

SHIFT 16 [-24 +24] If you have HARMONY set to USER, the amount of pitch shift is then set relative to the notes as input with C selected for the KEY parameter.

TUNE

40

COSM GUITAR Chapter 5. Parameter Guide

C h a p ter 5

A slightly pitch-shifted sound is added to the original sound of each string, producing a spacious feeling.

ON/OFF Switches the detune on/off.

DETUNE [0100] A slightly pitch-shifted sound is added to the original sound of each string.

Specifies the shift amount of the pitch-shifted sound.

ON/OFF Switches the pedal pitch shift on/off.

PITCH [-2424] Specifies the amount of pitch shift obtained when you operate the pedal.

STRING 16 [ON/OFF] Turns pedal pitch shift on/off for each string. This allows you to shift only the pitch of specific strings.

SET PDL (setting pedal) Assign the Pitch Shift function to the built-in EXP pedal.

You can individually distort the sound of each string to get a sound that can be played chordally without breaking up.

ON/OFF Switches the distortion on/off.

* Turning [VALUE] will select PRESET.

MODE Selects the type of distortion. CLA OD (clear overdrive):

A clear overdrive sound is obtained. TURBO OD (turbo overdrive):

Allows you to obtain a rich effect just like distortion, without losing the subtle nuance of the overdrive.

DS1 (distortion 1):

Allows you to obtain a standard distortion sound. DS2 (distortion 2):

Allows you to obtain a distortion sound with a rich middle.

FUZZ:

This produces a basic fuzz sound.

DRIVE [0100] This sets the degree of sound distortion.

HIGH CUT [700 Hz11.0 kHz, FLAT] Adjusts the tone of the distorted sound.

LEVEL [0100] Adjusts the output level that is raised by being distorted.

POLY BAL (poly balance) [0100] Adjusts the degree of distortion for chordal playing.

DRV BAL (drive balance) [0100] Adjusts the degree of distortion between low and high strings, to even out the volume balance.

DETUNE

PD SHIFT (pedal pitch shift)

POLY DISTORTION (polyphonic distortion)

41

Chapter 5. Parameter Guide COSM GUITAR

The compressor is an effect that attenuates loud input levels and boosts soft input levels, thus evening out the volume to create sustain without distortion.

ON/OFF Turns the compressor on/off.

* Turning [VALUE] will select PRESET.

MODE COMP: The effect will function as a compressor. LIMITER: The effect will function as a limiter.

When COMP is selected as the mode

SUSTAIN [0100] Adjusts the range (time) over which low-level signals are boosted. Larger values will result in longer sustain.

ATTACK [0100] Adjusts the strength of the picking attack. Larger values will result in a sharper attack, creating a more clearly defined sound.

TONE [-50+50] Adjusts the tone.

LEVEL [0100] Adjusts the volume.

CMP BAL (compressor balance) [0100] Adjusts the effect depth for the low strings.

When LIMITER is selected as the mode

THRESHOLD [0100] Adjust this as appropriate for the input signal from your guitar. When the input signal level exceeds this threshold level, limiting will be applied.

RELEASE [0100] This adjusts the time from when the signal level drops below the threshold until when limiting is removed.

TONE [-50+50] Adjusts the tone.

LEVEL [0100] Adjusts the volume.

CMP BAL (compressor balance) [0100] Adjusts the effect depth for the low strings.

This supports playing technique related to octaves.

ON/OFF Turns octave on/off.

* Turning [VALUE] will select PRESET.

-1OCT 16 (-1 octave) [0100] This adds sound one octave lower than the original sound.

-2OCT 16 (-2 octave) [0100] This adds sound two octaves lower than the original sound.

DIR 16 (direct) [0100] This adjusts the level of the original sound.

This produces a volume-swell effect (violin-like sound).

ON/OFF Switches the slow gear on/off.

* Turning [VALUE] will select PRESET.

RISE TIME [0100] This adjusts the time needed for the volume to reach its maximum from the moment you begin picking.

SENS (sensitivity) [0100] This adjusts the sensitivity of the slow gear. When it is set to a lower value, the effect of the slow gear can be obtained only with stronger picking, while no effect is obtained with weaker picking. When the value is set higher, the effect is obtained even with weak picking.

POLY COMP/LIMITER (polyphonic compressor/limiter)

POLY OCTAVE (polyphonic octave)

POLY SG (polyphonic slow gear)

42

COSM GUITAR Chapter 5. Parameter Guide

C h a p ter 5

The sound can be passed through a filter to adjust the brightness or character.

* Cannot be turned on/off.

PRESET Select one of the pre-programmed types of filter.

CUTOFF (cutoff frequency) [0100] This sets the brightness (hardness) of the sound. A larger value results in a brighter sound.

RESO (resonance) [0100] This sets the degree of resonance (distinctiveness) of the sound. A larger value results in a sound that is more unique and extraordinary.

TOUCH-S (touch sensitivity) [0100] This sets the sensitivity for a filter that alters the sound in response to how much force is used to play the guitar. A higher setting results in a brighter sound when the guitar strings are played with force. When set to 0, the sound does not change in keeping with how forcefully or gently the strings are played.

DECAY [0100] This sets the length of time for the decay in the distinctive sound characteristics produced when the guitar is played with force. A smaller value results in a faster decay and a softer sound.

* The decay effect cannot be obtained if the TOUCH-S value is

too low.

* This appears only when FILTER BASS is selected for the

COSM GUITAR TYPE setting.

A higher setting results in a darker sound. At the same time, the tone and volume also change with respect to fluctuations in pitch produced by using a tremolo bar or other techniques.

* Cannot be turned on/off.

PRESET Select one of the pre-programmed types of power bend.

P-BEND (power bend) [0100] The higher the value, the more strained the sound becomes.

P-BEND-Q (power bend Q) [0100] The higher the value, the more the sound will consist of mainly the harmonic components, thus creating a sound that exhibits almost no attack.

You can specify how the resulting volume will be affected by changes (loud/soft dynamics) in the guitar string vibrations that are input.

SUSTAIN [0100] Adjusts the range (time) over which low-level signals are boosted. Larger values will result in longer sustain.

COLOR [0100] In the case of FILTER BASS, this adjusts the strength of the low range. As the value is increased, the low range will become stronger. In the case of SOLO, this adjusts the strength of the overtones. As the value is increased, the overtones will become stronger.

Picking dynamics can affect the amount of pitch change over time. This is known as the Glide effect. With softly played notes for which no attack can be detected, a glide effect may not be obtainable.

* Cannot be turned on/off.

PRESET Select one of the pre-programmed types of glide.

GLD-SENS (glide sensitivity) [0100] This sets the sensitivity for a filter that changes the sound in response to how much force is used to play the guitar.

GLD-TIME (glide time) [0100] This sets the speed of the glide. Larger values result in longer glides.

* If GLD-SENS is at a relatively low value, GLD-TIME will

have less of an effect.

FILTER

P-BEND (power bend)

SUSTAIN

COLOR

GLIDE

43

Chapter 5. Parameter Guide COSM GUITAR

This changes the pulse width of the PWM waveform.

* Cannot be turned on/off.

PRESET Select one of the pre-programmed types of modulation.

DEPTH (PWM depth) [0100] This sets the depth to which the waveforms pulse width is varied. Higher values result in deeper undulations.

RATE (PWM rate) [0100] This sets the speed of the cycle at which the waveforms pulse width is varied. Higher values result in a faster cycle.

This sets the force of attack when a string is played.

* Cannot be turned on/off.

PRESET Select one of the pre-programmed types of attack.

LENGTH [0100] This sets the decay time for the attack portion of the sound. A smaller setting results in a shorter attack.

MOD-TUNE (modulation tune) [0100] This sets the tuning for the modulation applied to the attack.

MOD-DEP (modulation depth) [0100] This sets the depth of the modulation applied to the attack. Larger values result in deeper undulations.

LEVEL [0100] This sets the volume level of the attack portion.

BODY LEV [0100] This sets the volume level for the sustained portion of the sound.

This is a Long Tone Instrument suitable for playing solo parts or slow songs. Like an organ, you should balance out the volume levels for the three parameters to create just the sound youre after.

* Cannot be turned on/off.

PRESET Select one of the pre-programmed types of organ.

FEET-16 [0100] This is a Long Tone one octave lower than the guitar.

FEET-8 [0100] This is a Long Tone at the same pitch as the guitar.

FEET-4 [0100] This is a Long Tone one octave higher than the guitar.

PWM MOD (PWM modulation)

ATTACK

BODY LEV (body level)

ORGAN

44

COSM GUITAR Chapter 5. Parameter Guide

C h a p ter 5

A four-band equalizer with high and low ranges is provided. The sound processed by the effect can be boosted by frequency range before it is output.

ON/OFF Switches the equalizer on/off.

* Turning [VALUE] will select PRESET.

LEVEL [-20+20 dB] Adjusts the volume after the equalizer.

LOW G (low gain) [-20+20 dB] Adjusts the low frequency range tone.

HIGH G (high gain) [-20+20 dB] Adjusts the high frequency range tone.

L-MID G (low-middle gain) [-20+20 dB] Adjusts the low-middle frequency range tone.

H-MID G (high-middle gain) [-20+20 dB] Adjusts the high-middle frequency range tone.

L-MID F (low-middle frequency) [100 Hz10.0 kHz]

Specifies the center of the frequency range that will be adjusted by the L-MID G.

L-MID Q (low-middle Q) [0.516] Adjusts the width of the area affected by the EQ centered at the L-MID F. Higher values will narrow the area.

H-MID F (high-middle frequency) [100 Hz10.0 kHz]

Specifies the center of the frequency range that will be adjusted by the H-MID G.

H-MID Q (high-middle Q) [0.516] Adjusts the width of the area affected by the EQ centered at the H-MID F. Higher values will narrow the area.

This sets the stereo position of the sonic image for each of the strings.

* Cannot be turned on/off.

PRESET Select one of the pre-programmed types of pan.

STRING-16 [L=100, R=0L=50, R=50L=0, R=100]

This sets the left/right pan of each string.

* The output will be in monaural if it is passed through the

WAH, EQ, or COMP/LM effects.

If you wish to preserve the pan position of the COSM

GUITAR, use the Chain function to connect COSM GUITAR

after COSM AMP WAH, EQ, and COMP/LM.

This mixes the sounds of the normal pickup and the divided pickup.

BALANCE (mixer balance) [CG=0, NP=100CG=100, NP=0]

Adjusts the volume balance between the sounds of the normal pickup and the cosm guitar. CG: Cosm guitar NP: Normal pickup

PU POLA (pickup polarity) Specifies the polarity of the normal pickup and the divided pickup. NORMAL: The polarity will not be changed. INVERT: The polarity will be inverted.

LEVEL [0100] Specifies the output level of the COSM GUITAR.

EQ (equalizer) PAN

MIXER

45

46

Chapter 5. Parameter Guide COSM AMP

COSM AMP This simulates the head and speaker sections of a guitar amp.

ON/OFF Switches the COSM amp on/off.

TYPE This sets the type of the COSM amp. The distortion and tone characteristics of each amp are as shown below: JC-120:

The sound of the Roland JC-120 (Jazz Chorus 120), a favorite of pro musicians around the world.

CLEAN TWIN:

The sound of a conventional built-in tube amp. CRUNCH:

Allows you to obtain a crunch effect that creates a natural distortion.

MATCH DRIVE:

A simulation of the latest tube amp widely used in styles from blues and rock.

VO DRIVE:

Allows you to obtain the Liverpool sound of the 60s. BLUES:

A lead sound with a rich middle ideal for Blues. BG LEAD:

The sound of a tube amp typical of the late 70s to 80s, characterized by a distinctive mid-range.

MS1959(I):

The sound of a large tube amp stack that was indispensable to the British hard rock of the 70s, and is used to this day by many hard rock guitarists. A trebly sound created by using input I of the guitar amp.

MS1959(II):

A mild sound created by using input II of the guitar amp. MS1959(I+II):

The sound of connecting inputs I and II of the guitar amp in parallel, creating a sound with a stronger low end than I.

SLDN LEAD:

A tube amp sound with versatile distortion, usable in a wide range of styles.

METAL 5150:

The sound of a large tube amp, suitable for heavy metal. METAL DRIVE:

A high gain and powerful metal sound. AC.GUITAR:

This is a preamp for electric-acoustic guitars.

VOLUME [0100] Adjusts the volume and distortion of the amp.

PRESENCE [0100] Increasing this value boosts the ultra-high frequencies.

* This appears only when anything other than MATCH DRIVE or

VO DRIVE is selected for the COSM GUITAR TYPE setting.

HIGH CUT [0100] Increasing this value cuts the ultra-high frequencies.

* This appears only when anything other than MATCH DRIVE or

VO DRIVE is selected for the COSM GUITAR TYPE setting.

MASTER [0100] Adjusts the volume of the entire preamp.

BASS [0100] Adjusts the tone for the low frequency range.

MIDDLE [0100] Adjusts the tone for the middle frequency range.

TREBLE [0100] Adjusts the tone for the high frequency range.

GAIN [LOW, NORMAL, HIGH] Adjusts the distortion of the amp. Distortion will successively increase for settings of LOW, NORMAL and HIGH.

BRIGHT [ON/OFF] Turns the bright setting on/off. OFF: Bright is not used. ON: Bright is switched on to create a lighter and crisper

tone.

BALANCE [DI=100, MC=0 DI=0, MC=100] Adjusts the balance between the sound picked up by the mic and the direct sound.

SPEAKER Selects the speaker type.

* If OUTPUT SELECT is not set to LINE/PHONES, all

speakers other than ACOUSTIC are disabled. fig.5-03

MIC SET (mic setting) [CENTER, 110 cm] This simulates the microphone position. CENTER simulates the condition that the microphone is set in the middle of the speaker cone. 110 cm means that the microphone is moved away from the center of the speaker cone.

CommentsCabinet

A setting suitable for CLEAN TWIN

On Mic

Roland JC-120 Simulation

10 inch

12 inch

12 inch (two units)

12 inch (four units)

Small open-back enclosure

Open-back enclosure

Large Sealed enclosure

Large sealed enclosure

Large dual stack

On Mic

On Mic

On Mic

Off Mic

On Mic

Off Mic

OnMic

Off Mic

On Mic

Off Mic

Off Mic

Open-back enclosure

Open-back enclosure

Open-back enclosure

Open-back enclosure

Open-back enclosure

Large sealed enclosure

Large sealed enclosure

12 inch (two units)

12 inch (two units)

12 inch (two units)

12 inch (two units)

12 inch (two units)

12 inch (two units)

12 inch (four units)

12 inch (four units)

A setting suitable for CLEAN TWIN

A setting suitable for MATCH DRIVE

A setting suitable for MATCH DRIVE

A setting suitable for BG Lead

A setting suitable for BG Lead

SMALL MIDDLE JC-120 TWIN ON TWIN OFF MATCH ON MATCH OFF

BG STACK ON BG STACK OFF MS STACK ON MS STACK OFF METAL STACK

ACOUSTIC

A setting suitable for MS1959

A setting suitable for MS1959

FLAT

On Mic

Off Mic

Open-back enclosure

Open-back enclosure

12 inch (two units)

12 inch (two units)

A setting suitable for VO DRIVE

A setting suitable for VO DRIVE

VO ON VO OFF

Microphone Setting

Speaker Unit

SP Simulator Type

EFFECTS Chapter 5. Parameter Guide

C h a p ter 5

EFFECTS

The compressor is an effect that attenuates loud input levels and boosts soft input levels, thus evening out the volume to create sustain without distortion. The limiter attenuates loud input levels to prevent distortion.

ON/OFF Switches the COMP/LM on/off.

* Turning [VALUE] will select PRESET.

TYPE Select either compressor or limiter. COMP (compressor):

The effect will function as a compressor. LIMITER:

The effect will function as a limiter.

When COMP is selected as the type

SUSTAIN [0100] Adjusts the range (time) over which low-level signals are boosted. Larger values will result in longer sustain.

ATTACK [0100] Adjusts the strength of the picking attack. Larger values will result in a sharper attack, creating a more clearly defined sound.

TONE [-50+50] Adjusts the tone.

LEVEL [0100] Adjusts the volume.

When LIMITER is selected as the type

THRESHOLD [0100] Adjust this as appropriate for the input signal from your guitar. When the input signal level exceeds this threshold level, limiting will be applied.

RELEASE [0100] This adjusts the time from when the signal level drops below the threshold until when limiting is removed.

TONE [-50+50] Adjusts the tone.

LEVEL [0100] Adjusts the volume.

The wah effect creates a unique tone by changing the frequency response of a filter. Pedal wah lets you use an Expression pedal or the like to obtain real-time control of the wah effect. Auto wah creates an automatic wah by cyclically changing the filter, or by changing the filter in response to the volume of the input.

ON/OFF Switches the WAH on/off.

* Turning [VALUE] will select PRESET.

TYPE Either PEDAL WAH or AUTO WAH can be selected. PEDAL WAH:

The effect will function as a pedal wah. AUTO WAH:

The effect will function as an auto wah.

When PEDAL WAH is selected as the type

FREQ (frequency) [0100] This adjusts the center frequency of the Wah effect.

LEVEL [0100] Adjusts the volume.

SET PDL (setting pedal) Assign the Wah function to the built-in EXP pedal.

When AUTO WAH is selected as the type

MODE Selection for the wah mode. LPF (low pass filter):

This creates a wah effect over a wide frequency range. BPF (band pass filter):

This creates a wah effect in a narrow frequency

POLARITY Selection for the direction in which the filter will change in response to the input. DOWN: The frequency of the filter will rise. UP: The frequency of the filter will fall.

COMP/LM (COMPRESSOR/LIMITER) WAH

47

Chapter 5. Parameter Guide EFFECTS

SENS (sensitivity) [0100] This adjusts the sensitivity at which the filter will change in the direction determined by the polarity setting. Higher values will result in a stronger response. With a setting of 0, the strength of picking will have no effect.

FREQ (frequency) [0100] This adjusts the center frequency of the Wah effect.

PEAK [0100] Adjusts the way in which the wah effect applies to the area around the center frequency. Lower values will produce a wah effect over a wide area around the center frequency. Higher values will produce a wah effect in a narrow area around the center frequency.

* With a value of 50 a standard wah sound will be produced.

RATE [0100, BPM BPM ] Adjusts the frequency of the wah.

* When set to BPM, the value of each parameter will be set

according to the value of the BPM (p. 55) specified for each

patch. This makes it easier to achieve effect sound settings that

match the tempo of the song.

DEPTH [0100] Adjusts the depth of the auto wah effect.

LEVEL [0100] Adjusts the volume.

Adjusts the tone. Parametric control is provided for the high- mid range and low-mid range.

ON/OFF Switches the EQ on/off.

* Turning [VALUE] will select PRESET.

LEVEL [-20+20 dB] Adjusts the volume after the equalizer.

LOW G (low gain) [-20+20 dB] Adjusts the low frequency range tone.

HIGH G (high gain) [-20+20 dB] Adjusts the high frequency range tone.

L-MID G (low-middle gain) [-20+20 dB] Adjusts the low-middle frequency range tone.

H-MID G (high-middle gain) [-20+20 dB] Adjusts the high-middle frequency range tone.

L-MID F (low-middle frequency) [100 Hz10.0 kHz]

Specifies the center of the frequency range that will be adjusted by the L-MID G.

L-MID Q (low-middle Q) [0.516] Adjusts the width of the area affected by the EQ centered at the L-MID F. Higher values will narrow the area.

H-MID F (high-middle frequency) [100 Hz10.0 kHz]

Specifies the center of the frequency range that will be adjusted by the H-MID G.

H-MID Q (high-middle Q) [0.516] Adjusts the width of the area affected by the EQ centered at the H-MID F. Higher values will narrow the area.

EQ (equalizer)

48

EFFECTS Chapter 5. Parameter Guide

C h a p ter 5

This effect creates a sense of spaciousness and adds depth to the sound. It allows you to produce the impression that multiple instruments are playing, or to add a distinctive type of modulation. You can use this effect to simulate a number of instruments playing together, or to create unique undulations. There are ten types of Modulation you can select from. You can also edit each of these effects to your liking. It is also possible to switch Modulation off completely.

ON/OFF Switches the MOD on/off.

* Turning [VALUE] will select PRESET.

TYPE This selects the effect to be used from the following ones. HARMONIST:

This lets you add two-note harmony suitable for the key. P.SHIFTER (pitch shifter):

This is a pitch shifter with a maximum range of +/-2 octaves.

FLANGER:

The flanging effect gives a twisting, jet-airplane-like character to the sound.

PHASER:

By adding varied-phase portions to the direct sound, the phaser effect gives a whooshing, swirling character to the sound.

SUB EQ (sub equalizer):

This adjusts the tone. A parametric type is adopted for the high-middle and low-middle range.

2x2CHORUS:

This adds a pitch-shifted sound to the original sound, producing an effect of greater depth and spaciousness. Two separate stereo chorus units are used for the low- frequency and high-frequency ranges in order to create a more natural chorus sound.

TREMOLO:

The volume will change cyclically. PAN:

The sound will be moved cyclically between left and right.

PD SHIFT (pedal shift):

This effect lets you use the EXP pedal of the VG-88 to control the amount of pitch shift.

VIBRATO:

This effect creates vibrato by slightly modulating the pitch.

When HARMONIST is selected as the type

ON/OFF [OFF, ON] Turn on/off the two different harmonist sounds.

HARMONY [-2OCT+2OCT, USER] This determines the pitch of the sound added to the input sound, when you are making a harmony. It allows you to set it by up to 2 octaves higher or lower than the input sound. If you selected USER, you can specify the amount of pitch shift that will be applied to the input sound.

PAN [L=100 R=0 L=0 R=100] Assign the left/right location of the sound.

LEVEL [0100] Adjusts the volume of the harmonist sound.

DIR LEV (direct level) [0100] Adjusts the volume of the direct sound.

If you have HARMONY set to USER, the amount of pitch shift is then set relative to the notes as input with C selected for the KEY parameter.

fKEY [CB] Specifies the key of the song you are playing. By specifying the key, you can create harmonies that fit the key of the song. The key setting corresponds to the key of the song (#,b) as follows. fig.5-02

MOD (modulation)

Major C F B

E

A

D

Am Dm Gm Cm Fm B mMinor

Major G D A E B

Em Bm F m C

m G

mMinor

F

D m

G

E m

49

Chapter 5. Parameter Guide EFFECTS

When P.SHIFTER is selected as the type

ON/OFF [OFF, ON] Turns the two each pitch shifter sounds on/off.

MODE Selection for the pitch shifter mode. POLY:

You can play chords. MONO:

Compared with conventional pitch shifters, modulation is minimized. You should play notes individually.

SHIFT [-24+24] Adjusts the amount of pitch shift (the amount of pitch change) in semitone steps.

FINE [-50+50] Make fine adjustments to the pitch shift.

FEEDBACK [0100] This adjusts the feedback amount of the pitch shift sound.

PRE DLY [0300msec, BPM BPM ] Adjusts the time from when the direct sound is heard until the pitch shifted sounds are heard. Normally you can leave this set at 0ms.

PAN [L=100 R=0 L=0 R=100] Assign the left/right location of the sound.

LEVEL [0100] Adjusts the volume of the pitch shifter sound.

DIR LEV (direct level) [0100] Adjusts the volume of the direct sound.

When FLANGER is selected as the type

RATE [0100, BPM BPM ] This sets the rate of the flanging effect.

* When set to BPM, the value of each parameter will be set

according to the value of the BPM (p. 55) specified for each

patch. This makes it easier to achieve effect sound settings that

match the tempo of the song.

DEPTH [0100] Determines the depth of the flanging effect.

MANUAL [0100] Adjusts the center frequency at which to apply the effect.

RESO (resonance) [0100] Determines the amount of resonance (feedback). Increasing the value will emphasize the effect, creating a more unusual sound.

SEPARATE (separation) [0100] Adjusts the diffusion. The diffusion increases as the value increases.

LEVEL [0100] Adjusts the volume of the flanger sound.

50

EFFECTS Chapter 5. Parameter Guide

C h a p ter 5

When PHASER is selected as the type

RATE [0100, BPM BPM ] This sets the rate of the phaser effect.

* When set to BPM, the value of each parameter will be set

according to the value of the BPM (p. 55) specified for each

patch. This makes it easier to achieve effect sound settings that

match the tempo of the song.

DEPTH [0100] Determines the depth of the phaser effect.

MANUAL [0100] Adjusts the center frequency of the phaser effect.

RESO (resonance) [0100] Determines the amount of resonance (feedback). Increasing the value will emphasize the effect, creating a more unusual sound.

STAGE Selects the number of stages that the phaser effect will use. 4STAGE:

This is a four-phase effect. A light phaser effect is obtained.

8STAGE:

This is an eight-phase effect. It is a popular phaser effect. 12STAGE:

This is a twelve-phase effect. A deep phase effect is obtained.

BI-PHASE:

This is the phaser with two phase shift circuits connected in series.

STEP [OFF, 0100, BPM BPM ] Adjusts the frequency at which rate and depth will change in steps. Increasing this value will make the change occur at a finer interval.

* If this is set to BPM, the parameter values will be set

according to the BPM (p. 55) value specified for each patch.

This makes it easy to make effect sound settings that match the

song tempo.

LEVEL [0100] Adjusts the volume of the phaser sound.

When SUB EQ is selected as the type

LEVEL [-20+20 dB] Adjusts the volume after the equalizer.

LOW G (low gain) [-20+20 dB] Adjusts the low frequency range tone.

HIGH G (high gain) [-20+20 dB] Adjusts the high frequency range tone.

L-MID G (low-middle gain) [-20+20 dB] Adjusts the low-middle frequency range tone.

H-MID G (high-middle gain) [-20+20 dB] Adjusts the high-middle frequency range tone.

L-MID F (low-middle frequency) [100 Hz10.0 kHz]

Specifies the center of the frequency range that will be adjusted by the L-MID G.

L-MID Q (low-middle Q) [0.516] Adjusts the width of the area affected by the EQ centered at the L-MID F. Higher values will narrow the area.

H-MID F (high-middle frequency) [100 Hz10.0 kHz]

Specifies the center of the frequency range that will be adjusted by the H-MID G.

H-MID Q (high-middle Q) [0.516] Adjusts the width of the area affected by the EQ centered at the H-MID F. Higher values will narrow the area.

51

Chapter 5. Parameter Guide EFFECTS

When 2x2 CHORUS is selected as the type

X OVER F (crossover frequency) [100 Hz4.00 kHz]

This parameter sets the frequency at which the frequency components of the direct sound are divided into bass and treble bands.

RATE [0100, BPM BPM ] Adjusts the speed of the chorus effect.

* When set to BPM, the value of each parameter will be set

according to the value of the BPM (p. 55) specified for each

patch. This makes it easier to achieve effect sound settings that

match the tempo of the song.

DEPTH [0100] Adjusts the depth of the chorus effect. If you wish to use this as a doubling effect, use a setting of 0.

PRE DLY (pre delay) [0.040.0 msec] (0.5 msec steps)

Adjusts the time from when the direct sound is output until the effect sound is output. Extending the pre-delay will produce the sensation of multiple sounds (doubling effect).

LEVEL [0100] Adjusts the volume of the sound.

When TREMOLO or PAN is selected as the type

WAVE [0100] With TREMOLO, you can adjust the smoothness of the volume change. With PAN, you can adjust how smoothly the sound changes position.

RATE [0100, BPM BPM ] Adjusts the frequency (speed) of the change.

* When set to BPM, the value of each parameter will be set

according to the value of the BPM (p. 55) specified for each

patch. This makes it easier to achieve effect sound settings that

match the tempo of the song.

DEPTH [0100] Adjusts the depth of the effect.

When PD SHIFT is selected as the type

PITCH [-24+24] Specifies the amount of pitch shift obtained when you operate the pedal.

MODE Selection for the pedal shift mode. POLY:

You can play chords. MONO:

Compared with the conventional pitch shifter, the modulation is minimized. You should play notes individually.

SET PDL (setting pedal) Assign the Pitch Shift function to the built-in EXP pedal.

When VIBRATO is selected as the type

TRIGGER [OFF, ON] This selects on/off of the vibrato with the footswitch.

* This effect assumes that the trigger will be turned on with a

footswitch for attaining the vibrato effect.

RATE [0100, BPM BPM ] This adjusts the rate of the vibrato.

* When set to BPM, the value of each parameter will be set

according to the value of the Master BPM (p. 55) specified for

each patch. This makes it easier to achieve effect sound settings

that match the tempo of the song.

DEPTH [0100] This adjusts the depth of the vibrato.

RISE TIME [0100] This sets the time passing from the moment the trigger is turned on until the set vibrato is obtained.

52

EFFECTS Chapter 5. Parameter Guide

C h a p ter 5

This effect adds delayed sound to the direct sound, giving more body to the sound or creating special effects.

ON/OFF Switches the DELAY on/off.

* Turning [VALUE] will select PRESET.

DLY TIME (delay time) [01800 msec, BPM BPM ]

This determines the delay time.

* When set to BPM, the value of each parameter will be set

according to the value of the BPM (p. 55) specified for each

patch. This makes it easier to achieve effect sound settings that

match the tempo of the song (synchronizing the time to twice

or four times the time length of the BPM when the set time is

increased).

* To adjust the setting in 1 msec units, press [F4] (FINE).

TAP TIME [OFF, 0100%] Adjusts the delay time of the right channel delay. This setting adjusts the right channel delay time relative to the left channel delay time (considered as 100%).

FEEDBACK [0100] Feedback is returning a delay signal to the input. This parameter determines the amount of feedback. A higher value will increase the number of the delay repeats.

HIGH CUT (high-cut filter) [700 Hz11.0 kHz, FLAT]

The high-cut filter cuts the frequency contents that are higher than the set frequency. This parameter adjusts the frequency where the high-cut filter starts working. When it is set to Flat, the high-cut filter does not work at all.

DLY LEV (delay level) [0120] Adjusts the volume of the delay sound.

In this effect, a slightly detuned sound is added to the original sound to add depth and breadth.

ON/OFF Switches the CHORUS on/off.

* Turning [VALUE] will select PRESET.

MODE Selection for the chorus mode. MONO:

This chorus effect outputs the same sound from both L and R.

STEREO:

This is a stereo chorus effect that adds different chorus sounds to L and R.

RATE [0100, BPM BPM ] Adjusts the rate of the chorus effect.

* When set to BPM, the value of each parameter will be set

according to the value of the BPM (p. 55) specified for each

patch. This makes it easier to achieve effect sound settings that

match the tempo of the song.

DEPTH [0100] Adjusts the depth of the chorus effect. To use it for doubling, set the value to 0.

PRE DLY (pre delay) [0.040.0 msec] (0.5 msec steps)

Adjusts the time needed for the effect sound to be output after the direct sound has been output. By setting a longer pre delay time, you can obtain an effect that sounds like more than one sound is being played at the same time (doubling effect).

HIGH CUT (high-cut filter) [700 Hz11.0 kHz, FLAT]

The low-cut filter cuts the frequencies below the specified frequency. This setting adjusts the frequency at which the low-cut filter will begin to take effect. When FLAT is selected, the low-cut filter will have no effect.

CE LEVEL (chorus level) [0100] Adjusts the volume of the chorus sound.

DELAY CHORUS

53

Chapter 5. Parameter Guide EFFECTS

This simulates the sound that reaches the listener after being reflected from many surfaces (late reverberation).

ON/OFF Switches the REVERB on/off.

* Turning [VALUE] will select PRESET.

MODE This selects the reverb mode. ROOM 1:

Simulates the reverberation of a small room. Provides the bright reverberation of a live room.

ROOM 2:

Simulates the reverberation of a small room. Provides warm reverberations.

HALL 1:

Simulates the reverberation of a concert hall. Provides clear and spacious reverberations.

HALL 2:

Simulates the reverberation of a concert hall. Provides warm reverberations.

PLATE:

Simulates plate reverberation (a reverb unit that uses the vibration of a metallic plate). Provides a metallic sound with a distinct upper range.

REV TIME (reverb time) [0.110.0 sec] Adjusts the length (time) of reverberation.

LOW CUT (low-cut filter) [55.0 Hz800 Hz] The low-cut filter cuts the frequencies below the specified frequency. This setting adjusts the frequency at which the low-cut filter will begin to take effect.

HIGH CUT (high-cut filter) [700 Hz11.0 kHz, FLAT]

The high-cut filter cuts the frequencies above the specified frequency. This setting adjusts the frequency at which the high-cut filter will begin to take effect. When FLAT is selected, the high-cut filter will have no effect.

PRE DLY (pre delay) [0100 msec] Adjusts the time until the reverb sound appears.

DENSITY [010] This adjusts the density of the reverb sound.

REV LEV (reverb level) [0100] Adjusts the volume of the reverb sound.

This effect reduces the noise and hum picked up by guitar pickups. Since it suppresses the noise in synchronization with the envelope of the guitar sound (the way in which the guitar sound decays over time), it has very little effect on the guitar sound, and does not harm the natural character of the sound.

* Please connect the noise suppressor prior to the reverberation

type effect. This setup will prevent unnatural break of the

reverberation type effect.

ON/OFF Switches the noise suppressor on/off.

THRESHOLD [0100] Adjust this parameter as appropriate for the volume of the noise. If the noise level is high, a higher setting is appropriate. If the noise level is low, a lower setting is appropriate. Adjust this value until the decay of the guitar sound is as natural as possible.

* High settings for the threshold parameter may result in there

being no sound when you play with your guitar volume

turned down.

RELEASE [0100] Adjusts the time from when the noise suppressor begins to function until the volume reaches 0.

LEVEL [0100] This adjusts the volume.

SET PDL (setting pedal) Assign the Foot Volume function to the built-in EXP pedal.

REVERB NS (noise suppressor)

FV (foot volume)

54

Chapter 5. Parameter Guide

C h a p ter 5

LEVEL/BPM/KEY LEVEL [0200] This adjusts the output volume of the VG-88.

BPM [40BPM250BPM, MIDI] Adjusts the BPM value for each patch.

* BPM (beats per minute) indicates the number of quarter note

beats that occur each minute.

KEY [C (Am)B (G#m)] Specify the KEY of the COSM guitar and the Harmonist effect.

PEDAL/ASSIGN Adjust these settings if you would like to use the VG-88's EXP pedal or CTL pedal, a pedal connected to the VG-88, or an external MIDI device to control parameters as you play.

* Turn on the effect that contains the parameter you wish to

control.

EXP (ON/OFF) Switches the EXP pedal on/off.

* Turning [VALUE] will select PRESET.

CTL (ON/OFF) Switches the CTL pedal on/off.

* Turning [VALUE] will select PRESET.

GK VOL (ON/OFF) Switches the GK volume on/off.

* Turning [VALUE] will select PRESET.

* Set SYNTH VOL in GK FUNC to ASSIGNABLE (p. 67).

GK S1/S2 (ON/OFF) Switches the GK S1/S2 on/off.

* Turning [VALUE] will select PRESET.

* Set DOWN/S1 and UP/S2 in GK FUNC to ASSIGNABLE

(p. 66).

ASSIGN18 (ON/OFF) Switches the ASSIGN18 on/off.

* Turning [VALUE] will select PRESET.

TARGET Select the parameter that will be affected.

* Parameters listed in PEDAL/ASSIGN Parameter List (p.

81) may be set to TARGET, regardless of the COSM

GUITAR, COSM AMP, EFFECTS, and other settings.

MIN Specify the minimum value for the range of change.

MAX Specify the maximum value for the range of change.

55

Chapter 5. Parameter Guide

SOURCE Specify the MIDI data or device that will be the source of the change.

* When using GK VOL, GK S1/S2, SUB CTL1, or SUB CTL2

as the source, GK FUNC SYNTH VOL, DOWN/S1 and UP/

S2, and PEDAL SUB CTL1 and SUB CTL2 for SYSTEM,

must be set, respectively, to ASSIGNABLE (p. 65-67).

MODE Specify how the value will change in response to an operation.

When the CTL pedal or ASSIGN source is other than GK

S1/S2

NORMAL:

The value will be at MAX while the CTL pedal is pressed. The value will be at MIN when the CTL pedal is released.

TOGGLE:

The MIN and MAX values will alternate each time the CTL pedal is pressed.

For GK S1/S2

DEC/INC:

S1 will decrease the value, and S2 will increase it. TOGGLE:

The MIN and MAX values will alternate each time you press S1/S2.

* When the S1/S2 POSTION of the DRIVER (SYSTEM) is set

to "REVERSE" position, the function of S1, S2 will be

reversed.

ACTIVE RANGE Specify the valid range for the specified source device or MIDI data. LO:

Specify the minimum value for the valid range. HI:

Specify the maximum value for the valid range.

EZ EDIT This is where settings for the EZ Edit function are made.

TYPE Selects the type of EZ Edit.

* If you set type to PATCH DATA, you can create a sound

using the sound obtained by changing to the EZ Edit function.

COLOR Selects a sound.

DRIVE [0100] Adjusts the amount of distortion or sustain.

TONE [0100] Adjusts the tone.

MOD (modulation) [0100] Adjusts the depth or modulation of the sound.

DELAY [0100] Adjusts the reverberation of the sound.

CONTRAST [116] Depending on the location of the VG-88, the display may be difficult to read. In such a case, adjust the display contrast.

56

Chapter 5. Parameter Guide

C h a p ter 5

GK FUNC (GK function) Here you can specify the function of the GK pickup.

DOWN/S1 UP/S2 Specifies the function assigned to the S1 or S2 switches of the GK pickup. ASSIGNABLE:

Settings can be made in each patch as parameter control buttons.

MASTER LEVEL:

Increment or decrement the master level. PEDAL FUNC:

While holding down the S1/S2 switch of the GK-2A/ GK-3, press a VG-88 pedal to assign the function. Number pedal [1]: MASTER LEVEL down Number pedal [2]: MASTER LEVEL up Number pedal [3]: TUNER Number pedal [4]: BPM TAP VG-88 CTL pedal: Control pedal VG-88 EXP pedal: FOOT VOLUME BANK pedal: PU SELECT down BANK pedal: PU SELECT up

PATCH SELECT:

Increment or decrement the patch. PU SELECT:

Alters the position of the pickup used in the COSM GUITAR block.

TUNER/BPM:

The S1 switch will be assigned the Tuner function, and the S2 switch will be assigned the BPM (tap input) function.

* When set to anything other than ASSIGNABLE, the

PEDAL/ASSIGN GK S1/S2 and ASSIGN 1-8 SOURCE GK

S1/S2 settings are disabled.

SYNTH VOL (synth volume) Specifies the function assigned to the SYNTH VOL knob of the GK pickup. ASSIGNABLE:

The function can be set for each patch as a parameter control knob. Depending on the parameter that is assigned, the GK pickup select switch may not function.

PICKUP LEVEL:

Controls the output level of the COSM GUITAR pickup. MIXER LEVEL:

Controls the mixer level of the COSM GUITAR.

MASTER LEVEL:

Controls the MASTER LEVEL.

* When set to anything other than ASSIGNABLE, the

PEDAL/ASSIGN GK VOL and ASSIGN 1-8 SOURCE GK

S1/S2 settings are disabled.

57

Chapter 5. Parameter Guide

GLOBAL These settings allow you to make temporary adjustments that affect all Patches. This is a convenient way to make quick adjustments to suit changes in your equipment or in your performance environment.

ON/OFF Switches the Global function on/off.

LOW G (low gain) [-20 +20 dB] Adjusts the low frequency range tone.

* This adjusts the tone regardless of the equalizer on/off setting

of each patch.

HIGH G (high gain) [-20 +20 dB] Adjusts the high frequency range tone.

* This adjusts the tone regardless of the equalizer on/off setting

of each patch.

NS (noise suppressor) [-20 +20 dB] This is a -20 +20 dB adjustment to the threshold level of the noise suppressor included in each patch. If you switch to a different guitar, it is convenient to adjust this setting to match the output level of the guitar.

* If you wish to use the data set in each patch, set it to 0 dB.

* This setting will have no effect on patches in which the noise

suppressor is turned off.

REVERB [0%200%] (101 steps) This adjusts the reverb level of the reverb in each Patch by 0%200%. To obtain a more effective reverb, adjust this so you have the reverb level matched with the physical reverberation in the space where performing.

* If you wish to use the settings of each patch without change,

set this to 100%.

* This will have no effect on patches in which reverb is turned

off.

TUNER This is where settings for the Tuner function are made.

PITCH [435445 Hz] Sets the reference pitch. Effects that regulate the input pitch will use this reference pitch.

MUTE Select whether or not the tuning sound will be output to the connected device (e.g., amp). OFF: The tuning sound will be output. ON: The tuning sound will not be output.

OUTPUT SELECT This is where settings for Output Select are made.

OUTPUT SELECT Selects the type of device that is connected. GUITAR AMP:

If you have connected the VG-88 to the guitar input jack (INPUT) of a guitar amp COMBO:Combo type

(single unit containing amp and speaker) STACK: Stack type

(amp and speaker are separate) POWER AMP+SP/RETURN:

If you have connected the VG-88 to the RETURN jack or MAIN IN jack of a guitar amp COMBO:Combo type

(single unit containing amp and speaker) STACK: Stack type

(amp and speaker are separate) LINE/PHONES:

If you have connected the VG-88 to a mixer or MTR (multitrack recorder), or are using headphones

* When OUTPUT SELECT is set to GUITAR AMP or

POWER AMP+SP/RETURN, and COSM AMP SPEAKER

is set to anything other than ACOUSTIC, the SPEAKER

parameters (BALANCE, SPEAKER, MIC SET) are disabled.

58

Chapter 5. Parameter Guide

C h a p ter 5

SYSTEM This is where settings for the VG-88s operating environment are made.

This is where settings for the divided pickup are made.

SETTING [A, B, C, D, E] Up to five Driver Settings can be stored in memory. If you use more than one guitar, this provides a handy way to store the settings for each one in memory. : Return the cursor to the left. : Advance the cursor to the right. |: Advance the cursor to the end. A, a, 1, :

Switch between inputting uppercase characters, lowercase characters, numerals, and symbols.

* This is displayed if the cursor is at the name of the setting.

SPACE:

Insert a blank space.

* This is displayed if the cursor is at the name of the setting.

DELETE:

Delete a character and move the subsequent text forward.

* This is displayed if the cursor is at the name of the setting.

TYPE Set this to the type of divided picked that is mounted on your guitar. GK-2A:

Select this if you are using a GK-2A/GK-3 divided pickup.

GK-2:

Select this if you are using a GK-2 divided pickup. PIEZO:

Select this if you are using a piezo divided pickup.

DIRECTION Specifies the direction in which the divided pickup is attached. NORMAL:

In this direction, the cable exits on the side of string 6. REVERSE:

In this direction, the cable exits on the side of string 1.

SCALE [620660 mm, ST (648), LP (628)] This sets the scale length (the length from the bridge to the nut) on your guitar.

GT PU PHASE (guitar pickup phase) Sets the phase of the divided pickup and the normal pickup of your guitar.

* The sounds of the divided pickup and the normal pickup are

mixed so that you can make settings accurately.

* Set this to NORMAL, and if the low-frequency range is cut,

change the setting to INVERSE.

NORMAL:

The phase will remain unchanged. INVERSE:

The phase will be inverted.

PUBRIDGE (pickupbridge) [1030 mm] Set the distance between the GK pickup and the bridge.

* When TYPE is set to PIEZO, this setting is ignored.

SENSITIVITY [0100] Adjust the input sensitivity of the GK pickup.

S1/S2 POSITION This exchanges the function of the GK-2A/GK-3s S1/S2 switches. NORMAL:

The switch functions will be left as they are. REVERSE:

The S1 switch and S2 switch will be exchanged.

DRIVER

59

Chapter 5. Parameter Guide

Specifies the operations of the VG-88s built-in pedal and an external pedal.

BANK SW MODE (bank switch mode) Determines how the patch will change when you press the BANK pedals. WAIT NUM:

After changing the bank, press a number pedal [1][4] to switch the patch.

NUMBER 1:

When you change the bank, patch number 1 of the newly-selected bank will be chosen.

SAME NUM:

When you change the bank, the same-numbered patch as in the previously-selected bank will be chosen.

BANK AREA (MIN) [165] Specifies the lower limit of the bank pedals.

BANK AREA (MAX) [165] Specifies the upper limit of the bank pedals.

SUB CTL1 (sub control pedal 1) SUB CTL2 (sub control pedal 2) Specifies the operation of the external device connected to the SUB CTL 1,2 jack. ASSIGNABLE:

The function can be assigned by each patch as a parameter control pedal.

TUNER:

The tuner screen will be displayed. BPM(TAP):

Tap input of the MASTER BPM parameter. PU to FRONT:

Switch COSM GUITAR PICKUP sequentially toward the front pickup.

PU to REAR:

Switch COSM GUITAR PICKUP sequentially toward the rear pickup.

* When set to anything other than ASSIGNABLE, the

ASSIGN 1-8 SOURCE SUB CTL1 and SUB CTL2 settings

are disabled.

EXP/GK VOL HOLD (EXP pedal/GK volume hold)

Select whether or not the EXP and GK VOL values will be applied when a patch is recalled. ON:

The values of the various controllers will be applied when a patch is recalled. If you set the CTL pedal operation to Latch and change patches when CTL is lit, the settings at the time the patch was written will be recalled.

OFF:

The patch will be recalled with the settings of when it was written. (The values of the various controllers will be ignored.)

EXP PEDAL CALIBRATION Here's how to adjust the operation of the EXP pedal.

1. Return the built-in EXP pedal, and press [F4].

The display will indicate ARE YOU SURE?

2. If you wish to set, press [WRITE].

* If you do not wish to set the settings, press [EXIT] to return to

Play page.

3. Advance the built-in EXP pedal, and press [F6].

The display will indicate ARE YOU SURE?

4. If you wish to set, press [WRITE].

* If you do not wish to set the settings, press [EXIT] to return to

Play page.

Specifies the function of the VALUE dial.

FUNCTION Selects the function of the VALUE dial. P.NUMBER&VALUE:

In the Play page, the dial will change patches. In Edit screens, it will function as a value dial.

VALUE ONLY:

It will function only as a value dial in Edit screens.

PEDAL

DIAL

60

Chapter 5. Parameter Guide

C h a p ter 5

These are the settings for MIDI-related functions.

CHANNEL [116] Selects the MIDI channel used for receiving MIDI messages.

OMNI MODE [OMNI OFF, OMNI ON] If omni mode is turned on, MIDI data will be received on all channels, regardless of the MIDI channel setting.

DEVICE ID [132] Determines the device ID used for transmitting and receiving exclusive messages.

PROGRAM CHANGE OUT This selects whether or not to output program change messages when patch numbers are changed on the GT-3. OFF:

Program change messages are not output even when patch numbers are changed.

ON:

When a patch number is changed, the program change message is output.

PC MAP SELECT (program change map select)

Determines how patch numbers will change when the VG-88 receives program change messages. FIX:

The patch numbers of the default settings will be selected.

PROG:

The patch numbers specified by the Program Change Map will be selected.

EXP PEDAL NUMBER [OFF, CC#1CC#31, CC#64CC#95]

This sets the controller number of the control change messages that will be used to transmit information describing the operation of the Expression pedal. When set to OFF, no control change messages will be transmitted.

CTL PEDAL NUMBER [OFF, CC#1CC#31, CC#64CC#95]

This sets the controller number of the control change messages that will be used to transmit information describing the operation of the CTL pedal. When set to OFF, no control change messages will be transmitted.

SUB CTL 1 NUMBER [OFF, CC#1CC#31, CC#64CC#95]

This sets the controller number of the control change messages that will be used to transmit information describing the operation of the external device connected to the SUB CTL 1 jack. When set to OFF, no control change messages will be transmitted.

SUB CTL 2 NUMBER [OFF, CC#1CC#31, CC#64CC#95]

This sets the controller number of the control change messages that will be used to transmit information describing the operation of the external device connected to the SUB CTL 2 jack. When set to OFF, no control change messages will be transmitted.

PROG MAP (program map) When using program change messages transmitted from an external MIDI device to select patch numbers, you can freely specify the correspondence between the program change messages received by the VG-88 and the patch numbers that will be selected.

BULK DUMP Provides for the transmission of data via MIDI.

START [SYSTEM, #1-1#25-4] Selects the first patch or system that will be transmitted.

END Selects the last patch or system that will be transmitted.

DUMP Initiates a bulk dump.

BULK LOAD Provides for the reception of data via MIDI.

Exchange the order of patches.

PATCH A [#1-1#25-4] PATCH B [#1-1#25-4] Select the patches that you wish to exchange.

EXCHANGE Begins the exchange.

MIDI

EXCHANGE

61

Chapter 6. Changing the system settings

GK pickup settings

Select the save destination of GK pickup settings

1. Make sure youre in Play page.

If youre not in Play page, press [EXIT] several times.

2. Press [F6] (SYSTEM).

3. Press [F1] (DRIVER).

4. Press [F1] (SETTING). fig.1-10

5. Rotate [VALUE] to select the save destination (AE).

6. Press [EXIT] several times to return to the Play page.

Adjusting the GK pickup sensitivity for each string

Adjust the pickup sensitivity for each string as appropriate for the way in which the divided pickup was installed.

* If you will be using two or more guitars to play the VG-88,

you must make sensitivity settings for the divided pickup of

each guitar. For each guitar, turn off the power of the VG-88,

re-connect, and then perform the following procedure. You can

make and store settings for up to five guitars.

* These settings are required when you newly install a divided

pickup on a guitar, or after you adjust the height of the divided

pickup. Once the settings have been made correctly, they will

be retained even while the power is turned off. So, you dont

need to redo the settings each time you play.

1. Make sure youre in Play page.

If youre not in Play page, press [EXIT] several times.

2. Press [F6] (SYSTEM).

3. Press [F1] (DRIVER).

4. Press [F1] (SETTING). Select the SETTING item that you

wish to set.

5. Rotate [VALUE] to select the save destination for the

settings.

6. Press [F2] (TYPE).

fig.1-10a

7. Rotate [VALUE] to select the pickup type for which you

are making settings.

GK-2A: Select this if you are using a GK-2A/GK-3 divided pickup.

GK-2: Select this if you are using a GK-2 divided pickup.

PIEZO: Select this if you are using a piezo divided pickup.

8. Press [PAGE ] to access page 3. fig.6-03

9. Press [F1] [F6] to select the string.

10.Rotate [VALUE] to set the value.

11.Repeat steps 9 10 to make settings for each string.

12.Press [EXIT] several times to return to the Play page.

Name the GK pickup settings 1. Make sure youre in Play page.

If youre not in Play page, press [EXIT] several times.

2. Press [F6] (SYSTEM).

3. Press [F1] (DRIVER).

4. Press [F1] (SETTING). Select the SETTING item that you

wish to set.

5. Use [CURSOR ] to move the cursor to the name of the

settings. fig.6-03a

6. Use [F1] [F6] and [VALUE] to assign a name.

[F1] ( ) : Return the cursor to the left.

[F2] ( ) : Advance the cursor to the right.

[F3] ( ) : Advance the cursor to the end.

62

Chapter 6. Changing the system settings

C h a p ter 6

[F4] (SPACE): A space will be inserted at the cursor location, and the cursor will move one space to the right.

[F5] (DELETE):

Delete a character and move the subsequent text forward.

[F6] (A, a, 1, ):

Switch between inputting uppercase characters, lowercase characters, numerals, and symbols.

* Press [CURSOR ] several times to return to the previous

page.

7. Press [EXIT] several times to return to the Play page.

Specify the direction in which the divided pickup is installed

1. Make sure youre in Play page.

If youre not in Play page, press [EXIT] several times.

2. Press [F6] (SYSTEM).

3. Press [F1] (DRIVER).

4. Press [F3] (DIRECTION). fig.1-10b

5. Rotate [VALUE] to select the direction in which the

divided pickup is installed.

NORMAL: In this direction, the cable exits on the side of string 6.

REVERSE: In this direction, the cable exits on the side of string 1.

6. Press [EXIT] several times to return to the Play page.

Specify the neck scale Specify the neck scale of the guitar you are using.

1. Make sure youre in Play page.

If youre not in Play page, press [EXIT] several times.

2. Press [F6] (SYSTEM).

3. Press [F1] (DRIVER).

4. Press [F4] (SCALE). fig.1-10d

5. Rotate [VALUE] to select the appropriate neck scale.

620 660 mm

ST: 648 mm

LP: 628 mm

6. Press [EXIT] several times to return to the Play page.

Specify the pickup phase 1. Make sure youre in Play page.

If youre not in Play page, press [EXIT] several times.

2. Press [F6] (SYSTEM).

3. Press [F1] (DRIVER).

4. Press [F5] (GT PU PHASE). fig.1-10g

5. Rotate [VALUE] to select the appropriate pickup phase.

While playing String 6, select the position that does not cause the volume of the low-frequency range to diminish significantly.

NORMAL: The phase will remain unchanged.

INVERSE: The phase will be inverted.

6. Press [EXIT] several times to return to the Play page.

Specify the distance between the divided pickup and the bridge

1. Make sure youre in Play page.

If youre not in Play page, press [EXIT] several times.

2. Press [F6] (SYSTEM).

3. Press [F1] (DRIVER).

4. Press [PAGE ] to access page 2. fig.1-10e

5. Press [F1] [F6] to select a string.

6. Rotate [VALUE] to set the value.

7. Repeat steps 5 6 to make settings for each string.

8. Press [EXIT] several times to return to the Play page.

* When TYPE is set to PIEZO, this setting is ignored.

63

Chapter 6. Changing the system settings

Exchanging the location of S1/ S2

On guitars that have a built-in divided pickup, the S1/S2 switches may be located in the opposite locations from the GK pickup. You can make this setting if you want the operation to be the same.

1. Make sure youre in Play page.

If youre not in Play page, press [EXIT] several times.

2. Press [F6] (SYSTEM).

3. Press [F1] (DRIVER).

4. Press [F6] (S1/S2 POSITION). fig.1-10f

5. Turn [VALUE] to select the setting.

NORMAL: The switch functions will be left as they are.

REVERSE: The S1 switch and S2 switch will be exchanged.

6. Press [EXIT] several times to return to the Play page.

Pedal function settings

Setting the function of the BANK pedals

1. Make sure youre in Play page.

If youre not in Play page, press [EXIT] several times.

2. Press [F6] (SYSTEM).

3. Press [F2] (PEDAL).

4. Press [F1] (BANK SW MODE). fig.6-15

5. Rotate [VALUE] to select the function of the BANK

pedal.

WAIT NUM: After changing the bank, press a number pedal [1][4] to switch the patch.

NUMBER 1: When you change the bank, patch number 1 of the newly-selected bank will be chosen.

SAME NUM: When you change the bank, the same- numbered patch as in the previously-selected bank will be chosen.

6. Press [EXIT] several times to return to the Play page.

Setting the range of bank change

This function is convenient when you wish to limit the banks that you use (for example, in a live performance situation).

1. Make sure youre in Play page.

If youre not in Play page, press [EXIT] several times.

2. Press [F6] (SYSTEM).

3. Press [F2] (PEDAL).

4. Press [F2] (BANK AREA(MIN)), and use [VALUE] to

specify the lowest bank that you wish to select. fig.6-17

5. Press [F3] (BANK AREA(MAX)), and use [VALUE] to

specify the highest bank that you wish to select.

6. Press [EXIT] several times to return to the Play page.

64

Chapter 6. Changing the system settings

C h a p ter 6

Setting the function of an external foot switch (FS-5U)

Heres how you can specify the function of an external foot switch connected to the SUB CTL 1,2 jack.

1. Make sure youre in Play page.

If youre not in Play page, press [EXIT] several times.

2. Press [F6] (SYSTEM).

3. Press [F2] (PEDAL).

4. Press [F4] (SUB CTL1), and use [VALUE] to select the

function of the SUB CTL 1 jack. fig.6-19

ASSIGNABLE: The function can be assigned by each patch as a parameter control pedal.

TUNER: The tuner screen will be displayed.

BPM(TAP): Tap input of the MASTER BPM parameter.

PU to FRONT: Switch PICKUP sequentially toward the front pickup.

PU to REAR: Switch PICKUP sequentially toward the rear pickup.

* When set to anything other than ASSIGNABLE, the

PEDAL/ASSIGN SUB CTL1 and SUB CTL2 settings are

disabled.

5. Press [F5] (SUB CTL2), and use [VALUE] to select the

function of the SUB CTL 2.

6. Press [EXIT] several times to return to the Play page.

Reflecting the New EXP Pedal and GK VOL Values When Patches Are Switched

This setting determines whether or not the current EXP Pedal and GK VOL values after switching Patches are to be shown.

1. Make sure youre in Play page.

If youre not in Play page, press [EXIT] several times.

2. Press [F6] (SYSTEM).

3. Press [F2] (PEDAL).

4. Press [F6] (EXP/GK VOL HOLD), and use [VALUE] to

turn the pedal function on/off.

fig.6-19a

ON: The values of the various controllers will be applied when a patch is recalled. If you set the CTL pedal operation to Latch and change patches when CTL is lit, the settings at the time the patch was written will be recalled.

OFF: The patch will be recalled with the settings of when it was written. (The values of the various controllers will be ignored.)

5. Press [EXIT] several times to return to the Play page.

Adjusting the depth of the built-in EXP pedal and the amount of change

You can specify the positions (minimum value/maximum value) of the built-in EXP pedal.

1. Make sure youre in Play page.

If youre not in Play page, press [EXIT] several times.

2. Press [F6] (SYSTEM).

3. Press [F2] (PEDAL).

4. Press [PAGE ] to access page 2. fig.6-22

5. Return the built-in EXP pedal, and press [F4] (SET).

The display will indicate ARE YOU SURE? fig.6-23

6. If you wish to set, press [WRITE].

* If you do not wish to set the settings, press [EXIT] to return to

Play page.

7. Advance the built-in EXP pedal, and press [F6] (SET).

The display will indicate ARE YOU SURE?

8. If you wish to set, press [WRITE].

* If you do not wish to set the settings, press [EXIT] to return to

Play page.

9. Press [EXIT] several times to return to the Play page.

65

Chapter 6. Changing the system settings

VALUE dial settings

Preventing accidental operation of the VALUE dial 1. Make sure youre in Play page.

If youre not in Play page, press [EXIT] several times.

2. Press [F6] (SYSTEM).

3. Press [F3] (DIAL). fig.6-24

4. Rotate [VALUE] to select the function of the dial.

P.NUMBER&VALUE: In the Play page, the dial will change patches. In Edit screens, it will function as a value dial.

VALUE ONLY: It will function only as a value dial in Edit screens.

5. Press [EXIT] several times to return to the Play page.

Screen/display-related settings

Adjusting the display contrast Immediately after the VG-88s power is turned on, or after it has been used for an extended period of time, the text or icons in the LCD screen may become difficult to read. If this occurs, please adjust the contrast. Heres how to adjust the contrast of the LCD screen.

1. Make sure youre in Play page.

If youre not in Play page, press [EXIT] several times.

2. Press [F3] (CONTRAST). fig.6-26

3. Rotate [VALUE] to adjust the contrast.

4. When you have finished making adjustments, press

[EXIT]. You will return to Play page.

GK pickup function settings

Selecting the function of the S1/S2 switches

1. Make sure youre in Play page.

If youre not in Play page, press [EXIT] several times.

2. Press [F4] (GK FUNC).

3. Press [F4] (DOWN/S1,UP/S2). fig.6-30

4. Rotate [VALUE] to select the function of the S1/S2

switches.

ASSIGNABLE: Settings can be made in each patch as parameter control buttons.

MASTER LEVEL: Increment or decrement the MASTER LEVEL.

PEDAL FUNCTION: While holding down the S1/S2 switch, press a VG-88 pedal to assign the function. Number pedal [1]: MASTER LEVEL down Number pedal [2]: MASTER LEVEL up Number pedal [3]: TUNER Number pedal [4]: BPM TAP VG-88 CTL pedal: Control pedal VG-88 EXP pedal: FOOT VOLUME BANK pedal: PU SELECT down BANK pedal: PU SELECT up

PATCH SELECT: Increment or decrement the patch. PU SELECT: Alters the position of the pickup used in the COSM GUITAR block. TUNER/BPM: The S1 switch will be assigned the Tuner function, and the S2 switch will be assigned the BPM (tap input) function.

5. Press [EXIT] several times to return to the Play page.

66

Chapter 6. Changing the system settings

C h a p ter 6

Selecting the function of the SYNTH VOL knob 1. Make sure youre in Play page.

If youre not in Play page, press [EXIT] several times.

2. Press [F4] (GK FUNC).

3. Press [F6] (SYNTH VOL). fig.6-32

4. Rotate [VALUE] to select the function of the SYNTH

VOL (GK Volume) knob.

ASSIGNABLE: The function can be set for each patch as a parameter control knob. Depending on the parameter that is assigned, the GK-2A/GK-3 select switch may not function. PICKUP LEVEL: Alters the position of the pickup used in the COSM GUITAR block.

MIXER LEVEL: Controls the mixer level of the COSM GUITAR.

* When set to anything other than ASSIGNABLE, the

PEDAL/ASSIGN SYNTH VOL settings are disabled.

MASTER LEVEL: Controls the MASTER LEVEL.

5. Press [EXIT] several times to return to the Play page.

If the function of the SYNTH VOL knob is set to anything other than PICKUP LEVEL or MASTER LEVEL, the select switch of the GK-2A/GK-3 cannot be used.

Rearranging the order of patches * It is not possible to rearrange the preset patches.

1. Make sure youre in Play page.

If youre not in Play page, press [EXIT] several times.

2. Press [F6] (SYSTEM).

3. Press [F6] (EXCHANGE). fig.3-03

4. Use [F1] to move the cursor to PATCH A.

5. Rotate [VALUE] to select one of the patches you wish to

exchange.

6. Use [F4] to move the cursor to PATCH B.

7. Rotate [VALUE] to select the other patch you wish to

exchange.

8. After specifying the two patches, press [F1]

(EXCHANGE). The patches will be exchanged.

9. Press [EXIT] several times to return to the Play page.

67

Chapter 7. Using MIDI

About MIDI * The Bank Select described in this chapter is different than

the Banks explained in Chapter 1. Bank Select is a type of

MIDI message that is normally used for switching Patches. A

Bank Select message has a value of 0 to 127, and is used in

combination with a Program Change message.

MIDI is a standard that is shared by a wide range of instruments from different manufacturers. For instance, you could use a MIDI controller from company A to play a sound module from company B, or to send data to a sequencer from company C.

What follows is a list of some of the different types of MIDI messages. Note On messages provide information on what note was

played, and its velocity. Note Off messages provide information on when a note

stops sounding. Pitch Bend messages provide information for changing

the pitch smoothly. Program Change messages transmit commands for

switching Patches. Control Change messages provide information on

changes in volume, tone, and other effects. System Exclusive (SysEx) messages provide information

that is unique to the instrument that originally generated them.

Checking Compatible MIDI Messages (the MIDI Implementation Chart)

MIDI makes it possible for a wide range of different instruments to communicate with each other. However, not all instruments can send and receive every type of MIDI message. Instruments can share only those types of MIDI messages that they have in common.

The owners manual for every MIDI instrument comes with a MIDI Implementation Chart, which provides a quick way to check what kinds of MIDI messages the instrument supports. You can easily determine what MIDI messages two instruments have in commonby comparing their MIDI

Implementation Charts. Just line up the charts for the sending instrument and the receiving instrument. fig.7-01

MIDI channels MIDI is able to independently control more than one MIDI device over a single MIDI cable. This is possible because of the concept of MIDI channels.

The idea of MIDI channels is somewhat similar to the idea of television channels. By changing channels on a television set, you can view a variety of programs. This is because the information of a particular channel is received when the channels of the transmitter and receiver match. fig.7-01a

MIDI has sixteen channels 1 16, and MIDI messages will be received by the instrument (the receiving device) whose channel matches the channel of the transmitter.

* If omni mode is on, data of all MIDI channels will be received

regardless of the MIDI channel setting. If you do not need to

control a specific MIDI channel, you may set Omni On.

What is MIDI? MIDI stands for Musical Instrument Digital Interface, a worldwide standard that enables electronic instruments and peripherals to share information about performances, sound switching, and other functions.

TransmitFunction

Fold here MIDI Device A MIDI Device B

Recognized Remarks

A separate publication titled MIDI Implementation is also available. It provides complete details concerning the way MIDI has been implemented on this unit. If you should require this publication (such as when you intend to carry out byte-level programming), please contact the nearest Roland Service Center or authorized Roland distributor.

Broadcasting Station A

T.V. information from many different broadcasting station is sent through an antena.

Select the channel of the broadcasting station you wish to watch

Broadcasting Station B

Broadcasting Station C

68

Chapter 7. Using MIDI

C h a p ter 7

1. Make sure youre in Play page.

If youre not in Play page, press [EXIT] several times.

2. Press [F6] (SYSTEM).

3. Press [F5] (MIDI).

4. Press [F1] (CHANNEL). fig.7-02

5. Rotate [VALUE] to select the MIDI channel (1 16).

6. Press [EXIT] several times to return to the Play page.

* This setting is preserved even after you turn off the power.

About MIDI Omni Mode * Even if Omni Mode is turned ON, exclusive data will be

received only if its device ID matches the Device ID setting

of the VG-88.

* The factory setting is OMNI ON.

1. Make sure youre in Play page.

If youre not in Play page, press [EXIT] several times.

2. Press [F6] (SYSTEM).

3. Press [F5] (MIDI).

4. Press [F2] (OMNI MODE). fig.7-03

5. Rotate [VALUE] to turn the setting on/off.

OMNI ON:

Data of all MIDI channels will be received, regardless of the MIDI channel setting.

OMNI OFF:

Data of only the specified MIDI channel will be received.

6. Press [EXIT] several times to return to the Play page.

* This setting is preserved even after you turn off the power.

About the MIDI Device ID Heres how to specify the device ID that is used when transmitting and receiving exclusive data.

* The factory setting is 1.

1. Make sure youre in Play page.

If youre not in Play page, press [EXIT] several times.

2. Press [F6] (SYSTEM).

3. Press [F5] (MIDI).

4. Press [F3] (DEVICE ID). fig.7-04

5. Rotate [VALUE] to set the device ID (1 32).

6. Press [EXIT] several times to return to the Play page.

* This setting is preserved even after you turn off the power.

Bank Select and Program Change

Bank Select and Program Change are MIDI messages that are generally used to switch Patches.

Ordinarily, Program Change messages are used in Patch switching. However, Program Change messages can only select a maximum of 128 patches. Thats why some instruments use the Bank Select MSB together with Program Change messages to expand the number of selectable Patches to 16,384 (128 x 128).

On instruments like these, each Patch is assigned a number that is a combination of a Bank Number MSB from 0 to 127 and a Program Number from 1 to 128.

69

Chapter 7. Using MIDI

Switching the patches of an external device You can select whether or not Program Changes will be transmitted when you change patches.

* The Program Changes transmitted for patches are fixed. You

may want to alter Program Change reception map settings on

the external device when necessary.

1. Make sure youre in Play page.

If youre not in Play page, press [EXIT] several times.

2. Press [F6] (SYSTEM).

3. Press [F5] (MIDI).

4. Press [F4] (PROGRAM CHANGE OUT). fig.7-06

5. Rotate [VALUE] to switch transmission ON or OFF.

6. Press [EXIT] several times to return to the Play page.

* This setting is preserved even after you turn off the power.

Selecting the Program Change map

By transmitting bank select and Program Change messages from an external MIDI device to the VG-88, you can switch VG-88 patches without using its foot pedals or [VALUE] dial.

1. Make sure youre in Play page.

If youre not in Play page, press [EXIT] several times.

2. Press [F6] (SYSTEM).

3. Press [F5] (MIDI).

4. Press [F6] (PROG MAP).

5. Press [F5] (PC MAP SELECT). fig.7-07

6. Rotate [VALUE] to change the setting.

FIX:

The default patch number will be selected. PROG:

The patch number you specified in the Program Change map will be selected.

7. Press [EXIT] several times to return to the Play page.

* This setting is preserved even after you turn off the power.

70

Chapter 7. Using MIDI

C h a p ter 7

Setting the Program Change reception map

1. Make sure youre in Play page.

If youre not in Play page, press [EXIT] several times.

2. Press [F6] (SYSTEM).

3. Press [F5] (MIDI).

4. Press [PAGE ] to access page 3. fig.7-08a

5. Press [CURSOR] to move the cursor to the BANK PROG

value, then turn [VALUE] to move to the Program Change number to be set.

fig.7-08a

6. Press [CURSOR] to move the cursor to the PATCH value,

then select the target VG-88 internal Patch. fig.7-08b

7. Repeat steps 56 as necessary.

8. Press [EXIT] several times to return to the Play page.

* This setting is preserved even after you turn off the power.

Synchronizing to the MIDI CLOCK arriving at MIDI IN

1. Make sure you're at the Play screen.

If the Play screen is not the current screen, press [EXIT] a number of times until the Play screen appears.

2. Press [F2] (BPM TAP). fig.7-08c

3. Turn [VALUE] to set the value to MIDI.

4. Once youve finished making the setting, you may want

to save it. To do so, carry out the Write procedure (p. 25).

* If you do not want to save the setting, press [EXIT] to return

to the Play screen.

Specifying the Control Change number transmitted when the pedal is operated Here's how to specify the Control Change number that will be transmitted when you operate the built-in pedal or an external pedal.

1. Make sure youre in Play page.

If youre not in Play page, press [EXIT] several times.

2. Press [F6] (SYSTEM).

3. Press [F5] (MIDI).

4. Press [PAGE ] to access page 2. fig.7-09

5. Use [CURSOR] to move the cursor to the parameter that

you wish to set.

6. Turn [VALUE] to specify the Control Change number

that will be transmitted.

7. Repeat steps 56 as necessary.

8. Press [EXIT] several times to return to the Play page.

* This setting is preserved even after you turn off the power.

71

Chapter 7. Using MIDI

Transmitting/receiving all sound data The VG-88s system parameter and patch parameter settings can be transferred as a whole to or from an external device as MIDI exclusive data.

If you use a MIDI sequencer that is able to record exclusive data, you can transmit system parameters and patch parameters to the MIDI sequencer, and save them on a floppy disk. Alternatively, you can directly connect two VG-88 units via a MIDI cable, and transmit or receive parameters directly.

Transmitting settings to an external device (BULK DUMP)

1. Make sure youre in Play page.

If youre not in Play page, press [EXIT] several times.

2. Press [F6] (SYSTEM).

3. Press [F5] (MIDI).

4. Press [PAGE ] to access the BULK DUMP screen. fig.7-11

5. Press [F1] (START), and use [VALUE] to select the first

patch or system that you wish to transmit.

6. Press [F4] (END), and use [VALUE] to select the last

patch or system that you wish to transmit.

7. Press [F6] (DUMP). Transmission will begin. fig.7-12

8. Press [EXIT] several times to return to the Play page.

Receiving settings from an external device (BULK LOAD)

You must use the following procedure to receive bulk dump data from an external device.

1. Make sure youre in Play page.

If youre not in Play page, press [EXIT] several times.

2. Press [F6] (SYSTEM).

3. Press [F5] (MIDI).

4. Press [PAGE ] to access the BULK LOAD screen. fig.7-13

5. Transmit the bulk data from the external MIDI device.

* If the display indicates MIDI Receive Error !!, check the

connections and slow down the tempo of the transmitting

MIDI device.

6. When data reception is complete, the following display

will appear. fig.7-14

At this time, data may continue to be received.

7. Press [EXIT] to end the BULK LOAD.

The following display will appear. fig.7-14a

8. Press [EXIT] several times to return to the Play page.

72

Chapter 8. Appendices

C h a p ter 8

Troubleshooting This section explains some things that might go wrong when using the VG-88, and what needs to be done to correct the problem. If you think there may be something wrong with your VG-88, please check through the following first. If these suggestions dont fix the problem, then go ahead and contact the store you bought it from, or your nearest Roland Service Station.

Trouble with the Sound The sound isnt right.

Is the divided pickup setting correctly?

Check the divided pickup setting (p. 14, 18).

There is no VG sound when the guitar is played.

Are the audio cables and the GK pickup connected

correctly?

Make sure the connections are correct (p. 14, 15).

Are the VG-88, guitar amp, mixer, and other equipment

switched on?

Make sure the power is turned on for all equipment.

Is [VOLUME] on the VG-88 set to MIN?

Raise the volume to an appropriate level (probably somewhere near the midway point).

Is the selector switch on the GK pickup set to

GUITAR?

Set the selector switch to MIX.

Has the volume function been assigned to the

expression pedal and others?

If the volume function has been assigned to the expression pedal and others, and the pedal is in the fully returned position (toward yourself), there will be no sound. Advance the pedal away from yourself.

The GK pickups select switch does not switch the signal

Is the SYNTH VOL knob set to a setting other than

MASTER LEVEL or PICKUP LEVEL?

Set it to MASTER LEVEL, PICKUP LEVEL, or MIXER LEVEL (p. 67).

The pitch isnt right. Is the guitar in tune?

Tune the guitar (p. 17).

Is the VG-88 out of tune with other instruments?

Adjust the Standard pitch setting (p. 17).

Has COSM GUITAR Pitch Shift been set?

Set an appropriate value for COSM GUITAR Pitch Shift (p. 39).

The volume fluctuates from one string to another.

Are the Sensitivity settings for all strings correct?

Adjust the settings if necessary (p. 20).

Onboard effects are not applied Is the effect turned OFF?

If an effect is turned OFF, that effect will not be applied. Turn the effect ON.

Are the effect levels high enough?

An effect is not applied and only the original sound is heard when the effect level is at the lowest setting. Set the effect level to an appropriate value.

Depending on the guitar being used, hum may be audible.

Is the output jack on your guitar connected to the

NORMAL GUITAR input jack on the GK-2A/GK-3?

You should be sure to make this connection even if the guitar sound is not to be output. For more details, see the Owners Manual for the GK-2A/GK-3.

The volume level of the instrument connected to GK IN or GUITAR INPUT is too low.

Could you be using a connection cable that contains a

resistor?

Use a connection cable that does not contain a resistor.

Other Problems BATTERY LOW is displayed when the power is switched on.

The internal battery for saving Patch and system parameters is almost out of power. Replace the battery soon to prevent parameters from being lost. Contact your nearest Roland Service Station or the store where you bought the VG-88.

Patches arent switched when a Program Change is received from an external device.

Are the Program Change messages being received on a

MIDI channel other than the channel set for MIDI

Channel on the System MIDI screen?

Send the Program Change messages on the same channel as the one set with MIDI Channel.

Is an invalid Bank Select being transmitted? Make settings so that a Bank Number MSB that the VG- 88 can use is transmitted.

73

Chapter 8. Appendices

Cant transmit/receive data via bulk dump Are you performing the operation in the bulk dump

transmit/receive screens?

Move to the bulk dump transmit/receive screens.

Is the MIDI sequencer you are using able to record

exclusive data?

Use a MIDI sequencer that is able to record exclusive data. We recommend that you use the Roland MC-80.

When receiving, is the device ID number set to the

same value used when sending?

Set the device ID number to the same number that was used when the data was sent.

Restoring the factory settings (Initialization) To restore the factory settings of the VG-88, do as follows. You can initialize all settings, or only a specified section of the patch data in the user area or system settings. The following types of data can be initialized.

Display Data that is initialized

SYSTEM All system parameters #1-1 #25-4 The setting contents of patches 1-1 25-4 fig.8-03

1. Turn off the power.

2. While holding [PAGE ] and [PAGE ] down, switch

on the unit. A display will appear, allowing you to specify the area of data you wish to initialize.

fig.8-01

3. Move the cursor to START with [CURSOR], then use

the VALUE dial to get the display to show the data that is the beginning point of the initialization.

4. Move the cursor to END with [CURSOR], then get the

display to show the ending point of the initialization, also using the VALUE dial.

5. Press [WRITE].

The display will indicate ARE YOU SURE?

6. If you wish to initialize, press [WRITE].

The specified area of data will be initialized. The VG-88 will then be in its normal power-on state.

* If you decide not to initialize the settings, press [EXIT].

Initialization will be canceled, and the normal power-on

display will appear.

3,4

3,4

12

74

Chapter 8. Appendices

C h a p ter 8

MIDI Implementation Chart fig.8-01

Function...

Basic Channel

Mode

Note Number :

Velocity

After Touch

Pitch Bend

Control Change

Prog Change

System Exclusive

System Common

System Real Time

Aux Message

Notes

Transmitted Recognized Remarks

Default Changed

Default Messages Altered

True Voice

Note ON Note OFF

Key's Ch's

0, 32 131

6495

: True #

: Song Pos : Song Sel : Tune

: Clock : Command

: All sound off : Local ON/OFF : All Notes OFF : Active Sense : Reset

116 116

X X

X X

X **************

X X

X

O O O

*1 *3 *3

O O O

*2 *4 *4

O 099

*1

O

X X X

X X

X X X X X

116 116

OMNI ON/OFF X

X X

X

X X

X

O 0127

O

X X X

O X

*7

X X X X X

Bank Select

* 1 You can make a setting that either allows or prohibits transmission. * 2 This ignores the LSB. * 3 This message is assigned to the VG-88s pedal as well as the external pedal. * 4 This recognize the message set for Parameters realtime control. * 5 Bulk data is transmitted only when the MIDI Bulk Dump screen is displayed. * 6 Bulk data is received only when the MIDI Bulk Load screen is displayed. * 7 Recognized when the BPM Patch parameter is set to MIDI.

Model VG-88

Date : Mar. 1, 2000

Version : 1.01MIDI Implementation Chart

**************

Mode 1 : OMNI ON, POLY

Mode 3 : OMNI OFF, POLY

Mode 2 : OMNI ON, MONO

Mode 4 : OMNI OFF, MONO

O : Yes

X : No

Program Number 1128

Memorized

V-GUITAR SYSTEM

Memorized

*5 *6

75

Chapter 8. Appendices

Specifications VG-88: V-Guitar System

AD Conversion A/D 24 bit AF Method (NORMAL INPUT) 20 bit (GK INPUT)

D/A Conversion 20 bit 128 times Oversampling Modulation

Sampling Frequency 44.1 kHz

Program Memories 260 (Preset: 160 + User: 100)

Nominal Input Level INPUT: -10 dBu

Input Impedance INPUT: 1 M

Nominal Output Level OUTPUT: +4 dBu GUITAR OUT: -10 dBu

Output Impedance OUTPUT: 2 k GUITAR OUT: 2 k

Dynamic Range 100 dB or greater (IHF-A)

Display 160 x 64 dots backlit LCD 8-segment 2-character LED

Control Output Level knob Value dial Cursor buttons Output Select button Function buttons 16

Page button

Page button Exit button Write button COSM Guitar button COSM Amp button Effects button Level/BPM/Key button Pedal/Assign button Name/Chain button EZ Edit button Tuner button Number pedals 14 CTL pedal Bank Up pedal Bank Down pedal

Expression pedal Pedal Number LEDs 14 Control Pedal LED Output Select LEDs x 3 Power switch

Connectors GK IN GUITAR INPUT GUITAR OUTPUT OUTPUT L (MONO) OUTPUT R PHONES SUB EXP PEDAL/SUB CTL1, 2 MIDI IN MIDI OUT

Power Supply AC 117 V, 230 V, 240 V

Power Consumption 24 W

Dimensions 504 (W) x 303 (D) x 101 (H) mm 19-7/8 (W) x 11/15/16 (D) x 4 (H) inches

Weight 4.9 kg / 10 lbs 13 oz

Accessories Power Cord Owners Manual Quick Start GK Connecting Cable: C13-A (5 m)

Options Divided Pickup: GK-2A, GK-3 Unit Selector: US-20 GK Parallel Box: GKP-4 GK Cable: GKC-3 (3 m), GKC-5 (5 m), GKC-10 (10 m) Expression Pedal: EV-5, FV-300L Foot Switch: FS-5U, FS-5L, FS-6

(0 dBu=0.775 Vrms)

In the interest of product improvement, the specifications and/or appearance of this unit are subject to change without prior notice.

76

Index

Numerics 12STRINGS ..................................................................... 36 2x2 CHORUS ................................................................. 52

A ACOUSTIC ..................................................................... 36 ACTIVE RANGE ..................................................... 32, 56 ATTACK ......................................................................... 44

B BANK AREA .................................................................. 64 BANK SW MODE ......................................................... 64 BODY .............................................................................. 39 BODY LEV ...................................................................... 44 BOWED .......................................................................... 36 BPM ................................................................................. 55 BRASS ............................................................................. 37 BULK DUMP ................................................................. 72 BULK LOAD .................................................................. 72

C CHANNEL ..................................................................... 69 CHORUS ........................................................................ 53 COLOR ........................................................................... 43 COMP/LM ..................................................................... 47 CONTRAST .............................................................. 56, 66 Control Change number .............................................. 71 COSM AMP ............................................................. 28, 46 COSM GUITAR ....................................................... 27, 36 CRYSTAL ....................................................................... 37

D DELAY ............................................................................ 53 DETUNE ......................................................................... 41 DEVICE ID ..................................................................... 69 DIAL ................................................................................ 60 DIRECTION ................................................................... 63 divided pickup ........................................................ 14, 18 DOWN/S1 ................................................................ 57, 66 DRIVER ..................................................................... 6263 driver settings ................................................................ 18 DUAL .............................................................................. 36

E EFFECTS ................................................................... 28, 47 EQ .............................................................................. 45, 48 EXCHANGE ...................................................... 25, 61, 67 EXP/GK VOL HOLD ................................................... 65 EZ EDIT .......................................................................... 56 EZ Edit ............................................................................ 26

F FILTER ............................................................................ 43 FILTER-BASS ................................................................. 37 FLANGER ...................................................................... 50 FV ..................................................................................... 54

G GK FUNC ........................................................... 57, 6667 GK-3 ................................................................................ 14

GLIDE ............................................................................. 43 GLOBAL ................................................................... 35, 58 GT PU PHASE ............................................................... 63

H HARMONIST ................................................................. 49

I initialization ................................................................... 74

K KEY .................................................................................. 55

L LEVEL ............................................................................. 55 LEVEL/BPM/KEY .................................................. 35, 55

M MIDI .................................................................... 61, 6872 MIDI CLOCK ................................................................. 71 MIDI Implementation Chart ........................................ 75 MIDI SYNC .................................................................... 29 MIXER ............................................................................. 45 MOD ................................................................................ 49

N name ................................................................................ 34 NAME/CHAIN ....................................................... 32, 34 NS .................................................................................... 54 NYLON STRINGS ......................................................... 36

O OMNI MODE ................................................................. 69 OPEN TUNE .................................................................. 36 ORGAN .................................................................... 37, 44 OUTPUT SELECT ................................................... 21, 58

P P.SHIFTER ...................................................................... 50 Page icon ......................................................................... 16 PAN ........................................................................... 45, 52 Patch ................................................................................ 22 P-BEND ........................................................................... 43 PC MAP SELECT .......................................................... 70 PD SHIFT ............................................................ 36, 41, 52 PEDAL ............................................................................ 60 PEDAL/ASSIGN ............................................... 2931, 55 PHASER .......................................................................... 51 PICKUP ........................................................................... 37 PIPE ................................................................................. 37 Play page ........................................................................ 17 POLY COMP .................................................................. 36 POLY COMP/LIMITER ............................................... 42 POLY DIST ..................................................................... 36 POLY DISTORTION ..................................................... 41 POLY OCT ...................................................................... 36 POLY OCTAVE ............................................................. 42 POLY SG ................................................................... 36, 42 PROGRAM CHANGE OUT ........................................ 70 PT SHIFT ........................................................................ 39

77

Index

PWM ............................................................................... 37 PWM MOD .................................................................... 44

R rearranging ..................................................................... 25 REVERB .......................................................................... 54

S S1/S2 POSITION ........................................................... 64 saving .............................................................................. 25 SCALE ............................................................................. 63 SOLO ............................................................................... 37 SUB CTL1 ....................................................................... 65 SUB EQ ........................................................................... 51 SUSTAIN ........................................................................ 43 SYNTH VOL ............................................................ 57, 67 SYSTEM .......................................................................... 59

T TREMOLO ...................................................................... 52 TUNE .............................................................................. 40 TUNER ............................................................................ 58 tuning .............................................................................. 17

U UP/S2 ........................................................................ 57, 66

V VARI GT ......................................................................... 36 VIBRATO ........................................................................ 52

W WAH ............................................................................... 47 WRITE ............................................................................. 25

78

VG-88 PATCH LIST

No. Name

USER 1-1 V-GUITAR

USER 1-2 AcGt12st

USER 1-3 TEXS ST

USER 1-4 OCT DRV

USER 2-1 SMOKE ST

USER 2-2 NYLON

USER 2-3 STD JAZZ

USER 2-4 ECHO PAD

USER 3-1 OD STACK

USER 3-2 12st+EGt

USER 3-3 MILD ST

USER 3-4 ORGAN

USER 4-1 BG DRV

USER 4-2 AcGt+BS

USER 4-3 WAH STRT

USER 4-4 HORN Gt

USER 5-1 DeepEcho

USER 5-2 LA NYLON

USER 5-3 -1OCT ST

USER 5-4 BASS DRV

USER 6-1 BluesDrv

USER 6-2 CAPO -4

USER 6-3 BODY

USER 6-4 PAN SFX

USER 7-1 ES WAH

USER 7-2 AcGt MIX

USER 7-3 TELE MOD

USER 7-4 Em9

USER 8-1 LP WAH

USER 8-2 12ST AG

USER 8-3 CLEAN TL

USER 8-4 ROTARY

USER 9-1 DropD -1

USER 9-2 NYLON St

USER 9-3 NICE DRV

USER 9-4 FAT BASS

USER 10-1 METAL ST

USER 10-2 StudioAG

USER 10-3 CrunchTL

USER 10-4 ARPEGGIO

No. Name

USER 11-1 FatMETAL

USER 11-2 Ac PIEZO

USER 11-3 f HOLE

USER 11-4 HARMO 12

USER 12-1 DropD -2

USER 12-2 DETUNE12

USER 12-3 BRT LP

USER 12-4 BOWED

USER 13-1 WAH TL

USER 13-2 ALL E

USER 13-3 JAZZ TL

USER 13-4 DRV BASS

USER 14-1 MetalWah

USER 14-2 NASH Gt

USER 14-3 BODY 12

USER 14-4 STEP SFX

USER 15-1 WAH +7

USER 15-2 BANJO

USER 15-3 PD SHIFT

USER 15-4 SlowEcho

USER 16-1 MTL SOLO

USER 16-2 CAPO 7

USER 16-3 TL TWIN

USER 16-4 OCTAVE24

USER 17-1 CoolLead

USER 17-2 MINI AMP

USER 17-3 OPEN E

USER 17-4 AnalogGR

USER 18-1 FatBlues

USER 18-2 DRVCLN

USER 18-3 STRATCru

USER 18-4 12st OCT

USER 19-1 OctMetal

USER 19-2 LIP MTL

USER 19-3 R&R

USER 19-4 BRASS+Gt

USER 20-1 LP DRIVE

USER 20-2 SMOKER

USER 20-3 BG CRUNC

USER 20-4 SLOW ATK

No. Name

USER 21-1 FAT 1959

USER 21-2 TELE DRV

USER 21-3 SPACSTRT

USER 21-4 OCT SFX

USER 22-1 '80s BG

USER 22-2 FAT BG

USER 22-3 TL+BODY

USER 22-4 SYN LEAD

USER 23-1 '70s LED

USER 23-2 TexsLead

USER 23-3 DarkJAZZ

USER 23-4 Bell Mix

USER 24-1 WAH LEAD

USER 24-2 FuzzLead

USER 24-3 CLEAN 12

USER 24-4 BASS AMP

USER 25-1 AngleWAH

USER 25-2 HARDROCK

USER 25-3 '60sECHO

USER 25-4 BAMBOO

79

No. Name

PRESET 26-1 V-GUITAR

PRESET 26-2 AcGt12st

PRESET 26-3 TEXS ST

PRESET 26-4 OCT DRV

PRESET 27-1 SMOKE ST

PRESET 27-2 NYLON

PRESET 27-3 STD JAZZ

PRESET 27-4 ECHO PAD

PRESET 28-1 OD STACK

PRESET 28-2 12st+EGt

PRESET 28-3 MILD ST

PRESET 28-4 ORGAN

PRESET 29-1 BG DRV

PRESET 29-2 AcGt+BS

PRESET 29-3 WAH STRT

PRESET 29-4 HORN Gt

PRESET 30-1 -1OCT ST

PRESET 30-2 BODY

PRESET 30-3 TELE MOD

PRESET 30-4 CLEAN TL

PRESET 31-1 JAZZ TL

PRESET 31-2 BODY 12

PRESET 31-3 PD SHIFT

PRESET 31-4 TL TWIN

PRESET 32-1 SPACSTRT

PRESET 32-2 TL+BODY

PRESET 32-3 DarkJAZZ

PRESET 32-4 CLEAN 12

PRESET 33-1 JC CLEAN

PRESET 33-2 Rick12st

PRESET 33-3 American

PRESET 33-4 '60s BOX

PRESET 34-1 335CUTIN

PRESET 34-2 COOLJAZZ

PRESET 34-3 ST WING

PRESET 34-4 ST LINE

PRESET 35-1 SlowGEAR

PRESET 35-2 EchoJAZZ

PRESET 35-3 OCT N.PU

PRESET 35-4 CLEAN ST

PRESET 36-1 CH JAZZ

PRESET 36-2 MildJazz

PRESET 36-3 R+F CUT

PRESET 36-4 TwCHORUS

PRESET 37-1 LP FRONT

PRESET 37-2 BRT HALF

PRESET 37-3 MILD TL

PRESET 37-4 TELE BRT

PRESET 38-1 CLN-LEAD

PRESET 38-2 COMP JC

PRESET 38-3 RICK CLN

PRESET 38-4 12stRICK

PRESET 39-1 NICE DRV

PRESET 39-2 CrunchTL

PRESET 39-3 f HOLE

PRESET 39-4 BRT LP

No. Name

PRESET 40-1 OPEN E

PRESET 40-2 STRATCru

PRESET 40-3 R&R

PRESET 40-4 BG CRUNC

PRESET 41-1 '60sECHO

PRESET 41-2 PHASE LP

PRESET 41-3 CRY TELE

PRESET 41-4 HALF DRV

PRESET 42-1 '60s R&R

PRESET 42-2 ST STACK

PRESET 42-3 NATURAL

PRESET 42-4 BLUES MS

PRESET 43-1 SmallAmp

PRESET 43-2 TELE TW

PRESET 43-3 WahCRUNC

PRESET 43-4 EC LEAD

PRESET 44-1 DeepEcho

PRESET 44-2 BluesDrv

PRESET 44-3 ES WAH

PRESET 44-4 LP WAH

PRESET 45-1 DropD -1

PRESET 45-2 METAL ST

PRESET 45-3 FatMETAL

PRESET 45-4 DropD -2

PRESET 46-1 WAH TL

PRESET 46-2 MetalWah

PRESET 46-3 WAH +7

PRESET 46-4 MTL SOLO

PRESET 47-1 CoolLead

PRESET 47-2 FatBlues

PRESET 47-3 OctMetal

PRESET 47-4 LP DRIVE

PRESET 48-1 FAT 1959

PRESET 48-2 '80s BG

PRESET 48-3 '70s LED

PRESET 48-4 WAH LEAD

PRESET 49-1 AngleWAH

PRESET 49-2 '70s MS

PRESET 49-3 BOOGIE

PRESET 49-4 BLUES

PRESET 50-1 MINI AMP

PRESET 50-2 DRVCLN

PRESET 50-3 LIP MTL

PRESET 50-4 SMOKER

PRESET 51-1 TELE DRV

PRESET 51-2 FAT BG

PRESET 51-3 TexsLead

PRESET 51-4 FuzzLead

PRESET 52-1 HARDROCK

PRESET 52-2 DROP D

PRESET 52-3 REVERSE

PRESET 52-4 JB LEAD

PRESET 53-1 OCT DIST

PRESET 53-2 PAF LEAD

PRESET 53-3 POLYDIST

PRESET 53-4 FUZZ BOX

No. Name

PRESET 54-1 TIGHT MT

PRESET 54-2 CH DRIVE

PRESET 54-3 BEAT DRV

PRESET 54-4 PEDAL+12

PRESET 55-1 LA NYLON

PRESET 55-2 CAPO -4

PRESET 55-3 AcGt MIX

PRESET 55-4 12ST AG

PRESET 56-1 NYLON St

PRESET 56-2 StudioAG

PRESET 56-3 Ac PIEZO

PRESET 56-4 DETUNE12

PRESET 57-1 ALL E

PRESET 57-2 NASH Gt

PRESET 57-3 BANJO

PRESET 57-4 CAPO 7

PRESET 58-1 BASS DRV

PRESET 58-2 PAN SFX

PRESET 58-3 Em9

PRESET 58-4 ROTARY

PRESET 59-1 FAT BASS

PRESET 59-2 ARPEGGIO

PRESET 59-3 HARMO 12

PRESET 59-4 BOWED

PRESET 60-1 DRV BASS

PRESET 60-2 STEP SFX

PRESET 60-3 SlowEcho

PRESET 60-4 OCTAVE24

PRESET 61-1 AnalogGR

PRESET 61-2 12st OCT

PRESET 61-3 BRASS+Gt

PRESET 61-4 SLOW ATK

PRESET 62-1 OCT SFX

PRESET 62-2 SYN LEAD

PRESET 62-3 Bell Mix

PRESET 62-4 BASS AMP

PRESET 63-1 BAMBOO

PRESET 63-2 12st 5th

PRESET 63-3 CRYSTAL

PRESET 63-4 RezoBASS

PRESET 64-1 SPACE DS

PRESET 64-2 MildHorn

PRESET 64-3 NoizLoop

PRESET 64-4 PWM LEAD

PRESET 65-1 SoftLead

PRESET 65-2 DrvSYNTH

PRESET 65-3 GONG

PRESET 65-4 VIRUS

80

PEDAL/ASSIGN Parameter List

COSM GUITAR

COSM GT (COSM GUITAR) ON/OFF

F-BASS COLOR

BODY ATTACK BODY LOW CUT LEVEL

COSM EQ (EQ) ON/OFF LEVEL L-MID G LOW G HIGH G H-MID G

PICKUP PICKUP TONE LEVEL

PT SHIFT (PITCH SHIFT) ON/OFF SHIFT16 FINE16 E.LEVEL16 D.LEVEL16 HARMO16

TUNE ON/OFF TUNE TYPE SHIFT16 ON/OFF

DETUNE DETUNE

PAN STRING-16

PD SHIFT ON/OFF PITCH STRING-16

DIST (POLY DISTROTION) ON/OFF DRIVE LEVEL POLY RATE DRV BAL

COSM COMP (POLY COMPRESSOR) ON/OFF SUSTAIN TONE LEVEL THRESHOLD

OCTAVE (POLY OCTAVE) ON/OFF -1OCT6 -2OCT16 DIR16

SG (POLY SLOW GEAR) ON/OFF

MIXER BALANCE LEVEL

FILTER CUTOFF DECAY

ATTACK LENGTH MOD-TUNE MOD-DEP LEVEL

ORGAN FEET-4 FEET-8 FEET-16

P-BEND P-BEND Q

GLIDE GLD-SENS

COSM MOD (MOD) DEPTH RATE

COSM AMP

COSM AMP ON/OFF VOLUME PRESENCE HIGH CUT MASTER BASS MIDDLE TREBLE GAIN BRIGHT

EFFECTS

FX:COMP (COMPRESSOR) ON/OFF SUSTAIN TONE LEVEL

FX:LM (LIMITER) THRESHOLD TONE LEVEL

FX:WAH (WAH) ON/OFF

FX:PD WAH (PEDAL WAH) FREQ LEVEL

FX:AT WAH (AUTO WAH) FREQ PEAK RATE DEPTH LEVEL

FX:EQ (EQ) ON/OFF LEVEL L-MID G LOW G HIGH G H-MID G

FX:MOD (MOD) ON/OFF

FX:HARMO (HARMONIST) 1:ON/OFF 1:HARMONY 1:PAN 1:LEVEL DIR LEV 2:ON/OFF 2:HAMONY 2:PAN 2:LEVEL

FX:P.SFT (P.SHIFTER) 1:ON/OFF 1:SHIFT 1:FINE

81

1:F.BACK 1:PAN 1:LEVEL DIR LEVEL 2:ON/OFF 2:SHIFT 2:FINE 2:PAN 2:LEVEL

FX:FL (FLANGER) RATE DEPTH MANUAL RESONANCE LEVEL

FX:PH (PHASER) RATE DEPTH MANUAL RESONANCE LEVEL STEP

FX:SUB EQ (SUB EQ) LEVEL L-MID G LOW G HIGH G H-MID G

FX:2x2CE (2x2CHORUS) L-RATE L-DEPTH L-LEVEL H-RATE H-DEPTH H-LEVEL

FX:TRT (REMOLO) RATE DEPTH

FX:PAN (PAN) RATE DEPTH

FX:PD SFT (PD SHIFT) PITCH

FX:VB (VIBRATO) TRIGGER RATE DEPTH

FX:DELAY (DELAY) ON/OFF DLY TIME FEEDBACK DLY LEVEL

FX:CHORUS(CHORUS) ON/OFF RATE DEPTH CE LEVEL

FX:REVERB (REVERB) ON/OFF REV TIME REV LEV

FX:NS (NOISE SUPPRESSOR) ON/OFF

FX:FV (FOOT VOLUME) LEVEL

LEVEL/BPM/KEY

MASTER (LEVEL/BPM/KEY) LEVEL BPM(TAP) KEY

TUNER

TUNER (TUNER) ON/OFF

82

This product complies with the requirements of European Directives EMC 89/336/EEC and LVD 73/23/EEC.

For EU Countries

For EU Countries

Apparatus containing Lithium batteries

ADVARSEL! Lithiumbatteri - Eksplosionsfare ved fejlagtig hndtering. Udskiftning m kun ske med batteri af samme fabrikat og type. Levr det brugte batteri tilbage til leverandren.

VARNING Explosionsfara vid felaktigt batteribyte. Anvnd samma batterityp eller en ekvivalent typ som rekommenderas av apparattillverkaren. Kassera anvnt batteri enligt fabrikantens instruktion.

CAUTION Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Discard used batteries according to the manufacturers instructions.

ADVARSEL Eksplosjonsfare ved feilaktig skifte av batteri. Benytt samme batteritype eller en tilsvarende type anbefalt av apparatfabrikanten. Brukte batterier kasseres i henhold til fabrikantens instruks joner.

VAROITUS Paristo voi rjht, jos se on virheellisesti asennettu. Vaihda paristo ainoastaan laitevalmistajan suosittelemaan tyyppiin. Hvit kytetty paristo valmistajan ohjeiden mukaisesti.

This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.

Cet appareil numrique de la classe B respecte toutes les exigences du Rglement sur le matriel brouilleur du Canada.

NOTICE

AVIS

For the USA

FEDERAL COMMUNICATIONS COMMISSION RADIO FREQUENCY INTERFERENCE STATEMENT

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.

Unauthorized changes or modification to this system can void the users authority to operate this equipment. This equipment requires shielded interface cables in order to meet FCC class B Limit.

For Canada

2

To resize thickness, move all items on the front cover to left or right

IMPORTANT SAFETY INSTRUCTIONS

CAUTION RISK OF ELECTRIC SHOCK

DO NOT OPEN

ATTENTION: RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK).

NO USER-SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated dangerous voltage within the products enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product.

INSTRUCTIONS PERTAINING TO A RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS.

IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS

WARNING - When using electric products, basic precautions should always be followed, including the following:

1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with a dry cloth. 7. Do not block any of the ventilation openings. Install in

accordance with the manufacturers instructions. 8. Do not install near any heat sources such as radiators,

heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. When the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

WARNING: IMPORTANT:

As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows:

The wire which is coloured GREEN-AND-YELLOW must be connected to the terminal in the plug which is marked by the letter E or by the safety earth symbol or coloured GREEN or GREEN-AND-YELLOW.

The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured BLACK. The wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or coloured RED.

THIS APPARATUS MUST BE EARTHED THE WIRES IN THIS MAINS LEAD ARE COLOURED IN ACCORDANCE WITH THE FOLLOWING CODE. GREEN-AND-YELLOW: EARTH, BLUE: NEUTRAL, BROWN: LIVE

For the U.K.

10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11. Only use attachments/accessories specified by the manufacturer.

12. Never use with a cart, stand, tripod, bracket, or table except as specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

13. Unplug this apparatus during lightning storms or when unused for long periods of time.

14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

Thank you, and congratulations on your choice of the Roland VG-88 V- GUITAR SYSTEM.

Before using this unit, carefully read the sections entitled: IMPORTANT SAFETY INSTRUCTIONS (Owners manual p. 2), USING THE UNIT SAFELY (Owners manual p. 3), and IMPORTANT NOTES (Owners manual p. 11). These sections provide important information concerning the proper operation of the unit. Additionally, in order to feel assured that you have gained a good grasp of every feature provided by your new unit, Quick start and Owners manual should be read in its entirety. The manual should be saved and kept on hand as a convenient reference.

All product names mentioned in this document are trademarks or registered trademarks of their respective owners.

In using the VG-88, either a guitar equipped with a GK-2A or one equipped with a GK-3 can be connected to it. If using a guitar equipped with a GK-3, substitute GK Volume knob (of the GK-3) wherever SYNTH VOL knob (of the GK-2A) appears in this document.

Copyright 2000 ROLAND CORPORATION All rights reserved. No part of this publication may be reproduced in any form without the written permission of ROLAND CORPORATION.

O w

n er's M

an u

al

As of January 15, 2005 (ROLAND)

Information When you need repair service, call your nearest Roland Service Center or authorized Roland distributor in your country as shown below.

EGYPT Al Fanny Trading Office 9, EBN Hagar A1 Askalany Street, ARD E1 Golf, Heliopolis, Cairo 11341, EGYPT TEL: 20-2-417-1828

REUNION Maison FO - YAM Marcel 25 Rue Jules Hermann, Chaudron - BP79 97 491 Ste Clotilde Cedex, REUNION ISLAND TEL: (0262) 218-429

SOUTH AFRICA That Other Music Shop(PTY)Ltd. 11 Melle St., Braamfontein, Johannesbourg, SOUTH AFRICA TEL: (011) 403 4105 FAX: (011) 403 1234

Paul Bothner(PTY)Ltd. 17 Werdmuller Centre, Main Road, Claremont 7708 SOUTH AFRICA TEL: (021) 674 4030

CHINA Roland Shanghai Electronics Co.,Ltd. 5F. No.1500 Pingliang Road Shanghai 200090, CHINA TEL: (021) 5580-0800

Roland Shanghai Electronics Co.,Ltd. (BEIJING OFFICE) 10F. No.18 3 Section Anhuaxili Chaoyang District Beijing 100011 CHINA TEL: (010) 6426-5050

Roland Shanghai Electronics Co.,Ltd. (GUANGZHOU OFFICE) 2/F., No.30 Si You Nan Er Jie Yi Xiang, Wu Yang Xin Cheng, Guangzhou 510600, CHINA TEL: (020) 8736-0428

HONG KONG Tom Lee Music Co., Ltd. Service Division 22-32 Pun Shan Street, Tsuen Wan, New Territories, HONG KONG TEL: 2415 0911

Parsons Music Ltd. 8th Floor, Railway Plaza, 39 Chatham Road South, T.S.T, Kowloon, HONG KONG TEL: 2333 1863

INDIA Rivera Digitec (India) Pvt. Ltd. 409, Nirman Kendra Mahalaxmi Flats Compound Off. Dr. Edwin Moses Road, Mumbai-400011, INDIA TEL: (022) 2493 9051

INDONESIA PT Citra IntiRama J1. Cideng Timur No. 15J-150 Jakarta Pusat INDONESIA TEL: (021) 6324170

KOREA Cosmos Corporation 1461-9, Seocho-Dong, Seocho Ku, Seoul, KOREA TEL: (02) 3486-8855

MALAYSIA Roland Asia Pacific Sdn. Bhd. 45-1, Block C2, Jalan PJU 1/39, Dataran Prima, 47301 Petaling Jaya, Selangor, MALAYSIA TEL: (03) 7805-3263

PHILIPPINES G.A. Yupangco & Co. Inc. 339 Gil J. Puyat Avenue Makati, Metro Manila 1200, PHILIPPINES TEL: (02) 899 9801

SINGAPORE SWEE LEE MUSIC COMPANY PTE. LTD. 150 Sims Drive, SINGAPORE 387381 TEL: 6846-3676

CRISTOFORI MUSIC PTE LTD Blk 3014, Bedok Industrial Park E, #02-2148, SINGAPORE 489980 TEL: 6243-9555

TAIWAN ROLAND TAIWAN ENTERPRISE CO., LTD. Room 5, 9fl. No. 112 Chung Shan N.Road Sec.2, Taipei, TAIWAN, R.O.C. TEL: (02) 2561 3339

THAILAND Theera Music Co. , Ltd. 330 Verng NakornKasem, Soi 2, Bangkok 10100, THAILAND TEL: (02) 2248821

VIETNAM Saigon Music Suite DP-8 40 Ba Huyen Thanh Quan Street Hochiminh City, VIETNAM TEL: (08) 930-1969

AUSTRALIA/ NEW ZEALAND Roland Corporation Australia Pty.,Ltd. 38 Campbell Avenue Dee Why West. NSW 2099 AUSTRALIA

For Australia Tel: (02) 9982 8266 For New Zealand Tel: (09) 3098 715

ARGENTINA Instrumentos Musicales S.A. Av.Santa Fe 2055 (1123) Buenos Aires ARGENTINA TEL: (011) 4508-2700

BARBADOS A&B Music Supplies LTD 12 Webster Industrial Park Wildey, St.Michael, Barbados TEL: (246)430-1100

BRAZIL Roland Brasil Ltda. Rua San Jose, 780 Sala B Parque Industrial San Jose Cotia - Sao Paulo - SP, BRAZIL TEL: (011) 4615 5666

CHILE Comercial Fancy II S.A. Rut.: 96.919.420-1 Nataniel Cox #739, 4th Floor Santiago - Centro, CHILE TEL: (02) 688-9540

COLOMBIA Centro Musical Ltda. Cra 43 B No 25 A 41 Bododega 9 Medellin, Colombia TEL: (574)3812529

COSTA RICA JUAN Bansbach Instrumentos Musicales Ave.1. Calle 11, Apartado 10237, San Jose, COSTA RICA TEL: 258-0211

CURACAO Zeelandia Music Center Inc. Orionweg 30 Curacao, Netherland Antilles TEL:(305)5926866

DOMINICAN REPUBLIC Instrumentos Fernando Giraldez Calle Proyecto Central No.3 Ens.La Esperilla Santo Domingo, Dominican Republic TEL:(809) 683 0305

ECUADOR Mas Musika Rumichaca 822 y Zaruma Guayaquil - Ecuador TEL:(593-4)2302364

EL SALVADOR OMNI MUSIC 75 Avenida Norte y Final Alameda Juan Pablo II, Edificio No.4010 San Salvador, EL SALVADOR TEL: 262-0788

GUATEMALA Casa Instrumental Calzada Roosevelt 34-01,zona 11 Ciudad de Guatemala Guatemala TEL:(502) 599-2888

HONDURAS Almacen Pajaro Azul S.A. de C.V. BO.Paz Barahona 3 Ave.11 Calle S.O San Pedro Sula, Honduras TEL: (504) 553-2029

MARTINIQUE Musique & Son Z.I.Les Mangle 97232 Le Lamantin Martinique F.W.I. TEL: 596 596 426860

Gigamusic SARL 10 Rte De La Folie 97200 Fort De France Martinique F.W.I. TEL: 596 596 715222

MEXICO Casa Veerkamp, s.a. de c.v. Av. Toluca No. 323, Col. Olivar de los Padres 01780 Mexico D.F. MEXICO TEL: (55) 5668-6699

NICARAGUA Bansbach Instrumentos Musicales Nicaragua Altamira D'Este Calle Principal de la Farmacia 5ta.Avenida 1 Cuadra al Lago.#503 Managua, Nicaragua TEL: (505)277-2557

PANAMA SUPRO MUNDIAL, S.A. Boulevard Andrews, Albrook, Panama City, REP. DE PANAMA TEL: 315-0101

PARAGUAY Distribuidora De Instrumentos Musicales J.E. Olear y ESQ. Manduvira Asuncion PARAGUAY TEL: (595) 21 492147

PERU Audionet Distribuciones Musicales SAC Juan Fanning 530 Miraflores Lima - Peru TEL: (511) 4461388

NORWAY Roland Scandinavia Avd. Kontor Norge Lilleakerveien 2 Postboks 95 Lilleaker N-0216 Oslo NORWAY TEL: 2273 0074

POLAND MX MUSIC SP.Z.O.O. UL. Gibraltarska 4. PL-03664 Warszawa POLAND TEL: (022) 679 44 19

PORTUGAL Roland Iberia, S.L. Portugal Office Cais das Pedras, 8/9-1 Dto 4050-465, Porto, PORTUGAL TEL: 22 608 00 60

ROMANIA FBS LINES Piata Libertatii 1, 535500 Gheorgheni, ROMANIA TEL: (266) 364 609

RUSSIA MuTek 3-Bogatyrskaya Str. 1.k.l 107 564 Moscow, RUSSIA TEL: (095) 169 5043

SPAIN Roland Iberia, S.L. Paseo Garca Faria, 33-35 08005 Barcelona SPAIN TEL: 93 493 91 00

SWEDEN Roland Scandinavia A/S SWEDISH SALES OFFICE Danvik Center 28, 2 tr. S-131 30 Nacka SWEDEN TEL: (0)8 702 00 20

SWITZERLAND Roland (Switzerland) AG Landstrasse 5, Postfach, CH-4452 Itingen, SWITZERLAND TEL: (061) 927-8383

UKRAINE TIC-TAC Mira Str. 19/108 P.O. Box 180 295400 Munkachevo, UKRAINE TEL: (03131) 414-40

UNITED KINGDOM Roland (U.K.) Ltd. Atlantic Close, Swansea Enterprise Park, SWANSEA SA7 9FJ, UNITED KINGDOM TEL: (01792) 702701

BAHRAIN Moon Stores No.16, Bab Al Bahrain Avenue, P.O.Box 247, Manama 304, State of BAHRAIN TEL: 17 211 005

CYPRUS Radex Sound Equipment Ltd. 17, Diagorou Street, Nicosia, CYPRUS TEL: (022) 66-9426

IRAN MOCO INC. No.41 Nike St., Dr.Shariyati Ave., Roberoye Cerahe Mirdamad Tehran, IRAN TEL: (021) 285-4169

ISRAEL Halilit P. Greenspoon & Sons Ltd. 8 Retzif Ha'aliya Hashnya St. Tel-Aviv-Yafo ISRAEL TEL: (03) 6823666

TRINIDAD AMR Ltd Ground Floor Maritime Plaza Barataria Trinidad W.I. TEL: (868)638 6385

URUGUAY Todo Musica S.A. Francisco Acuna de Figueroa 1771 C.P.: 11.800 Montevideo, URUGUAY TEL: (02) 924-2335

VENEZUELA Instrumentos Musicales Allegro,C.A. Av.las industrias edf.Guitar import #7 zona Industrial de Turumo Caracas, Venezuela TEL: (212) 244-1122

AUSTRIA Roland Elektronische Musikinstrumente HmbH. Austrian Office Eduard-Bodem-Gasse 8, A-6020 Innsbruck, AUSTRIA TEL: (0512) 26 44 260

BELGIUM/FRANCE/ HOLLAND/ LUXEMBOURG Roland Central Europe N.V. Houtstraat 3, B-2260, Oevel (Westerlo) BELGIUM TEL: (014) 575811

CZECH REP. K-AUDIO Kardasovska 626. CZ-198 00 Praha 9, CZECH REP. TEL: (2) 666 10529

DENMARK Roland Scandinavia A/S Nordhavnsvej 7, Postbox 880, DK-2100 Copenhagen DENMARK TEL: 3916 6200

FINLAND Roland Scandinavia As, Filial Finland Elannontie 5 FIN-01510 Vantaa, FINLAND TEL: (0)9 68 24 020

GERMANY Roland Elektronische Musikinstrumente HmbH. Oststrasse 96, 22844 Norderstedt, GERMANY TEL: (040) 52 60090

GREECE STOLLAS S.A. Music Sound Light 155, New National Road Patras 26442, GREECE TEL: 2610 435400

HUNGARY Roland East Europe Ltd. Warehouse Area DEPO Pf.83 H-2046 Torokbalint, HUNGARY TEL: (23) 511011

IRELAND Roland Ireland G2 Calmount Park, Calmount Avenue, Dublin 12 Republic of IRELAND TEL: (01) 4294444

ITALY Roland Italy S. p. A. Viale delle Industrie 8, 20020 Arese, Milano, ITALY TEL: (02) 937-78300

JORDAN AMMAN Trading Agency 245 Prince Mohammad St., Amman 1118, JORDAN TEL: (06) 464-1200

KUWAIT EASA HUSAIN AL-YOUSIFI & SONS CO. Abdullah Salem Street, Safat, KUWAIT TEL: 243-6399

LEBANON Chahine S.A.L. Gerge Zeidan St., Chahine Bldg., Achrafieh, P.O.Box: 16- 5857 Beirut, LEBANON TEL: (01) 20-1441

OMAN TALENTZ CENTRE L.L.C. P.O. BOX 37, MUSCAT, POSTAL CODE 113 TEL: 931-3705

QATAR Al Emadi Co. (Badie Studio & Stores) P.O. Box 62, Doha, QATAR TEL: 4423-554

SAUDI ARABIA aDawliah Universal Electronics APL Corniche Road, Aldossary Bldg., 1st Floor, Alkhobar, SAUDI ARABIA

P.O.Box 2154, Alkhobar 31952 SAUDI ARABIA TEL: (03) 898 2081

SYRIA Technical Light & Sound Center Rawda, Abdul Qader Jazairi St. Bldg. No. 21, P.O.BOX 13520, Damascus, SYRIA TEL: (011) 223-5384

TURKEY Ant Muzik Aletleri Ithalat Ve Ihracat Ltd Sti Siraselviler Caddesi Siraselviler Pasaji No:74/20 Taksim - Istanbul, TURKEY TEL: (0212) 2449624

U.A.E. Zak Electronics & Musical Instruments Co. L.L.C. Zabeel Road, Al Sherooq Bldg., No. 14, Grand Floor, Dubai, U.A.E. TEL: (04) 3360715

CANADA Roland Canada Music Ltd. (Head Office) 5480 Parkwood Way Richmond B. C., V6V 2M4 CANADA TEL: (604) 270 6626

Roland Canada Music Ltd. (Toronto Office) 170 Admiral Boulevard Mississauga On L5T 2N6 CANADA TEL: (905) 362 9707

U. S. A. Roland C

Manualsnet FAQs

If you want to find out how the VG-88 Roland works, you can view and download the Roland VG-88 Owner's Manual on the Manualsnet website.

Yes, we have the Owner's Manual for Roland VG-88 as well as other Roland manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Owner's Manual should include all the details that are needed to use a Roland VG-88. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Roland VG-88 Owner's Manual is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Roland VG-88 Owner's Manual consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Roland VG-88 Owner's Manual free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Roland VG-88 Owner's Manual, simply download the document to your computer. Once downloaded, open the PDF file and print the Roland VG-88 Owner's Manual as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.