Contents

Philips Screeneo HDP1590TV Projector User Manual PDF

1 of 40
1 of 40

Summary of Content for Philips Screeneo HDP1590TV Projector User Manual PDF

Register your product and get support at

www.philips.com/welcome Screeneo

HDP1550 HDP1550TV

HDP1590 HDP1590TV

EN User Manual

LU Screeneo_EN.book Page 1 Jeudi, 11. dcembre 2014 8:37 08

2 Philips HDP15x0 & HDP15x0TV

Table of Contents Overview ...................................................3 Dear Customer ....................................................................3 About this User Manual ......................................................3 What's in the Box ................................................................3 Product Highlights ...............................................................3

1 General Safety Information ................4

Setting up the Device ..........................................................4 Automatic device temperature control ..........................4 Repairs ....................................................................................4 Power Supply ........................................................................5 Wireless Network (WLAN) .............................................5 3D glasses use .......................................................................5 Dolby Digital .........................................................................5

2 Overview ...............................................6

Front View .............................................................................6 Rear View ..............................................................................6 Remote Control ...................................................................7 Browsing the user interface ...............................................8 Overview of the Menu Functions .....................................8 Symbols in the Statusbar ....................................................9

3 Initial Operation ................................10

Setting up the Device ........................................................10 Connect Power Supply .....................................................10 Installing or Changing the Batteries of the Remote Control .................................................................10 Using the Remote Control ..............................................11 Initial Installation .................................................................12

4 Connect to the Playback Device ......13

Connecting to Devices with HDMI Output ................13 Connecting to a Computer (VGA) ................................13 Connecting Using an Audio/Video (CVBS) Adapter Cable .....................................................................................14 Connecting to a home cinema amplifier .......................14 Connecting to a Hi-Fi unit ...............................................14 Connecting the headphones ............................................15 WiFiDisplay (Miracast) ......................................................15 ScreeneoWLink software ................................................15

5 Memory ...............................................18

Inserting a Memory Card .................................................18 Connecting USB Storage Medium ..................................18

6 Network ..............................................19

LAN Network ....................................................................19 Wireless Network (WLAN) ...........................................19 Switching Wireless Networking (WLAN) on/off .......20 Setting up a Wireless Network (WLAN) ....................20

Setting up a Wireless Network (WLAN) using the Wizard .......................................................................... 20 Wifi Hotspot ....................................................................... 21 Digital Living Network Alliance (DLNA) ..................... 22

7 Bluetooth ........................................... 23

Activating the Bluetooth connection ............................ 23 Setting up Bluetooth parameters ................................... 23 Bluetooth speaker ............................................................. 23

8 Media Playback .................................. 25

Navigating in the media Playback ................................... 25 Video playback .................................................................... 26 Photo Playback ................................................................... 26 Music Playback .................................................................... 28 Managing Files ..................................................................... 29

9 Digital TV Playback (Depending on model) ................................................ 30

Connecting the Aerial ...................................................... 30 First Playback ...................................................................... 30 Television ............................................................................. 30 Modifying the DVB-T settings ......................................... 31

10 Android ............................................... 32

Starting Android Apps ...................................................... 32 Exiting Android .................................................................. 32 Installing Android-Apps .................................................... 32

11 Settings ............................................... 33

Overview of the Menu Functions .................................. 33

12 Service ................................................ 35

Cleaning ............................................................................... 35 Device Overheated ........................................................... 35 Update Firmware with Memory Card .......................... 35 Troubleshooting ................................................................. 36

13 Appendix ............................................ 38

Technical Data .................................................................... 38 Accessories ......................................................................... 38

LU Screeneo_EN.book Page 2 Jeudi, 11. dcembre 2014 8:37 08

LU Screeneo_EN.book Page 3 Jeudi, 11. dcembre 2014 8:37 08

Overview

Dear Customer Thank you for purchasing our projector.

We hope you enjoy your device and its many functions!

About this User Manual With the installation guide on the following pages, you can start using your device quickly and easily. Detailed descriptions can be found in the following sections of this user manual.

Read the entire user manual carefully. Follow all safety instructions in order to ensure proper operation of your device. The manufacturer accepts no liability if these instructions are not followed.

This user manual describes several versions of the prod- uct. Only the models HDP1590 and HDP1590TV have the WiFi (Miracast, DLNA,..) and Bluetooth functions.

Only the models HDP1550TV and HDP1590TV have the DVB-T function.

Symbols Used

What's in the Box 1 Projector

2 Remote Control (with 2AAA battery)

3 A/C power cable

4 HDMI A to A cable

5 3D Glasses with his quick start guide, a warning label and a protection bag (depending on model)

6 Quick Start Guide

7 Warranty Guide

8 Bag

Product Highlights Connecting to devices with HDMI output With the HDMI cable you can connect the projector to a computer or laptop (see Connect to the Playback Device, page 13).

WiFiDisplay (Miracast) With the Miracast solution you can display video between Wi-Fi devices, without cables or a network connection. You can do things like view pictures or vid- eos from a smartphone or laptop on your projector.

Notice Troubleshooting This symbol designates tips that will help you to use your device more effectively and easily.

CAUTION!

Damage to the Device or Loss of Data! This symbol gives warning of damage to the device and possible loss of data. This damage can result from improper handling.

DANGER!

Danger to Persons! This symbol gives warning of danger to per- sons. Physical injury or damage can result from improper handling.

d

f g

b c a

e

7 8 9

4 5 6

1 2 3

0

TUV WXYZPQRS

GHI JKL MNO

. @ ABC DEF

SUBTITLE TEXT

CH - CH +

EXIT OPTIONS

LIST INFO

SOURCE FORMATTV

SMART TV

GUIDE 3D AMBILIGHT

PHILIPS

OK

h

3

LU Screeneo_EN.book Page 4 Jeudi, 11. dcembre 2014 8:37 08

1 General Safety Information Do not make any changes or settings that are not described in this user manual. Physical injury or damage to the device or loss of data can result from improper handling. Take note of all warning and safety notes indi- cated.

Setting up the Device The unit is for indoor use only. The device should be placed securely on a stable, flat surface. Position all cables in such a way that no one will stumble on them, thus avoiding possible injuries to persons or damage to the device itself.

Do not plug in the device in moist rooms. Never touch the mains cable or the mains connection with wet hands.

The device must have sufficient ventilation and may not be covered. Do not put your device in closed cabinets or boxes.

Do not place the machine on soft surfaces such as table- cloths or carpets and do not cover the ventilation slits. Otherwise the device could overheat or catch fire.

Protect the device against direct sunlight, heat, large temperature fluctuations and moisture. Do not place the device in the vicinity of heaters or air conditioners. Observe the information on temperature and humidity in the technical data.

Do not allow liquids to enter into the device. Switch off the device and disconnect it from the mains supply if liq- uids or foreign substances end up inside the device. Have the unit inspected by a technical service depart- ment.

Always handle the unit with care. Avoid touching the lens. Never place heavy or sharp objects on the projec- tor or the power cable.

If the projector gets too hot or emits smoke, shut it down immediately and unplug the power cable. Arrange for your device to be investigated by a technical service centre. To prevent the spread of fire, open flames should be kept away from the device.

Under the following conditions, a layer of moisture can appear inside the device which can lead to malfunctions:

if the device is moved from a cold to a warm area;

after a cold room is heated; when this device is placed in a damp room.

Proceed as follows to avoid any moisture build-up:

1 Seal this device in a plastic bag before moving it to another room, in order for it to adapt to room con- ditions.

2 Wait one to two hours before you take the device out of the plastic bag.

The device should not be used in a very dusty environ- ment. Dust particles and other foreign objects may damage the unit.

Do not expose the device to extreme vibrations. It may damage the internal components.

Do not allow children to handle the device without supervision. The packing materials should be kept out of the hands of children.

Automatic device temperature control This device include an automatic thermal management controller. If the internal temperature gets too hot, the Fan speed will automatically increase (noise increase), if the temperature still continue to growth, the brightness of your product will decrease and in worst case the cur- rent symbol will appear.

The product will automatically switch off the display after displaying this message during 5s.

This kind of behaviour should not arrive except if the outside temperature is very high (>35C). In such case return the product to the manufacturer would be rec- ommended.

Repairs Do not repair the device yourself. Improper mainte- nance can result in injuries or damage to the device. Your device must be repaired by an authorised service centre.

Find details of authorised service centres on the war- ranty card.

Do not remove the type label from your device; this would void the warranty.

4 Philips HDP15x0 & HDP15x0TV

LU Screeneo_EN.book Page 5 Jeudi, 11. dcembre 2014 8:37 08

Power Supply Before turning on your device, check that the outlet that you are going to plug it into conforms to the indi- cations shown on the information plate (voltage, cur- rent, power network frequency) located on your device. This device shall be connected to a single phase power network. The device shall not be installed on bare ground.

Only use the power cable that is supplied with your device. Your device is delivered with a grounded power cord. It is imperative to connect a grounded connector to a grounded outlet connected to the building earthing.

The socket outlet shall be installed near the equipment and shall be easily accessible.

In case of failure, the power cable is the disconnect device for this equipment. To remove all electrical power from the equipment, disconnect the power cable from the electrical outlet.

Turn off the device and unplug from the power outlet before cleaning the surface. Use a soft, lint-free cloth. Never use liquid, gaseous or easily flammable cleansers (sprays, abrasives, polishes, alcohol). Do not allow any moisture to reach the interior of the device.

Wireless Network (WLAN) The functioning of security systems, medical equipment or sensitive devices can be disrupted by the transmis- sion power of the device. Observe any usage regula- tions (or restrictions) in the vicinity of such equipment.

The use of this device can affect the operation of insuf- ficiently shielded medical devices and hearing aids and pacemakers through the release of high frequency radi- ation. Also consult a doctor or the manufacturer of the medical device to establish whether these are suffi- ciently shielded from external high frequency radiation.

3D glasses use The use of 3D glasses in home for watching TV shows:

is contraindicated for children less than 6 years old;

for subjects from 6 years old to adulthood, should be limited to the vision for a maximum time equal to the duration of a film show;

the same time limit is also recommended for adults;

must be restricted to watching only 3D content

how to make a proper and regular cleaning and disinfection in the case of any particular eventu- alities-ocular infections, infestations of the head, mixed use, etc. .. where disinfection of the glasses is not possible as it may damage the func- tionality of the 3D glasses must be communi- cated to the consumer that in presence of these eventualities-infections is contraindicated the use of 3D glasses for the person concerned until the disappearance of the above circumstances;

3D glasses must be kept out of children if there is the presence of small moving parts ingestible;

3D glasses are to be used together with the instruments of vision correction in case the con- sumer is the bearer of lenses (eyeglasses or con- tact lenses);

You should stop watching 3D in the event of the occurrence of eye problems or discomfort, and in the event of a persistence of the same, consult a doctor.

Dolby Digital Manufactured under license from Dolby Laboratories. Dolby and the double-D symbol are trademarks of Dolby Laboratories.

DANGER!

High Power LED This device is equipped with high power LED (Light Emitting Diode), which emit very bright light. Do not look directly into the projector lens. This could cause eye irritation or dam- age.

General Safety Information 5

LU Screeneo_EN.book Page 6 Jeudi, 11. dcembre 2014 8:37 08

2 Overview

Front View 1 Control panel for navigation and operation

u To display the home menu

One menu step back, one directory level back / cancelling a function

/// Navigation keys / navigate the menu / modify settings

Confirms selection

B Long press: Power on /off the projector Short press: ECO mode on / off

2 Audio output headphone connection or con- nection for external speakers

3 3 HDMI port for a playback device

4 Memory card slot

5 USB port for a USB storage medium or to con- nect accessories (mouse or keyboard).

6 Focus wheel for image sharpness

Rear View 1 Power supply outlet

2 2 USB ports for a USB storage medium

3 Digital audio connector

4 HDMI 1 and 2 ports for a playback device

5 Kensington Security System Connector

6 VGA Personal Computer input

7 LAN network connector

8 Analog audio connectors

9 / A/V port for a playback device

Remote screen connection

Aerial socket for TV connection

Lens

PHILIPS

a

b c

d e

f

PHILIPS

VGA

1 2 S/PDIF OPTICAL

AUDIO OUT TRIG

OUT

AV IN

L

R

a

b c d e

j i

g f

h

6 Philips HDP15x0 & HDP15x0TV

LU Screeneo_EN.book Page 7 Jeudi, 11. dcembre 2014 8:37 08

Remote Control

1 Long press: Power off the projector. To power the projector on use the B key on the control panel. Short press: ECO mode on / off

2 Playback keys

Skip backward (music only)

To stop playback

Skip forward (music only)

To rewind

To start / pause playback

To fast-forward

3 EPG To display the electronic program guide. 3D To display the 3D menu. Favorite To display the favourite list in DVB-T mode.

4 To display the home menu.

5 TAB key or Toggle between TV and Radio chan- nels in DVB-T mode and browsing the Internet without external keyboard.

6 Navigation keys Confirms selection

/, / Navigation keys / navigate the menu / modify settings.

7 EXIT One menu step back, one directory level back / cancelling a function.

8 PAGE/CH- PAGE/CH+ To select the previous channel/page or the next channel/page.

9 Color keys - On-screen options.

Number keys and text keypad.

Short press for numbers and long press to switch "letters"

SUB/SHIFT To display subtitles in DVB-T mode or shift key in input mode.

TTX/ To display Teletext pages when availa- ble in DVB-T mode or backspace key in input mode.

/ + To adjust the volume level (to decrease/ increase and to mute the sound).

RECALL To recall the last function or the last channel viewed in DVB-T mode.

OPTIONS To call the option menu.

INFO To display program information on current program in DVB-T mode.

MENU To display the settings menu in DVB-T mode.

SOURCE To display the list of input connections.

SMART SETTINGS To display the Smart set- tings menu

FORMAT To change the aspect ratio.

7 8 9

4 5 6

1 2 3

0

TUV WXYZPQRS

GHI JKL MNO

. @ ABC DEF

SUB/SHIFT

PAGE/CH -

EXIT OPTIONS

TAB INFO

SOURCE FORMATSETTING

MENU

EPG 3D FAVORITE

PHILIPS

OK

RECALL

PAGE/CH +

TTX/

SMART

a

b

c

e d

f

g

h

i

j

Overview 7

LU Screeneo_EN.book Page 8 Jeudi, 11. dcembre 2014 8:37 08

Browsing the user interface

Navigation for setting menu Navigation can be done by navigation keys (,, ,, OK and ) on the control panel or the re- mote control, as well as by an air mouse.

Navigation by keys: / scrolls trough the menu level up and

down. OK/ goes one level down, with / one

level up. u goes back to the main screen. In the final level, accepts a setting and goes

back to the last sub menu. The key aborts a setting and goes back to the

last sub menu (or exits the menu depending on which menu)

Navigation by (air) mouse: (like standard mouse operation within Android)

Select an icon by pointing with the mouse pointer and clicking with the left mouse key.

If there are more menus listed than displayed you can scroll the list by clicking into the list and move up and down without releasing the left mouse button.

With the right mouse key you can exit the menu and go back to the next top level menu.

Software Keyboard

When you need to enter data, the projector displays a virtual keyboard which allows you to enter text, num- bers and punctuation marks, etc.

1 Select the input field using the ,, and keys, then press the OK key to display the keyboard or click in the input field using the air mouse.

2 The software keyboard appears.

3 Enter the text on the software keyboard.

Overview of the Menu Functions 1 After switching on the device the main menu

appears.

2 Select the desired menu using the navigation keys /, /.

3 Confirm with OK.

4 By pressing the u key you will return to the main menu.

HDMI 1, 2, & 3 Switch to the external video input HDMI. TV1 Television DLNA Displays the list of the devices found on the Network. Memory Display the content of the internal mem- ory and the inserted memory SD-Card (movies, pic- tures, musics, folderview). USB Display the content of the connected USB media (movies, pictures, musics, folderview). WWW Open an Internet web browser. VGA Switch to the Personal computer input. A/V-in Switch to the Audio Video input. APPs Call the android operating system.

Settings Configure settings for the wished used of the device.

CAUTION!

Air mouse The air mouse is not provided.

Notice To enter text, you can also use standard com- puter keyboard or mouse. It is possible to use wired models (USB) as well as wireless mod- els with 2.4 GHz USB-connectors.

1.Depending on the device model, TV can be replaced by BT speaker.

8 Philips HDP15x0 & HDP15x0TV

LU Screeneo_EN.book Page 9 Jeudi, 11. dcembre 2014 8:37 08

Symbols in the Statusbar

1 Time

2 Date

3 LAN status display

4 Bluetooth status display

5 WiFi status display

a b dc e

Overview 9

LU Screeneo_EN.book Page 10 Jeudi, 11. dcembre 2014 8:37 08

3 Initial Operation

Setting up the Device Before installing your device, make sure that the projector is turned off and the power cord is unplugged from the power outlet. You can position the device so that it lies flat on a table in front of the projection surface; it is not necessary to tilt it towards the projection surface. The device com- pensates for the distortion from the slanted projection (pincushion distortion).

Check that the projection surface is appropriated to the projector. The distance between the projector and the screen determines the actual size of the image.

To change the size of the screen, just move the projec- tor towards or away from the wall.

The size of the screen (b) is comprised between 50 and 100 inches depending on the projection distance (a), as described in the following table.

Connect Power Supply

1 Connect the power cord into the socket on the rear side of your device (1).

2 Plug the power cord to outlet on the wall (2).

Installing or Changing the Batteries of the Remote Control

1 To access the battery, press to unlock the locking mechanism (1) and slide out the battery compart- ment (2).

2 Insert the new batteries into the battery compart- ment with the positive and negative poles as shown. Make sure the polarities(+ and -) are aligned cor- rectly.

Diagonal size (b) (mm) [inch]

Projection distance (a)

(mm)

1270

[50]

108

2540

[100]

441

CAUTION!

The power cord is used as a power unit cut off. As a precaution, the outlet shall be located close to the device and be of easy access in case of danger.

a

b

DANGER!

Risk of Explosion with Incorrect Type of Batteries Only use the AAA type battery.

There is a risk of explosion if the incor- rect battery type is used.

PHILIPS

VGA

1 2 S/PDIF OPTICAL

AUDIO OUT TRIG

OUT

AV IN

L

R

10 Philips HDP15x0 & HDP15x0TV

LU Screeneo_EN.book Page 11 Jeudi, 11. dcembre 2014 8:37 08

3 Push the battery compartment back into the remote control until the locking mechanism engages.

Using the Remote Control The remote control can be used within an angle of 22.5 degrees and up to 10 meters from the device. When using the remote control, no obstacle should be placed between the remote control and remote sensor.

Notice Normally the batteries will last for around one year. If the remote control stops working, please replace the batteries. If the device is not used for a long time, take out the batter- ies. This will prevent leakage and possible damage to the remote control.

The used batteries should be disposed of according to the recycling regulations of your country.

CAUTION!

The improper use of batteries can lead to overheating, explosion, risk of fire and injury. Leaking batteries can possibly damage the remote control.

Never expose the remote control to direct sunlight.

Avoid deforming, dismantling or charg- ing the batteries.

Avoid exposure to open fire and water. Replace empty batteries immediately. Remove the battery from the remote

control if not in use for long periods of time.

PHILIPS

22,5 22,5

7 8 9

4 5 6

1 2 3

0

TUV WXYZ PQRS

GHI JKL MNO

. @ ABC DEF

SUBTITLE TEXT

PAGE/CH - PAGE/CH +

EXIT OPTIONS

TAB INFO

SOURCE FORMAT

SETTINGS

MENU

EPG 3D FAVORITE

PHILIPS

OK

RECALL

SMART

Initial Operation 11

LU Screeneo_EN.book Page 12 Jeudi, 11. dcembre 2014 8:37 08

Initial Installation 1 Push the POWER B button for 5 seconds till the

power indicator turns to red to turn the device on.

2 Turn the device towards a suitable projection sur- face or wall. Note that the distance to the projection surface must be a minimum of 0.1 meter and a max- imum of 0.5 meter (see Setting up the Device, page 4). Make sure the projector is in a secure posi- tion.

3 Use the focus wheel on the font of the device to adjust the image sharpness.

4 The first time you turn on the device, you should set the following settings.

5 Use the keys / to select the language and con- firm with OK.

6 Use the keys /// to select the symbol + or - to set the date (day, month and year) and con- firm with .

7 Use the keys / to select the date format and confirm with .

8 Use the keys / to select the time zone and confirm with .

9 Use the keys /// to select the symbol + or - to set the date (hour and minute) and confirm with .

10 Use the keys / to select the time format (12h or 24h) and confirm with .

11 Use the keys / to select the location (Home or Shop) and confirm with . Home: for normal use. Shop: when you choose this option, the projector starts in demonstration mode. In this mode, the pro- jector automatically displays the pictures or videos stored in the internal memory in loop.

12 A message is displayed to give the address web site where the user manual can be downloaded. Press to continue.

Turning off the projector Press the B button on the panel control of the device or on the remote control more than 5 seconds.

ECO mode Press shortly the B button on the panel control or on the remote control to put the device in ECO mode.

To wake up the device, press shortly again on the B button.

Setting up the Language The device has already been installed. In order to change the menu language, proceed as follows:

1 Use the navigation keys to select Settings.

2 Confirm with .

3 Select Language/ Language with /.

4 Confirm with .

5 Select Menu Language with /.

6 Confirm with .

7 Select you desired language with /.

8 Confirm with .

9 Exit with u.

Notice During the first installation, use OK key to validate your choice and continue to the next step, and the key to return on the previ- ous step.

Notice The demonstration mode can be activated or deactivated on the menu Setting/Mainte- nance/Demo mode.

12 Philips HDP15x0 & HDP15x0TV

LU Screeneo_EN.book Page 13 Jeudi, 11. dcembre 2014 8:37 08

4 Connect to the Playback Device Supplied cables HDMI cable

Connecting to Devices with HDMI Output Use the HDMI cable to connect the projector to a com- puter, laptop or others devices.

1 Switch the device on using the on/off key.

2 Connect the cable to the projector's HDMI socket.

3 Connect the cable to the HDMI socket of the play- back device.

4 From the main menu, select HDMI 1,2 or 3 depend- ing on the external device is connected.

Connecting to a Computer (VGA)

Use the VGA cable (not included) to connect the pro- jector to a computer, laptop, or some PDAs. The pro- jector supports the following resolutions: VGA/SVGA/ XGA. For best results, please check the best resolution.

1 Switch the device on using the on/off key.

2 Connect the VGA cable to the projector's VGA socket.

3 Connect the VGA plug to the VGA socket of the computer.

4 Adjust the computer's resolution to the correct set- ting and switch the VGA signal to an external moni- tor. The following resolutions are supported:

5 From the main menu, select VGA.

Notice Use the HDMI socket 1 or 2 to connect the projector to a DVD player when a 3D signal is broadcasted.

PHILIPS

PHILIPS

VGA

1 2 S/PDIF OPTICAL

AUDIO OUT TRIG

OUT

AV IN

L

R

HDMI 3

HDMI 1 & HDM 2

Notice Many laptops do not activate the external video output automatically when you connect a second display such as a projector. Check your laptop's manual to find out how to acti- vate the external video output.

Resolution Image refresh rate

VGA 640 x 480 60 Hz

SVGA 800 x 600 60 Hz

XGA 1024 x 768 60 Hz

WXGA 1280 x 768 60 Hz

FULL HD 1920 x 1080 60 Hz

Notice Screen Resolution For best results, please check the best resolu- tion.

PHILIPS

VGA

1 2 S/PDIF OPTICAL

AUDIO OUT TRIG

OUT

AV IN

L

R

VGA

Connect to the Playback Device 13

LU Screeneo_EN.book Page 14 Jeudi, 11. dcembre 2014 8:37 08

Connecting Using an Audio/ Video (CVBS) Adapter Cable Use the projector's audio/video adapter cable (A/V cable) (not included) to connect camcorders, DVD players or digital cameras. The jacks for these devices are yellow (video), red (audio right) and white (audio left).

1 Connect the A/V adapter to the socket of the projector.

2 Connect the video device's audio/video sockets to the A/V cable using a conventional composite video (RCA) cable.

3 From the main menu, select AV-in. Connecting to mobile multimedia devices Some video devices (e.g.: pocket multimedia players, ...) require specific connection cables. There are either supplied with the device or acquired from the manufac- turer of the multimedia device. Please note that only the original cables from the device manufacturer may func- tion.

Connecting to a home cinema amplifier Use a S/PDIF optical cable (cable not provided) to con- nect the DIGITAL AUDIO output on the projector to the input of your home cinema amplifier. For example, to show digital channels in DTS or DOLBY DIGITAL quality sound.

Connecting to a Hi-Fi unit It is possible to use an analog audio connection, just connect the right and left audio outputs of the Projector to the auxiliary input of your Hi-Fi system (cable not provided).

Notice Switching to the Multimedia Device Sig- nal Output See the multimedia device instruction manual to find out how to switch the signal output to this jack.

PHILIPS

VGA

1 2 S/PDIF OPTICAL

AUDIO OUT TRIG

OUT

AV IN

L

R

AV IN

PHILIPS

VGA

1 2 S/PDIF OPTICAL

AUDIO OUT TRIG

OUT

AV IN

L

R

AV IN

PHILIPS

VGA

1 2 S/PDIF OPTICAL

AUDIO OUT TRIG

OUT

AV IN

L

R

S/PDIF OPTICAL

PHILIPS

VGA

1 2 S/PDIF OPTICAL

AUDIO OUT TRIG

OUT

AV IN

L

R

AUDIO OUT

14 Philips HDP15x0 & HDP15x0TV

LU Screeneo_EN.book Page 15 Jeudi, 11. dcembre 2014 8:37 08

Connecting the headphones 1 Before connecting the headphones, turn down the

volume on the device.

2 Connect the headphones to the projector's head- phone slot. The device speakers deactivate automat- ically when the headphones are connected.

3 After connecting the headphones, increase the vol- ume to a comfortable level.

WiFiDisplay (Miracast)

1 Switch the device on using the on/off key.

2 After the initial screen the main menu appears.

3 Use the navigation keys to select APPs.

4 Confirm with .

5 Use the navigation keys to select WifiDisplay.

6 Confirm with .

7 Connect the external device (smartphone or tablet) to the same WiFi network that the projector.

8 Select on the WifiDisplay application of the external device the name of the projector connection (in the example Screeneo_5f31).

9 Connect the external device (smartphone or tablet) to the projector, it will show up connecting.

10 In the WifiDisplay application of the projector, it will show up the message Invitation to connect, Decline or Accept, select Accept.

ScreeneoWLink software It allows to connect the projector to a desktop PC or laptop via the wireless or wired network and to use the Screeneo as computer screen.

For this, both devices must be connected to the same wireless or wired network.

Screeneo firmware version 1.20 must be installed on your projector.

Check the version of firmware installed on your projec- tor by going to the Settings menu > Maintenance > Firmware version.

If the Screeneo firmware version is 1.20, refer to para- graph Install the ScreeneoWLink software on my com- puter.

If the Screeneo firmware version is less than 1.20, refer to paragraph Update the software in my projector.

Update the software in my projector You can find the Screeneo firmware version on the site Philips : www.philips.com/screeneo for loading the file proceed as following

You must download the file on SD-card formatted FAT16 or FAT32, on USB stick or on USB digital sup- port in order to update your Screeneo.

Get yourself a suitable digital media and insert it into your computer.

1 Launch an Internet browser, in the address bar, type the address: www.philips.com/screeneo.

2 Choose your country and click on the language.

3 Click on View All 4 Products for select your model.

4 Select exactly your model with mouse.

5 In the new screen, research Support and click on.

6 The "Screeneo Smart LED projector" screen appears. In the "Software & drivers" select your language and click Download file.

7 Depending on the browser used, save the file in the root of your digital media.

DANGER!

Danger of Hearing Damage Do not use the device over a longer time at high volume especially when using head- phones. This could lead to the risks of hearing damage. Before connecting the headphones, turn down the volume on the device. After connecting the headphones, increase the vol- ume to a comfortable level.

Notice Only the Miracast-certified devices can be used with this function.

Notice The projector must be connected to a WiFi network.

Notice The name used to identify the projector can be modified in the Setting menu.

PHILIPS

Notice The file on the website is a zip file. It has to be unpacked and put on the root folder of the SD-card or USB-stick.

Connect to the Playback Device 15

LU Screeneo_EN.book Page 16 Jeudi, 11. dcembre 2014 8:37 08

8 On the Screeneo projector, to check that it is turned off (OFF).

9 Remove the digital media on your computer and insert it into the port of Screeneo for your digital media.

10

11 Long press the ON/OFF button on the projector to turn it on.

12 After the initial screen, the main menu appears. Use the navigation keys to select Settings.

13 Confirm with OK.

14 Use / to select Maintenance.

15 Confirm with OK.

16 Use / to select Firmware Update.

17 Confirm with OK.

18 Use / to select Install.

19 Confirm with OK.

20 The device turns off and on again. After around 5 minutes the Language Selection screen appears. The firmware update is now completed.

Copy the software on digital media (eg USB-stick) Use the USB ports on the projector to insert digital media.

1 Use / to select APPs.

2 Confirm with OK.

3 Use / to select Explorer.

4 Confirm with OK.

5 Use / to select Internal Flash.

6 Confirm with OK.

7 Use to select Download.

8 ScreeneoWLink_Setup.exe file appears in the main window.

9 Press long OK button on the remote control.

10 Use / to select Copy.

11 Confirm with OK.

12 Use /// you move on to the digital media that you have connected.

13 Confirm with OK.

14 Press long OK button on the remote control.

15 Use / to select Paste.

16 Confirm with OK.

17 ScreeneoWLink_Setup.exe file is copied to the digi- tal media. Wait that it appears in the browser win- dow before removing the digital media projector.

Install the ScreeneoWLink software on my computer 1 Insert the digital media containing the Screene-

oWLink_Setup.exe file on an appropriate port on your computer.

2 On desktop PC or laptop, select the digital media containing the file and double click the executable.

3 Follow the instructions that appear on the screen.

4 Agree to have the ScreeneWLink icon on your desk- top.

5 When installation is complete, restart your com- puter.

Link your projector and computer with WiFi Both devices must be connected to the same access point, no other network connection must be activated.

As a precaution, note the name and the key to protec- tion of your access point.

On the Screeneo, 1 Use / to select Settings.

2 Confirm with OK.

3 Using / select Wireless and Networks.

4 Confirm with OK.

5 Using / select WIFI.

6 Confirm with OK.

7 Using / select the desired wireless network.

8 Confirm with OK.

9 If your network is protected by a password, a win- dow appears. Select the input field with the naviga- tion buttons on the remote and press OK. A virtual keyboard appears, using the navigation keys on the remote control, witch a mouse or external keyboard. Enter your password.

10 Click Connect.

DANGER!

Inserting the digital media! Never pull out the digital media while the device is accessing it. This could cause data to be damaged or lost.

Switch the device off in order to make sure that the device does not access the memory card.

Notice If an error occurs during the firmware update process retry the procedure or contact your dealer.

16 Philips HDP15x0 & HDP15x0TV

LU Screeneo_EN.book Page 17 Jeudi, 11. dcembre 2014 8:37 08

Start ScreeneoWLink on your PC 1 Open the Start menu. Locate and open the Scree-

neoWLink tab. Click on ScreeneoWLink or double click on ScreeneoWLink icon of your desktop.

2 The ScreeneoWLink V1.2 software opens on the screen.

3 Stand on the projector image with the magnifying glass and click it.

4 Click Search.

5 Select and click on the Screeneo where you want to connect.

6 If necessary, enter password of acces point selected.

You can enjoy the Screeneo as screen for your PC.

Connect to the Playback Device 17

LU Screeneo_EN.book Page 18 Jeudi, 11. dcembre 2014 8:37 08

5 Memory

Inserting a Memory Card

1 Insert a memory card with the contacts facing upwards into the / slot at the back of the device. Your device supports the following memory cards: SD/SDHC/SDXC/MMC.

2 Insert the memory card into the slot until it snaps into position.

3 Press lightly on the memory card to remove it.

4 The memory card is ejected.

Connecting USB Storage Medium

1 Connect the USB storage medium to one USB port of the device.

DANGER!

Inserting a Memory Card! Never pull out the memory card while the device is accessing it. This could cause data to be damaged or lost.

Switch the device off in order to make sure that the device does not access the mem- ory card.

PHILIPS

DANGER!

Inserting a Memory Card! Never pull out the memory card while the device is accessing it. This could cause data to be damaged or lost.

Switch the device off in order to make sure that the device does not access the mem- ory card.

PHILIPS

PHILIPS

VGA

1 2 S/PDIF OPTICAL

AUDIO OUT TRIG

OUT

AV IN

L

R

18 Philips HDP15x0 & HDP15x0TV

LU Screeneo_EN.book Page 19 Jeudi, 11. dcembre 2014 8:37 08

6 Network The projector can be connected to the network by a network hard-wired cable or through a wireless (Wi-Fi) connection.

Use the procedure below appropriate to the type of connection you want.

LAN Network

Connecting to the LAN network 1 Connect one end of a LAN cable (not supplied) to

the ETHERNET port of your projector.

2 Connect the other end of the LAN cable to the net- work.

3 Configure the LAN network settings in manual or automatic configuration.

Automatic configuration The automatic configuration of the local network set- tings may be considered, if your local network features a DHCP or BOOTP server that can dynamically assign addresses to the peripheral devices present on the LAN.

To automatically configure the local network settings:

1 Switch the device on using the on/off key.

2 After the initial screen, the main menu appears.

3 Use the navigation keys to select Settings.

4 Confirm with .

5 Using / select Wireless and Networks.

6 Confirm with .

7 Using / select Lan.

8 Confirm with .

9 Using / select On.

10 Confirm with .

11 Using / select Advanced.

12 Confirm with .

13 Using / select Network address.

14 Confirm with .

15 Check that Automatic is selected.

Manual configuration To configure your projector manually, you should obtain the usual information used to set a peripheral device (IP address, sub-network mask, network and gateway address).

To configure the local network setting manually:

1 Switch the device on using the on/off key.

2 After the initial screen the main menu appears.

3 Use the navigation keys to select Settings.

4 Confirm with .

5 Using / select Wireless and Networks.

6 Confirm with .

7 Using / select Lan.

8 Confirm with .

9 Using / select On.

10 Confirm with .

11 Using / select Advanced.

12 Confirm with .

13 Using / select Network address.

14 Confirm with .

15 Using / select Use static IP.

16 Confirm with .

17 Enter the settings IP-Address, Gateway, Net- mask, DNS1 and DNS2.

18 Confirm with .

Wireless Network (WLAN) In a wireless network (Wireless Local Area Network, WLAN) at least two computers, printers or other addi- tional devices communicate with each other over radio waves (high frequency waves). Data transmission in the radio network is based on the standards 802.11a, 802.11b, 802.11g and 802.11n.

Notice Connection! The LAN connection takes priority over the Wi-Fi connection.

PHILIPS

VGA

1 2 S/PDIF OPTICAL

AUDIO OUT TRIG

OUT

AV IN

L

R

Network 19

LU Screeneo_EN.book Page 20 Jeudi, 11. dcembre 2014 8:37 08

Infrastructure Wireless Network In an infrastructure network, multiple devices commu- nicate via a central access point (gateway, router). All data are sent to the access point (gateway, router) and distributed from there.

Switching Wireless Networking (WLAN) on/off Wireless networking is deactivated by default. You have the option of turning this function on.

1 Switch the device on using the on/off key.

2 After the initial screen the main menu appears.

3 Use the navigation keys to select Settings.

4 Confirm with .

5 Using / select Wireless and Networks.

6 Confirm with .

7 Using / select WIFI.

8 Confirm with .

9 Modify the settings with /.

10 Confirm with .

The key takes you one step back in the menu.

Setting up a Wireless Network (WLAN) 1 Switch the device on using the on/off key.

2 After the initial screen the main menu appears.

3 Use the navigation keys to select Settings.

4 Confirm with .

5 Using / select Wireless and Networks.

6 Confirm with .

7 Using / select WIFI Selection.

8 Confirm with .

9 Use / to select the desired wireless network.

10 Confirm with .

11 If your wireless network is password protected, an input window appears. Select the input field (see Navigation for setting menu, page 8) using the navi- gation keys of the remote control and press OK.

12 Enter the password with the virtual keyboard using the navigation keys of the remote control or with an external keyboard.

13 Click on Connect.

The key takes you one step back in the menu.

Setting up a Wireless Network (WLAN) using the Wizard You can integrate your device very quickly and easily into an existing wireless network using Wi-Fi Protected Setup (WPS) or using a wireless network scan. Using WPS, all important settings like network name (SSID) are automatically configured and the connection pro- tected with secure WPA Encryption.

Using Wi-Fi Protected Set-up (WPS) Using Wi-Fi Protected Setup (WPS), you can integrate your device into an existing wireless network in two dif- ferent ways very quickly and easily. You can activate the login with a pin code or using Push Button Configura- tion (PBC), if your access point (Access Point, Router) supports this method.

DANGER!

Information on Using WLAN! The functioning of security systems, medical equipment or sensitive devices can be dis- rupted by the transmission power of the device. Observe any usage regulations (or restrictions) in the vicinity of such equipment.

The use of this device can affect the operation of insufficiently shielded medical devices and hearing aids and pacemakers through the release of high frequency radiation. Also con- sult a doctor or the manufacturer of the med- ical device to establish whether these are suf- ficiently shielded from external high frequency radiation.

20 Philips HDP15x0 & HDP15x0TV

LU Screeneo_EN.book Page 21 Jeudi, 11. dcembre 2014 8:37 08

Using WPS with Push Button Configuration (PBC) 1 Switch the device on using the on/off key.

2 After the initial screen the main menu appears.

3 Use the navigation keys to select Settings.

4 Confirm with .

5 Using / select Wireless and Networks.

6 Confirm with .

7 Using / select WIFI Selection.

8 Confirm with .

9 Use / to select the desired wireless network..

10 Confirm with .

11 Activate Push Button Configuration on the WLAN access point. The WLAN access point and device connect automatically and create a WPA protected connection.

Wifi Hotspot

Use the portable Wi-Fi hotspot to share the devices network connection with computers or other devices through the Wi-Fi network.

Activating WiFi hotspot 1 Switch the device on using the on/off key.

2 After the initial screen, the main menu appears.

3 Use the navigation keys to select Settings.

4 Confirm with .

5 Using / select Wireless and Networks.

6 Confirm with .

7 Using / select WiFi Hotspot.

8 Confirm with .

9 Using / select Portable WiFi Hotspot.

10 Confirm with .

11 Using / select On.

12 Confirm with .

The projector is now visible by other Wifi devices.

Notice Important! The projector can work as an access point, if only a wired lan network is installed in the location of use.

Notice Connection! When the WiFi hotspot mode is activated, it takes priority over the other connections.

Network 21

LU Screeneo_EN.book Page 22 Jeudi, 11. dcembre 2014 8:37 08

Setting up a WiFI hotspot To modify the WiFi hotspot name and define the secu- rity level.

1 Switch the device on using the on/off key.

2 After the initial screen the main menu appears.

3 Use the navigation keys to select Settings.

4 Confirm with .

5 Using / select Wireless and Networks.

6 Confirm with .

7 Using / select WiFi Hotspot.

8 Confirm with .

9 Using / select Setup WiFi hotspot. 10 Confirm with .

11 To modify the settings, use / keys to select the desired parameter.

12 Using / select Save.

13 Confirm with .

Digital Living Network Alliance (DLNA) This device supports Digital Living Network Alliance (DLNA). Using this standard you can quickly intercon- nect your multimedia devices.

Switching DLNA on and off The DLNA function is switched on by default. You have the option of turning this function off.

1 Switch the device on using the on/off key.

2 After the initial screen the main menu appears.

3 Use the navigation keys to select Settings.

4 Confirm with .

5 Using / select Wireless and Networks.

6 Confirm with .

7 Using / select DLNA Sharing.

8 Confirm with .

9 Modify the settings with /.

10 Confirm with .

The key takes you one step back in the menu.

Play Media Using DLNA If DLNA enabled devices are located in the connected network, then you can access them in media playback and file management (see Media Playback, page 25).

DLNA Control You can control the projector using another device (e.g. a smartphone) using DLNA. To do this, see the instruc- tion manual for the device in question.

Item Description

Network SSID Name of the WiFi hotspot.

This is the name used to iden- tify your projector when it is detected by another WiFi de- vice.

To modify the name, select the field and press . With the keyboard, enter the new name.

Security Select among the 3 levels of se- curity.

Open (without secu- rity)

WPA PSK WPA2 PSK

Password Select the field and press . With the keyboard, enter the new password.

Show password Check the box to display the password.

22 Philips HDP15x0 & HDP15x0TV

LU Screeneo_EN.book Page 23 Jeudi, 11. dcembre 2014 8:37 08

7 Bluetooth

Activating the Bluetooth connection 1 Switch the device on using the on/off key.

2 After the initial screen, the main menu appears.

3 Use the navigation keys to select Settings.

4 Confirm with .

5 Using / select Wireless and Networks.

6 Confirm with .

7 Using / select Bluetooth.

8 Confirm with .

9 Use / to select on.

10 Confirm with .

The projector is now visible for the near external Blue- tooth devices.

Setting up Bluetooth parameters 1 Switch the device on using the on/off key.

2 After the initial screen, the main menu appears.

3 Use the navigation keys to select Settings.

4 Confirm with .

5 Using / select Wireless and Networks.

6 Confirm with .

7 Using / select Bluetooth.

8 Confirm with .

9 Using / select the desired setting.

10 Confirm with .

11 Modify the desired settings.

Bluetooth speaker The projector can be used as Bluetooth speaker. In this mode, you can play music from smartphones or tablets.

The projector can only connect to, and play audio from one device at a time.

Activating Bluetooth speaker

1 Switch the device on using the on/off key.

2 After the initial screen, the main menu appears.

3 Depending on model, use the navigation keys to select BT Speaker or APPs>BT Speaker.

4 Confirm with OK.

Menu Description

Select device The list shows all paired devic- es.

Paired device To unconnect or unpair the paired device.

Notice Bluetooth speaker connection! Depending on the model of your device, the bluetooth speaker can be activated from the main menu (BT Speaker icon) or from the APPs menu.

Notice Remote control You can also use the SOURCE or OPTIONS key of the remote control.

Press the SOURCE key and select BT Speaker or press OPTIONS key then select SOURCE and BT Speaker.

Bluetooth 23

LU Screeneo_EN.book Page 24 Jeudi, 11. dcembre 2014 8:37 08

5 Press the Red key to power on the speaker.

6 Press the Green key to make the speaker discover- able during 60 seconds.

7 On your external device, activate the Bluetooth con- nection and select the speaker name from the list. When the device is connected, his name is displayed on the top of the screen.

8 Press the Green key to play music. During music playback, the following actions are available: Red key: To stop the connection. Green key: To make a pause. Yellow key: To play the previous music. Blue key: To play the next music.

Changing the name of the Bluetooth speaker connection This is the name used to identify your projector when it is detected by another Bluetooth device.

1 Switch the device on using the on/off key.

2 After the initial screen, the main menu appears.

3 Depending on model, use the navigation keys to select BT Speaker or APPs>BT Speaker.

4 Press the Yellow key to rename the connection.

5 Use the keyboard to enter the new name.

6 Press OK to confirm.

24 Philips HDP15x0 & HDP15x0TV

LU Screeneo_EN.book Page 25 Jeudi, 11. dcembre 2014 8:37 08

8 Media Playback

Navigating in the media Playback To navigate in the memory media, use the following keys: In order to optimize the navigation, you can select a file

type on the list:

FOLDERS to view all files (photo, audio and video).

MOVIES to view videos files only.

PICTURES to view photo files only.

MUSIC to view audio files only.

Notice Navigation Keys All the keys shown are buttons on the remote control.

Notice Best Settings for Optimal Use Read the informations on the best settings in the chapter settings (see Settings, page 33) for optimal use of your device.

Keys Action

or To select folders or files in the displayed list.

or For directories, goes one level down.

For files, starts the selected media file.

or Goes one level up in the direc- tory structure.

u Exits to main screen.

Red key of the re- mote control

Allows to set the repeat mode for movie and music files:

: Play mode deacti- vate (greyed).

: Play only the selected movie in loop.

: Play all movies in the selected directory in loop.

: Play all movies in the media in loop.

Green key of the remote control

Allows to set the slide show parameters for picture files.

or

Allows to set the shuffle mode for music files:

: Shuffle mode deactivate (greyed).

: Shuffle mode acti- vate.

Yellow key of the remote control

Allows to display the pictures as miniatures or in a list.

Blue key of the re- mote control

Allows to delete the selected file.

Keys Action

Media Playback 25

LU Screeneo_EN.book Page 26 Jeudi, 11. dcembre 2014 8:37 08

Video playback

Supported file formats Supported file formats are *.avi, *.mov, *.mp4, *.mkv, *.flv, *.ts, *.m2ts, *.3gp.

Video Playback (USB/SD Card/ Internal Memory/DLNA) 1 Switch the device on using the on/off key.

2 The main menu appears.

3 Use the navigation keys to select the desired media (USB, SD-card or DLNA): Memory Internal memory or SD card can be selected. USB - If only one USB key is connected the explorer shows only the content of the USB. - If more than one USB memory is connected, select the desired USB memory first. DLNA The explorer searches for servers and shows them in a list. Select the desired DLNA server.

4 Confirm with . The content of selected media is displayed.

5 To only display the movies content, select Movie using the keys /on the left of the screen.

6 Confirm with .

7 Use / to select the video file that you wish to play.

8 Press or to start playback.

9 Press to end the slide show and return to the overview.

10 When you press again, you will return to the main menu.

During playback you can adjust the volume using the

keys / on the remote control. Press or repeatedly to shut off the volume completely.

Photo Playback

Supported file formats Supported file formats are JPEG, BMP, PNG and GIF.

Photo Playback (USB/SD Card/ Internal Memory/DLNA) 1 Switch the device on using the on/off key.

2 The main menu appears.

3 Use the navigation keys to select the desired media (USB, SD-card or DLNA): SD-card Internal memory or SD card can be selected! USB - If only one USB key is connected the explorer shows only the content of the USB. - If more than one USB memory is connected, select the desired USB memory first. DLNA The explorer searches for servers and shows them in a list. Select the desired DLNA server.

4 Confirm with . The content of selected media is displayed.

Notice The use of color keys The Red key allows to set the repeat mode:

: Play mode deactivate (greyed).

: Play only the selected movie in loop.

: Play all movies in the selected directory in loop.

: Play all movies in the media in loop.

The Blue key alows to delete the selected file.

Notice Displaying Video Files Only those videos that are compatible with the projector will be displayed.

Notice Navigation During Playback Review / forward: Press :/; on the remote control.

Press T to stop or continue playback.

26 Philips HDP15x0 & HDP15x0TV

LU Screeneo_EN.book Page 27 Jeudi, 11. dcembre 2014 8:37 08

5 To only display the picture content, select Picture using the keys /on the left of the screen and confirm with .

6 The list of photos are displayed on the screen as an overview.

7 Use / or / to select the image that you want to start the slide show with.

8 Press Green key to start the slide show.

9 To modify the settings, use / keys to select the desired parameter.

10 Press Green key to start the slide show.

11 Press to pause the slide show.

12 Press to end the slide show and return to the overview.

13 When you press u, you will return to the main menu.

Slide Show with Background Sound 1 During the slide show, press to display the menu

bar on the bottom of the screen.

2 Using / select .

3 Confirm with .

4 Use / to select the file that you wish to play.

5 To start the background sound confirm with .

6 Adjust the volume level with the volume keys on the remote control.

7 If no input is made, the menu bar is hidden after 5 seconds.

Zoom and rotate functions During the slide show, press OK key to display the con- textual menu.

To perform a zoom, use the navigation keys to select

the symbol then press OK.

To rotate a picture, use the navigation keys to select the

symbol then press OK to rotate the picture 90 clockwise.

Press return to the slide show.

Notice The use of color keys The Green key allows to set the slide show parameters.

The Yellow key allows to display the pictures as miniatures or in a list.

The Blue key allows to delete the selected file.

Notice Many Photos on the Memory Card or the USB Medium If there are a lot of photos on the memory card or the USB storage medium it can take a moment before the overview appears.

Notice The slide show can be started with the OK keyif the parameters have already been set up.

Item Description

Time per slide To modify the photo display frequency.

Off, 0, 2, 5, 10, 20, 30 and 60s

Repeat Off, Directory or All

Slide transition To modify the type of transi- tion from one photo to anoth- er (random or by theme).

Slideshow order Random or by order

Notice Storage Location Only files from the internal memory/Mem- ory Card/USB Storage Medium can be played.

Media Playback 27

LU Screeneo_EN.book Page 28 Jeudi, 11. dcembre 2014 8:37 08

Music Playback

Supported file formats Supported file formats are MP3 and WAV.

Music Playback (USB/SD Card/ Internal Memory/DLNA) 1 Switch the device on using the on/off key.

2 The main menu appears.

3 Use the navigation keys to select the desired media (USB, SD-card or DLNA): SD-card Internal memory or SD card can be selected! USB - If only one USB key is connected the explorer shows only the content of the USB. - If more than one USB memory is connected, select the desired USB memory first. DLNA The explorer searches for servers and shows them in a list. Select the desired DLNA server.

4 Confirm with . The content of selected media is displayed.

5 To only display the music content, select Music using the keys /on the left of the screen and confirm with .

6 Use / to select the file that you wish to play.

7 Press to start playback.

8 Press T to stop or continue playback.

During playback you can adjust the volume using the

keys / on the remote control. Press or repeatedly to shut off the volume completely.

Notice Switch off the Image Playback You can switch off the screen while playing music in order to save power by a long press

on the key.

Notice The use of color keys The Red key allows to set the repeat mode:

: Play mode deactivate (greyed).

: Play only the selected music in loop.

: Play all musics in the selected directory in loop.

: Play all musics in the media in loop.

The Green key allows to set the shuffle mode:

: Shuffle mode deactivate (greyed).

: Shuffle mode activate.

The Blue key allows to delete the selected file.

Notice Navigating when Image Playback is Switched off Press / to skip to the previous or next song.

Press T to stop or continue playback.

Press to return to the selection.

28 Philips HDP15x0 & HDP15x0TV

LU Screeneo_EN.book Page 29 Jeudi, 11. dcembre 2014 8:37 08

Managing Files

Delete Files You can delete files from the internal memory, the con- nected USB storage medium or the memory card.

1 Switch the device on using the on/off key.

2 The main menu appears.

3 Use the navigation keys to select the desired media (USB, Memory or DLNA).

4 Confirm with .

5 Use / to select the file that you want to delete.

6 Press the Blue key on the remote control to delete the file.

7 Confirm with .

Notice Error If errors occur during the deletion pro- cess, make sure that the storage medium is not write-protected.

Media Playback 29

LU Screeneo_EN.book Page 30 Jeudi, 11. dcembre 2014 8:37 08

9 Digital TV Playback (Depending on model)

Connecting the Aerial

1 Connect the aerial to the aerial socket.

First Playback

When the DVB-T function is first started, the automatic channel search must be started.

1 Switch the device on using the on/off key.

2 The main menu appears.

3 Connect the aerial (see Connecting the Aerial, page 30).

4 Use the navigation keys to select TV.

5 Confirm with .

6 Use / to highlight a setting and use the / to select a value. - Select the country. - Select the level of the parental control. - Enter the PIN code for channel lock or parental control. Enter the code with 4 digits (0000 is not accepted) and enter again the same code to confirm.

7 Press OK to confirm the settings and continue the installation. The channel search starts automatically.

8 At the end of the search, press . Your TV is now set. You can start watching and enjoy- ing all your channels.

Television

Notice Aerial Size and Orientation In some regions it is necessary to connect a larger aerial in order to grant the reception.

In some countries it is necessary to point the aerial horizontally in order to grant the recep- tion.

PHILIPS

VGA

1 2 S/PDIF OPTICAL

AUDIO OUT TRIG

OUT

AV IN

L

R

Notice Navigation Keys All the keys shown are buttons on the remote control.

Notice Navigation Keys All the keys shown are buttons on the remote control.

30 Philips HDP15x0 & HDP15x0TV

LU Screeneo_EN.book Page 31 Jeudi, 11. dcembre 2014 8:37 08

1 Switch the device on using the on/off key.

2 The main menu appears.

3 Use the navigation keys to select TV.

4 Confirm with OK.

5 The last viewed channel is played. Change the chan- nel using keys CH+/CH-, / or enter directly the number with the keypad.

6 Press u to end playback and return to the main menu.

During playback you can adjust the volume using the

keys / or / on the remote control.

Press or repeatedly to shut off the volume completely.

Modifying the DVB-T settings To modify DVB-T settings, press the Menu key on the remote control. Main menus are:

Edit channels: To display and modify the channel and radio lists.

Installation: To launch an automatic or a manual search for channels.

System Setup: To modify the parental lock settings, the display settings and the favorite settings.

Notice Displaying Channel Information When changing channel, channel informa- tion is displayed on the bottom projection edge. The information bar is hidden after 5 seconds.

Digital TV Playback (Depending on model) 31

LU Screeneo_EN.book Page 32 Jeudi, 11. dcembre 2014 8:37 08

10 Android Your projector uses the Android operating system.

Starting Android Apps 1 Switch the device on using the on/off key.

2 After the initial screen the main menu appears.

3 Use the navigation keys to select APPs.

4 Confirm with OK.

Exiting Android Press the u key to return to the main menu.

Installing Android-Apps

You can install other apps. Use the APK installation packets, proceed as follows:

1 Download the package APK and save it onto a mem- ory card or USB-stick.

2 Insert the memory card into the device (see Insert- ing a Memory Card, page 18).

3 Switch the device on using the on/off key.

4 After the initial screen the main menu appears.

5 Use the navigation keys to select APPs

6 Confirm with OK.

7 Use the navigation keys to select ApkInstaller.

8 Confirm with OK.

9 Use the navigation keys to select Install.

10 Confirm with OK.

11 Navigate to the memory card and select the APK package you want to install.

12 Press OK to execute the installation package.

13 The APK package is installed.

CAUTION!

Trusted Sources! Apps from third party sources may be mali- cious. Only use installation packets from trusted sources.

32 Philips HDP15x0 & HDP15x0TV

LU Screeneo_EN.book Page 33 Jeudi, 11. dcembre 2014 8:37 08

11 Settings 1 Switch the device on using the on/off key.

2 After the initial screen the main menu appears.

3 Use the navigation keys to select Settings.

4 Confirm with OK.

5 Use / to select from the following settings.

6 Confirm with OK.

7 Modify the settings using OK, /,

8 Confirm with OK.

The key takes you one step back in the menu.

Overview of the Menu Functions Wireless and Network WiFi switching the wireless network (WLAN) off and on.

Network Selection select the wireless network with which the device is to connect.

WiFi Hot Spot activate and deactivate WLAN teth- ering.

LAN switching the LAN network (LAN) off and on.

Advanced (LAN mode only) check the Network actual IP address or change the address by inputting new address. You can also select Automatic or Use static IP DLNA Sharing switching DLNA off and on.

Bluetooth switching the Bluetooth connection off and on.

Image settings 3D set the picture modes with 2D/3D options.

Keystone use / to set the keystone.

Fit Screen use / to select the screen mode

Projection mode

Front normal projection; the device is located in front of the projection surface/screen

Rear rear projection; the device is located behind the projection surface; the image is reflected hori- zontally.

Front Ceiling the device is hanging from the ceiling in an upside-down position; the image is rotated by 180 degrees.

Rear ceiling the device is located behind the pro- jection surface, hanging from the ceiling in an upside- down position; the image is rotated by 180 degrees and reflected horizontally.

Wall color correction colour correction of the pro- jected image to adjust to coloured projection surfaces

Smart Settings select predefined settings for bright- ness / contrast / colour saturation. If you modify these settings, the setting is switched to Manual.

Brightness use / to adjust the brightness and press OK to confirm.

Contrast use / to adjust the contrast and press OK to confirm.

Advanced

Colour temperature set to Warm to enhance hotter colors such as red, or set to Cool to make picture bluish.

Smart Brightness use / to adjust the smart brightness and press OK to confirm.

Dynamic contrast adjusts the contrast to keep it at the best level according to the brightness of the screen.

Color space to convert the color space setting to another standard.

Gamma adjusts the gamma correction according to the type of the projected image.

Sound Settings: Volume adjust the volume

Deep Bass switching the deep bass on and off

Wide sound switching the wide sound on and off

Equalizer select the equalizer mode

Smart volume turn on/off the volume level automatic control function

Key beep turn key tones on and off

Speaker switching the speaker on and off

System settings Date and time set date and time

Android Settings set Android system

Sleep mode With this function, the projector auto- matically goes to ECO mode after a specified period of time or at the end of a movie.

Auto Power Down turn on/off the sleep mode. The default setting is off.

Settings 33

LU Screeneo_EN.book Page 34 Jeudi, 11. dcembre 2014 8:37 08

When the parameter is switched on, it works like this:

- If the projector is on, while no video is displayed (e.g. menu open without user action), it should go into off mode after the shortest possible time, by example 30 minutes.

- If a video is displayed, the APD should take place 3h after last user action, meaning that a pop-up will appear after 2h58 for 2 minutes, indicating that the product will go into off mode.

HDMI name select this item to change the HDMI names. Name that appears on the main screen.

Language/Language Menu language use / to select the desired lan- guage and press OK to confirm.

Soundtrack use / to select the desired lan- guage and press OK to confirm.

Sub Title use / to select the desired language and press OK to confirm.

Maintenance Reset settings Reset settings to factory defaults.

Firmware Update Update Firmware

Information Display free space in the internal mem- ory and information on the device (Capacity: / Free space: / Firmware version: / Device name: / Model:)

Demo mode switching demo mode on and off.

34 Philips HDP15x0 & HDP15x0TV

LU Screeneo_EN.book Page 35 Jeudi, 11. dcembre 2014 8:37 08

12 Service

Cleaning

Cleaning the Lens Use a brush or lens cleaning paper for cleaning the lens of the projector.

Device Overheated A overheat symbol appears if the device is overheated.

Update Firmware with Memory Card 1 Use SD memory card in the file system FAT16 or

FAT32.

2 Save the latest firmware update file to the root of the memory card.

3 Insert the memory card (see Inserting a Memory Card, page 18) and switch the device on.

4 Use the navigation keys to select Settings.

5 Confirm with .

6 Use / to select Maintenance.

7 Confirm with .

8 Use / to select Firmware Update.

9 Confirm with .

10 Use / to select Install.

11 Confirm with .

12 The device turns off and on again. After around 5 minutes the Language Selection screen appears. The firmware update is now completed.DANGER!

Instructions for Cleaning! Use a soft, lint-free cloth. Never use liquid or easily flammable cleansers (sprays, abrasives, polishes, alcohol, etc.). Do not allow any moisture to reach the interior of the device. Do not spray the device with any cleaning flu- ids.

Wipe over the surfaces gently. Be careful that you do not scratch the surfaces.

DANGER!

Do not use any Liquid Cleaning Agents Do not use any liquid cleaning agents for cleaning the lens, to avoid damaging the coat- ing film on the lens.

DANGER!

All Data will be Deleted! This procedure erases all your data that is stored on the memory card.

DANGER!

Inserting a Memory Card! Never pull out the memory card while the device is accessing it. This could cause data to be damaged or lost.

Notice If an error occurs during the firmware update process retry the procedure or contact your dealer.

Service 35

LU Screeneo_EN.book Page 36 Jeudi, 11. dcembre 2014 8:37 08

Troubleshooting

Power Cycling If a problem occurs that cannot be corrected with the instructions in this user manual (see also the help below), follow the steps given here.

1 Switch the device off using the on/off key on the panel control.

2 Wait at least ten seconds.

3 Switch the device on using the on/off key on the panel control.

4 If the problem repeats, please contact our technical customer service or your retailer.

Problems Solutions

The projector cannot be switched on Disconnect and Connect the power supply cable and try again.

The projector cannot be switched off Disconnect the power supply cable.

No sound check that the speaker is activated (Settings /Sound setting/Speaker).

Adjust the volume using the / key on the remote control.

No sound from the external connected device Check the cables to the external device Set the volume on the external device Only the original cables from the device manufac-

turer may function

No sound from DVB-T program or external HDMI out- put device.

Set the audio setting to Multichannel (Raw data) & Stereo (PCM).

No sound when you connect your computer via HDMI cable

Check that the sound is activated on the computer.

Video display problem when the source is a 3D signal from a DVD player.

Check that the 3D mode is activated on the projec- tor.

If the DVD player is connected to the projector via HDMI, only use the HDMI sockets (1 or 2) located on the rear of the device.

Only the initial screen appears and not the image from the external device

Check if the cables are connected to the right sock- ets.

Please check that the external device is switched on Check if the video output of the external device is

switched on. Check that the HDMI source selected on the user

interface corresponds to HDMI connector where the external device is connected.

Only the initial screen appears and not the image from the connected computer

Please check that the VGA-output of the computer is switched on.

Check if the resolution of the computer is set to 1280*800(for VGA connection) or 1080P(for HDMI connection).

36 Philips HDP15x0 & HDP15x0TV

LU Screeneo_EN.book Page 37 Jeudi, 11. dcembre 2014 8:37 08

The device turns itself off When the device is running for a long period of time, the surface becomes hot and a warning symbol appears on the projection (see Symbols in the Status- bar, page 9). The device automatically turns off when it gets too hot. After the device has cooled down, you can continue playback.

Check that the power cable is connected correctly. Check the sleep mode status in the setting menu ().

When the sleep mode is activated, the device turn off after the programmed duration.

The device changes from maximum level of brightness to minimum level of brightness when the device is connect- ed over USB to play videos.

When the environment temperature is too high, the devices turns automatically from maximum level of brightness to minimum level of brightness in order to protect the high power LED.

Use the device with lower environment tempera- tures.

The device cannot connect with an Android device (for example a mobile phone/smartphone with the Android operating system) when connected via USB.

Deactivate the function USB debugging in the set- tings menu of your Android device before connect- ing the Projector via USB; your Android device should be recognized as USB storage medium.

Bad image or color quality when connecting with HDMI Use the supplied HDMI cable. Third-party cables may cause signal distortions.

The device cannot read the SD card. Check that the memory card is compatible (see the list in the chapter Appendix).

The device cannot read the USB stick The device does not support the exFAT file system. Format the USB key in FAT format, then use it.

The TV icon doesn't appear while the DVB-T module is installed.

Call the hot-line.

Problems Solutions

Service 37

LU Screeneo_EN.book Page 38 Jeudi, 11. dcembre 2014 8:37 08

13 Appendix

Technical Data Dimensions (LHW) .................... 287 148 339 mm Weight ........................................................................... 5,3 kg Recommended Ambient ......................................5 35 C Relative Humidity ................15 85 % (non-condensing) File format................................ *.avi, *.mov, *.mp4,*.mkv,

................................................ *.flv, *.ts, *.m2ts, *.3gp Photo formats ................................. JPEG, BMP, PNG, GIF Music formats..................................................... MP3, WAV Video Standard (CVBS)................... PAL, SECAM, NTSC Video connection .........................................HDMI sockets Internal speaker ............... stereo with subwoofer, 26 W Internal memory............................................................4 GB Compatible Memory Cards ......SD/SDHC/SDXC/MMC USB connection max. power...........................5V, 500mA

Technology / optical Display technology ...............................WXGA 0.45" DLP Light source ........................................................... RGB LED Native resolution......................... 1280 x 800 Pixel (16:9) Supported Resolutions..................... VGA/SVGA/WVGA

..............................................XGA/WXGA/FULL HD Projected image size (inch)...........................50 up to 100 Screen distance (mm).................................. 108 up to 441 Display refresh rate ............................. 60Hz/50Hz/120Hz

Power supply Input .......................................100V-240V, 4.0 A, 50/60HZ Power consumption....................................................150W Off mode power consumption .............................. <0,5W Manufacturer .................................... JQH Group Co., Ltd.

Accessories Following accessories are available for your device: PVideo-(CVBS) cable.....................PPA1320 / 253526178

All data are provided for reference purposes only. Sagemcom Documents SAS reserves the right to make any changes without prior notice.

38 Philips HDP15x0 & HDP15x0TV

LU Screeneo_EN.book Page 39 Jeudi, 11. dcembre 2014 8:37 08

The CE marking certifies that the product meets the main requirements of the European Parliament and Council directives 1999/5/CE, 2006/95/CE, 2004/108/ CE and 2009/125/CE on information technology equip- ment, regarding safety and health of users and regarding electromagnetic interference.

The declaration of compliance can be consulted on the site www.screeneo.philips.com.

Preservation of the environment as part of a sustainable development plan is an essential concern of Sagemcom Documents SAS. The desire of Sagemcom Documents SAS is to operate systems observing the environment. The desire of Sagemcom Documents SAS is to operate systems observing the environment and consequently it has decided to integrate environmental performances in the life cycle of this products, from manufacturing to commissioning use and elimination.

Packaging: The presence of the logo (green dot) means that a contribution is paid to an approved national organisation to improve package recovery and recycling infrastructures. Please respect the sorting rules set up locally for this kind of waste.

Batteries: If your product contains batteries, they must be disposed of at an appropriate collection point.

Product: The crossed-out waste bin stuck on the product means that the product belongs to the family of electrical and electronic equipment. In this respect, the European regulations ask you to dispose of it selectively;

At sales points in the event of the purchase of similar equipment.

At the collection points made available to you locally(drop-off centre, selective collection, etc.).

In this way you can participate in the re-use and upgrad- ing of Electrical and Electronic Equipment Waste, which can have an effect on the environment and human health.

The paper and cardboard packaging used can be dis- posed of as recyclable paper. Have the plastic wrapping recycled or dispose of it in the non-recyclable waste, depending on the requirements in your country.

Trademarks: The mentioned references in this man- ual are trademarks of the respective companies. The lack of the trademarks and does not justify the assumption that these dedicated terminologies are free trademarks. Other product names used herein are for identification purposes only and may be trademarks of their respective owners. Sagemcom Documents SAS disclaims any and all rights in those marks.

Neither Sagemcom Documents SAS nor its affiliates shall be liable to the purchaser of this product or third parties for damages, losses, costs, or expenses incurred by the purchaser or third parties as a result of accident, misuse, or abuse of this product or unauthorized mod- ifications, repairs, or alterations to this product, or fail- ure to strictly comply with Sagemcom Documents SAS operating and maintenance instructions.

Sagemcom Documents SAS shall not be liable for any damages or problems arising from the use of any options or any consumable materials other than those designated as original Sagemcom Documents SAS / PHILIPS products or Sagemcom Documents SAS / PHILIPS approved products.

Sagemcom Documents SAS shall not be held liable for any damage resulting from electromagnetic interference that occurs from the use of any interface cables other than those designated as Sagemcom Documents SAS / PHILIPS products.

All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of Sagemcom Documents SAS. The information contained herein is designed only for use with this product. Sagemcom Documents SAS is not responsible for any use of this information as applied to other devices.

This user manual is a document that does not represent a contract.

Errors, printing errors and changes are reserved.

Copyright 2014 Sagemcom Documents SAS

Appendix 39

HDP15x0 & HDP15x0TV EN

253571339-D

PHILIPS and the PHILIPS Shield Emblem are registered trademarks of Koninklijke Philips N.V. and are used by Sagemcom Documents SAS under license from Koninklijke Philips N.V. 2014 Sagemcom Documents SAS All rights reserved

Sagemcom Documents SAS Documents Business Unit

Headquarters : 250, route de lEmpereur 92848 Rueil-Malmaison Cedex FRANCE Tel: +33 (0)1 57 61 10 00 Fax: +33 (0)1 57 61 10 01 www.sagemcom.com Simplified Joint Stock Company Capital 8.479.978 509 448 841 RCS Nanterre

LU Screeneo_EN.book Page 40 Jeudi

Manualsnet FAQs

If you want to find out how the Screeneo Philips works, you can view and download the Philips Screeneo HDP1590TV Projector User Manual on the Manualsnet website.

Yes, we have the User Manual for Philips Screeneo as well as other Philips manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The User Manual should include all the details that are needed to use a Philips Screeneo. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Philips Screeneo HDP1590TV Projector User Manual is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Philips Screeneo HDP1590TV Projector User Manual consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Philips Screeneo HDP1590TV Projector User Manual free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Philips Screeneo HDP1590TV Projector User Manual, simply download the document to your computer. Once downloaded, open the PDF file and print the Philips Screeneo HDP1590TV Projector User Manual as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.