Polaris Victory Cross Roads, Cross Country Rider's Manual PDF

Pages 122
Year 2011
Language(s)
English en
1 of 122
1 of 122

Summary of Content for Polaris Victory Cross Roads, Cross Country Rider's Manual PDF

Page 4

Copyright 2010 Polaris Sales Inc... All information contained within this publication is based on the latest product information available at the time of publication... Product improvements or other changes may result in differences between this manual and the motorcycle... Depictions and/or procedures in this publication are intended for reference use only... No liability can be accepted for omissions or inaccuracies... Polaris Industries reserves the right to make changes at any time, without notice and without incurring obligation to make the same or similar changes to motorcycles previously built... Any reprinting or reuse of the depictions and/or procedures contained within, whether whole or in part, is expressly prohibited... All reference to RIGHT, LEFT, FRONT, REAR are from the operators perspective seated in a normal riding position... Features of VICTORY Motorcycles are covered by U... S... Patent Nos: 6,976,691; 6,407,663; D489670; D482311; D482304; D481980; D481973; D474142... The following are registered trademarks of Polaris Industries Inc... : POLARIS, THE WAY OUT, FREEDOM, VICTORY and VICTORY MOTORCYCLES... VICTORY CROSS ROADS and VICTORY CROSS COUNTRY are trademarks of Polaris Industries Inc... DUNLOP is a registered trademark of Dunlop Tire Corporation... LOCTITE is a registered trademark of Henkel Corporation... XM Ready is a registered trademark of XM Satellite Radio Inc... All rights reserved... iPod is a registered trademark of Apple Inc... Garmin and zumo are trademarks of Garmin Ltd... or its subsidiaries...

Page 5

Table of Contents Introduction ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 4 Safety ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 5 Component Identification ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 16 Instruments, Features & Controls... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 19 Pre-Ride Inspections ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 36 Operation ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 44 Maintenance... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 53 Cleaning and Storage... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 85 Warranty... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 93 Specifications ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 95 Audio System ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 98

Page 6

For the safe and enjoyable operation of your vehicle, be sure to follow the instructions and recommendations in this riders manual... Keep this manual with the motorcycle, especially when ownership changes... If your riders manual is misplaced or damaged, please purchase a replacement from your VICTORY dealer... All references in this manual to RIGHT, LEFT, FRONT or REAR are from the operators perspective when seated in a normal riding position... If you have questions about the opera- tion or maintenance of your motorcycle after you've read this manual, please see your VIC- TORY dealer... To locate the nearest authorized VICTORY dealer, call 1-800-POLARIS or visit www... polarisindustries... com... VICTORY motorcycles comply with all federal, state and local safety and emission regula- tions for the area of intended sale...

Page 7

This riders manual contains information that is essential to safe riding and proper mainte- nance of your VICTORY motorcycle... Anyone who uses the motorcycle (operators and pas- sengers) must read the riders manual before riding... Carefully read and understand the information found in the Safety section... Understand and follow the procedures outlined in the Maintenance section to keep your VICTORY motorcycle in top condition on the road or in storage... Bring the manual with you when you ride... Following the precautions and proce- dures in the manual will add to your enjoyment and help keep you riding safely... If you lose or damage this manual, you can purchase a new one through any authorized VICTORY dealer... The riders manual should be considered part of the motorcycle and remain with it if sold...

Page 8

Improper use of this motorcycle can result in serious injury or death to you, your passenger and others... To minimize the risk of injury, read and understand the information contained in this section before operating the motorcycle... This section contains safety information specific to the VICTORY motorcycle, as well as information about general motorcycle safety... Anyone who rides the motorcycle (operators and passengers) must follow these safety precautions...

Page 9

Ride defensively, as if you are invisible to other motorists, even in broad daylight... A motorist's failure to see or recognize a motorcycle is the leading cause of automobile/ motorcycle accidents... Ride where you're clearly visible to other motorists, and observe their behavior carefully...

Page 10

the road has potholes, or is otherwise rough or uneven... the road contains sand, dirt, gravel or other loose substances... the road is wet, icy or oily... the road contains painted surfaces, manhole covers, metal grating, railway crossings or other

Page 11

Wear gloves, a jacket, heavy boots and long pants to prevent or reduce injury from abra- sions, lacerations or burns should the motorcycle fall... Wear boots with low heels, as high heels can catch on pedals or footrests... The combination of boots and pants should com- pletely cover legs, ankles and feet, protecting skin from engine and exhaust system heat...

Page 12

Parking the Motorcycle When leaving the motorcycle unattended, turn the engine off... Remove the ignition key to prevent unauthorized use... Park the motorcycle where people are not likely to touch the hot engine or exhaust system or place combustible materials near these hot areas... Do not park near a flammable source such as a kerosene heater or an open flame, where hot components could ignite combustible mate- rials... Park the motorcycle on a firm, level surface... Sloped or soft surfaces may not support the motorcycle... If you must park on a slope or soft surface, follow the precautions outlined on page 51...

Page 13

Distribute weight evenly on both sides of the motorcycle... Maintain even weight distribu- tion by checking accessories and cargo to make sure theyre securely attached to the motorcycle before riding and whenever you take a break from riding... Uneven weight dis- tribution, or accessories or cargo that shift suddenly while youre riding can make the motorcycle hard to handle and could cause loss of control...

Page 14

Gasoline is highly flammable and explosive under certain conditions... Always exercise extreme caution whenever handling gasoline... Always turn off the engine before refueling... Always refuel outdoors or in a well-ventilated area... Open the fuel cap slowly... Do not overfill the tank... Do not fill the tank neck... Do not smoke or allow open flames or sparks in or near the area where refueling is performed or

Page 15

Failure to perform safety maintenance as recommended can result in difficult handling and loss of control, which could result in serious injury or death... Always perform the safety maintenance procedures as recommended... Perform maintenance and repairs promptly as outlined in the VICTORY service manual, or see your authorized VICTORY dealer for service...

Page 16

Safety Gross Vehicle Weight Rating (GVWR) WARNING! Exceeding the gross vehicle weight rating of your motorcycle can reduce stability and han- dling and could cause loss of control... NEVER exceed the GVWR of your motorcycle... The maximum load capacity of your motorcycle is the maximum weight you may add to your motorcycle without exceeding the GVWR... This capacity is determined by calculating the difference between your motorcycles GVWR and wet weight... Refer to the specification section of this manual or the Manufacturing Information/VIN label on the motorcycle frame for model-specific information... Refer to the Safety and Informa- tion Labels section in this manual for location on the motorcycle... When determining the weight you will be adding to your motorcycle, and to ensure you do not exceed the maximum load capacity, include the following: operator body weight passenger body weight weight of all riders apparel and items in or on apparel weight of any accessories and their contents weight of any additional cargo on the motorcycle

Page 17

Safety Safety and Information Labels Labels are model-specific and market-specific... Your motorcycle may not contain all of the labels shown... 1... Manufacturing Information Label 2... Vehicle Emission Control Information (VECI) 3... Noise Emission Control Information (NECI) 4... Operator/Fuel Warning 5... Cargo Information (in saddlebags) 6... Shock Air Pressure label 7... Saddlebag Warning 8... Highway Bar Warning

Page 18

Identification Ignition Key Number The ignition key number is stamped on the small metal tag attached to the key ring... Remove the tag and record the number on page 97... Store the tag in a safe place... Additional keys can be copied from one of the original keys... A VICTORY key blank is required... If you lose both original keys, you will need the following:

Page 19

Right Side View 1... Exhaust Mufflers 2... Drive Belt Guard 3... Drive Sprocket (under cover) 4... Engine Oil Fill Cap / Dipstick 5... Rear Brake Fluid Reservoir 6... Rear Brake Pedal 7... Air Filter 8... Headlamp 9... Mirror 10... Fuel Tank 11... Access Cover 12... Fuse Box (under cover) 13... Accessory Fuse (under

Page 20

Console (CROSS COUNTRY) 1... Speakers 2... Mode Switch 3... Fuel Gauge 4... Speedometer 5... Indicator Lamp Display 6... Multi-Function Display 7... Tachometer 8... Volt Meter 9... Left Handlebar Switches 10... Audio Control Switches 11... +12-Volt Accessory Outlet 12... Radio Display 13... Heated Grip Switch (if equipped) 14... Cruise Control Switches (if equipped) 15... Right Handlebar Switches

Page 21

Parking Lights On In the PARKING LIGHTS ON position, the taillight, indicator lights and license plate light illuminate... The radio can be operated and the instrumentation is active... The emergency flashers can be activated, and the ignition key can be removed... You must push the ignition key into the switch while selecting this position...

Page 22

Check Engine This lamp illuminates momentarily when the ignition switch is in the ON position and the engine is off... This indicates proper function... This lamp will illuminate if the engine is disabled by the sidestand interlock switch... See page 34... The light will also remain on if the tilt sensor shuts down the engine... See page 32... If this lamp illuminates while the engine is running, contact an authorized VICTORY dealer promptly for diagnosis... If abnormal sensor or engine operation is detected the light will remain on as long as the fault condition exists... Retrieve the error codes for diagnosis... See page 26...

Page 23

Odometer The odometer displays total distance traveled... Trip Odometers The ignition switch must be in the ON or PARK position to access the trip odometers... The trip odometers (Trip 1 and Trip 2) display total distance traveled since being reset... To reset a trip odometer, toggle to the trip odometer, then press and hold the mode button until the trip odometer resets to zero... Fuel Level The fuel level displays bar graph- ics between empty (E) and full (F) to indicate the fuel level... Engine Speed Engine speed displays in revolutions per minute (RPM)... DC Voltage (Optional) The volt meter displays battery voltage... If the engine is not running, approximate battery voltage displays... If the engine is running, approximate charging voltage displays... Gear Position Gear position displays only when the vehicle is moving and the clutch is engaged... If the vehicle stops moving, or if the clutch is disengaged, -- will show in the display... Temperature (Optional) The key must be in the ON or PARK position to display ambient air temperature...

Page 24

option... 5... Repeat the procedure to change remaining display settings... Clock Tip: The clock must be reset any time the battery has been disconnected or discharged... 1... Turn the key to ON or PARK... Use the mode button to toggle to the odometer display... 2... Press and hold the mode button until the hour segment flashes... Release the button... 3... With the segment flashing, tap the mode button to advance to the desired setting... 4... Press and hold the mode button until the next segment flashes... Release the button... 5... Repeat steps 3-4 twice to set the 10-minute and 1-minute segments... After completing the

Page 25

Instruments, Features and Controls Instrument Cluster (CROSS ROADS) Multi-Function Display Engine Error Codes The error screen displays only when the CHECK ENGINE light is on or when it goes on and off during one ignition cycle... Error codes are not stored... When the key is turned OFF, the code and message is lost, but will reappear if the fault reoccurs after restarting the engine... If the CHECK ENGINE indicator lamp illu- minates, retrieve the error codes from the display... 1... If the error codes are not displayed, use

Page 26

Speedometer The speedometer displays vehicle speed in either miles per hour or kilometers per hour... Tachometer The tachometer displays engine speed in revolutions per minute (RPM)... A red line on the face of the gauge indicates the maximum safe engine speed... WARNING! Excessive engine speed can cause engine damage or failure, which could result in serious injury or death... Do not allow engine speed to exceed the red line... Fuel Gauge The fuel gauge displays fuel level... The key must be in the ON or PARK position... For the most accurate reading, sit on the motorcycle and bring it to the upright position... Volt Meter When the key is in the ON position, the volt meter displays battery voltage... If the engine is not running, approximate battery voltage displays... If the engine is running, approximate charging voltage displays...

Page 27

Check Engine This lamp illuminates momentarily when the ignition switch is in the ON position and the engine is off... This indicates proper function... If this lamp illuminates while the engine is running, contact an authorized VICTORY dealer promptly for diagnosis... The light will remain on if the tilt sensor shuts down the engine... See page 32... If abnormal sensor or engine operation is detected the light will remain on as long as the fault condition exists... Retrieve the error codes for diagnosis... See page 26... This lamp is also known as a malfunction indicator lamp (MIL)...

Page 28

Engine Error Codes The error screen displays only when the CHECK ENGINE light is on or when it goes on and off during one ignition cycle... Error codes are not stored... When the key is turned OFF, the code and message is lost, but will reappear if the fault reoccurs after restarting the engine... If the CHECK ENGINE indicator lamp illumi- nates, retrieve the error codes from the display... 1... If the error codes are not displayed, use the

Page 29

option... 5... Repeat the procedure to change remaining display settings... Clock Tip: The clock must be reset any time the battery has been disconnected or discharged... 1... Turn the key to ON or PARK... Use the mode button to toggle to the odometer display... Tip: If LOW FUEL is flashing, the display will not enter the CLOCK SET mode... 2... Press and hold the mode button until the hour segment flashes... Release the button... 3... With the segment flashing, tap the mode button to advance to the desired setting... 4... Press and hold the mode button until the next segment flashes... Release the button... 5... Repeat steps 3-4 twice to set the 10-minute and 1-minute segments... After completing the

Page 30

Instruments, Features and Controls Instrument Cluster (CROSS COUNTRY) Multi-Function Display Odometer/Trip Odometer The odometer displays the total distance traveled by the vehicle... The trip odometer displays distance traveled since the trip odometer was reset... To view the trip odometer, turn the key to the ON position... Use the mode button to toggle to the trip odometer... To reset the trip odometer, toggle to the trip odometer, then press and hold the mode button until the trip odometer resets... Gear Position Gear position displays only when the vehicle is moving and the clutch is engaged... If the vehicle stops moving, or if the clutch is disengaged, -- will show in the display... Temperature The key must be in the ON or PARK position to display ambient air temperature...

Page 31

Move the switch to the left to activate the left turn signals... Move the switch to the right to activate the right turn signals... A signal will deacti- vate automatically when speed or distance reach predetermined levels... To cancel a signal manually, move the switch to the center position and push it inward... Momentary Feature: Move the turn signal switch left or right and hold it in that position for at least one second... The momentary feature will acti- vate and the signal will then cancel when the switch is released...

Page 32

Instruments, Features and Controls Left Handlebar Switches Audio Switches (if equipped) Refer to the Audio System section of this manual (beginning on page 98) for audio systems opera- tion... Mode Button The mode button is located on the front side of the left handlebar switch... Use the mode button to tog- gle through the modes of the multi-function dis- play... See page 26... Use the mode button to set the display units to either standard or metric units of measurement (CROSS COUNTRY)... See page 27... Tip: If Err displays while toggling through the features,

Page 33

Engine Starter Switch The starter switch is located on the right handlebar... Use the starter switch to start the engine and operate in reverse (if equipped)... The switch will operate only when the engine stop/run switch is in the RUN position and the transmis- sion is in neutral (or the clutch is disengaged)... The reverse lever (if equipped) must also be disengaged... Tip: If the reverse system fuse has blown, the starter switch will

Page 34

License Plate The license plate module is equipped with an LED light to illluminate the license plate... Always make sure the license plate is properly installed before operating the motorcycle... 1... Position the license plate at the center of the rear fender, aligning the bottom edge of the

Page 35

Instruments, Features and Controls Brakes The front brake lever activates the front brake calipers... The rear brake pedal activates the rear brake caliper... For maximum brake effectiveness, apply the front brake lever and the rear brake pedal together... Front Brake Lever The front brake lever is located on the right handlebar... This lever controls only the front brakes... The front brakes should be applied simultaneously with the rear brakes... To apply the front brake, pull the lever toward the handlebar... See page 49 for braking procedures... Front brake lever reach (distance to the hand grip) is adjustable... 1... Pull and hold the lever away from the hand grip... 2... To increase reach distance, rotate the adjuster to align a lower number with the arrow on

Page 36

Sidestand The sidestand is located on the left side of the motorcycle... Sidestand Interlock Switch This vehicle is equipped with a sidestand interlock switch that prevents the engine from starting, although it will crank, if the sidestand is extended and the transmission is in gear... If this occurs, the check engine lamp will illuminate until the side- stand is retracted or until the transmission is placed in neutral... The interlock switch error code will also display in the diag- nostic screen... The SPN will read 520267 and the FMI will read 31... See page 26... Turn the ignition switch off to clear the code... Sidestand Operation To park the motorcycle, swing the end of the sidestand downward and away from the motor- cycle until it is fully extended... Lean the motorcycle to the left until the sidestand firmly sup- ports the motorcycle... To retract the sidestand, straddle the motorcycle and bring it to the fully upright position... Swing the end of the sidestand upward and toward the motorcycle until it is fully retracted...

Page 37

Instruments, Features and Controls Saddlebag Lock Use the ignition key to lock and unlock the saddle- bag doors... The doors should be locked before riding... To lock a door, place the key in the lock and turn it counter-clockwise... To unlock a door, turn the key clockwise... After unlocking a door, press the door lock to release the latch and open the door... Refer to the Gross Vehicle Weight Rating informa- tion beginning on page 14 for loading information...

Page 38

Pre-Ride Inspections To keep your motorcycle in safe operating condition, always perform the recommended pre- ride inspections before each ride... This is especially important before making a long trip and when removing the motorcycle from storage... WARNING! Failure to perform the recommended pre-ride inspections could result in component failure while riding, which could result in serious injury or death... Always perform the pre-ride inspections before each ride... When inspection reveals the need for adjustment, replacement or repair, perform the service promptly... You must be familiar with all instruments and controls to perform the pre-ride inspections... Tip: During the pre-ride inspections you may use products that are potentially hazardous, such as oil or

Page 39

General Engine Oil Level Check the oil level on the dipstick... Fuel Level View the fuel gauge or information bar... Tires Inspect condition, pressure and tread depth... Brake Operation Inspect pedal and lever movement... Brake Fluid Levels Check front and rear brake fluid levels... Brake Components Inspect hoses, connections, brake pads... Throttle Inspect hand grip and throttle freeplay... Clutch (Mechanical) Check lever operation and freeplay... Front Suspension Check for leaks, debris and damage... Steering Check for smooth operation... Rear Suspension Check shock movement and air pressure, verify ground clearance... Drive Belt Check for wear, damage, proper deflection... Sidestand Verify smooth operation, inspect pivot bolt, spring and pad... Fasteners Inspect for loose, damaged or missing fasteners... Mirrors Adjust for proper rear view...

Page 40

WARNING! Operating the engine with too much or too little oil can cause serious engine damage or engine seizure, which could result in loss of control and serious injury or death... Do not operate the motorcycle with the oil level above the FULL mark or below the ADD mark...

Page 41

Pre-Ride Inspections Tires Tire Pressure Check tire pressure before riding, when the tires are cold... This will provide the most accurate reading, as riding warms the tires and increases tire air pressure... Adjust tire pressure as needed based on the total weight of your intended load... See page 74... Tire Condition Inspect the tire sidewalls, road contact surface and tread base... If inspection reveals cuts, punctures, cracks or other wear or damage, replace the tire before riding... Tire Tread Depth Measure the tread depth near the center of the tread on both tires... See page 73... Replace any tire with a tread depth of less than 1/16 (1... 7 mm)...

Page 42

for fastener torque values... WARNING! Brake fluid leaks or low brake fluid levels could cause brake system failure, which could result in serious injury or death... Do not operate the vehicle with low brake fluid levels or when leaks are evident (dampness or stains from dried fluid)... See your VICTORY dealer for service...

Page 43

Pre-Ride Inspections Brake Pads Inspect each front brake pad on both sides of the front disc... Inspect each rear brake pad on both sides of the rear disc... When the thinnest point of the friction material has worn to the minimum recommended thickness, see your VICTORY dealer for brake pad replacement... Replace brake pads when friction material thickness reaches 1... 0 mm... When checking brake pad friction material thickness, check each brake caliper for damp- ness or stains from leaking or dried brake fluid... If inspection reveals signs of fluid leakage, do not operate the vehicle... See your VICTORY dealer for service... See page 72 for brake disc inspection...

Page 44

sure label located in the left saddlebag near the air fitting... WARNING! Inadequate ground clearance could result in components contacting the ground, causing loss of control and serious injury or death... Always ensure ground clearance is at specification...

Page 45

Pre-Ride Inspections Sidestand 1... On level ground, straddle the motorcycle and bring it to the fully upright position... 2... Move the sidestand up to the stored position and down to the fully extended position sev-

Page 46

Perform the break-in maintenance outlined in the maintenance section of this manual... Break-in maintenance should be performed by an authorized VIC- TORY dealer... Break-in maintenance must include inspection, adjustments, fas- tener tightening and an engine oil and filter change... Performing break-in maintenance at the required odometer reading helps ensure peak engine per- formance, minimal exhaust emissions and maximum service life of the engine...

Page 47

Operation Fueling Always refuel on level ground with the sidestand down... Review the fuel warnings... See page 12... Use only the recommended fuel... See page 97... Hold the nozzle while filling... Do not rest the weight of the nozzle and hose on the filler neck... Do not leave the nozzle unattended... WARNING! Overflows or spilled gasoline could contact a hot engine or exhaust system and cause a fire, which could result in serious injury or death... Do not allow gasoline to contact hot components... 1... Insert the fuel nozzle into the fuel tank filler neck... 2... Fill the fuel tank to a level just below the bottom of the fuel filler insert... WARNING! Fuel expands in the fuel tank... Do not overfill... To prevent leaks, make sure the fuel filler cap is properly seated... 3... Always lock the fuel cap before riding... An open fuel cap could contact the handlebars... NOTICE: Fuel can damage painted surfaces and plastic parts... If gasoline spills on the any part of the

Page 48

Operation Starting the Engine The starter interlock system allows the engine to be started only when the transmission is in neutral, or when the transmission is in gear with the clutch disengaged (clutch lever pulled in) and the sidestand retracted... Tip: If the motorcycle runs out of fuel, prime the system before attempting to restart the engine... See

Page 49

Operation Shifting Gears WARNING! Forced shifting (with clutch engaged) could cause damage to the engine, transmission and drive train... Such damage could cause loss of control, which could result in serious injury or death... Always pull the clutch lever fully toward the handlebars to disengage the clutch before shifting gears... This motorcycle is equipped with a six-speed transmission... The sixth gear is overdrive... Neutral is located between first and second gear... Tip: The transmission is in neutral if you

Page 50

Accelerating Accelerate by opening the throttle (rolling the throttle control grip rearward)... For even accel- eration, open the throttle with a smooth, continuous motion... When you reach the recom- mended speed for upshifting, shift up one gear... WARNING! Accelerating abruptly could cause your body to shift rearward suddenly, which could result in loss of control... Accelerating abruptly could also cause loss of control on low traction surfaces... Loss of control could result in serious injury or death... Always accelerate gradually, especially on wet, slippery or other low traction surfaces...

Page 51

Using Cruise Control (if equipped) If equipped, the cruise control is located on the right handlebar... Read this section and understand how to safely operate this fea- ture before using the cruise control... WARNING! Improper operation of cruise control could cause loss of control and result in serious injury or death... Follow all cruise operation procedures carefully... Never use cruise control when roads are wet or slippery... Do not use cruise control when riding in heavy or congested traffic...

Page 52

Operation Using Cruise Control (if equipped) Resume Speed After disengaging the cruise control with the brake, throttle or clutch, wait at least 3 seconds, then press the resume but- ton (RES) to return to the set speed... If the resume button is pressed within 3 seconds of disengag- ing, the cruise control may not engage, even if the cruise con- trol indicator illuminates... This is a safety feature that prevents cruise control from engaging if a button is stuck... To continue using cruise control, disengage it... Wait at least 3 seconds, then press the resume button... Tip: Turning the cruise control master switch off will erase the set

Page 53

Operation Stopping the Engine Before stopping the engine, bring the motorcycle to a complete stop... Shift to neutral or dis- engage the clutch... WARNING! Stopping the engine with the transmission in gear while the motorcycle is moving could cause loss of rear wheel traction or engine and transmission damage, which could cause loss of control and serious injury or death... Always stop the engine after the motorcycle is fully stopped and the transmission is in neutral... If the engine stops unexpectedly while the motorcycle is moving, guide the motorcycle to a safe location off the road and away from traffic... 1... When fully stopped, shift into neutral... 2... Move the engine stop/run switch to the STOP position... 3... Move the ignition switch to the OFF position... Remove the ignition key... Tip: A momentary clicking sound from the IAC valve is normal when the key is first turned to the OFF

Page 54

Before Operating in Reverse: always sit on the motorcycle with legs astride and both feet on the ground... always check for obstacles or people behind the motorcycle... always retract the sidestand fully... always make sure the motorcycle is completely stopped... NEVER Operate in Reverse: when not properly seated... when in an area where obstacles or bystanders are present... with a passenger on board... A passenger can obstruct your view and maneuverability... when on loose or slippery surfaces... Loss of foot traction could cause a tip-over... while the motorcycle is moving forward... when on a grade or uneven surfaces... Reverse Operation Procedure 1... Always check for obstacles or people behind the motorcycle... Be aware that the front

Page 55

Failure to follow recommended precautions and procedures could result in severe injury or death... Always heed all safety precautions and follow all operation, inspection and maintenance procedures outlined in this manual... Improperly installed or adjusted components can make the motorcycle unstable or hard to handle...

Page 56

Periodic Maintenance Inspect, clean, lubricate, adjust and replace parts as necessary... When inspection reveals the need for replacement parts, use genuine VICTORY parts available from your VICTORY dealer... Record service and maintenance information in the Maintenance Log beginning on page 56... Perform maintenance at the intervals specified in the periodic maintenance table beginning on page 55... Perform the procedures more frequently if normal use of the motorcycle includes: high speed operation for extended periods low speed operation for extended periods operation in dusty or otherwise adverse conditions

Page 57

Control Cables 69 70 I I L I L I L I L I L Crankcase Vent 67 I I I I I I I I I I I Drive Belt 60 I I I I I I R I I I I Drive Belt Adjustment 63 P Adjust with each tire change thereafter Engine Oil & Filter* 57 R R R R R R R R R R R Exhaust System 81 I I I I I I I I I I I Fasteners 77 I I I I I I I I I I I Front Brake Lever 72 L L L L L L L L L L L Front Fork Oil** 66 I I I R I I R I I R I Front Fork / Axle 66 I I I I I I I I I I I Fuel System 67 I I I I I I I I I I I Fuel Filter - Please see your dealer for this service... R Headlamp 78 I I I I I I Ignition Switch / Locks 76 L L L L L L L L L L Radio/Radio Software 98 Update annually... Please see your dealer... Rear Wheel Align 63 I I I I I I I I I I I Rear Shock 64 I I I I I I I I I I I Rear Brake Pedal 71 I I L I L I L I L I L Road Test 82 P P P P P P P P P P P Sidestand 77 I I L I L I L I L I L Sidestand Pad 43 I I I I I I I I I I I Spark Plugs 74 I I I I I I R I I I I Steering Head Bearings 66 I I I L I I L I I L I Swingarm 65 I I I I I I I I I I I Throttle Cable <$ele

Page 58

Maintenance Performed Miles / Km Notes Performed by

Page 59

changing the oil... CAUTION! Hot engine and exhaust components can cause burns to skin and can ignite a fire if exposed to flammable materials... Always park the motorcycle clear of flammable materials and where people are not likely to contact hot components... 2... Position the motorcycle securely on the sidestand... 3... Place a drain pan under the drain plug and oil filter... Remove the drain plug and seal...

Page 60

Fuel Tank Removal / Installation Before beginning, be prepared to place the fuel tank in a secure location with a drain pan positioned to catch any fuel that may leak or drip from disconnected hoses or fittings... 1... Remove the seat and both side covers... 2... Remove the right side access cover... 3... With the engine and exhaust cool, wrap a clean shop

Page 61

NOTICE: The 90-degree fuel pump fitting can be damaged if improperly installed... The fitting must point toward the rear of the bike when installing the tank... If the tank does not align with the rear frame mounts, do not force it into position... Verify the orientation of this fitting...

Page 62

Maintenance Drive Belt Condition Replace the drive belt if it is cracked or has bro- ken teeth or frayed edges... No matter its condition, the drive belt should be replaced at periodic inter- vals... See the VICTORY Service Manual or an authorized VICTORY dealer... DO NOT attempt to check belt tension if the belt has been exposed to rain or washing within a 24 hour period or if the belt is hot from riding... Allow the belt to cool down to ambient temperature before measuring belt tension... Replace the drive belt and both sprockets as a set if the drive belt has over 5,000 miles (8,000 km) of service at the time of damage or failure...

Page 63

wet... Improper adjustment will result... Checking drive belt tension involves using the belt tension gauge (P/N PV-43532)... You can also use a Sonic Tension Meter if available... Before beginning this procedure: Make sure the drive system is clean, dry, and at room

Page 64

slightly off the floor... CAUTION! Make sure the motorcycle is stable when elevated... Injury may occur if the motorcycle tips or falls... 2... Place the transmission in neutral... 3... Rotate the rear wheel in a forward direction until the

Page 65

Drive Belt Cleaning Cleaning the drive belt will maximize belt and sprocket life and minimize drive line noise... Clean the belt at every tire change... Clean the belt more often if riding in dirty, dusty or high debris environments... 1... Mix a few drops of mild dish soap with a cup of warm water... 2... Use a soft nylon brush to clean the belt and sprocket teeth with the soapy water... Clean

Page 66

If the VICTORY air pump and gauge are not available, use the gauge provided in the tool kit, and a pressurized air source with a maximum line pressure of 72 PSI (496 kPa)... After using this gauge, remove it quickly to minimize leakage... Expect to lose about 4 PSI (27... 6 kPa) with each pressure check when using this gauge... Use only a dry air source, such as a system with a water separator or air line dryer, to prevent moisture from entering the shock... CAUTION! Air pressure increases VERY quickly when using pressurized air... Wear eye and face protection...

Page 67

the suspension moves freely without binding... Listen for abnormal noises... 2... Elevate and support the motorcycle with the rear tire slightly off the floor... CAUTION! Make sure the motorcycle is stable when elevated... Injury may occur if the motorcycle tips or falls... 3... Grasp the rear-most surface of the rear tire and attempt to move the wheel side-to-side... If

Page 68

4... Fork oil condition and level affects front suspension perfor- mance and internal component wear... Replace fork oil at the recommended intervals... Special tools are required to perform this procedure... See the VICTORY Service Manual or your authorized VICTORY dealer...

Page 69

Maintenance Fuel System Components 1... Inspect fuel hoses for cracks or damage... 2... Inspect hose connections at the fuel tank and at the fuel rail for dampness or stains from

Page 70

Throttle Cable Freeplay Throttle freeplay is the amount of throttle control grip movement from the rest position to the point of cable resistance... Measure this distance... Freeplay should be 2-4 mm... Adjust throttle freeplay as needed... 1... Position the front wheel straight ahead... Stop the

Page 71

performance... Verify proper routing and smooth movement... Inspect for damage to the external casing, and inspect exposed cable wire for fraying, kinks or corrosion... Replace any damaged, sticky or sluggish cable... 1... Disconnect the cable at the throttle body... 2... Apply a light film of VICTORY All Purpose Grease or equivalent to the barrel end... 3... Reconnect the cable and adjust freeplay as needed...

Page 72

performance... Verify proper routing and smooth movement... Inspect for damage to the external casing, and inspect exposed cable wire for fraying, kinks or corrosion... Replace any damaged, sticky or sluggish cable... 1... Disconnect the cable at the clutch lever and at the primary cover... 2... Lubricate the barrel ends with VICTORY All Purpose Grease or equivalent... 3... Reconnect the cable and adjust freeplay as needed...

Page 73

Using the wrong fluid or allowing air or contaminants into the fluid system can damage the system seals or result in a malfunction that could lead to serious injury or death... Use only DOT 4 brake fluid from a sealed container... Do not operate the front brake with the reservoir cover removed... Fluid could overflow from the reservoir and allow air to enter the system... Air in the brake system could cause the brakes to malfunction... An over-full reservoir may cause brake drag or brake lock-up, which could result in serious injury or death... Maintain brake fluid at the recommended level... Do not overfill...

Page 74

3... Clean discs if minor squeaks develop due to dirt or dust... Apply VICTORY Brake Cleaner (P/N 2872191) to a clean shop towel and wipe disc... DO NOT allow brake cleaner to contact painted or plastic parts... Read all precautions on the label...

Page 75

Operating the motorcycle with improper tires or with improper or uneven tire pressure could cause loss of control or accident... Always use the correct size and type of tires specified for your vehicle... Always maintain proper tire pressure as recommended in the owner's manual and on safety labels...

Page 76

Maintenance Tires Tire Pressure Riding warms the tires and increases tire air pressure... For an accurate reading, check tire pressure before riding... Adjust tire pressure as recommended for the total weight of your intended load (see table)... WARNING! Do not exceed the maximum recommended inflation pressure to seat the bead... Tire or rim failure may result...

Page 77

Battery electrolyte is poisonous... It contains sulfuric acid... Serious burns can result from contact with skin, eyes or clothing... Antidote: External: Flush with water... Internal: Drink large quantities of water or milk... Follow with milk of magnesia, beaten egg, or vegetable oil... Call physician immediately... Eyes: Flush with water for 15 minutes and get prompt medical attention... Batteries may produce explosive gases... Keep sparks, flame, cigarettes, etc... away... Ventilate when charging or using in an enclosed space... Always shield eyes when working near batteries KEEP OUT OF REACH OF CHILDREN...

Page 78

Maintenance Battery Installation WARNING! Improperly connecting or disconnecting battery cables can result in an explosion and cause serious injury or death... When removing the battery, always disconnect the negative (black) cable first... When reinstalling the battery, always connect the negative (black) cable last... 1... Place the battery in the battery compartment

Page 79

Side Covers Remove the left side cover to access the electronic con- trol module, diagnostic connector and chassis-to-engine harness connector... Remove the right side cover to access the fuses, rear suspension air fitting, clutch cable adjuster, purge valve and flasher unit... Remove both side covers to access the seat screws... 1... Pull outward at each corner of the side cover to dis-

Page 80

1... Verify that tire pressure is at specification... See page 74... 2... Verify that rear suspension ride height (preload) is at specification... See page 64... 3... Position the motorcycle on a level surface with the headlight 25 feet (7... 6 m) from a wall... 4... With the operator and passenger (if applicable) on board, bring the motorcycle to the

Page 81

Headlight Lamp Replacement High Intensity Discharge (HID) Lamps (CROSS COUNTRY) High intensity discharge lamps should be handled only by a trained technician wearing the appropriate protective gear... See the VICTORY Service Manual or an authorized VICTORY dealer...

Page 82

Tip: Use the fuse puller provided in the tool kit to remove a fuse... 1... Remove the right side cover... 2... Lift the release tab and slide the fuse box

Page 83

Exhaust System Inspection Check the exhaust system for stains from leaking exhaust gasses... Replace damaged or leak- ing exhaust gaskets... See the VICTORY Service Manual or your authorized VICTORY dealer... Check all exhaust system fasteners... Tighten loose clamps and fasteners... Do not overtighten...

Page 84

Maintenance Elevating the Motorcycle WARNING! Serious injury or death can occur if the motorcycle tips or falls... Make sure the motorcycle will not tip or fall while elevated or while on the sidestand... Some procedures require raising the motorcycle to remove weight from the component being inspected... Elevate the motorcycle by placing a stable, flat platform jack or lift mechanism on a firm, flat surface and lifting under the engine crankcase... The platform should be a mini- mum of 12 inches (30 cm) square... DO NOT attempt to lift the motorcycle without proper equipment... Always secure the motorcycle properly before lifting so it cannot tip or fall when elevated...

Page 85

Possible Cause Possible Remedy/Action Battery Discharged Fully charge the battery... See page 76... Battery Cables Loose or Corroded Inspect battery cables and connections... Spark Plug(s) Fouled Inspect spark plugs... See page 74... Spark Plug Wire(s) Loose or Wet Inspect spark plug wires, ensure dry/secure... Contaminated Fuel Inspect fuel for water / contamination... See dealer... Engine Oil Level Incorrect Or Wrong Type Inspect level and quality of oil... See page 38... Loose, Broken, Shorted Ignition Coil Wires Inspect coil primary wires... See dealer... Air Intake Restricted Inspect air filter... See page 58...

Page 86

Service Manual Availability Some procedures are beyond the scope of this manual... See your dealer to purchase a VIC- TORY Service Manual for your motorcycle... Some procedures provided in the Service Manual require specialized knowledge, equipment, and training... Be sure you have the required technical skills and tools that are needed before you attempt ANY service on your motorcycle... Please contact your VICTORY dealer before attempting any service work that is beyond your level of technical knowledge or experience, or if the work requires specialized equipment...

Page 87

Cleaning and Storage VICTORY Cleaning Products This section provides tips on the very best way to clean, polish and preserve every surface of your beautiful new VICTORY Motorcycle... We recommend the use of our new Pure VIC- TORY cleaning and polishing products and accessories, which have been specially designed to offer the best care possible for your VICTORY motorcycle... In addition to the products recommended in this section for cleaning and polishing, Pure VICTORY Polishes also has specialty products for: removing scratches, scuffs and swirls enhancing black and silver engines cleaning engines, tires and wheels removing brake dust After cleaning the motorcycle, inspect for damage to the painted surfaces... Repair chips or scratches promptly by applying VICTORY touch-up paint to prevent corrosion... For more information, or for answers to your cleaning and detailing questions, see your VICTORY dealer or write to the Pure VICTORY Polishes Staff at: [email protected] com...

Page 88

Standard Bucket Wash This is the conventional way to wash your motorcycle... We recommend the use of Pure VIC- TORY Bike Wash Concentrate, a concentrated gentle product formulated to clean without diminishing the life of any durable polish... This product does not contain alkalis, acids or abrasives and is formulated to perform as a wetting agent to soften bugs, road grime and soil, and to prevent abrasion from your wash mitt or cloth... This product also decreases drying time without spotting or streaking... 1... Add 1 ounce (about 2 capfuls) to 1 gallon of water... 2... Apply to a cool motorcycle with a wool or microfiber wash mitt... Tip: For best results, work one side of the motorcycle at a time, working from top to bottom... 3... Rinse thoroughly with an open hose, no pressure needed... Create a sheeting action to

Page 89

Cleaning and Storage Washing the Motorcycle Quick Clean-Ups For quick clean-ups between washings, or when water is not available, use Pure VICTORY Spray & Wipe Instant Detailer, a complete spray-and-wipe product designed to clean and polish all surfaces... It works quickly and easily and is silicone-free so it leaves no oily nor white residue... It provides protection from UV rays, acid rain, and dirt... It will remove bugs, road tar, and road grime from your windshield, paint and chrome... This product is safe for all surfaces, including pin striping, custom paint or murals... Its safe for Plexiglas, Lexan, Acrylic or factory-coated windscreens... Its non-streaking, and it provides polish protection and a water-repellent shine... 1... Spray on all surfaces, including the windshield, paint, chrome, wheels and leather to

Page 90

Standard Method of Polishing Paint and Chrome Pure VICTORY Windshield, Paint and Chrome Polish is a unique formula designed to pro- duce a glass-like shine on painted or clear-coated finishes and chrome surfaces... Use it on chrome-plated accessories to prevent surface rust and create a glass-like shine... This product creates a high reflective index point, giving a deep, shiny finish without sili-

Page 91

For the finest leather care, use Pure VICTORY Leather, Vinyl & Rubber Conditioner, a unique, pleasantly scented formula of premium-quality polymers designed to restore luster and softness to vinyl, leather and rubber without making them slippery... This product is a true conditioner, not a coating... It does not close the pores of the surfaces but penetrates, nourishes and softens the material... It protects against ultra violet (UV) rays and cracking, repels water and prolongs the life and like-new appearance of the materials... Applied to rubber, this product creates a water-repellent, like-new appearance... This product can also be used to restore or maintain the factory finish on a VICTORY instrument panel/ dash and rear storage compartment black vinyl surfaces... Regular use increases soil resis- tance... 1... Apply the product on a clean dry surface using a soft cloth... 2... Rub the product into the material... Repeat the treatment if the surface is extremely dry... 3... Wipe dry with a second cloth to remove excess product... Buff lightly with the second

Page 92

Cleaning and Storage If you will not operate the motorcycle for several months, such as during the winter, store the motorcycle to prevent damage to the fuel system and the battery and to protect components from corrosion or deterioration... During storage you might use products that are potentially hazardous; such as fuel stabilizer... When using any of these products, follow the instructions and warnings on the product packaging... This section includes instructions for preparing the motorcycle for storage, maintaining it during storage and removing it from storage...

Page 93

Park and Cover the Motorcycle Park the motorcycle in its storage location... Cover it with a genuine VICTORY motorcycle cover, or a cover made from a durable, breathable material designed for storage... Covering the motorcycle helps protect it from dust and other airborne materials... The cover must be of a breathable material to prevent moisture from building up on the motorcycle which can cause oxidation of metal surfaces...

Page 94

Cleaning and Storage Removal From Storage 1... Remove the cover and unlock the front forks (if locked)... 2... Verify that tire pressure is at specification... 3... Install the battery and perform an electrical inspection... 4... Check the oil level... If the motorcycle was stored in an area subject to wide swings in

Page 95

Warranty Coverage and Exclusions: Limitations of Warranties and Remedies The warranty excludes any failures that are not caused by a defect in material or workmanship... This warranty does not cover accidental damage, normal wear and tear, abuse or improper handling... This warranty also does not cover any VICTORY Motor- cycle that has been altered structurally, modified, neglected, improperly maintained, used for racing, or used for purposes other than for which it was manufactured, or for any damages which occur during trailer transit or as a result of unauthorized service or the use of unauthorized parts... In addition, this warranty does not cover physical damage to paint or finish, stress cracks, tear- ing or puncturing of upholstery material, corrosion, or defects in parts, components or VICTORY Motorcycle due to fire, explo- sions or any other cause beyond VICTORY Motorcycle Division, Polaris Sales Inc... control... This warranty does not cover the use of unauthorized lubricants, chemicals, or fuels that are not compatible with the VICTORY Motorcycle... The exclusive remedy for breach of this warranty shall be, at VICTORY Motorcycle Division, Polaris Sales Inc... exclusive option, repair or replacement of any defective materials, or components or products... THE REMEDIES SET FORTH IN THIS WARRANTY ARE THE ONLY REMEDIES AVAILABLE TO ANY PERSON FOR BREACH OF THIS WARRANTY... VIC- TORY MOTORCYCLES DIVISION OF POLARIS SALES INC... SHALL HAVE NO LIABILITY TO ANY PERSON FOR INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES OF ANY DESCRIPTION, WHETHER ARISING OUT OF EXPRESS OR IMPLIED WARRANTY OR ANY OTHER CONTRACT, NEGLIGENCE, OR OTHER TORT OR OTHER- WISE... THIS EXCLUSION OF CONSEQUENTIAL, INCIDENTAL, AND SPECIAL DAMAGES IS INDEPENDENT FROM AND SHALL SURVIVE ANY FINDING THAT THE EXCLUSIVE REMEDY FAILED OF ITS ESSENTIAL PUR- POSE... Some states do not permit the exclusion or limitation of incidental or consequential damages or implied warranties, so the above limitations or exclusions may not apply to you if inconsistent with controlling state law...

Page 96

How To Obtain Warranty Service If your VICTORY Motorcycle requires warranty service, you must take it to a VICTORY Motorcycle Servicing Dealer... When requesting warranty service you must present your copy of the Warranty Registration form to the dealer... (THE COST OF TRANSPORTATION TO AND FROM THE DEALER IS YOUR RESPONSIBILITY)... VICTORY MOTORCYCLES division of Polaris Sales Inc... suggests that you use your original selling dealer; however, you may use any VICTORY Motorcycle Ser- vicing Dealer to perform warranty service... Please work with your dealer to resolve any warranty issues... Should your dealer require any additional assistance they will con- tact the appropriate person at VICTORY MOTORCYCLES division of Polaris Sales Inc... This warranty also gives you specific legal rights, and you may also have other rights which vary from state to state... If any of the above terms are void because of state or federal law, all other warranty terms will remain in effect...

Page 97

Engine Engine Type VICTORY Freedom 106 / 6 V-Twin Configuration 50 V-Twin 4 Stroke SOHC Displacement 106 Cubic Inch (1731 cc) Cooling System Air & Oil Compression Ratio 9... 4:1 Valve Train 4 Valves per cylinder, Hydraulic Lifters & Self-Adjusting Cam Chains Bore & Stroke 101 x 108 mm Throttle Body Bore 45 mm Electronic Fuel Injection System Closed Loop Lubrication System Wet Sump Spark Plug / Gap NGK DCPR6E / ... 031-... 035 inch (0... 8-0... 9 mm) Exhaust Split dual exhaust with crossover

Page 98

Chassis Front Suspension Type / Travel Telescopic Fork / 5... 1 in... (13 cm) Front Fork Tube Diameter 43 mm Rear Suspension Type / Travel Single Monotube Air Adjustable Shock: 4... 7 in... (12 cm) Swingarm Cast Aluminum with Constant Rate Linkage Front Brakes Dual 300 x 5 mm / Floating Rotor / 4 Piston Calipers Rear Brakes Single 300 x 7 mm / Floating Rotor / 2 Piston Caliper Total Storage Volume 21... 3 gallons (80... 6 liters)

Page 99

Specifications Fuel Recommendation For best performance, use only unleaded gasoline with a 91 pump octane minimum (R+M/2 Method)... DO NOT USE E-85 GASOLINE OR GASOLINE CONTAINING METHANOL... Using E85 or gasoline / methanol blends can result in poor starting and driveability, and may damage critical fuel system components... Gasoline containing up to 10% Ethanol can be used... Gasoline containing up to 15% Methyl Tertiary Butyl Ether (MTBE) can be used...

Page 100

Audio System Overview Audio System Introduction Not all motorcycles are equipped with all components discussed in the audio section of this manual... Components not installed at the factory can be purchased from and installed by your VICTORY dealer... Software Updates Radio system software should be updated annually to ensure the best performance... Please see your authorized VICTORY dealer for this service...

Page 101

Audio System Overview Citizens Band (CB) Radio Controls If equipped, the operators CB radio controls are located on the left handlebar above the audio controls... Operation of these controls is outlined in greater detail on the following pages... 1... Push-to-Talk (PTT): Press and hold the top or bottom of

Page 102

Audio System Operation Audio System Power The ignition key must be in the ACC or ON position to use the audio system... With the key in the ACC or ON position and audio system OFF, the screen will display VICTORY... Tip: To prevent battery drain, do not leave the key in the ACC position for long periods... VICTORY rec-

Page 103

Audio System Operation Selecting Audio Sources Press and release the MODE button until the desired source is active...

Page 104

Audio System Operation Audio Tuning Use the tuner on the left control to select radio stations... Press and release TUNE (+) or TUNE (-) to locate stations in single-step increments... Press and hold TUNE (+) or TUNE (-) to seek or scan for stations depending on mode setting...

Page 105

Audio System Operation Audio Mode Menus Entering Mode Menus Press and hold the MODE button until the system enters the audio system mode menus... Then press and release the MODE button until the desired mode menu displays... To change mode settings, enter the mode menu... Press TUNE (+) or TUNE (-) to change settings... Wait 5 seconds or push VOL (+) or VOL (-) to exit...

Page 106

CB Headset ENT Mode (if equipped) OFF: Only communications are audible in the headsets... Riders can listen to navigation commands and entertainment with the external speakers while reserving the headset for communication... MIX: The audio source volume drops lower than the ICOM volume whenever the voice-operated switch (VOX) is opened... The audio source volume gradually returns to its original level after the VOX is closed... MUTE: The audio source volume is muted when the VOX is opened... The audio source volume gradually returns to its original level after the VOX is closed...

Page 107

connected with an input cable... If using NAV MP3 mode, always pause the GARMIN unit before changing sources... Otherwise, music from the NAV unit will interrupt the new source, interpreting it as navigation com- mands, not music...

Page 108

Weather Band (WX) Weather band channels are broadcast by the National Oceanic and Atmospheric Admin- istration (NOAA)... NOAA operates more than 940 transmitters covering the United States, Puerto Rico, the U... S... Virgin Islands, the U... S... Pacific Territories and adjacent coastal waterways... Press and release the MODE button until the desired source is active... When the WX source is selected, a total of 7 weather band channels are available... Typically, only one weather band channel will be available for a given location... When traveling, if a channel becomes unavailable, search for another active channel... Press TUNE (+) or TUNE (-) to access a channel...

Page 109

CB Radio / ICOM System CB/ICOM Introduction In the U... S... A... , refer to the Federal Commu- nications Commission (FCC) Plain Rules pamphlet accompanying this riders manual for a comprehensive guide of citizens band (CB) radio rules and regulations... Headset Use The use of helmet-mounted headsets may be restricted or prohibited in some areas... Always obey all applicable regulations and laws... The headsets have three separate volume settings: Intercom (ICOM) volume, CB receive volume and entertainment (ENT) volume... See page 104...

Page 110

When squelch is set to OPEN, no filtering occurs... Setting squelch to CLOSED blocks all signals, including strong signals... To set the squelch level, first lower the squelch level until noise or static is audible... Gradually increase the squelch level until the noise or static is gone...

Page 111

CB Radio / ICOM System Local/Distant CB Radio Mode To change mode settings, enter the mode menu... Press TUNE (+) or TUNE (-) to set the CB to local (LO) or distant (DX) mode... Distant: Use this setting for weaker signals... Receiver sensitivity will be increased... Static and noise levels are increased... Local: Use this setting for stronger signals or in high density areas... Receiver sensitivity will be decreased... Static and noise levels are decreased...

Page 112

VOX Break Setting The intercom is opened and closed using a voice-operated switch (VOX)... The volume sensitivity level required to open the inter- com can be adjusted using the VOX sensi- tivity setting... Press and hold ICOM on the upper left control to access the VOX sensitivity set screen... Push COM or ICOM to adjust the sensitiv- ity setting... Tip: Lower settings require less volume to open

Page 113

Use TUNE (+) or TUNE (-) to scroll through this song list... The selected song will be in reverse video on the center line of the display... Press and release the PRE but- ton to select and play the highlighted song, or press and release the MODE button to exit without selecting a new song...

Page 114

iPod Tuning Press TUNE (+) or TUNE (-) once to move one track forward or backward... Press and hold the button to advance fast-forward or fast-reverse... Press the button twice (double click) to bring up the track selection screen, then use the TUNE button to move forward and backward through the playlist... When the desired track is highlighted, press and release the PRE button to select the track... Tip: To exit the

Page 115

XM Ready Legal XM monthly service subscription sold sepa- rately... XM Mini-Tuner and Home Dock required (each sold separately) to receive XM service... It is prohibited to copy, decom- pile, disassemble, reverse engineer, hack, manipulate or otherwise make available any technology or software incorporated in receivers compatible with the XM satellite Radio System... Installation costs and other fees and taxes, including a one-time activa- tion fee may apply... All fees and program- ming subject to change... Channels with frequent explicit language are indicated with an XL... Channel blocking is available for XM radio receivers by calling 1-800- XMRADIO (U... S... residents) and 1-877- GETXMSR (Canadian residents)... Only available in the 48 contiguous United States and Canada... 2007 XM Satellite Radio Inc... All rights reserved...

Page 116

XM Radio Menu Options The XM radio system has unique menus that apply only to this system when the XM radio is the active source... Some settings such as bass, treble, fader, etc... apply to both the audio system and the XM radio system... Menus specific to the XM radio system are: XM Display (Category or Channel Name) XM Category (Rock, Country, Traffic, Sports, All Channels, Talk News, etc... ) XM Tune Mode (Seek/Scan) Tip: XM Tune Mode is unique to the XM radio

Page 117

XM Radio Channels Press TUNE (+) or TUNE (-) on the left control to change the channel... The ALL CHANNELS category must be selected to scroll through every available channel in numerical order... If a specific category (other than ALL CHANNELS) is selected, only channels within that category will be selected with the TUNE button... Tip: If a preset button is used to tune a station

Page 118

NAV MP3 Navigation MP3 Introduction Please read this manual and the GARMIN ZUMO 660 NAV MP3 information pro- vided with your player to become familiar with all unit features and operation... The audio integration kit must be installed to enable outputs from the NAV MP3 (such as navigation instructions or user-loaded MP3 media files) to play through the head- sets or speakers... The unit is fully functional without the kit installed, but there will be no interface with the vehicles audio system...

Page 119

C Cargo Distribution ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 11 Cargo Safety ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 11 CB Channels ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 107 CB Headset ENT Mode ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 104 CB Headset Volume Controls ... ... ... ... ... ... ... ... ... ... ... ... ... ... 104 CB Radio ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 107 CB Radio Frequencies ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 109 CB Radio Mode, Local/Distant ... ... ... ... ... ... ... ... ... ... ... ... ... 109 CB Radio Volume, Driver ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 108 CB Radio Volume, Passenger... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 108 Check Engine Indicator ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 23, 26 Citizens Band (CB) Radio ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 99 Cleaning Products ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 85 Clock, Resetting ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 22, 27 Clutch Cable Lubrication, Mechanical ... ... ... ... ... ... ... ... ... 70 Clutch Inspection, Mechanical ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 41 Clutch Lever ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 32 Clutch Lever Freeplay, Mechanical ... ... ... ... ... ... ... ... ... ... ... 69 Clutch Lever Lubrication, Mechanical ... ... ... ... ... ... ... ... ... 70 Compliance, Vehicle... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 13 Component Locations

Page 120

I Identification Number Record ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 97 Idle Inspection ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 67 Ignition Key Number... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 16 Ignition Switch ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 19 Ignition Switch Lubrication... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 76 Indicator Lamps... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 20, 25 Information Labels ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 15 Instrument Cluster (CROSS COUNTRY)... ... ... ... 24-28 Instrument Cluster (CROSS ROADS) ... ... ... ... ... ... 20-23 Intercom System ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 107, 110 iPod Playlists ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 112 iPod Song Control ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 111 iPod Tuning ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 112

Page 121

S Shift Points ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 48 Shifting Gears ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 47-48 Side Covers, Removal/Installation ... ... ... ... ... ... ... ... ... ... ... ... 77 Sidestand... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 34 Sidestand Inspection ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 43 Sidestand Lubrication ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 77 Signal Words ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 5 Spark Plugs ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 74 Speedometer ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 20, 24 Squelch ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 108 Starter Interlock Switch ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 30 Steering Head Inspection ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 66 Steering Inspection ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 42 Storage

Page 122

Tachometer ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 24 Testing After Servicing ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 54, 82 Throttle Cable Freeplay ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 68 Throttle Cable Lubrication ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 69 Throttle Control Grip... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 32 Throttle Control Inspection ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 68 Throttle Freeplay ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 41 Throttle Inpspection... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 41 Tilt Sensor ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 32 Tires ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 39, 73-74

Manualsnet FAQs

If you want to find out how the Victory Cross Roads Polaris works, you can view and download the Polaris Victory Cross Roads, Cross Country Rider's Manual on the Manualsnet website.

Yes, we have the Rider's Manual for Polaris Victory Cross Roads as well as other Polaris manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Rider's Manual should include all the details that are needed to use a Polaris Victory Cross Roads. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Polaris Victory Cross Roads, Cross Country Rider's Manual is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Polaris Victory Cross Roads, Cross Country Rider's Manual consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Polaris Victory Cross Roads, Cross Country Rider's Manual free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Polaris Victory Cross Roads, Cross Country Rider's Manual, simply download the document to your computer. Once downloaded, open the PDF file and print the Polaris Victory Cross Roads, Cross Country Rider's Manual as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.