Polaris Cross Roads,Hard Ball,Tour Owner's Manual PDF

1 of 130
1 of 130

Summary of Content for Polaris Cross Roads,Hard Ball,Tour Owner's Manual PDF

2013 Owner's Manual

Victory Cross Roads

Victory Cross Country

Victory Cross Country Tour

Victory Cross Country Ness Signature Series

Ness Signature Series

Victory Cross Country Tour

Victory Cross Roads Hard-Ball TM

*9924043 *

For your nearest VICTORY dealer, visit www.polarisindustries.com

Polaris Sales Inc., 2100 Hwy. 55 Medina, MN 55340 USA

Part No. 9924043 Rev 01 Printed in USA

1

2013 Riders Manual

Victory Cross Roads

Victory Cross Roads Hard-Ball Victory Cross Country

Victory Cross Country Tour Ness Signature Series Victory Cross Country

Ness Signature Series Victory Cross Country Tour

2

Copyright 2012 Polaris Sales Inc. All information contained within this publication is based on the latest product information available at the time of publication. Product improvements or other changes may result in differences between this manual and the motorcycle. Depictions and/or procedures in this publication are intended for reference use only. No liability can be accepted for omissions or inaccuracies. Polaris Industries reserves the right to make changes at any time, without notice and without incurring obligation to make the same or similar changes to motorcycles previously built. Any reprinting or reuse of the depictions and/or procedures contained within, whether whole or in part, is expressly prohibited. All reference to RIGHT, LEFT, FRONT, REAR are from the operators perspective seated in a normal riding position. Features of VICTORY Motorcycles are covered by U.S. Patent Nos: 6,976,691; 6,407,663; D489670; D482311; D482304; D481980; D481973; D474142. The following are registered trademarks of Polaris Industries Inc.: POLARIS, THE WAY OUT, FREEDOM, VICTORY, VICTORY MOTORCYCLES, VICTORY CROSS ROADS and VICTORY CROSS COUNTRY. DUNLOP is a registered trademark of Dunlop Tire Corporation. LOCTITE is a registered trademark of Henkel Corporation. XM Ready is a registered trademark of XM Satellite Radio Inc. All rights reserved. iPod is a registered trademark of Apple Inc. Garmin and zumo are trademarks of Garmin Ltd. or its subsidiaries. HARD-BALL is a trademark of Polaris Industries Inc.

P/N 9924043

3

Table of Contents Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Component Identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Instruments, Features & Controls. . . . . . . . . . . . . . . . . . . . . . . . 19 Pre-Ride Inspections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55 Cleaning and Storage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93 Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103 Audio System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106

System Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106 System Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108 CB Radio / Intercom (ICOM) . . . . . . . . . . . . . . . . . . . . 115 AUX / iPod. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119 XM Radio. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121 NAV MP3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124

Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125

4

Introduction Thank you for purchasing a Polaris vehicle, and welcome to our world-wide family of Polaris owners. We proudly produce an exciting line of utility and recreational products. Snowmobiles All-terrain vehicles (ATVs) RANGER utility vehicles Low emission vehicles (LEVs) VICTORY MOTORCYCLES

For the safe and enjoyable operation of your vehicle, be sure to follow the instructions and recommendations in this riders manual. Keep this manual with the motorcycle, especially when ownership changes. If your riders manual is misplaced or damaged, please purchase a replacement from your VICTORY dealer. All references in this manual to RIGHT, LEFT, FRONT or REAR are from the operators perspective when seated in a normal riding position. If you have questions about the opera- tion or maintenance of your motorcycle after you've read this manual, please see your VIC- TORY dealer. To locate the nearest authorized VICTORY dealer, call 1-800-POLARIS or visit www.polarisindustries.com. VICTORY motorcycles comply with all federal, state and local safety and emission regula- tions for the area of intended sale.

5

Safety About the Rider's Manual

Failure to follow recommended precautions and procedures could result in severe injury or death. Always heed all safety precautions and follow all operation, inspection and maintenance procedures outlined in this manual.

This riders manual contains information that is essential to safe riding and proper mainte- nance of your VICTORY motorcycle. Anyone who uses the motorcycle (operators and pas- sengers) must read the riders manual before riding. Carefully read and understand the information found in the Safety section. Understand and follow the procedures outlined in the Maintenance section to keep your VICTORY motorcycle in top condition on the road or in storage. Bring the manual with you when you ride. Following the precautions and proce- dures in the manual will add to your enjoyment and help keep you riding safely. If you lose or damage this manual, you can purchase a new one through any authorized VICTORY dealer. The riders manual should be considered part of the motorcycle and remain with it if sold.

Safety Symbols and Signal Words The following signal words and symbols appear throughout this manual. Your safety and the safety of others is involved when these words and symbols are used. Become familiar with their meanings before reading the manual.

The safety alert symbol indicates a potential for personal injury.

WARNING WARNING indicates a hazardous situation which, if not avoided, could result in death or serious injury.

CAUTION CAUTION indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.

NOTICE NOTICE indicates a situation that may result in property damage.

WARNING

6

Safety Safe Riding Practices

Improper use of this motorcycle can result in serious injury or death to you, your passenger and others. To minimize the risk of injury, read and understand the information contained in this section before operating the motorcycle. This section contains safety information specific to the VICTORY motorcycle, as well as information about general motorcycle safety. Anyone who rides the motorcycle (operators and passengers) must follow these safety precautions.

Motorcycling has inherent risks. You can minimize those risks, but you can't eliminate them completely. Even if you're an experienced motorcycle operator or passenger, read all of the safety information in this man- ual before operating the motorcycle. Take a rider education course from the Motorcycle Safety Foundation or another qualified

instructor. The course will help you develop or refresh your expertise in safe riding habits through instruction and riding. For information on Motorcycle Safety Foundation rider education courses in your area, call 1-800-446-9227 or visit their home page at www.msf- usa.org.

Read and understand all information in this riders manual. Observe all maintenance requirements specified in this manual. For assistance, see the

VICTORY Service Manual or your authorized VICTORY dealer. Design characteristics affect how you should ride the VICTORY motorcycle: The motorcycle is designed for on-road use with one rider and one passenger. See the

manufacturers label (on the left side of the frame at the steering head). The label contains the Vehicle Identification Number (VIN) and Gross Vehicle Weight Rating (GVWR) and Gross Axle Weight Rating (GAWR) information. Never exceed the GVWR or the GAWR.

Riding off-road, riding with more than one passenger, or carrying weight exceeding the maximum weight rating can make handling difficult, which could cause loss of control.

During the first 500 miles (800 km) of operation, follow all break-in procedures as out- lined in the break-in section beginning on page 46. Failure to do so can result in serious engine damage.

Some VICTORY motorcycles include saddlebags, a windshield, a trunk, or a passenger backrest as standard equipment. To maintain stability, be prepared to reduce the operating speed of motorcycles equipped with these items.

WARNING

7

Safety Safe Riding Practices Follow these general safe riding practices: Before each ride, perform the pre-ride inspections as outlined beginning on page 38. Fail-

ure to do so may result in damage to the motorcycle or an accident. Until you're thoroughly familiar with the motorcycle and all of its controls, practice riding

where there is little or no traffic. Practice riding at a moderate speed on various road sur- faces and in different weather conditions.

Know your skills and limits, and ride within them. Allow only licensed, experienced operators to ride your motorcycle, and then only after

they have become familiar with its controls and operation. Make sure all riders read and understand this riders manual before riding.

Do not ride when you're fatigued or under the influence of alcohol, prescription drugs, over-the-counter drugs or any other drugs. Fatigue, alcohol and drugs can cause drowsi- ness, loss of coordination and loss of balance. They can also affect your awareness and judgment.

If your motorcycle operates abnormally, correct the problem immediately. See the VIC- TORY Service Manual or an authorized VICTORY dealer.

Ride defensively, as if you are invisible to other motorists, even in broad daylight. A motorist's failure to see or recognize a motorcycle is the leading cause of automobile/ motorcycle accidents. Ride where you're clearly visible to other motorists, and observe their behavior carefully.

Be especially cautious at intersections, as these are the most likely places for an accident. To prevent loss of control, keep your hands on the handlebars and your feet on the foot-

rests. Be aware that the highway bar is not designed to protect the rider from injury in a colli-

sion. Do not move or operate the motorcycle with the steering locked (if equipped), as the

severely restricted steering could result in loss of control. Obey the speed limit and adjust your speed and riding technique based on road, weather

and traffic conditions. As you travel faster, the influence of all other conditions increases, which can affect the motorcycle's stability and increase the possibility of losing control.

8

Safety Safe Riding Practices Reduce speed when:

the road has potholes, or is otherwise rough or uneven. the road contains sand, dirt, gravel or other loose substances. the road is wet, icy or oily. the road contains painted surfaces, manhole covers, metal grating, railway crossings or other

slippery surfaces. The weather is windy, rainy or otherwise causing slippery or rapidly changing conditions. Traffic is heavy, congested, not allowing sufficient space between vehicles or otherwise not flow-

ing smoothly. You are being passed in either direction by a large vehicle that produces a wind blast in its wake.

To maximize braking effectiveness, use the front and rear brakes together. Be aware of the following braking facts and practices:

The rear brake provides 40% of the motorcycle's stopping power, at most. Use the front and rear brakes together.

To avoid skidding, apply the brakes gradually when the road is wet or rough, or contains loose or other slippery substances.

If possible, avoid applying the brakes while making a turn. Motorcycle tires have less traction during turns, so braking will increase the possibility of skidding. Bring the motorcycle to the upright position before applying the brakes.

When approaching a curve, choose a speed and lean angle that allows you to pass through the curve in your own lane without applying the brakes. Excessive speed, improper lean angle or braking in a curve can cause loss of control.

Ground clearance is reduced when the motorcycle leans. Do not allow components to con- tact the road surface when leaning the motorcycle in a curve, as this could cause loss of control.

Retract the sidestand fully before riding. If the sidestand is not fully retracted, it could con- tact the road surface and cause loss of control.

Do not tow a trailer. Towing a trailer can make the motorcycle hard to handle.

Anti-Lock Brake System Response When the anti-lock brakes engage during a braking event, the rider will feel pulsing at the

brake levers. Continue to apply steady pressure to the brakes for the best stopping perfor- mance.

9

Safety Safe Riding Practices Carrying a Passenger Do not carry a passenger unless the motorcycle is equipped with passenger seat and passen- ger footrests. To carry a passenger safely: Do not exceed the gross vehicle weight rating (GVWR) for your motorcycle. Direct the passenger to hold onto you or to the passenger hand grips with both hands and

to keep both feet on the passenger footrests. Do not carry a passenger who cannot place both feet firmly on the passenger footrests. A passenger who is not holding on properly, or who cannot reach the passenger footrests, can shift their body erratically, which can make the motorcycle hard to handle and cause loss of control.

To obtain the best ride and handling characteristics, adjust the rear shock absorber air pres- sure. See page 68.

Before riding, be sure your passenger knows safe riding procedures. Discuss any safety information unfamiliar to your passenger. A passenger who is unaware of safe riding pro- cedures may distract you or make movements that make the motorcycle hard to handle.

Adjust your riding style to compensate for the differences in handling, acceleration and braking caused by the additional weight of the passenger. Failure to do so can cause loss of control.

Protective Apparel Wear protective apparel to decrease the risk of injury and increase riding comfort. Always wear a helmet that meets or exceeds established safety standards. Approved hel-

mets in the USA and Canada bear a U.S. Department of Transportation (DOT) label. Laws in some areas require that you wear an approved helmet. Head injuries are the leading cause of fatalities in accidents involving motorcycles. Statistics prove that an approved helmet is the most effective protection in preventing or reducing head injuries.

Wear eye protection to protect eyes from wind or airborne particles and objects. Laws in some areas require that you wear eye protection. VICTORY recommends that you wear approved Personal Protective Equipment (PPE) bearing markings such as VESC 8, V-8, Z87.1, or CE. Make sure protective eyewear is kept clean.

All riders should wear bright or light-colored and/or reflective clothing to improve visibil- ity to other motorists. A motorist's failure to see or recognize a motorcycle is the leading cause of automobile/motorcycle accidents.

Wear gloves, a jacket, heavy boots and long pants to prevent or reduce injury from abra- sions, lacerations or burns should the motorcycle fall. Wear boots with low heels, as high heels can catch on pedals or footrests. The combination of boots and pants should com- pletely cover legs, ankles and feet, protecting skin from engine and exhaust system heat.

Do not wear loose, flowing clothing or long boot laces, as they can catch on handlebars, levers or footrests, or they can become entangled in the wheels, causing loss of control and serious injury.

10

Safety Use of Accessories Because VICTORY cannot test and make specific recommendations concerning every acces- sory or combination of accessories sold, the operator is responsible for determining that the motorcycle can be safely operated with any accessories or additional weight. Use the follow- ing guidelines when choosing and installing accessories: Do not install accessories that impair the stability, handling or operation of the motorcycle.

Before installing an accessory, be sure that it does not: Reduce ground clearance when the motorcycle is either leaned or in a vertical position. Limit suspension or steering travel or your ability to operate controls. Displace you from your normal riding position. Obscure lights or reflectors.

Bulky or large accessories can cause instability (due to the lifting or buffeting effects of wind) and loss of control.

Do not install electrical accessories that exceed the capacity of the motorcycles electrical system. Never install higher wattage light bulbs than those supplied as original equipment. An electrical failure could result and cause hazardous loss of engine power or lights, or damage to the electrical system. See page 89.

Use only genuine VICTORY accessories designed for your model.

Modifications Modifying the motorcycle by removing any equipment or by adding equipment not approved by VICTORY may void your warranty. Such modifications could make the motorcycle unsafe to ride and could result in severe injury to operator or passengers, as well as damage to the motorcycle. Some modifications may not be legal in your area of operation. If in doubt, contact your authorized VICTORY dealer.

Parking the Motorcycle When leaving the motorcycle unattended, turn the engine off. Remove the ignition key to prevent unauthorized use. Park the motorcycle where people are not likely to touch the hot engine or exhaust system or place combustible materials near these hot areas. Do not park near a flammable source such as a kerosene heater or an open flame, where hot components could ignite combustible mate- rials. Park the motorcycle on a firm, level surface. Sloped or soft surfaces may not support the motorcycle. If you must park on a slope or soft surface, follow the precautions outlined on page 53.

11

Safety Carrying Cargo Use the following guidelines when attaching cargo or accessories to the motorcycle. Where applicable, these guidelines also refer to the contents of any accessories. Keep cargo and accessory weight to a minimum, and keep items as close to the motorcycle

as possible to minimize a change in the motorcycles center of gravity. Changing the cen- ter of gravity can cause loss of stability and handling and could cause loss of control.

Distribute weight evenly on both sides of the motorcycle. Maintain even weight distribu- tion by checking accessories and cargo to make sure theyre securely attached to the motorcycle before riding and whenever you take a break from riding. Uneven weight dis- tribution, or accessories or cargo that shift suddenly while youre riding can make the motorcycle hard to handle and could cause loss of control.

Do not attach large or heavy cargo such as sleeping bags, duffel bags or tents to the han- dlebars, front fork area or front fender. Cargo or accessories placed in these areas can cause instability (due to improper weight distribution or aerodynamic changes) and could cause loss of control. Such items can also block air flow to the engine and cause overheat- ing that can damage the engine.

Do not exceed the maximum cargo weight limit of any accessory (see accessory instruc- tions and labels). Do not attach cargo to an accessory not designed for that purpose. Either circumstance could result in an accessory failure that could cause loss of control.

Do not attach anything to the motorcycle unless specifically designed for that purpose by VICTORY.

Saddlebags and Trunk (if equipped) WARNING! Operating this vehicle without saddlebags could result in severe injury or death. Never operate this vehicle if the saddlebags are not in place and properly secured. Whenever operating a motorcycle with saddlebags: Never ride at excessive speeds. Saddlebags, combined with the lifting or buffeting effects

of wind, can make the motorcycle unstable and cause loss of control. Distribute weight evenly in each of the saddlebags. Do not exceed the individual weight limit of each saddlebag or the trunk. A weight capac-

ity label is attached inside for reference. NEVER EXCEED GROSS VEHICLE WEIGHT RATING (GVWR) or the GROSS

AXLE WEIGHT RATING (GAWR), regardless of whether or not the saddlebags and/or trunk are loaded to capacity. Exceeding the weight rating can reduce stability and handling and cause loss of control.

12

Safety Transporting the Motorcycle If you must transport the motorcycle: Use a truck or trailer. Do not tow the motorcycle

with another vehicle, as towing will impair the motorcycle's steering and handling.

Position and restrain the motorcycle so it remains upright on the truck or trailer. If the motorcycle leans to one side, gasoline may leak from the fuel tank and result in a fire hazard or damage to the fin- ish.

Do not restrain the motorcycle using the handlebars. Place tiedown straps around the fork tubes above

the lower triple clamp. Place tiedowns as wide apart as possible on the truck or trailer bed for best stabil- ity.

Fuel and Exhaust Safety Always heed these fuel safety warnings when refueling or servicing the fuel system. For fueling procedures, see page 47.

Gasoline is highly flammable and explosive under certain conditions. Always exercise extreme caution whenever handling gasoline. Always turn off the engine before refueling. Always refuel outdoors or in a well-ventilated area. Open the fuel cap slowly. Do not overfill the tank. Do not fill the tank neck. Do not smoke or allow open flames or sparks in or near the area where refueling is performed or

where gasoline is stored.

Gasoline and gasoline vapors are poisonous and can cause severe injury. Do not swallow gasoline, inhale gasoline vapors, or spill gasoline. If you swallow gasoline, inhale

more than a few breaths of gasoline vapor, or get gasoline in your eyes, see a physician immediately.

If gasoline spills on your skin or clothing, immediately wash it off with soap and water and change clothing.

Exhaust gases contain carbon monoxide, a colorless, odorless gas that can cause loss of consciousness or death in a short time. Never start the engine or let it run in an enclosed area. Never inhale exhaust gases.

To lower triple clamp (one tiedown each side)

To swing arm (one tiedown each side)

WARNING

13

Safety Safety Maintenance

Failure to perform safety maintenance as recommended can result in difficult handling and loss of control, which could result in serious injury or death. Always perform the safety maintenance procedures as recommended. Perform maintenance and repairs promptly as outlined in the VICTORY service manual, or see your authorized VICTORY dealer for service.

Before each ride, perform the Pre-Ride Inspections. See page 38. Perform all periodic maintenance at the recommended intervals outlined in the Periodic

Maintenance section beginning on page 56. Always maintain proper tire pressure, tread condition and wheel and tire balance. Inspect

tires regularly and replace worn or damaged tires promptly. Use only approved replace- ment tires.

Always ensure proper steering head bearing adjustment. Regularly inspect the rear shock absorber and the front forks for fluid leaks or damage. Make any necessary repairs promptly.

Clean the motorcycle thoroughly to reveal items in need of repair. Make sure all legally required equipment is properly installed and in good condition,

including the license plate. Fasteners must meet original specifications for quality, finish and type to ensure safety.

Use only genuine VICTORY replacement parts, and ensure that all fasteners are tightened to the proper torque.

Electromagnetic Interference This vehicle complies with European directive 97/24/EC Chapter 8 requirements, which is equivalent to Canadian ICES-002.

WARNING

14

Safety Gross Vehicle Weight Rating (GVWR) WARNING! Exceeding the gross vehicle weight rating of your motorcycle can reduce stability and han- dling and could cause loss of control. NEVER exceed the GVWR of your motorcycle. The maximum load capacity of your motorcycle is the maximum weight you may add to your motorcycle without exceeding the GVWR. This capacity is determined by calculating the difference between your motorcycles GVWR and wet weight. Refer to the specification section of this manual or the Manufacturing Information/VIN label on the motorcycle frame for model-specific information. Refer to the Safety and Informa- tion Labels section in this manual for location on the motorcycle. When determining the weight you will be adding to your motorcycle, and to ensure you do not exceed the maximum load capacity, include the following: operator body weight passenger body weight weight of all riders apparel and items in or on apparel weight of any accessories and their contents weight of any additional cargo on the motorcycle

Safety and Information Labels E-Marks

Muffler E-Marks

Air Box E-Marks

Tire E-Mark (on side of tire that

contains serial number)

15

Safety Safety and Information Labels Labels are model-specific and market-specific. Your motorcycle may not contain all of the labels shown. 1. Manufacturing Information Label 2. Operator/Fuel Warning 3. Cargo Information (in saddlebags) 4. Shock Air Pressure Label 5. Saddlebag Warning 6. Highway Bar Warning 7. Trunk Cargo Information Label (if equipped) 8. Lower Fairing Cargo Information Labels (both compartments) (if equipped)

1 2

3

4

5

6

EU Motorcycle Stationary

Noise Level

EU Whole Vehicle Type Approval

Number

ECE Separate System Approval

Number

VIN

General Representation of Manufacturing Information Label for

Illustration Purposes Only

7

8

16

Identification Ignition Key Number The ignition key number is stamped on the small metal tag attached to the key ring. Remove the tag and record the number on page 105. Store the tag in a safe place. Additional keys can be copied from one of the original keys. A VICTORY key blank is required. If you lose both original keys, you will need the following:

Key number (recorded on page 105) A new key blank from a VICTORY dealer Proof of ownership A locksmith or VICTORY dealer with the equipment necessary to cut a new key

Engine Identification Number The engine number is stamped into the right crankcase behind the rear cylinder. Record the number in the space provided on page 105. Engine

Number

17

Identification Left Side View 1. Spark Plugs 2. Front Brake Caliper 3. Oil Cooler 4. Battery 5. Gear Shift Pedal 6. Operator Footrest 7. Sidestand 8. Oil Drain Plug 9. Oil Filter 10. Passenger Footpeg 11. Rear Brake Caliper 12. Diagnostic Connector

(under cover)

Right Side View 1. Exhaust Mufflers 2. Drive Belt Guard 3. Drive Sprocket (under cover) 4. Engine Oil Fill Cap / Dipstick 5. Rear Brake Fluid Reservoir 6. Rear Brake Pedal 7. Air Filter 8. Headlamp 9. Mirror 10. Fuel Tank 11. Access Cover 12. Fuse Box (under cover) 13. Accessory Fuse (under

cover) 14. Rear Shock Air Fitting (under

cover) 15. Radio Antenna (if equipped) 16. License Plate Bracket

1

2

5 6

7 8

9 10

113 4

12

2 3 4 6

12

14

1

8

7

5

16

15

9

10 13 11

18

Identification Top View 1. Windshield 2. Clutch Lever 3. Fuel Filler Cap 4. Operator Seat 5. Passenger Seat 6. Saddlebag Latch 7. Turn Signals 8. Tail Lamps 9. Front Brake Lever 10. Front Brake Fluid Reservoir 11. Radio Fuse (inside fairing)

Console (CROSS COUNTRY) 1. Speakers 2. Mode Switch 3. Fuel Gauge 4. Speedometer 5. Indicator Lamp Display 6. Multi-Function Display 7. Tachometer 8. Volt Meter 9. Left Handlebar Switches 10. iPod Cord and 12-Volt Outlet (TOUR

model, left compartment) 11. Audio Control Switches 12. 12-Volt Accessory Outlet 13. Radio Display 14. Heated Grip Switch (if equipped) 15. Cruise Control Switches (if equipped) 16. Right Handlebar Switches

Console (CROSS ROADS) 1. Clutch Lever 2. Mirror 3. Speedometer 4. Indicator Light Panel 5. Tachometer (if equipped) 6. Front Brake Fluid Reservoir 7. Front Brake Lever 8. Throttle Control Grip 9. Switches 10. Throttle Cables 11. Fuel Cap 12. Auxiliary Forward Lighting

Switch (if equipped) 13. Cruise Control Switches

1 2 4 5

910

3

6 7

8 11

1 3 4 5 6

7 8

9

1

11 1615

2

1312 14

10

3 5

1

9

11

4

10 9

7

8

2

6

1312

19

Instruments, Features and Controls Ignition Switch The ignition key operates the ignition switch and parking lights. The ignition switch provides electrical power to the ignition, the lighting system and all electrical switches and buttons. Before starting the engine, read the instructions for starting the engine. See page 48.

Engine Off In the OFF position, all electrical circuits are inactive and the ignition key can be removed. Turn the ignition switch to the OFF position and remove the ignition key when leaving the motor- cycle unattended.

Engine On/All Lights On In the ON position, all electrical circuits are ener- gized and the ignition key cannot be removed. The headlamp, taillight, and instrument lights illuminate. The engine stop/run switch must be in the RUN position to start the engine or activate the turn signals and other electrical features.

Parking Lights On In the PARKING LIGHTS ON position, the taillight, indicator lights and license plate light illuminate. The radio can be operated and the instrumentation is active. The emergency flashers can be activated, and the ignition key can be removed. You must push the ignition key into the switch while selecting this position.

Seat Heater Switches (CROSS COUNTRY TOUR) The seat heater switches are located on the lower left edge of the seat. Toggle Up: High Toggle Down: Low Toggle Center: Off

Engine Off Engine On/All Lights On

Parking Lights On

Drivers Seat Switch

Passengers Seat Switch

20

Instruments, Features and Controls Instrument Cluster (CROSS ROADS) Speedometer The speedometer displays vehicle speed in either miles per hour (MPH) or kilometers per hour (km/h).

Indicator Lamps Lamp Indicates Condition

Neutral This lamp illuminates when the transmission is in neutral and the ignition key is in the ON position.

High Beam This lamp illuminates when the headlamp switch is set to high beam.

Turn Signal The turn signal indicator flashes when the left, right, or both turn signals (hazard) are active. If a bulb fails, or if there is a short circuit in the signal system, the lamp flashes at more than twice the normal rate.

Low Fuel This lamp illuminates when approximately one gallon (3.8 liters) of fuel remains in the fuel tank.

Cruise Control Engaged

Before using the cruise control (if equipped), read the safety and operation procedures beginning on page 51.

Check Engine This lamp illuminates momentarily when the ignition switch is in the ON position and the engine is off. This indicates proper function. This lamp will illuminate if the engine is disabled by the sidestand interlock switch. See page 34. The light will also remain on if the tilt sensor shuts down the engine. See page 34. If this lamp illuminates while the engine is running, contact an authorized VICTORY dealer promptly for diagnosis. If abnormal sensor or engine operation is detected the light will remain on as long as the fault condition exists. Retrieve the error codes for diagnosis. See page 26.

Anti-Lock Brake System Not Activated (if equipped)

The ABS indicator always illuminates when the key is in the ON position and remains on until the anti-lock system activates, which occurs when vehicle speed exceeds 6 MPH (10 km/h). When the lamp is illuminated, the anti-lock brakes will not activate, but the conventional brake system will continue to operate normally.

Speedometer Indicator Lamps

Multi-Function Display

21

Instruments, Features and Controls Instrument Cluster (CROSS ROADS) Multi-Function Display Use the mode button to toggle through the modes of the multi-function display. See page 29. Press and hold the mode button to reset the trip odometers, average fuel economy, average speed and trip hour meter.

Odometer The odometer displays total distance traveled. Trip Odometers The ignition switch must be in the ON or PARK position to access the trip odometers. The trip odometers (Trip 1 and Trip 2) display total distance traveled since being reset. To reset a trip odometer, toggle to the trip odometer, then press and hold the mode button until the trip odometer resets to zero. Fuel Level The fuel level displays bar graph- ics between empty (E) and full (F) to indicate the fuel level. Engine Speed Engine speed displays in revolutions per minute (RPM). DC Voltage (Optional) The volt meter displays battery voltage. If the engine is not running, approximate battery voltage displays. If the engine is running, approximate charging voltage displays. Gear Position Gear position displays only when the vehicle is moving and the clutch is engaged. If the vehicle stops moving, or if the clutch is disengaged, -- will show in the display. Temperature (Optional) The key must be in the ON or PARK position to display ambient air temperature.

Modes Available Standard Modes Optional Modes

Odometer Trip Odometer 2 Trip Odometer 1 Average Fuel Economy

Clock Instantaneous Fuel Economy Gear Indicator Trip Time

Fuel Level Gauge Average Speed Engine Speed DC Voltage

Ambient Air Temperature

Fuel Level FULL

22

Instruments, Features and Controls Instrument Cluster (CROSS ROADS) Multi-Function Display Display Units (Standard/Metric) The display can be changed to display either standard or metric units of measurement.

1. Turn the key to the OFF position. 2. Press and hold the mode button while turning the key to the ON or PARK position. 3. When the display flashes the distance setting, tap the mode button to advance to the

desired setting. 4. Press and hold the mode button to save the setting and advance to the next display

option. 5. Repeat the procedure to change remaining display settings. Clock Tip: The clock must be reset any time the battery has been disconnected or discharged. 1. Turn the key to ON or PARK. Use the mode button to toggle to the odometer display. 2. Press and hold the mode button until the hour segment flashes. Release the button. 3. With the segment flashing, tap the mode button to advance to the desired setting. 4. Press and hold the mode button until the next segment flashes. Release the button. 5. Repeat steps 3-4 twice to set the 10-minute and 1-minute segments. After completing the

1-minute segment, step 4 will save the new settings and exit the clock mode. 6. Turn the key to the OFF position. Trip Hours Meter The trip hours meter displays total hours of operation since being reset. To reset the trip hours meter, toggle to the hours meter display, then press and hold the mode button until the meter resets to zero. Diagnostic Functionality Certain conditions will cause an error message to display in the screen. If this occurs, please see your VICTORY dealer.

Standard Display Metric Display Distance Miles Kilometers Fuel U.S. Gallons I = Imperial Gallons Liter = Liters Temperature Fahrenheit Celsius Time 12-Hour Clock 24-Hour Clock

Message Location Indicates LO DC Voltage Screen Voltage remains below 11.0 volts for more than 10 seconds OV DC Voltage Screen Voltage remains above 15.0 volts for more than 10 seconds

ERROR All Checksum error (gauge malfunction)

23

Instruments, Features and Controls Instrument Cluster (CROSS ROADS) Multi-Function Display Engine Error Codes The error screen displays only when the CHECK ENGINE light is on or when it goes on and off during one ignition cycle. Error codes are not stored. When the key is turned OFF, the code and message is lost, but will reappear if the fault reoccurs after restarting the engine. If the CHECK ENGINE indicator lamp illu- minates, retrieve the error codes from the display. 1. If the error codes are not displayed, use

the mode button to toggle until Ck ENG displays on the main line of the display.

2. Press and hold the mode button to enter the diagnostics code menu. 3. Record the three numbers displayed in the gear position, clock and odometer displays. 4. See an authorized VICTORY dealer for code details and diagnosis.

Low Oil Pressure Display LO OIL displays under the following conditions.

Condition Indicates Action Required Engine oil pressure has dropped while the engine is running.

Oil pressure is below a safe operating pressure.

Stop the engine as soon as safely possible and check the oil level. If the oil level is sufficient, but LO OIL continues to display after restart- ing the engine, stop the engine immediately.

The key is turned to ON or PARK.

The indicator circuit is operating properly.

None - After two seconds the display will return to the most recently active menu.

The stop/run switch is moved to STOP.

The system is operating properly.

Press and release the MODE button to return to the most recently active menu.

Suspect Parameter Number (SPN)Error Code

Number (0-9)

Failure Mode Indicator (FMI)

24

Instruments, Features and Controls Instrument Cluster (CROSS COUNTRY) The instrument cluster includes the speedometer, tachometer, fuel gauge, volt meter, indica- tor lamps and multi-function display.

Speedometer The speedometer displays vehicle speed in either miles per hour or kilometers per hour. Tachometer The tachometer displays engine speed in revolutions per minute (RPM). A red line on the face of the gauge indicates the maximum safe engine speed. WARNING! Excessive engine speed can cause engine damage or failure, which could result in serious injury or death. Do not allow engine speed to exceed the red line. Fuel Gauge The fuel gauge displays fuel level. The key must be in the ON or PARK position. For the most accurate reading, sit on the motorcycle and bring it to the upright position. Volt Meter When the key is in the ON position, the volt meter displays battery voltage. If the engine is not running, approximate battery voltage displays. If the engine is running, approximate charging voltage displays.

Speedometer Tachometer

Fuel Gauge Volt Meter

Indicator Lamps

Multi-Function Display

25

Instruments, Features and Controls Instrument Cluster (CROSS COUNTRY) Indicator Lamps

Lamp Indicates Condition Neutral This lamp illuminates when the transmission is in neutral and the ignition

key is in the ON or PARK position.

High Beam This lamp illuminates when the headlamp switch is set to high beam.

Check Engine This lamp illuminates momentarily when the ignition switch is in the ON position and the engine is off. This indicates proper function. If this lamp illuminates while the engine is running, contact an authorized VICTORY dealer promptly for diagnosis. The light will remain on if the tilt sensor shuts down the engine. See page 34. If abnormal sensor or engine operation is detected the light will remain on as long as the fault condition exists. Retrieve the error codes for diagnosis. See page 26. This lamp is also known as a malfunction indicator lamp (MIL).

Turn Signal One arrow flashes when the corresponding turn signal is activated. Both arrows flash when the hazard signal is activated. If a bulb fails, or if there is a short circuit in the signal system, the lamp flashes at more than twice the normal rate.

Low Oil Pressure

This lamp illuminates when the ignition switch is in the ON position and the engine is off, indicating that the indicator circuit is functioning properly. This lamp also illuminates if engine oil pressure drops below safe operating pressure. If this lamp illuminates while the engine is running, turn the engine off as soon as safely possible and check the oil level. If the oil level is correct and the lamp remains on after the engine is restarted, turn the engine off immediately.

Low Fuel This lamp illuminates when approximately one gallon (3.8 liters) of fuel remains in the fuel tank.

Low Battery Warning

This lamp illuminates when battery voltage is low. Make sure the charging system is operating properly. See page 92.

Cruise Control Engaged

Before using the cruise control, read the safety and operation procedures beginning on page 51.

Anti-Lock Brake System Not Activated (if equipped)

The ABS indicator always illuminates when the key is in the ON position and remains on until the anti-lock system activates, which occurs when vehicle speed exceeds 6 MPH (10 km/h). When the lamp is illuminated, the anti-lock brakes will not activate, but the conventional brake system will continue to operate normally.

Left Turn Low Fuel

Cruise Control Oil Pressure

High Beam

Check Engine

Right Turn

Neutral Battery Warning

Anti-Lock Brake System

(ABS)

26

Instruments, Features and Controls Instrument Cluster (CROSS COUNTRY) Multi-Function Display Use the mode button to toggle through the modes of the multi-function display. See page 29. Permanently Displayed Modes Clock Gear Position Ambient Temperature

Trip Computer Modes Odometer Trip Odometers (Trip 1, Trip 2) Average Fuel Economy Average Speed Fuel Range Instantaneous Fuel Economy Trip Hours Meter Tip: Press and hold the mode button to reset the trip odometer, average fuel economy, average speed

or trip hours meter.

Engine Error Codes The error screen displays only when the CHECK ENGINE light is on or when it goes on and off during one ignition cycle. Error codes are not stored. When the key is turned OFF, the code and message is lost, but will reappear if the fault reoccurs after restarting the engine. If the CHECK ENGINE indicator lamp illumi- nates, retrieve the error codes from the display. 1. If the error codes are not displayed, use the

mode button to toggle until Err displays in the clock area.

2. Record the three code numbers displayed in the gear position, temperature and odometer displays.

3. See an authorized VICTORY dealer for code details and diagnosis.

Gear Position

Trip Computer

Clock

Temperature

Avg C F888188:88

8.88 :88 :8 Speed Range Inst Time

TRIP 1 TRIP 2

km / h miles / gal

Err

Suspect Parameter Number (SPN)

Error Code Number (0-9)

Failure Mode Indicator (FMI)

27

Instruments, Features and Controls Instrument Cluster (CROSS COUNTRY) Multi-Function Display Display Units (Standard/Metric) The display can be changed to display either standard or metric units of measurement. Tip: To exit the set-up mode at any time, wait 10 seconds.The display automatically exits and returns to

the odometer display.

Display Units (Standard/Metric) 1. Turn the key to the OFF position. 2. Press and hold the mode button while turning the key to the ON or PARK position. 3. When the display flashes the distance setting, tap the mode button to advance to the

desired setting. 4. Press and hold the mode button to save the setting and advance to the next display

option. 5. Repeat the procedure to change remaining display settings. Clock Tip: The clock must be reset any time the battery has been disconnected or discharged. 1. Turn the key to ON or PARK. Use the mode button to toggle to the odometer display. Tip: If LOW FUEL is flashing, the display will not enter the CLOCK SET mode. 2. Press and hold the mode button until the hour segment flashes. Release the button. 3. With the segment flashing, tap the mode button to advance to the desired setting. 4. Press and hold the mode button until the next segment flashes. Release the button. 5. Repeat steps 3-4 twice to set the 10-minute and 1-minute segments. After completing the

1-minute segment, step 4 will save the new settings and exit the clock mode. 6. Turn the key to the OFF position.

Standard Display Metric Display Distance Miles Kilometers Fuel U.S. Gallons I = Imperial Gallons Liter = Liters Temperature Fahrenheit Celsius Time 12-Hour Clock 24-Hour Clock

28

Instruments, Features and Controls Instrument Cluster (CROSS COUNTRY) Multi-Function Display Odometer/Trip Odometer The odometer displays the total distance traveled by the vehicle. The trip odometer displays distance traveled since the trip odometer was reset. To view the trip odometer, turn the key to the ON position. Use the mode button to toggle to the trip odometer. To reset the trip odometer, toggle to the trip odometer, then press and hold the mode button until the trip odometer resets. Gear Position Gear position displays only when the vehicle is moving and the clutch is engaged. If the vehicle stops moving, or if the clutch is disengaged, -- will show in the display. Temperature The key must be in the ON or PARK position to display ambient air temperature.

Console Switches (CROSS COUNTRY)

Hand Grip Heater Switch Press the top (high heat) or bottom (low heat) of the rocker switch to turn the hand grip heaters on. Move the switch to the center position to turn the heat- ers off.

Hand Grip Heater Switch

Optional Accessory Switch

High

Off

Low

29

Instruments, Features and Controls Left Handlebar Switches

Audio Switches (if equipped) See page 106 for audio systems operation.

Mode Button The mode button is located on the front side of the left handlebar switch. Use the mode button to toggle through the modes of the multi-function display. If Err displays while toggling through the features, a system error has been logged. See page 26. Use the mode button to set the display units to either standard or metric units of measurement (CROSS COUNTRY). See page 27.

Starter Interlock Switch The starter interlock switch prevents the electric starter from operating when the transmission is in gear and the clutch is engaged (lever released). Read the engine starting procedures beginning on page 48 before starting the engine. WARNING! Never start the engine with the transmission in gear and the clutch disengaged unless you are properly seated with the front brake applied.

Lamp Switch Description Emergency Flasher Switch (Hazard Switch)

The emergency flasher switch activates and cancels the emergency flashers. When the emergency flashers are active, all of the turn signals flash. Press the top of the switch to activate the emergency flashers. Press the bottom of the switch to cancel the flashers.

High Beam/Low Beam Light Switch

The headlight high/low beam switch toggles the headlight between high beam and low beam. To activate the high beam, press the upper portion of the switch; to activate the low beam, press the lower portion of the switch.

Horn Button To sound the horn, press the horn button.

Turn Signal Switch

Move the switch to the left to activate the left turn signals. Move the switch to the right to activate the right turn signals. A signal will deacti- vate automatically when speed or distance reach predetermined levels. To cancel a signal manually, move the switch to the center position and push it inward. Momentary Feature: Move the turn signal switch left or right and hold it in that position for at least one second. The momentary feature will acti- vate and the signal will then cancel when the switch is released.

Flasher (Hazard) Switch

High/Low Light Switch

Horn ButtonTurn Signal Switch

Audio Switches Mode Button

Clutch Lever

Interlock Switch

30

Instruments, Features and Controls Right Handlebar Switches Engine Stop/Run Switch The engine stop/run switch is located on the right handle- bar. This switch completes or interrupts the ignition, starter and fuel pump circuits. Use the engine stop/run switch to turn the engine off quickly. Turn the key off after the engine stops. Press the bottom of the switch (RUN) to complete the

circuits and allow the engine to start and run. Press the top of the switch (STOP) to interrupt the cir-

cuits and stop the engine. The engine should not start or run when the switch is in the STOP position.

Cruise Control Switches (if equipped) Refer to the Cruise Control section of this manual (begin- ning on page 51) for cruise control operation.

Engine Starter Switch The starter switch is located on the right handlebar. Use the starter switch to start the engine and operate in reverse (if equipped). The switch will operate only when the engine stop/run switch is in the RUN position and the transmis- sion is in neutral (or the clutch is disengaged). The reverse lever (if equipped) must also be disengaged. Tip: If the reverse system fuse has blown, the starter switch will

not function even if the reverse lever is disengaged. Replace the fuse. See page 88.

Read the engine starting procedures before starting the engine. See page 48. Press the right side of the starter switch to engage the

starter motor. See page 54 for reverse operation.

Run Stop

Cruise Control Switches

Starter Switch

31

Instruments, Features and Controls Throttle Control Grip The throttle control grip is located on the right handlebar. Use the throttle control grip to control engine speed. While seated in the proper riding position: Rotate the top of the grip rearward to

increase engine speed and power. Rotate the top of the grip forward to

decrease engine speed and power.

Clutch Lever The clutch lever is located on the left handle- bar. Disengage the clutch before shifting gears. For smooth clutch operation, pull the lever quickly and release it gradually. To disengage the clutch, pull the lever

toward the handlebar. To engage the clutch, gradually release the

lever.

Gear Shift Pedal The gear shift pedal is located on the left side of the motorcycle. Press downward on the gear shift pedal to shift

to a lower gear. Lift up on the gear shift pedal to shift to a

higher gear. See page 33 for pedal adjustment options. See pages 49-50 for gear shifting procedures.

Saddlebag and Trunk Door Locks Use the ignition key to lock and unlock the trunk and sad- dlebag doors. The doors should be locked before riding. Tip: Not all models are equipped with a trunk. To lock a door, place the key in the lock and turn it coun- ter-clockwise. To unlock a door, turn the key clockwise. After unlocking a door, press the door lock to release the latch and open the door. Refer to the Gross Vehicle Weight Rating information beginning on page 14 for loading information.

Increase Speed

Decrease Speed

Clutch Lever

Gear Shift Pedal

Lock

Unlock

Lock

Unlock

32

Instruments, Features and Controls Fuel Cap Use the ignition key to lock and unlock the fuel cap. Always lock the fuel cap before riding. An open fuel cap could contact the handlebar. To open the fuel cap, lift the lock cover. Place the key in the lock and turn it clockwise. To secure the fuel cap, push the cap down to engage the latch. Turn the key counter-clockwise to lock the cap.

Brakes Anti-Lock Brake System (ABS) (if equipped) The anti-lock brake system automatically reduces or increases brake pressure as needed to provide optimum braking control, reducing the chance of wheel lock-up during hard braking events or when braking on rough, uneven, slippery or loose surfaces. See page 8. The anti-lock brake system cannot be turned off. The ABS indicator always illuminates when the key is in the ON or PARK position and

remains on until the anti-lock system activates, which occurs when vehicle speed exceeds 6 MPH (10 km/h).

When the lamp is illuminated, the anti-lock brakes will not activate, but the conventional brake system will continue to operate normally.

When the anti-lock brakes engage during a braking event, the rider will feel pulsing at the brake levers. Continue to apply steady pressure to the brakes for the best stopping perfor- mance.

If the ABS light does not come on when the key is turned to the ON or PARK position, see your authorized VICTORY dealer for service.

If the lamp continues to illuminate after vehicle speed exceeds 6 MPH (10 km/h), the ABS system is not functioning. See your VICTORY dealer promptly for service.

Operating with non-recommended tires or improper tire pressure may reduce the effec- tiveness of the anti-lock brake system. Always use the recommended size and type of tires specified for your vehicle. Always maintain the recommended tire pressure.

The anti-lock brake system will not prevent wheel lockup, loss of traction or loss of con- trol under all conditions. Always adhere to all safe motorcycle-riding practices as recom- mended.

It is not unusual to leave tire marks on the road surface during a hard braking event. The anti-lock brake system does not compensate for or reduce the risks associated with:

excessive speed reduced traction on rough, uneven or loose surfaces poor judgment improper operation

33

Instruments, Features and Controls Brakes The front brake lever activates the front brake calipers. The rear brake pedal activates the rear brake caliper. For maximum brake effectiveness, apply the front brake lever and the rear brake pedal together.

Front Brake Lever The front brake lever is located on the right handlebar. This lever controls only the front brakes. The front brakes should be applied simultaneously with the rear brakes. To apply the front brake, pull the lever toward the handle- bar. See page 51 for braking procedures. Front brake lever reach (distance to the hand grip) is adjustable. 1. Pull and hold the lever away from the hand grip. 2. To increase reach distance, rotate the adjuster to align a lower number with the arrow on

the lever. 3. To decrease reach distance, rotate the adjuster to align a higher number with the arrow on

the lever.

Rear Brake Pedal The rear brake pedal is located on the right side of the motorcycle. Press downward on the rear brake pedal to apply the rear brake. The rear brake pedal activates the rear brake caliper fully. See page 33 for pedal adjustment options. See page 51 for braking procedures.

Pedal Adjustment The brake pedal and gear shift pedal controls can be adjusted to a front, rear or center position. The center position is the factory setting. 1. Remove the screw from the footwell support.

Tool: 6 mm Allen wrench 2. Slide the control forward or rearward in its track

until the threaded hole of the control aligns with the desired hole in the footrest support.

3. Reinstall the screw. Torque: 96 in-lbs (11 Nm)

4. After adjusting the shift pedal, always readjust the shift linkage rod. Loosen both jam nuts on the linkage and turn the shaft until the footpeg is about 90 mm from the floor- board (or to desired height). Tighten both jam nuts. Torque: 96 in-lbs (11 Nm)

Front Brake Lever

Center Adjustment Position

34

Instruments, Features and Controls Tilt Sensor A tilt sensor stops the engine if the motorcycle tips beyond 45 degrees to one side. The check engine light or message will also activate. To restart the engine, cycle the ignition switch to the OFF position, wait 20 seconds, then restart the engine.

Sidestand The sidestand is located on the left side of the motorcycle. Sidestand Interlock Switch This vehicle is equipped with a sidestand interlock switch that prevents the engine from starting, although it will crank, if the sidestand is extended and the transmission is in gear. If this occurs, the check engine lamp will illumi- nate until the sidestand is retracted or until the transmis- sion is placed in neutral. The interlock switch error code will also display in the diagnostic screen. The SPN will read 520267 and the FMI will read 31. See page 26. Turn the ignition switch off to clear the code. Sidestand Operation To park the motorcycle, swing the end of the sidestand downward and away from the motor- cycle until it is fully extended. Lean the motorcycle to the left until the sidestand firmly sup- ports the motorcycle. To retract the sidestand, straddle the motorcycle and bring it to the fully upright position. Swing the end of the sidestand upward and toward the motorcycle until it is fully retracted.

35

Instruments, Features and Controls Storage Compartments (CROSS COUNTRY TOUR) A storage compartment is located at the top of each lower fairing. The maximum weight capacity for each compartment is five pounds (2.3 kg). Optional door locks are available for these compartments. The left compartment contains the iPod cord and a second 12-volt accessory outlet. To open a compartment door, pull the door handle and allow the door to pivot downward. Do not force a door to open beyond the door pivot stop.

Vent Handles

Vent Pivot Stop

12-Volt Outlet and iPod Cord

Door Handle

Deflector

36

Instruments, Features and Controls Fairing Vents and Deflectors (CROSS COUNTRY TOUR) An air vent and a deflector are located in each lower fairing. Use the vent handles to open and close the vents. Do not force a vent to open beyond the vent pivot stop. Move a deflector inward or outward to adjust air flow. WARNING! Failure to inspect deflector clearance after removing and reinstalling a fairing could result in steering interference, which could result in serious injury or death. After removing and reinstalling a fairing, always check for adequate steering clearance by moving the handlebars fully to the left and fully to the right, first with the deflectors open and again with the deflectors closed. Make any adjustments necessary to ensure steering clearance.

Passenger Floorboard Supports (CROSS COUNTRY TOUR) The passenger floorboard height and angle can be adjusted. To adjust the angle, loosen both attachment screws. Rotate the floorboard to the desired position using the indicator mark on the rear-facing support as a guide, then tighten the screws.

Torque: 18 ft-lbs (24.4 Nm) To adjust the height, remove both attachment screws. Move the floorboard assembly to the next hole position, then reinstall the fasteners, adjust the angle and tighten the fasteners to the recommended torque.

Attachment Screws

37

Instruments, Features and Controls Tool Kit The tool kit can be used to perform most basic mainte- nance items. Tools provided in the tool kit include: 1. 4 mm Ball Drive Allen Wrench 2. 5 mm Ball Drive Allen Wrench 3. 6 mm Ball Drive Allen Wrench 4. 4 mm / 6 mm Open End Wrench 5. 8 mm / 10 mm Open End Wrench 6. Combination Phillips / Slot Screw Driver 7. Rear Shock Absorber / Tire Pressure Gauge 8. Fuse Puller

License Plate The license plate module is equipped with an LED light to illluminate the license plate. Always make sure the license plate is properly installed before operating the motorcycle. 1. Position the license plate at the center of the rear fender, aligning the bottom edge of the

license plate to the fender mounting bracket. 2. Secure the license plate with appropriate fasteners. 3. If an accessory trunk is installed to the vehicle, the license plate mount must be installed

to the trunk to comply with regulations. Install the bracket and light assembly supplied with the accessory. Align the top edge of the license plate with the top edge of the license plate window. The fender license plate light must also be covered.

1 43

5

6 7

8

2

38

Pre-Ride Inspections To keep your motorcycle in safe operating condition, always perform the recommended pre- ride inspections before each ride. This is especially important before making a long trip and when removing the motorcycle from storage. WARNING! Failure to perform the recommended pre-ride inspections could result in component failure while riding, which could result in serious injury or death. Always perform the pre-ride inspections before each ride. When inspection reveals the need for adjustment, replacement or repair, perform the service promptly. You must be familiar with all instruments and controls to perform the pre-ride inspections. Tip: During the pre-ride inspections you may use products that are potentially hazardous, such as oil or

brake fluid. When using any of these products, always follow the instructions and warnings on the product packaging.

When inspections reveal the need for adjustment, replacement or repair: refer to the maintenance section of this manual refer to the service manual or see your authorized VICTORY dealer

39

Pre-Ride Inspections Turn the ignition key to the ON position and move the stop/run switch to RUN before per- forming the following electrical inspections. Return the ignition key to the OFF position after completing these inspections. If inspection of any electrical item reveals component failure, repair or replace the component before operating the motorcycle.

Item Inspection Procedure Electrical Headlamp Switch to high beam. Verify that the high beam indicator comes on and that

lamp brightness increases. Taillight/Brakelight Verify that the taillight and license plate light illuminate. Verify that the taillight

lamps increase in brightness when the front brake lever is applied and also when the rear brake pedal is applied.

Turn Signals Move the turn signal switch to the left. Verify that front and rear left turn signals flash, as well as the corresponding light on the indicator panel. Push the switch inward to cancel the signal. Verify that the signals and the indicator light stop flashing. Repeat the procedure for the right turn signals.

Emergency Flashers Press the top of the hazard switch to turn the flashers on. Verify that all four turn signals flash, as well as the lamps on the indicator panel. Turn the flashers off. Verify that all signals and indicator lamps stop flashing.

Horn Press the horn button. Verify that the horn sounds loudly. Neutral Indicator Place the transmission in neutral. Verify that the neutral indicator lamp illumi-

nates and that the letter N displays in the gear position display. CROSS COUNTRY Low Oil Pressure Indicator

Verify that the low oil pressure lamp illuminates. Start the engine and verify that the low oil pressure lamp goes off.

CROSS ROADS Low Oil Pressure Display

Start the engine. Verify that the low oil pressure display goes off in the multi- function display.

Engine Stop/Run Switch

Start the engine. Move the stop/run switch to the STOP position. Verify that the engine stops. Attempt to restart the engine to verify that the engine WILL NOT start.

General Engine Oil Level Check the oil level on the dipstick. Fuel Level View the fuel gauge or information bar. Tires Inspect condition, pressure and tread depth. Brake Operation Inspect pedal and lever movement. Brake Fluid Levels Check front and rear brake fluid levels. Brake Components Inspect hoses, connections, brake pads. Throttle Inspect hand grip and throttle freeplay. Clutch (Mechanical) Check lever operation and freeplay. Front Suspension Check for leaks, debris and damage. Steering Check for smooth operation. Rear Suspension Check shock movement and air pressure, verify ground clearance. Drive Belt Check for wear, damage, proper deflection. Sidestand Verify smooth operation, inspect pivot bolt, spring and pad. Fasteners Inspect for loose, damaged or missing fasteners. Mirrors Adjust for proper rear view.

40

Pre-Ride Inspections Engine Oil Level The oil fill cap/dipstick is located on the right side of the vehicle. Always use the recommended oil. See page 105. Tip: The engine must be at normal operating temperature

when checking the oil level. 1. Place the transmission in neutral. 2. Start the engine and allow it to idle for several min-

utes. 3. Stop the engine and wait 3-5 minutes before check-

ing the oil level. 4. On level ground, straddle the motorcycle and bring

it to the fully upright position. 5. Remove the oil fill cap/dipstick and wipe it

clean. Reinstall the dipstick and turn the cap clockwise until it seats.

6. Remove the dipstick and view the oil level. 7. Add or remove oil as needed to bring the

level into the safe operating range (between the FULL and ADD marks) on the dipstick.

WARNING! Operating the engine with too much or too little oil can cause serious engine damage or engine seizure, which could result in loss of control and serious injury or death. Do not operate the motorcycle with the oil level above the FULL mark or below the ADD mark.

Fuel Level 1. On level ground, straddle the motorcycle and

bring it to the fully upright position. 2. Turn the ignition switch to the ON or PARK

position. View the fuel level in the fuel gauge (CROSS COUNTRY), or use the MODE button to toggle to the fuel display in the information bar (CROSS ROADS).

3. Refuel as needed. See page 105 for fuel specifications.

Oil Fill Cap/Dipstick

Safe Range

{

Fuel Gauge (CROSS COUNTRY)

Fuel Bar (CROSS ROADS)

41

Pre-Ride Inspections Tires Tire Pressure Check tire pressure before riding, when the tires are cold. This will provide the most accurate reading, as riding warms the tires and increases tire air pressure. Adjust tire pressure as needed based on the total weight of your intended load. See page 80. Tire Condition Inspect the tire sidewalls, road contact surface and tread base. If inspection reveals cuts, punctures, cracks or other wear or damage, replace the tire before riding. Tire Tread Depth Measure the tread depth near the center of the tread on both tires. See page 79. Replace any tire with a tread depth of less than 1/16 (1.7 mm).

Front Brake Lever 1. Pull the front brake lever toward the

handlebar and hold it. The lever should move freely and smoothly. It should not move more than 3/4 inch (19 mm) before resistance is firm. It should con- tinue to feel firm, without loss of pres- sure, until the lever is released.

2. Release the lever. It should return to its rest position quickly when released.

3. If the front brake lever fails to perform as stated, service the brake lever before riding.

4. See page 33 for front brake lever reach adjustments.

Front Brake Fluid Level 1. Straddle the motorcycle and bring it to the fully upright position. Position the handlebars

so that the fluid reservoir is level. 2. View the fluid level through the sight glass. The fluid should be clear. Replace cloudy or

contaminated fluid. 3. The fluid level should be at or above the top of the sight glass. Add brake fluid if neces-

sary. See page 76.

Resistance at 3/4 inch (19 mm)

Minimum Level

42

Pre-Ride Inspections Rear Brake Pedal 1. Press downward on the rear brake pedal. It

should move freely and smoothly. It should not move more than 3/8 inch (8 mm) before resistance is firm. It should continue to feel firm, without loss of pres- sure, until the pedal is released.

2. Release the pedal. It should return to its rest position quickly when released.

3. If the rear brake pedal fails to perform as stated or travels too far before beginning to engage the brake, service the brakes before riding.

4. See page 33 for rear brake pedal adjust- ments.

Rear Brake Fluid Level The rear brake fluid reservoir is located near the rear brake pedal. View the reservoir from the front right side of the vehicle. 1. Position the motorcycle on level ground in the

fully upright position. 2. View the brake fluid through the reservoir. 3. The fluid should be clear. Replace cloudy or

contaminated fluid. 4. The fluid level should be between the minimum

and maximum marks on the reservoir. Add brake fluid as needed. See page 75.

Brake Lines Inspect all brake hoses and connections for damp- ness or stains from leaking or dried fluid. Tighten any leaking connections and replace components as necessary. Tip: Refer to the service manual or contact your dealer

for fastener torque values. WARNING! Brake fluid leaks or low brake fluid levels could cause brake system failure, which could result in serious injury or death. Do not operate the vehicle with low brake fluid levels or when leaks are evident (dampness or stains from dried fluid). See your VICTORY dealer for service.

Resistance at 3/8 inch (8 mm)

Maximum Mark

Minimum Mark

43

Pre-Ride Inspections Brake Pads Inspect each front brake pad on both sides of the front disc. Inspect each rear brake pad on both sides of the rear disc. When the thinnest point of the friction material has worn to the minimum recommended thickness, see your VICTORY dealer for brake pad replacement. Replace brake pads when friction material thickness reaches 1.0 mm. When checking brake pad friction material thickness, check each brake caliper for damp- ness or stains from leaking or dried brake fluid. If inspection reveals signs of fluid leakage, do not operate the vehicle. See your VICTORY dealer for service. See page 77 for brake disc inspection.

Throttle Rotate the throttle control grip. It should rotate smoothly from the rest position to the completely open position. It should return to the rest position quickly when released. Throttle Freeplay Throttle freeplay is the amount of throttle control grip movement from the rest position to the point of cable resistance. Measure this distance. Freeplay should be 2-4 mm. Adjust throttle freeplay as needed. See page 72.

Mechanical Clutch 1. Squeeze the clutch lever toward the handlebar

and release it. It should move freely and smoothly, and it should return to the rest posi- tion quickly when released. If the lever fails to perform as stated, service the clutch lever before riding.

2. Freeplay (gap) is the amount of lever movement from the rest position to the point of cable resis- tance. Clutch lever freeplay should be 0.5-1.5 mm. Measure the gap between the clutch lever and the lever housing. Adjust clutch lever freeplay if necessary. See page 73.

Tip: The starter interlock switch is dependent on the clutch lever freeplay being set correctly to ensure activation of the clutch safety switch.

Friction Material

Minimum: 1.0 mm

Front Rear

2-4 mm to resistance

Lever Housing

Clutch Lever0.5-1.5 mm

Freeplay

44

Pre-Ride Inspections Front Suspension Inspect the front forks for oil leaks or damage, and verify smooth suspension operation. See page 70.

Steering 1. On level ground, straddle the motorcycle and bring it to the fully upright position. Turn

the handlebars from stop to stop. The action should be smooth, but not loose. 2. Make sure wires, hoses and control cables do not interfere with smooth steering.

Rear Suspension 1. Check rear shock absorber movement and air pressure to ensure the correct amount of

suspension travel and ground clearance. 2. For air pressure adjustment information, see page 68 or refer to the suspension air pres-

sure label located in the left saddlebag near the air fitting. WARNING! Inadequate ground clearance could result in components contacting the ground, causing loss of control and serious injury or death. Always ensure ground clearance is at specification.

Drive Belt 1. Check drive belt tension. See page 65. The

drive belt should fit tightly. Tip: The drive belt system must be cool, clean and dry to

accurately measure belt tension (deflection). Do not measure belt tension when the belt or drive system is wet, or when it is hot (such as immediately after riding).

2. Check the drive belt teeth for stones or other debris.

3. Inspect drive belt condition. If you discover cracks, broken teeth or frayed edges, replace the drive belt before riding. See the VICTORY Service Manual or an authorized VICTORY dealer.

Drive Belt

45

Pre-Ride Inspections Sidestand 1. On level ground, straddle the motorcycle and bring it to the fully upright position. 2. Move the sidestand up to the stored position and down to the fully extended position sev-

eral times. It should move smoothly and quietly. Make sure the return spring holds the sidestand tightly in place when the sidestand is in the stored position. Adjust or replace a loose spring.

3. Inspect the sidestand pivot bolt for looseness or wear. Tighten or replace a loose or worn bolt.

4. Inspect the sidestand rubber pad. Make sure the pad is firmly attached to the sidestand. Check the wear indicator on the leading edge of the pad. Replace the pad when its worn beyond the wear limit line.

Fasteners 1. Inspect the entire motorcycle chassis and engine for loose, damaged or missing fasten-

ers. Tighten loose fasteners to the proper torque. Tip: Refer to the specifications section of this manual or the service manual for fastener torque values,

or see your VICTORY dealer. 2. Always replace stripped, damaged or broken fasteners before riding. Use genuine VIC-

TORY fasteners of equal size and strength.

Wear Limit Line

Front of Motorcycle

Pivot Bolt

46

Operation The operation section of this manual describes how to ensure maximum performance and longevity through the proper care and operation of your motorcycle. Tip: Even if you're an experienced motorcycle operator or passenger, read all of the safety information

in this manual before operating the motorcycle. See page 5. Important areas covered by the operation section include: Engine Break-In Fueling Starting the Engine Shifting Gears Accelerating Using Cruise Control (if equipped) Braking Stopping the Engine Parking

Engine Break-In The engine break-in period for your motorcycle is the first 500 miles (800 km) of operation. During this break-in period, critical engine parts require special wear-in procedures so they seat and mate properly. Read, understand and follow all break-in procedures to ensure the long-term performance and durability of your engine. NOTICE: Failure to properly follow the engine break-in procedures outlined in this manual can result

in serious damage to the engine. Follow all break-in procedures carefully. Avoid full throttle operation and other conditions that may place an excessive load on the engine during the break-in period.

Odometer Break-in Procedure

Miles Km 0-90 0-145 Do not operate for extended periods above 1/3 throttle or at any one throttle

position. Vary engine speed frequently. 91-300 146-483 Do not operate for extended periods above 1/2 throttle or at any one throttle

position. Vary engine speed frequently. 301-500 484-800 Do not operate for extended periods above 3/4 throttle.

At 500

At 800

Perform the break-in maintenance outlined in the maintenance section of this manual. Break-in maintenance should be performed by an authorized VIC- TORY dealer. Break-in maintenance must include inspection, adjustments, fas- tener tightening and an engine oil and filter change. Performing break-in maintenance at the required odometer reading helps ensure peak engine per- formance, minimal exhaust emissions and maximum service life of the engine.

47

Operation Fueling Always refuel on level ground with the sidestand down. Review the fuel warnings. See page 12. Use only the recommended fuel. See page 105. Hold the nozzle while filling. Do not rest the weight of the nozzle and hose on the filler neck. Do not leave the nozzle unattended. WARNING! Overflows or spilled gasoline could contact a hot engine or exhaust system and cause a fire, which could result in serious injury or death. Do not allow gasoline to contact hot components. 1. Insert the fuel nozzle into the fuel tank filler neck. 2. Fill the fuel tank to a level just below the bottom of the fuel filler insert. WARNING! Fuel expands in the fuel tank. Do not overfill. To prevent leaks, make sure the fuel filler cap is properly seated. 3. Always lock the fuel cap before riding. An open fuel cap could contact the handlebars. NOTICE: Fuel can damage painted surfaces and plastic parts. If gasoline spills on the any part of the

motorcycle, immediately rinse it off with water or wipe it dry with a clean cloth.

Priming the Fuel System If the motorcycle runs out of fuel, prime the fuel system before attempting to restart the engine. 1. Fill the fuel tank. 2. Turn the ignition key to the ON position. 3. Move the engine stop/run switch from the STOP position to the RUN position. 4. Allow the fuel pump to run until it stops (about 3 seconds). 5. Move the engine stop/run switch to the STOP position and wait 20 seconds. 6. Repeat steps 3-5 four to five times. 7. Turn the key to the OFF position. 8. Start the engine. See page 48.

48

Operation Starting the Engine The starter interlock system allows the engine to be started only when the transmission is in neutral, or when the transmission is in gear with the clutch disengaged (clutch lever pulled in) and the sidestand retracted. Tip: If the motorcycle runs out of fuel, prime the system before attempting to restart the engine. See

page 47. 1. Perform the Pre-Ride Inspections. See page 38. Properly secure any cargo. 2. Straddle the motorcycle and bring it to the fully upright position. 3. Retract the sidestand. 4. Insert the key into the ignition switch. Turn the key to the ON position. 5. Move the engine stop/run switch to the RUN position. You should hear the fuel pump

run momentarily as it pressurizes the fuel system. 6. If the neutral indicator is not illuminated, shift the transmission to neutral. 7. Apply the front brakes. 8. Leaving the throttle closed, press and hold the starter switch to start the engine. Release

the switch promptly when the engine starts. If the engine does not start within 10 sec- onds, release the starter switch. Wait five seconds, then try again.

Tip: Hold the starter switch for as short a time as possible to minimize battery drain. Do not hold the starter switch for more than 10 seconds at one time.

9. If either the check engine indicator or the low oil pressure indicator (or display) remains on after the engine starts, stop the engine immediately. Refer to either the check engine indicator information on page 25 or the low oil pressure indicator/display information on page 23 or 25.

10. Leave the throttle closed and allow the engine to idle. Idle speed will gradually slow to normal as the engine warms to operating temperature.

Tip: Do not rev the engine or put the transmission in gear immediately after starting the engine. Allow the engine to idle for about 30 seconds after a warm start or at least one minute after a cold start (longer in cold weather). This will allow oil to reach all areas before the engine is put under load.

49

Operation Shifting Gears WARNING! Forced shifting (with clutch engaged) could cause damage to the engine, transmission and drive train. Such damage could cause loss of control, which could result in serious injury or death. Always pull the clutch lever fully toward the handlebars to disengage the clutch before shifting gears. This motorcycle is equipped with a six-speed transmission. The sixth gear is overdrive. Neutral is located between first and second gear. Tip: The transmission is in neutral if you

can move the motorcycle forward or rearward freely without disengaging the clutch. If the ignition switch is in the ON position, the neutral indicator illu- minates when the transmission is in neutral.

1. Start the engine. See page 48. 2. With the engine at idle speed, apply the front brakes. 3. Disengage the clutch (pull the clutch lever fully toward the handlebar). 4. Push the shift pedal downward until you feel it stop in first gear. Tip: Shift to a higher gear by lifting the front of the gear shift pedal with your toe. Shift to a lower gear by

pressing the pedal downward. 5. Release the brake lever. 6. Simultaneously release the clutch lever while opening the throttle (rolling the throttle

control grip rearward) in one smooth motion. As the clutch begins to engage, the motor- cycle will move forward.

7. To shift to a higher gear, accelerate smoothly to the recommended shift point. See page 50. With a quick motion, simultaneously close the throttle completely and disengage the clutch. Raise the shift pedal until you feel it stop at the next gear. Simultaneously release the clutch lever and open the throttle in one smooth motion.

1

N

3 2

4 5 O/D

Neutral

Overdrive (6th Gear)

50

Operation Shifting Gears Tip: Within the recommended speed ranges (see Recommended Shift Points table), you can downshift

to slow the motorcycle or to increase power. You may want to downshift when climbing a hill or passing. Downshifting also helps to decrease speed when combined with closing the throttle.

8. To shift to a lower gear (downshift), simultaneously pull the clutch lever toward the han- dlebar and close the throttle. Move the shift pedal downward until you feel it stop at the next gear. Simultaneously release the clutch lever while opening the throttle.

WARNING! Downshifting improperly could cause transmission damage, loss of traction and loss of control, which could result in serious injury or death. Reduce speed before downshifting. Always downshift within the recommended shift points. Use extreme caution when downshifting on wet, slippery or other low traction surfaces. Release the

clutch lever very gradually in these conditions. Avoid downshifting in a curve. Downshift before entering the curve.

Recommended Shift Points

Accelerating Accelerate by opening the throttle (rolling the throttle control grip rearward). For even accel- eration, open the throttle with a smooth, continuous motion. When you reach the recom- mended speed for upshifting, shift up one gear. WARNING! Accelerating abruptly could cause your body to shift rearward suddenly, which could result in loss of control. Accelerating abruptly could also cause loss of control on low traction surfaces. Loss of control could result in serious injury or death. Always accelerate gradually, especially on wet, slippery or other low traction surfaces.

Upshifting (Accelerating) Downshifting (Decelerating) Gear Change Recommended Speed Gear Change Recommended Speed

1 to 2 18 MPH (29 km/h) O/D to 5 50 MPH (80 km/h) 2 to 3 30 MPH (48 km/h) 5 to 4 35 MPH (56 km/h) 3 to 4 40 MPH (64 km/h) 4 to 3 25 MPH (40 km/h) 4 to 5 50 MPH (80 km/h) 3 to 2 15 MPH (24 km/h)

5 to O/D 60 MPH (96 km/h) 2 to 1 10 MPH (16 km/h)

51

Operation Braking Always allow sufficient stopping distance so that brakes can be applied gradually. Tip: Applying slightly more front brake than rear brake generally provides the best braking perfor-

mance. 1. To slow the motorcycle with the brakes, close the throttle and apply the front and rear

brakes evenly and gradually. Tip: If the anti-lock brake system activates while braking (if equipped) youll feel pulsing at the foot

brake or hand brake. Continue applying equal pressure to the brakes to slow or stop the motorcy- cle. See page 8.

2. As the motorcycle slows, disengage the clutch, or downshift each time vehicle speed reaches a downshift point.

WARNING! Braking improperly could result in loss of control, which could result in serious injury or death. Avoid braking abruptly. Always apply the brakes gradually, especially on wet, slippery or other low traction surfaces. Avoid braking in a curve or turn. Bring the motorcycle to the upright position before applying the brakes.

Using Cruise Control (if equipped) If equipped, the cruise control is located on the right handlebar. Read this section and understand how to safely operate this fea- ture before using the cruise control. WARNING! Improper operation of cruise control could cause loss of control and result in serious injury or death. Follow all cruise operation procedures carefully. Never use cruise control when roads are wet or slippery. Do not use cruise control when riding in heavy or congested traffic.

Cruise Control Tips Cruise control can be set in any gear. Vehicle speed must be above 25 MPH (40 km/h). Set speed will vary slightly in hilly terrain. Cruise control will not resume a pre-set speed if the resulting

acceleration or deceleration rate is too high or too low. For example, resuming a set speed from 40 MPH (64 km/h) while in 6th gear may cause cruise to disengage.

Cruise control will not engage if brake lights are not operating properly.

Set Speed 1. Press the cruise control ON button. Tip: The cruise control indicator lamp will illuminate when the ON or

OFF switch is pressed. 2. Wait at least 3 seconds. A red dot (power indicator) at the

center of the switch will illuminate to indicate when cruise control can be engaged.

3. Accelerate to the desired speed and press the SET switch. The cruise control indicator lamp will illuminate.

Cruise Control Switches

ON SET

Power Indicator

52

Operation Using Cruise Control (if equipped) Resume Speed After disengaging the cruise control with the brake, throttle or clutch, wait at least 3 seconds, then press the resume but- ton (RES) to return to the set speed. If the resume button is pressed within 3 seconds of disengag- ing, the cruise control may not engage, even if the cruise con- trol indicator illuminates. This is a safety feature that prevents cruise control from engaging if a button is stuck. To continue using cruise control, disengage it. Wait at least 3 seconds, then press the resume button. Tip: Turning the cruise control master switch off will erase the set

speed from memory and disengage the cruise control.

Accelerate Tap and release the accelerate (ACC) button to increase speed in approximately 1 MPH (1-2 km/h) increments. Press and hold the ACC button to accelerate to a new SET speed (resets when button is released). Tip: If you use the throttle to accelerate and then release it, the cruise control will resume the previ-

ously set speed.

Decelerate Tap and release the decelerate (DEC) button to decrease speed in approximately 1 MPH (1-2 km/h) increments. Press and hold the DEC button to decelerate to a new SET speed (resets when button is released), or to the minimum cruise speed of 25 MPH (40 km/h).

Cancel Cruise Control To temporarily cancel the cruise control and allow use of the resume feature: apply the brakes or close the throttle or disengage the clutch To cancel the cruise control and erase the set speed from memory, press OFF.

Resume

Accelerate

Off Decelerate

53

Operation Stopping the Engine Before stopping the engine, bring the motorcycle to a complete stop. Shift to neutral or dis- engage the clutch. WARNING! Stopping the engine with the transmission in gear while the motorcycle is moving could cause loss of rear wheel traction or engine and transmission damage, which could cause loss of control and serious injury or death. Always stop the engine after the motorcycle is fully stopped and the transmission is in neutral. If the engine stops unexpectedly while the motorcycle is moving, guide the motorcycle to a safe location off the road and away from traffic. 1. When fully stopped, shift into neutral. 2. Move the engine stop/run switch to the STOP position. 3. Move the ignition switch to the OFF position. Remove the ignition key. Tip: A momentary clicking sound from the IAC valve is normal when the key is first turned to the OFF

position.

Parking Choose a firm level surface to park the motorcycle. 1. When fully stopped, shift into neutral. 2. Stop the engine. 3. Fully extend the sidestand. 4. Turn the handlebars to the left and lean the motorcycle to the left until the sidestand

firmly supports the motorcycle. 5. Remove the ignition key.

Parking on a Slope If parking on a slope is unavoidable, position the front of the motorcycle toward the top of the slope. Place the transmission in gear and position the motorcycle so that it is stable when it rests on the sidestand.

Parking on a Soft Surface If parking on a soft surface is unavoidable, place a sidestand footrest under the foot of the sidestand to provide a firm surface. The sidestand footrest must be strong enough and large enough to support the motorcycle's weight without sinking into the parking surface. Asphalt becomes soft in hot weather. A sidestand can sink into soft asphalt and the motorcy- cle may fall. When parking on asphalt in hot weather, use a sidestand footrest. CAUTION! Hot engine and exhaust components can cause burns to skin and can ignite a fire if exposed to flammable materials. Always park the motorcycle clear of flammable materials and where people are not likely to contact hot components.

54

Operation Reverse Operation (if equipped) NOTICE: Do not attempt to engage or disengage the reverse system when the motorcycle is moving.

Before Operating in Reverse: always sit on the motorcycle with legs astride and both feet on the ground. always check for obstacles or people behind the motorcycle. always retract the sidestand fully. always make sure the motorcycle is completely stopped. NEVER Operate in Reverse: when not properly seated. when in an area where obstacles or bystanders are present. with a passenger on board. A passenger can obstruct your view and maneuverability. when on loose or slippery surfaces. Loss of foot traction could cause a tip-over. while the motorcycle is moving forward. when on a grade or uneven surfaces. Reverse Operation Procedure 1. Always check for obstacles or people behind the motorcycle. Be aware that the front

wheel may travel outward and require a larger operating area. 2. Make sure the motorcycle is stationary. 3. Dismount any passenger. 4. Sit on the operators seat with legs astride and both feet on the ground. 5. Retract the sidestand (if down). 6. Place the transmission in neutral. 7. With the engine idling, lift the reverse lever and verify that the reverse indicator (R) dis-

plays in the multi-function display. NOTICE: NEVER shift the transmission into gear with the reverse engaged. Doing so WILL result in

damage to the reverse system. 8. Recheck the area behind and around the motorcycle to ensure a clear operating area. 9. While balancing the motorcycle with your legs and feet, press and hold the starter switch

to begin moving in reverse. Release the switch to stop moving. NOTICE: NEVER shift the transmission into gear with the reverse engaged. Doing so WILL result in

damage to the reverse system. 10. If parking the motorcycle, wait until its completely stopped, then move the reverse lever

down to the disengaged position. Verify that the neutral indicator (N) displays before stopping the engine.

55

Maintenance Safety During Service Procedures

Failure to follow recommended precautions and procedures could result in severe injury or death. Always heed all safety precautions and follow all operation, inspection and maintenance procedures outlined in this manual. Improperly installed or adjusted components can make the motorcycle unstable or hard to handle.

Improperly installed electrical components can cause engine or electrical system failure. In either event, damage or serious injury could result. If you do not have the time, tools and expertise necessary to complete a procedure properly, please see your dealer for service.

Review the safety-related maintenance information on page 13. Before beginning any maintenance procedure, read the instructions for the entire procedure. Always position the motorcycle on a firm level surface before performing service. Make sure the

motorcycle will not tip or fall while elevated or while on the sidestand. Hot engine and exhaust components can cause burns to skin and can ignite a fire if exposed to

flammable materials. Always park the motorcycle clear of flammable materials and where people are not likely to contact hot components.

Wear eye and face protection when using pressurized air. Never start the engine or let it run in an enclosed area. Engine exhaust fumes are poisonous and

can cause loss of consciousness or death in a short time. During some procedures you may use potentially hazardous products such as oil or brake fluid.

Always follow the instructions and warnings on the product packaging.

WARNING

56

Maintenance Proper maintenance assures the highest level of safety, durability and dependability for your motorcycle. Have your VICTORY dealer perform the break-in maintenance procedures when the

motorcycles odometer registers 500 miles (800 km). Perform the recommended periodic maintenance at the intervals specified in the periodic

maintenance table beginning on page 57.

Road Tests Before returning the motorcycle to regular use after performing service, road test it in a safe environment. Pay special attention to the proper fit and operation of all serviced components. Make any corrections or additional adjustments necessary to ensure safe vehicle perfor- mance.

Break-In Maintenance Have your VICTORY dealer perform the break-in maintenance procedures when the motor- cycles odometer registers 500 miles (800 km). Performing the break-in maintenance will help ensure optimum engine performance for the entire service life of the engine. Your dealer will change engine oil, inspect all fluids and serviceable components, ensure that all fasten- ers are tightened and make other adjustments as needed.

Major Maintenance For major repair information, refer to the VICTORY Service Manual. Major repairs typically require technical skills and specially designed tools. Emission system service requires spe- cial tools and training and should be performed by your dealer.

Periodic Maintenance Inspect, clean, lubricate, adjust and replace parts as necessary. When inspection reveals the need for replacement parts, use genuine VICTORY parts available from your VICTORY dealer. Record service and maintenance information in the Maintenance Log beginning on page 58. Perform maintenance at the intervals specified in the periodic maintenance table beginning on page 57. Perform the procedures more frequently if normal use of the motorcycle includes: high speed operation for extended periods low speed operation for extended periods operation in dusty or otherwise adverse conditions

57

Maintenance Periodic Maintenance Table

See table key below

Component Page

Odometer Reading in Miles (Kilometers)

50 0

(8 00

)

50 00

(8 00

0)

10 00

0 (1

60 00

)

15 00

0 (2

40 00

)

20 00

0 (3

20 00

)

25 00

0 (4

00 00

)

30 00

0 (4

80 00

)

35 00

0 (5

60 00

)

40 00

0 (6

40 00

)

45 00

0 (7

20 00

)

50 00

0 (8

00 00

)

Air Filter 60 I I R I R I R I R I R Battery 81 I I I I I I I I I I I Brake Fluid 76 I I I I I I R I I I I Brake Pads 43 I I I I I I I I I I I Clutch Cable 74 I I L I L I L I L I L Clutch Lever (Mechanical)

73 74 L I L I L I L I L I L

Control Cables 73 74 I I L I L I L I L I L Crankcase Vent 71 I I I I I I I I I I I Drive Belt 64 I I I I I I R I I I I Drive Belt Adjustment 67 P Adjust with each tire change thereafter Engine Oil & Filter* 59 R R R R R R R R R R R Exhaust System 89 I I I I I I I I I I I Fasteners 90 I I I I I I I I I I I Front Brake Lever 76 L L L L L L L L L L L Front Fork Oil** 70 I I I R I I R I I R I Front Fork / Axle 70 I I I I I I I I I I I Fuel System 71 I I I I I I I I I I I Fuel Filter - Please see your dealer for this service. R Headlamp 86 I I I I I I Ignition Switch / Locks 82 L L L L L L L L L L Radio/Radio Software 106 Update annually. Please see your dealer. ABS Components 78 I I I I I I I I I I I Rear Wheel Align 67 I I I I I I I I I I I Rear Shock 68 I I I I I I I I I I I Rear Brake Pedal 75 I I L I L I L I L I L Road Test 90 P P P P P P P P P P P Sidestand 82 I I L I L I L I L I L Sidestand Pad 45 I I I I I I I I I I I Spark Plugs 80 I I I I I I R I I I I Steering Head Bearings 70 I I I L I I L I I L I Swingarm 69 I I I I I I I I I I I Throttle Cable 72 I I L I L I L I L I L Tires 79 I I I I I I I I I I I Wheel Spokes 78 I I I I I I I I I I I Wheel Condition 78 I I I I I I I I I I I Maintenance Key: I = Inspect, clean, adjust, correct or replace if necessary; P = Perform; R = Replace / Rebuild L = Lubricate w/ proper lubricant; * = Replace at specified interval or annually; ** = Replace as specified or every 2 years

58

Maintenance Maintenance Log

Maintenance Performed Miles / Km Notes Performed by

59

Maintenance Engine Oil / Filter Change Change the engine oil at the intervals specified in the peri- odic maintenance table beginning on page 57. 1. Start the engine and allow it to idle for several min-

utes. Stop the engine. Tip: The engine must be at normal operating temperature before

changing the oil. CAUTION! Hot engine and exhaust components can cause burns to skin and can ignite a fire if exposed to flammable materials. Always park the motorcycle clear of flammable materials and where people are not likely to contact hot components. 2. Position the motorcycle securely on the sidestand. 3. Place a drain pan under the drain plug and oil filter. Remove the drain plug and seal.

Allow the oil to drain completely. Tool: 6 mm Allen wrench

4. Slowly loosen the oil filter. Allow the oil to drain completely. Tool: 2 1/2 inch (63.5 mm) oil filter wrench

5. Clean the drain plug sealing surface on the crankcase. Reinstall the drain plug with a new seal. DO NOT overtighten. Torque: 15 ft-lbs (20 Nm)

6. Clean the oil filter mounting threads and gasket sealing surface on the crankcase. Make sure the new oil filter gasket is properly seated in the new oil filter. Apply a thin film of clean engine oil to the gasket. Screw the new filter on until the gasket contacts the seal- ing surface. Tighten the filter by hand an additional 3/4 turn.

7. Remove the oil fill cap/dipstick. Add approximately 4.5 quarts (4.25 liters) of the recom- mended oil. Reinstall the oil fill cap.

NOTICE: Do not add chemical additives to the engine oil. Some automotive engine oils contain additives that could damage or reduce the service life of the wet clutch in your motorcycle.

8. Start the engine and allow it to idle for several min- utes. Stop the engine.

NOTICE: After an oil change, the low oil pressure indicator or display remains illuminated longer than usual before going out. Revving the engine while the low oil pressure indicator or display is illuminated can damage the engine.

9. Check for leaks around the drain plug and oil filter. 10. Check the oil level and adjust if needed. 11. Recycle the used oil and filter properly.

Engine Oil Capacity at Oil Change (including filter)

4.5 qt. (4.25 liter) (approximately)

Engine Oil Capacity at Oil Change (not including filter)

4.0 qt. (3.8 liter) (approximately)

Drain Plug Oil Filter

1 qt. (.9 l) (approximately)

Oil Check/Fill

60

Maintenance Air Filter Inspect the air filter often if riding in unusually wet or dusty conditions. Do not apply air filter oil to this air filter. The fuel line is secured to the main wiring harness with a cable tie. Do not cut or remove the cable tie. 1. Remove the fuel tank. See pages 60-61. 2. Loosen the three filter retainer screws. 3. Loosen the two air filter mounting screws only until the

filter can be removed. Do not remove the screws from the filter.

4. Lift the retainer. Remove the filter by pulling upward and rearward.

5. Clean the filter sealing surface on the frame. 6. Install the new air filter with captive screws. Check the

edges of the filter to be sure they are seated properly in the flange.

7. Tighten the mounting screws, then tighten the retainer screws. Torque: 36 in-lbs (4 Nm)

8. Reinstall the fuel tank. See page 62.

Fuel Tank Removal A special fuel tank fitting plug tool is required for this pro- cedure. Please see your dealer to obtain this tool. Before beginning, be prepared to place the fuel tank in a secure location to avoid scratching the finish. 1. Remove both side covers and the seat. See pages 84

and 86. 2. Disconnect the fuel tank vent line. 3. Remove the ground wire bolt and rear tank bolts, along

with the bushings and isolators. Set hardware aside for reassembly.

4. Place the handlebars in the straight ahead position. Cover the front of the fuel tank with a protective cloth to prevent damage.

Mounting Screws

Retainer Screws

Step 2 Vent Line

Ground Wire Bolt

Tank Bolts

Step 3

61

Maintenance Fuel Tank Removal 5. The fuel line is secured to the main wiring har-

ness with a cable tie. Do not cut or remove the cable tie. Pivot the rear of the tank upward to access the tank bottom. Support the rear of the tank in this position.

6. Locate the pump harness electrical connector under the tank. Carefully lift the tab and discon- nect the harness.

7. If servicing the air filter, skip this step. If install- ing a new tank or servicing the fuel pump, dis- connect the vent and drain lines at the bottom of the fuel tank.

8. Disconnect the fuel line from the fuel pump by squeezing both fitting release tabs simultane- ously. Gently slide the fuel line off the fitting.

9. Install the fuel tank fitting plug tool onto the fuel pump fitting to protect the fitting and prevent fuel from seeping from the tank.

NOTICE: DO NOT rest the fuel tank on the frame while removing it. Fuel pump fitting damage can occur.

10. Lift the rear of the fuel tank as high as clearance at the front of the tank will allow to ensure ade- quate clearance for the fuel line fitting under the tank.

11. With the rear of the fuel tank raised, carefully slide the tank rearward and off the front mounts. When the tank is clear of the front mounts, lift the tank up and away from the frame. Reinstall the front isolators if they become dislodged.

Step 6 Lift tab to disconnect.

Step 8 Squeeze tabs.

Step 7 Vent Line Drain Line

Step 9

62

Maintenance Fuel Tank Installation 1. Place the handlebars in the straight ahead posi-

tion. Cover the front of the fuel tank with a pro- tective cloth to prevent damage.

2. Using care to avoid damage to the fuel tank fit- ting and special tool, position the fuel tank on the frame of the motorcycle.

3. If removed, reinstall the fuel tank vent and drain lines at the bottom of the tank. Rotate the lines against the side of the tank. Torque: 20 in-lbs (2.3 Nm)

4. Make sure the front isolators are installed to the frame. Apply alcohol, soapy water or rubber lubricant to ease tank installation.

5. Slide the tank onto the isolators, then slide the tank fully forward. Pivot the rear of the tank upward to access the tank bottom. Support the rear of the tank in this position.

6. Remove the plug tool from the fuel pump fitting by pressing the center button of the plastic coupler.

7. Carefully connect the fuel line to the fuel pump fitting. Make sure you hear a click to indicate proper engagement. Test the connection by pulling the fuel line lightly.

8. Connect the fuel pump harness electrical connector. 9. Verify that the fuel line is correctly routed and secured.

Step 3

Vent Line

Drain Line

63

Maintenance Fuel Tank Installation 10. Install the rear isolators (with flange side toward

the tank) and flange bushings. 11. Lower the tank and install the tank bolts.

Torque: 18 ft-lbs (24 Nm) 12. Connect the vent line, ground wire and ground

wire bolt. Torque: 96 in-lbs (11 Nm)

13. Prime the fuel pump. See page 47. 14. Check for leaks. 15. Reinstall the seat and side covers.

Isolators

Step 10

Step 12 Vent Line

64

Maintenance Drive Belt Condition Replace the drive belt if it is cracked or has bro- ken teeth or frayed edges. No matter its condition, the drive belt should be replaced at periodic inter- vals. See the VICTORY Service Manual or an authorized VICTORY dealer. DO NOT attempt to check belt tension if the belt has been exposed to rain or washing within a 24 hour period or if the belt is hot from riding. Allow the belt to cool down to ambient temperature before measuring belt tension. Replace the drive belt and both sprockets as a set if the drive belt has over 5,000 miles (8,000 km) of service at the time of damage or failure.

Drive Belt Wear Analysis

Internal tooth cracks (hairline):

OK to run, but monitor condition

External tooth cracks: Replace belt

Missing teeth: Replace belt

Chipping (not serious): OK to run, but monitor

condition

Fuzzy edge cord: OK to run,

but monitor condition

Hook wear: Replace belt

Stone damage: Replace belt if damaged

Bevel wear (outboard edge only):

OK to run, but monitor condition

65

Maintenance Drive Belt Tension Data Specifications are listed below for deflection and sonic tension. Sonic tension measurement requires Gates Sonic Tension Meter 507C or an equivalent. Drive Belt Deflection (Using PV-43532 Tension Gauge)

Drive Belt Sonic Tension (Using Sonic Tension Meter)

Drive Belt Tension Inspection On new drive systems or belt, adjust belt tension after the first 500 miles (800 km). Adjust tension at each tire change thereafter. Tip: Do not inspect or adjust drive belt tension when the belt is

wet. Improper adjustment will result. Checking drive belt tension involves using the belt tension gauge (P/N PV-43532). You can also use a Sonic Tension Meter if available. Before beginning this procedure: Make sure the drive system is clean, dry, and at room

temperature (belt and sprockets). Be sure suspension is properly adjusted. Belt tension must be adjusted at the tightest spot.

Deflection CROSS ROADS CROSS COUNTRY 32 mm 0.5 mm 32 mm 0.5 mm

Required Data Sonic Tension

CROSS ROADS CROSS COUNTRY Span 708.6

20 Hz 1 20 Hz 1Belt Width 28 mm Belt Mass Constant 8.4

Belt Tension Gauge

Small O-Ring

Base

Plunger

66

Maintenance Drive Belt Tension Inspection 1. Elevate and support the motorcycle with the rear tire

slightly off the floor. CAUTION! Make sure the motorcycle is stable when elevated. Injury may occur if the motorcycle tips or falls. 2. Place the transmission in neutral. 3. Rotate the rear wheel in a forward direction until the

valve stem is at the bottom. This is your reference point for determining the tight spot to make your adjustment (if necessary).

4. Position the small O-ring on the tension gauge directly over the 10 lbs. mark on the plunger.

5. Place a tape measure or steel rule next to the drive belt, mid-way between the sprockets. Support the rule or tape so it does not move.

6. Note the graduation mark on the rule that aligns with the lower edge of the belt. This position represents zero force.

7. Place the support base of the tension gauge squarely against the lower surface of the belt as close as possible to the rule or tape.

8. Keeping the tension gauge perpendicular to the belt sur- face and parallel with its length, push the plunger upward until the small O-ring touches the tension gauge body.

9. Be sure the tension gauge is seated squarely against the belt, and note the graduation mark on the rule that now aligns with the lower edge of the belt. This position rep- resents 10 lbs. force.

10. To calculate belt tension (deflection) subtract the smaller measurement from the larger measurement and record it.

Determine The Tightest Spot 11. Repeat the above deflection measurements

with the tires valve stem at the rear most posi- tion, top, and front most positions (90 degrees rotation each time), recording each measure- ment.

12. If the tightest measurement is not within the recommended range (see page 65), belt tension must be adjusted.

Belt Tension Gauge

Rule

Drive Belt

Push Inner Plunger

90 Drive Belt

90

90

90

Valve Stem

Rear Wheel

67

Maintenance Drive Belt Tension Adjustment 1. Move the wheel to the tight spot location

determined previously. 2. Loosen the rear axle nut on the left side. 3. Turn each axle adjuster nut clockwise an

equal amount to tighten the belt (reduce deflection) or an equal amount counter- clockwise to loosen the belt (increase deflec- tion). Tool: 13 mm deep socket

4. Tighten the rear axle nut. Torque: 65 ft-lbs (88 Nm)

5. Pump the rear brake pedal to re-set the pads against the brake disc.

6. Verify proper belt tension and wheel alignment.

Drive Belt / Rear Wheel Alignment 1. Look at the alignment reference

marks on each side of the swingarm and the marks on the axle plates to verify proper wheel alignment. Axle plate mark to reference mark align- ment must be the same on both sides.

2. If the marks are not aligned, perform all steps of the Belt Tension Adjust- ment procedure. See page 67.

3. Before and after tightening the axle nut, verify proper belt tension and wheel alignment.

Drive Belt Cleaning Cleaning the drive belt will maximize belt and sprocket life and minimize drive line noise. Clean the belt at every tire change. Clean the belt more often if riding in dirty, dusty or high debris environments. 1. Mix a few drops of mild dish soap with a cup of warm water. 2. Use a soft nylon brush to clean the belt and sprocket teeth with the soapy water. Clean

well in corner areas where road debris and belt dust can collect. 3. Rinse the belt with clear water, then dry thoroughly. Tip: Do not inspect or adjust drive belt tension when the belt is wet. Improper adjustment will result.

Axle Nut (hidden by swing arm)

Adjuster Nut

Axle Plate Marks

Swing Arm Marks

68

Maintenance Rear Suspension Adjustment For riding comfort and to ensure proper ground clear- ance, adjust rear shock air pressure as specified on the label located in the right saddlebag cover (reproduced below). Follow these guidelines when adjusting: Park the motorcycle with the sidestand down on a

firm, level surface. Remove all riders and cargo. DO NOT exceed 72 PSI (496 kPa) in the shock. Use the VICTORY Air Pump and Gauge (P/N

2876654). Follow the instructions on the following pages.

If the VICTORY air pump and gauge are not available, use the gauge provided in the tool kit, and a pressurized air source with a maximum line pressure of 72 PSI (496 kPa). After using this gauge, remove it quickly to minimize leakage. Expect to lose about 4 PSI (27.6 kPa) with each pressure check when using this gauge. Use only a dry air source, such as a system with a water separator or air line dryer, to prevent moisture from entering the shock. CAUTION! Air pressure increases VERY quickly when using pressurized air. Wear eye and face protection.

Air Suspension Adjustment (Shock Label)

Set desired pressure with bike unloaded on side stand

Total Cargo & Occupant Weight

(lbs)

Air Pressure (psi) No Trunk Trunk Tour

100 0 0 0 125 0 0 0 150 0 0 9 175 0 9 15 200 0 15 25 225 9 25 29 250 15 29 34 275 25 34 39 300 29 39 45 325 34 45 52 350 39 52 58 375 45 58 65 400 52 65 70 425 58 70 72 450 65 72 72 475 70 72 72 500 72 72 72

Shock Label

69

Maintenance Rear Suspension Adjustment 1. Park the motorcycle with the sidestand

down on a firm, level surface. Remove all riders and cargo.

2. Remove the right side cover.Remove the cap from the air fitting.

3. Refer to the shock label to determine the recommended air pressure.

4. Install the hose fitting of the recommended gauge securely onto the air fitting. Read the air pressure on the gauge.

Tip: A small oil leak from the air fitting is acceptable when pressure is adjusted. See your dealer if more than 5 cc of oil leaks from the fitting.

5. To reduce air pressure, push the bleed button on the gauge. Bleed pressure in small amounts until the desired pressure is attained.

6. To increase pressure, pump the handle until pressure increases to the desired amount. CAUTION! DO NOT exceed 72 PSI (496 kPa) in the shock. 7. Remove the hose from the air fitting and reinstall the cap.

Swing Arm / Rear Axle Inspection 1. Sit in the operator's seat and slowly bounce the rear suspension a few times. Make sure

the suspension moves freely without binding. Listen for abnormal noises. 2. Elevate and support the motorcycle with the rear tire slightly off the floor. CAUTION! Make sure the motorcycle is stable when elevated. Injury may occur if the motorcycle tips or falls. 3. Grasp the rear-most surface of the rear tire and attempt to move the wheel side-to-side. If

there is movement at the front of the swingarm, check the swingarm pivot nut torque and swingarm pivot bearings.

4. Contact your VICTORY dealer for service if you detect noise or movement at the swing- arm pivot.

5. Grasp the top or bottom surface of the tire and try to move it side to side. If there is movement at the rear axle, inspect wheel bearings and rear axle nut torque.

6. Contact your VICTORY dealer for service if you detect noise or movement at the wheel bearings.

7. With the transmission in neutral, slowly rotate the rear wheel. If the wheel does not rotate smoothly, inspect the wheel bearings, rear axle, belt adjust- ment and wheel alignment. See the VICTORY Ser- vice Manual or your authorized VICTORY dealer.

Air Fitting

Check for movement in wheel bearing area

70

Maintenance Front Fork / Suspension Inspection 1. Place the motorcycle on the sidestand and inspect the front

forks. If fork oil is present on the outer tube, do not ride the motorcycle. See your dealer for service before operating. If fork oil is present around the fork seals or inner tubes, replace the fork seals.

2. Clean the fork tubes to remove bugs, tar or buildup which may cause seal wear or leakage. Inspect the outer surfaces of the inner fork tubes for scratches or damage from foreign objects.

3. Straddle the motorcycle and bring it to the fully upright posi- tion. Apply the front brake and push downward (hard) on the handlebars several times. The front suspension should operate smoothly and quietly.

4. Fork oil condition and level affects front suspension perfor- mance and internal component wear. Replace fork oil at the recommended intervals. Special tools are required to perform this procedure. See the VICTORY Service Manual or your authorized VICTORY dealer.

Steering Head Inspection 1. Elevate and support the motorcycle with the

front tire slightly off the floor. CAUTION! Make sure the motorcycle is stable when elevated. Injury may occur if the motorcycle tips or falls. 2. Turn the handlebars from stop to stop. The

action should be smooth but not loose. Make sure wires, hoses and control cables do not inter- fere with smooth steering.

3. Position the front wheel straight ahead. Grasp the front forks near the front axle and attempt to move the wheel front-to-back. If there is front- to-back movement at the steering head, see your VICTORY dealer for service.

Fork Inner Tube

71

Maintenance Fuel System Components 1. Inspect fuel hoses for cracks or damage. 2. Inspect hose connections at the fuel tank and at the fuel rail for dampness or stains from

leaks.

Fast Idle A fast idle speed during warm up of between 1200 and 2000 RPM is automatically set by the EFI system Idle Air Control (IAC). Periodic adjustment is not required.

Crankcase Breather Hose Inspect the crankcase breather hose for cracks or damage. Be sure the clamps are in place and secure.

Breather Hose

72

Maintenance Throttle Control Inspection 1. With the engine OFF, rotate the throttle control

grip fully open and then release it. It should rotate smoothly from the rest position to the completely open position. It should return to the rest position quickly when released.

2. Repeat the twist and release process with the han- dlebars turned fully right and fully left.

NOTICE: To prevent damage to the throttle system, always operate with the throttle cable guard installed.

3. Remove the right side access cover. 4. Inspect throttle cables for frayed ends. 5. Service the throttle system if throttle operation is

not smooth, if throttle grip does not return prop- erly, or if cable ends are frayed. See the VICTORY Service Manual or your authorized VICTORY dealer.

Throttle Cable Freeplay Throttle freeplay is the amount of throttle control grip movement from the rest position to the point of cable resistance. Measure this distance. Freeplay should be 2-4 mm. Adjust throttle freeplay as needed. 1. Position the front wheel straight ahead. Stop the

engine. 2. Hold the adjuster nuts securely and loosen the lock

nuts on both cables. Turn the lock nuts away from the adjuster nuts as far as possible.

3. Turn both adjuster nuts toward the lock nuts as far as possible for maximum freeplay in both cables.

4. Turn the adjuster on the throttle opening cable (front cable) away from the lock nut until throttle freeplay is 2-4 mm.

5. To adjust the closing cable (rear cable), hold the throttle grip lightly in the closed position. Turn the adjuster slowly outward until slight resistance is felt.

6. Turn the lock nuts on both cables until they are seated against the adjuster nuts. Hold each adjuster nut and tighten each lock nut securely.

7. Repeat the throttle control inspection. See page 72.

Cable Area

Throttle Cable Guard

Lock NutAdjuster Nut

2-4 mm to resistance

73

Maintenance Cruise Control Cable Inspection (if equipped) 1. Remove the right side access cover. 2. Inspect the throttle body end of the cruise control

cable for fraying and be sure the end is secured in the bracket.

Throttle Cable Lubrication Lubricate control cable ends at the intervals recom- mended in the periodic maintenance table beginning on page 57. NOTICE: External casings are factory-lubricated. Additional lubrication could be detrimental to cable

performance. Verify proper routing and smooth movement. Inspect for damage to the external casing, and inspect exposed cable wire for fraying, kinks or corrosion. Replace any damaged, sticky or sluggish cable. 1. Disconnect the cable at the throttle body. 2. Apply a light film of VICTORY All Purpose Grease or equivalent to the barrel end. 3. Reconnect the cable and adjust freeplay as needed.

Mechanical Clutch Lever Freeplay 1. Remove the right side access cover. 2. Hold the clutch cable and loosen the adjuster lock

nut. 3. While holding the cable, turn the cable adjuster

inward or outward until clutch lever freeplay is 0.5-1.5 mm.

4. While holding the cable, tighten the adjuster lock nut securely.

5. Reinstall the right side cover. 6. Verify that the safety switch activates properly. The engine should not start in gear with

the clutch lever released. Tip: The starter interlock switch is dependent on the clutch lever freeplay being set correctly to ensure

activation of the clutch safety switch.

Cruise Control Cable

0.5-1.5 mm Freeplay

74

Maintenance Mechanical Clutch Lever Lubrication 1. Remove the right side access cover. Loosen the clutch

cable adjuster lock nut. 2. Turn the cable adjuster completely inward to provide

maximum lever freeplay. 3. Remove the clutch lever pivot nut and screw. Disconnect

the clutch cable from the clutch lever. 4. Remove any old grease and dirt from the lever and hous-

ing. Lubricate the clutch lever and pivot screw with VIC- TORY Moly Assembly Grease or VICTORY All Purpose Grease.

5. Reconnect the clutch cable. Reinstall the lever, pivot screw and nut. Hold the screw down and tighten the nut. Torque: 40 in-lbs (5 Nm)

6. Adjust clutch lever freeplay. See page 73.

Mechanical Clutch Cable Lubrication Lubricate control cable ends at the intervals recommended in the periodic maintenance table beginning on page 57. NOTICE: External casings are factory-lubricated. Additional lubrication could be detrimental to cable

performance. Verify proper routing and smooth movement. Inspect for damage to the external casing, and inspect exposed cable wire for fraying, kinks or corrosion. Replace any damaged, sticky or sluggish cable. 1. Disconnect the cable at the clutch lever and at the primary cover. 2. Lubricate the barrel ends with VICTORY All Purpose Grease or equivalent. 3. Reconnect the cable and adjust freeplay as needed.

Pivot Nut

Pivot Screw

75

Maintenance Rear Brake Pedal 1. See page 33 for rear brake pedal adjustments. 2. Lubricate the pivot bushing at the intervals recommended in the periodic maintenance

table beginning on page 57. Also lubricate any time binding is evident. Use VICTORY All Purpose Grease or equivalent.

3. Inspect brake pads as outlined on page 43.

Brake Fluid Precautions

Using the wrong fluid or allowing air or contaminants into the fluid system can damage the system seals or result in a malfunction that could lead to serious injury or death. Use only DOT 4 brake fluid from a sealed container. Do not operate the front brake with the reservoir cover removed. Fluid could overflow from the reservoir and allow air to enter the system. Air in the brake system could cause the brakes to malfunction. An over-full reservoir may cause brake drag or brake lock-up, which could result in serious injury or death. Maintain brake fluid at the recommended level. Do not overfill.

NOTICE: Brake fluid will damage painted surfaces and plastic parts. Always clean spilled brake fluid immediately with water and a mild detergent.

Rear Brake Fluid 1. Position the motorcycle on level ground in the fully

upright position. 2. The rear brake fluid reservoir is located near the rear

brake pedal, just inside the right lower leg fairing. Wipe the fluid container and the area around the reservoir cover with a clean cloth.

3. If the fluid level is low, inspect brake pads as outlined on page 43. If pads are not worn beyond the service limit, inspect the brake system for leaks.

4. To add fluid, remove the reservoir cover. Carefully add fluid to the recommended level. Do not overfill.

5. Reinstall the cover and diaphragm. 6. Wipe away any fluid spills. Check for signs of brake

fluid leaks around hoses, fittings, reservoir, and brake calipers.

WARNING

Maximum Mark

Minimum Mark

76

Maintenance Front Brake Lever 1. See page 33 for front brake lever reach adjustments. 2. Lubricate the pivot bushing at the intervals recom-

mended in the periodic maintenance table beginning on page 57. Also lubricate any time binding is evi- dent. Use VICTORY All Purpose Grease or equiva- lent.

3. Inspect brake pads as outlined on page 43.

Front Brake Fluid Change the brake fluid at the intervals recommended in the periodic maintenance table beginning on page 57. Do not attempt to change the anti-lock brake system fluid. See your VICTORY dealer. 1. Straddle the motorcycle and bring it to the fully

upright position. Position the handlebars so that the fluid reservoir is level. Wipe the fluid container and the area around the reservoir cover with a clean cloth.

2. If the fluid level is low, inspect brake pads as out- lined on page 43. If pads are not worn beyond the service limit, inspect the brake system for leaks.

3. To add fluid, remove the three reservoir cover screws. Remove the cover and diaphragm. Carefully add fluid to the top of the sight glass. Do not overfill. Reinstall the diaphragm, cover and screws. Torque: 25 in-lbs (3 Nm)

4. Wipe away any fluid spills. Check for signs of brake fluid leaks around hoses, fittings, reservoir, and brake calipers. Check for deterioration of hoses.

Brake Lever Bushing

Minimum Level

Maximum Level

77

Maintenance Brake Disc Inspection / Cleaning 1. Inspect brake pads as outlined on page 43. 2. Inspect brake discs for nicks, scratches, cracks or

other damage. Inspect the thickness of each brake disc at four or more locations around the disc. If any disc is worn to the minimum thickness at the thinnest point, or if a disc is damaged, see your VICTORY dealer for replacement.

3. Clean discs if minor squeaks develop due to dirt or dust. Apply VICTORY Brake Cleaner (P/N 2872191) to a clean shop towel and wipe disc. DO NOT allow brake cleaner to contact painted or plastic parts. Read all precautions on the label.

Minimum Thickness Front: 4.5 mm Rear: 6.5 mm

78

Maintenance Brake Hoses / Connections Inspect all brake hoses and connections for dampness or stains from leaking or dried fluid. Tighten any leaking connections and replace components as necessary. See the VICTORY Service Manual or your authorized VICTORY dealer.

Wheel Spokes Inspect both wheels for loose, bent, broken or missing spokes (if equipped). To identify loose spokes, grasp each spoke and try to move it side to side or up and down. All spokes should be equally tight and have the same amount of flex. Tighten loose spokes and replace bent, broken or missing spokes (see an autho- rized VICTORY dealer). WARNING! Spokes adjusted or replaced improperly could distort the wheel, make the motorcycle difficult to handle, and cause loss of control.

Wheel Inspection Inspect both wheels for cracks or damage and replace damaged wheels promptly. Do not operate the motorcycle if wheels are damaged or cracked. See the VICTORY Service Manual or your authorized VICTORY dealer.

Anti-Lock Brake System (ABS) Tone Ring/Sensor Inspection 1. Visually inspect for damaged teeth

on the front and rear ABS tone rings. Inspect for nicks and dents on the face of the teeth. The teeth edges should be consistent in appearance. If a tone ring is dam- aged, see your VICTORY dealer for replacement as soon as possi- ble.

2. Inspect for debris adhering to the end of the wheel speed sensors. If contamination is observed, or if you are unable to visually inspect, slide a thin towel across the face of the sensor between the sensor and the tone ring to remove any poten- tial debris. Tone Ring

Teeth Wheel Speed

Sensor

79

Maintenance Tires

Operating the motorcycle with improper tires or with improper or uneven tire pressure could cause loss of control or accident. Always use the correct size and type of tires specified for your vehicle. Always maintain proper tire pressure as recommended in the owner's manual and on safety labels.

Tire Replacement To meet European Union tire directive 97/24 Chapter 1, always replace tires with the tires specified in the table below and in the specifications section of this manual.

Tire Condition Inspect the tire sidewalls, road contact surface, and tread base for cuts, punctures, and crack- ing. Replace damaged tires immediately. See the VICTORY Service Manual or an authorized VICTORY dealer.

Tire Tread Depth Use a depth gauge or an accurate ruler to measure the depth of the center tire tread on both front and rear tires. Replace the tire if the tread depth is less than 1/16 inch (1.6 mm).

WARNING

80

Maintenance Tires Tire Pressure Riding warms the tires and increases tire air pressure. For an accurate reading, check tire pressure before riding. Adjust tire pressure as recommended for the total weight of your intended load (see table). WARNING! Do not exceed the maximum recommended inflation pressure to seat the bead. Tire or rim failure may result.

Spark Plugs Replace spark plugs at the intervals recommended in the periodic maintenance table beginning on page 57. Always replace spark plugs in pairs.

1. Make sure the engine is at room temperature. 2. Pull upward on the spark plug boot (not the wire) to remove the boot. CAUTION! Wear eye and face protection when using pressurized air. 3. To prevent debris from entering the spark plug hole, use compressed air to clean the area

around the plugs before removing them. Remove the spark plugs. Tool: 12 mm plug socket

Tip: Both spark plugs should have the same light or medium tan color deposits. The electrodes should be square with sharp edges.

4. Reinstall the spark plugs or install new plugs. Apply anti-seize compound sparingly to the threads.

Location Size Brand Type Recommended Pressure

Load Weight up to 200 lbs (91 kg)

Load weight up to vehicles maximum

load capacity Front 130/70R18 63H Dunlop Elite 3 36 psi (248 kPa) 38 psi (262 kPa) Front

(Spoke Wheels)

130/70 B18 63H Dunlop 491 Elite ll

32 psi (221 kPa) 36 psi (248 kPa)

Rear 180/60R16 M/C 80H Dunlop Elite 3 38 psi (262 kPa) 40 psi (276 kPa)

Spark Plug Specifications Spark Plug Type NGK DCPR6E

Spark Plug Gap .031-.035 inch (0.8-0.9 mm)

Spark Plug Torque 10.8-14.5 ft-lbs (14.6-19.7 Nm)

031-.035 inch (0.8-0.9 mm)

81

Maintenance Battery The motorcycle battery is a sealed, maintenance-free battery. Do not remove the battery cap strip for any reason. Keep the battery connections clean and tight at all times.

Battery electrolyte is poisonous. It contains sulfuric acid. Serious burns can result from contact with skin, eyes or clothing. Antidote: External: Flush with water. Internal: Drink large quantities of water or milk. Follow with milk of magnesia, beaten egg, or vegetable oil. Call physician immediately. Eyes: Flush with water for 15 minutes and get prompt medical attention. Batteries may produce explosive gases. Keep sparks, flame, cigarettes, etc. away. Ventilate when charging or using in an enclosed space. Always shield eyes when working near batteries KEEP OUT OF REACH OF CHILDREN.

Battery Removal 1. Remove the two upper and two lower

screws from the front chin fairing. Remove the fairing.

WARNING! Improperly connecting or disconnecting battery cables can result in an explosion and cause serious injury or death. When removing the battery, always disconnect the negative (black) cable first. When reinstalling the battery, always connect the negative (black) cable last. 2. Remove the negative (-) battery cable

from the battery terminal. Tool: 10 mm wrench

3. Remove the red protective boot from the positive (+) cable end to expose the terminal. Remove the positive cable from the battery terminal.

4. Remove the battery hold-down strap. 5. Remove the battery.

WARNING

Step 1

Step 1

Step 3 (+)

Step 2 (-)

82

Maintenance Battery Installation WARNING! Improperly connecting or disconnecting battery cables can result in an explosion and cause serious injury or death. When removing the battery, always disconnect the negative (black) cable first. When reinstalling the battery, always connect the negative (black) cable last. 1. Place the battery in the battery compartment

with terminals forward. 2. Reinstall the battery hold-down strap. 3. Install the positive (+) cable first.

Torque: 36 in-lbs (4 Nm) 4. Install the red protective boot over the terminal. 5. Install the negative (-) cable last.

Torque: 36 in-lbs (4 Nm) 6. Reinstall the front chin fairing. Tighten all four

screws. Torque: 36 in-lbs (4 Nm)

Battery Charging Tip: If your VICTORY motorcycle will not be used for a period of 6 weeks or longer, a maintenance

charger should be connected to the battery. A fused maintenance charger connection is provided. The connector is designed for use with the VICTORY accessory maintenance charger available at your authorized VICTORY dealer.

1. Following the charger manufacturers instructions, use a battery charger designed for use with 12-volt batteries. The charger should have a maximum charging rate of 1.8 amps. Charge the battery for approximately 10 hours at a rate of 1.8 amps. If you use a taper or trickle charger, it will take longer to charge the battery.

2. After charging the battery, allow the battery to sit 1-2 hours before checking the state of charge with a DC volt meter. The charge should be a minimum of 12.5 DC volts. Repeat the charging cycle if the charge is less than 12.5 DC volts. Replace the battery if it fails to reach 12.5 volts after the second charge.

Ignition Switch / Lock Lubrication Periodically lubricate the ignition switch, saddle bag locks and fuel cap lock. We recommend the use of VICTORY Multi-Purpose Lubricant. 1. Spray lubricant directly into the ignition switch and into each lock cylinder for 1-2 sec-

onds. 2. Insert each key into its lock and turn it to all positions to distribute the lubricant. 3. Wipe away any excess lubricant.

Sidestand Lubrication Periodically lubricate the sidestand pivot and the ends of the spring. See page 45 for sidestand inspections.

36 in-lbs (4 Nm)

Step 3 (+)

Step 5 (-)

Lubricate

83

Maintenance Handlebar Position On models equipped with two handlebar positions, the motorcycle is manufactured with handlebars in the low position. Before changing handlebar position, check regulations in your area of operation. Operation with the handlebars in the high position may not be legal in all areas or for all riders. WARNING! Handlebar controls must be repositioned each time handlebar position is changed. Failure to reposition handlebar controls could result in loss of vehicle control resulting in severe injury or death. 1. To adjust handlebar position, loosen

the bolts on the bottom of the riser. 2. Adjust the handlebars upward or

downward to the desired position. For high position, align the upper handlebar marks with the split in the riser. For low position, align the lower handlebar marks with the split in the riser.

3. Tighten the front (longer) riser bolts first, then tighten the rear bolts. Torque: 22 ft-lbs (31 Nm)

4. Loosen the screws at the bottom of the left and right handlebar controls and reposition both controls. Make sure the index pin in each control is fully seated in the appropriate handlebar hole before tightening screws. For handlebars in the low position, seat the index pins in the forward set of index holes. For handlebars in the high position, seat the pins in the rear set of holes.

5. Tighten the handlebar control screws. Torque: 25 in-lbs (2.8 Nm)

High Position

Low Position

High Position

Align upper mark to split.

Low Position

Align lower mark to split.

Low Position Use forward holes.

High Position Use rear holes.

Index Pin

84

Maintenance Side Covers Remove the left side cover to access the elec- tronic control module, diagnostic connector and chassis-to-engine harness connector. Remove the right side cover to access the fuses, rear suspension air fitting, clutch cable adjuster, purge valve and flasher unit. Remove both side covers to access the seat screws. 1. Pull outward at each corner of the side cover

to disengage the three darts. 2. Remove the side cover from the motorcycle. 3. To reinstall the side cover, make sure each

rubber grommet is properly positioned. Align each dart with the appropriate grommet and press inward firmly to secure each dart.

Trunk Removal (CROSS COUNTRY TOUR) 1. Open both saddlebag covers. Remove the

left saddlebag and side cover. Place them in a safe location to prevent damage to the painted surfaces.

2. Disconnect the trunk wire harness. 3. Pull the two trunk latch levers fully upward

to release the latches. 4. From the rear of the motorcycle, grasp the

trunk firmly with both hands. Pull the trunk assembly rearward to disengage the trunk support legs from the saddlebag support bracket bushings.

5. Place the trunk assembly in a safe location to prevent damage. 6. Reinstall the side cover and left saddlebag. 7. Reverse this procedure to reinstall the trunk assembly. Make sure the trunk support legs

are firmly anchored onto the saddelbag support bracket bushings. Push both trunk latch levers fully downward to engage the latches. When properly latched, theft prevention bolts prevent latches from rotating and releasing.

WARNING! An insecurely latched trunk assembly can cause loss of control resulting in serious injury or death. Always make sure trunk latches are secure before operating the motorcycle.

Grommets

Latch Release

85

Maintenance Saddlebag Bumpers Saddlebag bumpers (if equipped) can be removed. Be sure to retain the M6 screws, nut plates and spacer plates for future reinstallation. 1. Remove the saddlebags. 2. Remove the five (5) screws securing each bumper to the frame, along with the nut plate

and spacer plate.

3. Remove the bumpers. Place bumpers and hardware in a secure location for future rein- stallation, with the exception of the three (3) M8 screws on each side.

4. Reinstall the M8 screws for mufflers and saddlebag bracket. Torque: 18 ft-lbs (24.4 Nm)

5. Reinstall the saddlebags. 6. To reinstall the saddlebag bumpers, reverse

the removal instructions, using the hardware removed with the bumpers. Tighten the bumper screws to the following specifica- tions: Torque: 84 in-lbs (9.4 Nm) for M6 fasteners Torque: 18 ft-lbs (24.4 Nm) for M8 fasteners

Nut Plate

Spacer Plate

M6 Screws

M8 Screws

M8 Screw

Step 4

86

Maintenance Seat Removal / Installation 1. Remove the side covers. See page 84. 2. Remove the two seat screws.

Tool: 6 mm Allen wrench 3. Lift the front of the seat upward and pull

forward to disengage the tab at the rear of the seat. If equipped, unplug the seat heater.

4. To install, reverse the above process, being sure to engage the tab at the back of the seat.

5. Tighten the seat screws. Torque: 10 ft-lbs (13.5 Nm)

Headlight Aim Inspection The top edge of the high beam must be 3 inches (7.6 cm) below the widest part of the head- light and centered straight ahead at 25 feet (7.6 m).

1. Verify that tire pressure is at specification. See page 80. 2. Verify that rear suspension ride height (preload) is at specification. See page 68. 3. Position the motorcycle on a level surface with the headlight 25 feet (7.6 m) from a wall. 4. With the operator and passenger (if applicable) on board, bring the motorcycle to the

fully upright position. 5. Move the ignition switch to the ON position and switch the headlamp to high beam.

Observe the headlight aim on the wall. 6. Make any necessary adjustments to headlight aim. See page 87.

Seat Screws 10 ft-lbs (13.5 Nm)

25 ft. (7.6 m)

3 in. (7.6 cm)

Height of widest part of headlight

CROSS ROADS (High Beam) 25 ft. (7.6 m)

CROSS COUNTRY (High Beam)

Height of widest part of headlight

3 in. (7.6 cm)

87

Maintenance Headlight Aim Adjustment (CROSS COUNTRY) 1. To adjust the headlamp vertically, remove the

headlight bezel by pulling straight outward at the edges to release the spring clips. Loosen the adjustment screws evenly to adjust the beam downward. Tighten the adjustment screws evenly to adjust the beam upward.

2. To adjust the headlamp horizontally, tighten one screw and loosen the other equally. The beam will adjust to the direction of the tighter screw.

3. Verify proper headlight aim. Readjust if necessary.

Headlight Aim Adjustment (CROSS ROADS) 1. To adjust the headlamp, loosen the adjustment

nut. Adjust the headlamp vertically or hori- zontally.

2. Hold the headlamp firmly in position while tightening the nut. Torque: 28 ft-lbs (38 Nm)

3. Verify proper headlight aim. Readjust if nec- essary.

Headlight Lamp Replacement High Intensity Discharge (HID) Lamps (CROSS COUNTRY) High intensity discharge lamps should be handled only by a trained technician wearing the appropriate protective gear. See the VICTORY Service Manual or an authorized VICTORY dealer.

Halogen Lamps (CROSS ROADS) 1. Unplug the wiring harness from the back of the headlight (lift the tab). Be sure to pull on

the connector, not on the wiring. Tip: Avoid touching a halogen lamp with bare fingers. Oil from your skin leaves a residue, causing a hot

spot that will shorten the life of the lamp. If a lamp is touched, clean it thoroughly with denatured alcohol.

2. Remove the spent lamp and install a new lamp. 3. Reinstall the wiring harness.

Adjustment Screws

Adjustment Nut

88

Maintenance Fuse Replacement NOTICE: Use fuses with the recommended amperage to avoid damage to the electrical system.

Tip: Use the fuse puller provided in the tool kit to remove a fuse.

1. Remove the right side cover. 2. Lift the release tab and slide the fuse

box upward to remove it from the bracket. Release the tabs on each side of the fuse box cover and remove the cover.

3. Remove the damaged fuse and seat the new fuse firmly in its place.

4. Reinstall the fuse box cover with the double cut-out to the left (with print readable from right side of motorcycle).

5. Reinstall the fuse box and the side cover.

Fuse Recommendations Fuse Application Fuse Size Fuse Application Fuse Size

Engine 15 amp Reverse (if equipped) (on rear tire debris flap)

25 amp

Fuel Pump/Ignition Coil 15 amp CROSS COUNTRY ONLY Lights 20 amp Accessory (under right side cover) 20 amp Turn Signals/Horn 10 amp Radio (in fairing behind headlight) 25 amp Ignition 10 amp 12-Volt Storage Compartment Outlet

(TOUR model) (under electrical cover above battery)

10 amp Chassis 20 amp Anti-Lock Brakes (ABS) 30 amp (2)

Fuse Box

Accessory Fuse

(if equipped)

Reverse Fuse (if equipped)

Radio Fuse (if equipped) 12-Volt Storage Compartment

Outlet (if equipped)

ABS Fuses (if equipped)

89

Maintenance Electrical Precautions Be aware of the following precautions regarding the electrical system to avoid disruption of electrical signals and possible system malfunction. DO: DO use ONLY genuine VICTORY parts and accessories designed for your model and fol-

low the instructions provided. DO use the accessory power jack provided (if equipped). If it is necessary to provide power to an item that does not use one of the previously men-

tioned power jacks, connect to the load side of the main circuit breaker (under the cover behind the oil cooler), and connect the ground wire to the engine ground at the front left side of the crankcase (near the circuit breaker).

DO NOT: DO NOT splice or cut any wires. DO NOT tap in to any power or ground on the motorcycle unless specifically directed to

do so by the VICTORY instructions that come with the kit. DO NOT back-probe electrical connectors on the vehicle unless directed to do so by the

Service Manual. DO NOT power any accessories from the diagnostic connector (under left side cover).

Engine Compression Test An engine compression test can be performed to monitor general engine condition. See the VICTORY Service Manual or your authorized VICTORY dealer.

Exhaust System Inspection Check the exhaust system for stains from leaking exhaust gasses. Replace damaged or leak- ing exhaust gaskets. See the VICTORY Service Manual or your authorized VICTORY dealer. Check all exhaust system fasteners. Tighten loose clamps and fasteners. Do not overtighten.

Fastener Torques 1. 12 ft-lbs (16 Nm) 2. 35 ft-lbs (47.5 Nm) 3. 8 ft-lbs (11 Nm) 4. 35 in-lbs (4 Nm) 5. 18 ft-lbs (24 Nm)

2

3

4 3

1

5

5

2

2

90

Maintenance Elevating the Motorcycle WARNING! Serious injury or death can occur if the motorcycle tips or falls. Make sure the motorcycle will not tip or fall while elevated or while on the sidestand. Some procedures require raising the motorcycle to remove weight from the component being inspected. Elevate the motorcycle by placing a stable, flat platform jack or lift mechanism on a firm, flat surface and lifting under the engine crankcase. The platform should be a mini- mum of 12 inches (30 cm) square. DO NOT attempt to lift the motorcycle without proper equipment. Always secure the motorcycle properly before lifting so it cannot tip or fall when elevated.

Road Test Before returning the motorcycle to regular use, perform a road test in a safe area. Pay special attention to the proper fit and operation of all serviced components. Make any corrections or additional adjustments promptly to ensure safe, reliable and enjoy- able vehicle performance.

Fastener Inspection 1. Inspect the entire motorcycle chassis and engine for loose, damaged or missing fasten-

ers. Tighten loose fasteners to the proper torque. Tip: Refer to the specifications section of this manual or the service manual for fastener torque values,

or see your VICTORY dealer. 2. Always replace stripped, damaged or broken fasteners before riding. Use genuine VIC-

TORY fasteners of equal size and strength.

Fastener Torque Refer to the service manual or an authorized VICTORY dealer for procedures and fastener torques not listed in this manual.

Windshield Screws 36 in-lbs (4 Nm) Handlebar End

Cap Screws 84 in-lbs (10 Nm)

Switch Screws 25 in-lbs (3 Nm)

Front Fender 17 ft-lbs (23 Nm)

Front Brake Caliper Mounting Screws 31 ft-lbs (42 Nm)

Rear Axle Nut (Apply grease to threads)

65 ft-lbs (88 Nm)

Front Axle Pinch Bolts

17 ft-lbs (23 Nm) Front Axle 52 ft-lbs (71 Nm)

91

Maintenance Troubleshooting For your personal safety, do not attempt inspection or repairs not fully described in this riders manual. Contact an authorized VICTORY dealer for service if you cannot determine the cause of a problem or if the inspection / repair exceeds your mechanical ability or tool resources. Do not perform any inspection or repair with the engine running.

Engine Cranks But Will Not Start

Starter Motor Does Not Turn or Turns Slowly

Engine Starts But Misses or Runs Poorly Tip: Turn engine OFF before inspecting any of these items.

Possible Cause Possible Remedy/Action Low Fuel Verify fuel level Fuel pump inoperative Turn engine STOP switch to RUN. Turn key ON.

The fuel pump should run momentarily and then stop. If you do not hear the fuel pump run, check the fuel pump / ignition circuit breaker. See page 88. A momentary clicking sound from the IAC valve is normal when the key is first turned to the OFF position.

Battery Discharged Fully charge the battery. See page 82. Spark Plug(s) Fouled Inspect spark plugs. See page 80. Spark Plug Wire(s) Disconnected or Loose Be sure spark plug wires are securely fastened.

Possible Cause Possible Remedy/Action Engine Stop / Run Switch in Stop Position Place switch in RUN position. Battery Discharged Fully charge the battery. See page 82. Battery Cables Loose or Corroded Inspect battery cables. Transmission In Gear Shift transmission into neutral or pull the clutch

lever in to disengage the clutch. See starting pro- cedures on page 48.

Possible Cause Possible Remedy/Action Battery Discharged Fully charge the battery. See page 82. Battery Cables Loose or Corroded Inspect battery cables and connections. Spark Plug(s) Fouled Inspect spark plugs. See page 80. Spark Plug Wire(s) Loose or Wet Inspect spark plug wires, ensure dry/secure. Contaminated Fuel Inspect fuel for water / contamination. See dealer. Engine Oil Level Incorrect Or Wrong Type Inspect level and quality of oil. See page 40. Loose, Broken, Shorted Ignition Coil Wires Inspect coil primary wires. See dealer. Air Intake Restricted Inspect air filter. See page 60.

92

Maintenance Troubleshooting Shifting Difficulties or Hard to Find Neutral

Battery Charging Rate Low or Battery Discharges

Brake Noise / Poor Brake Performance Tip: Contact a VICTORY dealer if brake performance does not return after these inspections.

Anti-Lock Brake Light Remains Illuminated or Illuminates Intermittently

Service Manual Availability Some procedures are beyond the scope of this manual. See your dealer to purchase a VIC- TORY Service Manual for your motorcycle. Some procedures provided in the Service Manual require specialized knowledge, equipment, and training. Be sure you have the required technical skills and tools that are needed before you attempt ANY service on your motorcycle. Please contact your VICTORY dealer before attempting any service work that is beyond your level of technical knowledge or experience, or if the work requires specialized equipment.

Possible Cause Possible Remedy/Action Shift Linkage Bushings Dry Or Worn Lubricate shift linkage. Engine Oil Level Incorrect Or Wrong Type Inspect level and quality of oil. See page 40. Clutch Damage Replace clutch.

Possible Cause Possible Remedy/Action Loose/Corroded Charging Circuit Connection

Check/clean battery cable connections. Check/clean charging circuit connections. See dealer.

Accessory Load Exceeds Charge Rate Limit accessory operation when the engine is off. Improperly Wired Accessory (Current Draw) See dealer to check charging system output and cur-

rent draw. Battery discharges when motorcycle not in use.

See dealer to check key OFF current draw.

Possible Cause Possible Remedy/Action Dust / Dirt On Brake Disc(s) Clean disc. See page 77. Worn Pads Or Disc / Brake Disc Damage Inspect pads. See pages 43 and 77. Brake Fluid Level Low Or Fluid Contaminated Inspect fluid level / fluid. See pages 41 and 42.

Possible Cause Possible Remedy/Action Blown fuse Check the fuses. See page 88. Loose or damaged pulse ring Inspect pulse ring for looseness or chipped teeth. Debris lodged in components Inspect wheel speed sensor and pulse ring for debris. Damage caused by debris Inspect wheel speed sensor for cracked housing. Damaged components See service manual or authorized dealer.

93

Cleaning and Storage VICTORY Cleaning Products This section provides tips on the very best way to clean, polish and preserve every surface of your beautiful new VICTORY Motorcycle. We recommend the use of our new Pure VIC- TORY cleaning and polishing products and accessories, which have been specially designed to offer the best care possible for your VICTORY motorcycle. In addition to the products recommended in this section for cleaning and polishing, Pure VICTORY Polishes also has specialty products for: removing scratches, scuffs and swirls enhancing black and silver engines cleaning engines, tires and wheels removing brake dust After cleaning the motorcycle, inspect for damage to the painted surfaces. Repair chips or scratches promptly by applying VICTORY touch-up paint to prevent corrosion. For more information, or for answers to your cleaning and detailing questions, see your VICTORY dealer or write to the Pure VICTORY Polishes Staff at: victorymailbag@polarisind.com.

Washing the Motorcycle NOTICE: Do not use pressurized water to wash the motorcycle. Water may seep in and deteriorate

wheel bearings, brake caliper assemblies, brake master cylinders, electrical connectors, steering head bearings, and transmission seals. Do not direct any water stream at air intakes, exhaust outlets or electrical connectors. Electrical components may be damaged by water. Do not allow water to contact electrical components or connectors. Do not use glass cleaners, water or soil repellents, and petroleum or alcohol based cleaners on the windshield, as these products can damage the windshield.

1. Before washing, make sure exhaust pipes are cool. Cover each pipe opening with a plas- tic bag secured with a strong rubber band. Check that the spark plugs, spark plug wire caps, oil fill cap and fuel caps are properly seated.

2. Rinse off as much dirt and mud as possible with water running at low pressure. Use as little water as possible when washing near the air cleaner or the exhaust pipe openings. Dry these components thoroughly before using the motorcycle.

3. Clean the front fork tubes thoroughly to reduce fork seal wear and leakage. 4. After washing, remove the rubber bands and plastic bags from the exhaust pipes. Start

the engine and let it idle for a few minutes. Make sure the brakes are functioning prop- erly before riding.

94

Cleaning and Storage Washing the Motorcycle There are two totally different styles of motorcycle washing and there is a Pure VICTORY Polish product for each style.

Standard Bucket Wash This is the conventional way to wash your motorcycle. We recommend the use of Pure VIC- TORY Bike Wash Concentrate, a concentrated gentle product formulated to clean without diminishing the life of any durable polish. This product does not contain alkalis, acids or abrasives and is formulated to perform as a wetting agent to soften bugs, road grime and soil, and to prevent abrasion from your wash mitt or cloth. This product also decreases drying time without spotting or streaking. 1. Add 1 ounce (about 2 capfuls) to 1 gallon of water. 2. Apply to a cool motorcycle with a wool or microfiber wash mitt. Tip: For best results, work one side of the motorcycle at a time, working from top to bottom. 3. Rinse thoroughly with an open hose, no pressure needed. Create a sheeting action to

eliminate spotting. 4. Use a Pure VICTORY Microfiber Chamois or Plush Microfiber Towel to dry virtually

spot-free.

Spray-Rinse-and-Ride Wash This is the new way to clean your VICTORY quickly and easily, then resume riding. Pure VICTORY Spray Rinse and Ride bike wash is safe and will not harm any surface that water wont harm. If you clean your bike frequently, you may mix this product 50/50 with water. Spray the product on surfaces cool to the touch. DO NOT spray on a hot motorcycle. When applied, this product softens dirt, soil, bugs and road grime. 1. Spray windshields, body panels, saddle bags, trunks, engines, tires, wheels, pipes and

chrome. Consistent and complete coverage of the motorcycle is important for best results.

Tip: Use a cloth or wash mitt on stubborn areas. 2. DO NOT allow the product to dry on your motorcycle. Blast rinse with a garden hose

equipped with a pressure nozzle. Be sure to rinse thoroughly, then use a gentle rinse to create sheeting action of the water to lessen the possibility of spotting. Use a Pure VIC- TORY Microfiber Chamois or Plush Microfiber Towel to dry virtually spot-free.

95

Cleaning and Storage Washing the Motorcycle Quick Clean-Ups For quick clean-ups between washings, or when water is not available, use Pure VICTORY Spray & Wipe Instant Detailer, a complete spray-and-wipe product designed to clean and polish all surfaces. It works quickly and easily and is silicone-free so it leaves no oily nor white residue. It provides protection from UV rays, acid rain, and dirt. It will remove bugs, road tar, and road grime from your windshield, paint and chrome. This product is safe for all surfaces, including pin striping, custom paint or murals. Its safe for Plexiglas, Lexan, Acrylic or factory-coated windscreens. Its non-streaking, and it provides polish protection and a water-repellent shine. 1. Spray on all surfaces, including the windshield, paint, chrome, wheels and leather to

clean, polish and protect. 2. Wipe dry with Pure VICTORY Plush Microfiber Towel. DO NOT use a T-shirt. 3. Spray on and wipe off to easily remove bugs, dust and water spots. For heavily soiled

surfaces, use product more liberally. Tip: Use this product on the windshield to repel water and enhance rain visibility.

Polishing the Motorcycle Polished Aluminum Care When a VICTORY is new, the polished aluminum wheels, hand levers and shifter shine like chrome. Ultraviolet (UV) rays and oxidation will cause polished aluminum to grow dull, however, if its not properly polished and protected. Pure VICTORY Awesome Metal Polish will clean, polish and protect these aluminum sur- faces. This metal polish will restore that factory chrome-like shine and leave a protective coating that resists future oxidation for several months. Pure VICTORY Awesome Metal Polish provides instant results you must see to believe! 1. Shake the polish container well before using. 2. Apply the product with a terry cotton or microfiber cloth or pad. 3. Rub gently until the black begins to come to the surface or until shine begins to show

through the haze. 4. Allow the product to haze. 5. Remove the haze with a terry cotton or microfiber cloth and buff to a long-lasting

chrome-like shine. 6. Do not polish the spokes on painted laced wheels.

96

Cleaning and Storage Polishing the Motorcycle There are now two totally different styles of polishing or protecting your paint and chrome.

Standard Method of Polishing Paint and Chrome Pure VICTORY Windshield, Paint and Chrome Polish is a unique formula designed to pro- duce a glass-like shine on painted or clear-coated finishes and chrome surfaces. Use it on chrome-plated accessories to prevent surface rust and create a glass-like shine. This product creates a high reflective index point, giving a deep, shiny finish without sili-

cone. Use it to polish and fill light scratches on Plexiglas, Lexan, Acrylic and factory-coated

windshields. It repels water from windshields and keeps bugs from sticking. Windshield, Paint and Chrome Polish provides long-lasting protection from oxidation,

corrosion, UV rays and heat.

Standard Method of Polishing Paint and Chrome 1. Shake the container well before using. 2. Apply with Pure VICTORY 100% Microfiber Wax Applicator in a circular motion or

straight line to a clean surface. It can be applied in direct sunlight. 3. Rub the product until it is almost clear, then allow to dry to a haze before removal. The

entire motorcycle can be treated before removing polish. 4. Use a Pure VICTORY Polishes Plush Microfiber Towel to wipe it off easily and dust-

free. 5. For best results on a windshield, apply to a clean windshield. Once applied, rain water

beads and blows off, enhancing rain visibility. The glass-like finish keeps bugs from sticking and permits their easy removal.

97

Cleaning and Storage Polishing the Motorcycle Premium Polishing for Long-Lasting Protection This newer style of polishing paint and chrome utilizes the latest in high-quality polymer technology that provides the longest-lasting protection available in the polish industry today. Pure VICTORY Liquid Spray Wax for Windshields, Paint & Chrome is formulated for pol- ishing after washing and can be sprayed on wet or dry surfaces. Liquid Spray Wax quickly produces a durable, high-gloss shine with minimal effort. It contains NO ABRASIVES and is clear coat-safe. It contains NO PETROLIUM DISTILLATES or SILICONES. 1. Shake container well before use. 2. Begin by washing and rinsing the motorcycle. 3. Spray Liquid Spray Wax on a wet or dry bike, one section at a time. (For best results, the

bikes surface should be cool.) 4. Wipe dry one section at a time with Pure VICTORY Microfiber Chamois or microfiber

towel. 5. When finished drying, buff the entire motorcycle with a clean, dry Pure VICTORY

Microfiber Polishing Towel for a clean and luxurious shine. Tip: Liquid Spray Wax can also be applied to clean and dry clear coats, windshields and chrome. Apply

to one section at a time and wipe dry. When finished, use a second towel to buff to a luxurious, long-lasting shine.

Leather, Rubber and Vinyl Care

Never use a non-recommended protectant on seats, footrests, hand grips or tires. Slippery seats, footrests or hand grips can cause loss of control. Slippery tires can cause loss of traction and loss of control. Both situations could result in serious injury or death.

For the finest leather care, use Pure VICTORY Leather, Vinyl & Rubber Conditioner, a unique, pleasantly scented formula of premium-quality polymers designed to restore luster and softness to vinyl, leather and rubber without making them slippery. This product is a true conditioner, not a coating. It does not close the pores of the surfaces but penetrates, nourishes and softens the material. It protects against ultra violet (UV) rays and cracking, repels water and prolongs the life and like-new appearance of the materials. Applied to rubber, this product creates a water-repellent, like-new appearance. This product can also be used to restore or maintain the factory finish on a VICTORY instrument panel/ dash and rear storage compartment black vinyl surfaces. Regular use increases soil resis- tance. 1. Apply the product on a clean dry surface using a soft cloth. 2. Rub the product into the material. Repeat the treatment if the surface is extremely dry. 3. Wipe dry with a second cloth to remove excess product. Buff lightly with the second

towel for additional luster.

WARNING

98

Cleaning and Storage If you will not operate the motorcycle for several months, such as during the winter, store the motorcycle to prevent damage to the fuel system and the battery and to protect components from corrosion or deterioration. During storage you might use products that are potentially hazardous; such as fuel stabilizer. When using any of these products, follow the instructions and warnings on the product packaging. This section includes instructions for preparing the motorcycle for storage, maintaining it during storage and removing it from storage.

Storage Area Preparation Choose a dry, well-ventilated storage location, inside a garage or other structure if possible. The location should have a firm, flat surface and allow enough space for the motorcycle. To best preserve tire condition: The storage area should have a relatively constant and moderate temperature. The storage surface should be free of oil and gasoline. The motorcycle should not be near a radiator or other heat source, or any type of electric

motor.

Clean and Protect the Motorcycle To prepare the motorcycle for storage, begin by cleaning it as outlined beginning on page 93. Wax painted surfaces and polish chromed and other metal surfaces. Apply protectant to exposed rubber, vinyl, and plastic parts. Do not apply rubber protectant to the tire tread surfaces.

Fuel Stabilizer Using a mixture of fuel and the recommended amount of VICTORY Premium Carbon Clean Plus or other gasoline stabilizer, fill the fuel tank only to the top of the filler insert. Ride the motorcycle or start and run the engine for 15 minutes in a well ventilated area to pass the stabilized fuel through entire fuel-injection system.

Tire Inflation Inflate the tires to normal pressure. See page 80.

99

Cleaning and Storage Engine Protection Change the engine oil. See page 59. Carbon deposits and combustion acids, normally sus- pended in the engine oil when in service, settle on internal engine components during stor- age. Settled deposits can cause engine damage or internal corrosion.

Battery Care 1. Remove the battery. See page 81. 2. Clean the battery terminals first with a wire brush to remove any loose deposits. 3. Wash the posts and the ends of the battery cables with a solution of 1 part baking soda to

16 parts water. Rinse with clean water and wipe dry. 4. Apply a thin film of dielectric grease (available from your VICTORY dealer) to the posts

and cable connectors. 5. Clean the outside of the battery with a solution of mild detergent and warm water. 6. Store the battery in a dry area with a temperature of 32 to 90 F (0 to 32 C). 7. While in storage, fully charge the battery once a month. See page 82.

Park and Cover the Motorcycle Park the motorcycle in its storage location. Cover it with a genuine VICTORY motorcycle cover, or a cover made from a durable, breathable material designed for storage. Covering the motorcycle helps protect it from dust and other airborne materials. The cover must be of a breathable material to prevent moisture from building up on the motorcycle which can cause oxidation of metal surfaces.

Rodents Mice and other rodents are often the worst enemy of a stored motorcycle. If the motorcycle will be stored in an area where mice are a concern (particularly in rural areas, barns, sheds, etc.) be sure to take extra measures to deter their infestation. This may include placing a screen mesh over any intake or exhaust openings (just be sure to remember to remove them when you take the motorcycle from storage).

Maintenance During Storage During extended storage periods, maintain tire pressure and battery voltage at the recom- mended levels.

100

Cleaning and Storage Removal From Storage 1. Remove the cover and unlock the front forks (if locked). 2. Verify that tire pressure is at specification. 3. Install the battery and perform an electrical inspection. 4. Check the oil level. If the motorcycle was stored in an area subject to wide swings in

temperature and humidity (such as outdoors), change the engine oil before starting the engine.

NOTICE: During storage, temperature and humidity changes can cause condensation to form in the crankcase and mix with engine oil. Running the engine with oil that contains condensation can cause engine damage.

5. Inspect the storage area for signs of fluid leaks. Identify and perform service to any leak- ing components.

6. Install new spark plugs if necessary. 7. Wash and polish the motorcycle. Wax, polish, or apply protectant to appropriate compo-

nents. 8. Perform the pre-ride inspections. See page 38. 9. Perform a road test. See page 90.

101

Warranty VICTORY Motorcycle Warranty Policy Limited Warranty VICTORY Motorcycle Division, Polaris Sales Inc., P.O. Box 47700, Hamel, Minnesota 55340-9960, gives a ONE YEAR LIM- ITED WARRANTY on all components of the VICTORY Motorcycle against defects in material or workmanship. This war- ranty covers the parts and labor charges for repair or replacement of defective parts which are covered by this warranty. This warranty begins on the date of purchase. This warranty is transferable to another consumer during the warranty period through a VICTORY Motorcycle dealer. Registration At the time of sale, the Warranty Registration Form must be completed by your dealer and submitted to VICTORY Motorcycle Division, Polaris Sales Inc. within ten days. Upon receipt of this registration, VICTORY Motorcycle Division, Polaris Sales Inc. will record the registration for warranty. No verification of registration will be sent to the purchaser as the copy of the War- ranty Registration Form will be the warranty entitlement. If you have not signed the original registration and received the cus- tomer copy, please contact your dealer immediately. NO WARRANTY COVERAGE WILL BE ALLOWED UNLESS YOUR VICTORY MOTORCYCLE IS REGISTERED WITH VICTORY MOTORCYCLES DIVISION OF POLARIS SALES INC. Initial dealer preparation and set-up of your VICTORY Motorcycle is very important in ensuring trouble-free operation. Pur- chasing a motorcycle in the crate or without proper dealer set-up will void your warranty coverage.

Warranty Coverage and Exclusions: Limitations of Warranties and Remedies The warranty excludes any failures that are not caused by a defect in material or workmanship. This warranty does not cover accidental damage, normal wear and tear, abuse or improper handling. This warranty also does not cover any VICTORY Motor- cycle that has been altered structurally, modified, neglected, improperly maintained, used for racing, or used for purposes other than for which it was manufactured, or for any damages which occur during trailer transit or as a result of unauthorized service or the use of unauthorized parts. In addition, this warranty does not cover physical damage to paint or finish, stress cracks, tear- ing or puncturing of upholstery material, corrosion, or defects in parts, components or VICTORY Motorcycle due to fire, explo- sions or any other cause beyond VICTORY Motorcycle Division, Polaris Sales Inc. control. This warranty does not cover the use of unauthorized lubricants, chemicals, or fuels that are not compatible with the VICTORY Motorcycle. The exclusive remedy for breach of this warranty shall be, at VICTORY Motorcycle Division, Polaris Sales Inc. exclusive option, repair or replacement of any defective materials, or components or products. THE REMEDIES SET FORTH IN THIS WARRANTY ARE THE ONLY REMEDIES AVAILABLE TO ANY PERSON FOR BREACH OF THIS WARRANTY. VIC- TORY MOTORCYCLES DIVISION OF POLARIS SALES INC. SHALL HAVE NO LIABILITY TO ANY PERSON FOR INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES OF ANY DESCRIPTION, WHETHER ARISING OUT OF EXPRESS OR IMPLIED WARRANTY OR ANY OTHER CONTRACT, NEGLIGENCE, OR OTHER TORT OR OTHER- WISE. THIS EXCLUSION OF CONSEQUENTIAL, INCIDENTAL, AND SPECIAL DAMAGES IS INDEPENDENT FROM AND SHALL SURVIVE ANY FINDING THAT THE EXCLUSIVE REMEDY FAILED OF ITS ESSENTIAL PUR- POSE. Some states do not permit the exclusion or limitation of incidental or consequential damages or implied warranties, so the above limitations or exclusions may not apply to you if inconsistent with controlling state law.

102

Warranty VICTORY Motorcycle Warranty Policy Limitations of Warranties and Remedies ALL IMPLIED WARRANTIES (INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANT- ABILITY AND FITNESS FOR A PARTICULAR PURPOSE) ARE LIMITED IN DURATION TO THE ABOVE ONE YEAR WARRANTY PERIOD. VICTORY MOTORCYCLES DIVISION OF POLARIS SALES INC. FURTHER DISCLAIMS ALL EXPRESS WARRANTIES NOT STATED IN THIS WARRANTY OTHER THAN EMISSIONS AND EXCISE WARRAN- TIES. Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you if inconsistent with controlling state law.

How To Obtain Warranty Service If your VICTORY Motorcycle requires warranty service, you must take it to a VICTORY Motorcycle Servicing Dealer. When requesting warranty service you must present your copy of the Warranty Registration form to the dealer. (THE COST OF TRANSPORTATION TO AND FROM THE DEALER IS YOUR RESPONSIBILITY). VICTORY MOTORCYCLES division of Polaris Sales Inc. suggests that you use your original selling dealer; however, you may use any VICTORY Motorcycle Ser- vicing Dealer to perform warranty service. Please work with your dealer to resolve any warranty issues. Should your dealer require any additional assistance they will con- tact the appropriate person at VICTORY MOTORCYCLES division of Polaris Sales Inc. This warranty also gives you specific legal rights, and you may also have other rights which vary from state to state. If any of the above terms are void because of state or federal law, all other warranty terms will remain in effect.

103

Specifications CROSS ROADS CROSS COUNTRY

Dimensions (Dimensions and specifications may vary with features, options and accessories) Overall Length 104.4 in. (265 cm) 104.4 in. (265 cm)

108.2 in. (274.8 cm) w/Trunk Overall Width 36 in. (91.4 cm) 39.2 in. (99.5 cm) Overall Height 56.3 in. (143 cm) 53.2 in. (135.1 cm) Seat Height 26.3 in. (66.8 cm) 26.3 in. (66.8 cm) Wheel Base 65.7 in. (167 cm) 65.7 in. (167 cm) Ground Clearance 5.8 in. (14.8 cm) 5.8 in. (14.8 cm) Rake & Trail 29/5.6 in. (14.2 cm) 29/5.6 in. (14.2 cm) Weight Dry Weight 758 lbs. (345 kg) (HARD-BALL)

770 lbs. (349 kg) (Classic) 765 lbs. (348 kg)

800 lbs. (364 kg) w/Trunk 845 lbs. (384 kg) Tour

Wet Weight 793 lbs. (360 kg) (HARD-BALL) 805 lbs. (365 kg) (Classic)

800 lbs. (364 kg) 835 lbs. (380 kg) w/Trunk

880 lbs. (400 kg) Tour Maximum Load Capacity (riders, cargo, accessories, options)

580 lbs. (263 kg) 560 lbs. (255 kg) 525 lbs. (239 kg) w/Trunk

480 lbs. (218 kg) Tour Gross Vehicle Weight Rating (GVWR) (see page 14)

1360 lbs. (617 kg)

Gross Axle Weight Rating (GAWR) Front Axle: 460 lbs. (209 kg) Rear Axle: 900 lbs. (408 kg)

CROSS ROADS / CROSS COUNTRY Capacities Engine Oil 5 qt. (4.75 l)

Approximately 4.5 qt. (4.25 l) at oil change Fuel 5.8 gal. (22 l) Fuel Reserve 1.2 gal. (4.5 l) Engine Engine Type VICTORY Freedom 106 / 6 V-Twin Configuration 50 V-Twin 4 Stroke SOHC Displacement 106 Cubic Inch (1731 cc) Cooling System Air & Oil Compression Ratio 9.4:1 Valve Train 4 Valves per cylinder, Hydraulic Lifters & Self-Adjusting Cam Chains Bore & Stroke 101 x 108 mm Throttle Body Bore 45 mm Electronic Fuel Injection System Closed Loop Lubrication System Wet Sump Spark Plug / Gap NGK DCPR6E / .031-.035 inch (0.8-0.9 mm) Exhaust Split dual exhaust with crossover

104

Specifications CROSS ROADS / CROSS COUNTRY

Chassis Front Suspension Type / Travel Telescopic Fork / 5.1 in. (13 cm) Front Fork Tube Diameter 43 mm Rear Suspension Type / Travel Single Monotube Air Adjustable Shock: 4.7 in. (12 cm) Swingarm Cast Aluminum with Constant Rate Linkage Front Brakes Dual 300 x 5 mm / Floating Rotor / 4 Piston Calipers Rear Brakes Single 300 x 7 mm / Floating Rotor / 2 Piston Caliper Total Storage Volume 21.3 gallons (80.6 liters) Drive System Final Drive Type Carbon Fiber Reinforced Belt Transmission Type 6 Speed Constant Mesh with True Overdrive Primary Drive Type (Reduction Ratio) Gear Drive with Torque Compensator (1.49:1)

Drive System Gear Shift Pattern 1 Down 5 Up Internal Gear Ratios

1st 3.13:1 2nd 2.02:1 3rd 1.50:1 4th 1.20:1 5th 1:1 6th (Overdrive) .87:1

Final Drive Ratio 2.12:1 Clutch Type Wet, Multi Plate, Diaphragm Spring Wheels And Tires Front Wheel Type / Size Cast or Billet 18 x 3.0 inch

Laced 18 x 3.5 (Classic/HARD-BALL) Front Tire Type / Size DUNLOP Elite 3 - 130/70R18 63H Radial

Dunlop 491 Elite ll - 130/70 B18 63H (Classic/HARD-BALL) Rear Wheel Type / Size Cast or Billet 16 x 5.0 inch

Laced 16 x 5.0 (Classic/HARD-BALL) Rear Tire Type / Size DUNLOP Elite 3 - 180/60R16 M/C 80H Radial Electrical Alternator 48 Amp Maximum Output Battery 12 Volt / 18 Amp Hour / 310 CCA / Yuasa YTX20HL Lights Headlamp (High / Low) High H11 / Low H11 HID Headlamp (High / Low) High H11 / Low D1SR Auxiliary Forward Lamps (if equipped) H3 25w Turn Signal Lamp Non-Serviceable LED Tail / Brake / License Plate Lamp Non-Serviceable LED Fuses / Circuit Breakers Engine 15A Fuel Pump/Ignition Coil 15A Lights 20A Turn Signals/Horn 10A Ignition 10A Chassis 20A Anti-Lock Brake System 30A (2) Reverse 25A Accessory 20A (CROSS COUNTRY) Radio 25A (CROSS COUNTRY) 12-Volt Outlet (Storage Compartment) 10A (CROSS COUNTRY TOUR)

105

Specifications Fuel Recommendation For best performance, use only unleaded gasoline with a 91 pump octane minimum (R+M/2 Method). DO NOT USE E-85 GASOLINE OR GASOLINE CONTAINING METHANOL. Using E85 or gasoline / methanol blends can result in poor starting and driveability, and may damage critical fuel system components. Gasoline containing up to 10% Ethanol can be used. Gasoline containing up to 15% Methyl Tertiary Butyl Ether (MTBE) can be used.

Engine Oil Recommendation Polaris Recommends the use of VICTORY brand Semi-Synthetic 20W-40 Motor Oil or equivalent motorcycle oil that is approved for use in wet clutch transmissions (such as those with a JASO MA rating).

Identification Number Record Record important identification numbers below.

Vehicle Identification Number (VIN) (see page 15)

Engine Identification Number (see page 16)

Ignition Key Number (see page 16)

106

Audio System Overview Audio System Introduction Not all motorcycles are equipped an audio system. Motorcycles equipped with an audio system may not be equipped with all components discussed in the audio section of this manual. Components not installed at the factory can be purchased from and installed by your VICTORY dealer. Software Updates Radio system software should be updated annually to ensure the best performance. Please see your authorized VICTORY dealer for this service.

Radio Frequencies North America AM 520 to 1720 kHz FM 87.9 to 107.9 MHz WX 162.40 to 162.55 MHz European FM 87.5 to 108.00 MHz MW 522 to 1602 kHz LW 144 to 288 kHz

Audio Controls Operation of the audio controls is outlined in greater detail on the following pages.

U.S.A. Sources

European Sources

Mode Menu Options

Audio Controls

1. Mode Button: Press and hold the MODE button until the system enters the audio system mode menus. Then press and release the MODE button until the desired mode menu displays.

Tip: Some mode menu options have sub-menus. Sources and menu options will be displayed only for installed components.

2. Tuner Button: Press and release TUNE (+) or TUNE (-) to change radio stations or iPod tracks. Press and hold to auto- matically seek or scan.

3. Volume Button: Press VOL (+) to turn the audio system on. Press VOL (+) to increase audio volume. Press VOL (-) to decrease audio volume. Press and hold to rapidly increase or decrease volume. When volume is decreased until OFF displays, continuing to press and hold VOL (-) for two seconds will turn the radio off.

4. Memory Preset (PRE) Button: Press PRE to cycle through the stored preset locations. See page 110.

FM AM WX AUX (NAV MP3, AUX or iPod) XM Radio

FM MW LW AUX (NAV MP3, AUX or iPod)

Bass CB Local/Distant Treble AM/FM Clear Preset Fader Radio Data System External Speakers AUX Mode Automatic Volume Control XM Clear Preset CB Headset ENT Mode XM Display ICOM Volume XM Category CB Volume

3 12

4

107

Audio System Overview Citizens Band (CB) Radio Controls If equipped, the operators CB radio controls are located on the left handlebar above the audio controls. Operation of these controls is outlined in greater detail on the following pages. 1. Push-to-Talk (PTT): Press and hold the top or bottom of

the button to transmit. See page 116. 2. Squelch: Press SQ (+) or SQ (-) to adjust CB radio chan-

nel reception sensitivity. See page 116. 3. COM: Press COM to turn the CB radio on or off. Press

and hold COM to select a COM channel. 4. ICOM: Press ICOM to turn the driver/passenger intercom

on or off. Press and hold ICOM to access Voice-Activated Switch (VOX) settings. See page 118.

Passenger CB Controls The passengers radio controls are located on the headset cord. 1. Push-to-Talk (PTT): Press and hold the button to trans-

mit. 2. Rear Volume: Press (+) or (-) to adjust the rear headset

volume.

1 32

4

1 2

108

Audio System Operation Audio System Power The ignition key must be in the ACC or ON position to use the audio system. With the key in the ACC or ON position and audio system OFF, the screen will display VICTORY. Tip: To prevent battery drain, do not leave the key in the ACC position for long periods. VICTORY rec-

ommends using the audio system only when the engine is running. Press VOL (+) to turn the audio system on. The screen will display the active entertainment source. 1. Current audio source:

(U.S.) FM / AM / WX / iPod - AUX / XM (Euro) FM / MW / LW / iPod - AUX

2. Station preset number (P1-P15) 3. Stereo indicator 4. Intercom system active (if equipped) 5. CB radio active channel (if equipped) Tip: The audio system will always display the last active source when turned on.

Audio Volume Control The driver can adjust volume for the speakers and turn the speakers off or on. Audio Volume Press and release VOL (+) or VOL (-) to raise or lower volume.

VICTORY

FM ICOM CB19

P1 ST

97.1 1

2

5

3

4

109

Audio System Operation Selecting Audio Sources Press and release the MODE button until the desired source is active.

FM source active: U.S. / European models

AM source active: U.S. models only

WX (Weather) source active: U.S. models only

NAV MP3 source active: U.S. / European models

iPod source active: U.S. / European models (skipped if not equipped)

AUX source active: U.S. / European models

XM Radio source active: U.S. models only (skipped if not equipped)

MW (Medium Wave) Source: European models only

LW (Long Wave) source: European models only

FM ST

97.1

AM

1130

WX

3

AUX

NAV MP3

Artist Title

Playlist

iPod

AUX

AUX

CH25 P6 Sting

Fields of Gold

TheBlendXM

531 MW

144 LW

110

Audio System Operation Audio Tuning Use the tuner on the left control to select radio stations. Press and release TUNE (+) or TUNE (-) to locate stations in single-step increments. Press and hold TUNE (+) or TUNE (-) to seek or scan for stations depending on mode setting.

Memory Presets The audio system features 15 user-defined presets for storing favorite stations. 1. To set a preset,

press and release the MODE button until the desired source is active (FM, AM, WX, XM, MW, LW).

2. Use TUNE or seek/scan to locate a radio station.

3. Press and hold the PRE button.

4. Press TUNE (+) or TUNE (-) to cycle to an available preset location. The preset location displays on the screen.

5. When the desired location is displayed, press and hold the PRE button to store the selected radio station.

Tip: If the desired preset location already con- tains a stored radio station, it will be over- written by the new selection.

6. Wait 5 seconds or push VOL (+) or VOL (-) to exit.

7. To listen to a preset location, press and release the PRE button until the desired location displays.

100.5+ TUNE

- P1 ---.-

Station being stored

100.5+ TUNE

- P1 97.1 Station will be overwritten

111

Audio System Operation Audio Mode Menus Entering Mode Menus Press and hold the MODE button until the system enters the audio system mode menus. Then press and release the MODE button until the desired mode menu displays. To change mode settings, enter the mode menu. Press TUNE (+) or TUNE (-) to change settings. Wait 5 seconds or push VOL (+) or VOL (-) to exit.

Exiting Mode Menus Exit the screen and return to the default dis- play in one of two ways. 1. Wait 5 seconds.The system will auto-

matically exit. 2. Press VOL (+) or VOL (-). Tip: The volume will also change.

Bass Setting Press TUNE (+) or TUNE (-) to adjust.

Treble Setting Press TUNE (+) or TUNE (-) to adjust.

Fader Setting Press TUNE (+) or TUNE (-) to adjust.

External Speakers Press TUNE (+) or TUNE (-) to turn the speakers on or off.

+ TUNE

-

+ TUNE

-

+ TUNE

-

BASS 0

BASS +3

BASS -3

+ TUNE

-

+ TUNE

-

+ TUNE

-

TREBLE 0

TREBLE +3

TREBLE -3

+ TUNE

-

FADERR F

+ TUNE

-

EXTERNAL SPKRS OFF

EXTERNAL SPKRS ON

+ TUNE

-

112

Audio System Operation Audio Mode Menus To change mode settings, enter the mode menu. Press TUNE (+) or TUNE (-) to change settings. Wait 5 sec- onds or push VOL (+) or VOL (-) to exit.

Automatic Volume Control (AVC) When set, this feature will lower or raise the speaker/ headset volume automatically, based on vehicle speed. Press TUNE (+) or TUNE (-) to change settings. Off: Volume will not adjust Low: Least aggressive setting Medium: Moderate setting High: Most aggressive setting

CB Headset Volume Controls (if equipped) The headsets have three separate volume settings: Intercom (ICOM) volume, CB receive volume and entertainment (ENT) volume. Always position headsets with the speakers directly over your ears to ensure the best sound quality and volume. Tip: The driver can turn off the external speakers and listen to audio only through the headsets. See

page 111.

CB Headset ENT Mode (if equipped) OFF: Only communications are audible in the headsets. Riders can listen to navigation commands and entertainment with the external speakers while reserving the headset for communication. MIX: The audio source volume drops lower than the ICOM volume whenever the voice-operated switch (VOX) is opened. The audio source volume gradually returns to its original level after the VOX is closed. MUTE: The audio source volume is muted when the VOX is opened. The audio source volume gradually returns to its original level after the VOX is closed.

Volume Adjustments Item Can Be Adjusted Driver Controls Passenger Controls

ICOM Volume When VOX is in use Press VOL (+) or VOL (-) Press (+) or (-) on the

headset cord controlCB Receive Volume When receiving a CB transmission ENT Volume While listening to ENT

+ TUNE

-

+ TUNE

-

AUTO VOL CONTROL OFF

AUTO VOL CONTROL LOW

AUTO VOL CONTROL MEDIUM

AUTO VOL CONTROL HIGH

+ TUNE

-

+ TUNE

-

HEADSET ENT MODE OFF

HEADSET ENT MODE MIX

+ TUNE

-

+ TUNE

-

HEADSET ENT MODE MUTE

+ TUNE

-

113

Audio System Operation Audio Mode Menus To change mode settings, enter the mode menu. Press TUNE (+) or TUNE (-) to change settings. Tip: Sources and menu options will be displayed

only for installed components.

Driver ICOM Volume Press TUNE (+) or TUNE (-) to adjust.

Driver CB Volume Press TUNE (+) or TUNE (-) to adjust.

CB LO/DX Mode Press TUNE (+) or TUNE (-) to change set- tings. See page 117 for more detailed infor- mation.

Radio Data System (RDS) Press TUNE (+) or TUNE (-) to turn the radio data system on or off. When on, the screen will display artist, song title, etc. (if available in the radio signal).

AUX Mode Press TUNE (+) or TUNE (-) to choose AUX (for iPod or any other MP3 player use) or NAV MP3 (for navigation unit MP3 player use). Tip: NAV MP3 mode will override any device

connected with an input cable. If using NAV MP3 mode, always pause the GARMIN unit before changing sources. Otherwise, music from the NAV unit will interrupt the new source, interpreting it as navigation com- mands, not music.

+ TUNE

-

ICOM VOL 15

+ TUNE

-

CB VOL 15

+ TUNE

- CB LO / DX MODE

DISTANT

+ TUNE

- CB LO / DX MODE

LOCAL

RDS OFF

RDS ON

+ TUNE

-

+ TUNE

-

AUX MODE AUX

AUX MODE NAV MP3

+ TUNE

-

+ TUNE

-

114

Audio System Operation Audio Mode Menus To change mode settings, enter the mode menu. Press TUNE (+) or TUNE (-) to change settings. Tip: Sources and menu options will be displayed

only for installed components.

XM Display Press TUNE (+) or TUNE (-) to set the screen to display channel name or category when the XM radio is active.

XM Category Press TUNE (+) or TUNE (-) to set the music selection category when tuning XM. These categories are downloaded from XM whenever the XM antenna is receiving a signal and may change from time to time. Tip: Selecting a category will then limit the chan-

nels available to those within that category until ALL CHANNELS or another category is selected.

Weather Band (WX) Weather band channels are broadcast by the National Oceanic and Atmospheric Admin- istration (NOAA). NOAA operates more than 940 transmitters covering the United States, Puerto Rico, the U.S. Virgin Islands, the U.S. Pacific Territories and adjacent coastal waterways. Press and release the MODE button until the desired source is active. When the WX source is selected, a total of 7 weather band channels are available. Typically, only one weather band channel will be available for a given location. When traveling, if a channel becomes unavailable, search for another active channel. Press TUNE (+) or TUNE (-) to access a channel.

WX Channels

XM DISPLAY CHANNEL NAME

XM DISPLAY CATEGORY

+ TUNE

-

+ TUNE

-

XM CATEGORY All Channels

XM CATEGORY MorMusic

XM CATEGORY Traffic

+ TUNE

-

+ TUNE

-

+ TUNE

-

WX Ch. Freq. 1 162.400 2 162.425 3 162.450 4 162.475 5 162.500 6 162.525 7 162.550

115

CB Radio / ICOM System CB/ICOM Introduction In the U.S.A., refer to the Federal Commu- nications Commission (FCC) Plain Rules pamphlet accompanying this riders manual for a comprehensive guide of citizens band (CB) radio rules and regulations. Headset Use The use of helmet-mounted headsets may be restricted or prohibited in some areas. Always obey all applicable regulations and laws. The headsets have three separate volume settings: Intercom (ICOM) volume, CB receive volume and entertainment (ENT) volume. See page 112.

Getting Started Tip: To minimize distractions while riding, always

make adjustments to the CB/ICOM system prior to operating your motorcycle.

Tip: To prevent battery drain, do not leave the key in the ACC position for long periods. VICTORY recommends using the audio sys- tem only when the engine is running.

The ignition key must be in the ACC or ON position to use the audio system. 1. Press VOL (+) to turn the audio system

on. 2. Press COM on

the left control to activate the CB/ COM system.

CB Channels When the CB radio system is active, CB and the active channel will display.

Press and hold COM on the upper left control to access the CHANNEL ADJUST screen. Push COM or ICOM to change channels.

Tip: Changing to a new channel may require changing the squelch setting.

Wait 5 seconds or push VOL (+) or VOL (-) to exit the screen and return to the main dis- play.

FM ICOM CB19

P1 ST

100.5

COM +/-

ICOM CB 19 CHANNEL ADJUST

116

CB Radio / ICOM System Push-to-Talk (PTT) Press and hold the top or bottom of the PTT button to transmit over CB radio. The passen- ger must push and hold the PTT button on the headset con- trols. Tip: PTT will activate the intercom when the

intercom is turned on and the CB is turned off.

TX will display on the console screen when one of the PTT buttons is pressed. RX will display when the CB is receiving a transmission.

Squelch Squelch blocks unde- sired signals and noise by allowing the reception of signals only over a specified level. Press and release the SQ (+) or SQ (-) but- tons to adjust the squelch to any level between OPEN and CLOSED.

When squelch is set to OPEN, no filtering occurs. Setting squelch to CLOSED blocks all signals, including strong signals. To set the squelch level, first lower the squelch level until noise or static is audible. Gradually increase the squelch level until the noise or static is gone.

Driver CB Radio Volume To change settings, enter the mode menu. Press TUNE (+) or TUNE (-) to adjust settings.

Tip: The CB volume can also be set using the hand control when the CB is receiving.

Passenger CB Radio Volume The passenger can control rear headset volume when Entertainment, CB radio or ICOM is active. Press (+) or (-) on the headset control to raise or lower vol- ume.

Transmitting

Receiving

FM ICOM TX19 100.5

FM ICOM RX19 100.5

+ SQ

-

SQUELCH 8

+ TUNE

-

CB VOL 15

117

CB Radio / ICOM System Local/Distant CB Radio Mode To change mode settings, enter the mode menu. Press TUNE (+) or TUNE (-) to set the CB to local (LO) or distant (DX) mode. Distant: Use this setting for weaker signals. Receiver sensitivity will be increased. Static and noise levels are increased. Local: Use this setting for stronger signals or in high density areas. Receiver sensitivity will be decreased. Static and noise levels are decreased.

CB Radio Frequencies The FCC has designated 40 citizen band (CB) channels for consumer use. Channel 9 is des- ignated as an EMERGENCY channel for emergency use only. CB Channels / Frequencies

Ch. Freq. Ch. Freq. Ch. Freq. Ch. Freq. Ch. Freq. Ch. Freq.

1 26.965 8 27.055 15 27.135 22 27.225 29 27.295 36 27.365

2 26.975 9 27.065 16 27.155 23 27.255 30 27.305 37 27.375

3 26.985 10 27.075 17 27.165 24 27.235 31 27.315 38 27.385

4 27.005 11 27.085 18 27.175 25 27.245 32 27.325 39 27.395

5 27.015 12 27.105 19 27.185 26 27.265 33 27.335 40 27.405

6 27.025 13 27.115 20 27.205 27 27.275 34 27.345

7 27.035 14 27.125 21 27.125 28 27.285 35 27.355

+ TUNE

- CB LO / DX MODE

DISTANT

+ TUNE

- CB LO / DX MODE

LOCAL

118

CB Radio / ICOM System ICOM System Press and release ICOM on the left control to activate the intercom sys- tem. When the inter- com system is active, ICOM will display on the console screen.

VOX Break Setting The intercom is opened and closed using a voice-operated switch (VOX). The volume sensitivity level required to open the inter- com can be adjusted using the VOX sensi- tivity setting. Press and hold ICOM on the upper left control to access the VOX sensitivity set screen. Push COM or ICOM to adjust the sensitiv- ity setting. Tip: Lower settings require less volume to open

the intercom. If wind or ambient vehicle noise trigger the VOX to open, set the VOX sensitivity to a higher level.

VOX will display on the console screen whenever the driver or passenger are com- municating over the intercom system.

Driver ICOM Volume To change settings, enter the mode menu. Press TUNE (+) or TUNE (-) to adjust settings.

Tip: Intercom volume can also be adjusted with the hand control when the VOX circuit is open.

Passenger ICOM Volume Press (+) or (-) on the headset control to raise or lower volume.

Headset Receptacles The driver's headset receptacle is located on the left side of the motorcycle below the fuel tank. The passenger headset receptacle (if equipped) is located on the left side of the motorcycle on the forward side of the sad- dlebag.

FM ICOM CB19 92.5

COM +/-

ICOM

VOX 15

100.5 FM

VOX CB19

+ TUNE

-

ICOM VOL 15

119

AUX / iPod Getting Started The ignition key must be in the ACC or ON position to use the audio system. Tip: To prevent battery drain, do not leave the

key in the ACC position for long periods. VICTORY recommends using the audio sys- tem only when the engine is running.

Press VOL (+) to turn the audio system on. Press and release the MODE button until AUX or iPod is active. When AUX is active, the console screen will display AUX as the active source.

When iPod is active, the console screen will display iPod as the active source and iPod information in the display screen.

To change the mode, press the MODE button repeatedly to toggle to the AUX mode. Press TUNE (+) or TUNE (-) to set the mode to AUX (for iPod or any other MP3 player use) or to NAV MP3 for navigation unit MP3 player use. Tip: NAV MP3 mode will override any device

connected with an input cable.

iPod Song Control Press and release TUNE (+) or TUNE (-) to change the tracks in the currently selected playlist. Tip: Generic MP3 players can play music, but

cannot be controlled through the audio sys- tem (for example, selecting tracks or playl- ists).

Press and hold TUNE (+) or TUNE (-) to fast-forward or fast-reverse in the currently playing song. A quick double press and release of TUNE (+) or TUNE (-) will bring up a list of songs in the currently selected playlist.

Use TUNE (+) or TUNE (-) to scroll through this song list. The selected song will be in reverse video on the center line of the display. Press and release the PRE but- ton to select and play the highlighted song, or press and release the MODE button to exit without selecting a new song.

AUX ICOM CB19 NAV MP3

iPod ICOM CB19

Artist Song Title

Playlist

+ TUNE

- AUX MODE

AUX

+ TUNE

- AUX MODE NAV MP3

Brown Sugar Gimme Shelter 2

Honky Tonk Woman

+ TUNE

-

120

AUX / iPod iPod Playlists To browse tracks by artist, playlist or album, press and hold the PRE button to bring up the selection screen.Press TUNE (+) or TUNE (-) to highlight the desired category.

Press and release the PRE button to bring up the items in the selected category. When a category is selected, a list of items in that category are displayed with the active track highlighted.

Press TUNE (+) or TUNE (-) to make a selection. Press and release the PRE button to select the highlighted item and play the first track within that item.

Tip: Press and release the MODE button to exit without making a selection.

iPod Tuning Press TUNE (+) or TUNE (-) once to move one track forward or backward. Press and hold the button to advance fast-forward or fast-reverse. Press the button twice (double click) to bring up the track selection screen, then use the TUNE button to move forward and backward through the playlist. When the desired track is highlighted, press and release the PRE button to select the track. Tip: To exit the

screen without changing tracks, press and release the MODE button.

+ TUNE

-

Artist Playlist Album

My Top Rated Road Tunes 2

80s Music

+ TUNE

-

+ TUNE

-

90s Music My iPod

On-The-Go

Track 1 Track 2 Track 3

+ TUNE

-

121

XM Radio About XM Radio XM is North Americas number one satellite radio company, offering an extraordinary variety of commercial-free music, plus the best in premier sports, news, talk radio, comedy, childrens and entertainment pro- gramming, broadcast in superior digital audio quality coast to coast. For more information, or to subscribe, U.S. customers visit xmradio.com or call XM Listener Care at 1-800-XMRADIO (1-800- 967-2346); Canadian customers visit xmra- dio.ca or call XM Listener Care at 1-877- GETXMSR (1-877-438-9677).

XM Ready Legal XM monthly service subscription sold sepa- rately. XM Mini-Tuner and Home Dock required (each sold separately) to receive XM service. It is prohibited to copy, decom- pile, disassemble, reverse engineer, hack, manipulate or otherwise make available any technology or software incorporated in receivers compatible with the XM satellite Radio System. Installation costs and other fees and taxes, including a one-time activa- tion fee may apply. All fees and program- ming subject to change. Channels with frequent explicit language are indicated with an XL. Channel blocking is available for XM radio receivers by calling 1-800- XMRADIO (U.S.residents) and 1-877- GETXMSR (Canadian residents). Only available in the 48 contiguous United States and Canada. 2007 XM Satellite Radio Inc. All rights reserved.

XM Ready Subscription Once you have installed the XM Mini- Tuner Home Dock, inserted the XM Mini- Tuner, connected the XM Mini-Tuner Home Dock to your XM Ready audio system, and installed the antenna, you are ready to sub- scribe and begin receiving XM program- ming. There are three places to find your eight character XM Radio ID: On the XM Mini- Tuner, on the XM Mini-Tuner package, and on XM Channel 0. Record the Radio ID below for reference. Tip: The XM Radio ID does not use the letters I,

O, S or F.

Activate your XM Satellite Radio service in the U.S. online at http://activate.xmra- dio.com or call 1-800-XMRADIO (1-800- 967-2346). Activate your XM Satellite Radio service in Canada online at https:// activate.xmradio.ca or call 1-877-GET- XMSR (1-877-438-9677). You will need a major credit card. XM will send a signal from the satellites to activate the full chan- nel lineup. Activation normally takes 10-15 minutes, but during peak busy periods you may need to keep your XM Ready audio system on for up to an hour. When you can access the full lineup on your XM Ready audio system you are done.

122

XM Radio Getting Started The ignition key must be in the ACC or ON position to use the audio system. Tip: To prevent battery drain, do not leave the

key in the ACC position for long periods. VICTORY recommends using the audio sys- tem only when the engine is running.

Press VOL (+) to turn the audio system on. Press and release the MODE button until the XM radio is the active source.

When the XM radio is active, the console screen will display radio channel, preset number (if applicable), channel name or cat- egory, artist, and song title.

XM Radio Reception If the XM radio system is not receiving a signal due to being indoors (or any overhead obstruction), No Signl appears on the dis- play.

Tip: If the antenna is disconnected, Antenna will display.

XM Radio Menu Options The XM radio system has unique menus that apply only to this system when the XM radio is the active source. Some settings such as bass, treble, fader, etc. apply to both the audio system and the XM radio system. Menus specific to the XM radio system are: XM Display (Category or Channel Name) XM Category (Rock, Country, Traffic, Sports, All Channels, Talk News, etc.) XM Tune Mode (Seek/Scan) Tip: XM Tune Mode is unique to the XM radio

system.

XM Radio Settings To access the menus, turn the audio system power on and change the active source to XM Radio. Press the MODE button repeatedly to toggle to the XM DISPLAY menu. Press TUNE (+) or TUNE (-) to select CAT- EGORY or CHANNEL NAME.

In the CATEGORY mode, the category of a selected station will display in the upper right corner of the screen.

In the CHANNEL NAME mode, the name of the selected channel will display.

XM ICOM CB19

XM ICOM CB19

CH55 P2 CAT Artist

Song Title

ROCK

XM ICOM CB19

CH55 No Signl

+ TUNE

- XM DISPLAY

CHANNEL NAME

+ TUNE

- XM DISPLAY

CATEGORY

XM ICOM CB19

CH55 P2 CAT Artist

Song Title

ROCK

XM ICOM CB19

CH55 Artist

Song Title

CH Name

123

XM Radio XM Radio Categories With XM as the active source, use the MODE button to scroll to the XM Category menu. Press TUNE (+) or TUNE (-) on the left control to change the category.

XM Radio Channels Press TUNE (+) or TUNE (-) on the left control to change the channel. The ALL CHANNELS category must be selected to scroll through every available channel in numerical order. If a specific category (other than ALL CHANNELS) is selected, only channels within that category will be selected with the TUNE button. Tip: If a preset button is used to tune a station

that is not within the currently active cate- gory and the TUNE button is used to change the channel, it will tune stations within the previously selected category, not within the category of the preset station.

+ TUNE

- XM CATEGORY

ALL CHANNELS

124

NAV MP3 Navigation MP3 Introduction Please read this manual and the GARMIN ZUMO 660 NAV MP3 information pro- vided with your player to become familiar with all unit features and operation. The audio integration kit must be installed to enable outputs from the NAV MP3 (such as navigation instructions or user-loaded MP3 media files) to play through the head- sets or speakers. The unit is fully functional without the kit installed, but there will be no interface with the vehicles audio system.

Navigation MP3 Operation Tips Signals coming from the NAV MP3 unit will

override any source of the motorcycles audio system to ensure navigation instructions are communicated when needed. The signals will also override the MP3 player.

You must set volume levels within the NAV MP3 unit. Volume settings in the motorcycles audio system control NAV MP3 volume, but navigation instructions may be difficult to hear if volume levels in the unit are set too low. See the GARMIN information for setting procedures. The recommended initial settings are 100/80/80: MASTER 100%, NAVIGATION 80%, MEDIA 80%.

Pause or stop the MP3 player to switch to radio.

To switch from radio to MP3 player, change the active source to AUX. For best sound quality, change the AUX mode setting on the radio from AUX to NAV MP3 when listening to the MP3 player. Audio works in the AUX setting, but the levels are not optimized.

If playing MP3 files from the GARMIN ZUMO 660 unit, you may need to turn down the media volume on the GARMIN unit to avoid distortion.

Changing to NAV MP3 Mode The ignition key must be in the ACC or ON position to use the audio system. Press VOL (+) to turn the audio system on. Press and release the MODE button until AUX is the active source.

To change the mode, press the MODE button repeatedly to toggle to the AUX mode. Press TUNE (+) or TUNE (-) to set the mode to AUX (for iPod or any other MP3 player use) or to NAV MP3 for navigation unit MP3 player use.

AUX ICOM CB19 AUX

125

Index A

About the Riders Manual. . . . . . . . . . . . . . . . . . . . 5 ABS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 ABS Tone Ring/Sensor Inspection . . . . . . . . . . . . 78 ABS, How to Respond . . . . . . . . . . . . . . . . . . . . . . 8 Accelerating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 Accessories, How to Choose . . . . . . . . . . . . . . . . 10 Air Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60 Anti-Lock Brake System . . . . . . . . . . . . . . . . . . . 32 Anti-Lock Brake System Response . . . . . . . . . . . . 8 Apparel for Riding . . . . . . . . . . . . . . . . . . . . . . . . . 9 Audio Controls . . . . . . . . . . . . . . . . . . . . . . . . . . 106 Audio Memory Presets . . . . . . . . . . . . . . . . . . . . 110 Audio Mode Menus . . . . . . . . . . . . . . . . . . 111-114 Audio Source Selection . . . . . . . . . . . . . . . . . . . 109 Audio Switches . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 Audio System . . . . . . . . . . . . . . . . . . . . . . . . . . . 106 Audio System Power . . . . . . . . . . . . . . . . . . . . . 108 Audio Tuning . . . . . . . . . . . . . . . . . . . . . . . . . . . 110 Audio Volume. . . . . . . . . . . . . . . . . . . . . . . . . . . 108

B Battery

Charging . . . . . . . . . . . . . . . . . . . . . . 82 Installation . . . . . . . . . . . . . . . . . . . . 82 Removal . . . . . . . . . . . . . . . . . . . . . . 81 Safety Warnings . . . . . . . . . . . . . . . . 81

Brake Fluid Level, Front Brake . . . . . . . . . . . . . . 41 Brake Fluid Level, Rear Brake . . . . . . . . . . . . . . . 42 Brake Fluid, Front Brake . . . . . . . . . . . . . . . . . . . 76 Brake Fluid, Rear Brake . . . . . . . . . . . . . . . . . . . . 75 Brake Lever Inspection . . . . . . . . . . . . . . . . . . . . . 41 Brake Lever, Front Brakes . . . . . . . . . . . . . . . 33, 76 Brake Line Inspection . . . . . . . . . . . . . . . . . . . . . . 42 Brake Pad Inspection . . . . . . . . . . . . . . . . . . . . . . 43 Brake Pedal Adjustment . . . . . . . . . . . . . . . . . . . . 33 Brake Pedal Inspection . . . . . . . . . . . . . . . . . . . . . 42 Brake Pedal, Rear Brakes . . . . . . . . . . . . . . . . 33, 75 Brakes

ABS Tone Ring/Sensor Inspection . . 78 Anti-Lock Brake System . . . . . . . . . 32 Brake Fluid Precautions . . . . . . . . . . 75 Brake Lever Inspection . . . . . . . . . . . 41 Brake Line Inspection . . . . . . . . . . . . 42 Brake Pad Inspection . . . . . . . . . . . . 43 Brake Pedal Inspection . . . . . . . . . . . 42 Disc Inspection/Cleaning . . . . . . . . . 77

B Brakes

Front Brake Fluid . . . . . . . . . . . . 41, 76 Front Brake Lever. . . . . . . . . . . . 33, 76 Hoses/Connections . . . . . . . . . . . . . . 78 Rear Brake Fluid. . . . . . . . . . . . . 42, 75 Rear Brake Pedal . . . . . . . . . . . . 33, 75

Braking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 Break-In Maintenance . . . . . . . . . . . . . . . . . . . . . 56 Break-In, Engine. . . . . . . . . . . . . . . . . . . . . . . . . . 46 Breather Hose Inspection . . . . . . . . . . . . . . . . . . . 71

C Cargo Distribution . . . . . . . . . . . . . . . . . . . . . . . . 11 Cargo Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 CB Channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115 CB Headset ENT Mode . . . . . . . . . . . . . . . . . . . 112 CB Headset Volume Controls . . . . . . . . . . . . . . 112 CB Radio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115 CB Radio Frequencies . . . . . . . . . . . . . . . . . . . . 117 CB Radio Mode, Local/Distant . . . . . . . . . . . . . 117 CB Radio Volume, Driver . . . . . . . . . . . . . . . . . 116 CB Radio Volume, Passenger. . . . . . . . . . . . . . . 116 Check Engine Indicator . . . . . . . . . . . . . . . . . 23, 26 Citizens Band (CB) Radio . . . . . . . . . . . . . . . . . 107 Cleaning Products . . . . . . . . . . . . . . . . . . . . . . . . . 93 Clock, Resetting . . . . . . . . . . . . . . . . . . . . . . . 22, 27 Clutch Cable Lubrication, Mechanical . . . . . . . . . 74 Clutch Inspection, Mechanical . . . . . . . . . . . . . . . 43 Clutch Lever . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Clutch Lever Freeplay, Mechanical . . . . . . . . . . . 73 Clutch Lever Lubrication, Mechanical . . . . . . . . . 74 Compliance, Vehicle. . . . . . . . . . . . . . . . . . . . . . . 13 Component Locations

Console . . . . . . . . . . . . . . . . . . . . . . . 18 Left Side . . . . . . . . . . . . . . . . . . . . . . 17 Right Side . . . . . . . . . . . . . . . . . . . . . 17 Top View . . . . . . . . . . . . . . . . . . . . . 18

Console Components . . . . . . . . . . . . . . . . . . . . . . 18 Cruise Control Cable Inspection. . . . . . . . . . . . . . 73 Cruise Control Operation . . . . . . . . . . . . . . . . 51-52

D Deflectors, Fairing . . . . . . . . . . . . . . . . . . . . . . . . 36 Diagnostic Functionality. . . . . . . . . . . . . . . . . . . . 22 Display Units, Standard/Metric . . . . . . . . . . . 22, 27

126

Index D

Drive Belt Cleaning. . . . . . . . . . . . . . . . . . . . . . . 67 Condition . . . . . . . . . . . . . . . . . . . . . . 64 Rear Wheel Alignment . . . . . . . . . . . 67 Tension Adjustment. . . . . . . . . . . . . . 67 Tension Data . . . . . . . . . . . . . . . . . . . 65 Tension Inspection. . . . . . . . . . . . 65-66 Wear Analysis . . . . . . . . . . . . . . . . . . 64

Drive Belt Inspection. . . . . . . . . . . . . . . . . . . . . . 44 Drive Belt/Rear Wheel Alignment . . . . . . . . . . . 67

E Electrical Precautions . . . . . . . . . . . . . . . . . . . . . 89 Elevating the Motorcycle. . . . . . . . . . . . . . . . . . . 90 E-Marks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Engine Break-In. . . . . . . . . . . . . . . . . . . . . . . . . . 46 Engine Compression Test . . . . . . . . . . . . . . . . . . 89 Engine Identification Number . . . . . . . . . . . . . . . 16 Engine Starter Switch . . . . . . . . . . . . . . . . . . . . . 30 Engine Stop/Run Switch . . . . . . . . . . . . . . . . . . . 30 Engine, Starting . . . . . . . . . . . . . . . . . . . . . . . . . . 48 Engine, Stopping . . . . . . . . . . . . . . . . . . . . . . . . . 53 Equipment Modifications . . . . . . . . . . . . . . . . . . 10 Error Codes, Engine. . . . . . . . . . . . . . . . . . . . 23, 26 Exhaust Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Exhaust System Inspection . . . . . . . . . . . . . . . . . 89

F Fairing Deflectors . . . . . . . . . . . . . . . . . . . . . . . . 36 Fairing Vents . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 Fastener Inspection . . . . . . . . . . . . . . . . . . . . 45, 90 Fastener Torques . . . . . . . . . . . . . . . . . . . . . . . . . 90 Floorboard Adjustments . . . . . . . . . . . . . . . . . . . 36 Fluid Change, Engine Oil . . . . . . . . . . . . . . . . . . 59 Fluid Level

Engine Oil . . . . . . . . . . . . . . . . . . . . . 40 Front Brake . . . . . . . . . . . . . . . . . . . . 41 Front Brake Fluid. . . . . . . . . . . . . . . . 76 Rear Brake . . . . . . . . . . . . . . . . . . . . . 42 Rear Brake Fluid . . . . . . . . . . . . . . . . 75

Fork Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . 70 Fuel Cap. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Fuel Gauge. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Fuel Handling Safety . . . . . . . . . . . . . . . . . . . . . . 12 Fuel Level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

F Fuel Recommendation. . . . . . . . . . . . . . . . . . . . . 105 Fuel System Inspection . . . . . . . . . . . . . . . . . . . . . 71 Fuel System, Priming . . . . . . . . . . . . . . . . . . . . . . 47 Fuel Tank Installation . . . . . . . . . . . . . . . . . . . 62-63 Fuel Tank Removal . . . . . . . . . . . . . . . . . . . . . 60-61 Fueling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 Fuse Recommendations. . . . . . . . . . . . . . . . . . . . . 88 Fuse Replacement . . . . . . . . . . . . . . . . . . . . . . . . . 88

G Gasoline Handling Safety . . . . . . . . . . . . . . . . . . . 12 Gear Shift Pedal. . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Gear Shift Pedal Adjustment . . . . . . . . . . . . . . . . . 33 Gear Shifting . . . . . . . . . . . . . . . . . . . . . . . . . . 49-50 Gross Vehicle Weight Rating . . . . . . . . . . . . . . . . 14 GVWR. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

H Hand Grip Heater Switch . . . . . . . . . . . . . . . . . . . 28 Handlebar Position . . . . . . . . . . . . . . . . . . . . . . . . 83 Handlebar Switches, Left . . . . . . . . . . . . . . . . . . . 29 Handlebar Switches, Right . . . . . . . . . . . . . . . . . . 30 Headlight Aim Adjustment . . . . . . . . . . . . . . . . . . 87 Headlight Aim Inspection . . . . . . . . . . . . . . . . . . . 86 Headlight Lamp Replacement . . . . . . . . . . . . . . . . 87 Headset Receptacles . . . . . . . . . . . . . . . . . . . . . . 118 Headset Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115 Heater Switches, Seat . . . . . . . . . . . . . . . . . . . . . . 19

I Identification Number Record . . . . . . . . . . . . . . . 105 Idle Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71 Ignition Key Number. . . . . . . . . . . . . . . . . . . . . . . 16 Ignition Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Ignition Switch Lubrication. . . . . . . . . . . . . . . . . . 82 Indicator Lamps. . . . . . . . . . . . . . . . . . . . . . . . 20, 25 Information Labels . . . . . . . . . . . . . . . . . . . . . 14-15 Instrument Cluster (Cross Country) . . . . . . . . 24-28 Instrument Cluster (Cross Roads) . . . . . . . . . . 20-23 Intercom System . . . . . . . . . . . . . . . . . . . . . 115-118 iPod Playlists . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120 iPod Song Control . . . . . . . . . . . . . . . . . . . . . . . . 119 iPod Tuning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120

K Key Number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

127

Index L

Labels, Information. . . . . . . . . . . . . . . . . . . . . 14-15 Labels, Safety . . . . . . . . . . . . . . . . . . . . . . . . . 14-15 Leather, Rubber and Vinyl Care . . . . . . . . . . . . . . 97 License Plate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 Lock Lubrication. . . . . . . . . . . . . . . . . . . . . . . . . . 82 Locking Saddlebags . . . . . . . . . . . . . . . . . . . . . . . 31 Locking the Trunk . . . . . . . . . . . . . . . . . . . . . . . . 31

M Maintenance

Break-In Maintenance. . . . . . . . . . . . 56 Major Maintenance . . . . . . . . . . . . . . 56 Periodic Maintenance . . . . . . . . . 56-57

Maintenance for Safety . . . . . . . . . . . . . . . . . . . . . 13 Maintenance Log . . . . . . . . . . . . . . . . . . . . . . . . . 58 Maintenance Safety. . . . . . . . . . . . . . . . . . . . . . . . 55 Maintenance, Required . . . . . . . . . . . . . . . . . . . . . 13 Major Maintenance . . . . . . . . . . . . . . . . . . . . . . . . 56 Metric Display . . . . . . . . . . . . . . . . . . . . . . . . 22, 27 MFD . . . . . . . . . . . . . . . . . . . . . . . . . . . 21-23, 26-28 Mode Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 Modifications, Vehicle . . . . . . . . . . . . . . . . . . . . . 10 Motorcycle Safety Foundation . . . . . . . . . . . . . . . . 6 MP3 Player . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124 Multi-Function Display. . . . . . . . . . . . . 21-23, 26-28

N Navigation MP3 . . . . . . . . . . . . . . . . . . . . . . . . . 124

O Odometer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Oil Change, Engine Oil/Filter . . . . . . . . . . . . . . . . 59 Oil Level, Engine Oil . . . . . . . . . . . . . . . . . . . . . . 40 Oil Recommendation . . . . . . . . . . . . . . . . . . . . . 105

P Parking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 Parking on a Slope . . . . . . . . . . . . . . . . . . . . . . . . 53 Parking on a Soft Surface . . . . . . . . . . . . . . . . . . . 53 Parking the Motorcycle. . . . . . . . . . . . . . . . . . . . . 10 Passenger Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Pedal Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . 33 Periodic Maintenance . . . . . . . . . . . . . . . . . . . 56-57 Polished Aluminum Care . . . . . . . . . . . . . . . . . . . 95 Polishing the Motorcycle . . . . . . . . . . . . . . . . 95-97 Protectants, Leather, Rubber, Vinyl . . . . . . . . . . . 97 Push-to-Talk (PTT). . . . . . . . . . . . . . . . . . . . . . . 116

R Radio Frequencies . . . . . . . . . . . . . . . . . . . . . . . 106 Radio Frequencies, CB . . . . . . . . . . . . . . . . . . . . 117 Rear Axle Inspection . . . . . . . . . . . . . . . . . . . . . . 69 Refueling Safety . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Reverse Operation . . . . . . . . . . . . . . . . . . . . . . . . 54 Riding Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-9 Road Testing. . . . . . . . . . . . . . . . . . . . . . . . . . 56, 90

S Saddlebag Bumpers . . . . . . . . . . . . . . . . . . . . . . . 85 Saddlebag Lock . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Saddlebags, Using Safely . . . . . . . . . . . . . . . . . . . 11 Safety Gear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Safety Labels . . . . . . . . . . . . . . . . . . . . . . . . . 14-15 Safety Symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Safety While Servicing . . . . . . . . . . . . . . . . . . . . . 55 Seat Removal/Installation. . . . . . . . . . . . . . . . . . . 86 Service Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . 92 Service Procedure Safety . . . . . . . . . . . . . . . . . . . 55 Shift Points . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 Shifting Gears . . . . . . . . . . . . . . . . . . . . . . . . . 49-50 Side Covers, Removal/Installation . . . . . . . . . . . . 84 Sidestand. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 Sidestand Inspection . . . . . . . . . . . . . . . . . . . . . . . 45 Sidestand Lubrication . . . . . . . . . . . . . . . . . . . . . . 82 Signal Words . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Spark Plugs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80 Speedometer . . . . . . . . . . . . . . . . . . . . . . . . . . 20, 24 Squelch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116 Starter Interlock Switch . . . . . . . . . . . . . . . . . . . . 29 Steering Head Inspection . . . . . . . . . . . . . . . . . . . 70 Steering Inspection . . . . . . . . . . . . . . . . . . . . . . . . 44 Storage

Battery Care . . . . . . . . . . . . . . . . . . . 99 Clean/Protect the Motorcycle . . . . . . 98 Engine Protection . . . . . . . . . . . . . . . 99 Fuel Stabilizer . . . . . . . . . . . . . . . . . . 98 Maintenance During . . . . . . . . . . . . . 99 Motorcycle Cover . . . . . . . . . . . . . . . 99 Removal From . . . . . . . . . . . . . . . . 100 Rodents . . . . . . . . . . . . . . . . . . . . . . . 99 Storage Area . . . . . . . . . . . . . . . . . . . 98 Tire Inflation. . . . . . . . . . . . . . . . . . . 98

Storage Compartments . . . . . . . . . . . . . . . . . . . . . 35 Suspension Adjustment, Rear . . . . . . . . . . . . . 68-69 Suspension Inspection, Front . . . . . . . . . . 44, 69-70 Suspension Inspection, Rear . . . . . . . . . . . . . . . . . 44

128

Index S

Swing Arm Inspection . . . . . . . . . . . . . . . . . . . . . 69 Switches

Audio Switches . . . . . . . . . . . . . . . . . 29 Emergency Flasher Switch . . . . . . . . 29 Engine Starter Switch . . . . . . . . . . . . 30 Engine Stop/Run Switch . . . . . . . . . . 30 Hand Grip Heater Switch. . . . . . . . . . 28 Hazard Switch . . . . . . . . . . . . . . . . . . 29 High Beam/Low Beam Switch . . . . . 29 Horn Button . . . . . . . . . . . . . . . . . . . . 29 Ignition Switch . . . . . . . . . . . . . . . . . 19 Ignition Switch Lubrication. . . . . . . . 82 Mode Button . . . . . . . . . . . . . . . . . . . 29 Seat Heater Switches . . . . . . . . . . . . . 19 Sidestand Interlock Switch . . . . . . . . 34 Starter Interlock Switch . . . . . . . . . . . 29 Turn Signal Switch . . . . . . . . . . . . . . 29

Switches, Console (Cross Country). . . . . . . . . . . 28 Switches, Left Handlebar. . . . . . . . . . . . . . . . . . . 29 Switches, Right Handlebar . . . . . . . . . . . . . . . . . 30

T Tachometer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Testing After Servicing . . . . . . . . . . . . . . . . . 56, 90 Throttle Cable Freeplay . . . . . . . . . . . . . . . . . . . . 72 Throttle Cable Lubrication . . . . . . . . . . . . . . . . . 73 Throttle Control Grip. . . . . . . . . . . . . . . . . . . . . . 31 Throttle Control Inspection . . . . . . . . . . . . . . . . . 72 Throttle Freeplay . . . . . . . . . . . . . . . . . . . . . . . . . 43 Throttle Inpspection. . . . . . . . . . . . . . . . . . . . . . . 43 Tilt Sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 Tires

Condition . . . . . . . . . . . . . . . . . . . . . . 79 Pressure . . . . . . . . . . . . . . . . . . . . . . . 80 Recommended Pressure. . . . . . . . . . . 80 Recommended Type . . . . . . . . . . . . . 80 Tire Condition . . . . . . . . . . . . . . . . . . 41 Tire Pressure . . . . . . . . . . . . . . . . . . . 41 Tire Replacement Standard . . . . . . . . 79 Tire Tread Depth . . . . . . . . . . . . . . . . 41 Tread Depth . . . . . . . . . . . . . . . . . . . . 79 Wheel Inspection . . . . . . . . . . . . . . . . 78

T Tone Ring/Sensor Inspection, ABS. . . . . . . . . . . . 78 Tool Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 Transporting the Motorcycle . . . . . . . . . . . . . . . . . 12 Trip Odometer . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . 91-92 Trunk Door Lock. . . . . . . . . . . . . . . . . . . . . . . . . . 31 Trunk Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . 84 Trunk, Using Safely. . . . . . . . . . . . . . . . . . . . . . . . 11 Turn Signal Switch . . . . . . . . . . . . . . . . . . . . . . . . 29

V Vents, Fairing . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 VICTORY Cleaning Products . . . . . . . . . . . . . . . . 93 VIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Volt Meter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

W Washing the Motorcycle . . . . . . . . . . . . . . . . . 93-95 Weather Band (WX) . . . . . . . . . . . . . . . . . . . . . . 114 Weight Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Wheel Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . 78 Wheel Spoke Inspection . . . . . . . . . . . . . . . . . . . . 78

X XM Radio Categories . . . . . . . . . . . . . . . . . . . . . 123 XM Radio Channels

Manualsnet FAQs

If you want to find out how the Victory Cross Roads Polaris works, you can view and download the Polaris Cross Roads,Hard Ball,Tour Owner's Manual on the Manualsnet website.

Yes, we have the Owner's Manual for Polaris Victory Cross Roads as well as other Polaris manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Owner's Manual should include all the details that are needed to use a Polaris Victory Cross Roads. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Polaris Cross Roads,Hard Ball,Tour Owner's Manual is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Polaris Cross Roads,Hard Ball,Tour Owner's Manual consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Polaris Cross Roads,Hard Ball,Tour Owner's Manual free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Polaris Cross Roads,Hard Ball,Tour Owner's Manual, simply download the document to your computer. Once downloaded, open the PDF file and print the Polaris Cross Roads,Hard Ball,Tour Owner's Manual as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.