Rangemaster Andesite 1.5 Granite Inset Ash Black User Guide PDF

1 of 4
1 of 4

Summary of Content for Rangemaster Andesite 1.5 Granite Inset Ash Black User Guide PDF

Instructions for: Andesite and Scoria sinks

IGNEOUS GRANITE SINKS

Installation Instructions &

Aftercare Information

U110645-01 Due to our policy of continual improvement, we reserve the right to change specifications without prior notice.

INSTALLATION Installer Please leave this leaflet with the user, as it contains valuable after care advice.

Tools Required

Ruler/Tape Measure Pencil

Masking Tape Safety Glasses

Kitchen Silicone Sealant Screwdriver

Hammer 35mm Hole Saw (for cutting tap hole)

Drill Jigsaw & Suitable Blade (if work top cutout is required)

Notes

nn During installation, take care to protect the sink from scuffs and scratches.

nn Do not stand on the sink.

nn During installation, do not stand the sink on its edges or corners. This may cause damage.

nn Avoid straining and over tightening of all plumbing fixtures connected to the sink.

nn Carefully check that the moulding and edges of the sink are dead level so that water will flow off the drainer.

nn The clamping brackets are suitable for worktops of between 3040 mm thickness (Fig. 1.1). If your worktop is a different size then it may require packing under the clamps or rebating (Fig. 1.2).

Preparing the Worktop Marking Out the Opening We recommend that you fit the sink to the worktop before permanently fixing the worktop to the cabinet.

1. Place the sink upside down on the worktop. Position the sink on the worktop as required. Make sure the cabinet framework will clear all parts of the sink. Using a soft, sharp pencil draw around the sink as accurately as possible (Fig. 1.3). Remove the sink.

2. Draw another line 10 mm inside the sink top outline this is the cutting line for the opening (Fig. 1.4).

3. Drill as large a hole as possible inside the cutting line. Using a pad saw, jigsaw or similar, cut out the opening up to the cutting line.

Sealing the Edges of the Opening. We recommend that porous edges around the cut-out are sealed using a waterproof sealant such as varnish, paint or wood glue . This will prevent swelling of the worktop should any small leaks occur (Fig. 1.5).

Worktop

Final position of sink

Cutting line for opening 10 mm

30 m

m

40 m

m

+ x

Less than 30 mm

Fig. 1.1

Fig. 1.2

Fig. 1.3

Fig. 1.4

Fig. 1.5

Preparing the Sink Tap Hole Preparation

Drilling a pre-marked hole for taps

nn Before drilling please read safety instructions supplied with hole saw.

nn The front face must be fully supported to prevent cracking when drilling or cutting.

nn WARNING! Any machining operation will produce fine particles of dust. Drilling or cutting MUST be carried out in a well-ventilated area.

1. Identify which pre marked tap hole(s) you will require. 2. Using a hole saw, drill out the tap hole part way from

the underside of the sink Fig. 1.6. Finish drilling the hole from the upper surface of the sink to ensure a clean hole.

3. It may be necessary to cool the tip of the drill with water to prevent burning. For this reason we recommend the use of a rechargeable drill. Take special care if using a mains electric drill around water.

4. Attach the tap, waste and overflow (where required) to the sink according to the manufacturers Instructions.

Applying the Silicon Sealant

nn DO NOT use Epoxi sealant or Epoxi adhesive.

Apply a bead of Silicone sealant(not included) to the underside of the sink flange. For final fit, make sure each sink clip is pulled back as shown in Fig. 1.7. Position the sink into the work top opening.

Secure the sink by pivoting the sink clips into the position Fig. 1.8 and tighten screws in the front, then tighten rear and side screws.

Waste Fittings Fit the waste fittings to the sink using the instructions supplied with them. Apply a uniform bead of silicone onto the underside of the rim of the sink, 1/4 inch from the outer edges of the rim.

Fitting the Sink 1. Turn the sink upside down and lay the worktop over

the sink. Swing each clip into place this is the most effective method, although if the worktop has been fitted to the cabinet the sink can be placed in the opening and fixed in position from underneath.

2. Centre the sink. Tighten the fixing screws in the sequence shown in Fig. 1.9.

nn DO NOT TIGHTEN FULLY AT FIRST ATTEMPT.

3. Remove any surplus sealing material or wipe away any excess sealant.

Check for Leaks: Supply user tubes to faucet

Supply riser tubes to shut off valves or lower connections

Fill sink with water and check for leak around drain

Release water from sink and check for possible leaks

Tighten a s needed

Drill starter hole from bottom. Finish drilling hole from top.

Fig. 1.6

SinkWorktop

1 2 3

Fig. 1.7

Fig. 1.8

1

2

3

4

5

6

7

8

9 10

11 12

Fig. 1.9

25 Year Guarantee We guarantee to replace any igneous granite sink that

breaks due to material or manufacturing defects within 25 years from the date of purchase.

The guarantee does not cover normal wear and tear occurring through use of the product.

For the guarantee to apply the owner must follow the use, care and cleaning instructions provided.

Accessories and waste fittings are not included in this guarantee.

Meadow Lane, Long Eaton, Nottingham, NG10 2GD, England

Tel: +44 (0) 115 946 4000 Fax: +44 (0) 115 973 6602 E-mail: consumers@rangemaster.co.uk

w w w.rangemaster.co.uk

16 DOP Reference BEF024

CA - DA

EN 13310 : 2015

Preparation of food, washing of dishes and discharge of domestic waste water

Kitchen sink made of: Granite Composite

After Care Day-to-day care Although your sink is made from extremely durable materials and will withstand a great deal of hard use, it can be scratched by hard or sharp objects. If the surfaces are to be kept in a blemish free condition reasonable care should be taken when handling such items.

nn DO NOT USE THE DRAINER AS A CHOPPING BOARD.

Cleaning Wash your sink using warm water, a soft cloth or non abrasive woven nylon pad and a non abrasive liquid cleaner or detergent. This can be done as often as the sink is used.

Metallic Abrasions or Heavy Stains:

Wipe the sink using a soft cloth or non abrasive woven nylon pad and a liquid scouring product. Apply the liquid scouring product sparingly and rub lightly. Repeat as necessary un

Manualsnet FAQs

If you want to find out how the Igneous Granite Inset Rangemaster works, you can view and download the Rangemaster Andesite 1.5 Granite Inset Ash Black User Guide on the Manualsnet website.

Yes, we have the User Guide for Rangemaster Igneous Granite Inset as well as other Rangemaster manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The User Guide should include all the details that are needed to use a Rangemaster Igneous Granite Inset. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Rangemaster Andesite 1.5 Granite Inset Ash Black User Guide is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Rangemaster Andesite 1.5 Granite Inset Ash Black User Guide consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Rangemaster Andesite 1.5 Granite Inset Ash Black User Guide free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Rangemaster Andesite 1.5 Granite Inset Ash Black User Guide, simply download the document to your computer. Once downloaded, open the PDF file and print the Rangemaster Andesite 1.5 Granite Inset Ash Black User Guide as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.