Polaris S,8Ball,Jackpot,HighBall,JudgeGunner Rider's Manual PDF

Pages 106
Year 2016
Language(s)
English en
1 of 106
1 of 106

Summary of Content for Polaris S,8Ball,Jackpot,HighBall,JudgeGunner Rider's Manual PDF

Page 4

Copyright 2015 Polaris Industries Inc... All material in this publication is based on the latest product information at the time of publication... Due to constant improvements in the design and quality of production components, some minor discrepancies may result between the actual vehicle and the information presented in this publication... Depictions and/or procedures in this publication are intended for reference use only... No liability can be accepted for omissions or inaccuracies... VICTORY MOTORCYLES reserves the right to make changes at any time, without notice and without incurring obligation to make the same or similar changes to previously manufactured vehicles... Any reprinting, reuse or redistribution of the material in this document is expressly prohibited... Features of VICTORY motorcycles are covered by U... S... Patents: 6,976,691; 6,407,663; D489670; D482311; D482304; D481980; D481973; D474142... Refer also to the patent label on the motorcycle... The following are trademarks of Polaris Industries Inc... : VICTORY, VICTORY MOTORCYCLES, POLARIS, FREEDOM, HAMMER, VEGAS, VEGAS 8-BALL, HIGH-BALL and VICTORY GUNNER... DUNLOP is a registered trademark of Dunlop Tire Corporation... Printed in U... S... A... P/N 9926232

Page 5

Safety Training Safety training is a top priority for POLARIS... POLARIS strongly encourages you to take a rider education course from the Motorcycle Safety Foundation or another qualified instructor... The course will help you develop or refresh your expertise in safe riding habits through instruction and riding... For information on Motorcycle Safety Foundation rider education courses in your area, call 1-800- 446-9227 or visit their home page at www... msf-usa... org...

Page 7

Table of Contents Introduction ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 6 Safety ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 7 Reporting Safety Defects ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 20 Component Identification ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 22 Instruments, Features and Controls ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 25 Pre-Ride Inspections ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 34 Operation ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 45 Maintenance... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 51 Cleaning and Storage... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 78 Warranties ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 86 Specifications ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 94 Identification Numbers ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 98 Maintenance Record ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 99 Index ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 101

Page 8

For the safe and enjoyable operation of your vehicle, be sure to follow the instructions and recommendations in this riders manual... Keep this manual with the motorcycle, especially when ownership changes... If your riders manual is misplaced or damaged, please purchase a replacement from your VICTORY dealer... All references in this manual to RIGHT, LEFT, FRONT or REAR are from the operators perspective when seated in a normal riding position... If you have questions about the operation or maintenance of your motorcycle after you've read this manual, please see your VICTORY dealer... To locate the nearest authorized VICTORY dealer, call 1-877-737-7172 or visit www... victorymotorcycles... com... VICTORY motorcycles comply with all federal, state and local safety and emission regulations for the area of intended sale...

Page 9

This riders manual contains information that is essential to safe riding and proper maintenance of your VICTORY motorcycle... Anyone who uses the motorcycle (operators and passengers) must read the riders manual before riding... Carefully read and understand the information found in the Safety section... Understand and follow the procedures outlined in the Maintenance section to keep your VICTORY motorcycle in top condition on the road or in storage... Bring the manual with you when you ride... Following the precautions and procedures in the manual will add to your enjoyment and help keep you riding safely... If you lose or damage this manual, you can purchase a new one through any authorized VICTORY dealer... The riders manual should be considered part of the motorcycle and remain with it if sold...

Page 10

Safety Safety Terms and Signal Words The following signal words and symbols appear throughout this manual and on your vehicle... Your safety and the safety of others is involved when these words and symbols are used... Become familiar with their meanings before reading the manual...

Page 11

Improper use of this motorcycle can result in serious injury or death to you, your passenger and others... To minimize the risk of injury, read and understand the information contained in this section before operating the motorcycle... This section contains safety information specific to the VICTORY motorcycle, as well as information about general motorcycle safety... Anyone who rides the motorcycle (operators and passengers) must follow these safety precautions...

Page 12

Ride defensively, as if you are invisible to other motorists, even in broad daylight... A motorist's failure to see or recognize a motorcycle is the leading cause of automobile/ motorcycle accidents... Ride where you're clearly visible to other motorists, and observe their behavior carefully...

Page 13

the road has potholes, or is otherwise rough or uneven... the road contains sand, dirt, gravel or other loose substances... the road is wet, icy or oily... the road contains painted surfaces, manhole covers, metal grating, railway crossings or other

Page 14

Safety Safe Riding Practices Carrying a Passenger Do not carry a passenger unless the motorcycle is equipped with passenger seat and passenger footrests... To carry a passenger safely: Do not exceed the gross vehicle weight rating (GVWR)... See the manufacturers label (on

Page 15

Wear gloves, a jacket, heavy boots and long pants to prevent or reduce injury from abrasions, lacerations or burns should the motorcycle fall... Wear boots with low heels, as high heels can catch on pedals or footrests... The combination of boots and pants should completely cover legs, ankles and feet, protecting skin from engine and exhaust system heat...

Page 16

Safety Gross Vehicle Weight Rating (GVWR) WARNING! Exceeding the gross vehicle weight rating of your motorcycle can reduce stability and handling and could cause loss of control... NEVER exceed the GVWR of your motorcycle... The maximum load capacity of your motorcycle is the maximum weight you may add to your motorcycle without exceeding the GVWR... This capacity is determined by calculating the difference between your motorcycles GVWR and wet weight... Refer to the specification section beginning on page 94 or the Manufacturing Information/ VIN label on the motorcycle frame for model-specific information... See page 21... When determining the weight you will be adding to your motorcycle, and to ensure you do not exceed the maximum load capacity, include the following: operator body weight passenger body weight weight of all riders apparel and items in or on apparel weight of any accessories and their contents weight of any additional cargo on the motorcycle

Page 17

Parking the Motorcycle When leaving the motorcycle unattended, turn the engine off... Remove the ignition key to prevent unauthorized use by minors or those without proper motorcycle certification and training... Park the motorcycle where people are not likely to touch the hot engine or exhaust system or place combustible materials near these hot areas... Do not park near a flammable source such as a kerosene heater or an open flame, where hot components could ignite combustible materials... Park the motorcycle on a firm, level surface... Sloped or soft surfaces may not support the motorcycle... If you must park on a slope or soft surface, follow the precautions outlined on page 50...

Page 18

them upward... Place tiedown straps around the fork tubes above the lower triple clamp... Secure the rear of the motorcycle with tiedowns around both sides of the swingarm, being careful to avoid the brake line, exhaust and drive belt... Reposition the turn signals before operating the motorcycle...

Page 19

Safety Use of Accessories Because VICTORY cannot test and make specific recommendations concerning every accessory or combination of accessories sold, the operator is responsible for determining that the motorcycle can be safely operated with any accessories or additional weight... Use the following guidelines when choosing and installing accessories: Do not install accessories that impair the stability, handling or operation of the motorcycle

Page 20

Gasoline is highly flammable and explosive under certain conditions... Always exercise extreme caution whenever handling gasoline... Always turn off the engine before refueling... Always refuel outdoors or in a well-ventilated area... Open the fuel cap slowly... Do not overfill the tank... Do not fill the tank neck... Do not smoke or allow open flames or sparks in or near the area where refueling is performed or

Page 21

Failure to perform safety maintenance as recommended can result in difficult handling and loss of control, which could result in serious injury or death... Always perform the safety maintenance procedures as recommended in this manual... Perform maintenance and repairs promptly as outlined in the VICTORY Service Manual, or see your authorized VICTORY dealer for service...

Page 22

Reporting Safety Defects If you believe that your vehicle has a defect that could result in a crash or cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying Polaris Industries in writing... If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign... However, NHTSA cannot become involved in individual problems between you, your dealer or Polaris Industries... To contact NHTSA, or obtain other information about motor vehicle safety, you may call the Vehicle Safety Hotline toll free at 1-888-327-4236 (TTY: 1-800-424-9153), visit the NHTSA web site at www... safercar... gov, or write to:

Page 23

Safety Safety and Information Labels Due to different model and market requirements, your vehicle may not have all of the labels shown... Labels that apply to your model will be located as shown...

Page 24

Left Side View 1... Front Turn Signal 2... Headlamp 3... Air Filter 4... Spark Plugs 5... Ignition Switch 6... Battery (under side cover) 7... Taillight 8... Rear Turn Signal 9... Rear Axle Adjuster (each side) 10... Rear Brake Caliper 11... Passenger's Foot Rest 12... Evaporative Emissions Canister

Page 25

(under cover) 3... Diagnostic Connector 4... Fuses 5... Rear Shock Access 6... Front Turn Signal 7... Front Brake Caliper 8... Rear Brake Pedal 9... Operator's Foot Rest 10... Engine Oil Fill Cap/Dipstick 11... Drive Sprocket (under cover) 12... Passenger's Foot Rest 13... Drive Belt (under guard) 14... Exhaust Mufflers

Page 26

Ignition Switch The ignition switch provides electrical power to the ignition, the lighting system and all electrical switches and buttons... The ignition key operates the ignition switch and parking lights... OFF All electrical circuits are inactive and the ignition key can be removed... ON All electrical circuits are energized and the ignition key cannot be removed... The headlamp, taillight, and instrument lights illuminate... PARK (P) The taillight, indicator lights, and license plate light illuminate... The emergency flashers can be activated, and the ignition key can be removed... Push the ignition key inward while selecting the PARK position...

Page 27

Check Engine This lamp illuminates momentarily when the ignition switch is in the ON position and the engine is off... This indicates proper function... If this lamp illuminates while the engine is running, contact an authorized VICTORY dealer promptly for diagnosis... The light will remain on if the tilt sensor shuts down the engine... See page 47... If abnormal sensor or engine operation is detected the light will remain on as long as the fault condition exists... Retrieve the error codes for diagnosis... See page 29... This lamp is also known as a malfunction indicator lamp (MIL)...

Page 28

Instruments, Features and Controls Instrument Cluster Multi-Function Display Use the mode button to toggle through the modes of the multi-function display... Press and hold the mode button to reset the trip odometers, average fuel economy, average speed and trip hour meter...

Page 29

Instruments, Features and Controls Instrument Cluster Multi-Function Display Odometer The odometer displays total distance traveled by the vehicle... Trip Odometers The ignition switch must be in the ON position to access the trip odometers... The trip odometers (Trip 1 and Trip 2) display total distance traveled since being reset... To reset a trip odometer, toggle to the trip odometer... Press and hold the mode button until the meter resets... Engine Speed (Tachometer) Engine speed displays in revolutions per minute (RPM)... Gear Position A gear position displays only when the transmission is in gear and the motorcycle is moving... Two dashes (--) display if the stop/run switch is in the RUN position and the motorcycle is not moving while in gear... The dashes also display if the stop/run switch is in the STOP position... N displays when the stop/run switch is in the RUN position and the transmission is in neutral... Clock Tip: The clock must be reset any time the battery has been disconnected or discharged... 1... Turn the key to the ON position... Use the mode button to toggle to the odometer display... 2... Press and hold the mode button until the hour segment flashes... Release the button... 3... With the segment flashing, tap the mode button to advance to the desired setting... 4... Press and hold the mode button until the next segment flashes... Release the button... 5... Repeat steps 3-4 twice to set the 10-minute and 1-minute segments... After completing the

Page 30

Instruments, Features and Controls Instrument Cluster Multi-Function Display Average Speed (Accessory) The average speed mode displays average vehicle speed since being reset... To reset, toggle to this mode... Press and hold the mode button until the meter resets... DC Voltage (Accessory) The volt meter displays battery voltage... If the engine is not running, approximate battery voltage displays... If the engine is running, approximate charging voltage displays... Ambient Air Temperature (Accessory) If the accessory sensor is installed, toggle to this mode to display the ambient air temperature... The key must be in the ON position... Diagnostic Functionality Certain conditions will cause an error message to display in the screen... If this occurs, please see your VICTORY dealer...

Page 31

Instruments, Features and Controls Instrument Cluster Multi-Function Display Engine Error Codes The error screen displays only when the CHECK ENGINE light is on or when it goes on and off during one ignition cycle... Error codes are not stored... When the key is turned OFF, the code and message is lost, but will reappear if the fault reoccurs after restarting the engine... If the CHECK ENGINE indicator lamp illuminates, retrieve the error codes from the display... 1... If the error codes are not displayed, use the

Page 32

Turn Signal Switch Move the turn signal switch to the left to activate the left turn signals... Move the switch to the right to activate the right turn signals... A signal ends when speed or distance reach preset levels... To end a signal manually, move the switch to the center and push it inward... Momentary Feature: Move the turn signal switch left or right and hold it in that position... The signal flashes until the switch is released...

Page 33

Throttle Control Grip Twist the throttle control grip toward your body to increase engine speed... Twist the grip away from your body to decrease engine speed... When you release the grip, it returns to the idle speed position... Front Brake Lever Pull the lever toward the handlebar to apply the front brake... Always follow proper braking procedures... See page 49... To maximize braking effectiveness, use the front and rear brakes together...

Page 34

Close the fuel cap 1... Insert the key into the cap... Turn the key clockwise and press downward on the cap... 2... Turn the key counter-clockwise while pushing downward lightly... 3... Remove the key and close the key slot cover...

Page 35

Instruments, Features and Controls Sidestand WARNING! An improperly retracted sidestand could contact the ground during operation and cause loss of control resulting in serious injury or death... Always make sure the sidestand is fully retracted before operating the motorcycle... 1... While the motorcycle is in the upright position, push the sidestand downward until it is

Page 36

Failure to perform the recommended pre-ride inspections could result in component failure while riding, which could result in serious injury or death... Always perform the pre-ride inspections before each ride... Tip: You must be familiar with all instruments and controls to perform the pre-ride inspections... During the pre-ride inspections you may use products that are potentially hazardous, such as oil or brake fluid... When using any of these products, always follow the instructions and warnings on the product packaging... When inspections reveal the need for adjustment, replacement or repair: refer to the maintenance section of this manual (page 51) refer to the VICTORY Service Manual or see your authorized VICTORY dealer

Page 37

Pre-Ride Inspections Electrical Components Move the ignition switch to the ON position before performing the electrical inspections outlined on this page... Return the ignition switch to the OFF position after completing these inspections... If inspection of any electrical item reveals component failure, repair or replace the component before operating the motorcycle...

Page 38

Pre-Ride Inspections Engine Oil Level Polaris recommends the use of only VICTORY Semi-Synthetic 20W-40 oil, Synthetic 15W- 60 oil or an equivalent oil designed for use with wet clutches (such as those with a JASO MA rating)... The oil fill cap/dipstick is located on the right side of the vehicle... NOTICE: Operating the engine with too much or

Page 39

Pre-Ride Inspections Fuel Level 1... On level ground, straddle the motorcycle and bring it to the fully upright position... 2... Start the engine... The low fuel indicator light will stay on if the fuel tank level is less than

Page 40

Tire Condition Inspect the tire sidewalls, road contact surface and tread base... If inspection reveals cuts, punctures, cracks or other wear or damage, replace the tire before riding... Use only approved replacement tires... See the VICTORY Service Manual or your authorized VICTORY dealer...

Page 41

Pre-Ride Inspections Front Brake Lever Pull the front brake lever toward the handlebar and release it... It should move freely and smoothly, and it should return to its rest position quickly when released... You should feel a firm resistance in the lever within the first 3/4 inch (19 mm) of lever travel... If the lever fails to perform as stated, service the brake lever before riding... See the VICTORY Service Manual or your authorized VICTORY dealer...

Page 42

Pre-Ride Inspections Rear Brake Pedal Press and release the rear brake pedal... It should move freely and smoothly, and it should return to its rest position quickly when released... You should feel a firm resistance in the pedal within the first 3/8 inch (8 mm) of pedal travel... If the brake pedal fails to perform as stated or travels too far before beginning to engage the brake, see the VICTORY Service Manual, or contact an authorized VICTORY dealer for service... Change the brake fluid at the intervals recommended in the periodic maintenance table beginning on page 52 or every two years, whichever comes first...

Page 43

Throttle Freeplay Throttle freeplay is the amount of throttle control grip movement from the rest position to the point of cable resistance... Measure this distance... Freeplay should be 2-4 mm... Adjust throttle freeplay as needed... See page 64...

Page 44

2... Freeplay (gap) is the amount of lever movement from the rest position to the point of cable resistance... Clutch lever freeplay should be 0... 5-1... 5 mm... Measure the gap between the clutch lever and the lever housing... Adjust clutch lever freeplay if necessary... See page 65...

Page 45

Rear Suspension Proper rear suspension adjustment is essential for a safe and comfortable ride... Check rear shock absorber movement and preload to ensure the correct amount of suspension travel and ground clearance... See page 59... WARNING! Inadequate ground clearance could result in components contacting the ground, causing loss of control resulting in serious injury or death... Always ensure ground clearance is at specification...

Page 46

2... Move the sidestand upward to the stored position and downward to the fully extended position several times... It should move smoothly and quietly... Make sure the return spring holds the sidestand tightly in place when the sidestand is in the stored position...

Page 47

Follow all safe riding practices outlined in the safety section... See page 7... During the first 500 miles (800 km), critical engine parts require special wear-in procedures so they seat and mate properly... Read, understand and use the following rules for operating the motorcycle during the first 500 miles (800 km)... NOTICE: Do not put unnecessary load on the engine during the first 500 miles (800 km)... Avoid

Page 48

Operation Engine Break-in Period Fueling and Fill Height Always heed fuel warnings... See page 18... Always refuel on level ground with the sidestand down... Use only the recommended fuel... See page 98... Fill the fuel tank to a level just below the bottom of the fuel filler insert... WARNING! Overflows or spilled gasoline could contact a hot engine or exhaust system and cause a fire, which could result in serious injury or death... Do not allow gasoline to contact hot components... Fuel expands in the fuel tank... Do not overfill... To prevent leaks, make sure the fuel filler cap is properly seated and locked... NOTICE: Fuel can damage painted surfaces and plastic parts... If gasoline spills on the any part of the

Page 49

page 46... 1... Perform the pre-ride inspections... See page 34... 2... Insert the key into the ignition switch and turn the switch to the ON position... 3... Straddle the motorcycle and bring it to the fully upright position... 4... Engage the front brake and place the sidestand in the stored (up) position... 5... If the neutral indicator is not illuminated, shift the transmission to neutral... 6... Move the engine stop/run switch to the RUN position... You should hear the fuel pump

Page 50

Operation Shifting Gears WARNING! Forced shifting (with clutch engaged) could cause damage to the engine, transmission and drive train... Such damage could cause loss of control, which could result in serious injury or death... Always pull the clutch lever fully toward the handlebars to disengage the clutch before shifting gears... On motorcycles equipped with a six-speed transmission, the sixth gear is overdrive... Neutral is located between first and second gear... Tip: The transmission is in neutral if you can move the

Page 51

Operation Accelerating Accelerate by opening the throttle (rolling the throttle control grip rearward)... The more quickly you open the throttle, the more quickly the motorcycle accelerates... For even acceleration, open the throttle with a smooth, continuous motion... When you reach the recommended speed for upshifting, shift up one gear... See page 47... WARNING! Accelerating abruptly could cause your body to shift rearward suddenly, which could result in loss of control... Accelerating abruptly could also cause loss of control on low traction surfaces... Loss of control could result in serious injury or death... Always accelerate gradually, especially on wet, slippery or other low traction surfaces...

Page 52

Parking on a Soft Surface If parking on a soft surface is unavoidable, place a sidestand footrest under the foot of the sidestand to provide a firm surface... The sidestand footrest must be strong enough and large enough to support the motorcycle's weight without sinking into the parking surface... Asphalt becomes soft in hot weather... A sidestand can sink into soft asphalt and the motorcycle may fall... When parking on asphalt in hot weather, use a sidestand footrest... CAUTION! Hot engine and exhaust components can cause burns to skin and can ignite a fire if exposed to flammable materials... Always park the motorcycle clear of flammable materials and where people are not likely to contact hot components...

Page 53

Periodic Maintenance Always position the motorcycle on a firm level surface before performing service... Inspect, clean, lubricate, adjust and replace parts as necessary... When inspection reveals the need for replacement parts, use genuine VICTORY parts available from your VICTORY dealer... Record service and maintenance information in the Maintenance Record... See page 99... Perform maintenance at the intervals specified in the periodic maintenance table... See page 52... Perform the procedures more frequently if normal use of the motorcycle includes: high speed operation for extended periods low speed operation for extended periods operation in dusty or otherwise adverse conditions Before beginning any maintenance procedure, read the instructions for the entire procedure... During some procedures you may use potentially hazardous products such as oil or brake fluid... Always follow the instructions and warnings on the product packaging... WARNING! Improperly installed or adjusted components can make the motorcycle unstable or hard to handle... Improperly installed electrical components can cause engine or electrical system failure... In either event, damage or serious injury could result... If you do not have the time, tools and expertise necessary to complete a procedure properly, please see your dealer for service...

Page 54

* Replace at specified interval, or annually ** Replace at specified interval, or every 2 years *** Replace every 5000 mi... (8000 km) if operating in

Page 55

Engine Oil and Filter Change 1... Start the engine and allow it to idle for several minutes... Stop the engine... Tip: The engine must be at normal operating temperature before changing the oil... CAUTION! Hot engine and exhaust components can cause burns to skin and can ignite a fire if exposed to flammable materials... Always park the motorcycle clear of flammable materials and where people are not likely to contact hot components... 2... Position the motorcycle securely on the sidestand... 3... Place a drain pan under the drain plug and oil filter... 4... Remove the drain plug and seal... Use the universal tool (under the left side cover) or a

Page 56

Drive Belt Condition Replace the drive belt if it is cracked or has broken teeth or frayed edges... No matter its condition, the drive belt should be replaced at periodic intervals... See the VICTORY Service Manual or your authorized VICTORY dealer... DO NOT attempt to check belt tension if the belt has been exposed to rain or washing within a 24 hour period or if the belt is hot from riding... Allow the belt to cool down to ambient temperature before measuring belt tension... To obtain the maximum drive belt service life possible, VICTORY recommends the replacement of both sprockets as a set if the drive belt system has over 5,000 miles (8,000 km) of service at the time of damage or failure...

Page 57

Drive Belt Deflection - with 10 lbs... (4... 5 kg) of force New drive systems (new belt/sprockets) 5 mm +/- 0... 5 mm After 500 miles on drive system 6 mm +/- 0... 5 mm

Page 58

6... Push the plunger upward until the small O-ring touches the tension gauge body... Make sure the tension gauge is seated squarely against the drive belt, and record the position of the base of the tension gauge bracket... This position represents 10 lbs... (4... 5 kg) of force...

Page 59

Drive Belt Cleaning Cleaning the drive belt will maximize belt and sprocket life and minimize drive line noise... Clean the belt at every tire change... Clean the belt more often if riding in dirty, dusty or high debris environments... 1... Mix a few drops of mild dish soap with a cup of warm water... 2... Use a soft nylon brush to clean the belt and sprocket teeth with the soapy water... Clean

Page 60

Maintenance Rear Wheel Alignment WARNING! A skewed rear axle can damage the drive belt, causing belt failure and loss of control of the motorcycle... 1... Elevate and support the rear of the motorcycle with the wheel slightly above the ground...

Page 61

Maintenance Rear Suspension Rear Shock Preload (Ride Height) Inspection Set preload with accurate load conditions before riding to ensure optimum handling, safety and ride quality... A shock absorber preload wrench (PV-43507) is designed specifically for adjusting the preload on your motorcycle... The tool is available from your dealer... Have an assistant help with this procedure... 1... Verify that tire pressure is at specification... See page 69... 2... Load the motorcycle with all intended cargo... Wearing your riding gear, bring the

Page 62

10... Recheck the preload measurement after adjusting... 11... Tighten the lock nut securely against the adjuster nut... 12... Reinstall the fuse box bracket and tighten the bolts securely... 13... Reinstall the fuse box and side cover...

Page 63

5... Fork oil condition and level affects front suspension performance and internal component wear... Replace fork oil at the recommended intervals... Special tools are required to perform this procedure... See the VICTORY Service Manual or your authorized VICTORY dealer...

Page 64

attempt to move the wheel front-to-back... If there is front-to-back movement at the steering head, the steering head bearings should be inspected, lubricated and adjusted... Lubricate the steering head bearings at the recommended intervals even if there is no front-to-back movement at the steering head... See the VICTORY Service Manual or your authorized VICTORY dealer...

Page 65

5... Lift the fuel tank and unplug the fuel pump wire harness at the rear of the tank... 6... Disconnect the fuel line from the fuel pump using the same procedure used in step 4... 7... At the rear left side of the tank, disconnect the tank vent hose and the water drain hose... 8... Carefully remove the fuel tank... Be prepared to catch dripping fuel in an appropriate

Page 66

performance... Verify proper routing and smooth movement... Inspect for damage to the external casing, and inspect exposed cable wire for fraying, kinks or corrosion... Replace any damaged, sticky or sluggish cable... 1... Disconnect the cable at the throttle body... 2... Apply a light film of VICTORY All Purpose Grease or equivalent to the barrel end... 3... Reconnect the cable and adjust freeplay as needed...

Page 67

lubrication could be detrimental to cable performance... Verify proper routing and smooth movement... Inspect for damage to the external casing, and inspect exposed cable wire for fraying, kinks or corrosion... Replace any damaged, sticky or sluggish cable... 1... Disconnect the cable at the clutch lever and at the primary cover... 2... Lubricate both barrel ends with VICTORY All Purpose Grease or equivalent... 3... Reconnect the cable and adjust freeplay as needed...

Page 68

Maintenance Gear Shift Pedal Do not remove and reposition the shift arm on the shift shaft to adjust gear shift pedal height... A 90+/-5 angle between the shift arm and the linkage rod is necessary to ensure correct shift linkage operation... 1... Loosen the gear shift linkage rod

Page 69

Rear Brake Fluid Check the rear brake fluid level... See page 41... The fluid level should be between the minimum and maximum marks on the reservoir... Add fluid as needed... Replace cloudy or contaminated fluid... Use DOT4 brake fluid in the brake fluid reservoir... Use fluid only from a sealed, clean container... Do not operate the brake while the reservoir cover is removed... Fluid could overflow from the reservoir and cause air to enter the fluid system... WARNING! Using the wrong fluid or allowing air or contaminants into the fluid system can damage the system seals or result in a malfunction that could lead to serious injury or death... 1... Secure the motorcycle in a vertical position with an appropriate motorcycle lift... 2... Remove the right side cover... 3... Wipe the fluid container and the area around the reservoir cover with a clean cloth... NOTICE: Brake fluid will damage painted surfaces and plastic parts... Always clean spilled brake fluid

Page 70

Brake Discs Inspect brake discs for nicks, scratches, cracks or other damage... Inspect the thickness of each brake disc at four or more locations around the disc... Minimum thickness is stamped on the inner hub of the disc... If any disc is worn to the minimum thickness at the thinnest point, or if a disc is damaged, see your VICTORY dealer for replacement...

Page 71

Tire Tread Depth The raised areas at the base of the tread are wear bars... When the road contact surface has worn to the top of the wear bars, replace the tire... For more precise measurement, and for tires not equipped with wear bars, use a depth gauge or an accurate ruler to measure the depth of the center tire tread... Replace the tire if the tread depth is less than 1/16 inch (1... 6 mm)...

Page 72

Maintenance Wheel Spokes Inspect both wheels for loose, bent, broken or missing spokes (if equipped)... To identify loose spokes, grasp each spoke and try to move it side to side or up and down... All spokes should be equally tight and have the same amount of flex... Tighten loose spokes and replace bent, broken or missing spokes (see an authorized VICTORY dealer)... WARNING! Spokes adjusted or replaced improperly could distort the wheel, make the motorcycle difficult to handle, and cause loss of control...

Page 73

5... If spark plugs are in good condition and are not due for replacement, clean them with a non-metallic stiff bristle brush, set the gap with a spark plug gap tool, clean the mating surface on the cylinder head, and install the spark plug with a spark plug socket... Reinstall both spark plug wires...

Page 74

Maintenance Seat Removal (VEGAS/VEGAS 8-BALL/HIGH-BALL/GUNNER) WARNING! A loose seat could cause a sudden shift in riding position, causing loss of control... Always make sure the seats are securely fastened before riding the motorcycle... 1... Remove the side covers... Remove the fuse box from the bracket... 2... Remove the two screws (left and right) securing the seat to the frame... 3... Lift the rear of the seat and pull rearward and upward to remove it...

Page 75

Maintenance Handlebar Position (HIGH-BALL) On models equipped with two handlebar positions, the motorcycle is manufactured with handlebars in the low position... Before changing handlebar position, check regulations in your area of operation... Operation with the handlebars in the high position may not be legal in all areas or for all riders... WARNING! Handlebar controls must be repositioned each time handlebar position is changed... Failure to reposition handlebar controls could result in loss of vehicle control resulting in severe injury or death... 1... To adjust handlebar position, loosen

Page 76

Battery electrolyte is poisonous... It contains sulfuric acid... Serious burns can result from contact with skin, eyes or clothing... Antidote: External: Flush with water... Internal: Drink large quantities of water or milk... Follow with milk of magnesia, beaten egg, or vegetable oil... Call physician immediately... Eyes: Flush with water for 15 minutes and get prompt medical attention... Batteries may produce explosive gases... Keep sparks, flame, cigarettes, etc... away... Ventilate when charging or using in an enclosed space... Always shield eyes when working near batteries KEEP OUT OF REACH OF CHILDREN...

Page 77

Fuse Recommendations Engine / ECM 15 amp Fuel Pump 10 amp Headlamp / Brake Lamp 20 amp Tail Lamp, Flashers, Indicator Lamp, Horn 15 amp Ignition / Gauges 15 amp Accessory Fuse (for emergency use) (motorcycle will operate without fuse)

Page 78

Maintenance Headlight Aim Inspection The top edge of the high beam must be 3 inches (7... 6 cm) below the height of the headlight housing parting line and centered straight ahead at 25 feet (7... 6 m)... 1... Verify that tire pressure is at specification...

Page 79

Maintenance Headlight Lamp Replacement High intensity discharge (HID) lamps, if equipped, should be handled only by a trained technician wearing the appropriate protective gear... See the VICTORY Service Manual or an authorized VICTORY dealer...

Page 80

Cleaning and Storage VICTORY Cleaning Products This section provides tips on the very best way to clean, polish and preserve every surface of your beautiful new VICTORY motorcycle... We recommend the use of our VICTORY cleaning and polishing products and accessories, which have been specially designed to offer the best care possible for your VICTORY motorcycle... In addition to the products recommended in this section for cleaning and polishing, VICTORY also has specialty products for: removing scratches, scuffs and swirls enhancing black and silver engines cleaning engines, tires and wheels removing brake dust After cleaning the motorcycle, inspect for damage to the painted surfaces... Chips or scratches should be repaired promptly to prevent corrosion... For Suede Paint (Matte Clear Coat) Finish Care, see page 79... For Gloss Clear Coat Finish Care, see page 80... For more information, or for answers to your cleaning and detailing questions, please see your VICTORY dealer...

Page 81

Suede Paint (Matte Clear Coat) Finish Care Suede paint finishes are prone to trapping dirt, oils and other contaminants... Always clean this type of finish with warm water and a mild dish-washing detergent... Use a soft sponge to gently rub the surface, then rinse with clean warm water... For stubborn stains such as grease or oil, use a citrus-based cleaner... Spray the cleaner onto the area and rub gently with a soft sponge... Allow the cleaner to sit for a couple of minutes, then rinse well with clean warm water... Repeat as needed... Apply VICTORY Suede Finish Protectant... Follow the instructions on the container... NOTICE: Never use a polishing/buffing wax or any sponge that has an abrasive surface when

Page 82

Cleaning and Storage Gloss Clear Coat Finish Care The Axalta Sports and Equipment Finish System was used to provide the original gloss finish on your motorcycle... This finish system provides superior protection against the elements... To maximize the benefits of this system, use the following guide to care for the gloss finish on your motorcycle... During the first 30 days, when the finish is still fresh, clean the motorcycle with a water

Page 83

Cleaning and Storage Polished Aluminum Care When a VICTORY motorcycle is new, the polished aluminum wheels, hand levers and shifter shine like chrome... Ultraviolet (UV) rays and oxidation will cause polished aluminum to grow dull, however, if its not properly polished and protected... VICTORY Awesome Metal Polish will clean, polish and protect these aluminum surfaces... This metal polish will restore that factory chrome-like shine and leave a protective coating that resists future oxidation for several months... 1... Shake the polish container well before using... 2... Apply the product with a terry cotton or microfiber cloth or pad... 3... Rub gently until the black begins to come to the surface or until shine begins to show

Page 84

For the finest leather care, use VICTORY Leather, Vinyl & Rubber Conditioner, a unique, pleasantly scented formula of premium-quality polymers designed to restore luster and soft- ness to vinyl, leather and rubber without making them slippery... This conditioner is available in the VICTORY Travel Kit... This product is a true conditioner, not a coating... It does not close the pores of the surfaces but penetrates, nourishes and softens the material... It protects against ultra violet (UV) rays and cracking, repels water and prolongs the life and like-new appearance of the materials... Applied to rubber, this product creates a water-repellent, like-new appearance... Regular use increases soil resistance... 1... Apply the product on a clean dry surface using a VICTORY microfiber towel... 2... Rub the product into the material... Repeat the treatment if the surface is extremely dry... 3... Wipe dry with a clean, dry microfiber towel to remove excess product... Buff lightly with

Page 85

Cleaning and Storage If you will not operate the motorcycle for several months, such as during the winter, store the motorcycle to prevent damage to the fuel system and the battery and to protect components from corrosion or deterioration... During storage you might use products that are potentially hazardous; such as fuel stabilizer... When using any of these products, follow the instructions and warnings on the product packaging... This section includes instructions for preparing the motorcycle for storage, maintaining it during storage and removing it from storage...

Page 86

Motorcycle Covers Cover the motorcycle with a genuine VICTORY motorcycle cover or a cover made from a durable, breathable material designed for storage... The cover must be of a breathable material to prevent moisture build-up, which can cause oxidation of metal surfaces...

Page 87

Cleaning and Storage Removal From Storage 1... Remove the cover and any intake or exhaust coverings... 2... Unlock the front forks (if locked)... 3... Verify that tire pressure is at specification... 4... Install the battery and perform an electrical inspection... 5... Check the oil level... If the motorcycle was stored in an area subject to wide swings in

Page 88

Warranty Coverage And Exclusions: Limitations Of Warranties And Remedies This limited warranty excludes any failures that are not caused by a defect in material or workmanship... THIS WARRANTY DOES NOT COVER CLAIMS OF DEFECTIVE DESIGN... This warranty also does not cover acts of God, accidental damage, normal wear and tear, abuse or improper handling... This warranty also does not cover any motorcycle, component, or part that has been altered structurally, modified, neglected, improperly maintained or used for racing, competition or purposes other than for which it was designed... This warranty excludes damages or failures resulting from: improper lubrication; improper engine timing; improper fuel; surface imperfections caused by external stress, heat, cold or contamination; operator error or abuse; improper component alignment, tension, adjustment or altitude compensation; snow, water, dirt or other foreign substance ingestion/contamination; improper maintenance; modified components; use of aftermarket or unapproved components, accessories, or attachments; unauthorized repairs; or repairs made after the warranty period expires or by an unauthorized repair center... This warranty excludes damages or failures caused by abuse, accident, fire, or any other cause other than a defect in materials or workmanship and provides no coverage for consumable components, general wear items, or any parts exposed to friction surfaces, stresses, environmental conditions and/or contamination for which they were not designed or not intended, including but not limited to the following items:

Page 89

warranty... This warranty provides no coverage for personal loss or expense, including mileage, transportation costs, hotels, meals, shipping or handling fees, motorcycle pick-up or delivery, replacement rentals, loss of vehicle use, loss of profits, or loss of vacation or personal time... THE EXCLUSIVE REMEDY FOR BREACH OF THIS WARRANTY SHALL BE, AT VICTORY MOTORCYCLES OPTION, REPAIR OR REPLACEMENT OF ANY DEFECTIVE MATERIALS, COMPONENTS, OR PRODUCTS... THE REMEDIES SET FORTH IN THIS WARRANTY ARE THE ONLY REMEDIES AVAILABLE TO ANY PERSON FOR BREACH OF THIS WARRANTY... VICTORY MOTORCYCLES SHALL HAVE NO LIABILITY TO ANY PERSON FOR INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES OF ANY DESCRIPTION, WHETHER ARISING OUT OF EXPRESS OR IMPLIED WARRANTY OR ANY OTHER CONTRACT, NEGLIGENCE, OR OTHER TORT OR OTHERWISE... THIS EXCLUSION OF CONSEQUENTIAL, INCIDENTAL, AND SPECIAL DAMAGES IS INDEPENDENT FROM AND SHALL SURVIVE ANY FINDING THAT THE EXCLUSIVE REMEDY FAILED OF ITS ESSENTIAL PURPOSE... THE IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE IS EXCLUDED FROM THIS LIMITED WARRANTY... ALL OTHER IMPLIED WARRANTIES (INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTY OF MERCHANTABILITY) ARE LIMITED IN DURATION TO THE ABOVE 12 MONTH WARRANTY PERIOD... VICTORY MOTORCYCLES DISCLAIMS ALL EXPRESS WARRANTIES NOT STATED IN THIS WARRANTY... SOME STATES DO NOT PERMIT THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES OR ALLOW LIMITATIONS ON THE DURATION OF IMPLIED WARRANTIES, SO THE ABOVE LIMITATIONS MAY NOT APPLY TO YOU IF INCONSISTENT WITH CONTROLLING STATE LAW...

Page 90

Warranties How To Obtain Warranty Service If your motorcycle requires warranty service, you must take it to a VICTORY MOTORCYCLES Servicing Dealer... When requesting warranty service you must present your copy of the Warranty Registration Form to the dealer... (THE COST OF TRANSPORTATION TO AND FROM THE DEALER IS YOUR RESPONSIBILITY... ) VICTORY MOTORCYCLES suggests that you use your original selling dealer; however, you may use any VICTORY MOTORCYCLES Servicing Dealer to perform warranty service... In the country where your motorcycle was purchased: Warranty or Service Bulletin repairs must be done by an authorized VICTORY MOTORCYCLES dealer... If you move or are traveling within the country where your motorcycle was purchased, Warranty and Service Bulletin repairs may be requested from any authorized VICTORY MOTORCYCLES dealer... Outside the country where your motorcycle was purchased: If you are traveling temporarily outside the country where your motorcycle was purchased, you should take your motorcycle to an authorized VICTORY MOTORCYCLES dealer... You must show the dealer photo identification from the country of the selling dealer's authorized location as proof of residence... Upon residence verification, the servicing dealer will be authorized to perform the warranty repair... If you move: If you move to another country, be sure to contact VICTORY MOTORCYCLES Customer Assistance and the customs department of the destination country before you move... Vehicle importation rules vary considerably from country to country... You may be required to present documentation of your move to VICTORY MOTORCYCLES in order to continue your warranty coverage... You may also be required to obtain documentation from VICTORY MOTORCYCLES in order to register your motorcycle in your new country... You should warranty register your motorcycle at a local VICTORY MOTORCYCLES dealer in your new country immediately after you move to continue your warranty coverage and to ensure that you receive information and notices regarding your motorcycle... If you purchase from a private party: If you purchase a VICTORY motorcycle from a private party, to be kept and used outside of the country in which the motorcycle was originally purchased, all warranty coverage will be denied... You must nonetheless register your motorcycle under your name and address with a local VICTORY MOTORCYCLES dealer in your country to ensure that you receive safety information and notices regarding your motorcycle...

Page 91

Notice If your vehicle is registered outside of the country where it was purchased and you have not followed the procedure set above, your vehicle will no longer be eligible for warranty or service bulletin coverage of any kind, other than safety bulletins... Vehicles registered to government officials or military personnel on assignment outside of the country where the vehicle was purchased will continue to be covered by the Limited Warranty... Please work with your dealer to resolve any warranty issues... Should your dealer require any additional assistance, they will contact the appropriate person at VICTORY MOTORCYCLES... This warranty gives you specific legal rights, and you may also have other rights which vary from state to state or in different countries... If any of the above terms are void because of federal, state, local law, all other warranty terms will remain in effect... For questions call VICTORY MOTORCYCLES Customer Assistance: United States & Canada: 1-877-737-7172 French: 1-800-268-6334

Page 92

Noise Emission Warranty VICTORY MOTORCYCLES warrants that this exhaust system, at the time of sale, meets all applicable U... S... EPA Federal noise standards... This warranty extends to the first person who buys this exhaust system for purposes other than resale, and to all subsequent buyers... Warranty claims should be directed to: An authorized VICTORY MOTORCYCLES dealer, or VICTORY MOTORCYCLES, 2100 Highway 55, Medina, MN 55340

Page 93

Warranties Emissions Control System Warranty Victory Motorcycle Division, Polaris Industries Inc... - Emission Control System Warranty Statement Your Warranty Rights and Obligations The California Air Resources Board and VICTORY MOTORCYCLES (hereinafter VICTORY) are pleased to explain the emission control system warranty on your 2014 or later VICTORY motorcycle... In California, new motor vehicles must be designed, built and equipped to meet the states stringent anti-smog standards... VICTORY must warrant the emission control system on your motorcycle for the periods of time listed below provided there has been no abuse, neglect or improper maintenance of your motorcycle... Your emission control system may include parts such as the fuel-injection system, the ignition system, catalytic converter and engine computer... Also included may be hoses, belts, connectors and other emission-related assemblies... Where a warrantable condition exists, VICTORY will repair your motorcycle at no cost to you, including diagnosis, parts and labor... Manufacturer's Warranty Coverage Class III motorcycles (280 cc and larger): for a period of use of five (5) years or 30,000 kilometers (18,641 miles), whichever first occurs... If an emission-related part on your motorcycle is defective, the part will be repaired or replaced by VICTORY... This is your emission control system DEFECTS WARRANTY... Owner's Warranty Responsibilities As the motorcycle owner, you are responsible for the performance of the required maintenance listed in your Rider's manual... VICTORY recommends that you retain all receipts covering maintenance on your motorcycle, but VICTORY cannot deny warranty solely for the lack of receipts or for your failure to ensure the performance of all scheduled maintenance... You are responsible for presenting your motorcycle to a VICTORY dealer as soon as a problem exists... The warranty repairs should be completed in a reasonable amount of time, not to exceed 30 days... As the motorcycle owner, you should be aware that VICTORY may deny your warranty coverage if your motorcycle or part has failed due to abuse, neglect, improper maintenance or unapproved modifications... If you have any questions regarding your warranty rights and responsibilities, you should contact Victory Motorcycle Division, Polaris Industries Inc... , 2100 Highway 55, Medina, Minnesota 55340 (Phone 877-737- 7172) or the California Air Resources Board, P... O... Box 8001, 9528 Telstar Avenue, El Monte, CA 91731...

Page 94

Warranties Emissions Control System Warranty I... Coverage Warranty defects shall be remedied during customary business hours at any authorized VICTORY dealer located within the United States of America in compliance with the Clean Air Act and applicable regulations of the United States Environmental Protection Agency and the California Air Resources Board... Any part or parts replaced under this warranty shall become the property of VICTORY... In the State of California only, emission-related warranted parts are specifically defined by the states Emission Warranty Parts List... These warranted parts are: carburetor and internal parts; intake manifold; fuel tank; fuel injection system; spark advance mechanism; crankcase breather; air cutoff valves; fuel tank cap for evaporative emission controlled vehicles; oil filler cap; pressure control valve; fuel/vapor separator; canister; igniters; breaker governors; ignition coils; ignition wires; ignition points; condensers, and spark plugs if failure occurs prior to the first scheduled replacement; and hoses, clamps, fittings and tubing used directly in these parts... Since emission- related parts may vary from model to model, certain models may not contain all of these parts and certain models may contain functionally equivalent parts... In the State of California only, Emission Control System emergency repairs, as provided for in the California Administrative Code, may be performed by other than an authorized VICTORY dealer... An emergency situation occurs when an authorized VICTORY dealer is not reasonably available, a part is not available within 30 days or a repair is not complete within 30 days... Any replacement part can be used in an emergency repair... VICTORY will reimburse the owner for expenses, including diagnosis, not to exceed VICTORYs suggested retail price for all warranted parts replaced and labor charges based on VICTORYs recommended time allowance for the warranty repair and the geographically appropriate hourly labor rate... The owner may be required to keep receipts and failed parts in order to receive compensation...

Page 95

Warranties Emissions Control System Warranty III... Limited Liability A... The liability of VICTORY under this Emission Control System Warranty is limited solely to the remedying of defects in material or workmanship by an authorized VICTORY dealer at its place of business during customary business hours... This warranty does not cover inconvenience or loss of use of the motorcycle or transportation of the motorcycle to or from the VICTORY dealer... VICTORY SHALL NOT BE LIABLE FOR ANY OTHER EXPENSES, LOSS OR DAMAGE, WHETHER DIRECT, INCIDENTAL, CONSEQUENTIAL OR EXEMPLARY ARISING IN CONNECTION WITH THE SALE OR USE OF OR INABILITY TO USE THE VICTORY FOR ANY PURPOSE... SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATIONS MAY NOT APPLY TO YOU... B... NO EXPRESS EMISSION CONTROL SYSTEM WARRANTY IS GIVEN BY VICTORY EXCEPT AS SPECIFICALLY SET FORTH HEREIN... ANY EMISSION CONTROL SYSTEM WARRANTY IMPLIED BY LAW, INCLUDING ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, IS LIMITED TO THE EXPRESS EMISSION CONTROL SYSTEM WARRANTY TERMS STATED IN THIS WARRANTY... THE FOREGOING STATEMENTS OF WARRANTY ARE EXCLUSIVE AND IN LIEU OF ALL OTHER REMEDIES... SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS SO THE ABOVE LIMITATIONS MAY NOT APPLY TO YOU... C... No dealer is authorized to modify this VICTORY Limited Emission Control System Warranty...

Page 96

Engine Engine Type VICTORY FREEDOM 106 / 6 V-Twin Configuration 4 Stroke 50 V-Twin Displacement 106 cu... in... (1731 cc) Cooling System / Oiling System Air & Oil / Wet Sump Compression Ratio 9... 4:1 Valve Train SOHC - 4 Valves Per Cylinder / Hydraulic Lifters & Cam

Page 97

Wheels and Tires Front Wheel Type / Size Cast 18 x 3... 5 or Billet 18 x 3... 0 Rear Wheel Type / Size Cast or Billet 18 x 8... 5 Front Tire Type / Size Dunlop D418F Elite 3 / 130/70 R18 63H Tubeless Rear Tire Type / Size Dunlop D419 Elite 3 / 250/40 R18 81V Tubeless

Page 98

Capacities Fuel 4... 5 gal... (17 l) Fuel Reserve ... 8 gal... (3... 0 l) (approximate) Engine Oil 5 qts... (4... 75 l)

Page 99

Engine Engine Type FREEDOM 106/6 V-Twin Configuration 4 Stroke 50 V-Twin Displacement 106 cu... in... (1731 cc) Cooling System Air & Oil Compression Ratio 9... 4:1 Valve Train 4 Valves Per Cylinder, Hydraulic Lifters & Cam Chain Adjusters Bore and Stroke 101 x 108 mm Fuel System/Throttle Body Bore Electronic Fuel Injection / 45 mm Exhaust System Dual-Staggered Slash-Cut with Common Volume Lubrication System Wet Sump Spark Plug/Gap NGK DCPR6E / ... 031-... 035 inch (0... 8-0... 9 mm)

Page 100

Specifications Fuel Specifications For best performance, use only unleaded gasoline with a 91 pump octane minimum (R+M/2 Method)... DO NOT USE E85 GASOLINE OR GASOLINE CONTAINING METHANOL... Using E85 gasoline or gasoline/methanol blends can result in poor starting and driveability, and may damage critical fuel system components... Gasoline containing up to 15% Methyl Tertiary Butyl Ether (MTBE) can be used... Gasoline containing up to 10% Ethanol can be used... Gasoline that has been reformulated or oxygenated can be used...

Page 103

Fluid Level, Front Brake... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 39 Fluid Level, Rear Brake ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 41 Fork Inspection ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 61 Front Axle Inspection ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 62 Front Brake Lever... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 31, 39 Front Fork Inspection ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 61 Fuel Cap Access ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 32 Fuel Fill Height... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 46 Fuel Filters ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 62 Fuel Hose Inspection ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 62 Fuel Hose, Rail and Connections ... ... ... ... ... ... ... ... ... ... ... ... ... 37 Fuel Level ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 37 Fuel Safety ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 18 Fuel Stabilizer ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 83 Fuel System Maintenance... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 62-63 Fuel System, Priming ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 46 Fuel Tank Removal/Installation ... ... ... ... ... ... ... ... ... ... ... ... ... ... 63 Fuse Recommendations ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 75 Fuse Replacement ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 75

Page 104

M Maintenance Record ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 99-100 Maintenance Requirements ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 51 Maintenance Schedule ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 52 Maintenance Table... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 52 Maintenance, Initial ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 51 Maintenance, Periodic ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 51 Maintenance, Safety ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 19 Metric Display ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 26 MFD... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 26-29 Mode Button ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 30 Modifications... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 15 Motorcycle Covers... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 84 Motorcycle Safety Foundation ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 9 Multi-Function Display ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 26-29

Page 105

T Throttle Cable Lubrication ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 64 Throttle Control Grip ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 31 Throttle Freeplay ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 41 Throttle Freeplay Adjustment... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 64 Throttle Inspection ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 41 Throttle Operation ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 49 Throttle System Maintenance ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 64 Tilt Sensor... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 47 Tire Condition... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 38 Tire Pressure ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 38 Tire Tread Depth... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 38 Tires ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 69

Page 106

To locate your nearest dealer, call 1-877-737-7172 or visit www... victorymotorcycles... com

Manualsnet FAQs

If you want to find out how the Vegas 8ball Polaris works, you can view and download the Polaris S,8Ball,Jackpot,HighBall,JudgeGunner Rider's Manual on the Manualsnet website.

Yes, we have the Rider's Manual for Polaris Vegas 8ball as well as other Polaris manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Rider's Manual should include all the details that are needed to use a Polaris Vegas 8ball. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Polaris S,8Ball,Jackpot,HighBall,JudgeGunner Rider's Manual is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Polaris S,8Ball,Jackpot,HighBall,JudgeGunner Rider's Manual consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Polaris S,8Ball,Jackpot,HighBall,JudgeGunner Rider's Manual free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Polaris S,8Ball,Jackpot,HighBall,JudgeGunner Rider's Manual, simply download the document to your computer. Once downloaded, open the PDF file and print the Polaris S,8Ball,Jackpot,HighBall,JudgeGunner Rider's Manual as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.