Polaris Sportsman Forest 500 Owner's Manual PDF

1 of 138
1 of 138

Summary of Content for Polaris Sportsman Forest 500 Owner's Manual PDF

Owner's Manual for Maintenance and Safety

Read this manual carefully. It contains important safety information. This is an adult vehicle only.

Operation is prohibited for those under 16 years of age.

Sportsman Forest 500

For your nearest Polaris dealer, call 1-800-POLARIS or visit www.polarisindustries.com Polaris Sales Inc., 2100 Hwy 55 Medina, MN 55340 Phone 1-888-704-5290 Part No. 9923174 Rev 01 Printed in USA *9923174 *

Before you operate this vehicle, read the owners manual

1

WELCOME Thank you for purchasing a POLARIS vehicle, and welcome to our world-wide family of POLARIS owners. We proudly produce an excit- ing line of utility and recreational products. Snowmobiles All-terrain vehicles (ATVs) RANGER utility vehicles Victory motorcycles Always follow the instructions and recommendations in this manual. The manual contains instructions for minor maintenance, but informa- tion about major repairs is outlined in the POLARIS Service Manual and should be performed only by a factory certified Master Service Dealer (MSD) technician. Please see your dealer for all of your service needs during (and after) the warranty period. For more information about POLARIS, visit us online at www.polarisindustries.com.

2

POLARIS, THE WAY OUT and SPORTSMAN are registered trademarks of POLARIS Industries Inc. Copyright 2010 POLARIS Sales Inc. All information contained within this publication is based on the latest product information at the time of publication. Due to constant improvements in the design and quality of production components, some minor discrep- ancies may result between the actual vehicle and the information presented in this publi- cation. Depictions and/or procedures in this publication are intended for reference use only. No liability can be accepted for omissions or inaccuracies. Any reprinting or reuse of the depictions and/or procedures contained within, whether whole or in part, is expressly prohibited. The original instructions for this vehicle are in English. Other languages are provided as translations of the original instructions. Printed in U.S.A. SPORTSMAN Forest 500 Owners Manual P/N 9923174

3

TABLE OF CONTENTS Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Features and Controls . . . . . . . . . . . . . . . . . . . 34 Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 Winch Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . 56 Emission Control Systems . . . . . . . . . . . . . . . 62 Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . 63 Specifications. . . . . . . . . . . . . . . . . . . . . . . . . 120 POLARIS Products. . . . . . . . . . . . . . . . . . . . . 122 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . 123 Declaration of Conformity . . . . . . . . . . . . . . . 127 Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128 Maintenance Log . . . . . . . . . . . . . . . . . . . . . . 131 Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134

4

INTRODUCTION The following signal words and symbols appear throughout this manual and on your vehicle. Your safety is involved when these words and sym- bols are used. Become familiar with their meanings before reading the manual.

The safety alert symbol indicates a potential personal injury hazard.

DANGER A DANGER indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.

WARNING A WARNING indicates a hazardous situation which, if not avoided, may result in death or serious injury.

CAUTION A CAUTION indicates a hazardous situation which, if not avoided, may result in minor or moderate injury.

NOTICE A NOTICE indicates a situation that may result in property damage.

The Prohibition Safety Sign indicates an action NOT to take in order to avoid a hazard.

The Mandatory Action Sign indicates an action that NEEDS to be taken to avoid a hazard.

5

INTRODUCTION

Failure to follow the warnings in this manual can result in serious injury or death. This POLARIS vehicle is not a toy and can be hazardous to operate. A collision or rollover can occur quickly, even during routine maneuvers, if you fail to take proper precautions.

Read and understand your owner's manual and all warnings before operating this POLARIS vehicle.

Safety Training When you purchased your new POLARIS vehicle, your dealer offered a hands-on safety training course. You were also provided with printed materials that explain safe operating procedures. Review this informa- tion on a regular basis. If you purchased a used POLARIS vehicle from a party other than a POLARIS dealer, please request free safety training from any autho- rized POLARIS dealer.

Age Restrictions This vehicle is an ADULT VEHICLE ONLY. Operation is prohibited for anyone under 16 years of age.

Restrictions This vehicle is approved for OFF-ROAD TOWING ONLY. Towing a trailer with this vehicle on public roads is prohibited.

Equipment Modifications The warranty on your POLARIS vehicle may be terminated if any equipment has been added, or if any modifications have been made, that increase speed or power. The addition of certain accessories, including (but not limited to) mowers, blades, tires, sprayers and large racks may change vehicle handling. Use only POLARIS-approved accessories. Know their function and effect on the vehicle.

WARNING

6

INTRODUCTION Vehicle Identification Numbers Record your vehicle's identification numbers and key number in the spaces provided. Remove the spare key and store it in a safe place. An ignition key can be duplicated only by ordering a POLARIS key blank (using your key number) and mating it with one of your existing keys. The ignition switch must be replaced if all keys are lost.

Vehicle Model Number: ___________________________________________________

Frame VIN: ____________________________________________________________

Engine Serial Number: ___________________________________________________

Key Number: ___________________________________________________________

VIN (front or rear frame) ####

Engine Serial Number

Key Number

7

SAFETY Operator Safety

Serious injury or death can result if you do not follow the instructions and procedures listed here and throughout this manual.

Read and understand all warnings, cautions and operating procedures in this manual and on the safety labels before operating the vehicle.

Never operate this vehicle without proper instruction. Take a training course. Beginners should receive training from a certified instructor. Contact an authorized POLARIS dealer or visit the POLARIS web site at www.polarisindustries.com.

Never permit others to operate the vehicle unless they have read and understand this manual and all product labels, and have completed a certified safety training course.

Never allow anyone under 16 years of age to operate this vehicle.

Never carry a passenger. The purpose of the long seat is to allow the operator to shift position.

WARNING

8

SAFETY Operator Safety

Always wear an approved helmet that fits properly. Wear eye protection (goggles or face shield), gloves, boots, long sleeves and long pants.

Never consume alcohol or drugs before or while operating this vehicle.

Never operate at excessive speeds. Travel and turn at speeds appropriate for the terrain, visibility, operating conditions and your experience.

Never attempt jumps or other stunts.

9

SAFETY Operator Safety

Always inspect your POLARIS vehicle before each use to verify that it's in safe operating condition. Follow the inspection and maintenance procedures outlined in this manual. See page 53.

Keep both hands on the handlebars. Keep your feet on the footrests.

Always travel slowly when operating on unfamiliar terrain. Use extra caution.

Always follow the procedures outlined in this manual for turning. See page 19.

Never turn sharply at excessive speeds, which can lead to vehicle overturn.

10

SAFETY Operator Safety

If the vehicle has been involved in an accident, always have an authorized POLARIS dealer inspect the entire vehicle for possible damage, including (but not limited to) brake, throttle and steering systems.

Never operate on hills too steep for the vehicle or for your abilities. Practice on smaller hills before attempting larger hills. Avoid climbing hills steeper than 25. Always follow the procedures outlined in this manual for driving on hills. See page 22.

Always follow the procedures outlined in this manual for driving downhill and for braking on hills. See page 25.

Always follow the procedures outlined in this manual for crossing the side of a hill. See page 24.

Never attempt to turn the vehicle around on any hill until you've mastered (on level ground) the turning technique outlined in this manual.

11

SAFETY Operator Safety

Always follow the procedures outlined in this manual for braking if you stall or roll backwards while climbing a hill. Never back down a hill. See page 26.

Always follow the procedures outlined in this manual for operating over obstacles. See page 21.

Always follow the procedures outlined in this manual for operating on slippery or loose surfaces. Use extra caution. Always avoid skidding or sliding. See page 20.

Always follow the procedures outlined in this manual for driving through water. Never drive through deep or fast-flowing water. See page 28.

12

SAFETY Operator Safety

Always follow the procedures outlined in this manual for driving in reverse. See page 31.

Always use the size and type of tires specified for your vehicle. Maintain the proper tire pressure.

Never modify this POLARIS vehicle through improper installation or use of accessories.

Never exceed the stated load capacity for your vehicle. Cargo must be properly distributed and securely attached. Reduce speed and follow the instructions in this manual for carrying cargo or towing. Allow a greater distance for braking.

13

SAFETY Operator Safety

Never operate the vehicle on a frozen body of water unless you have independently verified that the ice is sufficiently thick to support the weight and moving force of the vehicle, you and your cargo, together with any other vehicles in your party.

Operating on paved surfaces may affect the handling and control of the vehicle and could result in loss of control. Avoid sudden turns or swift movement of the handlebars.

Always remove the ignition key when the vehicle is not in use to prevent unauthorized use or accidental starting.

Always unlock the steering before starting the engine. See page 40.

Hot components can cause serious burns and fire. Do not touch hot exhaust system components. Always keep combustible materials away from the exhaust system.

For more information about safety, contact an authorized POLARIS dealer or visit the POLARIS web site at

www.polarisindustries.com.

14

SAFETY Safety Labels and Locations Warning labels have been placed on the vehicle for your protection. Read and follow the instructions on each label carefully. If a label becomes illegible or comes off, contact your POLARIS dealer to pur- chase a replacement. Replacement safety labels are provided by POLARIS at no charge. The part number is printed on the label. The following pages repeat the information found on each label.

General Alert (Multi-Lingual) Before you operate this vehicle, read the owners manual.

Hill Operation Alert Never operate this vehicle on HILLS

steeper than 25 degrees 25. To prevent flip-over on hilly terrain,

when going up or down, use throttle and brakes gradually.

General Alert

Hill Operation

Alert

Age 16 Alert

15

SAFETY Safety Labels and Locations

No Passenger Warning WARNING - NEVER ride as a passenger. Passengers can cause a loss of control, resulting in SEVERE INJURY or DEATH.

Tire Pressure/Load Alert TIRE PRESSURE IN PSI (KPa): FRONT 5 (34.5) REAR 5 (34.5)

MAXIMUM WEIGHT CAPACITY (Gross Vehicle Weight) INCLUDING MACHINE, DRIVER AND CARGO IS 1200 LBS. (546 kg). Read Owner's Manual for more detailed loading information.

Clutch Cover Alert NO STEP

Rack Warning, Front and Rear WARNING - DO NOT TOW FROM RACK OR BUMPER. Vehicle damage or tipover may result causing severe injury or death. Tow only from tow hooks or hitch. Maximum Rack Loads: Front 90 lbs. (41 kg) Rear 180 lbs. (82 kg)

Reverse Override Alert Pushing reverse override button may cause sudden increases in power and traction if too much throttle is applied. Loss of control or forward flipover may result, especially in AWD. See Owner's Manual.

No Passenger WarningRack

Warning Rack

Warning

Tire Pressure/ Load AlertClutch Cover Alert

16

SAFETY Safe Riding Gear Always wear protective clothing to reduce the chance of injury.

Helmet Always wear a helmet that meets or exceeds established safety stan- dards. Approved helmets in the USA and Canada bear a U.S. Department of Transportation (DOT) label. Approved helmets in Europe, Asia and Oceania bear the ECE 22.05 label. The ECE mark consists of a circle surrounding the letter E, followed by the distinguishing number of the country which has granted approval. The approval number and serial number will also be displayed on the label.

Helmet Eye Protection

Gloves

Boots

Long Pants

Long Sleeves

E4

051039 0006.31

17

SAFETY Safe Riding Gear Eye Protection Do not depend on eyeglasses or sunglasses for eye protection. When- ever riding a POLARIS vehicle, always wear shatterproof goggles or use a shatterproof helmet face shield. POLARIS recommends wearing approved Personal Protective Equipment (PPE) bearing markings such as VESC 8, V-8, Z87.1, or CE. Make sure protective eye wear is kept clean. Gloves Off-road style gloves with knuckle pads are the best for comfort and protection. Boots The best footwear is a pair of sturdy over-the-calf boots with low heels. Clothing Always wear long sleeves and long pants to protect arms and legs. Riding pants with kneepads and a jersey with shoulder pads provide the best protection.

18

SAFETY Driving Safely Driving Procedures

1. Sit upright. Keep your feet on the footrests. Keep both hands on the handlebars.

2. Apply the brakes. 3. Start the engine and allow it to warm up. 4. Shift the transmission into gear. 5. Check your surroundings and determine your path of travel. 6. Release the brakes. 7. Slowly squeeze the throttle lever toward the handlebar to begin

driving. 8. Drive slowly. Practice maneuvering and using the throttle and

brakes on level surfaces.

19

SAFETY Driving Safely Turning the Vehicle 1. Before turning, activate

a turn signal to alert others of your inten- tions. Activate the left signal before a left turn. Activate the right signal before a right turn.

2. Steer in the direction of the turn, leaning your upper body to the inside of the turn while supporting your weight on the outer footrest. Use the same leaning technique for turning in reverse.

3. Practice turning at slow speeds before attempting to turn at faster speeds.

Always follow the procedures outlined in this manual for turning. Never turn sharply at excessive speeds, which can lead to vehicle overturn.

20

SAFETY Driving Safely Driving on Slippery Surfaces Whenever driving on slippery or loose surfaces such as wet trails, gravel, snow or ice, follow these precautions: 1. Slow down before

driving onto slippery surfaces.

2. Engage AWD before wheels begin to lose traction.

3. Be alert. Watch the trail. Avoid quick, sharp turns.

Tip: To correct a rear wheel skid, turn the handle- bars in the same direc- tion as the skid and shift body weight forward.

NOTICE: Severe damage to the drive train may occur if AWD is engaged while the wheels are spinning. Engage AWD when the wheels have traction.

Always follow the procedures outlined in this manual for operating on slippery or loose surfaces. Use extra caution. Always avoid skidding or sliding.

Sideways skid

Turn in direction of skid

21

SAFETY Driving Safely Driving Over Obstacles

1. Always check for obstacles before operating in a new area. Serious injury or death can result if your vehicle comes in contact with a hidden obstacle.

2. Be alert. Watch the terrain. Use extra caution. 3. Never operate over large obstacles. 4. Avoid hazards such as logs, rocks and low branches.

Always follow the procedures outlined in this manual for operating over obstacles.

22

SAFETY Driving Safely Driving Uphill

Whenever traveling uphill, follow these precautions: 1. Avoid steep hills (25 maximum). 2. Check the terrain carefully. 3. Avoid hills with excessively slippery or loose surfaces. 4. Shift your weight uphill. 5. Drive straight uphill. 6. Keep your feet on the footrests. 7. Drive at a steady rate of speed to avoid stalling.

8. Be alert. Be prepared to take emergency action. This may include dismounting quickly.

9. Never open the throttle suddenly or make sudden gear changes. 10. Never go over the top of a hill at high speed.

25 Maximum

23

SAFETY Driving Safely Driving Uphill If all forward speed is lost: Keep your weight uphill. If the vehicle begins rolling downhill, never apply engine power. Never apply the brakes aggressively while rolling backwards. Apply the brakes gradually. When fully stopped, lock the hydraulic parking brake. See page 39. Dismount on the uphill side, or to either side if the vehicle is pointed straight uphill. Turn the vehicle around using the K-Turn. See page 26.

Always follow the procedures outlined in this manual for climbing hills. Avoid climbing hills steeper than 25.

Always follow the procedures outlined in this manual for braking if you stall or roll backwards while climbing a hill. Never back down a hill.

24

SAFETY Driving Safely Driving on a Sidehill (Sidehilling)

Avoid crossing the side of a hill (sidehilling) if possible. If sidehilling is necessary, follow these precautions: 1. Slow down. 2. Avoid hills with excessively slippery or loose surfaces. 3. Shift your weight uphill. 4. Avoid crossing the sides of steep hills. 5. Keep your feet on the footrests. 6. Steer slightly into the hill. 7. If the vehicle begins to tip, quickly turn the front wheels downhill

(if possible) or dismount on the uphill side immediately!

Always follow the procedures outlined in this manual for crossing the side of a hill.

Never attempt to turn the vehicle around on any hill until you've mastered (on level ground) the turning technique outlined in this manual.

25

SAFETY Driving Safely Driving Downhill When driving downhill, follow these precautions:

1. Check the terrain carefully. 2. Avoid hills with

excessively slippery or loose surfaces.

3. Never drive downhill at high speed.

4. Slow down. 5. Avoid driving downhill at

an angle, which can cause the vehicle to pitch sharply to one side. Drive straight downhill.

6. Shift your weight rearward. 7. Apply the brakes slightly to aid in slowing.

Always follow the procedures outlined in this manual for driving downhill and for braking on hills.

Never operate at excessive speeds. Travel and turn at speeds appropriate for the terrain, visibility, operating conditions and your experience.

26

SAFETY Driving Safely Turning Around on a Hill (K-Turn) If the vehicle stalls while climbing a hill, never back it down the hill! Use the K-turn to turn around.

1. Stop the vehicle. Keep your weight uphill. 2. Lock the hydraulic parking brake. 3. Leave the transmission in forward gear. Turn the engine off. 4. Dismount on the uphill side of the vehicle, or on the left if the vehi-

cle is pointing straight uphill. 5. Stay uphill of the vehicle and turn the handlebars full left. 6. Squeeze the brake lever to release the parking brake. 7. Slowly release the brake lever and allow the vehicle to roll around

to your right until it's pointing across the hill or slightly downward.

2.4 m

27

SAFETY Driving Safely Turning Around on a Hill (K-Turn) 8. Lock the hydraulic parking brake. 9. Remount from the uphill side. Keep your weight uphill. 10. Apply the foot brake. 11. With the transmission still in forward, start the engine. 12. Squeeze and release the brake lever to release the parking brake. 13. Release the foot brake and drive slowly downhill. Control speed

with either the hand or foot brake until the vehicle is on level ground.

Always follow the procedures outlined in this manual for climbing hills. See page 22.

Always follow the procedures outlined in this manual for braking if you stall or roll backwards while climbing a hill. Never back down a hill.

28

SAFETY Driving Safely Driving Through Water

Follow these procedures when driving through water: 1. Check water depth and current before crossing. 2. Avoid operating in water deeper than the bottom of the footrests. If

it's unavoidable, travel slowly, balance your weight carefully and avoid sudden movements. Maintain a slow and steady forward motion. Do not make sudden turns, stops or throttle changes.

3. Choose a crossing where both banks have gradual inclines. 4. Drive slowly. Avoid rocks and obstacles. 5. Wet brakes may have reduced stopping ability. Always test your

brakes after leaving water. If necessary, apply them lightly several times to allow friction to dry out the pads.

Maximum Depth

29

SAFETY Driving Safely Driving Through Water If your vehicle becomes fully immersed, and it's impossible to take it to a dealer before starting it, follow the steps described on page 100. Have the vehicle serviced by your dealer promptly. If water has been ingested into the transmission (PVT), follow the pro- cedure on page 105.

Always follow the procedures outlined in this manual for driving through water. Never drive through deep or fast-flowing water.

If the vehicle stops while fully submerged, major engine damage can result if the machine is not thoroughly inspected. Take the vehicle to your dealer before starting the engine.

30

SAFETY Driving Safely Parking on an Incline

Avoid parking on an incline. If it's unavoidable, follow these precau- tions: 1. Stop the engine. 2. Place the transmission in PARK. 3. Always block the rear wheels on the downhill side. 4. Turn the fuel valve off.

31

SAFETY Driving Safely Driving in Reverse

Follow these precautions when operating in reverse: 1. Avoid backing downhill. 2. Always check for obstacles or people behind the vehicle before

backing. 3. Drive slowly. 4. Apply the foot brake lightly for stopping. 5. Avoid turning at sharp angles. 6. Do not use the override switch unless additional power is required

for vehicle movement. Use with caution. Tip: Reverse speed is greatly increased when the override switch is used. Do

not operate at full throttle. Apply just enough throttle to maintain the desired speed.

Excessive throttle operation while in the speed limit mode may cause fuel to build in the exhaust, resulting in engine popping and/or engine damage.

Always follow the procedures outlined in this manual for driving in reverse.

32

SAFETY Driving Safely Hauling Cargo

Overloading the vehicle or carrying or towing cargo improperly can alter vehicle handling and may cause loss of control or brake instability. Always follow these precautions when hauling cargo.

Read and understand the load distribution warnings listed on the vehicle warning labels.

Never exceed the stated load capacity for this vehicle.

REDUCE SPEED AND ALLOW GREATER DISTANCES FOR BRAKING WHEN HAULING CARGO OR TOWING. Use extreme caution when applying brakes. Avoid situations that require backing downhill.

When operating over rough or hilly terrain, reduce speed, cargo and towed load to maintain stable driving conditions.

DO NOT BLOCK THE FRONT HEADLIGHT BEAM when carrying loads on the front rack.

CARRY LOADS AS LOW ON THE RACK AS POSSIBLE. Carrying a load high on the rack raises the center of gravity of the vehicle and creates a less stable operating condition. Reduce load weight when cargo is high. Secure off-centered loads that cannot be centered and operate with extra caution.

CARRYING A LOAD on only one rack may cause the vehicle to overturn. Split the load between the front rack and rear rack, with 1/3 in the front and 2/ 3 in the back. Do not exceed load capacities. See specifications beginning on page 120.

SECURE ALL LOADS BEFORE OPERATING. Unsecured loads can create unstable operating conditions, which could result in loss of control of the vehi- cle.

OPERATE ONLY WITH STABLE AND SAFELY ARRANGED LOADS. When handling off-centered loads that cannot be centered, securely fasten the load and operate with extra caution. Always attach the tow load to the hitch point designated for your vehicle.

USE EXTREME CAUTION when operating with loads that extend over the rack sides. Stability and maneuverability may be adversely affected, causing the vehicle to overturn.

TOWING is approved OFF-ROAD ONLY. Operating this vehicle with a trailer on public roads is prohibited.

TOWING SPEED should never exceed 16 km/h. Never exceed 8 km/h when towing loads in rough terrain, while cornering, or while ascending or descend- ing hills.

33

SAFETY Driving Safely Hauling Cargo

Towing Loads Towing is approved OFF-ROAD ONLY. Operating this vehicle with a trailer on public roads is prohibited. Do not exceed the maximum capac- ities when towing. Do not tow any trailer on a grade steeper than 15.

Using an improper hitch or exceeding the maximum tongue weight capacity can result in serious damage to the vehicle and will void your warranty. Never install a hitch longer than 17 cm. Never install automotive accessories on your POLARIS vehicle. Always install POLARIS-approved (or equivalent) accessories designed for use on the vehicle.

1/3 2/3

Maximum 17 cm

34

FEATURES AND CONTROLS Switches

Mode/Reverse Override Switch Press the switch to toggle through the speedometer display modes (except in reverse). See page 45. To gain additional power while operating in reverse, press the override switch before opening the throttle. This will cancel the reverse speed limit function. The override switch also allows activation of All Wheel Drive in reverse, if the AWD switch is on.

Activating the override switch with the throttle open and while operating in reverse can cause loss of control. Do not activate the override switch while the throttle is open.

Momentary High Beam Switch Press this switch with your left forefinger to activate the headlight high beam. The lights will return to low beam when the switch is released.

All Wheel Drive Switch See page 44 for all wheel drive information.

Winch Switch See page 56 for winch information.

Mode/Reverse Override Switch

Main Key Switch

All Wheel Drive Switch

Choke

Winch Switch

Momentary High-Beam Switch

35

FEATURES AND CONTROLS Switches Main Key Switch

End all electrical power to the vehicle.

LIGHTS ON position turns the headlights on.

Start the engine. The headlights are not on in this position.

After starting the engine, release the key switch to the POSITION LIGHTS ON position.

See page 54 for starting procedures.

Engine Stop Switch The engine will not start or run when the switch is in the OFF position.

OFF

RUN

Headlight Switch The lights do not operate unless the main key switch is on and the engine stop switch is in the RUN position.

High Beam

Low Beam

Override Switch

Engine Stop

Switch Headlight

Switch

Horn Switch

Hazard Switch

Turn Signal Switch

36

FEATURES AND CONTROLS Switches Turn Signal Switch

Push the toggle switch either left or right to activate the corresponding turn sig- nal light. The indicator on the pod will also flash. Return the toggle to the center posi- tion to end the signal.

Horn Switch

Press the horn switch to sound the horn.

Hazard Warning Switch

Push the hazard warning switch to cause all turn signal lights to flash simulta- neously. Use this feature to alert others of an emergency or other situation requiring caution.

Horn Switch

Hazard Switch

Turn Signal Switch

37

FEATURES AND CONTROLS Mirrors Use the mirrors to assist in traffic maneuvers. Always check and adjust the mirrors before driving the vehicle.

Throttle Lever

Failure to check or maintain proper operation of the throttle system can result in an accident if the throttle lever sticks during operation. Check the lever for proper operation before starting the engine. Check occasionally during operation.

Do not start or operate a vehicle with sticking or improperly operating throttle controls. Contact your dealer for repair if throttle problems arise.

Press the throttle lever to increase engine speed and vehicle movement. Release the lever to reduce engine speed and vehicle movement.

Electronic Throttle Control (ETC) ETC causes the engine to stop if the throttle cable sticks in an open posi- tion when the operator releases the throttle lever.

The Electronic Throttle Control (ETC) stops the engine in the event of a throttle system malfunction. Do not modify the ETC system or replace it with other throttle mechanisms.

Electronic Throttle Control

38

FEATURES AND CONTROLS Foot Brake The all-wheel foot brake is located on the right footrest. The foot brake operates both front and rear brakes. Press the brake pedal down with your foot to apply the all-wheel brakes. If the rear wheels begin to skid or slide while using the foot brake, reduce brake pressure.

Hand Brake Lever The hand brake operates both front and rear brakes. Squeeze the brake lever toward the handlebar to apply the all-wheel brakes. If the rear wheels begin to skid or slide while using the brake, reduce lever pressure.

Aggressively applying the brakes when backing down a hill may cause rear tipover. Aggressively applying the brakes while moving forward may cause the rear wheels to skid and result in loss of control.

Read this owner's manual and understand the operation of all brake systems on this vehicle. Always use caution whenever applying the brakes.

Foot Brake

39

FEATURES AND CONTROLS Parking Brake Locking the Parking Brake 1. Place the transmission in

PARK. 2. Squeeze the brake lever

toward the handlebar. 3. Push the parking brake lock

forward to engage the lock. 4. Release the brake lever. 5. To release the parking brake

lock, squeeze and release the brake lever.

Operating the vehicle while the parking brake is engaged could result in an accident and serious injury or death. Always release the parking brake lock before operating.

40

FEATURES AND CONTROLS Steering Lock Lock the steering to prevent unau- thorized use or theft of the vehicle. Tip: Place the steering lock keys in a

safe place. The lock must be replaced if the keys are lost.

1. Turn the handlebars to the full left position.

2. Insert the steering lock key and turn it clockwise.

3. Remove the key. 4. Reverse the procedure to

unlock the steering.

The handlebars are locked in the full left position when the steering is locked. Always unlock the steering before starting the engine.

41

FEATURES AND CONTROLS Fuel Valve The fuel valve is located under the front storage box cover. OFF: For vehicle storage and when transporting. ON: For normal operation.

Choke The choke assists in starting a cold engine. Refer to the engine starting procedure on page 54 for correct choke and throttle settings during starting.

Fuel Filter The in-line fuel filter should be replaced by your dealer after every 100 hours of operation or annually. Do not attempt to clean the fuel filter.

Fuel Tank Cap This vehicle is equipped with a digi- tal fuel gauge that will indicate a low fuel condition. Refuel when the gauge indicates a low fuel condition. Always refuel with the engine stopped, and outdoors or in a well ventilated area. Refuel on a level surface. Remove the fuel tank cap to add fuel to the fuel tank. Use either leaded or unleaded gasoline with a minimum pump octane number of 87=(R+ M/ 2) octane. Do not use fuel with etha- nol content greater than 10 percent, such as E-85 fuel.

OFFON

Fuel Valve

Fuel Tank Cap

42

FEATURES AND CONTROLS Transmission Gear Selector The transmission gear selector is located on the right side of the vehicle. H: High Gear L: Low Gear N: Neutral R: Reverse P: Park To shift gears, brake to a com- plete stop. When the engine is idling, move the lever to the desired gear.

Shifting gears with the engine speed above idle or while the vehicle is moving can cause transmission damage.

Whenever the vehicle is left unattended, always place the transmission in PARK. The transmission is locked when its in PARK. Belt Life To extend belt life, use low forward gear when pulling a heavy load at less than 11 km/h for extended periods and when operating uphill at a slow speed.

Gear Selector

43

FEATURES AND CONTROLS Recoil Starter (if equipped) If the battery is too weak to start the engine, use the recoil starter. Follow the starting procedures on page 54, cranking the engine with the recoil starter instead of the main key switch. 1. Grasp the recoil starter rope

handle tightly. 2. Pull slightly until the starter

mechanism engages. 3. Pull the rope abruptly to start the engine.

Extending the recoil starter rope until it stops can cause damage to the recoil assembly. Do not extend the starter rope so far that it stops.

If the starter rope handle is not seated properly, water may enter the recoil housing and damage components. Make sure the handle is fully seated on the recoil housing, especially when traveling in wet areas.

Recoil Starter

Handle

44

FEATURES AND CONTROLS All Wheel Drive (AWD) System The AWD switch may be turned on or off while the vehicle is moving. AWD will not engage until engine speed is below 3100 RPM. AWD remains engaged until the switch is turned off. There is no limit to the length of time the vehicle may remain in AWD. If the switch is turned off while the demand drive unit is engaged, it will not disengage until the rear wheels regain traction. Engage AWD before getting into situations where maximum traction is needed. If the rear wheels are spinning, release the throttle before switching to AWD. Tip: The override switch allows activation of AWD in reverse if the AWD switch

is on. See page 34.

Switching to AWD while the rear wheels are spinning may cause severe drive shaft and gearcase damage. Always switch to AWD while the rear wheels have traction or are at rest.

AWD When the AWD switch is on, the vehicle is in four-wheel drive and the differential is locked, providing maximum traction. The demand drive unit automatically engages when the rear wheels lose trac- tion. When the rear wheels regain traction, the demand drive unit automatically disengages.

2X4 When the 2X4 switch is on, the vehicle is in two-wheel drive at all times and the dif- ferential is locked.

45

FEATURES AND CONTROLS Instrument Cluster Your vehicle is equipped with an instrument cluster that senses vehicle speed from the right front wheel. In addition to showing vehicle speed, the speedometer needle flashes when a warning condition exists. The instrument cluster measures distance in miles as well as hours of operation. It also includes a reverse speed limiter function that limits the vehicle's speed to approximately 11-14 km/h. Refer to page 34 for addi- tional information.

High water pressure may damage vehicle components. Wash the vehicle by hand or with a garden hose using mild soap.

Certain products, including insect repellents and chemicals, will damage the speedometer lens and other plastic surfaces. Do not use alcohol to clean the instrument cluster. Do not allow insect sprays to contact the lens. Immediately clean off any gasoline that splashes on the instrument cluster.

Rider Information

Center

Speedometer Needle Speedometer

46

FEATURES AND CONTROLS Instrument Cluster Rider Information Center The rider information center is located in the instrument cluster. All seg- ments will light up for 2.5 seconds at start-up. If the instrument cluster fails to illuminate, a battery over-voltage may have occurred and the instrument cluster may have shut off to protect the electronic speedome- ter. If this occurs, take the vehicle to your POLARIS dealer for proper diagnosis. 1. Gear Indicator - This

indicator displays gear shifter position: H = High Gear L = Low Gear N = Neutral R = Reverse Gear P = Park

2. AWD Indicator - This indicator illuminates when the AWD switch is in the AWD position.

3. Engine Hour Display Indicator 4. Service Interval/Diagnostic Mode Indicator 5. Odometer/Tachometer/Tripmeter/ Hour Meter 6. Fuel Gauge - The segments of the fuel gauge show the level of fuel

in the fuel tank. When the last segment clears, a low fuel warning is activated. All segments will flash, FUEL will display in the LCD, and the speedometer needle will blink. Refuel immediately.

7. Check Engine Warning Indicator - The word HOT displays if the engine overheats. Do not operate the vehicle if this warning appears. Serious engine damage could result.

8. Mode Indicator

1

2

3 4 5 6

8

7

47

FEATURES AND CONTROLS Instrument Cluster Rider Information Center Standard Modes Use the MODE button to toggle through the mode options. The reverse override button is also the MODE button. See page 34. NOTE: The transmission cannot be in reverse when using this feature.

Odometer Mode The odometer records the miles traveled by the vehicle. Trip Meter Mode The trip meter records the miles traveled by the vehicle on each trip if it's reset before each trip. To reset the trip meter, select the trip meter mode. Press and hold the mode button (override button) until the total changes to 0. NOTE: In the Rider Information Center, the trip meter display contains a deci-

mal point, but the odometer displays without a decimal point.

Hour Meter Mode This mode logs the total hours the engine has been in operation. Tachometer Mode The engine RPM is displayed digitally. NOTE: Small fluctuations in the RPM from day to day may be normal because

of changes in humidity, temperature and elevation.

48

FEATURES AND CONTROLS Instrument Cluster Rider Information Center Diagnostic Mode The wrench icon will display when the gauge is in the diagnostic mode. To exit the diagnostic mode, turn the key switch off and on. Any move- ment of the tires will also cause the gauge to exit the diagnostic mode. To enter the diagnostics mode: 1. Turn the key switch off and wait 10 seconds. 2. Lock the parking brake. 3. Place the transmission in neutral. 4. Hold the mode/reverse override button and turn the key switch on.

Release the switch as soon as the display is activated. 5. Use the mode button to toggle through the diagnostic screens.

49

FEATURES AND CONTROLS Instrument Cluster Rider Information Center Diagnostic Mode Battery Voltage Screen View this screen to check battery voltage level. Tachometer Screen View the tachometer to check engine speed. AWD Diagnostic Screen The gauge indicates whether or not current is flowing through the AWD coil (only on models with switchable AWD). This screen is for informa- tional purposes only. Please see your dealer for all major repairs. Gear Circuit Diagnostic Screen This screen displays the resistance value (in ohms) being read at the gear switch input of the gauge. This screen is for informational purposes only. Please see your dealer for all major repairs. Programmable service interval When the hours of engine operation equal the programmed service interval setting, the wrench icon will flash for 5 seconds each time the engine is started. When this feature is enabled, it provides a convenient reminder to perform routine maintenance. See page 50. The service interval is programmed at 50 hours at the factory.

50

FEATURES AND CONTROLS Instrument Cluster Rider Information Center Diagnostic Mode Programmable service interval To enable or disable the service interval: 1. Enter the diagnostic mode. 2. Toggle to the service interval screen. 3. Press and hold the mode button for about 7 seconds, until either ON

or OFF appears in the Rider Information Center, depending on your preference.

To reset the service interval: 1. Enter the diagnostic mode. 2. Toggle to the service interval screen. 3. Press and hold the mode button for 2-3 seconds, until the wrench

icon flashes. Release the button. 4. Press and release the mode button once to advance the setting by

one hour. Press and hold the mode button to advance the hours quickly.

5. If you scroll past the intended number, press and hold the button until the hours cycle back to zero.

6. When the desired setting is displayed, wait until the wrench icon stops flashing. The new service interval is now programmed.

Miles/Kilometers toggle The display in the tripmeter and odometer can be changed to display either standard or metric units of measurement. 1. Enter the diagnostic mode. 2. Toggle to the screen that displays either kilometers (KM) or miles

(MP). 3. Press and hold the mode button until the letters flash, then press and

release the button once. When the display stops flashing, the mode has been set.

51

OPERATION Fuel Safety

Gasoline is highly flammable and explosive under certain conditions.

Use extreme caution whenever handling gasoline.

Refuel with the engine stopped. Refuel outdoors or in a well-ventilated area.

Never fill a fuel container while it's on the vehicle. Static electricity between the rack and container could cause a spark.

Do not smoke or allow open flames or sparks in or near the area where refu- eling is performed or where gasoline is stored.

Do not overfill the tank. Do not fill the tank neck.

If gasoline spills on your skin or clothing, immediately wash it off with soap and water and change clothing.

Turn the fuel valve off whenever the vehicle is stored or parked.

WARNING

52

OPERATION Break-In Period The break-in period for your new POLARIS vehicle is the first ten hours of operation, or the time it takes to use the first two full tanks of gaso- line. No single action on your part will increase the life and performance of your vehicle more than following the procedures for a proper break- in. Careful treatment of a new engine and drive components will result in more efficient performance and longer life for these components. Do not operate at full throttle or high speeds for extended periods during the first three hours of use.

Engine and Drivetrain Break-in 1. Fill the fuel tank with the recommended fuel. See page 41. 2. Check the oil level. Add oil if necessary. 3. Select an open area that allows room to familiarize yourself with

vehicle operation and handling. 4. Drive slowly. Vary the throttle positions. Do not operate at sustained

idle. 5. Perform regular checks on fluid levels, controls and areas outlined

on the daily pre-ride inspection checklist. See page 53. 6. Pull only light loads. 7. Change the oil and filter at 20 hours or one month.

PVT Break-in (Clutches/Belt) Break in the clutches and belt by operating at slower speeds during the break-in period as recommended. Pull only light loads. Avoid aggres- sive acceleration and high speed operation during the break-in period.

53

OPERATION Pre-Ride Checklist

Item Remarks Page

Foot brake Ensure proper operation 38

Hand brake/lever travel Ensure proper operation 85

Brake fluid Ensure proper level 82

Front suspension Inspect, lubricate if necessary 68

Rear suspension Inspect, lubricate if necessary 68

Steering/steering lock Unlock the steering; ensure free oper- ation

40

Tires Inspect condition and pressure 90

Wheels/fasteners Inspect, ensure fastener tightness 90

Frame nuts, bolts, fasteners Inspect, ensure tightness -

Fuel and oil Ensure proper levels 41 70

Throttle Ensure proper operation 37 89

Indicator lights/switches Ensure proper operation 34

Engine stop switch Ensure proper operation 35

Mirrors Adjust for best side/rear vision 37

Air filter, pre-filter Inspect, clean 92

Air box sediment tube Drain deposits whenever visible -

Headlamp Check operation, apply POLARIS dielectric grease when lamp is replaced

95

Brake light/tail lamp Check operation, apply POLARIS dielectric grease when lamp is replaced

96

Riding gear Wear approved helmet, goggles, and protective clothing

16

Winch Inspect cable and switch. 57-58

54

OPERATION Starting the Engine

Engine exhaust contains poisonous carbon monoxide and can cause loss of consciousness resulting in severe injury or death. Never run an engine in an enclosed area.

1. Position the vehicle on a level surface.

2. Place the transmission in PARK. 3. Turn the fuel valve on. 4. Sit on the vehicle. Tip: The starter interlock will prevent the engine from starting if the transmission

is in gear and the brake is not engaged.

Tip: Do not use the choke if starting a warm engine. Excessive use of the choke can cause the spark plug to become wet fouled.

5. If the engine is cold, pull the choke knob out until it stops. If the knob doesn't stay where positioned, increase the tension by rotating the tension adjusting nut clockwise.

Tip: The variable choke is fully on when the knob is pulled completely out. The choke is off when the knob is pushed completely in. The choke can be adjusted gradually, depending on how much choke is needed for starting. Be sure the choke is off during operation, as excess fuel washing into the engine oil will increase wear on engine components.

6. Move the engine stop switch to RUN.

Tension Adjusting Nut

55

OPERATION Starting the Engine 7. Do not press the throttle while starting the

engine. Turn the ignition key past the POSITION LIGHTS ON position to engage the starter. Activate the starter for a maximum of five seconds, releasing the key when the engine starts.

8. If the engine does not start, release the starter and wait five seconds.

9. Repeat steps 7 and 8 until the engine starts.

Operating the vehicle immediately after starting could cause engine damage. Allow the engine to warm up for several minutes before operating.

10. If a warm engine has cooled to a point where it does not readily start, intermittent use of the choke (pulled half way out) may be necessary. If the engine is over-choked when warm, depress the throttle lever fully while cranking to aid in starting. Release the throttle lever immediately after the engine starts. If the engine does not start and all conditions are favorable, change the spark plug and try again.

11. If the engine slows or stops, position the choke knob half way in to allow proper engine warm up. Vary the engine RPM slightly with the throttle to aid in warm-up. When the engine idles smoothly, push the choke completely in.

Cold Weather Operation Internal engine condensation increases as outside temperatures decrease. If the vehicle is used year-round, check the oil level fre- quently. A rising oil level could indicate the accumulation of contami- nates such as water or excess fuel in the bottom of the crankcase. Water in the bottom of the crankcase can lead to engine damage and must be drained. Water accumulation increases as outside temperature decreases. See your POLARIS dealer for engine heater kits, which provide quicker warm-ups and easier starting in colder weather.

56

WINCH GUIDE The responsibility for safe operation of the winch ultimately rests with you, the operator. Read and understand all safety precautions and oper- ating instructions before operating the winch. Careless operation can result in serious injury. DO NOT use the winch to lift or move people.

Winch Safety Precautions 1. Be alert. Do not operate the winch under the influence of drugs,

alcohol or medication. 2. Practice using the winch so you are prepared to use it in an emer-

gency situation.

Never connect DC powered winches to AC current. Motor damage or fatal shock may occur.

Stand clear of the cable and load during winching. Keep helpers and spectators at a safe distance. If a cable pulls loose or breaks under the load, it can lash back with dangerous force.

3. Beware of the danger zone. The danger zone is the area of the rotating wire cable drum, the fairlead (if fitted), the cable, the hook and the motor. Before placing hands in or near the danger zone, first relieve tension on load, then disconnect the control switch.

4. If you are within four feet of the winch, do not hold the cable and the remote (if equipped) at the same time.

WARNING

DANGER

Danger Zone

57

WINCH GUIDE Winch Cable Care 1. The life of a cable is directly related to the care it receives. The wire

cable on a new winch (and any replacement cables) must be re- spooled under a minimum of a 100-lb. (45.4-kg) load before use. Failure to do this will result in cable damage.

2. Inspect all cable before use. Mashed, pinched, frayed or kinked areas severely reduce the load-carrying capability. Replace dam- aged cable promptly.

3. Prevent kinks before they occur. A. This is a start of a kink. Straighten

the cable before using it. B. The cable was pulled and the loop

has tightened to a kink. The cable is now permanently damaged and should not be used.

C. The result of kinking is that each strand pulls a different amount of load, causing the strands under the greatest tension to break. This reduces the load capacity of the entire cable.

4. Before re-spooling, remove all load from the cable. Hold the han- dlebar switch lead in one hand and the cable in the other. Move away from the vehicle as far as the switch will allow. Activate the switch, walk in several feet of cable, then release the switch. Repeat this process until the re-spooling is complete.

CAUTION! To avoid injury, always release the switch before your hand comes within four feet of the fairlead (the physical opening through which the cable passes).

5. Be sure the cable is distributed evenly and tightly on the drum. A loosely wound drum may allow the cable to work its way down into the layers of cable on the drum and become wedged.

6. Do not grease or oil the cable. Doing so causes dirt contamination that will reduce the life of the cable.

A

B

C

58

WINCH GUIDE Winch Preparation and Inspection

Wear heavy leather gloves whenever handling cable. Do not allow the cable to slip through your hands, even with gloves on. When handling the hook, always use a handsaver. Never place fingers into the hook. Placing fingers in the hook could result in injury.

Inspect the switch and wiring for cracks, pinched spots, frayed wire or loose connections. A damaged, shortened lead could cause the winch to operate as soon as it is plugged in.

Never touch the cable or hook while they are in tension or under load. Even at rest, the winch may have the cable in tension. Never guide a cable under tension onto the drum with your hand.

1. Winch with at least five wraps of cable around the winch drum. With fewer wraps, the cable could pull loose from the drum under load.

DANGER

WARNING

DANGER

59

WINCH GUIDE Winch Rigging

Take your time when rigging and use extra caution. Improper rigging can result in injury in addition to damage to the vehicle and equipment. Never handle the cable or rigging while another person is at the control switch.

1. Use a nylon sling to attach the cable to an anchor point.

CAUTION! Do not attach the hook back onto the cable. Doing so can cause the cable to break.

Always use a handsaver. Do not hold the hook with your hand. This is important not only when reeling cable in but also when removing cable from the winch under power.

2. Run the winch intermittently to take up cable slack. When using a pulley block, be sure the cable is running properly in all pulleys before apply- ing a load.

CAUTION! Never engage or disengage the clutch if the winch is under load, the cable is in tension or the drum is rotating.

WARNING

WARNING

60

WINCH GUIDE Winch Operation NOTICE: This winch is designed for intermittent use. Prolonged use may result

in damage due to overheating.

1. Use common sense. 2. Take your time. 3. Think through the situation. 4. Pay attention to what is going on when you are winching. 5. DO NOT overheat the winch motor. During extended winching,

stop and feel the winch motor. The motor should be cool enough to touch. If not, allow the motor to cool before continuing.

6. Extended winching will discharge your battery. If the low battery warning light comes on, stop winching. Make sure the transmission is in neutral or park, then rev the motor for a few minutes until the warning light goes out. Recharge the battery as soon as possible.

7. DO NOT overload or stall the winch. If the load is greater than the winch is capable of pulling, use a snatch block.

8. Avoid continuous side pulls. 9. Never tow the vehicle by the winch cable. 10. Never use the winch cable as a tie-down. 11. Use an anchor point that is stronger than what you are pulling. 12. DO NOT hook the cable back onto itself. This will damage the

cable.

61

WINCH GUIDE Winch Operation 13. Use as much cable as possible when pulling. Additional wraps of

cable on the spool will significantly reduce the pulling power of your winch. If the winch is still not capable of pulling the load, use a snatch block.

14. Never pull with less than five wraps of cable on the spool. 15. Inspect the condition of the cable prior to pulling. If the cable is

frayed or damaged, replace it as soon as possible. 16. DO NOT submerge the winch in water.

62

EMISSION CONTROL SYSTEMS Noise Emission Control System Do not modify the engine, intake or exhaust components, as doing so may affect compliance with governmental noise level requirements.

Spark Arrestor Your POLARIS vehicle has a spark arrestor that was designed for on- road and off-road operation. It is required that this spark arrestor remain installed and functional when the vehicle is operated.

Exhaust Emission Control System The emissions from the exhaust of this vehicle are controlled by engine design, including factory-set fuel delivery and ignition. The engine and related components must be maintained at POLARIS specifications to achieve optimal performance. Engine idle speed is the only adjustment POLARIS recommends that the operator perform. Any other adjustments should be performed by an authorized POLARIS dealer.

Electromagnetic Interference This spark ignition system complies with Canadian ICES-002. This vehicle complies with the EMC requirements of European direc- tives 97/24/EC and 2004/108/EC. Non-ionizing Radiation: This vehicle emits some electromagnetic energy. People with active or non-active implantable medical devices (such as heart monitoring or controlling devices) should review the lim- itations of their device and the applicable electromagnetic standards and directives that apply to this vehicle.

63

MAINTENANCE Periodic Maintenance Chart Maintenance intervals in the following chart are based upon average riding conditions. Vehicles subjected to severe use must be inspected and serviced more frequently. The programmable service interval mode on the instrument cluster will help determine when maintenance service is due. See page 45. Record maintenance and service in the Maintenance Log beginning on page 131. Service and adjustments are important for proper vehicle operation. If you're not familiar with safe service and adjustment procedures, have a qualified dealer perform these operations. Severe Use Definition Frequent immersion in mud, water or sand Racing or race-style high RPM use Prolonged low speed, heavy load operation Extended idle Short trip cold weather operation Pay special attention to the oil level. A rise in oil level during cold weather can indicate contaminants collecting in the oil sump or crank- case. Change oil immediately if the oil level begins to rise. Monitor the oil level, and if it continues to rise, discontinue use and determine the cause or see your dealer.

64

MAINTENANCE Periodic Maintenance Chart

Improperly performing the procedures marked with a could result in component failure and cause an accident, which may result in serious injury or death. Always have an authorized POLARIS dealer perform these services.

Maintenance Chart Key Perform these operations more often for vehicles subjected to

severe use. E Emission-related service (Failure to conduct this maintenance will

not void the emissions warranty but may affect emissions.) Have an authorized POLARIS dealer perform these services.

WARNING

65

MAINTENANCE Periodic Maintenance Chart Perform all services at whichever maintenance interval is reached first.

Perform these procedures more often for vehicles subjected to severe use. E Emission-Related Service Have an authorized POLARIS dealer perform these services.

Item Maintenance Interval (whichever comes first)

Remarks

Hours Calendar Kilometers

Steering - Pre-Ride - Make adjustments as need ed. See Pre-Ride Checklist on page 53.Front suspension - Pre-Ride -

Rear suspension - Pre-Ride -

Tires - Pre-Ride -

Brake fluid level - Pre-Ride -

Brake lever - Pre-Ride -

Foot brake - Pre-Ride

Brake system - Pre-Ride -

Wheels/fasteners - Pre-Ride -

Frame fasteners - Pre-Ride -

Engine oil level - Pre-Ride -

Winch - Pre-Ride - See pages 57-58.

E

Air filter, pre-filter - Daily - Inspect; clean often; replace as needed

Air box sediment tube

- Daily - Drain deposits when visible

Coolant - Daily - Check level daily, change coolant every 2 years

Headlight/taillight - Daily - Check operation; apply dielectric grease if replacing

E

Air filter, main element

- Weekly - Inspect; replace as needed

Recoil housing (if equipped)

- Weekly - Drain water as needed, check often if operating in wet conditions

Brake pad wear 10 Monthly 160 Inspect periodically

Battery 20 Monthly 300 Check terminals; clean; test

Demand drive fluid (front gearcase)

25 Monthly 400 Inspect level; change yearly

Rear gearcase oil (if equipped)

25 Monthly 400 Inspect level; change yearly

Transmission oil 25 Monthly 400 Inspect level; change yearly

E

Engine breather filter (if equipped)

25 Monthly 400 Inspect; clean if needed

66

MAINTENANCE Periodic Maintenance Chart

Item Maintenance Interval (whichever comes first)

Remarks

Hours Calendar Kilometers

Engine oil change (break-in)

- 1 M - Perform a break-in oil change at one month

General lubrication

50 3 M 800 Lubricate all fittings, pivots, cables, etc.

Shift linkage 50 6 M 800 Inspect, lubricate, adjust

Steering 50 6 M 800 Lubricate

Front suspension 50 6 M 800 Lubricate

Rear suspension 50 6 M 800 Lubricate

Carburetor float bowl

50 6 M 800 Drain bowl periodically and prior to storage

E

Throttle Cable/ ETC Switch

50 6 M 800 Inspect; adjust; lubricate; replace if necessary

E

Choke cable 50 6 M 800 Inspect; adjust; lubricate; replace if necessary

E Carburetor air intake ducts/flange

50 6 M 800 Inspect duct for proper seal- ing/air leaks

Drive belt 50 6 M 800 Inspect; adjust; replace as needed

Cooling system 50 6 M 800 Inspect coolant strength seasonally; pressure test system yearly

Engine oil change 100 6 M 1600 Perform a break-in oil change at one month

Oil filter change 100 6 M 1600 Replace with oil change

Oil tank vent hose (if equipped)

100 6 M 1600 Inspect routing, condition

E

Valve clearance 100 12 M 1600 Inspect; adjust

E

Fuel system 100 12 M 1600 Check for leaks at tank cap, lines, fuel valve, filter, pump, carburetor; replace lines every two years

E

Fuel filter 100 12 M 1600 Replace annually

Radiator 100 12 M 1600 Inspect; clean external surfaces

Cooling hoses 100 12 M 1600 Inspect for leaks

Engine mounts 100 12 M 1600 Inspect

Exhaust muffler/ pipe

100 12 M 1600 Inspect

67

MAINTENANCE Periodic Maintenance Chart

Perform these procedures more often for vehicles subjected to severe use. E Emission-Related Service Have an authorized POLARIS dealer perform these services.

Item Maintenance Interval (whichever comes first)

Remarks

Hours Calendar Kilometers

E

Spark plug 100 12 M 1600 Inspect; replace as needed

Wiring 100 12 M 1600 Inspect for wear, routing, security; apply dielectric grease to connectors subjected to water, mud, etc.

Clutches (drive and driven)

100 12 M 1600 Inspect; clean; replace worn parts

Front wheel bearings

100 12 M 1600 Inspect; replace as needed

Brake fluid 200 24 M 3200 Change every two years

Spark arrestor 300 36 M 4800 Clean out

Toe adjustment - Inspect periodically; adjust when parts are replaced

Brakes - Inspect daily; adjust as needed

Headlight aim - Adjust as needed

68

MAINTENANCE Lubrication Guide Always check and change fluids and lubricate greaseable compo- nents at the intervals outlined in the Periodic Maintenance Chart beginning on page 63. Items not listed in the chart should be lubri- cated at the General Lubrication interval.

Item Lube Method Engine Oil PS-4 PLUS Performance

Synthetic 2W-50 See page 69.

Brake Fluid DOT 4 Only See page 82.

Transmission Oil AGL PLUS Transmission Fluid

See page 75.

Front Demand Drive Unit (Front Gearcase)

Demand Drive Plus Fluid See page 77.

Front Prop Shaft Yoke POLARIS Premium U-Joint Lube

Grease fittings (3 pumps maxi- mum) every 800 km, before long periods of storage, or after pres- sure washing or submerging.

Front Prop Shaft Yoke

69

MAINTENANCE Engine Oil Oil Recommendations Always change the oil filter whenever changing oil. POLARIS recommends the use of POLARIS PS-4 PLUS Performance Synthetic 2W-50 4-cycle oil or a similar oil for this engine. Oil may need to be changed more frequently if POLARIS oil is not used. Always use 2W-50 oil. Follow the manufacturer's recommendations for ambient temperature operation. See page 122 for the part numbers of POLARIS products.

Mixing brands or using a non-recommended oil may cause serious engine damage. Always use a recommended oil. Never substitute or mix oil brands.

Oil Specifications

Model Lubricant Capacity Drain Plug Torque SPORTSMAN

Forest 500 PS-4 PLUS Performance Synthetic 2W-50 4-Cycle

Oil

1.9 liters 19-23 N-m

70

MAINTENANCE Engine Oil Oil Level 1. Position the vehicle on a level

surface. 2. Place the transmission in PARK.

3. Start the engine. Allow it to idle for 30 seconds.

4. Stop the engine.

5. Remove the dipstick. Wipe it dry with a clean cloth.

6. Reinstall the dipstick completely.

7. Remove the dipstick and check the oil level. Add oil as needed. Maintain the oil level in the safe range. Do not overfill.

8. Reinstall the dipstick.

Dipstick

SafeAdd Oil

Safe Range{

71

MAINTENANCE Engine Oil Oil Change

Hot oil may result in serious burns. Do not allow hot oil to contact skin.

1. Position the vehicle on a level surface.

2. Place the transmission in PARK.

3. Start the engine. Allow it to idle for two minutes.

4. Stop the engine.

5. Clean the area around the drain plug.

6. Place a drain pan under the oil tank.

7. Remove the drain plug.

8. Drain the oil.

9. Clean the drain plug. Reinstall the drain plug with a new sealing washer.

10. Torque to specification. See page 69.

Drain Plug

New Sealing Washer

Screen Fitting

72

MAINTENANCE Engine Oil Oil Change 11. Disconnect the lower oil deliv-

ery hose and remove the screen fitting from the oil tank. Clean the fitting. The fitting threads must be sealed with LOCTITE PST 505 or PTFE seal tape.

12. Reinstall the screen fitting and rotate the fitting clockwise a minimum of 2 1/2 turns into the tank threads. Continue to rotate the fitting until the nipple of the fitting aligns with the mark on the tank.

Tip: Do not over-tighten. Maximum torque for the screen fitting is 34 N-m.

13. Reattach the oil line.

14. Place towels under the oil filter. Using an oil filter wrench, turn the filter counter-clockwise to remove it.

15. Clean the filter sealing area on the crankcase.

16. Lubricate the filter o-ring. Check to make sure the o-ring is in good condition.

17. Install the new oil filter. After the filter contacts the crankcase surface, turn it 1/2 turn by hand.

18. Approximately 240 ml of engine oil will remain in the crankcase. To drain, remove the drain plug on the lower right side of the crank- case.

Tip: The sealing surfaces on the drain plug and crankcase should be clean and free of burrs, nicks or scratches.

19. Reinstall the drain plug. Torque to specification.

Alignment Mark

73

MAINTENANCE Engine Oil Oil Change 20. Remove the dipstick. 21. Add 1.9 liters of recommended oil. If the sump is not drained, add

about 1.6 liters initially. 22. Reinstall the dipstick.

23. Place the transmission in PARK. 24. Prime the oil pump using the procedure

on page 74. 25. Stop the engine. Check for oil leaks.

26. Check the oil level. Add oil as needed. Maintain the oil level in the safe range. Do not overfill.

27. Reinstall the dipstick. 28. Discard used oil and

filter properly.

SafeAdd Oil

Safe Range{

74

MAINTENANCE Engine Oil Oil Change Oil Pump Priming This priming procedure must be performed whenever the oil hose connection between the oil tank and pump inlet has been disconnected. 1. Clamp the vent line 5 cm from

the oil tank, between the end of the oil tank vent fitting and the vent line's pressure relief slit.

2. Start the engine. Allow it to idle for 10-20 seconds.

3. Remove the vent line clamp. If the line is bled properly, you should hear a rush of air. If you do not hear a rush of air, repeat the priming procedure.

Clamp

Pressure Relief Slit

Tank

5 cm

75

MAINTENANCE Transmission Oil Maintain the oil level at the bottom of the fill plug hole threads. Use the recommended oil. See page 122 for the part numbers of POLARIS products.

Oil Recommendations

Oil Level 1. Position the vehicle on a level

surface. 2. Place the transmission in PARK.

3. Remove the fill plug. 4. Check the oil level. Maintain the

level at the bottom of the fill hole threads.

5. Add the recommended oil as needed. Do not overfill.

6. Reinstall the fill plug. Torque to specification.

Lubricant Oil Change Capacity

Fill Plug Torque

Drain Plug Torque

AGL PLUS Transmission Fluid 948 ml 27-34 N-m 27-34 N-m

Fill Plug

Fill Level

76

MAINTENANCE Transmission Oil Oil Change 1. Position the vehicle on a level

surface. 2. Place the transmission in PARK.

3. Remove the fill plug. 4. Remove the drain plug. 5. Drain the oil into a drain pan. 6. Clean the drain plug. 7. Reinstall the drain plug. Torque

to specification. See page 75. 8. Add the recommended oil. 9. Reinstall the fill plug. Torque to

specification. 10. Check for leaks. 11. Discard used oil properly.

Drain Plug

77

MAINTENANCE Front Gearcase (Demand Drive) Fluid Fluid Recommendations

Use the recommended fluid. Use of other fluids may result in improper operation of components. See page 122 for the part numbers of POLARIS products. Maintain the fluid level at the bottom of the fill hole threads.

Fluid Level 1. Position the vehicle on a level

surface. 2. Place the transmission in PARK.

3. Remove the fill plug. 4. Add the recommended demand drive fluid as needed. 5. Reinstall the fill plug. Torque to specification.

Gearcase Lubricant Capacity Fill Plug Torque

Drain Plug Torque

Demand Drive Unit

Demand Drive Plus Fluid 265 ml 11-14 N-m 15 N-m

Drain Plug

Fill Plug

Fill Level

78

MAINTENANCE Front Gearcase (Demand Drive) Fluid Fluid Change 1. Position the vehicle on a level

surface. 2. Place the transmission in PARK.

3. Remove the fill plug. 4. Remove the drain plug.

Drain the fluid into a drain pan.

5. Clean the drain plug. 6. Reinstall the drain plug. Torque

to specification. See page 77. 7. Add the recommended fluid. 8. Reinstall the fill plug. Torque to

specification. 9. Check for leaks. 10. Discard used oil properly.

79

MAINTENANCE Carburetor This vehicle is calibrated at the factory for optimal performance at alti- tudes ranging from zero to 6,000 feet (1800 m) and temperatures of +40 degrees F. (4 degrees C.) or higher. Above 6000 feet (1800 m) the engine air/fuel mixture becomes overly rich and the engine loses approximately 3% of its power for each 1000-foot (304.8 m) increase in elevation. Although this power cannot be regained, adjustments to the carburetor and drive system can be made to allow more efficient opera- tion. Optional jets, available from your POLARIS dealer, are required for operation above 6,000 feet and temperatures below +40 degrees F. (4 degrees C.) Continuous operation of the engine without proper jetting when required can cause poor performance, overheating or PVT or engine damage. See your POLARIS dealer for more information about jetting the ATV for conditions in your area. Pilot screws are sealed with metal plugs and are serviceable only by POLARIS dealers.

Carburetor/Engine Idle RPM Adjustment Recommended engine idle RPM is 1200 +/- 200. If the engine idle speed is unsatisfactory and all other conditions are favorable, the carbu- retor can be adjusted. 1. Start the engine and allow it to

warm up for approximately five minutes.

2. Place the transmission in gear. 3. Lock the parking brake. 4. Turn the screw in (clockwise) to

raise RPM. Turn the screw out (counter-clockwise) to lower RPM.

Idle Screw

80

MAINTENANCE Cooling System Any time the cooling system has been drained for maintenance or repair, replace the coolant with a fresh mixture of antifreeze and water. Drain the cooling system every two years. Add fresh coolant. POLARIS recommends the use of POLARIS Premium 60/40 anti- freeze/coolant or a 50/50 mixture of high quality aluminum compatible anti-freeze/coolant and distilled water. POLARIS Premium 60/40 is pre- mixed and ready to use. Do not dilute with water. See page 122 for the part numbers of POLARIS products. Always follow the manufacturer's mixing recommendations for the freeze protection required in your area.

Recovery Bottle Coolant Some coolant level drop on new machines is normal, as the system is purging itself of trapped air. Add coolant as needed. Tip: Check the coolant level in the radi-

ator any time the recovery bottle has run dry.

1. Check the coolant level when the fluid is cool. Maintain the coolant level between the mini- mum and maximum marks on the bottle (when the fluid is cool).

2. Remove the left side panel. See page 88.

3. View the coolant level. 4. Add coolant as needed. 5. Reinstall the side panel.

Recovery Bottle

81

MAINTENANCE Cooling System Radiator Coolant

Escaping steam can cause severe burns. Never remove the pressure cap while the engine is warm or hot.

1. Remove the front box/rack. 2. Remove the radiator pressure

cap. 3. If coolant is not visible,

slowly add coolant through the radiator filler neck.

4. Reinstall the pressure cap. Tip: Use of a non-standard pressure

cap will not allow the recovery system to function properly. Con- tact your dealer for the correct replacement part.

5. Reinstall the front box/rack.

Radiator Cap

82

MAINTENANCE Brake Fluid Check brake fluid levels for both brake systems before each ride. Always maintain brake fluid at the recommended level. Do not overfill. The brakes should feel firm when they're applied. Spongy or weak brakes may indicate a fluid leak or low fluid level. A low fluid level may also mean that brake pads are worn and need to be replaced. Do not operate the vehicle with spongy or weak brakes. See your dealer for ser- vice.

Operating the vehicle with a spongy brake can result in loss of braking, which could cause an accident. Never operate the vehicle with spongy-feeling brakes.

If the fluid level is low add DOT 4 brake fluid only. See page 122 for the part numbers of POLARIS products.

An over-full master cylinder may cause brake drag or brake lock-up, which could result in serious injury or death. Maintain brake fluid at the recommended level. Do not overfill.

Under normal operation, the diaphragm extends into the reservoir as fluid level drops. If the fluid level is low and the diaphragm is not extended, a leak is likely and the diaphragm should be replaced. To ensure proper diaphragm operation, always fill the reservoir as needed whenever the cover is loosened or removed. Do not overfill.

Never store or use a partial bottle of brake fluid. Brake fluid is hygroscopic, meaning it rapidly absorbs moisture from the air. The moisture causes the boiling temperature of the brake fluid to drop, which can lead to early brake fade and the possibility of accident or severe injury. After opening a bottle of brake fluid, always discard any unused portion.

83

MAINTENANCE Brake Fluid Hand Brake The master cylinder is located on the left handlebar. Maintain the fluid level 6 mm below the top edge of the master cylinder. Do not overfill.

1. Position the vehicle on a level surface. Make sure the handlebars are straight.

2. View the fluid level through the indicator win- dow (eye) on the top of the master cylinder.

Tip: The eye will appear dark when the fluid level is full. When fluid is low, the eye will be clear.

3. Add the recommended fluid as needed. Do not overfill.

Master Cylinder

Indicator Window

Full

Low

84

MAINTENANCE Brake Fluid Foot Brake 1. Position the vehicle on a

level surface. 2. Remove the seat. 3. View the fluid level in the

master cylinder. 4. Maintain the fluid level

between the minimum and maximum marks. Do not overfill.

Foot Brake Fluid Reservoir

85

MAINTENANCE Brakes The front and rear brakes are hydraulic disc brakes, activated by apply- ing the foot brake. The handlebar brake is also hydraulic. Both brake systems are self-adjusting.

Brake Inspections Perform the following checks to keep the brake systems in good operat- ing condition. Check more often if brakes are used heavily under normal operation. 1. Always keep brake fluid at an adequate

level. See page 82. 2. Check the brake systems regularly for

fluid leaks. 3. Check the brakes for excessive travel or

spongy feel. 4. Check the friction pads for wear, damage

and looseness. Replace the pads when the friction material is worn to 1 mm.

5. Check the security and surface condition of the disc.

1 mm

86

MAINTENANCE Toe Alignment

Do not attempt to adjust tie rod alignment. All tie rod adjustments should be performed by an authorized POLARIS dealer.

Use the following procedure to check the toe alignment of the vehicle. The recommended toe alignment is 3-6 mm toe out. 1. Position the vehicle on a

level surface. 2. Place the handlebars in a

straight-ahead position. 3. Tie a length of string

between two stands as shown in the illustration. Position the stands so that the string is flush with the side of the rear tire. If available, you may use a long straight-edge instead of string.

4. Measure the distance from the string to the rim at the front (1) and rear (2) of the front rim. The rear measurement should be 2-3 mm more than the front measurement on each side of the vehicle to obtain the recommended 3-6 mm toe out alignment.

5. Repeat the measurement procedure on the other side of the vehicle. 6. If you discover improper alignment, see your POLARIS dealer for

service.

String

Stand

2

1

FRONT

87

MAINTENANCE Steering Assembly Check the steering assembly of the vehicle periodically for loose nuts and bolts. If loose nuts and bolts are found, see your POLARIS dealer for service before operating the vehicle.

Handlebar Adjustment The handlebars can be adjusted for rider preference.

Improper adjustment of the handlebars or incorrect torquing of the adjuster block tightening bolts can cause limited steering or loosening of the handlebars, resulting in loss of control. Follow the adjustment procedures exactly, or see your POLARIS dealer for service.

1. Remove the upper headlight pod.

2. Loosen the four handlebar bolts. 3. Adjust the handlebar to the

desired height. Tip: Be sure the handlebars do not con-

tact the gas tank or any other part of the machine when turned fully to the left or right.

4. Torque the front two bolts to 14-17 N-m, then torque the rear two bolts. A gap of up to 3 mm will remain at the rear bolts.

Rear Spring Adjustment The rear shock absorber spring is adjusted by rotating the adjuster either clockwise or counter-clockwise to increase or decrease spring tension.

14-17 N-m

Adjuster

88

MAINTENANCE Side Panel Removal 1. Remove the seat.

2. Grasp the rear of the side panel near the rear cab.

3. With a firm motion, pull the panel outward to disengage the side panel from the grommet.

4. Pull the panel downward and rearward to remove it.

Footwell Removal 1. Remove the four screws on

the bottom of the footwell. 2. Use a flat screwdriver or

sidecutters to remove the plastic rivets securing the footwell to the fenders.

3. Remove the footwell.

Screws

Rivets

89

MAINTENANCE Throttle Cable Freeplay Adjust throttle cable freeplay at the handlebar. 1. Locate the throttle cable adjuster

at the handlebar.

2. Squeeze the end of the rub- ber boot and slide it far enough to expose the end of the inline cable adjuster.

3. Loosen the adjuster lock nut.

4. Rotate the boot to turn the adjuster until 1.6-3.2 mm of freeplay is achieved at the thumb lever. Move the throt- tle lever back and forth while adjusting.

5. Tighten the lock nut. 6. Squeeze the end of the

rubber boot and slide it over the cable adjuster to its original position.

WARNING! Engine RPM should not increase when steering is turned full left or right. Readjust cable freeplay if this occurs.

Boot

Lock Nut Adjuster

1.6-3.2 mm

90

MAINTENANCE Tires

Operating your vehicle with worn tires, improperly inflated tires, non-standard tires or improperly installed tires will affect vehicle handling and could cause an accident.

Maintain proper tire pressure as described on the label on your vehicle and in the specifications section of the owner's manual.

Use only original equipment size and type when replacing tires.

Make sure the wheels are installed properly.

Replace tires when the tread depth measures 3 mm or less.

Refer to the specifications section beginning on page 120 for recom- mended tire type, size and pressure.

Tire Tread Depth Always replace tires when tread depth is worn to 3 mm or less.

Front Wheel Hub Tightening Front wheel bearing tightness and spindle nut retention are critical com- ponent operations. All service must be performed by your authorized POLARIS dealer.

Wheel Nut Torque Specifications Check the wheel nut torques occasionally and when they've been loos- ened for maintenance service.

Nut Type Nut Torque

Lug Nut (Aluminum Wheels) 41 N-m PLUS 1/4 TURN

2-Piece Flange Nut (Steel Wheels)

37 N-m

WARNING

3 mm

91

MAINTENANCE Tires Wheel Removal/Installation

Always use original equipment size and type when replacing tires. Install wheels properly.

1. Position the vehicle on a level surface.

2. Place the transmission in PARK.

3. Loosen the wheel nuts slightly.

4. Place a suitable stand under the footrest frame to raise the wheel slightly off the ground.

5. Remove the wheel nuts. 6. Remove the wheel.

7. Place the wheel on the hub. 8. Install the wheel nuts finger

tight. 9. Lower the vehicle to the

ground. 10. Torque the wheel nuts to

specification. See torque chart on page 90.

92

MAINTENANCE Air Filter Always clean and replace the air and breather filters at the intervals out- lined in the Periodic Maintenance Chart beginning on page 63. 1. Position the vehicle on a level

surface. 2. Place the transmission in PARK.

3. Remove the seat. 4. Release the air box

cover clips. 5. Remove the air

box cover.

6. Loosen the hose clamp.

7. Remove the filter. 8. Remove the pre-filter

from the filter.

9. Wash the pre-filter in soapy water. Rinse and air dry. 10. Replace the filter if needed. 11. Reverse the steps to reinstall all components.

Main Filter

Pre-Filter

93

MAINTENANCE Breather Filter/Hose The breather filter is on the hose between the engine and air box. 1. Remove the left side panel.

See page 88.

2. Remove the hose clamps from the filter and pull the filter out of the hoses.

3. Inspect the filter for debris. Blow gently through the filter in the direction of the arrow to check for clogging. Replace a damaged or clogged filter.

4. Check the hoses for cracks, deterioration, abrasion, or leaks. Replace as needed.

5. Reinstall the filter and hose clamps. Tip: The filter is effective with the arrow pointing in either direction.

Operation of your vehicle without a breather filter can cause engine damage.

Breather Filter

94

MAINTENANCE Lights Headlight Beam Adjustment The headlight beam can be adjusted slightly upward or downward. 1. Position the vehicle on a level

surface. The headlight should be approximately 7.6 m from a wall.

2. Place the transmission in PARK.

3. Measure the distance from the floor to the center of the headlight and make a mark on the wall at the same height. Include rider weight on the seat when measuring.

4. Start the engine.Turn the headlight switch to high beam. 5. Observe the headlight aim on the wall. The most intense part of the

headlight beam should be 5 cm below the mark on the wall. 6. Tighten or loosen the lower headlight screws to adjust the beam

upward or downward or to the left or right.

7.6 m

5 cm X X

95

MAINTENANCE Lights

Poor lighting can result in loss of control or an accident. Lights become dirty during normal operation. Wash the headlights and taillights frequently.

Hot components can cause serious burns to skin. Do not service the headlamps until they've cooled.

Headlight/Position Light Lamp Replacement When servicing a halogen lamp, do not touch the lamp with bare fingers. Oil from your skin leaves a residue, causing a hot spot that will shorten the life of the lamp. Hold the plastic part of the lamp.

1. Place the transmission in PARK. 2. Remove the front box/rack. 3. Remove the plug at the back of the

headlight. 4. Pull the harness plug to disconnect

it from the back of the headlight. 5. Position light: Rotate the socket to

remove it. Go to step 6. Headlamp: Reach under the bumper and remove the rubber cover from the back of the headlight. Turn the collar counter- clockwise and carefully remove the collar and socket.

6. Remove the lamp. Apply dielectric grease to the socket and install a new lamp.

7. Reverse all steps to reassemble the headlight.

Position Light

Collar

Socket

Headlamp

96

MAINTENANCE Lights Taillight Lamp Replacement 1. Place the transmission in

PARK. 2. Rotate the taillight socket

counter-clockwise to remove it. 3. Remove the lamp. 4. Apply dielectric grease to the

socket. 5. Install the new lamp. Test the lamp for proper operation. 6. Reinstall all components in reverse order.

Front Turn Signal Replacement If a front turn signal light becomes inoperable, the lamps cannot be replaced. Replace the entire signal lamp assembly.

Rear Turn Signal Lamp Replacement 1. Place the transmission in PARK. 2. Rotate the turn signal socket

counter-clockwise to remove it. 3. Remove the lamp. 4. Apply dielectric grease to the

socket. 5. Install the new lamp. Test the lamp for proper operation. 6. Reinstall all components in reverse order.

97

MAINTENANCE Fuse Replacement If the engine stops or will not start, or if you experience other electrical failures, a fuse may need replacement. Locate and correct any short circuits that may have caused the blown fuse, then replace the fuse. Spare fuses are provided in a compartment. 1. Remove the front box/rack. 2. Remove the suspect fuse from

the fuse panel. If the fuse is blown, install a new fuse with the same amperage.

3. Reinstall the front box/rack.

Fuse Panel

Fuses

5or6 15 20 20

98

MAINTENANCE Spark Plugs Spark Plug Recommendations Refer to the specifications section beginning on page 120 for the recom- mended spark plug type and gap for your vehicle. Torque spark plugs to specification.

Spark Plug Inspection Spark plug condition is indicative of engine operation. Check the spark plug firing end condition after the engine has been warmed up and the vehicle has been driven at higher speeds. Immediately check the spark plug for correct color. See page 99.

Normal Spark Plug The normal insulator tip is tan or brown. There will be few combustion deposits. The electrodes are not burned or eroded. This indicates the proper type and heat range for the engine and the service. The tip should not be white. A white insulator tip indicates overheating, caused by use of an improper spark plug or incorrect carburetor adjust- ments.

Wet Fouled Spark Plug The wet fouled insulator tip is black. A damp oil film covers the firing end. There may be a carbon layer over the entire nose. Generally, the electrodes are not worn. General causes of fouling are excessive oil, use of non-recommended oil, improper use of the choke, or incorrect carbu- retor adjustments.

Plug Condition Torque Specification

New Spark Plug 12-15 N-m

Previously Installed Spark Plug 23-27 N-m

99

MAINTENANCE Spark Plugs Spark Plug Removal 1. Remove the left side panel.

See page 88.

2. Remove the spark plug cap. 3. Use the spark plug wrench

to remove the spark plug. Turn the plug counter- clockwise to remove it.

4. Inspect the electrodes for wear and carbon buildup. Replace worn or fouled plugs. Verify that the gap is at specification before installation.

5. Reinstall the spark plug. Torque to specification. See page 98.

6. Reinstall the spark plug cap.

100

MAINTENANCE Vehicle Immersion If your vehicle has been totally submerged in water and it's impossible to have it serviced before further operation, perform the following pro- cedure.

If the vehicle stops while fully submerged, major engine damage can result if the machine is not thoroughly inspected. Take the vehicle to your dealer before starting the engine.

1. Move the vehicle out of the water.

2. Turn the fuel valve off.

3. Drain any water found in the air box.

4. Remove the spark plug.

5. Loosen the carburetor drain screw and drain the carburetor.

6. Turn the engine over several times using the electric start.

Drain Screw

101

MAINTENANCE Vehicle Immersion 7. Dry the spark plug. Reinstall the

plug or install a new plug. Torque to specification. See page 98.

8. Tighten the carburetor drain screw.

9. Turn the fuel valve on.

10. Attempt to start the engine. If necessary, repeat the drying procedure.

11. Have the vehicle serviced by your dealer promptly, whether you succeed in starting it or not.

12. If water has been ingested into the PVT, follow the procedure on page 105 for drying out the PVT.

102

MAINTENANCE Spark Arrestor Occasionally, the spark arrestor may accumulate carbon, which can restrict the exhaust if left unattended. Purge the spark arrestor.

Allow components to cool sufficiently before servicing. The exhaust system can get extremely hot. Never run the engine in an enclosed area or indoors. Exhaust contains poisonous carbon monoxide gas. Never go under the vehicle while it's inclined.

Remove any combustible materials from the area. Wear eye protection and leather work gloves. Do not stand behind or in front of the vehicle while purging.

1. Position the vehicle on a level surface.

2. Place the transmission in PARK.

3. Remove the arrestor clean-out plug from the bottom of the muffler.

4. Start the engine. 5. Quickly squeeze and

release the throttle lever several times to purge car- bon from the system.

103

MAINTENANCE Spark Arrestor 6. If carbon comes out of the

exhaust, cover or plug the exhaust outlet. Wear protective gloves.

7. Lightly tap on the exhaust pipe with a rubber mallet while repeat- ing step 5.

8. If particles are still suspected to be in the muffler, elevate the rear of the vehicle 30 cm higher than the front. Block the wheels.

9. Place the transmission in PARK. Repeat steps 5 to 7 until no more particles are expelled.

10. Stop the engine. Allow the arrestor to cool. 11. Reinstall the arrestor plug and remove the exhaust outlet cover or

plug.

30 cm

104

MAINTENANCE PVT System

Do not modify any component of the PVT system. Doing so may reduce its strength so that a failure may occur at a high speed. The PVT system has been precision balanced. Any modification will cause the system to be out of balance, creating vibration and additional loads on components.

The PVT system rotates at high speeds, creating large amounts of force on clutch components. Extensive engineering and testing has been conducted to ensure the safety of this product. However, as the owner, you have the following responsibilities to make sure this system remains safe:

Always follow all recommended maintenance procedures. See your dealer as outlined in the owner's manual.

This PVT system is intended for use on POLARIS products only. Do not install it in any other product.

Always make sure the PVT housing is securely in place during operation.

105

MAINTENANCE PVT System When To Use Low Range and High Range

PVT Drying There may be some instances when water is accidently ingested into the PVT system. Dry it out before operating. 1. Position the vehicle on a level

surface. 2. Place the transmission in PARK.

3. Remove the drain plug. Allow the water to drain completely. Reinstall the drain plug.

4. Start the engine. 5. Apply varying throttle for 10-15 seconds to expel the moisture and

air-dry the belt and clutches. Do not hold the throttle wide open for more than 10 seconds.

6. Allow the engine RPM to settle to idle speed, then shift the trans- mission to the lowest available range.

7. Test for belt slippage. If the belt slips, repeat the process. 8. Take the vehicle to your dealer for service as soon as possible.

Condition Range to Use

Operating at speeds less than 11 km/h Low

Towing heavy loads Low

Operating in rough terrain (swamps, mountains, etc.) Low

Operating at speeds greater than 11 km/h High

106

MAINTENANCE Recoil Housing (if equipped) Always drain the recoil housing after operating the vehicle in wet conditions. Drain the housing before storing the vehicle. Make sure the housing is completely dry before reinstalling the drain plug.

1. Place the transmission in PARK. 2. Stop the engine.

3. Remove the drain screw on the bottom of the recoil housing.

4. Allow the housing to drain com- pletely.

5. Reinstall the drain screw. Tip: Do not open the crankcase drain

unless the engine has ingested water. On 4-cycle engines, some engine oil will be lost if the crankcase drain is opened.

Recoil Housing

107

MAINTENANCE Battery

Improperly connecting or disconnecting battery cables can result in an explosion and cause serious injury or death. When removing the battery, always disconnect the negative (black) cable first. When reinstalling the battery, always connect the negative (black) cable last.

Battery electrolyte is poisonous. It contains sulfuric acid. Serious burns can result from contact with skin, eyes or clothing. Antidote: External: Flush with water. Internal: Drink large quantities of water or milk. Follow with milk of magnesia, beaten egg, or vegetable oil. Call physician immediately. Eyes: Flush with water for 15 minutes and get prompt medical attention.

Batteries produce explosive gases. Keep sparks, flame, cigarettes, etc. away. Ventilate when charging or using in an enclosed space. Always shield eyes when working near batteries. KEEP OUT OF REACH OF CHILDREN.

Your vehicle may have either a sealed battery, which requires little maintenance, or a conventional battery. A sealed battery can be identi- fied by its flat covers on the top of the battery. A conventional battery has six filler caps on the top of the battery. Always keep battery terminals and connections free of corrosion. If cleaning is necessary, remove corrosion with a stiff wire brush. Wash with a solution of one tablespoon baking soda and one cup water. Rinse well with tap water and dry off with clean shop towels. Coat the termi- nals with dielectric grease or petroleum jelly. Be careful not to allow cleaning solution or tap water into a conventional battery.

WARNING

WARNING

108

MAINTENANCE Battery Battery Removal 1. Place the transmission in PARK. 2. Remove the seat. 3. Disconnect the battery hold-down strap. 4. Remove the battery cover (if equipped). 5. On conventional batteries, remove the battery vent tube. 6. Disconnect the black (negative) battery cable first. 7. Disconnect the red (positive) battery cable last. 8. Lift the battery out of the vehicle. Be careful not to tip a conven-

tional battery sideways, which could spill electrolyte. NOTICE: If electrolyte spills, immediately wash it off with a solution of one

tablespoon baking soda and one cup water to prevent damage to the vehicle.

109

MAINTENANCE Battery Battery Installation 1. Ensure that the battery is fully charged. 2. Place the battery in the battery holder. 3. With conventional batteries, install the battery vent tube (sealed bat-

teries do not have a vent tube). The vent tube must be free of obstructions and securely installed. Route the tube away from the frame and vehicle body to prevent contact with electrolyte.

Battery gases could accumulate in an improperly installed vent tube and cause an explosion, resulting in serious injury or death. Always ensure that the vent tube is free of obstructions and is securely installed as recommended.

4. On conventional batteries, coat the terminals with dielectric grease or petroleum jelly.

5. Connect and tighten the red (positive) cable first. 6. Connect and tighten the black (negative) cable last. 7. Secure the battery hold-down strap. 8. Reinstall the battery cover (if equipped). 9. Verify that cables are properly routed. Cables should be safely

tucked away at the front and rear of the battery. 10. Reinstall the seat.

110

MAINTENANCE Battery Battery Storage Whenever the vehicle is not used for a period of three months or more, remove the battery from the vehicle, ensure that it's fully charged, and store it out of the sun in a cool, dry place. Check battery voltage each month during storage and recharge as needed to maintain a full charge. Battery charge can be maintained by using a POLARIS Battery Tender charger or by charging about once a month to make up for normal self- discharge. Battery Tender can be left connected during the storage period, and will automatically charge the battery if the voltage drops below a pre-determined point. See page 122 for the part numbers of POLARIS products.

Battery Fluid (Conventional Battery) Check the battery fluid level often. Maintain the fluid level between the upper and lower level marks. Add only distilled water. Tap water contains minerals that are harmful to a battery.

Lower Mark

Upper Mark

111

MAINTENANCE Battery Battery Charging (Conventional Battery) 1. Remove the battery from the vehicle to prevent damage from leak-

ing or spilled electrolyte during charging. See page 108. 2. Charge the battery with a charging output no larger than 1/10 of the

batterys amp/hr rating. Charge as needed to raise the specific grav- ity to 1.270 or greater.

3. Reinstall the battery. See page 109. Make sure the positive terminal is toward the front of the vehicle.

Battery Charging (Sealed Battery) The following battery charging instructions apply only to the installa- tion of a sealed battery. Read all instructions before proceeding with the installation of this battery. The sealed battery is already filled with electrolyte and has been sealed and fully charged at the factory. Never pry the sealing strip off or add any other fluid to this battery. The single most important thing about maintaining a sealed battery is to keep it fully charged. Since the battery is sealed and the sealing strip cannot be removed, you must use a voltmeter or multimeter to measure DC voltage.

112

MAINTENANCE Battery Battery Charging (Sealed Battery) For a refresh charge, follow all instructions carefully. 1. Check the battery voltage with a voltmeter or multimeter. A fully

charged battery will register 12.8 V or higher. 2. If the voltage is less than 12.8 volts, recharge the battery at 1.2 amps

or less until battery voltage is 12.8 or greater. 3. When using an automatic charger, refer to the charger manufac-

turer's instructions for recharging. When using a constant current charger, use the following guidelines for recharging.

An overheated battery may explode, causing severe injury or death. Always watch charging times carefully. Stop charging if the battery becomes very warm to the touch. Allow it to cool before resuming charging.

Always verify battery condition before and 1-2 hours after the end of charging.

State of Charge

Voltage Action Charge Time

(Using constant current charger @ standard amps specified on top of battery)

100% 12.8-13.0 volts None, check at 3 mos. from date of

manufacture

None required

75%-100% 12.5-12.8 volts May need slight charge, if no charge given,

check in 3 months

3-6 hours

50%-75% 12.0-12.5 volts Needs charge 5-11 hours

25%-50% 11.5-12.0 volts Needs charge At least 13 hours, verify state of charge

0%-25% 11.5 volts or less Needs charge with desulfating charger

At least 20 hours

113

MAINTENANCE Cleaning and Storage Washing the Vehicle Keeping your POLARIS vehicle clean will not only improve its appear- ance but it can also extend the life of various components. High water pressure may damage components. POLARIS recommends washing the vehicle by hand or with a garden hose, using mild soap. Certain products, including insect repellents and chemicals, will damage plastic surfaces. Do not allow these types of products to contact the vehicle. 1. Use a professional-type washing cloth, cleaning the upper body first

and the lower parts last. 2. Rinse with clean water frequently. 3. Dry surfaces with a chamois to prevent water spots.

Washing Tips Avoid the use of harsh cleaners, which can scratch the finish. Do not use a power washer to clean the vehicle. Do not use medium to heavy duty compounds on the finish. Always use clean cloths and pads for cleaning and polishing. Old or

reused cloths and pads may contain dirt particles that will scratch the finish.

114

MAINTENANCE Cleaning and Storage Washing the Vehicle If a high pressure water system is used for cleaning (not recommended), exercise extreme caution. The water may damage components and could remove paint and labels. Avoid directing the water stream at the follow- ing items: Wheel bearings Radiator Transmission seals Brakes Cab and body panels Electrical components Switches and controls Labels and decals If an informational or graphic label becomes illegible or comes off, con- tact your POLARIS dealer to purchase a replacement. Replacement safety labels are provided by POLARIS at no charge. Grease all zerk fittings immediately after washing. Allow the engine to run for a while to evaporate any water that may have entered the engine or exhaust system.

Polishing the Vehicle POLARIS recommends the use of common household aerosol furniture polish for polishing the finish on your POLARIS vehicle. Follow the instructions on the container. Polishing Tips Avoid the use of automotive products, some of which can scratch the

finish of your vehicle. Always use clean cloths and pads for cleaning and polishing. Old or

reused cloths and pads may contain dirt particles that will scratch the finish.

115

MAINTENANCE Cleaning and Storage Chrome Wheel Care (if equipped) Proper maintenance will protect chrome wheels from corrosion, pre- serve wheel life and ensure a "like new" appearance for many years. Chrome wheels exposed to road salt (or salt in the air in coastal areas) are more susceptible to corrosion if not properly cleaned. Clean chrome wheels more often if they're exposed to salt or other corrosive elements. 1. Wash chrome wheels frequently. Use a mild detergent. Never use

abrasive cleaners on plated or painted surfaces. 2. Rinse well with clear water. Soap, detergents, salt, dirt, mud and

other elements can cause corrosion. 3. Polish the clean chrome wheels periodically. Use an automotive

grade chrome polish. 4. Routinely and liberally apply a weather resistant wax to each pol-

ished chrome wheel. Choose a product suitable for chrome finishes. Read and follow the product labels and instructions.

Removing Corrosion If light rust is found on the chrome finish, use steel wool (#0000-OTT grade) to remove it. Gently rub the affected areas with the steel wool until the corrosion has been removed. Clean and polish the wheel as out- lined above.

116

MAINTENANCE Cleaning and Storage Storage Tips

Starting the engine during the storage period will disturb the protective film created by fogging and damage could occur. Never start the engine during the storage period.

Clean the Exterior Make any necessary repairs and clean the vehicle as recommended. See page 113.

Stabilize the Fuel 1. Fill the fuel tank. 2. Add POLARIS Carbon Clean Fuel Treatment or POLARIS Fuel

Stabilizer. Follow the instructions on the container for the recom- mended amount. Carbon Clean removes water from fuel systems, stabilizes fuel and removes carbon deposits from pistons, rings, valves and exhaust systems.

3. Allow the engine to run for 15-20 minutes to allow the stabilizer to disperse through the fuel tank and carburetor.

4. Turn the fuel valve off. 5. Drain the carburetor bowl.

Oil and Filter Change the oil and filter. See page 71.

Air Filter / Air Box 1. Inspect and clean (or replace) the pre-cleaner and air filter. 2. Clean the air box. 3. Clean or replace the breather filter. 4. Drain the sediment tube.

Recoil Housing (if equipped) 1. Drain the recoil housing. See page 106.

117

MAINTENANCE Cleaning and Storage Storage Tips Fluid Levels Inspect the fluid levels. Change fluids as recommended in the Periodic Maintenance Chart beginning on page 63. Demand drive unit (front gearcase) Transmission Rear gearcase (if equipped) Brake fluid (change every two years and any time the fluid looks dark

or contaminated) Coolant (test strength/fill)

Fog the Engine 1. Treat the fuel system with POLARIS Carbon Clean. See page 116. 2. Remove the spark plug. Pour 30-45 ml of engine oil into the plug

holes. 3. Reinstall the spark plugs. Torque to specification. 4. Apply dielectric grease to the inside of each spark plug cap. Rein-

stall the caps. 5. Turn the engine over several times (using the recoil starter, if

equipped). Oil will be forced in and around the piston rings and ring lands, coating the cylinder with a protective film of fresh oil.

6. If POLARIS fuel system additive is not used, the fuel tank, fuel lines, and carburetor should be completely drained of gasoline.

7. To eliminate any fuel remaining in the carburetor, run the engine until it stops.

118

MAINTENANCE Cleaning and Storage Storage Tips Inspect and Lubricate Inspect all cables and lubricate all areas of the vehicle as recommended in the Periodic Maintenance Chart beginning on page 63.

Battery Storage See pages 110-111 for storage and charging procedures.

Storage Area/Covers 1. Set the tire pressure and safely support the vehicle with the tires

slightly off the ground. 2. Be sure the storage area is well ventilated. 3. Cover the vehicle with a genuine POLARIS cover. Do not use plas-

tic or coated materials. They do not allow enough ventilation to pre- vent condensation, and may promote corrosion and oxidation.

Accessories Auxiliary power outlets provide 12-volt power for operating accesso- ries. Accessory outlets are available for all models. POLARIS also has a wide range of additional accessories available for your vehicle. Always install accessories that are approved for use on this vehicle. Please see your POLARIS dealer.

119

MAINTENANCE Transporting the Vehicle Follow these procedures when transporting the vehicle. 1. Stop the engine. 2. Place the transmission in PARK. 3. Secure the fuel cap, oil cap and

seat.

4. Remove the key to prevent loss during transporting.

5. Always tie the frame of the POLARIS vehicle to the transporting unit securely with suitable straps or rope. Do not attach tie straps to the front A-arm bolt pockets.

Towing a Disabled Vehicle If towing the vehicle is necessary, shift the transmission into neutral for better mobility and to prevent damage to the belt. Always attach the tow rope to the frame of the POLARIS vehicle.

120

SPECIFICATIONS

* Based on EU Directive 76/432/EC

SPORTSMAN Forest 500 Maximum Weight Load Capacity 485 lbs. (220 kg) (operator, cargo, accessories) Dry Weight 325 Kg +/- 7 % , based on configuration Fuel Capacity 4.25 gal. (16 l) Engine Oil Capacity 2 qts. (1.9 l) Coolant Capacity 2.7 qts. (2.5 l) Demand Drive Fluid Capacity 9 oz. (265 ml) Transmission Oil Capacity 32 oz. (948 ml) Front Rack/Storage Box Capacity 90 lbs. (41 kg) Rear Rack/Storage Box Capacity 180 lbs. (81.6 kg) Unbraked Trailer Towing Capacity*

1786 lbs. (810 kg)

Overall Length 83 in. (211 cm) Overall Width 48 in. (122 cm) Overall Height 48 in. (122 cm) Wheelbase 50.5 in. (128.3 cm) Ground Clearance 11 in. (28 cm) Minimum Turning Radius 65 in. (165 cm) unloaded Engine EH500PLE (Low Torque Capacity) Displacement 498 cc Engine Power 27 kW Bore x Stroke 92 x 75 Alternator Output 260 w Compression Ratio 10.2:1 Fuel System 40 mm Mikuni carburetor Pilot Jet 40 Main Jet 155 Needle Jet X-6M Jet Needle 6MGHI 194 Pilot Screw By flow (taper 12.5) (Brass Plug) Ignition System Digital CDI Ignition Timing 30 +/- 2 @ 5000 RPM Spark Plug / Gap NGK BKR6E / .035 in. (0.9 mm) Lubrication System Dry Sump Seat Single Seat, length 650 mm Steering System Akerman Principle, with handlebar controls Transmission Power System Shaft drive on all wheels

121

SPECIFICATIONS

Jetting Chart

Clutching

SPORTSMAN Forest 500 Transmission and Gears High/Low/Neutral/Reverse/Parking Driving System Type Automatic PVT (POLARIS Variable Transmis-

sion) Front Suspension MacPherson strut with 8.2" (21 cm) travel Rear Suspension Progressive rate with 9.5" (24 cm) travel Gear Reduction, Low 23.91:1 Gear Reduction, Reverse 21.74:1 Gear Reduction, Forward 10.57:1 Drive Ratio, Front 3.82:1 Tires Type Front Off Road Style, Deep Tread Design, size 26x8-14

/ 7 psi Pressure Tires Type Rear Off Road Style, Deep Tread Design, size 26x10-

14 / 5 psi Pressure Brakes, Front/Rear Single-Control handlebar hydraulic disc on all

wheels Brakes, Auxiliary Foot-Activated Hydraulic Disc on all wheels Parking Brake Hydraulic lock, all wheel, Mechanical on Gear-

box Hitch Rear mount for attachment of coupling devices Winch Front permanent Installed winch with 2500 Lbs,

1,125 Kg Capacity Headlight 2 dual beam on bumper (55/60 watt) Taillights 8.26 watts Brake Light 26.9 watts Instrument Cluster LCD

ALTITUDE Meters (Feet)

AMBIENT TEMPERATURE Below 40 F (Below 5 C)

+40F and above (+5C and above)

0-1800 (0-6000) 160 155

1800-3700 (6000-12000)

152.5 147.5

Altitude Shift Weight

Drive Clutch Spring

Driven Clutch Spring

Helix/Spring Setting

Meters (Feet)

0-1800 (0-6000)

10 WHF PN 5632283

Blue/Green PN 7041157

Black PN 7041782

41-37 PN 5132344

2+2

1800-3700 (6000-12000)

10 RH PN 5630709

Blue/Green PN 7041157

Black PN 7041782

41-37 PN 5132344

2+2

122

POLARIS PRODUCTS Part Number

Description

Engine Lubricant

2870791 Fogging Oil (12 oz. Aerosol)

2876244 PS-4 PLUS Performance Synthetic 2W-50 4-Cycle Oil (.95 l)

2876245 PS-4 PLUS Performance Synthetic 2W-50 4-Cycle Oil(3.8 l)

Gearcase / Transmission Lubricants

2878068 AGL PLUS Transmission Fluid (.95 l)

2878069 AGL PLUS Transmission Fluid (3.8 l)

2877922 Demand Drive Plus Fluid (.95 l)

2877923 Demand Drive Plus Fluid (3.8 l)

2870465 Pump for 3.8 liter jug

2871654 Premium Demand Drive Hub Fluid (237 ml)

2872277 Premium Demand Drive Hub Fluid (9.5 l)

Coolant

2871323 60/40 Coolant (3.8 l)

2871534 60/40 Coolant (.95 l)

Grease / Specialized Lubricants

2871312 Grease Gun Kit, Premium All Season

2871322 Premium All Season Grease (89 ml cartridge)

2871423 Premium All Season Grease (414 ml cartridge)

2871460 Starter Drive Grease

2871515 Premium U-Joint Lube (89 ml)

2871551 Premium U-Joint Lube (414 ml)

2871329 Dielectric Grease (NyogelTM)

Additives / Miscellaneous

2871326 Carbon Clean Plus

2870652 Fuel Stabilizer

2872189 DOT 4 Brake Fluid

2872893 Engine Degreaser

2871956 LoctiteTM 565 Thread Sealant

2871076 POLARIS Battery TenderTM Charger

123

TROUBLESHOOTING Drive Belt Wear/Burn

Possible Cause Solution

Driving onto a pickup or tall trailer in high range

Use low range.

Starting out going up a steep incline

Use low range or turn around using the K-turn (see page 26).

Driving at low RPM or speed (5-11 km/h)

Drive at a higher speed or use low range more frequently.

Insufficient warm-up at low ambient tempera- tures

Warm the engine at least 5 minutes. With the transmission in neutral, advance the throttle to about 1/8 throttle in short bursts, 5 to 7 times. The belt will become more flex- ible and prevent belt burning.

Slow/easy clutch engage- ment

Use the throttle quickly and effectively.

Towing/pushing at low RPM/low ground speed

Use low range only.

Utility use/plowing Use low range only.

Stuck in mud or snow Shift the transmission to low range. Carefully use fast, aggressive throttle application to engage clutch. WARNING: Excessive throttle may cause loss of control and vehicle overturn.

Climbing over large objects from a stopped position

Belt slippage from water or snow ingestion into the PVT system

Dry out the PVT. See page 105. Inspect clutch seals for damage if repeated leaking occurs.

Clutch malfunction See your POLARIS dealer.

Poor engine performance Check for fouled plugs or foreign material in gas tank or fuel lines. See your dealer.

Slippage from failure to warm up belt

Always warm up the belt by operating below 48 km/h for 1.6 km. Operate 8 km or more when temperature is below freezing.

Wrong or missing belt Install the recommended belt.

Improper break-in Always break in a new belt and/or clutch. See page 52.

124

TROUBLESHOOTING Engine Does Not Rotate

Engine Rotates, Fails to Start

Engine Backfires

Possible Cause Solution

Tripped circuit breaker Reset the breaker

Low battery voltage Recharge the battery to 12.8 VDC

Loose battery connections Check all connections and tighten

Loose solenoid connections Check all connections and tighten

Possible Cause Solution

Out of fuel Refuel

Clogged fuel valve or filter Replace the filter

Water is present in fuel Drain the fuel system and refuel

Old or non-recommended fuel Replace with fresh recommended fuel

Fuel valve is turned off Turn the fuel valve on

Fouled or defective spark plug(s) Inspect plugs and replace if necessary

No spark to spark plug Inspect plugs, verify stop switch is on

Water or fuel in crankcase Immediately see your POLARIS dealer

Low battery voltage Recharge the battery to 12.8 VDC

Mechanical failure See your dealer

Possible Cause Solution

Weak spark from spark plug Inspect, clean and/or replace spark plugs

Incorrect spark plug gap or heat range Set gap to specs or replace plugs

Old or non-recommended fuel

Loose ignition connections Check all connections and tighten

Water present in fuel Replace with fresh recommended fuel

Incorrectly installed spark plug wires See your dealer

Incorrect ignition timing See your dealer

Mechanical failure See your dealer

125

TROUBLESHOOTING Engine Pings or Knocks

Engine Runs Irregularly, Stalls or Misfires

Possible Cause Solution

Poor quality or low octane fuel Replace with recommended fuel

Incorrect ignition timing See your dealer

Incorrect spark plug gap or heat range Set gap to specs or replace plugs

Possible Cause Solution

Fouled or defective spark plug(s) Inspect, clean and/or replace spark plug(s)

Worn or defective spark plug wires See your dealer

Incorrect spark plug gap or heat range Set gap to specs or replace plugs

Loose ignition connections Check all connections and tighten

Water present in fuel Replace with new fuel

Low battery voltage Recharge battery to 12.8 VDC

Kinked or plugged fuel tank vent line Inspect and replace

Incorrect fuel Replace with recommended fuel

Clogged air filter Inspect and clean or replace

Reverse speed limiter malfunction See your dealer

Electronic throttle control malfunction See your dealer

Other mechanical failure See your dealer

Possible Lean Fuel Cause Solution

Low or contaminated fuel Add or change fuel, clean the fuel system

Low octane fuel Replace with recommended fuel

Clogged fuel filter Replace filter

Kinked or plugged fuel vent line Inspect and replace (if equipped)

Incorrect fuel Replace with recommended fuel

Incorrect jetting See your POLARIS dealer

Possible Rich Fuel Cause Solution

Fuel is very high octane Replace with lower octane fuel

Overuse of choke Inspect, clean and/or replace spark plugs

Stopping/starting without adequate warm-up

Allow engine to warm up before operat- ing and/or stopping

Incorrect fuel Replace with recommended fuel

Clogged air filter Inspect and clean or replace

Incorrect jetting See your POLARIS dealer

126

TROUBLESHOOTING Engine Stops or Loses Power

Engine Overheating

Possible Cause Solution

Out of fuel Refuel, cycle key to ON position three times for 5 seconds each, then start

Kinked or plugged fuel vent line Inspect and replace (if equipped)

Overuse of choke Inspect, clean and/or replace spark plugs

Water is present in fuel Replace with fresh recommended fuel

Old or non-recommended fuel Replace with fresh recommended fuel

Fouled or defective spark plug(s) Inspect, clean and/or replace spark plug(s)

Worn or defective spark plug wires See your dealer

Incorrect spark plug gap or heat range Set gap to specs or replace plug

Loose ignition connections Check all connections and tighten

Low battery voltage Recharge the battery to 12.8 VDC

Incorrect fuel Replace with fresh recommended fuel

Clogged air filter Inspect and clean or replace

Reverse speed limiter malfunction See your dealer

Electronic throttle control malfunction See your dealer

Other mechanical failure See your dealer

Overheated engine Clean radiator screen and core, clean engine exterior, see your dealer

Possible Cause Solution

Debris lodged in screen Remove and clean the screen. Pull on the top portion of the screen, then remove the lower portion.

Plugged Radiator Use a garden hose to flush any debris from the radiator fins. NOTE: High pressure washers can deform the radiator fins and reduce cooling efficiency.

127

DECLARATION OF CONFORMITY POLARIS Industries Inc., 2100 Hwy 55, Medina, MN 55340 U.S.A. Telephone 763-542-0500

We, POLARIS Industries Inc., declare that the vehicles listed below conform to the essential health and safety requirements applicable to off-road all-terrain vehicles.

PRODUCT IDENTIFICATION

European Vibration and Noise The driver-perceived noise and hand/arm and whole body vibration levels of this machinery is measured per prEN 15997. The operating conditions of the machinery during testing: The vehicles were in like-new condition. The environment was controlled as indicated by the test procedure(s). The uncertainty of vibration exposure measurement is dependent on many factors, including: Instrument and calibration uncertainty Variations in the machine such as wear of components Variation of machine operators such as experience or physique Ability of the worker to reproduce typical work during measurements

Environmental factors such as ambient noise or temperature

APPLICABLE EUROPEAN DIRECTIVES TEST / EVALUATION METHODS 2006/42/EC as amended (Machinery Directive) EN 1050 hazard analysis

prEN 15997 driver-perceived noise level prEN 15997 vibration

2004/108/EC as amended (EMC Directive) CISPR 12:2009 CAN/CSA-C108.4-M92

EN 55012:2007 EN 61000-6-2:2005

VEHICLE SERIES TRADE NAME MODEL YEARS

___MH50__ SPORTSMAN FOREST 500 2011 ___ZX55__ SPORTSMAN FOREST 550 2011 ___ZX85__ SPORTSMAN FOREST 850 2011

European Community Person Authorized to Compile the Technical File:

Ross Clifford, General Manager POLARIS Britain Ltd Forge Mills Park, Station Road Coleshill, Warwickshire B46 1HT

128

WARRANTY LIMITED WARRANTY POLARIS Industries Inc., 2100 Highway 55, Medina, MN 55340, gives a TWO YEAR LIMITED WARRANTY on all components of the POLARIS vehicle against defects in material or workmanship. This warranty covers the parts and labor charges for repair or replacement of defective parts which are covered by this warranty. This warranty begins on the date of purchase. This warranty is transferable to another consumer during the warranty period through a POLARIS dealer.

REGISTRATION At the time of sale, the Warranty Registration Form must be completed by your dealer and submitted to POLARIS within ten days. Upon receipt of this registration, POLARIS will record the registration for warranty. THE PURCHASER MUST COMPLETE A SAFETY TRAINING COURSE PROVIDED BY THE DEALER IN ORDER TO HAVE VALID WARRANTY ON THE VEHICLE. No verification of registration will be sent to the purchaser as the copy of the Warranty Registration Form will be the war- ranty entitlement. If you have not signed the original registration and received the "cus- tomer copy", please contact your dealer immediately. NO WARRANTY COVERAGE WILL BE ALLOWED UNLESS YOUR POLARIS VEHICLE IS REGISTERED WITH POLARIS. Initial dealer preparation and set-up of your vehicle is very important in ensuring trou- ble-free operation. Purchasing a machine in the crate or without proper dealer set-up will void your warranty coverage.

WARRANTY COVERAGE AND EXCLUSIONS: LIMITATIONS OF WARRANTIES AND REMEDIES The POLARIS limited warranty excludes any failures that are not caused by a defect in material or workmanship. This warranty does not cover accidental damage, normal wear and tear, abuse or improper handling. This warranty also does not cover any vehicle that has been altered structurally, modified, neglected, improperly maintained, used for rac- ing, or used for purposes other than for which it was manufactured, or for any damages which occur during trailer transit or as a result of unauthorized service or the use of unauthorized parts. In addition, this warranty does not cover physical damage to paint or finish, stress cracks, tearing or puncturing of upholstery material, corrosion, or defects in parts, components or the vehicle due to fire, explosions or any other cause beyond POLARIS' control.

129

WARRANTY LIMITATIONS OF WARRANTIES AND REMEDIES Warranty does not apply to parts exposed to friction surfaces, stresses, environmental conditions and/or contamination, for which they were not designed or not intended, including but not limited to the following items:

Warranty applies to the product only and does not allow for coverage of personal loss. Some items are considered "consumable," meaning they are considered part of normal maintenance or part of completing an effective repair. The following items are excluded from warranty coverage in the event of a warranty claim:

This warranty also excludes failures resulting from improper lubrication; improper engine timing; improper fuel; surface imperfections caused by external stress, heat, cold or contamination; operator error or abuse; improper component alignment, tension, adjustment or altitude compensation; failure due to snow, water, dirt or other foreign substance ingestion/contamination; improper maintenance; modified components; use of aftermarket components resulting in failure; unauthorized repairs; repairs made after the warranty period expires or by an unauthorized repair center; use of the product in competition or for commercial purposes. Warranty will not apply to any product which has been damaged by abuse, accident, fire or any other casualty not determined a defect of materials or workmanship.

Wheels and tires Finished and unfinished surfaces Suspension components Carburetor/Throttle body components Brake components Engine components Seat components Drive belts Clutches and components Hydraulic components Steering components Circuit breakers/Fuses Batteries Electronic components Light bulbs/Sealed beam lamps

Spark Plugs Lubricants such as oil, grease, etc. Filters Batteries (unless defective) Fuel Cosmetic damage/repair Sealants Coolants Hotel fees Meals Towing charges Shipping/ handling fees Mileage Product pick-up/delivery Rentals/Loss of product use Loss of vacation/personal time

130

WARRANTY LIMITATIONS OF WARRANTIES AND REMEDIES This warranty does not cover the use of unauthorized lubricants, chemicals, or fuels that are not compatible with the vehicle. The exclusive remedy for breach of this warranty shall be, at POLARIS' exclusive option, repair or replacement of any defective materi- als, or components or products. THE REMEDIES SET FORTH IN THIS WARRANTY ARE THE ONLY REMEDIES AVAILABLE TO ANY PERSON FOR BREACH OF THIS WARRANTY. POLARIS SHALL HAVE NO LIABILITY TO ANY PERSON FOR INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES OF ANY DESCRIPTION, WHETHER ARISING OUT OF EXPRESS OR IMPLIED WAR- RANTY OR ANY OTHER CONTRACT, NEGLIGENCE, OR OTHER TORT OR OTHERWISE. THIS EXCLUSION OF CONSEQUENTIAL, INCIDENTAL, AND SPECIAL DAMAGES IS INDEPENDENT FROM AND SHALL SURVIVE ANY FINDING THAT THE EXCLUSIVE REMEDY FAILED OF ITS ESSENTIAL PUR- POSE. Some states do not permit the exclusion or limitation of incidental or consequen- tial damages or implied warranties, so the above limitations or exclusions may not apply to you if inconsistent with controlling state law. ALL IMPLIED WARRANTIES (INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PAR- TICULAR PURPOSE) ARE LIMITED IN DURATION TO THE ABOVE TWO YEAR WARRANTY PERIOD. POLARIS FURTHER DISCLAIMS ALL EXPRESS WARRANTIES NOT STATED IN THIS WARRANTY. Some states do not allow limi- tations on how long an implied warranty lasts, so the above limitation may not apply to you if inconsistent with controlling state law.

HOW TO OBTAIN WARRANTY SERVICE If your vehicle requires warranty service, you must take it to a POLARIS dealer autho- rized to repair POLARIS vehicles. When requesting warranty service you must present your copy of the Warranty Registration form to the dealer. (THE COST OF TRANS- PORTATION TO AND FROM THE DEALER IS YOUR RESPONSIBILITY). POLARIS suggests that you use your original selling dealer; however, you may use any POLARIS Servicing Dealer to perform warranty service. Please work with your dealer to resolve any warranty issues. Should your dealer require any additional assistance they will contact the appropriate personnel at POLARIS. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. If any of the above terms are void because of state or federal law, all other warranty terms will remain in effect.

131

MAINTENANCE LOG Present this section of your manual to your dealer each time your vehicle is serviced. This will provide you and future owners with an accurate log of maintenance and ser- vices performed.

DATE KILOMETERS OR HOURS

TECHNICIAN SERVICE PERFORMED / COMMENTS

132

MAINTENANCE LOG

DATE KILOMETERS OR HOURS

TECHNICIAN SERVICE PERFORMED / COMMENTS

133

MAINTENANCE LOG

DATE KILOMETERS OR HOURS

TECHNICIAN SERVICE PERFORMED / COMMENTS

134

INDEX A

Accessories . . . . . . . . . . . . . . . . . . 118 Age Restrictions. . . . . . . . . . . . . . . . . 5 Air Filter . . . . . . . . . . . . . . . . . . . . . 92 All Wheel Drive Switch. . . . . . . . . . 34 All Wheel Drive System . . . . . . . . . 44 AWD System. . . . . . . . . . . . . . . . . . 44

B Battery . . . . . . . . . . . . . . . . . . 107-112

Charging (Conventional) . . . . 111 Charging (Sealed) . . . . . . 111-112 Fluid (Conventional) . . . . . . . 110 Installation . . . . . . . . . . . . . . . 109 Removal. . . . . . . . . . . . . . . . . 108 Storage . . . . . . . . . . . . . . . . . . 110

Belt Life . . . . . . . . . . . . . . . . . . . . . . 42 Boots . . . . . . . . . . . . . . . . . . . . . . . . 17 Brake Fluid . . . . . . . . . . . . . . . . . 82-84 Brake Inspections. . . . . . . . . . . . . . . 85 Brake, Foot . . . . . . . . . . . . . . . . . . . 38 Brake, Hand . . . . . . . . . . . . . . . . . . . 38 Brake, Parking . . . . . . . . . . . . . . . . . 39 Brakes . . . . . . . . . . . . . . . . . . . . . . . 85 Break-In Period . . . . . . . . . . . . . . . . 52 Breather Filter . . . . . . . . . . . . . . . . . 93 Breather Hose . . . . . . . . . . . . . . . . . 93

C Carburetor . . . . . . . . . . . . . . . . . . . . 79 Carburetor Adjustment . . . . . . . . . . 79 Cargo . . . . . . . . . . . . . . . . . . . . . . 32-33 Choke. . . . . . . . . . . . . . . . . . . . . . . . 41 Chrome Wheel Care . . . . . . . . . . . 115 Cleaning and Storage. . . . . . . . 113-118 Clothing . . . . . . . . . . . . . . . . . . . . . . 17 Clutching . . . . . . . . . . . . . . . . . . . . 121 Cold Weather Operation . . . . . . . . . 55 Coolant Bottle . . . . . . . . . . . . . . . . . 80 Coolant, Radiator. . . . . . . . . . . . . . . 81 Cooling System . . . . . . . . . . . . . . 80-81 Corrosion Removal, Chrome. . . . . 115

D Demand Drive Fluid . . . . . . . . . . 77-78 Drive Belt Wear/Burn . . . . . . . . . . . 123 Drivetrain Break-In . . . . . . . . . . . . . . 52 Driving Downhill. . . . . . . . . . . . . . . . 25 Driving in Reverse. . . . . . . . . . . . . . . 31 Driving on a Sidehill . . . . . . . . . . . . . 24 Driving on Slippery Surfaces . . . . . . 20 Driving Over Obstacles . . . . . . . . . . . 21 Driving Procedures . . . . . . . . . . . . . . 18 Driving Safely . . . . . . . . . . . . . . . 18-33 Driving Through Water . . . . . . . . 28-29 Driving Uphill . . . . . . . . . . . . . . . 22-23

E Electromagnetic Interference. . . . . . . 62 Electronic Throttle Control . . . . . . . . 37 Engine Break-In. . . . . . . . . . . . . . . . . 52 Engine Fogging . . . . . . . . . . . . . . . . 117 Engine Idle RPM Adjustment . . . . . . 79 Engine Oil . . . . . . . . . . . . . . . . . . 69-74 Equipment Modifications . . . . . . . . . . 5 Exhaust Emission Control System . . 62 Eye Protection . . . . . . . . . . . . . . . . . . 17

F Fluid

Brake . . . . . . . . . . . . . . . . . . 82-84 Demand Drive . . . . . . . . . . . 77-78 Engine Oil . . . . . . . . . . . . . . 69-74 Transmission . . . . . . . . . . . . 75-76

Fluid Change Demand Drive . . . . . . . . . . . . . . 78 Engine Oil . . . . . . . . . . . . . . . . . 72 Transmission . . . . . . . . . . . . . . . 76

Fluid Level Demand Drive . . . . . . . . . . . . . . 77 Engine Oil . . . . . . . . . . . . . . . . . 70 Transmission . . . . . . . . . . . . . . . 75

Fluid Recommendations Demand Drive . . . . . . . . . . . . . . 77 Engine . . . . . . . . . . . . . . . . . . . . 69 Transmission . . . . . . . . . . . . . . . 75

135

INDEX F

Foot Brake. . . . . . . . . . . . . . . . . . . . . 38 Footwell Removal. . . . . . . . . . . . . . . 88 Front Gearcase . . . . . . . . . . . . . . 77-78 Fuel Filter . . . . . . . . . . . . . . . . . . . . . 41 Fuel Safety . . . . . . . . . . . . . . . . . . . . 51 Fuel Tank Cap. . . . . . . . . . . . . . . . . . 41 Fuel Valve. . . . . . . . . . . . . . . . . . . . . 41 Fuse Replacement . . . . . . . . . . . . . . . 97

G Gear Selector. . . . . . . . . . . . . . . . . . . 42 Gloves . . . . . . . . . . . . . . . . . . . . . . . . 17

H Handlebar Adjustment . . . . . . . . . . . 87 Hauling Cargo. . . . . . . . . . . . . . . 32-33 Hazard Warning Switch . . . . . . . . . . 36 Headlight Beam Adjustment. . . . . . . 94 Headlight Lamp . . . . . . . . . . . . . . . . 95 Headlight Switch. . . . . . . . . . . . . . . . 35 Helmet. . . . . . . . . . . . . . . . . . . . . . . . 16 High Beam Switch, Momentary . . . . 34 High Range Use . . . . . . . . . . . . . . . 105 Horn Switch . . . . . . . . . . . . . . . . . . . 36

I-J-K Idle RPM Adjustment . . . . . . . . . . . . 79 Immersion . . . . . . . . . . . . . . . . 100-101 Instrument Cluster. . . . . . . . . . . . 45-50 Jetting Chart . . . . . . . . . . . . . . . . . . 121 Key Switch . . . . . . . . . . . . . . . . . . . . 35 K-Turn . . . . . . . . . . . . . . . . . . . . 26-27

L Light Switch . . . . . . . . . . . . . . . . . . . 34 Lights . . . . . . . . . . . . . . . . . . . . . 94-96

Front Turn Signal . . . . . . . . . . . 96 Headlight Beam Adjustment. . . 94 Headlight Lamp . . . . . . . . . . . . 95 Momentary High Beam Switch 34 Position Light Lamp . . . . . . . . . 95 Rear Turn Signal . . . . . . . . . . . . 96 Taillight. . . . . . . . . . . . . . . . . . . 96

Low Range Use. . . . . . . . . . . . . . . . 105 Lubrication Guide . . . . . . . . . . . . . . . 68

M Maintenance Chart . . . . . . . . . . . 63-67 Mirrors . . . . . . . . . . . . . . . . . . . . . . . 37 Mode Switch . . . . . . . . . . . . . . . . . . . 34 Modifications . . . . . . . . . . . . . . . . . . . 5

N Noise Emission Control System . . . . 62

O Oil

Demand Drive. . . . . . . . . . . 77-78 Engine Oil . . . . . . . . . . . . . . 69-74 Transmission. . . . . . . . . . . . 75-76

Oil Change Demand Drive. . . . . . . . . . . . . . 78 Engine Oil . . . . . . . . . . . . . . . . . 72 Transmission. . . . . . . . . . . . . . . 76

Oil Level Demand Drive. . . . . . . . . . . . . . 77 Engine Oil . . . . . . . . . . . . . . . . . 70 Transmission. . . . . . . . . . . . . . . 75

Oil Pump Priming . . . . . . . . . . . . . . . 74 Oil Recommendations

Demand Drive. . . . . . . . . . . . . . 77 Engine . . . . . . . . . . . . . . . . . . . . 69 Transmission. . . . . . . . . . . . . . . 75

Operator Safety . . . . . . . . . . . . . . . 7-13 Override Switch . . . . . . . . . . . . . . . . 34

P Parking Brake . . . . . . . . . . . . . . . . . . 39 Parking on an Incline . . . . . . . . . . . . 30 Periodic Maintenance Chart . . . . 63-67 Polaris Product List. . . . . . . . . . . . . 122 Polishing the Vehicle . . . . . . . . . . . 114 Position Light Lamp . . . . . . . . . . . . . 95 Pre-Ride Checklist . . . . . . . . . . . . . . 53 PVT Break-In . . . . . . . . . . . . . . . . . . 52 PVT Drying . . . . . . . . . . . . . . . . . . . 62 PVT System . . . . . . . . . . . . . . 104-105

136

INDEX R

Recoil Housing . . . . . . . . . . . . . . . 106 Recoil Starter . . . . . . . . . . . . . . . . . . 43 Reverse Operation . . . . . . . . . . . . . . 31 Reverse Override Switch . . . . . . . . . 34 Rider Information Center. . . . . . . 46-50 Riding Gear . . . . . . . . . . . . . . . . . 16-17

S Safety Labels . . . . . . . . . . . . . . . . 14-15 Safety Training . . . . . . . . . . . . . . . . . 5 Service Interval Programming. . . . . 50 Severe Use . . . . . . . . . . . . . . . . . . . . 63 Side Panel Removal. . . . . . . . . . . . . 88 Sidehilling . . . . . . . . . . . . . . . . . . . . 24 Signal Words . . . . . . . . . . . . . . . . . . . 4 Spark Arrestor . . . . . . . . . . . . . 102-103 Spark Arrestor Requirements . . . . . 62 Spark Plugs . . . . . . . . . . . . . . . . . 98-99 Specifications. . . . . . . . . . . . . . 120-121 Spring Adjustment, Rear . . . . . . . . . 87 Starting the Engine . . . . . . . . . . . 54-55 Steering Assembly . . . . . . . . . . . . . . 87 Steering Lock. . . . . . . . . . . . . . . . . . 40 Stop Switch . . . . . . . . . . . . . . . . . . . 35 Storage . . . . . . . . . . . . . . . . . . . 113-118 Switches . . . . . . . . . . . . . . . . . . . 34-36

AWD Switch . . . . . . . . . . . . . . 34 Engine Stop Switch . . . . . . . . . 35 Hazard Warning Switch. . . . . . 36 Headlight Switch . . . . . . . . . . . 35 Horn Switch . . . . . . . . . . . . . . . 36 Main Key Switch . . . . . . . . . . . 35 Mode/Reverse Override Switch 34 Momentary High Beam Switch 34 Turn Signal Switch . . . . . . . . . 36 Winch Switch . . . . . . . . . . . . . 34

T Taillight . . . . . . . . . . . . . . . . . . . . . . . 96 Throttle Cable Freeplay . . . . . . . . . . . 89 Throttle Lever . . . . . . . . . . . . . . . . . . 37 Tire Tread Depth . . . . . . . . . . . . . . . . 90 Tires . . . . . . . . . . . . . . . . . . . . . . 90-91

Front Wheel Hub Tightening. . . 90 Tread Depth . . . . . . . . . . . . . . . . 90 Wheel Installation . . . . . . . . . . . 91 Wheel Nut Torque . . . . . . . . . . . 90 Wheel Removal . . . . . . . . . . . . . 91

Toe Alignment. . . . . . . . . . . . . . . . . . 86 Towing a Disabled Vehicle . . . . . . . 119 Towing Loads . . . . . . . . . . . . . . . . . . 33 Training, Safety . . . . . . . . . . . . . . . . . . 5 Transmission Oil . . . . . . . . . . . . . 75-76 Transporting the Vehicle . . . . . . . . . 119 Turn Signal Lamp, Rear . . . . . . . . . . 96 Turn Signal Replacement, Front . . . . 96 Turn Signal Switch . . . . . . . . . . . . . . 36 Turning Around on a Hill . . . . . . 26-27 Turning the Vehicle . . . . . . . . . . . . . . 19

V Vehicle Identification Numbers. . . . . . 6 Vehicle Immersion . . . . . . . . . 100-101

W Warning Symbols . . . . . . . . . . . . . . . . 4 Washing the Vehicle . . . . . . . . 113-114 Wheel Hub Tightening . . . . . . . . . . . 90 Wheel I

Manualsnet FAQs

If you want to find out how the Sportsman Forest 500 Polaris works, you can view and download the Polaris Sportsman Forest 500 Owner's Manual on the Manualsnet website.

Yes, we have the Owner's Manual for Polaris Sportsman Forest 500 as well as other Polaris manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Owner's Manual should include all the details that are needed to use a Polaris Sportsman Forest 500. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Polaris Sportsman Forest 500 Owner's Manual is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Polaris Sportsman Forest 500 Owner's Manual consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Polaris Sportsman Forest 500 Owner's Manual free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Polaris Sportsman Forest 500 Owner's Manual, simply download the document to your computer. Once downloaded, open the PDF file and print the Polaris Sportsman Forest 500 Owner's Manual as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.